MOTEUR / ENGINE OK-Junior
|
|
|
- Reynard Sherman
- 6 years ago
- Views:
Transcription
1 FICHE D HOMOLOGATION HOMOLOGATION FORM Homologation N COMMISSION INTERNATIONALE DE KARTING - FIA MOTEUR / ENGINE OK-Junior Constructeur Manufacturer IAME S.P.A. ZINGONIA (I) Marque Make PARILLA Modèle Model REEDSTER 4 JUNIOR Type d admission Inlet type REEDVALVE Durée de l homologation Validity of the homologation 9 ans / 9 years Nombre de pages Number of pages 18 La présente Fiche d Homologation reproduit descriptions, illustrations et dimensions du moteur au moment de l homologation par la CIK-FIA. La hauteur du moteur complet sur les photos doit être de 7 cm minimum. This Homologation Form reproduces descriptions, illustrations and dimensions of the engine at the time the CIK-FIA conducted the homologation. The height of the complete engine on all photographs must be as a minimum 7 cm. PHOTO DU MOTEUR CÔTÉ PIGNON PHOTO OF DRIVE SIDE OF ENGINE Signature et tampon de l ASN Signature and stamp of the ASN PHOTO DU MOTEUR CÔTÉ OPPOSÉ PHOTO OF OPPOSITE SIDE OF ENGINE Signature et tampon de la CIK-FIA Signature and stamp of the CIK-FIA Copyright 2015 by CIK-FIA. All rights reserved. 1
2 Homologation N PHOTO DU MOTEUR COMPLET COTÉ PIGNON PHOTO OF DRIVE SIDE OF THE COMPLETE ENGINE Copyright 2015 by CIK-FIA. All rights reserved. 2
3 Homologation N PHOTO DU MOTEUR COMPLET COTÉ OPPOSÉ AU PIGNON PHOTO OF OPPOSITE DRIVE SIDE OF THE COMPLETE ENGINE Copyright 2015 by CIK-FIA. All rights reserved. 3
4 Homologation N PHOTO DE L ARRIÈRE DU MOTEUR COMPLET PHOTO OF THE REAR OF THE COMPLETE ENGINE Copyright 2015 by CIK-FIA. All rights reserved. 4
5 Homologation N PHOTO DE L AVANT DU MOTEUR COMPLET PHOTO OF THE FRONT OF THE COMPLETE ENGINE Copyright 2015 by CIK-FIA. All rights reserved. 5
6 Homologation N PHOTO DU MOTEUR COMPLET VU DU HAUT PHOTO OF THE COMPLETE ENGINE TAKEN FROM ABOVE Copyright 2015 by CIK-FIA. All rights reserved. 6
7 Homologation N PHOTO DU MOTEUR COMPLET VU DU DESSOUS PHOTO OF THE COMPLETE ENGINE TAKEN FROM BELOW Copyright 2015 by CIK-FIA. All rights reserved. 7
8 Homologation N INFORMATIONS TECHNIQUES TECHNICAL INFORMATION A CARACTÉRISTIQUES A CHARACTERISTICS Le nombre de décimales doit être de 2 ou en accord avec la tolérance appliquée. The number of decimal places must be 2 or comply with the relevant tolerance. Tolérances / remarques Tolerances & remarks Cylindre Cylinder Volume du cylindre Volume of cylinder cm³ <125cm³ Alésage d origine Original bore 53.89mm -- Alésage théorique maximum Theoritical maximum bore 54.08mm -- Course Stroke 54.40mm -- Nombre de canaux de transfert, cylindre/carter Nombre de lumières / canaux d échappement Forme de la chambre de combustion Number of transfer ducts, 5 / 3 -- cylinder/sump Number of exhaust ports / ducts 3 -- Shape of the combustion chamber SPHERIC+SQUISH Vilebrequin Crankshaft Nombre de paliers Number of bearings 2 -- Diamètre des paliers Diameter of bearings 25 ±0.1mm Poids minimum du vilebrequin Minimum weight of crankshaft 1820g minimum Arbre d équilibrage Balance shaft Poids minimum de l arbre d équilibrage Minimum weight of balance shaft 195g minimum Pourcentage d Equilibrage Percentage of balancing 25% minimum Bielle Connecting rod Longueur (entre-axe) de la bielle Connecting rod centreline 104mm ±0.2mm Diamètre de la tête de bielle Diameter of big end 26mm ±0.05mm Diamètre du pied de bielle Diameter of small end 19mm ±0.05mm Poids minimum de la bielle Min. weight of the connecting rod 89g minimum Copyright 2015 by CIK-FIA. All rights reserved. 8
9 Homologation N Piston Piston Nombre de ségments du piston Number of piston rings 1 Poids minimum du piston nu Min. weight of the bare piston 113g ségments du piston inclus including piston rings minimum Axe du piston Gudgeon pin Poids minimum Minimum weight 26g Minimum B ANGLES D OUVERTURE B OPENING ANGLES De l échappement Of the exhaust selon les règlements according to the regulations C MATÉRIAU C MATERIAL Culasse Cylinder head Al-Si or Al-Si+Fe or Al-Si+Cu Cylindre Cylinder AL-SI / FONTE Carter Sump AL-SI Vilebrequin Crankshaft ACIER NI-CR-MO Bielle Connecting rod ACIER NI-CR-MO Piston Piston AL-SI Copyright 2015 by CIK-FIA. All rights reserved. 9
10 Homologation N D PHOTOS, DESSINS & GRAPHIQUES D PHOTOS, DRAWINGS & GRAPHS D.1 CYLINDRE / CYLINDER UNIT DESSIN DU DÉVELOPPEMENT DU CYLINDRE sans dimensions DRAWING OF THE CYLINDER DEVELOPMENT without dimensions DESSIN DU PIED DU CYLINDRE sans dimensions DRAWING OF THE CYLINDER BASE without dimensions PHOTO DU PIED DU CYLINDRE PHOTO OF THE CYLINDER BASE Copyright 2015 by CIK-FIA. All rights reserved. 10
11 Homologation N... Section D.1 DESSIN DE LA CULASSE ET DE LA CHAMBRE DE COMBUSTION sans dimensions ALTERNATIVE DRAWING OF THE CYLINDER HEAD AND OF THE COMBUSTION CHAMBER without dimensions VUE EN COUPE VERTICALE DU CYLINDRE AVEC LA CHEMISE, sans dimensions VERTICAL CROSS SECTION VIEW OF CYLINDER WITH LINER, without dimensions Copyright 2015 by CIK-FIA. All rights reserved. 11
12 Homologation N D.2 BIELLE, CARTERS, VILEBREQUIN & PISTON / CONROD, CRANKCASE, CRANKSHAFT & PISTON PHOTO DE L EMBIELLAGE PHOTO OF THE CRANKSHAFT & CONROD PHOTO DE LA BIELLE PHOTO OF THE CONROD DESSIN DE L ENSEMBLE VILEBREQUIN - DRAWING OF THE CRANKSHAFT - CON ROD BIELLE (DIMENSIONS avec tolérances, largeurs UNIT (DIMENSIONS incl. tolerances, big & small pied & tête de bielle, largeur & diamètre des ends thickness, crank mass thickness & contrepoids) diameter ) Copyright 2015 by CIK-FIA. All rights reserved. 12
13 Homologation N...Section D.2 DESSIN DU PISTON (DIMENSIONS DRAWING OF THE PISTON (MAIN PRINCIPALES avec tolérances) DIMENSIONS incl. tolerances) PHOTO INTÉRIEURE DU CARTER DROIT PHOTO OF THE INSIDE OF THE RH CRANKCASE PHOTO INTÉRIEURE DU CARTER GAUCHE PHOTO OF THE INSIDE OF THE LH CRANKCASE Copyright 2015 by CIK-FIA. All rights reserved. 13
14 Homologation N D.3 ARBRE D ÉQUILIBRAGE / BALANCE SHAFT PHOTO DE L ARBRE D ÉQUILIBRAGE PHOTO OF THE BALANCE SHAFT DESSIN DE L ARBRE D ÉQUILIBRAGE DRAWING OF THE BALANCE SHAFT (DIMENSIONS avec tolérances) (DIMENSIONS incl. tolerances) Copyright 2015 by CIK-FIA. All rights reserved. 14
15 Homologation N D.4 CLAPETS / REED VALVE DESSIN DE LA BOÎTE À CLAPETS (DIMENSIONS avec tolérances) DRAWING OF THE REED VALVE (DIMENSIONS incl. tolerances) OPTIONAL 1 EN OPTION 1 OPTIONAL 2 EN OPTION 2 Copyright 2015 by CIK-FIA. All rights reserved. 15
16 Homologation N D.5 MARQUAGE PIECES PRINCIPALES / MAIN PARTS MARKING Pour chaque piéce, photo globale avec le marquage et photo avec zoom sur le marquage For each part, global picture with marking and zoom picture on marking 1. Fonderies de carter, couvercle d engrenages, cylindre, culasse 2. Chemise en fonte 3. Demi-vilebrequins 4. Bielle 5. Arbre d équilibrage 6. Engrenages 7. Piston 1. Castings of crankcase, gears cover, cylinder, cylinder head 2. Cast iron liner 3. Half-crankshafts 4. Conrod 5. Balancer shaft 6. Gears 7. Piston Piéces N / Parts no. Photo globale / global picture Zoom Copyright 2015 by CIK-FIA. All rights reserved. 16
17 Homologation N Copyright 2015 by CIK-FIA. All rights reserved. 17
18 Homologation N Copyright 2015 by CIK-FIA. All rights reserved. 18
MOTEUR / ENGINE OK-Junior
FICHE D HOMOLOGATION HOMOLOGATION FORM Homologation N COMMISSION INTERNATIONALE DE KARTING - FIA MOTEUR / ENGINE OK-Junior Constructeur Manufacturer OTK KART GROUP S.R.L. (ITALY) Marque Make VORTEX Modèle
FICHE D HOMOLOGATION HOMOLOGATION FORM COMMISSION INTERNATIONALE DE KARTING - FIA. MOTEUR / ENGINE OK-Junior
Homologation N FICHE D HOMOLOGATION HOMOLOGATION FORM COMMISSION INTERNATIONALE DE KARTING - FIA MOTEUR / ENGINE OK-Junior Constructeur Manufacturer ASPA S.R.L. Marque Make MODENA ENGINES Modèle Model
COMMISSION INTERNATIONALE DE KARTING - FIA
FICHE D HOMOLOGATION HOMOLOGATION FORM Homologation N COMMISSION INTERNATIONALE DE KARTING - FIA MOTEUR / ENGINE OK Constructeur Manufacturer TM RACING S.P.A. Marque Make TM RACING Modèle Model S-SENIOR
COMMISSION INTERNATIONALE DE KARTING - FIA
FICHE D HOMOLOGATION HOMOLOGATION FORM Homologation N COMMISSION INTERNATIONALE DE KARTING - FIA MOTEUR / ENGINE KF3 Constructeur Manufacturer OTK-KART-GROUP S.R.L.-(ITALY) Marque Make VORTEX Modèle Model
COMMISSION INTERNATIONALE DE KARTING - FIA
FICHE D HOMOLOGATION HOMOLOGATION FORM Homologation N COMMISSION INTERNATIONALE DE KARTING - FIA MOTEUR / ENGINE KF2 Constructeur Manufacturer OTK-KART-GROUP S.R.L.-(ITALY) Marque Make VORTEX Modèle Model
MOTEUR / ENGINE COMMISSION INTERNATIONALE DE KARTING - FIA FICHE D HOMOLOGATION HOMOLOGATION FORM 40/M/15 KF4
FICHE D HOMOLOGATION HOMOLOGATION FORM Homologation N COMMISSION INTERNATIONALE DE KARTING - FIA MOTEUR / ENGINE KF4 Constructeur Manufacturer TM RACING S.p.A Marque Make TM RACING Modèle Model MF1 Durée
17/M/24 PHOTO DE L ARRIÈRE DU MOTEUR COMPLET PHOTO OF THE REAR OF THE COMPLETE ENGINE THIS PAGE CANCELS AND REPLACES PAGE 4 OF THE CIK-FIA FICHE
THIS PAGE CANCELS AND REPLACES PAGE 4 OF THE CIK-FIA FICHE PHOTO DE L ARRIÈRE DU MOTEUR COMPLET PHOTO OF THE REAR OF THE COMPLETE ENGINE Page 1 of 9 THIS PAGE CANCELS AND REPLACES PAGE 9 OF THE CIK-FIA
COMMISSION INTERNATIONALE DE KARTING - FIA
FICHE D HOMOLOGATION HOMOLOGATION FORM Homologation N COMMISSION INTERNATIONALE DE KARTING - FIA MOTEUR / ENGINE KF4 Constructeur Manufacturer TM RACING S.P.A. Marque Make TM RACING Modèle Model MF3 Durée
ENGINE HOMOLOGATION FORM. Constructeur Manufacturer Marque Make Modèle Model Nombre de pages Number of pages 18. Homologation N
HOMOLOGATION FORM Homologation N ENGINE Constructeur Manufacturer Marque Make Modèle Model Nombre de pages Number of pages 18 Copyright by X125 and Italian Motors. All rights reserved. 1 TECHNICAL INFORMATION
HOMOLOGATION FORM. Constructeur Manufacturer Marque Make Modèle Model Nombre de pages Number of pages 20. Homologation N
HOMOLOGATION FORM Homologation N ENGINE Constructeur Manufacturer Marque Make Modèle Model Nombre de pages Number of pages 20 Copyright by X125 and Italian Motors. All rights reserved. 1 TECHNICAL INFORMATION
X30 125cc RL-C TaG FEATURES - CARACTERISTIQUES. Cylinder volume Volume du cylindre cm³. Bore Alésage. 54 mm
X30 125cc RL-C TaG FEATURES - CARACTERISTIQUES Cylinder volume Volume du cylindre 123.67 cm³ Bore Alésage 54 mm Max. theoretical bore Alésage théorique max. 54.28 mm Stroke Course 54 mm Cooling system
125cc RL-C TaG FEATURES - CARACTERISTIQUES. Cylinder volume Volume du cylindre cm³. Bore Alésage. 54 mm
125cc RL-C TaG FEATURES - CARACTERISTIQUES Cylinder volume Volume du cylindre 123.67 cm³ Bore Alésage 54 mm Max. theoretical bore Alésage théorique max. 54.28 mm Stroke Course 54 mm Cooling system Système
Cylinder volume Volume du cylindre. Bore Alésage. Stroke Course. RPM limiter Limiteur de régime
125cc RL-C TaG FEATURES - CARACTERISTIQUES Cylinder volume Volume du cylindre 123.67 cm³ Bore Alésage 54 mm Max. theoretical bore Alésage théorique max. 54.28 mm Stroke Course 54 mm Cooling system Système
Cylinder volume Volume du cylindre. Bore Alésage. Stroke Course. RPM limiter Limiteur de régime
125cc RL-C TaG FEATURES - CARACTERISTIQUES Cylinder volume Volume du cylindre 123.67 cm³ Bore Alésage 54 mm Max. theoretical bore Alésage théorique max. 54.28 mm Stroke Course 54 mm Cooling system Système
B - Cadet 125cc RL - F - TaG
B - Cadet 125cc RL - F - TaG FEATURES CARACTERISTIQUES Cylinder volume Volume du cylindre 123.67 cm³ Bore Alésage 54 mm Max. theoretical bore Alésage théorique max. 54.28 mm Stroke Course 54 mm Cooling
WATERSWIFT 60cc - TaG
WATERSWIFT 60cc - TaG FEATURES - CARACTERISTIQUES Cylinder volume Volume du cylindre 59.17 cm³ (60.00 cm³ max) Bore Alésage 41.81 mm Max. theoretical bore Alésage théorétique max. 42.10 mm Stroke Course
60cc Mini Swift PROMOTIONAL - TaG
60cc Mini Swift PROMOTIONAL - TaG FEATURES - CARACTERISTIQUES Cylinder Volume Volume du cylindre 59.00 cm³ Bore Alésage 41.80 mm Max. theoretical bore Alèsage théoretique max. 42.10 mm Stroke Course 43
X30 ROOKIE 60cc FEATURES - CARACTERISTIQUES. Cylinder volume Volume du cylindre cm³. Bore Alésage mm
X30 ROOKIE 60cc FEATURES - CARACTERISTIQUES Cylinder volume Volume du cylindre 59.45 cm³ Bore Alésage 41.81 mm Max. theoretical bore Alésage théorique max. 42.00 mm Stroke Course 43.30 mm Cooling system
COMMISSION INTERNATIONALE DE KARTING - FIA
VARIANTES OPTIONS À LA FICHE D'HOMOLOGATION OPTION VARIANTS TO THE HOMOLOGATION FORM Homologation N COMMISSION INTERNATIONALE DE KARTING - FIA Constructeur : Manufacturer: Tony Kart s.r.l. Adresse : Address:
NATIONAL HOMOLOGATION FORM KARTING ENGINE X30 SUPER - TAG
NATIONAL HOMOLOGATION FORM KARTING ENGINE X30 SUPER - TaG Manufacturer IAME S.P.A - ZINGONIA Make IAME Model X30 SUPER - TAG Validity of the homologation 6 years Number of pages 51 This Homologation Form
X30 SHIFTER 125cc TaG (2011)
X30 SHIFTER 125cc TaG (2011) FEATURES - CARACTERISTIQUES Cylinder volume Volume du cylindre 124.08 cm³ Bore Alésage 53.89 mm Max. theoretical bore Alésage théorique max. 54.08 mm Stroke Course 54.40 mm
Cylinder volume Volume du cylindre. Bore Alésage. Stroke Course
FEATURES - CARACTERISTIQUES Cylinder volume Volume du cylindre 174.56 cm³ (Max 175.5 cm³) Bore Alésage 63.92 mm Max. theoretical bore Alésage théorique max. 64.06 mm Stroke Course 54.40 mm Distance between
Cylinder volume Volume du cylindre. Bore Alésage. Stroke Course
FEATURES - CARACTERISTIQUES Cylinder volume Volume du cylindre 174.56 cm³ (Max 176.6 cm³) Bore Alésage 63.90 mm Max. theoretical bore Alésage théorique max. 64.26 mm Stroke Course 54.40 mm Distance between
FEDERATION INTERNATIONALE DE L'AUTOMOBILE
FEDERATION INTERNATIONALE DE L'AUTOMOBILE JHomojoçjatio^ FICHE D'HOMOLOGATION POUR MOTEUR DE FORMULE 3 HOMOLOGATION FORM FOR FORMULA 3 ENGINE Véhicule : Constructeur et type Vehicle: Manufacturer Adam
60cc RL FEATURES - CARACTERISTIQUES. Cylinder volume Volume du cylindre cm³ (60.00 cmᵌ max) Bore Alésage mm
60cc RL FEATURES - CARACTERISTIQUES Cylinder volume Volume du cylindre 59.45 cm³ (60.00 cmᵌ max) Bore Alésage 41.81 mm Max. theoretical bore Alésage théorique max. 42.00 mm Stroke Course 43.30 mm max Cooling
X30 SHIFTER 125cc TaG
X30 SHIFTER 125cc TaG FEATURES - CARACTERISTIQUES Cylinder volume Volume du cylindre 124.08 cm³ Bore Alésage 53.89 mm Max. theoretical bore Alésage théorique max. 54.08 mm Stroke Course 54.40 mm Distance
ENGINE 108H. Manufacturer. TORINI MOTOR CO., LTD. Make. TORINI Model. TRE220 UPDATE (to TC250) Validity of the homologation 6 years Number of pages 31
ENGINE Manufacturer TORINI MOTOR CO., LTD. Make TORINI Model TRE220 UPDATE (to TC250) Validity of the homologation 6 years Number of pages 31 This Homologation Form reproduces descriptions, illustrations
SHIFTER 125cc TaG. Cylinder volume Volume du cylindre. Bore Alésage. Stroke Course. Selettra ignition Allumage Selettra
SHIFTER 125cc TaG FEATURES - CARACTERISTIQUES Cylinder volume Volume du cylindre 124.08 cm³ Bore Alésage 53.89 mm Max. theoretical bore Alésage théorique max. 54.08 mm Stroke Course 54.40 mm Distance between
Cylinder volume Volume du cylindre. Bore Alésage. Stroke Course. Selettra ignition Allumage Selettra
125cc TaG FEATURES - CARACTERISTIQUES Cylinder volume Volume du cylindre 124.08 cm³ Bore Alésage 53.89 mm Max. theoretical bore Alésage théorique max. 54.08 mm Stroke Course 54.40 mm Distance between conrod
PNEUMATIQUE / TYRE COMMISSION INTERNATIONALE DE KARTING - FIA FICHE D HOMOLOGATION HOMOLOGATION FORM 69/P/13
FICHE D HOMOLOGATION HOMOLOGATION FORM Homologation N 69/P/ COMMISSION INTERNATIONALE DE KARTING - FIA PNEUMATIQUE / TYRE Manufacturier Tyre Manufacturer VEGA S.p.A. Marque Make VEGA Modèle Model SLICK
COMMISSION INTERNATIONALE DE KARTING - FIA
FICHE D HOMOLOGATION HOMOLOGATION FORM Homologation N 3/P/ COMMISSION INTERNATIONALE DE KARTING - FIA PNEUMATIQUE / TYRE Manufacturier Tyre Manufacturer Reifenwerk Heidenau GmbH Marque Make MOJO Modèle
NATIONAL HOMOLOGATION FORM KARTING ENGINE
NATIONAL HOMOLOGATION FORM KARTING ENGINE Manufacturer TORINI MOTOR CO., LTD. Make TORINI Model CLUBMAXX 210 (TC210) Validity of the homologation 6 years Number of pages 34 Homologation N This Homologation
NATIONAL HOMOLOGATION FORM KARTING ENGINE
NATIONAL HOMOLOGATION FORM KARTING ENGINE Manufacturer TORINI MOTOR CO., LTD. Make TORINI Model TC250 (PREVIOUSLY TRE220) UPDATE Validity of the homologation 6 years Number of pages 35 This Homologation
NATIONAL HOMOLOGATION FORM - ENGINE
NATIONAL HOMOLOGATION FORM - ENGINE Homologation N Manufacturer VORTEX Make DVS JNR Model 125CC Validity of the homologation 10 years Number of pages 30 This Homologation Form reproduces descriptions,
Note: Registration does not imply or guarantee use in a class
1 Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classes must be applied for after Homologation and Registration approvals ENGINE Manufacturer
Manufacturer Address Engine # IAME S.p.A. Via Lisbona, ZINGONIA (ITALY) X30 125cc RL-C TaG. Number of pages 22 PICTURE OF ENGINE
Manufacturer Address Engine # IAME S.p.A. Via Lisbona, 15 24040 ZINGONIA (ITALY) TAG RACING INTERNATIONAL TM Manufacturer IAME S.P.A. - ZINGONIA (I) Make PARILLA Model X30 125cc RL-C TaG Inlet type REED
1 Informations générales : 1.1 Créateur SUBARU Karting. 1.3 Marque et modèle. 1.4 Cylindrée. 1.5 Photos FICHE HOMOLOGATION MOTEUR KART SUBARU KX-21
FICHE HOMOLOGATION MOTEUR KART SUBARU KX-21 MOTOR KART SUBARU KX-21 HOMOLOGATION FORM 1 Informations générales : 1.1 Créateur SUBARU Karting OF COURSE SARL 1.2 Fabriquant 1.3 Marque et modèle FUJI HEAVY
ENGINE. IAME SPA IAME KA cc REEDJET AUS TaG 6 Years 28
ENGINE Manufacturer Make Model Validity of the homologation Number of pages IAME SPA IAME KA 100-100cc REEDJET AUS TaG 6 Years 28 This Homologation Form reproduces descriptions, illustrations and dimensions
HOMOLOGATION OF KART ENGINE PROVISIONAL
HOMOLOGATION OF KART ENGINE Category MSA Cadet Manufacturer IAME Model Parilla Gazelle 60cc U.K. Valid From 01 January 2013 Number of pages of main fiche 16 This Homologation Form reproduces descriptions,
NATIONAL HOMOLOGATION FORM - ENGINE
NATIONAL HOMOLOGATION FORM - ENGINE Homologation N Manufacturer VORTEX Make MINI ROK Model 60CC Validity of the homologation 6 years Number of pages 32 This Homologation Form reproduces descriptions, illustrations
HOMOLOGATION OF KART ENGINE
HOMOLOGATION OF KART ENGINE Category IAME X30 JUNIOR & SENIOR Manufacturer IAME Model X30 125cc RL TaG - UK Valid From 01 January 2014 Number of pages 20 This Homologation Form reproduces descriptions,
FEDERATION INTERNATIONALE DE L AUTOMOBILE
FEDERATION INTERNATIONALE DE L AUTOMOBILE 06.03.2017 FICHE DE PRESENTATION DES SYSTEMES D EXTINCTION FIXES (NORME FIA 8865-2015) PRESENTATION FORM FOR PLUMBED-IN FIRE EXTINGUISHER SYSTEMS (FIA STANDARD
FEDERATION INTERNATIONALE DE L AUTOMOBILE
FEDERATION INTERNATIONALE DE L AUTOMOBILE Date 30.11.2015 FICHE DE PRESENTATION DES SYSTEMES D EXTINCTION FIXES (NORME FIA 8865-2015) PRESENTATION FORM FOR PLUMBED-IN FIRE EXTINGUISHER SYSTEMS (FIA STANDARD
FEDERATION INTERNATIONALE DE L AUTOMOBILE
FEDERATION INTERNATIONALE DE L AUTOMOBILE Date 05.12.2016 FICHE DE PRESENTATION DES SYSTEMES D EXTINCTION FIXES (NORME FIA 8865-2015) PRESENTATION FORM FOR PLUMBED-IN FIRE EXTINGUISHER SYSTEMS (FIA STANDARD
FICHE TECHNIQUE DU PNEUMATIQUE TYRE TECHNICAL FORM
FICHE TECHNIQUE DU PNEUMATIQUE TYRE TECHNICAL FORM Manufacturier Tyre Manufacturer VEGA S.p.A. Marque Make VEGA Modèle Model SLICK SL 0x4.60-5 Nombre de pages Number of pages 4 PHOTO DU PNEU MONTÉ SUR
FEDERATION INTERNATIONALE DE L'AUTOMOBILE JAPAN AUTOMOBILE FEDERATION. Groupe Group A / B
FEDERATION INTERNATIONALE DE L'AUTOMOBILE JAPAN AUTOMOBILE FEDERATION Groupe Group A / B Homologation N JAF JA-215 JAF 200741 FICHE D'HOMOLOGATION CONFORME A L'ANNEXE J DU CODE SPORTIF INTERNATIONAL HOMOLOGATION
ENGINE. Manufacturer IAMEs.p.a. Category. Homologation Period. Pages 16. Model, Type SIGNATURE AND STAMP OF AKA SIGNATURE AND STAMP OF APPLICANT
1 ENGINE Manufacturer IAMEs.p.a. Category Make Model, Type PARILLA Leopard X30 125cc RL - TaG - AUS Homologation Period Pages 16 This homologation sheet reproduces description, illustrations and dimensions
NATIONAL HOMOLOGATION FORM
NATIONAL HOMOLOGATION FORM Homologation N ENGINE Manufacturer BRIGGS & STRATTON Make ANIMAL Model 124332 Validity of the homologation 6 years Number of pages 27 This Homologation Form reproduces descriptions,
SN SN 600 SN SN 300
SNG 500 - SNG 600 SNU 500 - SNU 600 SNA 500 - SNA 600 SN 500 - SN 600 SN 200 - SN 300 SD 3100 SD 3000 114 DISPOSITIFS D'ÉTANCHÉITÉ - SEALING ARRANGEMENTS Joint en polyuréthane TSNG pour: SNG-SNU TSNG polyurethan
NATIONAL HOMOLOGATION FORM KARTING ENGINE
NATIONAL HOMOLOGATION FORM KARTING ENGINE Manufacturer BRIGGS & STRATTON Make BRIGGS & STRATTON Model 206-124332 Validity of the homologation 6 years Number of pages 25 This Homologation Form reproduces
CARACTERISTIQUES TECHNIQUES TECHNICAL CHARACTERISTICS 365/80 R 20 XZL TL 152 K MPT
Ref. AA110081 CARACTERISTIQUES TECHNIQUES TECHNICAL CHARACTERISTICS PLE/T - PLE/M - Département Poids Lourd - Truck Tire Department Ref. SA110081 Charge en simple 152 3550 kg Charge en jumelé kg Vitesse
ILLUSTRATED PARTS MANUAL/ MANUEL DE PIÈCES DÉTACHÉES
ILLUSTRATED PARTS MANUAL/ MANUEL DE PIÈCES DÉTACHÉES 208cc ZS 370-SUB Horizontal Shaft OHV Snow Engine Moteurs de 208 cm3 ZS 370-SUB à arbre horizontal et soupapes en tête MTD Products Ltd., P. O. Box
FEDERATION INTERNATIONALE DE L AUTOMOBILE. Groupe GT1. Group
FEDERATION INTERNATIONALE DE L AUTOMOBILE Groupe Group GT1 FICHE D'HOMOLOGATION CONFORME A L'ANNEXE J DU CODE SPORTIF INTERNATIONAL HOMOLOGATION FORM IN ACCORDANCE WITH APPENDIX J OF THE INTERNATIONAL
FITTING INSTRUCTIONS FOR RSET12BK ADJUSTABLE REARSETS FOR TRIUMPH DAYTONA 675 ( )
FITTING INSTRUCTIONS FOR RSET12BK ADJUSTABLE REARSETS FOR TRIUMPH DAYTONA 675 (2008-2011) First remove the original Triumph rearsests. Then remove the engine axle and insert it from the otherside (from
334A or 334AB. Number of piston rings 1 Number of exhaust ports 2. Big end conr. Ball-bearing diam. 18X24X15 Combustion chamber shape Spherical
125cc LEOPARD FEATURES Cylinder volume 123.67 cc Bore 54 mm Max. theoretical bore 54.28mm Stroke 54mm Cooling system Water Inlet system Reed valve Number of carbs 1 Tillotson HL Carb. 334A or 334AB Cylinder/crankcase
View thousands of Crane Specifications on FreeCraneSpecs.com LTM Mobile Crane Grue mobile. Technical Data Caractéristiques techniques
Mobile Crane Grue mobile LM 1350-6.1 echnical Data Caractéristiques techniques able of content ables des matières echnical Data Dimensions 3 Boom/jib combinations 4 7 Weights, Working speeds 8 on telescopic
ILLUSTRATED PARTS MANUAL/ MANUEL DE PIÈCES DÉTACHÉES
ILLUSTRATED PARTS MANUAL/ MANUEL DE PIÈCES DÉTACHÉES 277cc ZS 78-SU Horizontal Shaft OHV Snow Engine Moteurs de 277 cm3 ZS 78-SU à arbre horizontal et soupapes en tête MTD Products Ltd., P. O. Box 1386,
FEDERATIG IN INTERNATIONALE DE L AUTOMOBILE JAPAN AUTOMOBILE FEDERATION 0 1 MARS FIA Homologation No. H :2 s: ^
FEDERATION INTERNATIONALE DE L AUTOMOBILE JAPAN AUTOMOBILE FEDERATION H :2 s: ^ 00 3 Groupe S U P E R T O U R I S M E Group S U P E R T O U R I N G JS-006 TfA-157)------ JAF%^^^ B 1 9 9 Æ 1 H.91n FICHE
VW FUN CUP ANNEXE III Pour les moteurs essence EVO3
A) Voiture vue de 3/4 avant B) Voiture vue de 3/4 arrière Car seen from 3/4 front Car seen 3/4 rear PHOTO A INSERER PHOTO A INSERER 1. GENERALITES / GENERAL 101. Constructeur Manufacturer W RACING TEAM
TM &P-2 TECHNICAL MANUAL
TM 5-2410-234-14&P-2 TECHNICAL MANUAL OPERATOR S, ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE MANUAL (INCLUDING REPAIR PARTS INFORMATION AND SUPPLEMENTAL MAINTENANCE AND REPAIR PARTS
100cc REEDJET USA TaG
100cc REEDJET USA TaG FEATURES Cylinder Volume 100 cm³ max Bore 48.20 mm Max. theoretical bore 48.53 mm Stroke 54.05 mm max Cooling system Air Inlet system Reed valve Number of carbs 1 Tillotson Carburettor
VersaWall SlimLine 1750
Index Stick built curtain wall 1 3/4"(44.5mm) profile Mur rideau avec profilé de 1 3/4"(44.5mm) Capped Couvercles à enclenchement Primary components - back sections Composantes principales - traverses
HIRTH MOTOREN ~Ei EL45/82R4. HIRTH Engine Moteur HIRTH. Spare Parts List Liste de pieces de rechange
HIRTH MOTOREN ~Ei 7141 BENNINGENt NECKAR KREIS LUDWIG SB URG WEST GERMANY EL45/8R4 HIRTH Engine Moteur HIRTH Spare Parts List Liste de pieces de rechange plate tableau 148 picturo quantity part numbor
Index. Primary components - back sections Composantes principales - traverses ou meneaux
Thermally broken Split mullion curtain wall - Capped and SSG 2 /2" (63.5mm) profile. Available in 5 /4"(33.4mm) and 6 5/8"(68.3mm) depths. Mur-rideau à meneaux en deux sections avec bris thermique.vss
SEA-DOO SPECIFICATION BOOKLET MANUEL DE CARACTÉRISTIQUES 988-003 (Smt003-00a_intro.fm SH) Were added: 003 models 003 EDITION DIFFERENCES WITH 988-00 Were revised: minor corrections were done as per latest
rev 1_ MH-246.4DS
rev 1_02-10-15 MH-246.4DS 1 Shaft, Handle, Cutting Attachment 16 9 7 1 8 6 38 11 15 10 3 2 218 4 37 2 1 Shaft, Handle, Cutting Attachment 1 1 660195626 LOOP HANDLE SET POIGNÉE CPL. 1 INC. 6-9,16 1 2 326036-4
All Terrain crane 90 tons
All Terrain crane tons liebherr ltm /1 BOOM LENGTHS: to JB LENGTHS: to JB OFFSETS: - - NOTES: portland office:.8.1 seattle office: 8 Technical Data Caractéristiques techniques LTM/1 Mobile Crane Grue automotrice
VW FUN CUP ANNEXE III - REVISION 01 ( ) Pour les moteurs essence EVO3
A) Voiture vue de 3/4 avant B) Voiture vue de 3/4 arrière Car seen from 3/4 front Car seen 3/4 rear PHOTO A INSERER PHOTO A INSERER 1. GENERALITES / GENERAL 101. Constructeur Manufacturer W RACING TEAM
USA SUPER SHIFTER 175cc
USA SUPER SHIFTER 175cc FEATURES Cylinder volume 174.46 cm³ (Max 176.6 cm³) Bore 63.90 mm Max. theoretical bore 64.26 mm Stroke 54.40 mm Distance between conrod centers 115 mm Cooling system Water Inlet
255/100 R 16 XZL TL 126 K
page : A DOSSIER DE CARACTERISTIQUES TECHNIQUES PRODUIT TECHNICAL CHARACTERISTICS PRODUCT FILE Rédacteur : Valideur T : Valideur M : Y. MAGNAUDEIX A. CARLONI L. MOZZICONACCI Tous les renseignements figurant
ILLUSTRATED PARTS MANUAL/ MANUEL DE PIÈCES DÉTACHÉES
ILLUSTRATED PARTS MANUAL/ MANUEL DE PIÈCES DÉTACHÉES 140 cc 5T65RU OHV Vertical Shaft Engine Moteurs de 140 cm3 5T65RU à arbre vertical MTD Products Ltd., P. O. Box 1386, KITCHENER, ONT. N2G 4J1 PRINTED
A110 - ENGINES REFECTION PARTS. A G 1108cc 1100VB bore/stroke 70x72. A cc bore/stroke 71,2 x 72
Page 1 A110 - ENGINES REFECTION PARTS A110 1100G 1108cc 1100VB bore/stroke 70x72 Set of liners and cast pistons Forged racing piston wtih rings (1 + 1,5 + 2,8 ) Original cast piston Cast iron liner Set
Motorsport South Africa
Motorsport South Africa SOUTH AFRICAN KARTING COMMISSION HOMOLOGATION SCHEDULE MAXTERINO MX-60 Version 1 2017-01-25 MSA Ref. Manufacturer MAXTER S.R.L. Distributor Ed Murray Racing cc Model Maxterino Period
ZAZERI 48" ZAZERI 60"
Installation alcôve A et installation en coin B Built-in A and corner B installation ZAZERI " ZAZERI 60" ZITTACLEAN " (5 / "~6 /6") (5mm~77mm) 60" (57 7/6"~5 5/" ) (59mm~9mm) "(9 /"~0 /") (75mm~77mm )
FÉDÉRATION INTERNATIONALE DE L AUTOMOBILE
IT S A. Z h o t f n t t a G r 3 FÉDÉRATION INTERNATIONALE DE L AUTOMOBILE,flC H E DîHj^pLOGATION CONFORME A L ANNEXE J DU CODE SPORTIF INTERNATIONAL POUR LES VOITURES DES GROUPES 1 A 5 BOOK OF RECOGNITION
BARBECUES ADELAÏDE : WOODY - WOODY L - CLASSIC - CLASSIC L & CLASSIC L DELUXE
ADELAÏDE 2 WOODY ADELAÏDE ADELAÏDE 2 CLASSIC L DELUXE ADELAÏDE ADELAÏDE L ADELAÏDE 3 CLASSIC L ADELAÏDE 3 CLASSIC L DELUXE ADELAÏDE ADELAÏDE ADELAÏDE 4 CLASSIC L DELUXE Grids and griddles : important information
PARILLA LEOPARD RL 125 TECHNICAL SPECIFICATIONS
PARILLA LEOPARD RL 125 VERSION 4 / 2012 UPDATED September 6 th, 2012 DOCUMENT UPDATE SCHEDULE It is certified that the updates listed below have been approved by the Australian Karting Association and
Mobile Crane/Grue mobile LTM
Mobile Crane/Grue mobile LM 1090-4.2 Preliminary Préliminaire ALL-ROUNDER Ready for anything max ft 110 USt 197 ft 203 ft ft 249 ft Mobile Crane/Grue mobile LM 1090-4.2 197 ft NZK K 31 ft 52 ft m 8.4 ft
ThermaWall 2600 Primary components - back sections Composantes principales - traverses ou meneaux
Primary components - back sections Composantes principales - traverses ou meneaux CAPPED DOUBLE GLAZED SYSTEM MULLIONS MENEAUX DU SYSTÈME À COUVERCLES À ENCLENCHEMENT ET À DOUBLE VITRAGE 25759 25754 25774
NATIONAL HOMOLOGATION FORM ENGINE
NATIONAL HOMOLOGATION FORM ENGINE Manufacturer VORTEX Make MINI ROK Model 60CC Validity of the homologation 6 years Number of pages 40 This Homologation Form reproduces descriptions, illustrations and
45.06 Fuel Refer Chapter 22 Fuel, as run, to comply with tests under chapter 22.01
CHAPTER 45 PARILLA LEOPARD 125cc and PARILLA LEOPARD X30 125cc Preamble It is expected that this class will continue to evolve during its early life and the promoters of the class reserve the right to
FEDERATION INTERNATIONALE DE L AUTOMOBILE. Groupe Group
FEDERATION INTERNATIONALE DE L AUTOMOBILE T ^» - U 5 6 Groupe Group T4 Camions Tout-Terrain Cross-Country trucks FICHE D'HOMOLOGATION CONFORME A L'ANNEXE J DU CODE SPORTIF INTERNATIONAL HOMOLOGATION FORM
JUNIOR-ROK 2014 Specification Sheet /A Dated 01/01/2014
IDENTIFICATION SHEET This Identification Sheet reproduces descriptions, illustrations and dimensions of the JUNIOR ROK engine to be used in the JUNIOR ROK CUP CLASS in South Africa BOTH ENGINES WITH VORTEX
INSTRUMENTATION D'ALÉSAGE DRILLING INSTRUMENTS
INSTRUMENTATION D'ALÉSAGE DRILLING INSTRUMENTS 500200 Instrumentation d alésage pour clou centromédullaire Désignation / Product description Qté. / Quntity 141 500200B Boîte vide avec un plateau / Empty
FITTING INSTRUCTIONS FOR CP0404BL/WH NO-CUT AERO CRASH PROTECTORS HUSQVARNA 701 ENDURO/SUPERMOTO 2016-
FITTING INSTRUCTIONS FOR BL/WH NO-CUT AERO CRASH PROTECTORS HUSQVARNA 701 ENDURO/SUPERMOTO 2016- Page 1 PICTURE A PICTURE B REAR OF BIKE FRONT OF BIKE PICTURE C THIS KIT CONTAINS THE ITEMS PICTURED AND
WEAVEBIRD LOOM TROUBLE SHOOTING GUIDE
1573 Savoie C. P. 4 Plessisville, Qc. G6L 2Y6 TEL: 819-362-7207 FAX: 819-362-2045 www.leclerclooms.com info@leclerclooms.com WEAVEBIRD LOOM TROUBLE SHOOTING GUIDE If you have problems when starting the
avvolgitori ENRUBANNEUSES WRAPPERS
avvolgitori ENRUBANNEUSES WRAPPERS abs 15 p Versione portata (a sollevamento) senza braccio di carico e scarico. Version portée sans bras de chargement et déchargement. Carried version without loading
CONVERTISSEURS CATALYTIQUES HOMOLOGUES PAR LES ASN CATALYTIC CONVERTERS HOMOLOGATED BY THE ASNs LISTE TECHNIQUE N 8 / TECHNICAL LIST N 8.
CONVERTISSEURS CATALYTIQUES HOMOLOGUES PAR LES ASN CATALYTIC CONVERTERS HOMOLOGATED BY THE ASNs LISTE TECHNIQUE N 8 / TECHNICAL LIST N 8 Les copies des fiches d'homologation sont disponibles auprès des
Index. ThermaWall Thermally broken curtain wall - Capped and SSG 2 1 2"(63.5mm) profile SSG. Capped
Thermally broken curtain wall - Capped and SSG 2 2"(63.5mm) profile Mur-rideau à bris thermique - Système VSS ou couvercles à enclenchement. Profilé de 2 2"(63.5mm) Index Capped Couvercles à enclenchement
Fitting Instructions for RSET14BK Adjustable Rearsets Aprilia RSV4R and Factory ( 09-)
Fitting Instructions for RSET4BK Adjustable Rearsets Aprilia RSV4R and Factory ( 09-) First remove the original Aprilia rearsests. Install on the gear shaft connector () onto the gear shaft. Then connect
PARILLA LEOPARD X TECHNICAL SPECIFICATIONS
PARILLA LEOPARD X30 125 VERSION 7 / 2013 UPDATED JULY 16 th, 2013 DOCUMENT UPDATE SCHEDULE It is certified that the updates listed below have been approved by the Australian Karting Association and have
X30 CHALLENGE TECHNICAL REGULATIONS 2017/2018 VER 1.0
X30 CHALLENGE TECHNICAL REGULATIONS 2017/2018 VER 1.0 NAME OF EVENT: ORGANIZER: PROMOTER: TITLE SPONSOR: X30 Challenge Ras Al Khaimah Kart Track (RAK TRACK) Emirates Karting Ras Al Khaimah Economic Zone
II HIRTH MOTOREN 1-- TOUTES GAMMES CONFONDUES / ALL RANGES
www.sasic.com FLASH INFO 01.2018 R E N A U L T C A P T U R 4 6 R E F E R E N C E S TOUTES GAMMES CONFONDUES / ALL RANGES Galet accessoire Galet tendeur Alt. 1624009 Alternator tensioner OE 117509654R Acc.
Schick electronic SA presents. The new concept of frontal detection SP2-115
Schick electronic SA presents The new concept of frontal detection SP2-115 The SP2-115 benefits The costs are reduced from 30% comparing to traditional parking guidance system An all-in-one product! (sensor
FITTING INSTRUCTIONS FOR CP0393BL AERO CRASH PROTECTORS SUZUKI GSX-S
Page1 FITTING INSTRUCTIONS FOR BL AERO CRASH PROTECTORS SUZUKI GSX-S 1000 2015- PICTURE A PICTURE B REAR OF BIKE FRONT OF BIKE PICTURE C THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT
MSA COMER C50 TECHNICAL REGULATIONS 2019 VERSION 2
MSA COMER C50 TECHNICAL REGULATIONS 2019 VERSION 2 Category Bambino Manufacturer Comer Spa Model C50 Valid from 01 January 2019 Number of pages 8 This Homologation Form reproduces descriptions, illustrations
Pièces de rechange Spare parts list KE00**01** FAUCHEUSE BROYEUSE BRUSH CUTTER
Pièces de rechange Spare parts list KE00**01** FAUCHEUSE BROYEUSE BRUSH CUTTER k501040002_c 07/04/2015 25 11 26 18 41 41 23 4 30 7 19 35 31 14 10 13 20 3 1 21 40 2 42 16 37 33 29 8 22 29 26 32 37 34 23
RYOBI Item No. RY9C3501 Mfg. No Replacement Parts List
RYOBI Item No. RYC0 Mfg. No. 000 Replacement Parts List 000 -- (REV:0) TECHTRONIC INDUSTRIES POWER EQUIPMENT Pearman Dairy Road Anderson, SC USA -00-0-00 RYOBI GENERATOR RYC0 0 SEE FIG. B Voir la figure
7 SUBSIDIARIES 70 COUNTRIES 125 MLN MOTOVARIO KEY FIGURES LOGISTIC ITALY HEADQUARTER ITALY PRODUCTION FOUNDATION HOURS ON 24 SQM OF
CORPORATE &PRODUCTS MOTOVARIO KEY FIGURES 1965 FOUNDATION more than 70 COUNTRIES over 600 EMPLOYEES WORLDWIDE PRODUCTION 24 HOURS ON 24 50.000 SQM OF PRODUCTION PBH VSF H B S D M 7 SUBSIDIARIES 125 MLN