MID-MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE NZM SERIES 3

Transcription

1 Parts Manual for MID-MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE NZM SERIES 3 MODEL NZM19483KWV NZM21523KWV NZM25523KWV NZM25613KWV NZM27613KH McDonough, GA, U.S.A. COPYRIGHT 2006 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision IR, 7/21/2006 Manual No

2

3 Table Of Contents PAGE GROUP 4 CASTER WHEEL ASSEMBLY 6 DRIVE TIRE & WHEEL ASSEMBLY 8 FRONT FRAME ASSEMBLY (Frame) 12 FRONT FRAME ASSEMBLY (Deck Lift) 14 REAR FRAME & TANK BRACKETS 16 FUEL TANK ASSEMBLY 18 TWIN STICK CONTROL ASSEMBLY (R.H. Side) 22 TWIN STICK CONTROL ASSEMBLY (L.H. Side) 26 PARKING BRAKE ASSEMBLY 28 HYDRO PUMP ASSEMBLIES 30 HOSE ASSEMBLY (48" & 52" Deck) 32 HOSE ASSEMBLY (61" Deck) 34 HYDRO RESERVOIR ASSEMBLY 36 HYDRO IDLER ASSEMBLY 38 ENGINE SUB-ASSEMBLY 40 SEAT ASSEMBLY 42 MUFFLER GUARD ASSEMBLY 44 48" CUTTING DECK ASSEMBLY (Sub Assy) 46 48" CUTTING DECK ASSEMBLY (Final Assy) 48 52" CUTTING DECK ASSEMBLY (Sub Assy) 50 52" CUTTING DECK ASSEMBLY (Final Assy) 52 61" CUTTING DECK ASSEMBLY (Sub Assy) 54 61" CUTTING DECK ASSEMBLY (Final Assy) 56 IDLER ASSEMBLIES 58 DECK SPINDLE ASSEMBLIES 60 DECALS 62 CONTROL PANEL ASSEMBLY 64 ROLL BAR PROTECTIVE STRUCTURE 66 ELECTRICAL COMPONENTS 68 WIRING HARNESS (Kawasaki Engines) 70 WIRING HARNESS (Kohler Engines) 72 WIRING SCHEMATIC (Kawasaki Engines) 74 WIRING SCHEMATIC (Kohler Engines) MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 3 Manual No

4 CASTER WHEEL ASSEMBLY Manual No MID-MOUNT Z-RIDER ZERO TURNING 4 SERIES 3

5 CASTER WHEEL ASSEMBLY Item Part No Qty Description Note WELDMENT, Caster Yoke 1A WELDMENT, Caster Yoke, 7-1/4 Wide used on 61 Deck Model only SCREW, 1/2-13 x 7 Hex Head Cap, GR 5 2A SCREW, 1/2-13 x 9-1/2 Hex Head Cap, GR 5 used on 61 Deck Model only NUT, 1/2-13 Hex Nyloc SPACER, Bearing, 5.29 Long 4A SPACER, Bearing, 7.29 Long used on 61 Deck Model only ASSY, Tire & Wheel 13 x (Incl. item 6, 7, 8, 9 & 10) used on 48 & 52 Deck Models only 5A ASSY, Tire & Wheel 13 x (Incl. item 6A, 7A, 8, 9 & 10) used on 61 Deck Model only WELDMENT, Wheel Hub & Rim 13 x (gray) 6A WELDMENT, Wheel Hub & Rim 13 x (gray) used on 61 Deck Model only TIRE, 13 x Ply Smooth 7A TIRE, 13 x , 4PR Smooth BALL BEARING, Heim.750 Heim Unibal # RF AP FITTING, 1/4-28 Lube Tapered Head w/ball Check AIR VALVE STEM & Cap Goodyear # TR-412 or equivalent SPACER Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 5 Manual No

6 DRIVE TIRE & WHEEL ASSEMBLY Manual No MID-MOUNT Z-RIDER ZERO TURNING 6 SERIES 3

7 DRIVE TIRE & WHEEL ASSEMBLY Item Part No Qty Description Note ASSY, Wheel 23 x (Incl. items 2, 3 & 4) used on 48 & 52 Deck Models 1A ASSY, Wheel 24 x (Incl. items 2A, 3A & 4) used on Series 61 Deck Models TIRE, 23 x NHS 4Pr Turf Master TL 2A TIRE, 24 x 12-12HHS 49R Turf Master RIM, 12 x /4.5 AG Silver 237 3A RIM, 12 x /4.5 RAW AIR VALVE STEM & Cap Goodyear # TR-412 or equivalent LUG BOLT, 1/2-20 UNF x 7/ DRUM, Brake (Ausco) PIN, 9/64 x 1-1/2 Cotter included as part of wheel motor KEY, #11 Woodruff included as part of wheel motor NUT, 3/4-20 Slotted Hex included as part of wheel motor Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 7 Manual No

8 FRONT FRAME ASSEMBLY (Frame) Manual No MID-MOUNT Z-RIDER ZERO TURNING 8 SERIES 3

9 FRONT FRAME ASSEMBLY (Frame) Item Part No Qty Description Note WELDMENT, Front Frame 2 2 GROUP, Front Wheel (ref: Caster Wheel Assembly Page) GREASE SEAL BEARING, Tapered Roller (tapered roller brg.) & (inner race) SPACER, Jackstaff CASTLE NUT, 1-1/ UNF, GR B ROLL PIN, 3/16 x 1-1/ CAP, Dust BOLT, 1/2-13 x 1-1/2 Square Neck Carriage Grade NUT, 1/2-13 Hex Nyloc BUSHING, Teflon PAD, Floor Pan EYEBOLT, 3/8-16 x NUT, 3/8-16 Hex Nyloc SPRING, Extension, Lift Assist SPACER, Lift Adjust (1.08 Long) SPACER, Lift Adjust (1.43 Long) WELDMENT, Height Adjust SCREW, 3/8-16 x 2-1/2 Hex Head Cap, GR BRACKET, Deck Lift Detent BOLT, 3/8-16 x 1 Square Neck Carriage GR CLIP, Roll Pin, 1/ WASHER,.77 I.D. Flat RING, 3/4 External Retaining FLOOR PAN (Detached) MAT, Floor Pan RING,.375 Diameter External Retaining LUBE FITTING, 3/16 or , 1/4-28 Straight Lube Fitting WELDMENT, Deck Lift Handle SPRING, Neutral Return BRACKET, Handle Support ROD, Latch STOP, Latch SCREW, 5/16-18 x 1 Hex Head Cap, GR PIN, 3/32 x 1/2 Cotter or Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 9 Manual No

10 FRONT FRAME ASSEMBLY (Frame) Manual No MID-MOUNT Z-RIDER ZERO TURNING 10 SERIES 3

11 FRONT FRAME ASSEMBLY (Frame) Item Part No Qty Description Note NUT, 5/16-18 Hex Center Lock or WASHER, 3/8 Flat SAE COVER, Plastic BUSHING, 3/8 Plastic ROLLPIN,1/8 x 7/ MAT, Footpan MAT, Footpan Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 11 Manual No

12 FRONT FRAME ASSEMBLY (Deck Lift) Manual No MID-MOUNT Z-RIDER ZERO TURNING 12 SERIES 3

13 FRONT FRAME ASSEMBLY (Deck Lift) Item Part No Qty Description Note NUT, 1/2-13 Hex Flange GR KEY, 3/16 Square x 1-1/ PIN, 5/32 x 1 Cotter PIN, 1/2 x 1-1/8 Clevis SCREW, 1/2-13 x 2 Hex Head Cap, GR ASSEMBLY, Chain & Eyebolt used on 52 Deck Model only 7A CHAIN, 3 Links 7B 2 ASSEMBLY, Rear Linkage (Not a part sale item)(incl. items 22 used on 61 Deck thru 25) SET SCREW, 5/16-18 Square Head Cup Point WELDMENT, Bellcrank Lift WELDMENT, Rear Lift NUT, 1/2-13 Hex Center Lock, GR SWIVEL, Timing Rod (1/2-13 External Thread) BOLT, 5/16-18 x 1 Short Neck Carriage, GR SHIM PLATE BRACKET, Deck Support WASHER, 5/16 Flat NUT, 5/16-18 Hex Nyloc WELDMENT, Front Deck Lift ROD, Timing (1/2-13 Thread) WASHER,.531 I.D. Flat LINK, Front ROD LINK (1/2-13 thread) ROD SWIVEL (1/2-13 thread) NUT, 1/2-13 Hex, GR B WASHER, 1/2 Internal Tooth Lock Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 13 Manual No

14 REAR FRAME & TANK BRACKETS Manual No MID-MOUNT Z-RIDER ZERO TURNING 14 SERIES 3

15 REAR FRAME & TANK BRACKETS Item Part No Qty Description Note 1A WELDMENT, Rear Frame (48 & 52 Deck) 1B WELDMENT, Rear Frame (61 Deck) WELDMENT, Left Hand Fuel Tank Bracket WELDMENT, Right Hand Fuel Tank Bracket BOLT, 3/8-16 x 1 Square Neck Carriage GR NUT, 3/8-16 Hex Nyloc WASHER, 3/8 Flat CLIP, Open 3/8 Cushioned WELDMENT, Right Hand Socket see also on ROLL BAR PROTECTIVE STRUCTURE page WELDMENT, Left Hand Socket see also on ROLL BAR PROTECTIVE STRUCTURE page NUT, 3/8-16 Hex Flange Lock SCREW, 1/2-13 x 1-1/2 Hex Head Cap or (1 long) NUT, 1/2-13 Hex Center Lock, GR 5 or Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 15 Manual No

16 FUEL TANK ASSEMBLY Manual No MID-MOUNT Z-RIDER ZERO TURNING 16 SERIES 3

17 FUEL TANK ASSEMBLY Item Part No Qty Description Note ASSEMBLY, LH Fuel Tank includes: tank ( ) plus items 3, 6, 7, 8 & ASSEMBLY, RH Fuel Tank includes: tank ( ) plus items 3, 6, 7, 9 & ASSEMBLY, Fuel Pickup includes items 4 & ELBOW, 90 Degree TUBE, Pickup GROMMET, Tube Dapco p/n GAGE, Fuel GROMMET, Gage LID, Fuel Tank CAP, 3-1/2 Fuel Kelch p/n SCREW, 7/16-14 x 2 Hex Head Cap, GR WASHER, 1/2 Flat SAE WASHER, 1/4 Flat WASHER, 1/4 Split Lock SCREW, 1/4-20 x 1-1/4 Hex Head Cap, GR SCREW, 5/16-18 x 2-1/2 Hex Head Cap, GR WASHER, 5/16 Flat NUT, 5/16-18 Hex Nyloc BOLT, 3/8-16 x 1 Square Neck Carriage, GR NUT, 3/8-16 Hex Nyloc NUT, 7/16-14 Hex Nyloc CLIP, Open 3/8 Cushioned WELL-NUT, 1/4-20 x 53/64 also shown on SEAT ASSEMBLY page ASSEMBLY, 3-Way Fuel Valve BRACKET, RH HOSE, 1/4 I.D. x 1'-8 Long Fuel (L.H.) HOSE, 1/4 I.D. x 3'-7.5 Long Fuel (R.H.) HOSE, 1/4 I.D. x 1' Long Fuel used on Kawasaki Engine models only HOSE, 1/4 I.D. x 1'-9 Long Fuel used on Kohler Engine models only CLAMP, Fuel Hose CABLE TIE, 7 Long (not shown) BRACKET, Seat Belt, LH see also on ROLL BAR PROTECTIVE STRUCTURE page Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 17 Manual No

18 TWIN STICK CONTROL ASSEMBLY (R.H. Side) Manual No MID-MOUNT Z-RIDER ZERO TURNING 18 SERIES 3

19 TWIN STICK CONTROL ASSEMBLY (R.H. Side) Item Part No Qty Description Note SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap CHANNEL, Mounting also shown on TWIN STICK CONTROL ASSEMBLY (L.H. Side) page SCREW, 1/4-20 x 1 Hex Head Cap GR 5 or WASHER, 1/4 Flat RING, 5/8 External Retaining WASHER,.64 I.D. x.99 O.D. x.05 Flat BUSHING, Teflon Impregnated MOUNTING PLATE, Left Hand Bearing NUT, 1/4-20 Hex Nyloc 10 1 ASSY, Pump Control Linkage (ref. #'s 11, 12, 13) includes 3 items shown below ROD END (5/16-24 thread) NUT, 5/16-24 Hex, GR 5 or B LINKAGE ROD, Pump Control (5/16-24 thread) NUT, 5/16-18 Hex Nyloc WASHER, 5/16 Flat SCREW, 5/16-18 x 1-1/2 Hex Head Cap, GR WELDMENT, Cross Rod BUSHING MOUNT PLATE, Right Hand GRIP, Twin Stick HANDLEBAR, Twin Stick SCREW, 1/4-20 x 1-3/4 Hex Head Cap, GR 5 or BRACKET, Handle Adjustment SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR MOUNTING ARM SPACER,.498 O.D. x long SCREW 3/8-16 x 2 Hex Head Cap, GR 5 or NUT, 3/8-16 Hex Nyloc SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR WELDMENT, Mounting Hub, RH SET SCREW, 5/16-18 x 1/2 Square Head Cup Point KEY, 3/16 Square x 1-1/ NUT, 1/4-20 Hex Center Lock PLATE, Speed Adjuster PLATE, Bushing Mount, RH NUT, 5/16-18 Hex Flange Lock SCREW, 1/4-20 Shoulder Socket Head DAMPENER, Hydraulic Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 19 Manual No

20 TWIN STICK CONTROL ASSEMBLY (R.H. Side) Manual No MID-MOUNT Z-RIDER ZERO TURNING 20 SERIES 3

21 TWIN STICK CONTROL ASSEMBLY (R.H. Side) Item Part No Qty Description Note SCREW, 5/16-18 x 2 Hex Head Cap, GR 5 Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 21 Manual No

22 TWIN STICK CONTROL ASSEMBLY (L.H. Side) Manual No MID-MOUNT Z-RIDER ZERO TURNING 22 SERIES 3

23 TWIN STICK CONTROL ASSEMBLY (L.H. Side) Item Part No Qty Description Note SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap CHANNEL, Mounting SCREW, 1/4-20 x 1 Hex Head Cap GR 5 or WASHER, 1/4 Flat RING, 5/8 External Retaining WASHER,.64 I.D. x.99 O.D. x.05 Flat BUSHING, Teflon Impregnated MOUNTING PLATE, Left Hand Bearing NUT, 1/4-20 Hex Nyloc 10 1 ASSY, Pump Control Linkage (ref. #'s 11, 12, 13) ROD END (5/16-24 thread) NUT, 5/16-24 Hex, GR 5 or B LINKAGE ROD, Pump Control (5/16-24 thread) NUT, 5/16-18 Hex Nyloc WASHER, 5/16 Flat SCREW, 5/16-18 x 1-1/2 Hex Head Cap, GR WELDMENT, Cross Rod BUSHING MOUNT PLATE, Left Hand GRIP, Twin Stick HANDLEBAR, Twin Stick SCREW, 1/4-20 x 1-3/4 Hex Head Cap, GR 5 or BRACKET, Handle Adjustment SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR MOUNTING ARM SPACER,.498 O.D. x long SCREW 3/8-16 x 2 Hex Head Cap, GR 5 or NUT, 3/8-16 Hex Nyloc SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR WELDMENT, Mounting Hub, LH SET SCREW, 5/16-18 x 1/2 Square Head Cup Point KEY, 3/16 Square x 1-1/ NUT, 1/4-20 Hex Center Lock PLATE, Speed Adjuster PLATE, Bushing Mount, LH NUT, 5/16-18 Hex Flange Lock SCREW, 1/4-20 Shoulder Socket Head DAMPENER, Hydraulic Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 23 Manual No

24 TWIN STICK CONTROL ASSEMBLY (L.H. Side) Manual No MID-MOUNT Z-RIDER ZERO TURNING 24 SERIES 3

25 TWIN STICK CONTROL ASSEMBLY (L.H. Side) Item Part No Qty Description Note SCREW, 5/16-18 x 2 Hex Head Cap, GR 5 Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 25 Manual No

26 PARKING BRAKE ASSEMBLY Manual No MID-MOUNT Z-RIDER ZERO TURNING 26 SERIES 3

27 PARKING BRAKE ASSEMBLY Item Part No Qty Description Note RING, 5/8 External Retaining GROOVE PIN, 1/4 x 1-1/4 long PIN, 3/8 Self Locking Cotter or SWIVEL, 3/8 Thru Hole, Special SWIVEL, 3/8-24 Adjustment SPRING, Rectangular Wire Die, Blue WELDMENT, Brake Rod Crossrod WELDMENT, Park Brake Handle WELDMENT, Brake Linkage Pivot WELDMENT, Brake Linkage Bellcrank ASSEMBLY, Brake Ausco p/n CC 83022; used on Series 2 (late production only) BRACKET, Brake Mounting BUSHING, Teflon Impregnated FRONT LINKAGE, Park Brake (3/8-24 thread) 15A REAR LINKAGE, Park Brake (3/8-24 thread) 48 & 52 Deck Models 15B ROD, Brake Rear (3/8-16 thread) 61 Deck Models Only GRIP, Parking Brake WASHER, 3/8 SAE Flat 18A NUT, 3/8-24, Hex Jam, GR 5 or B 18B NUT, 3/8-16, Hex Jam, GR 5 or B NUT, 5/16-18 Hex Nyloc BOLT, 5/16-18 x 3/4 Short Neck Carriage, GR WASHER,.64 I.D. x.99 O.D. x.05 Flat SHOULDER BOLT, 3/8-16 Hex Socket Head NUT, 3/8-16 Hex Center Lock Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 27 Manual No

28 HYDRO PUMP ASSEMBLIES Manual No MID-MOUNT Z-RIDER ZERO TURNING 28 SERIES 3

29 HYDRO PUMP ASSEMBLIES Item Part No Qty Description Note PUMP, Hydro-Gear (Left Hand) BDP-10A-331, W/ RTN in Reverse PUMP, Hydro-Gear Right Hand) BDP-10A-454 W/ RTN in Reverse KIT, Fan Hub (Includes 1 each of 3 items shown below) (Hydro Gear p/n 70632) for BDP- 10A Pump w/thru Shaft HUB, Fan Mount WASHER, Belleville, Fan Mount NUT, Hex Nyloc FAN, 7 Nylon, Counter-Clockwise NUT, 3/8-16 Hex Nyloc WASHER, 3/8 Flat RETAINER, 3/8 Bolt BOLT, 3/8-16 x 1-1/4 Short Neck Carriage GR PULLEY, D Bushing x 15mm Bore SCREW, 1/4-20 x 1 Hex Head Cap GR 5 or KEY, M5 x M WASHER, 1/4 x 1x 1/8 Flat WASHER, 1/4 Split Lock SCREW, M6 1.0 x 12mm Hex Head Cap PULLEY, 4.25 O.D. x OA x H Tapered Bore Double Pump Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 29 Manual No

30 HOSE ASSEMBLY (48" & 52" Deck) Manual No MID-MOUNT Z-RIDER ZERO TURNING 30 SERIES 3

31 HOSE ASSEMBLY (48" & 52" Deck) Item Part No Qty Description Note FILTER HEAD BRACKET, Filter FILTER SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 5A MOTOR, Hydraulic, Left Hand Includes Castle Nut & #502 Woodruff Key, 5/16 x 1 5B MOTOR, Hydraulic, Right Hand Includes Castle Nut & #502 Woodruff Key, 5/16 x BOLT, 1/2-13 x 6 Hex Head Cap GR WASHER, 1/2 Split Lock NUT, 1/2-13 Hex GR B MOUNTING PLATE, Hydro Motor BOLT, 1/2-13 x 1-1/2 Square Neck Carriage, GR NUT, 1/2-13 Hex Nyloc WELDMENT, Rear Crossbrace CONNECTOR, Straight Hydraulic (Parker # 8-10 F5OLO-S) CONNECTOR, 90-Degree Hydraulic (Parker # 8-10 C5OLO-S) HOSE, 13-3/4 Hydraulic (Parker # F436BKJCJC ) COTTER PIN, 1/8 x 1-1/ HOSE, 17-1/2 Hydraulic (Parker # F436BKJCJ ) CONNECTOR, 45-Degree Hydraulic (Parker #8-6 V 50L0-S) HOSE, 18-1/2 (Parker R836BKJCJ ) HOSE, 12-1/4 (Parker # R836BKJ9NR ) HOSE, 6-1/2 (Parker # R836BKJ9NR ) CONNECTOR, 90-Degree Hydraulic (Parker # 8-6 C5OLO-S) CONNECTOR, Straight Hydraulic (Parker # 8-6 F5OLO-S) CONNECTOR, 45-Degree Hydraulic (Parker # V5OLO-S) SCREW, 1/4-20 x 1/2 Hex Head Cap, GR WASHER, 1/4 Split Lock WASHER,.531 I.D. Flat Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 31 Manual No

32 HOSE ASSEMBLY (61" Deck) Manual No MID-MOUNT Z-RIDER ZERO TURNING 32 SERIES 3

33 HOSE ASSEMBLY (61" Deck) Item Part No Qty Description Note FILTER HEAD BRACKET, Filter FILTER SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap 5A MOTOR, Hydraulic, Left Hand Includes Castle Nut & #502 Woodruff Key, 5/16 x 1 5B MOTOR, Hydraulic, Right Hand Includes Castle Nut & #502 Woodruff Key, 5/16 x BOLT, 1/2-13 x 6 Hex Head Cap, GR WASHER, 1/2 Split Lock NUT, 1/2-13 Hex GR B PLATE, Mounting BOLT, 1/2-13 x 1-1/2 Square Neck Carriage, GR NUT, 1/2-13 Hex Nyloc WELDMENT, Rear Crossbrace CONNECTOR, Straight Hydraulic (Parker # 8-10 F5OLO-S) BOLT, 1/2-13 x 3-3/4 Hex Head Cap HOSE, 15-1/2 Hydraulic (Parker # F436JCJ ) HOSE, 17-1/2 Hydraulic (Parker # F436BKJCJ ) WASHER,.531 I.D. Flat CONNECTOR, 90-Degree Hydraulic (Parker # 8-6 C5OLO-S) HOSE, 18-1/2 (Parker # R836BKJCJ ) HOSE, 12-1/4 (Parker # R836BKJ9NR ) HOSE, 6-1/2 (Parker # R836BKJ9NR ) CONNECTOR, 45-Degree Hydraulic (Parker #8-6 V 50L0-S) CONNECTOR, Straight Hydraulic (Parker # 8-6 F5OLO-S) CONNECTOR, 45-Degree Hydraulic (Parker # V5OLO-S) SCREW, 1/4-20 x 1/2 Hex Head Cap, GR WASHER, 1/4 Split Lock PIN, 1/8 x 1-1/2 Cotter or , 1-1/4 long HOSE, 19-1/2 (Parker # F436BKJCJ ) CONNECTOR, 90-Degree Hydraulic (Parker # 8-10 C5OLO-S) Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 33 Manual No

34 HYDRO RESERVOIR ASSEMBLY Manual No MID-MOUNT Z-RIDER ZERO TURNING 34 SERIES 3

35 HYDRO RESERVOIR ASSEMBLY Item Part No Qty Description Note ASSY, Hydraulic Tank (Includes 4 items shown below) TANK, Hydraulic, NZM per , Tank Assembly CAP, Vented (Kelch # H4550D) per , Tank Assembly GROMMET (Dapco # 12078) per , Tank Assembly ELBOW FITTING (Dapco # 12183) per , Tank Assembly BRACKET, R.H. Hydro Tank Mount BRACKET, L.H. Hydro Tank Mount SCREW, 1/4-20 x 1 Hex Head Cap GR WASHER, 1/4 Flat SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap NUT, 1/4-20 Hex Nyloc CABLE TIE, 7 Long (not shown) Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 35 Manual No

36 HYDRO IDLER ASSEMBLY Manual No MID-MOUNT Z-RIDER ZERO TURNING 36 SERIES 3

37 HYDRO IDLER ASSEMBLY Item Part No Qty Description Note NUT, 3/8-16 Hex Center Lock NUT, 3/8-16 Hex Flange Lock SPRING, Extension SCREW, 3/8-16 x 1-1/2 Hex Head Cap, GR WASHER,.468 x 1.85 x HAIR PIN, 3/32 x 1-1/ WASHER, 3/8 Flat SAE SWIVEL, Adjustable SPACER,.340 I.D. x.63 O.D. x.310 Thick NUT, 5/16-18 Hex, GR 5 or B NUT, 5/16-18 Hex Nyloc WELDMENT, Idler Arm PULLEY, 4 O.D. x.391 I.D. x 1.25 Backside Idler BELT, Hydro Drive (HA Section, 47.5 Effective Length) SET, Matched Traction Drive Belts (Kit contains two belts (p/n ) EYEBOLT, 5/16-18 may be used instead of BOSS, Idler Arm Pivot SLEEVE BUSHING, 3/4 I.D BOLT, 3/8-16 x 3-1/2 Hex Head, GR NUT, 3/8-16 Hex, GR 5 or B WASHER, 3/8 Split Lock WASHER, 3/8 Flat SAE Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 37 Manual No

38 ENGINE SUB-ASSEMBLY Manual No MID-MOUNT Z-RIDER ZERO TURNING 38 SERIES 3

39 ENGINE SUB-ASSEMBLY Item Part No Qty Description Note 1 1 ** ENGINE, 19HP Kawasaki (Model FH601V-ES20) 1 1 ** ENGINE, 21HP Kawasaki (Model FH641V-DS17) 1 1 ** ENGINE, 25HP Kawasaki (Model FH721V-DS29) 1 1 **ENGINE, 27HP Kohler (Model PS-CV ) includes oil drain pipe (Kohler ) & pipe cap (Kohler ) SCREW, 5/16-18 x 1-1/2 Hex Head Cap, GR RETAINER, 3/8 Bolt NUT, 5/16-18 Hex Top Lock GR B ASSEMBLY, Oil Valve Kawasaki engines only KEY, 1/4 Square x 3/ PULLEY, 4.26 x OAL x 1 Bore CLUTCH, Electric (Ogura Model # GT2.5-RM01) WASHER, Rectangular Steel BUMPER, Electric Clutch SCREW, 5/16-18 x 1-1/4 Hex Head Cap GR WASHER,.468 x 1.85 x.25 Flat WASHER, 7/16 Split Lock SCREW, 7/16-20 x 2-1/2 Hex Head Cap, GR 5 with locking patch BRACKET, Clutch BOLT, 3/8-16 x 1 Square Neck Carriage GR NUT, 3/8-16 Hex Nyloc KEY, 1/4 Square x 2-1/4 Long RETAINER, 5/16 Bolt SPACER, Clutch WASHER, 5/16 Flat OUTLET, Muffler used on NZM27613KH only SCREW, #8-18 x 1/2 Hex Washer Self-Tap used on NZM27613KH only NUT, M8 x 1.25 Hex (Not Shown) used on NZM27613KH only WASHER, 5/16 Split Lock (Not Shown) used on NZM27613KH only MUFFLER Kawasaki engines only NUT, 5/16-18 Hex Flange Lock Footnotes: Note** Purchase engine components directly from engine manufacturer dealer. MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 39 Manual No

40 SEAT ASSEMBLY Manual No MID-MOUNT Z-RIDER ZERO TURNING 40 SERIES 3

41 SEAT ASSEMBLY Item Part No Qty Description Note ** SEAT ASSY (Seats Inc. p/n ) (Incl. angle brackets, seat pan, cushions, flip-up armrests, adjusters w/lock & seat switch) ** SEAT ASSY (Seats Inc. p/n VD310 Silver/Black (not used on NZM27613KH only shown) SPRING, Compression- Seat Support 2.75" Tall on Kawasaki models SPRING, Compression- Seat Support 2.25" Tall on Kohler models SCREW, 5/16-18 x 3/4 Hex Washer Self-Tap WASHER, 3/8 SAE Flat NUT, 3/8-16 Hex Nyloc SEAT PAN CROSSMEMBER, Seat Support WELDMENT, Hinge Bracket (shown) on Kawasaki models WELDMENT, Hinge Bracket (not shown) on Kohler models SHOULDER BOLT, 5/ NUT, 5/16-18 Large Flange Hex Center Lock BOLT, 3/8-16 x 1 Square Neck Carriage GR GUARD, Fan KNOB, 1/4-20 x 3/4 Thread WELL-NUT, 1/4-20 x 53/ SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap CLIP, Open 3/8 Cushioned LATCH, Seat Support WASHER, 5/16 Flat NUT, 5/16-18 Hex Nyloc SPRING, Extension SCREW, 5/16-18 x 2 Hex Head Cap GR SPACER,.340 I.D. x.63 O.D. x.310 Thick BUSHING, Seat SPACER SPRING, Compression 1.52" Tall on Kawasaki models SPRING, Compression 1.72" Tall on Kohler models HOLDER, Seat Switch SWITCH, Seat, NC DECAL, Danger- High Speed Rotating Parts DECAL, Reservoir Oil Level SPACER, Washer (not shown) used on NZM27613KH only BOLT, 3/8-16 x 3/4 Square Neck Carriage used on NZM27613KH only Footnotes: Note ** Order parts (arm rests, ect.) from Seats, Inc MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 41 Manual No

42 MUFFLER GUARD ASSEMBLY Manual No MID-MOUNT Z-RIDER ZERO TURNING 42 SERIES 3

43 MUFFLER GUARD ASSEMBLY Item Part No Qty Description Note UPPER BRACKET, Muffler Guard MOUNT, Lower Muffler Guard GUARD, Muffler (Back Plate) REAR BRACE, Muffler Guard GUARD, Muffler NUT, 3/8-16 Hex Nyloc BOLT, 3/8-16 x 1 Square Neck Carriage GR BOLT, 3/8-16 x 3/4 Square Neck Carriage NUT, 3/8-16 Hex Center Lock Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 43 Manual No

44 48" CUTTING DECK ASSEMBLY (Sub Assy) Manual No MID-MOUNT Z-RIDER ZERO TURNING 44 SERIES 3

45 48" CUTTING DECK ASSEMBLY (Sub Assy) Item Part No Qty Description Note WELDMENT, 48 Deck Deck Group SCREW, 3/8-16 x 2 Hex Head Cap, GR 5 or WELDMENT, Pivot Pin SCREW, 3/8-16 x 1 Hex Head Cap, GR NUT, 3/8-16 Hex Nyloc ROLLER Low Density Polyethylene or WASHER, 5/8 Flat SAE GAUGE WHEEL, Polyethylene BOLT, 3/8-16 x 1 Square Neck Carriage GR NUT, 1/2-13 Hex, GR B SCREW, 1/2-13 x 2 Hex Head Cap, GR BOLT, 1/2-13 x 3-3/4 Hex Head Cap, GR NUT, 1/2-13 Hex Light Nyloc ASSEMBLY, Pusher Bar (Includes items 15-17) WELDMENT, Pusher Bar SLEEVE - Suspension BUSHING - Suspension ASSEMBLY, Chain & Eyebolt see FRONT FRAME ASS'Y (Deck Lift) page, item BRACKET, Front Deck Lift, Right Hand BRACKET, Front Deck Lift, Left Hand SPACER, Gauge Wheel BOLT, 1/2-13 x 5 Hex Head WASHER,.406 x 1.50 x.120 Flat NUT, 3/8-16 Hex Flange Lock WHEEL BRACKET Front Right WHEEL BRACKET Front Left Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 45 Manual No

46 48" CUTTING DECK ASSEMBLY (Final Assy) Manual No MID-MOUNT Z-RIDER ZERO TURNING 46 SERIES 3

47 48" CUTTING DECK ASSEMBLY (Final Assy) Item Part No Qty Description Note BELT COVER, Left Hand BELT COVER, Right Hand SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap SCREW, 3/8-16 x 1 Hex Head Cap, GR NUT, 3/8-16 Hex Nyloc BELT, Primary (HB Section, effective length) 7 1 ASSEMBLY, Idler (see breakdown on IDLER ASSEMBLIES page) 8 1 ASSEMBLY, Center Spindle (see breakdown on DECK SPINDLE ASSEMBLIES page) 9 2 ASSEMBLY, Spindle (see breakdown on DECK SPINDLE ASSEMBLIES page) SPRING, Chute PIN, Chute Hinge 12 1 ASSEMBLY, Discharge Chute includes 5 items below DEFLECTOR, Bottom BOLT, 3/8-16 x 1-1/4 Square Neck Carriage, GR CHUTE, Rubber 48 replaces WELDMENT, 48 Chute NUT, 3/8-16 Hex Nyloc PIN, 3/32 x 1 Cotter V-BELT, Secondary, 48 (HB Sect effective length SPRING, Idler (1.17 O.D. x 7.5 long) SPRING, Idler Primary (1.25 O.D. x 10 long) Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 47 Manual No

48 52" CUTTING DECK ASSEMBLY (Sub Assy) Manual No MID-MOUNT Z-RIDER ZERO TURNING 48 SERIES 3

49 52" CUTTING DECK ASSEMBLY (Sub Assy) Item Part No Qty Description Note WELDMENT, 52 Deck SCREW, 3/8-16 x 2 Hex Head Cap, GR WELDMENT Pivot Pin SCREW, 3/8-16 x 1 Hex Head Cap, GR NUT, 3/8-16 Hex Nyloc ROLLER Low Density Polyethylene or WASHER, 5/8 Flat SAE GAUGE WHEEL, Polyethylene BOLT, 3/8-16 x 1 Square Neck Carriage, GR NUT, 1/2-13 Hex Flange GR SCREW, 1/2-13 x 2 Hex Head Cap, GR BOLT, 1/2-13 x 3-3/4 Hex Head Cap, GR NUT, 1/2-13 Hex Light Nyloc ASSEMBLY, Pusher Bar (Includes items 15-17)(Not Shown) WELDMENT, Pusher Bar SLEEVE - Suspension BUSHING - Suspension ASSEMBLY, Chain & Eyebolt (see Front Frame Assy page) see FRONT FRAME ASS'Y (Deck Lift) page, item BRACKET, Front Deck Hanger R. H BRACKET, Front Deck Hanger L. H BOLT, 1/2-13 x 5 Hex Head SPACER, Gauge Wheel WASHER,.406 x 1.50 x.120 Flat NUT, 3/8-16 Hex Flange Lock WHEEL BRACKET Front Right WHEEL BRACKET Front Left Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 49 Manual No

50 52" CUTTING DECK ASSEMBLY (Final Assy) Manual No MID-MOUNT Z-RIDER ZERO TURNING 50 SERIES 3

51 52" CUTTING DECK ASSEMBLY (Final Assy) Item Part No Qty Description Note SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap BELT COVER, Left Hand BELT COVER, Right Hand SCREW, 3/8-16 x 1 Hex Head Cap, GR ASSEMBLY, Idler (see breakdown on Idler Assy page) *V-BELT, Secondary- 52 (HB Section, effective length) *BELT, Primary (HB Section, effective length) SPRING, Idler (1.17 O.D. x 7.5 long) SPRING, Idler Primary (1.25 O.D. x 10 long) SPRING, Chute PIN, 3/32 x 1 Cotter PIN, Chute Hinge NUT, 3/8-16 Hex Nyloc 14 2 ASSEMBLY, Spindle (see breakdown on Deck Spindle Assy page) ASSEMBLY, Center Spindle (see breakdown on Deck Spindle Assy page) 16 1 ASSY, Discharge Chute, 52 Deck incl. items 13, 17, 18, 19 & DEFLECTOR BOTTOM (52 Deck) BOLT, 3/8-16 x 1-1/4 Square Neck Carriage, GR DEFLECTOR, 52 Chute (Rubber) WELDMENT, 52 Discharge Chute Footnotes: *NOTE: Snapper part number stamped on belt MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 51 Manual No

52 61" CUTTING DECK ASSEMBLY (Sub Assy) Manual No MID-MOUNT Z-RIDER ZERO TURNING 52 SERIES 3

53 61" CUTTING DECK ASSEMBLY (Sub Assy) Item Part No Qty Description Note WELDMENT, 61 Deck SCREW, 3/8-16 x 2 Hex Head Cap, GR WELDMENT Pivot Pin SCREW, 3/8-16 x 1 Hex Head Cap, GR NUT, 3/8-16 Hex Nyloc ROLLER, Low Density Polyethylene or WASHER, 5/8 Flat SAE GAUGE WHEEL, Polyethylene BOLT, 3/8-16 x 1 Square Neck Carriage, GR NUT, 1/2-13 Hex Light Nyloc SCREW, 1/2-13 x 2 Hex Head Cap, GR BOLT, 1/2-13 x 3-3/4 Hex Head Cap, GR ASSEMBLY, Rear Linkage (ref. Front Frame Assembly Deck Lift page item #7B) WELDMENT, Pusher Bar SLEEVE - Suspension BUSHING - Suspension BRACKET, Deck Lift, Right Hand BRACKET, Deck Lift, Left Hand BOLT, 1/2-13 x 5 Hex Head WASHER,.406 x 1.50 x.120 Flat NUT, 3/8-16 Hex Flange Lock WHEEL BRACKET, Front Right WHEEL BRACKET, Front Left SPACER, Gauge Wheel BRACKET, Deck Lift, RH Rear BRACKET, Deck Lift, LH Rear Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 53 Manual No

54 61" CUTTING DECK ASSEMBLY (Final Assy) Manual No MID-MOUNT Z-RIDER ZERO TURNING 54 SERIES 3

55 61" CUTTING DECK ASSEMBLY (Final Assy) Item Part No Qty Description Note SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap BELT COVER, 61 Deck 3 1 ASSEMBLY, Idler (see breakdown on Idler Assy page) SCREW, 3/8-16 x 1 Hex Head Cap, GR *BELT, Primary (HB Section, 94.2 effective length) *V-BELT, Secondary- 61 (HB Section, effective length) SPRING, Idler (1.17 O.D. x 7.5 long) SPRING, Idler Primary (1.25 O.D. x 10 long) SPRING, Chute PIN, 3/32 x 1 Cotter PIN, Chute Hinge NUT, 3/8-16 Hex Nyloc 13 2 ASSEMBLY, Spindle (see breakdown on Deck Spindle Assy page) 14 1 ASSEMBLY, Center Spindle (see breakdown on Deck Spindle Assy page) 15 1 ASSEMBLY, Discharge Chute, 61 Deck incl. items 12, 16, 17, 18 & DEFLECTOR BOTTOM (61 Deck) BOLT, 3/8-16 x 1-1/4 Square Neck Carriage, GR CHUTE, Rubber (61 Deck) WELDMENT, 61 Discharge Chute Footnotes: *NOTE: Snapper part number stamped on belt MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 55 Manual No

56 IDLER ASSEMBLIES Manual No MID-MOUNT Z-RIDER ZERO TURNING 56 SERIES 3

57 IDLER ASSEMBLIES Item Part No Qty Description Note WELDMENT, Idler Plate 2 1 ASSEMBLY, Primary Idler Includes items 6 (2), 7, 8 (3), 9, 10, 11, 12, 13 & ASSEMBLY, Secondary Idler Includes items 6 (2), 7, 8, 9, 15, 16 & BUSHING, 1 Machine RING, 1 External Retaining BUSHING, Idler (Powdered Metal) LUBE FITTING, 3/ WASHER, 3/8 Flat NUT, 3/8-16 Hex Center Lock, GR 5 or B SCREW, 3/8-16 x 3-1/4 Hex Head Cap, GR WELDMENT, Primary Idler Arm BUSHING - Idler RETAINER, Idler Belt PULLEY, Flat Idler SCREW, 3/8-16 x 1-3/4 Hex Head Cap, GR WELDMENT, Secondary Idler Arm PULLEY, Idler Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 57 Manual No

58 DECK SPINDLE ASSEMBLIES Manual No MID-MOUNT Z-RIDER ZERO TURNING 58 SERIES 3

59 DECK SPINDLE ASSEMBLIES Item Part No Qty Description Note SUB-ASSEMBLY, Spindle (Incl. the 8 items below) SPACER, Bearing *RING, Spindle Retaining VENT, Spindle (Alemite # ) BALL BEARING (2 per item 1, sub-assembly) ASSEMBLY, Spindle Housing (includes items 4 & 8) , Casting Ass'y includes spindle housing & 6 item 7's BOLT, Ribbed (3/8-16 x 1-1/4 Thread) (6 per item 1, subassembly) FITTING, Lube (1/4-28 Special Thread Forming) Alemite #3038-B SHAFT, Spindle SPACER, Blade PULLEY, 5.75 Diameter NUT, 3/8-16 Hex Nyloc (6 per spindle assembly) WASHER, Beveled PULLEY, Driven (48 Deck only) PULLEY, Driven (52 Deck only) PULLEY, Driven (61 Deck only) BLADE, 16-1/2 (48 Deck only) BLADE, 18 Commercial w/extra Cut (52 Deck only) BLADE, 21 (61 Deck only) BOLT, 5/8-11 x 7-1/2 Hex, GR NUT, 5/8-11 Hex Flange Lock, GR WASHER, Spindle *SEAL, Nylos *WASHER Footnotes: *NOTE: For Bearing Pre-Seal Kit (63240) installation, discard 3 & replace with 19 & 20. MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 59 Manual No

60 DECALS Manual No MID-MOUNT Z-RIDER ZERO TURNING 60 SERIES 3

61 DECALS Item Part No Qty Description Note DECAL, Snapper Pro DECAL, Ear Protection DECAL, Park Brake DECAL, Oil Reservoir Overfill Warning DECAL, Caution (Spring Mechanism) DECAL, Danger (High Speed Rotating Parts) DECAL, Detent DECAL, Tank Selector DECAL, Caution ROPS DECAL, Caution ROPS (Spanish) DECAL, Warning (SP) DECAL, Warning, Rollbar DECAL, ROPS Overhang DECAL, Control Panel DECAL, Motion Control Levers DECAL, Warning ROPS DECAL, Warning ROPS (Spanish) DECAL, Fuse Block DECAL, Danger, Guard/Catcher DECAL, 48 Deck, (silver) DECAL, 52 Deck (silver) DECAL, 61 Deck (silver) Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 61 Manual No

62 CONTROL PANEL ASSEMBLY Manual No MID-MOUNT Z-RIDER ZERO TURNING 62 SERIES 3

63 CONTROL PANEL ASSEMBLY Item Part No Qty Description Note CONTROL PANEL CONTROL LEVER, Throttle/Choke CONTROL CABLE, Throttle STRAP, Tether CONTROL CABLE, Choke SCREW, 5/16-18 x 5/8 Hex Washer Self-Tap SCREW, #10-32 x 5/8 Hex Washer Self-Tap Note: These items are also shown on the Electrical Components page NUT, #10-32 Nyloc Note: These items are also shown on the Electrical Components page SWITCH, PTO, Yellow Note: These items are also shown on the Electrical Components page SWITCH, Ignition Note: These items are also shown on the Electrical Components page HOUR METER w/flash Alerts Note: These items are also shown on the Electrical Components page CHOKE PLATE, Kohler Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 63 Manual No

64 ROLL BAR PROTECTIVE STRUCTURE Manual No MID-MOUNT Z-RIDER ZERO TURNING 64 SERIES 3

65 ROLL BAR PROTECTIVE STRUCTURE Item Part No Qty Description Note TOP LOOP, Folding WELDMENT POST, RH WELDMENT POST, LH PIN, Hinge (ROPS) STAR KNOB (5/16-18 thread) SCREW, 1/2-13 x 3-1/4 Hex Head Cap, GR NUT, 1/2-13 Hex Center Lock, GR 5 or BOLT, 3/8-16 x 1 Square Neck Carriage, GR SEAT BELT, w/metal Strap NUT, 3/8-16 Hex Center Lock WELDMENT, Right Hand Socket see also on REAR FRAME & TANK BRACKETS page WELDMENT, Left Hand Socket see also on REAR FRAME & TANK BRACKETS page SEAT BELT, Retracter BRACKET, Seat Beal, LH see also on FUEL TANK ASSEMBLY page SCREW, 1/2-13 x 1 Hex Head Cap, GR 5 Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 65 Manual No

66 ELECTRICAL COMPONENTS Manual No MID-MOUNT Z-RIDER ZERO TURNING 66 SERIES 3

67 ELECTRICAL COMPONENTS Item Part No Qty Description Note SWITCH, PTO, Yellow also shown on CONTROL PANEL ASSEMBLY page HOUR METER w/flash Alerts Sendec Corp. Model No (also shown on CONTROL PANEL page) SWITCH, Seat, NC also shown on SEAT ASSEMBLY page BRACKET, Battery Hold-Down SWITCH, Ignition KEY SET (not shown) qty. 2 keys per set CLIP, Harness SCREW, #10-32 x 5/8 Hex Washer Self-Tap NUT, #10-32 Hex Nyloc NUT, 1/4-20 Hex Nyloc WASHER, 1/4 Flat NUT, 1/4-20 Hex Center Lock SCREW, 1/4-20 x 5/8 Hex Head Self-Tap or (w/loose washer) CLIP, Open 3/8 Cushioned shown on Rear Frame & Tank Bracket page & Seat Assembly page CABLE TIE, 7 Long (not shown) SOLENOID, Super Trombetta vendor p/n (used on Kawasaki only) SCREW, 1/4-20 x 1/2 Hex Washer Self-Tap or SCREW, 1/4-20 x 5/8 Hex Head Cap GR BATTERY, 11 Plate 375CCA- Wet SWITCH, DP NO/NC Snap-In Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 67 Manual No

68 WIRING HARNESS (Kawasaki Engines) Manual No MID-MOUNT Z-RIDER ZERO TURNING 68 SERIES 3

69 WIRING HARNESS (Kawasaki Engines) Item Part No Qty Description Note HARNESS, Wiring CABLE, Battery- Positive (Red 6 Gage, 34 long) not shown CABLE, Battery- Ground (Black 6 Gage/14 Gage, 23 long) not shown CABLE, Solenoid to Starter (Red 6 Gage, 10 long) not shown WIRE, Solenoid- Ground (Black 10 Gage, 6-1/2 long) not shown Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 69 Manual No

70 WIRING HARNESS (Kohler Engines) Manual No MID-MOUNT Z-RIDER ZERO TURNING 70 SERIES 3

71 WIRING HARNESS (Kohler Engines) Item Part No Qty Description Note WIRE HARNESS, Kohler/Twin CABLE, Battery- Positive (Red 6 Gage, 34 long) not shown CABLE, Battery- Ground (Black 6 Gage/14 Gage, 23 long) not shown Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 71 Manual No

72 WIRING SCHEMATIC (Kawasaki Engines) Manual No MID-MOUNT Z-RIDER ZERO TURNING 72 SERIES 3

73 WIRING SCHEMATIC (Kawasaki Engines) Item Part No Qty Description Note HARNESS, Wiring Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 73 Manual No

74 WIRING SCHEMATIC (Kohler Engines) Manual No MID-MOUNT Z-RIDER ZERO TURNING 74 SERIES 3

75 WIRING SCHEMATIC (Kohler Engines) Item Part No Qty Description Note HARNESS, Wiring, Kohler/Twin Footnotes: MID-MOUNT Z-RIDER ZERO TURNING SERIES 3 75 Manual No

76

77

78 Parts Manual for MID-MOUNT Z-RIDER ZERO TURNING HYDRO DRIVE NZM SERIES 3 IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY. McDonough, GA, U.S.A. COPYRIGHT 2006 SNAPPER PRODUCTS, INC. ALL RIGHTS RESERVED. Revision IR, 7/21/2006 Manual No