Quick Selection Catalogue Version 6.1

Transcription

1 Quick Selection Catalogue Version 6.1 1

2 WHAT DO YOU USE THE QUICK SELECTION CATALOGUE TO? The quick selection catalogue is designed to provide opportunity to quick and easy find the appropriate products for a given case. Once you have found an actual product and dimension, you may find additional details for engineering in the product's own data sheet. All the data sheets is available at There are also separate dimensioning programs for chilled beams and sound attenuators. WHAT DOES THE TABLES IN THE QUICK SELEC- TION CATALOGUE SAY? Quick selection tables indicate maximum airflow that the productscan handle under normal conditions and requirements.for each dimension is given the airflowsinvolving specified sound power levels. where the productshave an damper installed the airflows is given at 30 or50 Pa total pressure loss over the device. When it comes to valves, it is important to note thatthe sound pressure level in the room normally is lower than indicatedsound power level. Previously, it was customary to state sound pressure levelsat the valve placed in a room with 4 db attenuationin all frequencies. db(a)- value in such a room is 4 dblower than the sound power level. To estimate resultantsound pressure level in various room types and with different numbers, the program "Aurakustikk" can be used. 2

3 Contents Main group Product Page Exhaust valves USI 4 Inter 5 LØV-A 6-7 KSO 8 LVS 9 ESNU 10 UPK Orion-ATV RIA-SA 19 Grilles and transfer units RIA 20 OVA 21 LOV 22 VSR 23 TOG-R 24 Supply air diffusers and plenum boxes Pegasus Comfort Opus-4/5 28 Pegasus Orion LØV with Sirius Comfort Orion Opus with Sirius Comfort Orion PTV with Sirius Comfort TLH 38 LØV-R TLG/LØV Tellus-LØV 43 Tellus-Opus 44 Tellus-LØV VAV Tellus-Opus VAV TLK TUB 51 TIH and TIR DKW 54 RFD Orion-LØV Orion-Opus Orion-PTV JBV Orion-LØV-Sirius Orion-Opus-Sirius Orion-PTV-Sirius Siv-inn comfort and industry Siv-inn 1 71 Siv-inn Siv-inn Inlaid 73 Siv-inn school 74 Siv-inn Siv-inn T/V 77 Siv-inn PP and PK 78 Siv-inn Aula Dampers and VAV DRS/DRS-T EPS 83 Rego-T 84 Iris 85 Leo TSK 89 Sound attenuators LEV 90 LKR 91 LKK 92 LKL 93 Access doors and duct systems ILP and ILS 94 KSA 95 Chilled beams Svalbard-H Svalbard-I Svalbard-F DID Automation VIP-X 105 EasyLink 106 3

4 USI The USI extract air terminal is intended for open installation. It is suitable for high air flow rates, and can thus be used as a central extraction unit in large rooms ideal in combination with VAV. The valve is available with and without integrated sound attenuator. DIMENSIONS AND WEIGHT, USI Dim. D A Weight[kg]¹ Weight[kg]² ,0 11, ,4 13, ,4 15, ,8 19, ,5 25,5 Table 2: 1 without sound attenuator, 2 with sound attenuator The device is made of galvanised steel, and comes in RAL gloss 30. Other colours are available on request. QUICK SELECTION USI [m³/h] Dim 25dB(A) 30dB(A) 35dB(A) Table 1: The table shows air flow rates at given sound power levels. ORDER CODE, USI USI / L / 0-0 Fig. 1 Dimension: Ø200 - Ø500 L = Design with sound attenuation SL = Special finish SM = Special material USI-315 / L / 0-0 USI dim. Ø315, with sound attenuation 4

5 Inter Inter is used to simplify the installation of valves in lightweight ceilings (mineral wool). Inter is produced in galvanised steel. INSTALLATION Cut a groove in the ceiling plate (1) D1 + 5 mm, using the end-piece of the Inter as a template. Install the Inter (2) in the ceiling plate (1) by using 3 self-drilling screws inside the Inter to attach the mounting frame for the valve (3). Then fit the valve in the mounting frame. Finally, install the assembled ceiling plate in a modular ceiling system. Use of connection nipple (4) or bend between Inter and Spiro duct (5) is recommended. ORDER CODE, Inter Inter Product Dimension Ø100 - Ø200 Inter-160 Inter dimension Ø160. DIMENSIONS AND WEIGHT, INTER Dim. D1 H1 H2 Weight [kg] , , , ,60 Table 1. Fig. 2 MAINTENANCE No specific maintenance requirements ENVIRONMENT Enquiries regarding product declaration can be directed to our sales team, or information can be found at our website: Fig. 1 5

6 LØV-A LØV-A is a circular exhaust valve for ceiling mounting. It is suitable for installation in fixed ceilings. LØV-A features a removable front panel with perforation. Both the valve front and the ceiling plate are in a steel design. The valve body is in aluminium and is fitted with an EPDM rubber gasket at the connection collar. All internal and external valve elements are in a RAL gloss 30 finish. Other colours are available on request. LØV-A QUICK SELECTION [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) 40 db(a) Table 1: The table shows air flow rates at given sound power levels. ORDER CODE, LØV-A (LOEV-A) DIMENSIONS AND WEIGHT, LØV-A Cut-out dimensions: ØG+5 Dim. A B C G E F I Weight valve [kg] , , , , ,7 Table 2 G C B A = Standard exhaust pattern LØV-A SL = Special finish F E 11 A LOEV-A Explantation: LOEV-A, dimension Ø160 Dimension: Ø100 Ø315 Fig. 1 ORDER CODE, Luna Luna UI = Outlet installed, low profile design I = Insulated Dimension outlet: Ø100 Ø315 (Diffuser connection) Dimension inlet: Ø100 Ø315 (Duct connection) Luna Explantation: Luna plenum box with duct connection dim. Ø125 and diffuser connection dim. Ø160 6

7 LØV-A with Luna plenum box The Luna plenum box is recommended for improved sound attenuation, and works as an adjustment and measurement unit. Luna is a rectangular box with a removable damper providing access to the connecting duct. The damper can be secured in any position required. Luna plenum box features a damper and measuring outlet for commissioning. The box is lined with sound absorber in polyester, and is available in the same dimension or one scale up between inlet and outlet (see table 4). Can be supplied with external condensation insulation. A low-profile version [UI] is also available, and for this design a reduction in capacity of approx. 20% will apply. The distance between valve and box can be increased by up to 35 cm without extending the wire and measuring tube. Luna is supplied in a galvanised finish, and with all four internal walls lined with sound absorber in polyester. The connection collar is fitted with EPDM rubber gasket. DIMENSIONS AND WEIGHT, Luna Dim. D DA B H H1 H2 L L1 L2 Weight Luna [kg] , , , , , , , , , Table 4 QUICK SELECTION LØV-A Luna [m³/h] Dim. Dim. 25 db(a) 30 db(a) 35 db(a) 40 db(a) Table 3: The table shows air flow rates at given sound power levels and 50 Pa total pressure loss. Fig. 2 ORDER CODE, LØV-A (LOEV-A) with Luna LØV-A-L-0 A = Standard exhaust pattern SL = Special finish L = Luna UI = Outlet installed, low profile design I = Insulated L Dimension outlet: Ø100 Ø315 (Diffuser connection) Dimension inlet: Ø100 Ø315 (Duct connection) LOEV-A-L Explantation: LOEV-A exhaust diffuser and Luna plenum box duct connection dim. Ø125 and outlet/diffuser connection dim. Ø160. 7

8 KSO KSO is an extract air terminal device for ceiling or wall mounting. KSO features an adjustable centre cone for air flow rate commissioning. Supplied with mounting frame, KKT, for circular duct.. DIMENSIONS AND WEIGHT, KSO Dim. D A weight [kg] , , , ,7 Table 2 KSO is made of steel, and comes in a RAL gloss 30 finish. Other colours are available on request. KKT is fitted with a rubber gasket on the connection collar. Cone position QUICK SELECTION KSO Cone position - s [m³/h] Dim. [mm] 30 db(a) 35 db(a) 40 (db) Table 1: The table shows air flow rates at given sound power levels. Product ORDER CODE, KSO KSO Dimension Ø100 Ø200 KKT KSO-160 / KKT KSO, dimension Ø160, with KKT mounting frame / KKT = Mounting frame Fig. 1 DIMENSIONS AND WEIGHT, KKT Dim. d D 2 Weight [kg] , , , ,24 Table 3 Fig. 2 8

9 LVS LVS is an extract air terminal device for ceiling or wall mounting. LVS features an adjustable centre cone for air flow rate commissioning. Supplied with mounting frame, KKT, for circular duct.. DIMENSIONS AND WEIGHT, LVS Dim. B C D Weight [kg] , , , ,6 Table 2 LVS is made of steel, and comes in a RAL gloss 30 finish. Other colours are available on request. KKT is fitted with a rubber gasket on the connection collar. QUICK SELECTION LVS Cone position - s [m³/h] Dim. [mm] 30 db(a) 35 db(a) 40 db(a) Table 1. The table shows air flow rates at given sound power levels. Fig. 2 Product ORDER CODE, LVS LVS Dimension Ø100 Ø200 KKT LVS-125 / KKT LVS, dimension Ø125, with KKT mounting frame. / KKT = Mounting frame DIMENSIONS AND WEIGHT, KKT Dim. d D 2 Weight [kg] , , , ,24 Table 3 Fig. 1 Fig. 3 9

10 ESNU ESNU is a circular mesh grille, and can be used as both a supply and extract air unit. ESNU is available in two different designs - with or without decorative flange. ESNU is made of galvanised steel, and units with decorative flange come in a RAL gloss 30 finish as standard. Both designs are fitted with rubber gasket. ESNU without flange is available in dim. Ø100 to Ø1000. ESNU with flange is available in dim. Ø100 to Ø630. ORDER CODE, ESNU DIMENSIONS AND WEIGHT, ESNU ESNU Decorative Weight [kg] flange A- Without With Dim. D1 D2 D3 weighting flange flange ,05 0, ,08 0, ,20 0, ,25 0, ,30 0, ,45 0, ,70 1, ,90 1, ,40 2, , ,00 - Table 1 ESNU / P / 0 Product Dimension: Ø100 - Ø1000 UL = Flange, galvanised steel finish SL = Flange, special finish. P = ESNU with flange (Dim. Ø100 to Ø630 only) ESNU-160 / P / 0 ESNU, dim. Ø160, with decorative flange, white RAL gloss 30 finish Fig. 1 INSTALLATION Can be installed directly in Spiro duct. MAINTENANCE Can be cleaned with a damp cloth or vacuum cleaner as required. ENVIRONMENT Enquiries regarding product declaration can be directed to our sales team, or information can be found at our website: om.no 10

11 UPK (BxH) APPLIcATION UPK is an air-extract grille for wall mounting. It is available in bespoke dimensions and can thus be adapted to fit various groove dimensions or pre-installed boxes. The UPK features square perforation. It is available with pre-drilled holes and enamelled screws. Grilles exceeding 2 m² are split.e. INSTALLATION Installation principle is shown in fig. 2. MATERIALS AND SURFAcE coating The grill is made in steel, and comes in a RAL 9010 finish. It is fitted with polyurethane moulding. Other materials and colours are available on request. QUIcK SELEcTION In terms of projected WxH for the UPK, duct velocity should not exceed 3 m/s. This is to avoid any noise issues. ORDER code, UPK Product B = Width from and incl. 100, max (1000) H = Height from and incl. 100, max (2000) (Max. area in total: 2 m² per grille UPK / 0 SL = Special finish Fig. 2: Installation commissioning A separate measurement and adjustment unit for commissioning is recommended. UPK / 0 UPK, width: 800 and height: 900 MAINTENANcE The valve can be cleaned by using a damp cloth. DIMENSIONS AND WEIGHT, UPK ENVIRONMENT Enquiries regarding product declaration can be directed to our sales team, or information can be found at our website: Fig. 1 11

12 UPK grille UPK-R is a rectangular extract-air grille for integrated wall or ceiling installation. UPK-H is suitable for T-profile ceiling systems, 600 x 600. The UPK-R grille features square perforation and a fitted frame for ATK box mounting. UPK-R panel and frame are made of steel, and are delivered in a RAL gloss 30 finish. Panel in other materials and/or colours are available on request. QUICK SELECTION UPK-R [m³/h] B x H 30dB(A) 35dB(A) 40dB(A) Table 1: The table provides air flow rates at given sound power levels. DIMENSIONS AND WEIGHT, UPK-R UPK-R W x H Weight [kg] 200x100 0,50 300x100 0,55 400x100 0,60 500x100 0,65 300x150 0,70 400x150 0,75 500x150 0,95 400x200 1,00 500x200 1,15 600x200 1,20 500x300 1,50 600x300 1,65 Table 2 Fig. 2, UPK-H B + 35 B H + 35 H ORDER CODE, UPK-R UPK-R / 0-0 Fig 3, UPK-R ORDER CODE, UPK-H UPK-H / 0-0 Product B = Width H = Height SL = Special finish SM = Special material Product SL = Special finish SM = Special material UPK-R / 0-0 UPK-R extract-air grille. 400 width and 200 hight UPK-H / 0-0 UPK-H extract-air grille for T-profile ceiling system, 600x ORDER CODE, ATK Product Connection outlet: B = Rear-entry spigot S = Rear-entry spigot LS = Long-side spigot entry: ATK - S / 0 SM = Special dimensions Grille attachment dimensions: H = Height B = Width Dimension outlet: Ø125 Ø315 ATK-S /0 ATK extraction box with side-entry spigot and Ø250 outlet, 500 width and 150 height for grille attachment. 3 ORDER CODE, ATK-H Product Anslutning utløp: B = Bakanslutning S = Sideanslutning ATK-H - S Dimensjon utløp: Ø Ø400 Eksempel: ATK-H-S-160 Forklaring: ATK-H avtrekkskammer for profilhimling 600x600 med sideanslutning Ø160.

13 UPK grille with ATK box The ATK plenum box is used for improved sound attenuation and commissioning options. This rectangular box is fitted with a removable damper which provides access to the connecting duct. The ATK box features a damper for commissioning. ATK-B, S and LS are equipped with measuring point. The box is insulated with sound absorber in polyester. The ATK box is made in galvanised steel, and is lined with sound absorber in polyester inside. Its connection collar is fitted with an EPDM rubber gasket. ORDER CODE, UPK-R with ATK box UPK-R K / 0-0 B = Width grille H = Height grille K - S Produkt: K = ATK box Connection collar: B = Rear-entry spigot S = Side-entry spigot LS = Long-side spigot entry SL = Special finish SM = Special material Dimension outlet: Ø125 - Ø315 UPK-R K-S-250/0-0 UPK-R extrac-air grille with frame, 500 widt and 150 height, equipped with ATK box with side-entry spigot dim. Ø250, UPK grille in standard white RAL gloss 30 Product ORDER CODE, UPK-H with ATK box K = ATK-H box Connection collar: B = Rear-entry spigot S = Side-entry spigot UPK-H - K / 0-0 K - S QUICK SELECTION, UPK-H SL = Special finish SM = Special material Dimension outlet: Ø160 - Ø400 UPK-H-K-S-315/0-0 UPK-H extrac-air grille for profile ceiling 600x600, equipped with ATK box with side-entry spigot dim. Ø315, UPK grille in standard white RAL gloss 30 finish ATK-H box UPK-H m³/h Dim. Spigot ent. Dim. 25 db(a) 30 db(a) 35 db(a) 160 B 600 x S 600 x B 600 x S 600 x B 600 x S 600 x B 600 x S 600 x * B 600 x * S 600 x Table 3: The table provides air flow rates at given sound power levels and 50 Pa total pressure loss. * = Ø400 is without damper. 4 QUICK SELECTION ATK box UPK-R m³/h Dim. Spigot entl. B x H 25 db(a) 30 db(a) 35 db(a) 125 B 200x S 200x LS 200x B 300x S 300x LS 300x B 400x S 400x LS 400x B 500x S 500x LS 500x B 300x S 300x LS 300x B 400x S 400x LS 400x B 500x S 500x LS 500x B 400x S 400x LS 400x B 500x S 500x LS 500x B 600x S 600x LS 600x B 500x S 500x LS 500x B 600x S 600x LS 600x Table 4: The table provides air flow rates at given sound power levels and 50 Pa total pressure loss. 13

14 UPK grille with ATK box DIMENSIONS AND WEIGHT - ATK, S AND LS ATK Dim. BFxHF D A Weight[kg] x , x , x , x , x , x x , x , x , x x , x ,7 Table 5 Fig. 5, ATK-S Fig. 4, ATK-B Fig. 6, ATK-LS 14

15 UPK-H with ATK box DIMENSIONS AND WEIGHT ATK-H-S/B ATK-H-S/B Dim. D H Weight[kg] , , , , ,2 Table 6 Fig. 7, ATK-H-S Fig. 8, ATK-H-B 15

16 Orion-ATV-T Orion-ATV is a square extract air terminal device for installation in modular ceiling systems. Orion-ATV features a removable front panel with square perforation as standard. Circular pattern can be provided on request. The unit is supplied with top-entry spigot as standard, but is also available with side-entry spigot. Furthermore, the unit is equipped with a TA flange suitable for T-profile ceiling systems, but is also available with alternative flange designs, type: DC, DG, DS and EK (see fig. 3 and under order code). DIMENSIONS AND WEIGHT, Orion-ATV Orion-ATV D Weight valve Dim. [kg] , , , , , ,9 Table 2 The front panel, ceiling plate and valve body are in a steel design, and the connection collar is fitted with an EPDM rubber gasket. Corner connection points are in plastic, and are fitted with holding magnets. All internal and external valve elements are in a RAL gloss 30 finish. Other colours are available on request. QUICK SELECTION [m³/h] Orion-ATV 25 db(a) 30 db(a) 35 db(a) Dim Table 1: The table shows air flow rates at given sound power levels. Fig.1. Orion-ATV with top-entry (T) ORDER CODE, Orion-ATV Orion-ATV - K - TA - T / 0 SL = Special finish Front-panel pattern: K = Square, standard S = Circular, custom For ceiling types: Dimension: Ø160 - Ø400 TA = A-flange DC = Dampa Clip-In DG = Dg-flange Spigot: : DS = Ds-flange T = Top, standard EK24 = E-flange-T24 EK15 = E-flange-T15 Orion-ATV-K-TA-T-160/0 Orion-ATV extract air terminal device with square front pattern, TA flange for inst. in T-profile ceiling. Standard top-entry spigot, dim. Ø160. ORDER CODE, Luna Luna Fig.2. Orion-ATV with side-entry (S) UI = Outlet installed, low profile I = Insulated Dim. outlet: Ø125 - Ø400 Dim. inlet: Ø125 - Ø315 A-flange Dampa Clip-In Dg-flange DS-flange E-flange 16 Luna Luna with inlet Ø125 and outlet Ø160. Fig. 3: Ceiling types T24,T15

17 Orion-ATV with Luna plenum box The Luna plenum box is recommended for improved sound attenuation, and works as an adjustment and measurement unit. Luna is a rectangular box fitted with a removable damper which provides access to the connecting duct. The damper can be secured in any position required. Luna plenum box features a damper and measuring outlet for commissioning. It is insulated with sound absorber in polyester and is available with one or two dimensional changes between inlet and outlet. Furthermore, the box can be delivered with external condensation insulation. A lowprofile design [UI] is also available, and for this type a reduction in capacity of approx. 20% will apply. The distance between valve and box can be increased by up to 35 cm without extending the wire and measuring tube. Luna is supplied in a galvanised finish, and with all four internal walls lined with sound absorber in polyester. The connection collar is fitted with an EPDM rubber gasket. DIMENSIONS S AND WEIGHT, Luna Dim. D DA B H H1 L L1 L2 Weight Luna [kg] , , , , , , , , , ,7 Table 4 QUICK SELECTION Orion-ATV Luna [m³/h] Dim. Dim. 25 db(a) 30 db(a) 35 db(a) Table 3: The table provides air flow rates at given sound power levels and 30 Pa total pressure loss.. Fig. 4 ORDER CODE, Orion-ATV with Luna Orion-ATV - K - TA - T - L / 0 SL = Special finish, valve. Front-panel pattern: K = Square, standard S = Circular, custom For ceiling system: TA = A-flange DC = Dampa Clip-In DG = Dg-flange DS = Ds-flange EK24 = E-flange-T24 EK15 = E-flange-T15 Spigot: T = Topp, standard L S = Side, spesial Produkt: L = Luna UI = Outlet insatalled, low profile I = Insulated Dim. outlet: Ø125 - Ø400 Dim. inlet: Ø125 - Ø315 Orion-ATV-K-TA-T-L /0 Orion-ATV extract air terminal device with square front pattern, TA flange for T-profile ceiling. Top-entry spigot as standard. Luna plenum box with inlet dim. Ø125 and outlet/valve dim. Ø160 Valve in standard RAL gloss 30 finish. 17

18 Orion-ATV-S Orion-ATV-S is a square extract air terminal device for installation in modular ceiling systems. Orion-ATV features a removable front panel with square perforation as standard. Circular pattern can be provided on request. The unit is supplied with side-entry spigot. Furthermore, the unit is equipped with a TA flange suitable for T-profile ceiling systems, but is also available with alternative flange designs, type: DC, DG, DS and E K (see fig. 6 or 7 and under order code). DIMENSIONS AND WEIGHT Orion-ATV-S Orion-ATV-S Weight valve [kg] Dim. D , , , , ,0 Table 6 The front panel, ceiling plate and valve body are in a steel design, and the connection collar is fitted with an EPDM rubber gasket. Corner connection points are in plastic, and are fitted with holding magnets. All internal and external valve elements are in a RAL gloss 30 finish. Other colours are available on request. QUICK SELECTION ATV-S [m³/h] Orion-ATV-S 25 db(a) 30 db(a) 35 db(a) Dim * Table 5, The table provides the air flow rates with damper open. (*400 without damper) Fig. 4, Orion-ATV with side entry spigot (Ø ) w/damper ORDER CODE, Orion-ATV-S Orion-ATV - K - TA - S / 0 SL = Special finish Front-panel pattern: K = Square, standard S = Circular, custom For ceiling types: Dimension: Ø160 - Ø400 TA = A-flange DC = Dampa Clip-In DG = Dg-flange Spigot: : DS = Ds-flange S = Side, Ø400 without damper EK24 = E-flange-T24 EK15 = E-flange-T15 Orion-ATV-K-TA-S-160/0 Orion-ATV-S extract air terminal device with square front pattern, TA flange for inst. in T-profile ceiling. Standard top-entry spigot, dim. Ø160. Fig. 5, Orion-ATV with side entry spigot (S) Ø400 without damper. A-kant Dampa Clip-In Dg-kant Ds-kant E-kant T24/T15 18 Fig. 6, Ceiling types

19 RIA-SA RIA-SA is an extract-air louvre ideal for high air flow rates. RIA-SA is made from extruded aluminium profiles. DIMENSIONS AND WEIGHT, RIA-SA Weight: approx. 15 kg/m². Minimum dimension: 200 x 200 Maximum dimension, not split: 2000 x RIA-SA is made from extruded, seawater resistant aluminium profiles (EN- AW-6060-T66 / EN-AW-6063-T6), and comes in an RAL gloss 30 finish as standard. The unit can also be delivered in anodized brown, black or natural. Alternative materials or enamel finish are available on request. H-4 ORDER CODE, RIA-SA Product B = Width H = Height RIA-SA / 0 RIA-SA / 0 RIA-SA extract-air louvre. Width 600 and height 800. E = Anodized SL = Special finish Fig.1 B-4 INSTALLATION RIA-SA is designed for wall mounting. Upside down installation of the louvre is recommended to avoid see-through issues. 35 CALCULATION DIAGRAMS MAINTENANCE Unit can be cleaned with a damp cloth Free area = gross area x factor ENVIRONMENT Enquiries regarding product declaration can be directed to our sales team, or information can be found at our website: Height [mm] Diagram 1- RIA-SA 19

20 RIA RIA is an intake and exhaust louvre for external installation. B-4 85 RIA-1 is made from extruded aluminium profiles, and is equipped with animal-proof netting. The RIA-2 design is identical to RIA-1, but without a flange. RIA-3 is made of aluminium, and has insulated blades and animal-proof netting. Wall-mounting frame with anchor is available for RIA-1. H-4 RIA-1 and RIA-2 are made from extruded profiles in seawater resistant aluminium (EN-AW-6060-T66 / EN-AW-6063-T6). Delivered untreated as standard. Can also be delivered in anodized brown, black or natural. The louvres can also be supplied in painted finish. Other materials available on request. RIA-3 is made of seawater resistant aluminium (EN-AW-5052-H34), and is insulated with mineral wool with a glass fibre layer. Painted finish or alternative material available on request. Separate wall-mounting frame comes in an aluminium or galvanized steel design, and is equipped with anchor. Fig. 2, RIA Product ORDER CODE, RIA 1 = Standard frame profile 2 = For embedded installation 3 = Sound absorbing design B = Witdh RIA / / 0 E = Anodized L = Painted finish G = Equipped with KSA guide slip M = Wall-mounting frame VK = Heating cable H = Height H-4 RIA / 0-0-0/ 0 RIA-1 standard frame profile, 500 width, 800 height. B-4 35 DIMENSIONS AND WEIGHT, RIA Specified size = order dimensions (B x H). Products are supplied undersized for installation at duct end and/or in groove as illustrated in figures: B and H. Weight: RIA-1 and 2, approx. 15kg/m² without wall-mounting frame and 20 kg/m² with wall-mounting frame. RIA-3 approx. 45 kg/m2. Max dim. RIA-1, RIA-2 and RIA-3, not split: 2000 x 2000 mm. Fig. 3, RIA-3 Min. hight RIA3: 380mm 84 H+50 B/H-4 B Fig. 1, RIA-1 Fig. 4: Wall-mounting frame for RIA

21 OVA OVA is designed for use as a transfer and extract air unit. The grille is non see-through, and does not require an accurately dimensioned groove. OVA consist of a frame and fixed blades. Pre-drilled mounting holes are provided in the frame. The grille is made in extruded aluminium, and comes in a RAL gloss 30 finish. Alternative colours are available on request. QUICK SELECTION OVA [m³/h] Dim. 10 Pa 15 Pa 20 Pa DIMENSIONS AND WEIGHT, OVA Description BxH Weight [Nom. dim.] [mm] [kg] 200x x100 0,3 300x x100 0,4 300x x144 0,5 300x x202 0,6 400x x100 0,5 400x x144 0,6 400x x202 0,8 500x x144 0,8 500x x202 1,0 500x x246 1,1 500x x304 1,3 600x x202 1,1 600x x304 1,6 600x x392 1,9 600x x500 2,3 600x x600 2,7 Table 2 Table 1: The table shows flow rates at given pressure loss. ORDER CODE, OVA OVA / 0 Product B = Width from and incl. 100, max. 600 H = Height from and incl. 100, max. 600 OVA / 0 OVA - Width: 300, Height: 200 SL = Special finish Figur 1 21

22 LOV LOV is a sound attenuated transfer unit with telescopic feed through for wall mounting LOV is made up of front panels in painted finish and a telescopic feed-through with sound mufflers for wall mounting. The system offers infinitely variable adjustment for wall thickness adaptation. DIMENSIONS AND WEIGHT, LOV Type A B T Groove Weight [kg] x 110 4, x 110 5, x 110 6, x 110 6,3 Table 2 LOV s front panels are made in steel, and come in a RAL gloss 30 finish. Other colours are available on request. The telescopic frame is in galvanised steel and the sound mufflers are isolated with sound absorber in polyester. QUICK SELECTION Sound level LOV [m³/h] difference Type 10Pa 15Pa 20Pa Dn,e,w Table 1: The table shows air flow rates at L WA <30dB(A). Fig. 1 ORDER CODE, LOV LOV / LT / 0-0 Product SL = Special finish Type : SM = Special material 612, 613, 812 or 813 LT = Light-proof design LOV-613 / LT / 0-0 LOV type 613, light-proof design 22

23 VSR VSR is designed for use as an air inlet unit in areas exposed to adverse weather conditions. Can be installed in external wall or roof unit. DIMENSIONS AND WEIGHT, VSR Recommended dimensions: from 600 x 600 to 2000 x Module 50 mm. Millimetre adjustment on request. Weight: approx. 30 kg/m 2. VSR is equipped with vertical blades. The drainage chamber features external drainage, but is available with internal drainage if required. VSR is delivered with the flange unattached. B VSR is made of seawater-resistant aluminium. (EN-AW-5052-H34) H+95 H-7 ORDER CODE, VSR H/3 49 VSR / B-7 47 Product L = Enamel finish B = Width SM = Special material H = Height Drainage chamber VSR / 0-0 VSR Width: 1200, Height: 1600 All dimensions in mm. Groove dimensions: B x H + 5 mm Fig. 1 23

24 TOG-R TOG-R is a circular transfer unit for wall mounting, and is used for inter-room air transfer, such as from living room to corridor, using a central outlet. TOG-R comprises two mounting rings and two sound attenuating diffuser fronts which are installed on each side of the wall. The mounting rings feature a clip-on system for easy fitting of the front units. DIMENSIONS AND WEIGHT, TOG-R Type A C Weight [kg] , , ,2 Table 2 Both the diffuser front and the mounting ring are made in steel, with a RAL gloss 30 finish. Other colours available on request. QUICK SELECTION Sound level TOG-R [m³/h] difference Type 10Pa 15Pa 20Pa Dn,e,w Table 1: The table shows air flow rates at max slot height, L WA < 30 db(a). Fig. 1 ORDER CODE, TOG-R TOG-R / 0 Product Type: SL = Special finish TOG-R-160 / 0 TOG-R transfer unit, type

25 Pegasus Comfort Pegasus Comfort is a wall diffusor with VAV functionality and a heating coil. It is used as a volume regulator and air inlet unit in demand controlled ventilation systems. Pegasus Comfort has very good induction, which makes it well-suited for variable airflows. FUNCTION Pegasus Comfort has a built-in VAV regulator for demand control of the airflow. The damper solution will choke the pressure at high flow rates and will maintain a low sound level. This may reduce the need for additional dampers and sound attenuators in a duct system.the unit is equipped with a heating coil for waterborne heating of inlet air. Pegasus Comfort is delivered with Belimo MP Bus, LON, Modbus or Belimo KNX for direct bus communications with building automation systems. Pegasus Comfort is built as a complete measurement and regulating unit for demand control of the airflows in the ventilation system. The measurement station measures pressure difference via measurement rods integrated into the unit. The unit is equipped with an LHV-D3 VAV regulator from Belimo. The regulator's specifications are found in the table below. Complete technical documentation can be downloaded from The unit has a simple connection and service point on the outside of the box s side. See figure 10. Pegasus Comfort has a detachable front plate with selectable LØV- or Opus execution. LØV has 2 different patterns, long (L) or short (K) air throw. If Opus pattern is selected with turnable plastic nozzles, the designation (V) is for variable air throw. Pipe connection water side is delivered as standard with Ø15 smooth pipe. They can also be ordered with 1/2 internal or external threads. Actuator LHV-D3-MP/MOD/LON Operating voltage AC 24 V 50/60 Hz, DC 24 V Power consumption 2.5W Dim power 4.5VA (max.8 ms) Table 1, Technical specification, Belimo VAV controller MATERIALS AND FINISH Pegasus Comfort is made of galvanised steel. The measurement cross is in aluminium, hoses and nipples are in plastic. The damper has an affixed polyester cloth. The spigot has a rubber EPDM seal. Battery made of copper and aluminium. The K and L type front panels are made of steel with a RAL gloss 30 finish. Other colours are available on request. The V type diffuser front features Opus nozzles in ABS plastic, is made of steel and comes in a RAL gloss 30 finish. Other colours are also available, but without theadjustable nozzle option Short throw length (LØV) REGULATION RANGE, PEGASUS-COMFORT Pegasus-Comfort (m³/h) Dim. Minimum Maximum Table 3, Regulation range for VAV, airflow in m³/h. See dimensioning diagram for sound power and pressure loss. ORDER CODE Connection: B = Rear edge S = Side Dim. Ø125 - Ø250 Normal operating range for Pegasus Comfort Distance to opposite wall (m) Long throw length (LØV) Pegasus Comfort - B / L / 0 / IG / 0 Front, type: K = LØV perforation, short air throw L = LØV perforation, long air throw V = Opus nozzles, variable distribution pattern Variable throw length (OPUS) SL = Special lacquer Pipe connection Water side: 0 = Smooth pipes IG = Internal ½" threads UG = External ½" threads Connection: 0 = MP-Bus 2 = LON-Bus 3 = MOD-Bus 4 = MP-Bus with EasyLink plug 7 = Belimo KNX 8 = MOD-Bus for X-AIRCONTROL Pegasus-B-125/L/0/IG/0 Pegasus Comfort for rear connection, dim Ø125. LØV front plate with long air throw and MP-Bus actuator. Pipe connection on the water side is fitted with an internal ½" thread. 25

26 QUICK SELECTION PEGASUS-COMFORT LØV-B-K/L Pegasus-Comfort LØV-B-K/L m³/h (open) Dim. 25 db(a) 30 db(a) 35 db(a) QUICK SELECTION PEGASUS-COMFORT OPUS-B Pegasus-Comfort Opus-B m³/h (open) Dim. 25 db(a) 30 db(a) 35 db(a) QUICK SELECTION PEGASUS-COMFORT LØV-S-K/L Pegasus-Comfort LØV-B-K/L m³/h (open) Dim. 25 db(a) 30 db(a) 35 db(a) Table 2, Quick selection Pegasus Comfort QUICK SELECTION PEGASUS-COMFORT OPUS-S Pegasus-Comfort Opus-S m³/h (open) Dim. 25 db(a) 30 db(a) 35 db(a) DIMENSIONS AND WEIGHT, PEGASUS COMFORT Dim. D BF HF BK BK2 HK DS A B E F G H I J Weight [Kg] Table 4 Figure 2, Dimensional sketch Pegasus Comfort-B 26

27 Pegasus Comfort Figure 3, Dimensional sketch Pegasus Comfort-S LØV-K LØV-L OPUS Figure 4, Pegasus Comfort fronts 27

28 Opus-4 and Opus-5 Opus-4 and Opus-5 are rectangular supply diffusers fitted to the side of circular and rectangular air ducts. The diffusers offer an adjustable flow pattern and are ideal for both under- and overheated air. Duct velocity ahead of the first diffuser should not exceed 5 m/s. Opus-4D and 4DD are made for installation in circular ducts, whereas Opus-5D and 5DD are designed for installation in rectangular ducts. The diffusers are equipped with adjustable Opus nozzles. Each unit is fitted with a diffuser plate to the rear which ensures even distribution at the front. The system is available with one (D) or two (DD) nozzle rows. In addition to the standard dimensions, made-to-measure diffusers with different numbers of nozzles are also available. Please contact your local dealer for more information. The standard nozzle settings are shown in fig. 1. DIMENSIONS AND WEIGHT, Opus-4 and Opus-5 Opus-4D with single nozzle row is suitable from and incl. dim. Ø200 to and incl. dim. Ø1000. Opus-4DD with double nozzle row is suitable from and incl. dim. Ø315 to and incl. dim. Ø1250. Product Weight [kg] Groove dimensions [mm] Opus-4D 1,3 950 x 70 Opus-5D 1,3 950 x 70 Opus-4DD 1,7 950 x 125 Opus-5DD 1,7 950 x 125 Table 2 The diffusers are steel plated, with a RAL gloss 30 finish. Opus nozzles are in ABS plastic. Black RAL 9005, aluminium RAL 9006 and galvanised design can be provided on request. Other colours are also available, but without adjustable nozzles. QUICK SELECTION Opus 4 and Opus-5 Product [m³/h] Type 25 db(a) 30 db(a) 35 db(a) Opus 4/5D Opus 4/5DD Table 1: The table shows airflow rates at given sound power levels. (Duct velocity ahead of first diffuser 5 m/s). ORDER CODE Opus - 4 / DD / 315 / 0 SL = Special finish Type: G = Galvanized 4 = For circular duct 0 = RAL gloss 30 5 = For rectangular duct Dim: Ø200 - Ø1250 D = Single row of nozzles. DD = Double row of nozzles MA = Special dimensions and number of nozzles Fig. 1 Exsemple: Opus-4 / DD / 315 / 0 Opus-4 for circular duct, double row of nozzles, dimension Ø315 finished in RAL gloss

29 Pegasus Pegasus is a wall diffuser unit with VAV function. It is used as a volume flow controller unit in demand controlled ventilation systems. Pegasus has very good induction, making it ideal for variable air flow rates. FUNCTION Pegasus has a built-in VAV controller for the demand controlled adjustment of air flow rates. The damper solution will choke the pressure at high flow rates and maintain a low sound level. This may reduce the need for additional dampers and sound attenuators in a duct system. Pegasus is supplied with Belimo MP-Bus, LON, Modbus or Belimo KNX for direct BUS communication with SD systems. Pegasus is a complete measuring and control unit for the demand control of air flow rates in ventilation systems. The measuring station measures the differential pressure using measuring rods integrated into the unit. The unit is equipped with an LHV-D3 VAV controller from Belimo. The controller's specifications are provided in the table below. Full technical documentation can be downloaded from eu. Pegasus has a removable front panel with a choice of LØV or Opus design. LØV has two different designs, long (L) or short (K) throw length. If the Opus design with turnable plastic nozzles is selected, (V) is the designation for the variable throw length. MATERIALS AND FINISH Pegasus is made of galvanised steel. The measuring cross is made of aluminium, hoses and nipples are made of plastic. The damper is fitted with a polyester cloth. The connection collar has an EPDM rubber gasket. Actuator Operating voltage Power consumption Dim. power LHV-D3-MP/MOD/LON AC 24 V 50/60 Hz, DC 24 V 2.5 W 4.5 VA (max. 8 ms) Table 1, Technical specification, Belimo VAV controller Figure 1 ORDER CODE Pegasus - B / L / 0 / 0 Connection: B = Rear edge S = Side Dim Front, type: K = LØV perforation, short throw length L = LØV perforation, long throw length V = Opus nozzles variable distribution pattern SL = Special lacquer 0 = MP-Bus 1 = MP-Bus with VIP-X plug 2 = LON-Bus 3 = MOD-Bus 4 = MP-Bus with EasyLink plug 5 = Stand alone with trafo for CO2 and temperature 6 = Stand alone with trafo for PIR 7 = Belimo KNX 8 = X-AIRCONTROL Pegasus-B-125/L/0/0 Pegasus for rear connection, dim. Ø125 LØV front panel with long throw length with MP Bus actuator without lead plug. 29

30 QUICK SELECTION PEGASUS LØV-B-K/L Pegasus LØV-B-K/L m³/h (open) Dim. 25 db(a) 30 db(a) 35 db(a) QUICK SELECTION PEGASUS LØV-B-K/L Pegasus LØV-B-K/L m³/h (75 Pa) Dim. 25 db(a) 30 db(a) 35 db(a) QUICK SELECTION PEGASUS LØV-S-K/L Pegasus LØV-S-K/L m³/h (open) Dim. 25 db(a) 30 db(a) 35 db(a) QUICK SELECTION PEGASUS LØV-S-K/L Pegasus LØV-S-K/L m³/h (75 Pa) Dim. 25 db(a) 30 db(a) 35 db(a) QUICK SELECTION PEGASUS OPUS-B Pegasus Opus-B m³/h (open) Dim. 25 db(a) 30 db(a) 35 db(a) QUICK SELECTION PEGASUS OPUS-S Pegasus Opus-S m³/h (open) Dim. 25 db(a) 30 db(a) 35 db(a) QUICK SELECTION PEGASUS OPUS-B Pegasus Opus-B m³/h (75 Pa) Dim. 25 db(a) 30 db(a) 35 db(a) QUICK SELECTION PEGASUS OPUS-S Pegasus Opus-S m³/h (75 Pa) Dim. 25 db(a) 30 db(a) 35 db(a) Table 2, Quick selection table Pegasus REGULATION RANGE, PEGASUS Pegasus (m³/h) Dim. Minimum Maximum Table 3, Adjustment range for VAV, air flow rate in m³/h. See calculation diagram for sound power level and pressure drop 30

31 Pegasus DIMENSIONS AND WEIGHT, PEGASUS Dim. D BF HF BK BK2 HK DB DS A B Weight [kg] Table 4 Figure 2, Dimensioned sketch Pegasus-B Figure 3, Dimensioned sketch Pegasus-S Figure 4, Pegasus fronts 31

32 Orion-LØV with Sirius Comfort Sirius Comfort is a diffusor unit with VAV and heating functions. It is used as a volume regulator and diffusor unit in demand cotrolled ventilation systems. Sirius Comfort has unique characteristics, that is well-suited for variable airflows and contributes to the valve's very good induction. FUNCTION Sirius Comfort has a built-in VAV regulator for demand control of airflows. The damper solution will choke the pressure at high flow rates and will maintain a low sound level. This may reduce the need for additional dampers and sound attenuators in a duct system. The unit is equipped with a heating coil for waterborne heating of inlet air. Sirius Comfort is delivered with Belimo MP Bus, LON, Modbus or Belimo KNX for direct bus communications with building automation systems. Measurement deviation for the area: 10-20% of nominal: ±25% 20-40% of nominal: <±10% % of nominal: <±4% At T-pipe situation, a distance of at least 5 x ØD is recommended in order to maintain same measurement precision. ORDER CODE Orion-LØV-Sirius-Comfort TA B SL=Special lacquer False ceiling: TA=A-Edge DC=Dampa Clip-In DG=Dg-edge DS=Ds-edge Dim: Ø200 Ø250 Ø315 Ø400 EK 24=E-edge-T24 EK 15=E-edge-T15 B=Motion sensor (Connection 4 and 6) Orion-LØV-Sirius-Comfort-TA-B-200/0 Orion-LØV-Sirius-Comfort air inlet valve with buckling edge A for T profile ceiling Motion sensor in valve front, connection valve Ø200 Sirius Comfort is built as a complete measurement and regulating unit for demand control of airflows in the ventilation system. The measurement station measures pressure difference via measurement rods integrated into the unit. The unit is equipped with an LHV-D3 VAV regulator from Belimo. The controller s specifications are found in the table below. Complete technical documentation can be downloaded from Orion-LØV has a detachable front plate with LØV perforation, and can be delivered adapted to different types of ceiling systems. Pipe connection water side is delivered as standard with Ø15 smooth pipe. They can also be ordered with 1/2 internal or external threads. Actuator LHV-D3-MP/MOD/LON Operating voltage AC 24 V 50/60 Hz, DC 24 V Power consumption 2.5W Dim power 4.5VA (max.8 ms) Table 1, Technical specification, Belimo VAV controller. MATERIALS AND FINISH Sirius Comfort is made of galvanised steel. The measurement cross is in aluminium, hoses and nipples are in plastic. The damper has an affixed polyester cloth. The spigot has a rubber EPDM seal. Heating coil is copper and aluminium. QUICK SELECTION ORION-LØV WITH SIRIUS COMFORT Orion-Løv with Sirius Comfort m³/h (open) ØD 25 db(a) 30 db(a) 35 db(a) Table 2, Quick selection Orion LØV with Sirius Comfort Sirius Comfort Pipe connection water side: 0 = Smooth pipe IG = Internal ½" threads Dim: UG = External ½" threads Connection: = MP-Bus = MP-Bus with VIP-X plug 2 = LON-Bus 3 = MOD-Bus 4 = MP-Bus with EasyLink plug 5 = Stand alone with transformator for CO2 and temperature 6 = Stand alone with transformator for PIR/potential-free switch 7 = Belimo KNX 8 = MOD-Bus for X-AIRCONTROL Sirius Comfort Sirius Comfort with intake Ø125 and outlet Ø200, with MP-Bus regulator, smooth pipe connection on water side. QUICK SELECTION ORION-LØV WITH SIRIUS COMFORT Orion-Løv with Sirius Comfort m³/h (75Pa) Dim. 25 db(a) 30 db(a) 35 db(a)

33 ORDER CODE REGULATION RANGE Sirius (m³/h) ØD Minimum Maximum Table 3. Regulation range for vav regulator, airflow in m3/h. See dimensioning diagram for sound power and pressure loss. Orion-PTV-Sirius-Comfort TA B 200 SCK SL = Special lacquer False ceiling: TA=A-edge SCK DC=Dampa Clip-In DG=Dg-edge DS=Ds-edge EK 24=E-edge-T24 SCK=Sirius Comfort Intake-outlet Pipe connection water side: 0 = Smooth pipe IG = Internal ½" threads EK 15=E-edge-T UG = External ½" threads B=Motion sensor (Connection 4 and 6) Connection: 0 = MP-Bus Dim: Ø200,Ø250,Ø315,Ø = MP-Bus with VIP-X plug 2 = LON-Bus 3 = MOD-Bus 4 = MP-Bus with EasyLink plug 5 = Stand alone with transformator for CO2 and temperature 6 = Stand alone with transformator for PIR/potential-free switch 7 = Belimo KNX 8 = MOD-Bus for X-AIRCONTROL Orion-PTV-Sirius-Comfort-TA-B-200-SCK /0 Orion-PTV-Sirius air intake valve with buckling edge A for T-profile, motion sensor in valve front, connection valve Ø200, Sirius chamber intake Ø125 og outlet Ø200, with MP-Bus regulator, smooth pipe connection on water side. 0 DIMENSIONS AND WEIGHT Dim. D DA B H L E F Weight [Kg] * ** Table 4. Sirius Comfort dimensions and weight table. *) 185 with the coil pipe parts are mounted on the left **) 220 with the coil pipe parts are mounted on the left Figur 1, Orion LØV with Sirius Comfort Dimensional sketch 33

34 Orion Opus with Sirius Comfort Orion-Opus with Sirius Comfort is a diffusor unit with VAV functionality and a heating function. It is used as a volume regulator and diffusor unit in demand controlled ventilation systems. Sirius Comfort has unique characteristics and Orion-Opus has a large capacity, good induction and is well-suited to large airflows. FUNCTION Sirius Comfort has a built-in VAV regulator for demand control of airflows. The damper solution will choke the pressure at high flow rates and will maintain a low sound level. This may reduce the need for additional dampers and sound attenuators in a duct system.the unit is equipped with a heating coil for waterborne heating of inlet air. Sirius Comfort is delivered with Belimo MP Bus, LON, Modbus or Belimo KNX for direct bus communications with building automation systems. Measurement deviation for the area: 10-20% of nominal: ±25% 20-40% of nominal: <±10% % of nominal: <±4% At T-pipe situation, a distance of at least 5 x ØD is recommended in order to maintain same measurement precision. ORDER CODE Orion-OPUS-Sirius-Comfort TA B SL=Special lacquer False ceiling: TA=A-Edge DC=Dampa Clip-In DG=Dg-edge DS=Ds-edge Dim: Ø200 Ø250 Ø315 Ø400 EK 24=E-edge-T24 EK 15=E-edge-T15 B=Motion sensor (Connection 4 and 6) Orion-OPUS-Sirius-Comfort-TA-B-200/0 Orion-OPUS-Sirius-Comfort air inlet valve with buckling edge A for T profile ceiling, Motion sensor in valve front, connection valve Ø200 Sirius Comfort is built as a complete measurement and regulating unit for demand control of airflows in the ventilation system. The measurement station measures pressure difference via measurement rods integrated into the unit. The unit is equipped with an LHV-D3 VAV regulator from Belimo. The controller s specifications are found in the table below. Complete technical documentation can be downloaded from Orion-Opus has a detachable front plate with nozzles of ABS plastic, and can be delivered adapted for different types of ceiling systems. Pipe connection water side is delivered as standard with Ø15 smooth pipe. They can also be ordered with 1/2 internal or external threads. Actuator LHV-D3-MP/MOD/LON Operating voltage AC 24 V 50/60 Hz, DC 24 V Power consumption 2.5W Dim power 4.5VA (max.8 ms) Table 1, Technical specification, Belimo VAV Controller. Sirius Comfort Pipe connection water side: 0 = Smooth pipe IG = Internal ½" threads Dim: UG = External ½" threads Connection: = MP-Bus = MP-Bus with VIP-X plug 2 = LON-Bus 3 = MOD-Bus 4 = MP-Bus with EasyLink plug 5 = Stand alone with transformator for CO2 and temperature 6 = Stand alone with transformator for PIR/potential-free switch 7 = Belimo KNX 8 = MOD-Bus for X-AIRCONTROL Sirius Comfort Sirius Comfort with intake Ø125 and outlet Ø200, with MP-Bus regulator, smooth pipe connection on water side. MATERIALS AND FINISH Sirius Comfort is made of galvanised steel. The measurement cross is in aluminium, hoses and nipples are in plastic. The damper has an affixed polyester cloth. The spigot has a rubber EPDM seal. Heating coil is copper and aluminium. QUICK SELECTION ORION-OPUS WITH SIRIUS COMFORT Orion-Løv with Sirius Comfort m³/h (open) Dim. 25 db(a) 30 db(a) 35 db(a) Table 2, Quick selection Orion-Opus with Sirius Comfort. QUICK SELECTION ORION-OPUS WITH SIRIUS COMFORT Orion-Løv with Sirius Comfort m³/h (75Pa) Dim. 25 db(a) 30 db(a) 35 db(a)

35 ORDER CODE Orion-Opus-Sirius-Comfort TA B 200 SCK 0 REGULATION RANGE Sirius (m³/h) Dim. Minimum Maximum Table 3. Regulation range for vav regulator, airflow in m3/h. See dimensioning diagram for sound power and pressure loss. SL = Special lacquer False ceiling: TA=A-edge SCK DC=Dampa Clip-In DG=Dg-edge DS=Ds-edge EK 24=E-edge-T24 SCK=Sirius Comfort Intake-outlet Pipe connection water side: 0 = Smooth pipe IG = Internal ½" threads EK 15=E-edge-T15 UG = External ½" threads B=Motion sensor Connection: (Connection 4 and 6) = MP-Bus Dim: Ø200,Ø250,Ø315,Ø = MP-Bus with VIP-X plug 2 = LON-Bus 3 = MOD-Bus 4 = MP-Bus with EasyLink plug 5 = Stand alone with transformator For CO2 og temperature 6 = Stand alone with transformator for PIR/potential-free switch 7 = Belimo KNX Orion-Opus-Sirius-Comfort-TA-B-200-SCK /0 8 = MOD-Bus for X-AIRCONTROL Orion-Opus-Sirius air intake valve with buckling edge A for T-profil, motion sensor in valve front, connection valve Ø200, Sirius chamber intake Ø125 and outlet Ø200, with MP-Bus regulator, smooth pipe connection on water side. DIMENSIONS AND WEIGHT Dim. D DA B H L E F Weight [Kg] * ** Table 4. Sirius Comfort dimensions and weight table. *) 185 with the coil pipe parts are mounted on the left **) 220 with the coil pipe parts are mounted on the left Figure 1, Orion Opus with Sirius Comfort - Dimensioned sketch 35

36 Orion-PTV with Sirius Comfort Orion-PTV with Sirius Comfort is a diffusor unit with VAV and heating functions. It is used as a volume regulator and diffusor unit in demand controlled ventilation systems. Sirius Comfort has unique characteristics and Orion-PTV has a large capacity, good induction and is wellsuited for the inlet of large airflows. FUNCTION Sirius Comfort has a built-in VAV regulator for demand control of airflows. The damper solution will choke the pressure at high flow rates and will maintain a low sound level. This may reduce the need for additional dampers and sound attenuators in a duct system.the unit is equipped with a heating coil for waterborne heating of inlet air. Sirius Comfort is delivered with Belimo MP Bus, LON, Modbus or Belimo KNX for direct bus communications with building automation systems. Measurement deviation for the area: 10-20% of nominal: ±25% 20-40% of nominal: <±10% % of nominal: <±4% At T-pipe situation, a distance of at least 5 x ØD is recommended in order to maintain same measurement precision. ORDER CODE Orion-PTV-Sirius-Comfort TA B SL=Special lacquer False ceiling: TA=A-Edge DC=Dampa Clip-In DG=Dg-edge DS=Ds-edge Dim: Ø200 Ø250 Ø315 Ø400 EK 24=E-edge-T24 EK 15=E-edge-T15 B=Motion sensor (Connection 4 and 6) Orion-PTV-Sirius-Comfort-TA-B-200/0 Orion-PTV-Sirius-Comfort air inlet valve with buckling edge A for T profile ceiling. Motion sensor in valve front, connection valve Ø200 Sirius Comfort is built as a complete measurement and regulating unit for demand control of airflows in the ventilation system. The measurement station measures pressure difference via measurement rods integrated into the unit. The unit is equipped with an LHV-D3 VAV regulator from Belimo. The controller s specifications are found in the table below. Complete technical documentation can be downloaded from Orion-PTV has a detachable front plate with a perforated front and side edges on the valve, and can be delivered adapted for different types of ceiling systems. Pipe connection water side is delivered as standard with Ø15 smooth pipe. They can also be ordered with 1/2 internal or external threads. Actuator LHV-D3-MP/MOD/LON Operating voltage AC 24 V 50/60 Hz, DC 24 V Power consumption 2.5W Dim power 4.5VA (max.8 ms) Table 1, Technical specification, Belimo VAV Controller. Sirius Comfort Pipe connection water side: 0 = Smooth pipe IG = Internal ½" threads Dim: UG = External ½" threads Connection: = MP-Bus = MP-Bus with VIP-X plug 2 = LON-Bus 3 = MOD-Bus 4 = MP-Bus with EasyLink plug 5 = Stand alone with transformator for CO2 and temperature 6 = Stand alone with transformator for PIR/potential-free switch 7 = Belimo KNX 8 = MOD-Bus for X-AIRCONTROL Sirius Comfort Sirius Comfort with intake Ø125 and outlet Ø200, with MP-Bus regulator, smooth pipe connection on water side. MATERIALS AND FINISH Sirius Comfort is made of galvanised steel. The measurement cross is in aluminium, hoses and nipples are in plastic. The damper has an affixed polyester cloth. The spigot has a rubber EPDM seal. Heating coil is copper and aluminium. QUICK SELECTION ORION PTV WITH SIRIUS COMFORT Orion-PTV with Sirius Comfort m³/h (open) Dim. 25 db(a) 30 db(a) 35 db(a) QUICK SELECTION ORION PTV WITH SIRIUS COMFORT Orion-PTV with Sirius Comfort m³/h (75Pa) Dim. 25 db(a) 30 db(a) 35 db(a) Table 2, Quick selection Orion PTV with Sirius Comfort. 36

37 ORDER CODE Orion-PTV-Sirius-Comfort TA B 200 SCK 0 REGULATION RANGE Sirius (m³/h) Dim. Minimum Maximum Table 3. Regulation range for vav regulator, airflow in m3/h. See dimensioning diagram for sound power and pressure loss. SL = Special lacquer False ceiling: TA=A-edge SCK DC=Dampa Clip-In DG=Dg-edge DS=Ds-edge EK 24=E-edge-T24 SCK=Sirius Comfort Intake-outlet Pipe connection water side: 0 = Smooth pipe IG = Internal ½" threads EK 15=E-edge-T UG = External ½" threads B=Motion sensor (Connection 4 and 6) Connection: 0 = MP-Bus Dim: Ø200,Ø250,Ø315,Ø = MP-Bus with VIP-X plug 2 = LON-Bus 3 = MOD-Bus 4 = MP-Bus with EasyLink plug 5 = Stand alone with transformator for CO2 and temperature 6 = Stand alone with transformator for PIR/potential-free switch 7 = Belimo KNX 8 = MOD-Bus for X-AIRCONTROL Orion-PTV-Sirius-Comfort-TA-B-200-SCK /0 Orion-PTV-Sirius air intake valve with buckling edge A for T-profile, motion sensor in valve front, connection valve Ø200, Sirius chamber intake Ø125 og outlet Ø200, with MP-Bus regulator, smooth pipe connection on water side. DIMENSIONS AND WEIGHT Dim. D DA B H L E F Weight [Kg] * ** Table 4. Sirius Comfort dimensions and weight table *) 185 with the coil pipe parts are mounted on the left **) 220 with the coil pipe parts are mounted on the left Figure 1, Orion PTV with Sirius Comfort - Dimensioned sketch 37

38 TLH TLH is a basic supply diffuser for wall, ceiling or riser installation. TLH features a perforated front and a connection collar fitted with a wide rubber gasket for installation directly in duct or groove without additional fastening devices. DIMENSIONS AND WEIGHT, TLH Dim. D DA A B Weight [kg] Table 2 TLH is made of steel, and comes in a RAL gloss 30 finish with EPDM rubber gasket fitted as standard. ODA QUICK SELECTION TLH [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Table 1: The table shows the air volume at 3 sound levels. The sound level is Lw(A). ORDER CODE, TLH TLH / 0 Product Dimension: Ø100 - Ø160 TLH-125 / 0 TLH supply diffuser dim. Ø125. SL = Special finish OD A B Fig.1 38

39 LØV-R LØV-R is a circular supply diffuser for ceiling mounting. LØV offers excellent induction and is suitable for both constant and variable volume flow. LØV-R features a removable front panel with LØV perforation. The diffuser front plate are made in steel. The diffuser body is in aluminium and is fitted with an EPDM rubber gasket at the connection collar. All internal and external diffuser elements are finished in RAL gloss 30. Other colours are available on request. DIMENSIONS AND WEIGHT, LØV-R Dim. A B C G E F I Weight diffuserl [kg] , , , , , ,7 Table 2 QUICK SELECTION LØV-R [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Table 1. The table shows air flow rates at given sound power levels. ORDER CODE, LØV (LOEV-R) LØV-R LOEV-R Explantation: LOEV-R, standard dimension Ø160 SL = Special finish. Dimension: Ø Fig. 1 ORDER CODE, Luna UI = Outlet installed, low profile design I = Insulated Luna Dimension outlet: Ø100 Ø315 Dimension inlet: Ø100 Ø315 Luna Explantation: Luna plenum box with inlet Ø125 and outlet Ø160 39

40 LØV-R with Luna plenum box The Luna plenum box is recommended for improved sound attenuation, and provides an adjustment and measurement option. Luna is a rectangular box with a removable damper providing access to the connecting duct. The damper can be locked in the position required. The Luna plenum box features a damper and measurement device for adjustment. It is insulated with a sound absorber in polyester and is available with one or two dimensional changes between inlet and outlet. Furthermore, the box can be supplied with external condensation insulation. A low-profile design [UI] is also available, and for this design a reduction in capacity of approx. 20% will apply. The distance between diffuser and box can be increased by up to 35 cm without extending the wire and measuring tube. Luna is supplied in a galvanised finish, and with four internal walls lined with a sound absorber in polyester. The connection collar is fitted with an EPDM rubber gasket. QUICK SELECTION DIMENSIONS S AND WEIGHT, Luna Dim. D DA B H H1 H2 L L1 L2 Weight Luna [kg] , , , , , , , , , , , , , , Table 4 LØV-R Luna [m³/h] Dim. Dim. 25 db(a) 30 db(a) 35 db(a) Table 3. The table shows air flow rates at given sound power levels and 50 Pa total pressure loss. ORDER CODE, LØV-R (LOEV-R) with Luna LØV-R-L-0 SL = Special finish Fig. 2 L L = Luna UI = Outlet installed, low profile design RH = Plenum box for fixed ceiling plate I = Insulated Dimension outlet: Ø100 Ø315 Dimension inlet: Ø100 Ø315 LOEV-R-L Explantation: LOEV-R diffuser and Luna plenum box inlet Ø125 and outlet/diffuser dim. Ø

41 TLG-LØV TLG-LØV is a circular supply diffuser for ceiling mounting. TLG-LØV offers excellent induction, and is suitable for both constant and variable air flow rates. TLG-LØV features a front panel with LØV perforation and adjustable slot height. The diffuser and ceiling plate are in a steel design, and the connection collar is equipped with an EPDM rubber gasket. All internal and external diffuser elements come in a RAL gloss 30 finish. Other colours are available on request. DIMENSIONS AND WEIGHT, LØV-R Dim. A B J T Groove Weight dim. diffuser [kg] , , , , , ,0 Table 2 QUICK SELECTION TLG-LØV [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Table 1: The table shows air flow rates at given sound power levels. Maximum slot height and valve fitted directly in straight duct. TLG-LØV OB OA TLG-LØV 250 og 315 OB T J J ORDER CODE, TLG-LØV (TLG-LOEV) TLG-LØV S = Vertical throw pattern E = One-way throw pattern Dimension: Ø100 Ø315 TLG-LOEV Explantation: TLG-LOEV dim. Ø125 SL = Special finish Fig.1 OA T ORDER CODE, Luna Luna UI = Outlet installed, low profile design, I = Insulated Dimension outlet: Ø100 Ø315 Dimension inlet: Ø100 Ø315 Luna Explantation: Luna plenum box with inlet Ø125 and outlet Ø

42 TLG-LØV with Luna plenum box The Luna plenum box is recommended for improved sound attenuation, and works as an adjustment and measurement unit. Luna is a rectangular box equipped with a removable damper which provides access to the connecting duct. The damper can be secured in any position required. Luna plenum box features a damper and measuring outlet for commissioning. It is insulated with sound absorber in polyester and is available with one or two dimensional changes between inlet and outlet. Furthermore, the box can be delivered with external condensation insulation [I]. A lowprofile design [UI] is also available, and for this design a reduction in capacity of approx. 20% will apply. The distance between diffuser and box can be increased by up to 35 cm without extending the wire and measuring tube. Luna is supplied a galvanised finish, and with all four internal walls lined with sound absorber in polyester. The connection collar is fitted with an EPDM rubber gasket. DIMENSIONS AND WEIGHT, Luna Dim. D DA B H H1 H2 L L1 L2 Wight Luna [kg] , , , , , , , , , , , , , , Table 4 QUICK SELECTION TLG-LØV Luna [m³/h] Dim. Dim. 25 db(a) 30 db(a) 35 db(a) Table 3: The table provides air flow rates at given sound power levels and 50 Pa total pressure loss. ORDER CODE, TLG-LØV (TLG-LOEV) with Luna TLG-LØV-0-L-SL S = Vertical throw pattern E = One-way throw pattern SL = Special finish Fig. 2 L L = Luna UI = Outlet installed, low profile design I = Insulated Dimension outlet: Ø100 Ø315 Dimension inlet: Ø100 Ø315 TLG-LOEV-0-L SL Explantation: TLG-LOEV diffuser and Luna plenum box inlet Ø125 and outlet/diffuser dim. Ø160, special finish RAL *Colourcode must be remarked. 42

43 Tellus-LØV Tellus-LØV is a circular supply diffuser for exposed installation. It offers excellent induction and is suitable for both constant and variable air flow rates. The diffuser is also available with pass-through function. Tellus-LØV features a removable front panel with LØV perforation and adjustable slot height. Rotational pattern is supplied as standard. Other flow patterns are available on request. The box is insulated with a sound absorber in polyester and is equipped with measuring outlet and removable airflow adjustment damper. Available in high-profile or low-profile design. The high-profile version is also available in pass-through design as shown in fig. 3. DIMENSIONS AND WEIGHT, Tellus-LØV Dim. D DA H L S Weight [kg] /24 2, /24 2, /29 3, / /28/38 5, /28/38 7 Table 3 The diffuser is made of steel with a RAL gloss 30 finish. Other colours are available on request. It is internally lined with a sound absorber in polyester, and the connection collar is fitted with an EPDM rubber gasket. QUICK SELECTION, Tellus-LØV-H/L Tellus-LØV [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Table 1: The table shows air flow rates at given sound power levels and 30 Pa total pressure loss. Fig. 1, Tellus-LØV-L QUICK SELECTION, Tellus-LØV-H/D Quick selection for maximum slot height of Tellus-LØV type D together with Tellus-LØV-H, as a unit Tellus-LØV HD [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Table 2, The table shows air flow rates at given sound power levels and 30 Pa total pressure loss Fig. 2, Tellus-LØV-H ORDER CODE, Tellus-LØV (LOEV) SL = Special finish D = Pass-through connection Dim: Ø200 - Ø315, type H only Dimension: Ø100 - Ø315 Fig. 3, Tellus-LØV-H-D 43

44 Tellus-Opus Tellus-Opus is a circular supply diffuser with adjustable nozzles for open installation. The diffuser is also available with pass-through function. With its adjustable Opus-nozzle solution, the flow pattern can be regulated and set as required. Tellus-Opus features a removable front panel with Opus nozzles and adjustable slot height. Rotational pattern is supplied as standard. Other flow patterns are available on request. The box is insulated with a sound absorber in polyester and is equipped with a measuring outlet and removable airflow adjustment damper. Also available as a passtrough unit as shown in fig.2. DIMENSIONS AND WEIGHT, Tellus-Opus Dim. D DA H L S Weight [kg] /29 3, /29 4, /28 6, /28 10,2 Table 3 The diffuser is made of steel and comes in a RAL gloss 30 finish. Black RAL 9005 and aluminium RAL 9006 are available on request. Other colours can be supplied, but without the nozzle-adjustment option. Opus-nozzles are in ABS plastic. The box is internally lined with a sound absorber in polyester, and the connection collar is fitted with an EPDM rubber gasket. QUICK SELECTION Tellus-Opus Tellus-Opus [m³/h] Dim. Damper 25 db(a) 30 db(a) 35 db(a) 125 max max max max Table 1: The table shows air flow rates at given sound power levels and 30 Pa total pressure loss with maximum open damper. QUICK SELECTION Tellus-Opus-D Quick selection for maximum slot height of Tellus-Opus type D and Tellus-Opus, together as one unit Tellus-Opus-D [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Table 2: The table shows air flow rates at given sound power levels and 30 Pa total pressure loss. Fig. 1 ORDER CODE, Tellus-Opus Tellus-Opus -125 / 0 / 0 Product SL =Special finish Dimension: Ø125 - Ø250 D = Pass-through connection, dim. 200 and 250 only. Tellus-Opus -125 / 0 / 0 Fig. 2 Tellus-Opus supply diffuser, dimension Ø

45 Tellus-LØV VAV Tellus-LØV VAV is a circular supply diffuser for open installation with VAV function. It has excellent induction and is suitable for both constant and variable air flow rate. FUNCTION Tellus-LØV VAV has a built-in VAV regulator for demand control of air flow. The damper solution will choke the pressure at high flow rates and maintain a low sound level. This may reduce the need for additional dampers and sound attenuators in a duct system. Tellus-LØV VAV is supplied with Belimo MP-Bus. For communication with Modbus, LON, KNX and BACnet, a Belimo UK 24-Gateway can be utilised. Measurement deviation for the area: 10-20% of nominal: ±25% 20-40% of nominal: <±10% % of nominal: <±4 % In order to sustain the product's measurement accuracy, straight ducting of min. 5 x ØD is recommended. Tellus-LØV VAV is designed as a complete measurement and regulating unit for demand control of air flow in the ventilation system. The measuring station measures the differential pressure via a sensor integrated into the unit. The unit is equipped with a CHV-VAV-MP regulator from Belimo. The regulator specifications are provided in the table below. Tellus-LØV VAV has a removable front plate with LØV perforation. Tellus-LØV VAV is available in both high-profile and low-profile design. Actuator CHV-VAV-MP Operating voltage AC 24 V 50/60 Hz, DC 24 V Power consumption 1.5W Dim. power 2.5 VA QUICK SELECTION, TELLUS-LØV VAV (Open) m 3/ h Dim. 25 db(a) 30 db(a) 35 db(a) (75 Pa) m 3/ h Dim. 25 db(a) 30 db(a) 35 db(a) Table 2 REGULATION RANGE, TELLUS-LØV VAV Tellus-LØV VAV (m 3/ h) ØD. Minimum Maximum Table 3, Regulation range for VAV, air flow rate in m³/h. See calculation diagram for sound power and pressure loss. Table 1, Technical specification, Belimo CHV-VAV-MP regulator MATERIALS AND FINISH Tellus-LØV VAV has a galvanised steel finish. The damper is fitted with a polyester cloth. The spigot has an EPDM rubber gasket. Tellus-LØV VAV are delivered in RAL gloss 30. ORDER CODE, Tellus-LØV VAV 45

46 Tellus-LØV VAV DIMENSIONS AND WEIGHT, TELLUS-LØV VAV Dim. D DA H S Weight [kg] / / / /28/38 11 Table 4 Figure 1. Dimensioned sketch, Tellus-LØV-H VAV Figure 2. Dimensioned sketch, Tellus-LØV-L VAV 46

47 Tellus-Opus VAV VAV Tellus-Opus VAV is a circular supply diffuser with VAV function for open installation. It has excellent induction and is suitable for both constant and variable air flow rate. The diffuser is also available with a passthrough function. FUNCTION Tellus-Opus VAV has a built-in VAV regulator for demand control of air flow. The damper solution will choke the pressure at high flow rates and maintain a low sound level. This may reduce the need for additional dampers and sound attenuators in a duct system. Tellus-Opus VAV is supplied with Belimo MP-Bus. For communication with Modbus, LON, KNX and BACnet, a Belimo UK 24-Gateway can be utilised. Measurement deviation for the area: 10-20% of nominal: ±25% 20-40% of nominal: <±10% % of nominal: <±4 % In order to sustain the product's measurement accuracy, straight ducting of min. 5 x ØD is recommended. Tellus-Opus VAV is designed as a complete measurement and regulating unit for demand control of air flow in the ventilation system. The measuring station measures the differential pressure via a sensor integrated into the unit. The unit is equipped with a CHV-VAV-MP regulator from Belimo. The regulator specifications are provided in the table below. Tellus-Opus VAV has a removable front plate with Opus nozzles. Actuator CHV-VAV-MP Operating voltage AC 24 V 50/60 Hz, DC 24 V Power consumption 1.5W Dim. power 2.5VA Table 1, Technical specification, Belimo VAV regulator QUICK SELECTION, Tellus-Opus VAV (Open) m 3/ h Dim. 25 db(a) 30 db(a) 35 db(a) (75 Pa) m 3/ h Dim. 25 db(a) 30 db(a) 35 db(a) Table 2 REGULATION RANGE, Tellus-Opus VAV Tellus-Opus VAV (m 3/ h) ØD. Minimum Maximum Table 3, Regulation range for VAV, air flow rate in m³/h. See calculation diagram for sound power and pressure loss. MATERIALS AND FINISH Tellus-Opus VAV has a galvanised steel finish. The damper is fitted with a polyester cloth. The spigot has an EPDM rubber gasket. Tellus-Opus VAV are delivered in RAL gloss 30. ORDER CODE, TELLUS-OPUS VAV 47

48 Tellus-Opus VAV DIMENSIONS AND WEIGHT, Tellus-Opus VAV Dim. D DA H S Weight [kg] / / / /29 11 Table 4 Figure 1. Dimensioned sketch, Tellus-Opus VAV 48

49 TLK-B TLK is a rectangular supply diffuser for wall mounting, and is ideal for office premises requiring rear-spigot air connection. With a choice of front panels, most room types can be supplied with a flow pattern adapted to size, width, interior, lighting etc. The TLK comes with a choice of three removable front panels - two with LØV perforation for short and long throw length (K and L), and one with Opus nozzles for variable flow pattern (V). With an adjustable mounting frame between the box and the front, the system can be adapted to the thickness of the wall. The box is equipped with removable damper, measuring outlet and a sound absorber in polyester. Available with rear spigot. The K and L type front panels are made of steel with a RAL gloss 30 finish. Other colours are available on request. The V type diffuser front features Opus nozzles in ABS plastic, is made of steel and comes in a RAL gloss 30 finish. Other colours are also available, but without the adjustable nozzle option. The box is supplied in a galvanised finish, and is internally lined with sound absorber in polyester. EPDM rubber gasket on connection collar. ORDER CODE, TLK box and front Product Connection collar: B = Rear S = Side Dim TLK -B-160 / L / 0 SL = Special finish Front, type: K = LØV perforation, short throw length L = LØV perforation, long throw length V = Opus nozzles, variable flow pattern TLK-B-160 / L / 0 TLK box with rear connection dim. Ø160. Front with LØV perforation, long throw length. Standard scope of use for TLK Distance to opposite wall [m] Short throw length (LØV) Long throw length (LØV) QUICK SELECTION TLK-B-K/L TLK-B-K/L m³/h (30Pa) Dim. 25 db(a) 30 db(a) 35 db(a) QUICK SELECTION TLK-B-V TLK-B-V m³/h (30Pa) Dim. 25 db(a) 30 db(a) 35 db(a) Table 1, show air flow rates at 30 Pa total pressure loss. Sound level is L WA. QUICK SELECTION TLK-S-K/L TLK-S-K/L m³/h (30Pa) Dim. 25 db(a) 30 db(a) 35 db(a) QUICK SELECTION TLK-S-V TLK-S-V m³/h (30Pa) Dim. 25 db(a) 30 db(a) 35 db(a) Table 2, show air flow rates at 30 Pa total pressure loss. Sound level is L WA. Variable throw length (OPUS) Fig. 1: Scope of use TLK 49

50 TLK-S DIMENSIONS AND WEIGHT, TLK TLK Dim D BF HF BK HK DB Table 3 BF HF HK DB D+40 BK ØD Fig. 2, TLK-B 10 BF HK HF 45 A BK Ds ØD D+40 Fig. 3, TLK-S Fig. 4, Front panels 50 3 DS A Weight [kg] Box 5,0 5,9 7,1 8,7 10 Weight [kg] Front 1,0 1,3 1,7 2,1 3,7

51 TUB TUB is a supply diffuser for open installation, and is developed to suit premises with high requirements for comfort and design. The diffuser can either be mounted to the ceiling away from the wall or be installed in the corner between wall and ceiling. TUB features a removable front panel with LØV perforation. The unit is available with two different flow patterns, and in 2, 4 and 6-metre lengths. A ½ curved design is used for open ceiling mounting, and a ¼ curved design is used for installation in corner between wall and ceiling. TUB is equipped with an integrated damper, measuring outlet and sound attenuator. Back panel to accommodate wall mounting can be supplied. DIMENSIONS AND WEIGHT, TUB Dim. Design H B Bs Weight[kg] 160 1/2-curved /2-curved /2-curved /4-curved /4-curved /4-curved Table 3 The diffuser front is in a steel design with a RAL gloss 30 finish. Other colours are available on request. All other elements are made in galvanised steel. The sound attenuator is lined with a sound absorber in polyester, and the connection collar is fitted with an EPDM rubber gasket. QUICK SELECTION TUB [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Table 1. Air flow rates TUB-6m at given sound power levels and open damper. Table applies to both 1/2R and 1/4R execution. TUB [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Table 2. Air flow rates TUB-6m at given sound power levels 30Pa pressure loss. Table applies to both 1/2R and 1/4R execution. H 20 Bs B H 20 Bs B ORDER CODE, TUB TUB /4R -4 / DV / 0 Product SL = Special finish Fig. 1. The figure shows a 1/4R right unit. Dimension: Ø160 - Ø250 Types: 1/2R = ½ curved for ceiling installation 1/4R = ¼ curved for wall/ceiling installation L = Length: 2, 4 or 6 m Flow pattern 1/2R S = Right-angled D = ~ 45 out Flow pattern 1/4R SV = Right-angled out, left SH = Right-angled out, right DV= ~ 45 out, left D = ~ 45 out, right TUB-160-1/4R-4 / DV-0 / 0 TUB dim. Ø160 ¼ curved for ceiling installation, length: 4 m. Flow pattern: ~ 45 out, left. 51

52 TIH The TIH diffuser is ideal for industrial premises as well as department stores, garage facilities and similar. Available in 3 different designs and sizes, and comes with internal diffuser plate as standard. TIH-1 for circular-duct connection (see fig. 1), TIH-2 for flat-duct connection and TIH-3 with circular connection collar. Annular design is available on request. NB! Remember to specify connection diameter ( D2, fig. 2) when ordering TIH-1. DIMENSIONS AND WEIGHT, TIH TIH Weight Dim. A B H D [kg] Table 2: TIH Comes in a galvanised, steel-plated finish. Other materials and colours are available on request. QUICK SELECTION TIH [m³/h] Dim. 30 db(a) 35 db(a) 40 db(a) Table 1: The table provides air flow rates at given sound power levels Fig. 1: TIH ORDER CODE, TIH TIH / 0-0 Product Dimension: Ø315 - Ø500 Type: 1, 2 or 3. As per fig. 1 L = Painted finish SM = Special material Fig. 2: TIH TIH / 0-0 TIH, dim. Ø400, type 2. 52

53 TIR TIR is the ideal solution when high air flow rates are required, and is primarily intended as a freely suspended unit. It can, as an example, be used to supply hot or cold air to the occupied zone in rooms with high ceilings. TIR comes with a perforated face-plate and with fixed slot-height to the diffuser cover which is also the absorption mat. Fitted underneath the face-plate is a string-operated sector shutter where the air flow rate, and thus also the supporting air jet and throw length, are regulated. With a deflector, the slot can be adjusted to provide a vertical air flow (see fig. 4, last page). DIMENSIONS AND WEIGHT, TIR TIR Weight Dim. A B H [kg] Table 4, TIR Supplied in a galvanised, steel-plated finish. Other materials and colours are available on request. QUICK SELECTION, TIR TIR [m³/h] Dim. 30 db(a) 35 db(a) 40 db(a) Table 3: The table provides air flow rates at given sound power levels Fig. 3, TIR ORDER CODE, TIR TIR / LR - 0 / 0-0 Product L = Painted finish Dimension Ø315 SM = Special material LR = Deflector SB = Sector shutter TIR-500/ LR-0 / 0-0 TIR, dim. Ø500, equipped with deflector. 53

54 DKW DKW is a perforated duct diffuser for freely suspended or embedded installation. The system can be adjusted to the length required by combining active parts and blanked-off ducts. With its choice of flow patterns, the DKW can be used for both under- and overheated air and is a high installation-friendly solution. FLOW PATTERNS To accommodate for room geometry and positioning, the following flow patterns are available. Type and dispersion angle must be included in the order code. * = only as 4m diffuser for Ø ** = only as 4m diffuser for Ø500 DKW has a diameter equivalent to standard ductwork dimensions. The unit is delivered with an active length of 2 m or 4 m. Total length required is achieved by using blanked-off ducts. Both the blanked-off ducts and active parts are available in 1m or 2m modules. Parts are joined together by means of connection nipples and a sealed end-cover. The DKW is fitted with a suspension bar at the top. DKW comes in a galvanised steel-plate design with a RAL gloss 30 finish. Other colours and galvanised versions are available on request. DIMENSIONS AND WEIGHT, DKW DKW has a diameter equivalent to standard ductwork dimensions. The modules are available in 1m or 2m lengths. Fig. 1: Flow patterns and types POSITIONING IN ROOM Air velocities in the occupied zone will, in addition to air flow rate and temperature, depend on solid geometry, heat sources and the positioning of these. In order to limit the risk of draft in the occupied zone, the diffuser should have 3 x ØD from the wall, see figur 2. For undercooled air, mounting height to the diffuser s lower part should be at least 2.5 m at Dt=3, and at least 3.5 at Dt=10. Dim. Weight per meter [kg] 160 2, , , , , ,7 Table 1 QUICK SELECTION DKW [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Ø160, 2m Ø160, 4m Ø200, 2m Ø200, 4m Ø250, 2m Ø250, 4m Ø315, 2m Ø315, 4m Ø400, 2m Ø400, 4m Ø500, 2m Ø500, 4m Fig. 2: Spacing for positioning in room ORDER CODE DKW x90 / B S - T - 0 / 0 Product SL = Special finish Dimension: J = Adjustable attachment Ø160 - Ø500 T = Sealed end-cover Active length: 2 or 4 m. S = Connection nipple Active length, split: Length, blanked-off duct: or 2 m B = Blanked-off duct Type as per fig. 1 Pattern as per fig. 1 DKW x90 / B-1500-S-T-0 / 0 DKW, dim. Ø160, 4m length, two 2m units, type 4, pattern: 2x90º. Blanked-off duct, length: 1500, connection nipple and sealed end-cover. Number of connection nipples and sealed end-covers is determined by the total length required. For suspension purposes, each length is delivered with one M6 nut as standard. Table 2: The table shows air flow rate at given sound power levels. 54

55 RFD RFD is a circular swirl diffuser for ceiling mounting. Swirl diffuser with fixed deflection blades. RFD is made of steel and comes in a RAL gloss 30 finish. DIMENSIONS AND WEIGHT, RFD-R-D-K Dim. A B H Weight [kg] , , , , , ,0 Table 2: QUICK SELECTION, RFD-R-D-K RFD [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) ØB ØA 50 H Table 1: The table shows air flow rates at given sound power levels. ORDER CODE, RFD-R-D-K RFD-R-D-K Product Dimension : Ø125 - Ø400 Fig. 1 RFD-R-D-K RFD-R-D-K, dimension Ø160 ORDER CODE, Luna Luna UI = Outlet installed, low profile design RH = Plenum box for fixed ceiling plate I = Insulated Dimension outlet: Ø125 Ø400 Dimension inlet: Ø100 Ø315 Luna Luna plenum box with inlet Ø125 and outlet Ø160 55

56 RFD with Luna plenum box The Luna plenum box is recommended for improved sound attenuation, and works as an adjustment and measurement option. Luna is a rectangular box fitted with a removable damper which provides access to the connecting duct. The damper can be secured in any position required. The Luna plenum box features a damper and measurement device for adjustment. It is insulated with a sound absorber in polyester and is available with one or two dimensional changes between inlet and outlet. Furthermore, the box can be supplied with external condensation insulation. A low-profile design [UI] is also available, and for this design a reduction in capacity of approx. 20% will apply. The distance between diffuser and box can be increased by up to 35 cm without extending the wire and measuring tube. Luna is supplied in a galvanised finish, and with all four internal walls lined with sound absorber in polyester. The connection collar is fitted with an EPDM rubber gasket. DIMENSIONS IONS AND WEIGHT, Luna Dim. D DA B H H1 H2 L L1 L2 Weight Luna [kg] , , , , , , , , , , Table 4 QUICK SELECTION RFD-R-D-K Luna [m³/h] Dim. Dim. 25 db(a) 30 db(a) 35 db(a) Table 3: The table shows air flow rates at given sound power levels and 50 Pa total pressure loss. ORDER CODE, RFD-R-D-K with Luna RFD-R-D-K-L Fig. 2 L L = Luna UI = Outlet installed, low profile design RH = Plenum box for fixed ceiling plate I = Insulated Dimension outlet: Ø125 Ø400 Dimension inlet: Ø100 Ø315 RFD-R-D-K-L RFD-R-D-K swirl diffuser and Luna plenum box with inlet Ø125 and outlet/diffuser dim. Ø

57 Orion-LØV Orion-LØV is a square supply diffuser for installation in modular ceiling systems. The unit offers excellent induction, and is suitable for both constant and variable air flow rates. Orion-LØV features a removable front panel with LØV perforation. Rotational pattern is supplied as standard. The unit is equipped with a TA flange suitable for T-profile ceiling systems, but is also available with alternative flange designs, type: DC, DG, DS and EK (see fig. 2 and under order code). DIMENSIONS AND WEIGHT, Orion-LØV Orion-LØV D Weight walve [kg] , , , , , ,9 Table 2 The front panel, ceiling plate and valve body are in a steel design, and the valve body is equipped with EPDM rubber gasket. Corner connection points are in plastic, and are fitted with holding magnets. All internal and external valve elements are in a RAL gloss 30 finish. Other colours are available on request. QUICK SELECTION Orion-LØV [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Table 1: The table provides air flow rates at given sound power levels. Fig. 1 ORDER CODE, Orion-LØV (Orion-LOEV) A-flange Dampa Clip-In Dg-flange Orion-LØV - TA / 0 Ceiling systems: : TA = A-flange DC = Dampa Clip-In DG = Dg-flange DS = Ds-flange EK 24 = E-flange -T24 EK 15 = E-flange -T15 SL = Special finish Dimension: Ø125 - Ø400 Orion-LOEV-TA-160/0 Orion-LOEV supply diffuser with A flange for T-profile ceiling system, spigot Ø160. DS-flange E-flange BESTILLINGSKODE, ORDER CODE, Luna Luna (Side 2) T24/T15 Luna Fig. 2 UI = Outlet installed, low profile design I = Insulated Dim. outlet: Ø125 - Ø400 Dim. inlet: Ø100 - Ø315 Luna Luna with inlet Ø125 and outlet Ø160 57

58 Orion-LØV with Luna plenum box The Luna plenum box is recommended for improved sound attenuation, and works as an adjustment and measurement unit. Luna is a rectangular box fitted with a removable damper which provides access to the connecting duct. The damper can be secured in any position required. The Luna plenum box features a damper and measuring outlet for commissioning. It is insulated with a sound absorber in polyester and is available with one or two dimensional changes between inlet and outlet. Furthermore, the box can be delivered with external condensation insulation. A low-profile design [UI] is also available, and for this type a reduction in capacity of approx. 20% will apply. The distance between valve and box can be increased by up to 35 cm without extending the wire and measuring tube. Luna is supplied a galvanised finish and with all four internal walls lined with sound absorber in polyester. The spigot is fitted with an EPDM rubber gasket.. QUICK SELECTION Orion-LØV Luna [m³/h] Dim. Dim. 25 db(a) 30 db(a) 35 db(a) Table 3: The table provides air flow rates at given sound power levels and 30 Pa total pressure loss.. ORDER CODE, Orion-LØV (Orion-LOEV) with Luna DIMENSIONS AND WEIGHT, Luna Dim. D DA B H H1 L L1 L2 Weight Luna [kg] , , , , , , , , , , , , , , , ,7 Table 4 Fig. 3 Luna UI = Outlet installed, low profile design I = Insulated Dim. outlet: Ø125 - Ø400 Dim. inlet: Ø100 - Ø315 Luna Luna with inlet Ø125 and outlet Ø160 58

59 Orion-Opus Orion-Opus is a square supply diffuser for installation in modular ceiling systems. The unit offers excellent induction, and is suitable for both constant and variable air flow rates. Orion-Opus features a removable front panel with Opus nozzles, and is available with 4 different nozzle settings: rotational, 1-way, 2-way 180º or 2-way 90º. Please see order code and fig.3. Furthermore, the unit is equipped with a TA flange suitable for T-profile ceiling systems, but is also available with alternative flange designs, type: DC, DG, DS and EK (see fig. 2 and order code). DIMENSIONS AND WEIGHT, Orion-Opus Orion-Opus D Valve weight [kg] , , , , , ,9 Table 2 The front panel, ceiling plate and valve body are in a steel design, and the connection collar is fitted with an EPDM rubber gasket. Opus nozzles at the front and corner connection points are in plastic. Connection points are fitted with holding magnets. All internal and external valve elements are in a RAL gloss 30 finish. Other colours are available on request. QUICK SELECTION Orion-Opus [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Table 1: The table provides air flow rates at given sound power levels. Fig. 1 A-flange A-kant Dampa Clip Clip-In Dg Dg-kant flange Ds Ds-kant flange E flange E-kant T24/T15 ORDER CODE, Orion-Opus Orion-Opus - R - TA / 0 Fig. 2 Nozzle settings, front: R = Rotational 1 = 1-way 2A = 2-way 180º 2B = 2-way 90º See fig. 3 SL = Special finish Dimension: Ø125 - Ø400 For ceiling system: TA = A flange DC = Dampa Clip In DG = Dg flange DS = Ds flange EK24 = E-flange - T24 EK15 = E-flange - T15 Orion-Opus-R-TA-160/0 Orion-Opus supply diffuser with rotational nozzle setting at front. A flange for T-profile ceiling system, spigot Ø160. Rotation pattern 1-way pattern BESTILLINGSKODE, Luna ORDER CODE, Luna (Side 2) Luna Dim. outlet: Ø125 - Ø400 UI = Outlet installed, Dim. inlet: Ø100 - Ø315 low profile design I = Insulated Luna Luna with inlet Ø125 and outlet Ø way pattern 180 dgr. Fig. 3 Nozzle settings, Orion-Opus 2-way pattern 90 dgr. 59

60 Orion-Opus with Luna plenum box 60 The Luna plenum box is recommended for improved sound attenuation, and works as an adjustment and measurement unit. Luna is a rectangular box fitted with a removable damper which provides access to the connecting duct. The damper can be secured in any position required. Luna plenum box features a damper and measuring outlet for commissioning. It is insulated with a sound absorber in polyester and is available with one or two dimensional changes between inlet and outlet. Furthermore, the box can be delivered with external condensation insulation. A low-profile design [UI] is also available, and for this type a reduction in capacity of approx. 20% will apply. The distance between valve and box can be increased by up to 35 cm without extending the wire and measuring tube. Luna is supplied in a galvanised finish, and with all four internal walls lined with sound absorber in polyester. Equipped with EPDM rubber gasket on connection collar. QUICK SELECTION Orion-Opus Luna [m³/h] Dim. Dim. 25 db(a) 30 db(a) 35 db(a) Table 3: The table provides air flow rates at given sound power levels and 30 Pa total pressure loss. ORDER CODE, Orion-Opus with Luna Orion-Opus - R - TA - L / 0 SL = Special finish Nozzle settings, front: R = Rotational 1 = 1-way 2 = 2-way 2A = 2-way 180º 2B = 2-way 90º See fig. 3 For ceiling system: TA = A flange DC = Dampa Clip In DG = Dg flange DS = Ds flange EK 24 = E-flange - T24 EK 15 = E-flange - T15 L L = Luna Dim. outlet: Ø125 - Ø400 UI = Outlet installed, low profile design Dim. inlet: Ø100 - Ø315 I = Insulated Orion-Opus-R-TA-L /0 Orion-Opus supply diffuser with rotational nozzle setting at front, A flange for T-profile ceiling system. Luna plenum box, inlet dim. Ø125 and outlet/valve dim. Ø160. DIMENSIONS AND WEIGHT, Luna Dim. D DA B H H1 L L1 L2 Weight Luna [kg] , , , , , , , , , , , , , , , ,7 Table 4 Fig. 4

61 Orion-PTV Orion-PTV is a square supply diffuser for installation in modular ceiling systems. Orion-PTV is a high-capacity system with excellent induction, and is ideal for high air flow rates. Orion-PTV features a removable front panel with perforated front and sides. The unit is equipped with a TA flange suitable for T-profile ceiling systems, but is also available with alternative flange designs, type: DC, DG, DS and EK (see fig. 2 and order code). DIMENSIONS AND WEIGHT, Orion-PTV Orion-PTV D Vekt ventil [kg] , , , , , ,9 Tabell 2 The front panel, ceiling plate and valve body are in a steel design, and the connection collar is fitted with an EPDM rubber gasket. Corner connection points are in plastic, and are fitted with holding magnets. All internal and external valve elements are in a RAL gloss 30 finish. Other colours are available on request. QUICK SELECTION Orion-PTV [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Table 1: Air flow rate at given sound power levels Fig. 1 ORDER CODE, ORION-PTV A-flange A-kant Dampa Clip-In Dg-flange Dg-kant Orion-PTV - TA / 0 For ceiling system: TA = A-flange DC = Dampa clip in DG = Dg flanget DS = Ds flange EK24 = E-flange-T24 EK15 = E-flange-T15 SL = Special finish Dimension: Ø125 - Ø400 Ds-flange Ds-kant E-flange E-kant Orion-PTV-TA-160/0 Orion-PTV supply diffuser with A flange for T-profile ceiling system, spigot Ø160. ORDER CODE, Luna Luna Fig. 2 T24/T15 UI = Outlet installed, low profile design I = Insulated Dim. outlet: Ø125 - Ø400 Dim. inlet: Ø100 - Ø315 Luna Luna with inlet Ø125 and outlet Ø

62 Orion-PTV with Luna plenum box The Luna plenum box is recommended for improved sound attenuation, and works as an adjustment and measurement unit. Luna is a rectangular box fitted with a removable damper which provides access to the connecting duct. The damper can be secured in any position required. Luna plenum box features a damper and measuring outlet for commissioning, is lined with a sound absorber in polyester and is available with one or two dimensional changes between inlet and outlet. Furthermore, the box can be delivered with external condensation insulation. A lowprofile design [UI] is also available, and for this type a reduction in capacity of approx. 20% will apply. The distance between valve and box can be increased by up to 35 cm without extending the wire and measuring tube. The front panel, ceiling plate and valve body are in a steel design, and the connection collar is fitted with an EPDM rubber gasket. Corner connection points are in plastic, and are fitted with holding magnets. All internal and external valve elements are in a RAL gloss 30 finish. Other colours are available on request. QUICK SELECTION Orion-PTV Luna [m³/h] Dim. Dim. 25 db(a) 30 db(a) 35 db(a) Table 3: Air flow rates at given sound power levels and 30 Pa total pressure loss. DIMENSIONS AND WEIGHT, Luna Dim. D DA B H H1 L L1 L2 Weight Luna [kg] , , , , , , , , , , , , , , , ,7 Table 4 Fig. 3 ORDER CODE, Orion-PTV with Luna Orion-PTV - TA - L / 0 Product For ceiling system: TA = A-flange DC = Dampa clip-in DG = Dg-flange DS = Ds-flange EK24 = E-flange-T24 EK15 = E-flange-T15 L = Luna UI = Outlet installed, low profile design I = Insulated SL = Special finish L Dim. outlet: Ø125 - Ø400 Dim. inlet: Ø100 - Ø Orion-PTV-TA-L /0 Orion-PTV supply diffuser with A flange for T- profile ceiling system, Luna plenum box inlet dim. Ø125 and outlet/valve dim. Ø160. 3

63 JBV These air diffusers are designed for comfort ventilation in all types of homes where balanced ventilation is installed, e.g. new builds or rehabilitated blocks of flats. They are designed for standard wall thicknesses with steel joists and a single sheet of plasterboard on both sides. The rectangular JBV air diffuser consists of two parts: the mounting frame, with a spigot for the supply air duct, and a removable front face. No tools are required to install the diffuser face, and it can be easily removed for cleaning, etc. The diffuser face has separate grooves for control wires and measuring tubes. DIMENSIONS AND WEIGHT, JBV Dim D H Weight [kg] , , ,9 Table 1 MATERIALS AND FINISH The diffuser's parts are made of galvanised sheet steel. The surface is painted standard white RAL gloss 30. ORDER CODE, JBV JBV- 100 / 0 Product Dimension: 100,125 or 160 SL = Special paint Figure 1, JBV JBV-100/0 JBV diffuser dimension Ø100, standard paint RAL gloss 30. ORDER CODE, BVK BVK - R Produkt: R = Straight design V= Angle design Dimension Dimensjon intake innløp - utløp: outflow: , eller or BVK-R-100 BVK box with Ø100 intake and Ø100 outflow. 63

64 JBV with BVK box A BVK plenum box is recommended because it provides better sound attenuation and control and measuring options. The BVK is a rectangular box with detachable sound insulation and a damper which provides access to the connecting duct. The damper can be locked in any position required. The BVK comes in two designs, straight and angled. The sound insulation effectively dampens sound and releases no material fibres to the surroundings. The insulation can be removed for cleaning. The plenum box features a wire operated damper and measuring outlet for adjustment. DIMENSIONS AND WEIGHT, BVK Dim. D DA B H C Weight [kg] , , ,3 Table 4 MATERIALS AND FINISH The BVK is supplied with a galvanised finish and polyester sound insulation. The spigot has a rubber EPDM seal. QUICK PICK, JBV with BVK-R box JBV BVK-R [m³/h] Dim Dim 25dB 30dB 35dB Table 2: the table shows the air flow rate at the stated sound power level and 30Pa total pressure. Figure 2, BVK-R QUICK PICK, JBV with BVK-V box JBV BVK-V [m³/h] Dim Dim 25dB 30dB 35dB Table 3: the table shows the air flow rate at the stated sound power level and 30Pa total pressure. Figure 3, BVK-V ORDER CODE, JBV with BVK JBV - K / 0 SL= Special paint K - R Produkt: K = BVK kammer R = Straight design V = Angle design Dimensjon Dimension innløp intake - utløp: outflow , or eller JBV-K-R-100/0 JBV diffuser with accompanying BVK box, box with intake dimension Ø100 and outflow/diffuser dimension Ø100. Diffuser painted with standard RAL gloss

65 Orion-LØV with Sirius Orion-LØV with Sirius is a diffuser unit with VAV function, and is used as volume flow controller and diffuser in ventilation systems to enable air flow rates to be set as per requirements. Orion-LØV offers excellent induction, and is ideal for variable air flow rates. FUNCTION Orion-LØV with Sirius has a built-in VAV controller for adjustment of air flow rates according to requirements. The damper solution will choke the pressure at high flow rates and will maintain a low sound level. This may reduce the need for additional dampers and sound attenuators in a duct system. Orion-LØV with Sirius is delivered with Belimo MP-bus, LON, Modbus or Belimo KNX for direct BUS communication to SD systems. Deviation for working range 10-20% of V nom :±25% 20-40%: of V nom <±10% %: of V nom <±4% If T-pipes are used, a spacing of at least 5 x ØD is recommended in order to maintain the measurement accuracy. ORDER CODE, diffuser - Orion-LØV Sirius (Connection 4 and 6) Orion-LØV-Sirius supply diffuser with A flange for T-profile ceiling system, Orion-LØV with Sirius is a complete measuring and control unit where the air flow rates in ventilation systems can be set as required. At the measuring station, the differential pressure is measured by using measuring rods integrated in the unit. Sirius is equipped with LHV.D3 VAV controller from Belimo. Controller specifications are provided in the table below. Full technical documentation can be downloaded from Orion-LØV features a removable front panel with LØV perforation, and is suitable for a range of ceiling systems. Actuator LHV-D3-MP/MOD/LON Operating voltage AC 24 V 50/60 Hz, DC 24 V Power drain 2,5W Dim. effect 4.5VA (max.8 ms) Table 1: Technical specifications, Belimo VAV controller Sirius comes in a galvanised steel design. The measurement unit is in aluminium, and hoses and nipples are in plastic. The damper is equipped with polyester material, and the connection collar is fitted with EPDM rubber gasket. ORDER CODE, Sirius Dim: Sirius Connection: 0 = MP-Bus 1 = MP-Bus with VIP-X plug 2 = LON-Bus 3 = MOD-Bus 4 = MP-Bus with EasyLink plug 5 = Stand alone with trafo for CO2 and temperature 6 = Stand alone with trafo for PIR/potential free switch 7 = Belimo KNX 8 = MOD-Bus for X-AIRCONTROL Sirius Sirius with Ø125 inlet and Ø200 outlet, ready for EasyLink with MP-Bus controller. 65

66 Orion-LØV with Sirius QUICK SELECTION, Orion-LØV with Sirius [open] m³/h Sirius dim. 25dB(A) 30dB(A) 35dB(A) (75Pa) m³/h Sirius dim. 25dB(A) 30dB(A) 35dB(A) DIMENSIONS AND WEIGHT, Orion-LØV with Sirius Dim. D DA B H L L1 Weight Weight Sirius Sirius with valvel [kg] [kg] ,5 14, Table 4 Table 2: Quick selection, Orion-LØV with Sirius Sirius (m³/h) ØD. Minimum Maximum Table 3: Adjustment range for VAV controller, air flow rate in m 3 /h. See calculation diagram for sound power level and pressure drop. ORDER CODE, Orion-LØV with Sirius Fig. 1: Dimensions, Orion-LØV with Sirius Orion-LØV-Sirius TA B 200 S 0 SL = Special finish Modular ceiling system: TA=A-flange DC=Dampa Clip-In SK DG=Dg-flange Connection: DS=Ds-flange SK=Sirius 0 = MP-Bus EK 24=E-flange-T24 1 = MP-Bus with 4 pole plug EK 15=E-flange-T15 Inlet-outlet 2 = LON-Bus = MOD-Bus B=Motion sensor = MP-Bus with EasyLink plug (Connection 4 and 6) 5 = Stand alone with trafo for CO2 and temperature Dim: Ø200,Ø250,Ø315,Ø = Stand alone with trafo for PIR/potential free switch 7 = Belimo KNX 8 = MOD-Bus for X-AIRCONTROL Orion-LØV-Sirius-TA-B-200-SK /0 Orion-LØV-Sirius supply diffuser with A flange for T-profile, motion-sensor at diffuser front, spigot Ø200, Sirius box Ø125 inlet and Ø200 outlet, ready for EasyLink with MP-Bus controller. 66

67 Orion-Opus with Sirius Orion-Opus with Sirius is a diffuser unit with VAV function, and is used as volume flow controller and diffuser in ventilation systems to enable air flow rates to be set as per requirements. Orion-Opus offers excellent induction, and is ideal for variable air flow rates. FUNCTION Orion-Opus with Sirius has a built-in VAV controller for adjustment of air flow rate. The damper solution will choke the pressure at high flow rates and will maintain a low sound level. This may reduce the need for additional dampers and sound attenuators in a duct system. Orion-Opus with Sirius is delivered with Belimo MP-Bus, LON, Modbus or belimo KNX for direct BUS communication to SD systems. Deviation for working range 10-20% of V nom :±25% 20-40%: of V nom <±10% %: of V nom <±4% If T-pipes are used, a spacing of at least 5 x ØD is recommended in order to maintain the measurement accuracy. Orion-Opus with Sirius is a complete measuring and control unit where the air flow rates in ventilation systems can be set as required. At the measuring station, the differential pressure is measured by using measuring rods integrated in the unit. Sirius is equipped with LHV-D3 VAV controller from Belimo. Controller specifications are provided in the table below. Full technical documentation can be downloaded from Orion-Opus with Sirius features a removable front panel, and is available with 4 different nozzle settings: rotational, 1-way, 2-way 180 or 2-way 90. It is suitable for a range of ceiling systems. Actuator LHV-D3-MP/MOD/LON Operating voltage AC 24 V 50/60 Hz, DC 24 V Power drain 2,5W Dim. effect 4.5VA (max.8 ms) Table 1: Technical specifications, Belimo VAV controller Sirius comes in a galvanised steel design. The measurement unit is in aluminium, and hoses and nipples are in plastic. The damper is equipped with polyester material, and the connection collar is fitted with EPDM rubber gasket ORDER CODE, diffuser - Orion-Opus Sirius (Connection 4 and 6) ORDER CODE, Sirius Dim: Sirius Connection: 0 = MP-Bus 1 = MP-Bus with VIP-X plug 2 = LON-Bus 3 = MOD-Bus 4 = MP-Bus with EasyLink plug 5 = Stand alone with trafo for CO2 and temperature 6 = Stand alone with trafo for PIR/potential free switch 7 = Belimo KNX 8 = Mod-Bus for X-AIRCONTROL Sirius Sirius with Ø125 inlet and Ø200 outlet, ready for EasyLink with MP-Bus controller. 67

68 Orion-Opus with Sirius QUICK SELECTION, Orion-OPUS with Sirius [Open] m³/h Sirius dim. 25dB(A) 30dB(A) 35dB(A) (75Pa) m³/h Sirius dim. 25dB(A) 30dB(A) 35dB(A) Table 2: Quick selection, Orion-Opus with Sirius DIMENSIONS AND WEIGHT, Orion-Opus with Sirius Dim. D DA B H L L1 Weight Weight Sirius Sirius with valve [kg] [kg] ,5 14, Table 4 Sirius (m³/h) ØD. Minimum Maximum Table 3: Adjustment range for VAV controller, air flow rate in m3/h. See calculation diagram for sound power level and pressure drop. ORDER CODE, Orion-Opus with Sirius Fig. 1: Dimensions, Orion-Opus with Sirius Orion-Opus-Sirius R TA B 200 SK 0 SL=Special finish 68 Nozzle settings front: R = Rotational 1 = 1-way 2A = 2-way 180 2B = 2-way 90 Dim: Ø200 Ø250 Ø315 Ø400 Modular ceiling system: SK TA=A-flange DC=Dampa Clip-In Connection: DG=Dg-flange 0 = MP-Bus SK=Sirius DS=Ds-flange 1 = MP-Bus with VIP-X plug EK 24=E-flange-T24 Inlet - outlet 2 = LON-Bus EK 15=E-flange-T = MOD-Bus B=Motion-sensor (Connection 4 and 6) = MP-Bus with EasyLink plug = Stand alone with trafo for CO2 and temperature 6 = Stand alone with trafo for PIR/ potential free switch 7 = Belimo KNX Orion-Opus-Sirius-R-TA-B-200-SK /0 8 = MOD-Bus for X-AIRCONTROL Orion-Opus-Sirius supply diffuser with rotational nozzle setting at front, A flange for T-profile ceiling system, motion-sensor at front, spigot Ø200, Sirius box inlet Ø125 and outlet Ø200, Ready for EasyLink with MP-Bus controller. 3

69 Orion-PTV with Sirius Orion-PTV with Sirius is a diffuser unit with VAV function, and is used as volume flow controller and diffuser in ventilation systems to enable air flow rates to be set as per requirements. Orion-PTV is a highcapacity system with excellent induction, and is ideal for high air flow rates. FUNCTION Orion-PTV with Sirius has a built-in VAV controller for adjustment of air flow rates according to requirements. The damper solution will choke the pressure at high flow rates and will maintain a low sound level. This may reduce the need for additional dampers and sound attenuators in a duct system. Orion-PTV with Sirius is delivered with Belimo MP-Bus, LON, Modbus or Belimo KNX for direct BUS communocation to SD systems. Deviation for working range 10-20% of V nom :±25% 20-40%: of V nom <±10% %: of V nom <±4% If T-pipes are used, a spacing of at least 5 x ØD is recommended in order to maintain the measurement accuracy. Orion-PTV with Sirius is a complete measuring and control unit where the air flow rates in ventilation systems can be set as required. At the measuring station, the differential pressure is measured by using measuring rods integrated in the unit. Sirius is equipped with LHV-D3 VAV controller from Belimo. Controller specifications are provided in the table below. Full technical documentation can be downloaded from Orion-PTV features a removable front panel with perforation at the front and sides, and is suitable for a range of ceiling systems. Actuator Operating voltage Power drain 2,5W Dim. effect LHV-D3-MP/MOD/LON AC 24 V 50/60 Hz, DC 24 V 4.5VA (max.8 ms) Table 1: Technical specifications, Belimo VAV controller Sirius comes in a galvanised steel design. The measurement unit is in aluminium, and hoses and nipples are in plastic. The damper is equipped with polyester material, and the connection collar is fitted with EPDM rubber gasket. ORDER CODE, diffuser - Orion-PTV Sirius ORDER CODE, Sirius Dim: (Connection 4 and 6) Sirius Connection: 0 = MP-Bus 1 = MP-Bus with VIP-X plug 2 = LON-Bus 3 = MOD-Bus 4 = MP-Bus with EasyLink plug 5 = Stand alone with trafo for room controller 6 = Stand alone with trafo for PIR/potential free switch 7 = Belimo KNX 8 = MOD-Bus for X-AIRCONTROL Sirius Sirius with inlet Ø125 and outlet Ø200, ready for EasyLink with MP-Bus controller. 69

70 Orion-PTV with Sirius QUICK SELECTION, Orion-PTV with Sirius [Open] m³/h Sirius dim. 25dB(A) 30dB(A) 35dB(A) (75Pa) m³/h Sirius dim. 25dB(A) 30dB(A) 35dB(A) DIMENSIONS AND WEIGHT, Orion-PTV with Sirius Dim. D DA B H L L1 Weight Weight Sirius Sirius with valve [kg] [kg] ,5 14, Table 4 Table 2: Quick selection, Orion-PTV with Sirius Sirius (m³/h) ØD. Minimum Maksimum Table 3: Adjustment range for VAV controller, air flow rate in m 3 /h. See calculation diagram for sound power level and pressure drop. ORDER CODE, Orion-PTV with Sirius Fig. 1:Dimensions, Orion-PTV with Sirius Orion-PTV-Sirius TA B 200 S 0 Modular ceiling system: TA=A-flange DC=Dampa Clip-In DG=Dg-flange DS=Ds-flange EK 24=E-flange-T24 EK 15=E-flange-T15 B=Motion-sensor (Connection 4 and 6) Dim: Ø200,Ø250,Ø315,Ø400 SL = Special finish SK Connection: 0 = MP-Bus SK=Sirius 1 = MP-Bus with VIP-X plug Inlet-outlet 2 = LON-Bus = MOD-Bus = MP-Bus with EasyLink plug = Stand alone with trafo for room controller = Stand alone with trafo for PIR/potential free switch 7 = Belimo KNX 8 = MOD-Bus for X-AIRCONTROL Orion-PTV-Sirius-TA-B-200-SK /0 Orion-PTV-Sirius supply diffuser with A flange for T-profile, motion sensor at diffuser front, spigot Ø200, Sirius box inlet Ø125 and outlet Ø200, ready for EasyLink with MP-Bus controller. 70 3

71 Siv-inn 1 The Siv-inn 1 diffuser units are designed for wall mounting, and are intended solely for displacement ventilation. For floor mounting, the unit is turned over and a decorative cover fitted to the top. Siv-inn 1 comprises a base, diffuser unit, main cover with splice connector and telescopic cover on top. The front is perforated with a design-protected clover pattern. The standard design covers ceiling heights of between 2.3 and 2.9 m (incl. 75 mm base unit). All parts are in a steel design. The unit comes in a RAL gloss 30 finish. DIMENSIONS AND WEIGHT, Siv-inn 1 Dim. A B C1 C2 D E H1 Weight [kg] , , Table 2, Siv-inn 1 QUICK SELECTION Siv-inn 1 [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Table 1: The table shows air flow rates at given sound power levels. Siv-inn 1 1/4R ORDER CODE, Siv-inn 1 Siv-inn 1-1/2R -200 / 0 -S / 0 Produc t SL = Special finish 1/4R =1/4curved SM=Special material or 1/2R = 1/2 curved reinforced front: 1.25 mm Dimension: Ø100 -Ø400 SN = SSP connection nipple T = Telescopic cover L = LSM for commissioning* S=Base P = Decorative cover for floor mounting Siv-inn 1-1/2R-200 / 0-S / 0 Siv-inn 1-½ curved, dimension Ø200 and suitable base * = not applicable to dim. Ø400 Siv-inn 1 1/2R Fig. 1, Siv-inn 1 71

72 Siv-inn 2000 In principle, Siv-inn 2000 is a complete Siv-inn 1 unit, i.e. with damper, measuring outlet and sound attenuator. Siv-inn 2000 comprises a complete diffuser unit with a telescopic cover on top. Base is supplied as accessory. Front perforation is a design-protected clover pattern. The standard design covers ceiling heights of between 2.3 and 2.9 m (incl. 75 mm base unit). DIMENSIONS AND WEIGHT, Siv-inn 2000 Dim. A B C1 C2 D E Weight [kg] , , ,0 Table 4, Siv-inn 2000 All parts are in a steel design. The unit comes in a RAL gloss 30 finish. QUICK SELECTION Siv-inn 2000 [m³/h] Dim. 25 db (A) 30 db (A) 35 db (A) Table 3: The table shows air flow rates at given sound power levels. Siv-inn /4R ORDER CODE, Siv-inn 2000 Siv-inn /4R / S / 0-0 Product 1/4R = 1/4 curved 1/2R = 1/2 curved Dimensjon: Ø125 - Ø250 SL = Special finish SM = Special material or reinforced front: 1.25 mm S = Base Siv-inn /4R-160 / S / 0-0 Siv-inn ¼ curved, dimension Ø160 and suitable base Siv-inn /2R Fig. 2, Siv-inn

73 Siv-inn Inlaid The 300x600, 600x300, 400x400, 600x600 and 600x900 product range comprises air supply units for displacement ventilation, and is designed for embedded installation in wall. Siv-inn Inlaid features a duct, box and front grille. Duct height can be adjusted as stated in table 2. The front grill is available in 5 dimension options, and is easily assembled with the screws supplied. DIMENSIONS AND WEIGHT, Siv-inn Inlaid Dim. B H C D BK HK E F L weight* [kg] Table 2: Siv-inn Inlaid (*weight with duct) Siv-inn Inlaid is made of solid steel plate. The front panel is fitted with a gasket and comes in a RAL gloss 30 finish as standard, while the box and duct are in a galvanised steel-plate finish. Reinforced front panel is available on request. QUICK SELECTION Siv-inn Inlaid [m³/h] Type 25 db(a) 30 db(a) 35 db(a) Table 1: The table shows air flow rates at given sound power levels. Type 1 = Dim. 300x600, 400x400 og 600x300 Type 2 = Dim. 600x600 Type 3 = Dim. 600x900 Fig. 1: Siv-inn Inlaid ORDER CODE, Siv-inn Inlaid Siv-innInlaid / AL - Ø / 0-0 Product SL = Special finish, Front Box and front grille, dim.: SM = Spesial material or Width: 300, 400 or 600 reinforced front Height: 300, 400, 600 or 900 (standard dimensions, see table 2) S = SSP L = LSM AL = Moulding Connecting duct, dim.: Ø125 for: , and Ø160 for: Ø200 for: Siv-Inn Inlaid / AL-Ø / 0-0 Siv-inn Inlaid, box and front dimensions: 300 x 600. Supplied with moulding and connecting duct Ø

74 Siv-inn School Siv-inn School is designed for classrooms and lecture halls, but can also be used in other areas. What makes this solution unique is its compliance with the requirements for efficient air replacement, low velocity in the occupied zone and easy-clean design. The unit is particularly well-suited for renovation work as it provides a certain clearance between diffuser and wall. Conflict with cornices, cables, etc. is thus avoided. The unit features a sound attenuator, measuring station and damper. Its front, perforated with our design protected-clover pattern, provides excellent induction and even air distribution to the room. The unit comes in a galvanized steel-plate design, with a RAL gloss 30 finish as standard. Other materials/colours are available on request. DIMENSIONS AND WEIGHT, Siv-inn School Dim. d D H tot Weight [kg] , , , , ,5 Table 2 Adjustable: mm. QUICK SELECTION Siv-inn School [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) Table 1. The table shows air flow rates at given sound power levels. Fig.1 ORDER CODE, Siv-inn School 74

75 Siv-inn 2 Siv-inn 2 is designed for displacement ventilation in industrial buildings. Comes with a top-entry spigot, and is available in a rectangular as well as a 1/4, 1/2 and 1/1 curved design. All parts are in a steel design. The unit is delivered in a galvanized steel finish as standard, but is also available in special material and/or in an painted finish. QUICK SELECTION, Siv-inn 2. 1/4R, 1/2R og 1/1R H = 1500 and H = 2000 Siv-inn 2 [m³/h] Dim. 35 db(a) 40 db(a) 45 db(a) Table 1: The table shows air flow rates at given sound power levels. DIMENSIONS AND WEIGHT, Siv-inn 2 Dim. A B C D E Weight [kg] Weight [kg] *1/2R *1/1R / / / / / / / / / / 70 Table 3: Siv-inn 2. 1/2R and 1/1R (*for H=1500 and H=2000 respectively). Dim. A B D *Weight [kg] / / / / / 132 Table 4: Siv-inn 2. 1/4R (*for H=1500 and H=2000 respectively). Type B C E H D Weight [kg] Table 5: Siv-inn 2. Rectangular QUICK SELECTION, Siv-inn 2. Rectangular Siv-inn 2 [m³/h] Type 35 db(a) 40 db(a) 45 db(a) Table 2: The table shows air flow rates at given sound power levels. ORDER CODE, Siv-inn 2. 1/4R, 1/2R and 1/1R Siv-inn 2-1/2R / 0-0 Product 1/4R = 1/4 curved 1/2R = 1/2 curved 1/1R = 1/1 curved SL = Special finish SM = Special material Height: 1500 or 2000 Dimension: Ø315 - Ø800 Siv-inn 2-1/2R / 0-0 Siv-inn 2-1/2 curved, dimension Ø500 and height 2000 ORDER CODE, Siv-inn 2. Rectangular Siv-inn / 0-0 Product Type: 128, 206, 2010 or 2012 SL = Special finish SM = Special material Siv-inn / 0-0 Siv-Inn 2 type

76 A Siv-inn 2 B OD A C H=høyde=1500mm H = height = mm eller or 2000mm mm Fig. 1, Siv-inn 2. 1/2R OE OD H = height = 1500 mm or 2000 mm H=høyde=1500mm eller 2000mm Fig. 2, Siv-inn 2. 1/1R B OD H H=høyde=1500mm = height = mm eller or 2000mm mm Fig. 3, Siv-inn 2. 1/4R OD C E B H = height H=høyde Fig. 4, Siv-inn 2. Rectangular. 76

77 Siv-inn T/V Siv-inn T/V is a supply diffuser for areas requiring high air flow rates such as commercial kitchens or laboratories. Suitable for open as well as embedded installation (se fig. 2). The product is available in 6 different sizes, with circular end-spigot as standard. External dimensions are designed to fit T-profile ceiling systems with module 600. Alternative connection solutions and positioning are available on request. Siv-inn T/V can also be supplied with perforated sides. The front panel is reinforced and can be removed by unfastening the screws. WEIGHT AND DIMENSIONS, Siv-inn T/V Type A B C D [kg] , , , , , ,0 Table 2 Siv-inn T/V comes in a galvanised steel-plate design. Sides and front are in a white RAL gloss 30 finish. QUICK SELECTION Siv-inn T/V [m³/h] Type 25 db(a) 30 db(a) 35 db(a) Table 1: The table shows air flow rates at given sound power levels. Fig. 1 ORDER CODE, Siv-inn T/V Siv-inn T/V / Product Type: 0312, 0612, 0618, 1212, 1218 or 1224 SL = Special finish SM = Special material P = Perforation long side(s) A = Alternative spigot positioning Siv-inn T/V-0612 / Siv-inn T/V, type: 0612 with spigot Ø250. Fig. 2 77

78 Siv-inn PP and PK The Siv-inn panel is a customised product offering every solution imaginable in terms of tailored displacement units, and is available as a made-to measure solution as well as with prefabricated plenum boxes suitable for both wall and ceiling mounting. Grilles measuring over 2 m 2 are split. DIMENSIONS AND WEIGHT, SIV-INN PP/PK Weight: approx. 15 kg/m 2. Recomended groove: B+5 and H+5. B+50 Siv-inn PP and PK are available in two standard designs with width/ height measurements to the nearest millimetre. Featuring a flush flange, type PP is an ideal slot-in solution. Type PK is equipped with a bracket flange and is installed as a protruding unit. Siv-inn PK comes with screw holes fitted with gaskets and spacers, and the screws are in a white enamel finish. The front is perforated (15 %) with our clover pattern. H+50 MAX 400 mm H-2 Both types are equipped with a permanent galvanized diffuser plate. The front comes in a RAL gloss 30 finish as standard. QUICK SELECTION O 6 B-2 [m³/h] Siv-inn PP/PK 25 db(a) 30 db(a) 35 db(a) Table 1: The table shows air flow rates at given sound power levels (per m2 of active area). ORDER CODE, SIV-INN PP/PK PK B-2 B-2 Product Type: PP = Flush flange PK = Bracet flange Width: (mm.) Siv-inn - PP / 0-0 SL = Special finish SM = Special material Hight: (mm.) PP 2 Fig. 1: Siv-inn PP and PK Siv-Inn-PP / 0-0 Siv-inn front with flush flange, width: 500 mm and height: 800 mm. ORDER CODE, Siv-inn PP/PK Box Fig. 2: Spigot entry pos. 2 or pos. 3 requires a minimum C-dimension of: ød Option 4, loose spigot: optional mounting location. Installer creates mounting hole for spigot 78

79 Siv-inn Aula Siv-inn Aula 100 and 125 are primarily intended to meet seating area requirements as shown in fig. 1A. Siv-inn Aula 400, 500 and 600 are intended for low risers as shown in fig. 1B. Siv-inn Aula 2000 is also intended for low risers, but offers continuous-length mounting as shown in fig. 1C. ORDER CODE, Siv-inn-Aula 100 og 125, 0-0 Fig. 1 ORDER CODE, Siv-inn-Aula 400, 500 og 600 SM = Aula 100 and 125 are available in a circular design with Ø100 and Ø125 connection collar. Sealing gasket is fitted as standard. Aula 400, 500 and 600 come in a rectangular design and feature a separate distribution box. The front grille is equipped with a gasket underneath and at both ends, and is perforated with a clover pattern. In addition, the upper edge has been perforated to limit the near-field. Aula 2000 has a rectangular design and is equipped with a rear distribution box dim. 400, 500 or 600. Screws in an enamel finish are standard. Aula 2000 is available as standard lengths of 2000 mm, with splice connectors and end pieces supplied loose. Adjustment lengths are available on request. ORDER CODE, Siv-inn-Aula 2000 The products are made of galvanised steel plates, and come in a RAL gloss 30 finish as standard. Other colours and materials are available on request. QUICK SELECTION Siv-inn Aula [m³/h] Dim. 25 db(a) 30 db(a) 35 db(a) 100/ Table 1: The table shows air flow rates at given sound power levels. 79

80 Siv-inn Aula DIMENSIONS AND WEIGHT, Siv-inn Aula Siv-inn Aula 2000, weight 1.6 kg per metre. Dim. A B Weight [kg] , , ,0 Table 2 Fig. 2 80

81 DRS/DRS-T DRS Ø100 Ø630 is a manual commissioning damper, at dim actuator type CM can be mounted. DRS-M Ø400 Ø 630 is an actuator-controlled commissioning damper. DRS and DRS-M satisfy the EN 1751 requirements for air permeability class 0 and C. DRS-T Ø100 Ø 630 is a manual commissioning and shut-off damper. DRS-T-M DRS-T-M Ø100 Ø 630 is an actuator-controlled commissioning and shut-off damper. DRS-T and DRS-T-M satisfy the EN 1751 requirements for air permeability class 4 and C. The damper s operating temperature is max. 100 C. DIMENSIONS AND WEIGHT Dim. D L B1 Weight [kg] , , , , , ,0 Table1: DRS dim DRS and DRS-T are supplied with graduated scale and lockable commissioning solution. DRS-M and DRS-T-M are equipped with actuator bracket, and the dampers are available with actuator mounted. On the DRS Ø100 Ø315 (fig. 1), provisions have been made for subsequent installation of Belimo CM actuators. DRS Ø100 Ø315 has galvanised steel casing, bracket and scale, whereas the damper, support and commissioning solution come in a plastic design. DRS Ø400 Ø630 features a casing, damper, shaft, bracket and scale in galvanised steel. Support and spacer are in a plastic design. DRS-M Ø400 Ø630 has galvanised steel casing, damper, shaft and actuator bracket, whereas the support come in a plastic design. DRS-T has galvanised steel casing, damper, bracket and scale. The damper blade is fitted with rubber gasket, and the supports are in a plastic design. DRS-T-M has galvanised steel casing, damper, bracket and shaft. The damper blade is fitted with rubber gasket, and the supports are in a plastic design. All damper types are equipped with EPDM rubber gasket. Fig. 1, DRS dim Dim. D L B2 C Weight excl. actuator [kg] , , , , , , , , ,2 Table 2, DRS / DRS-M and DRS-T / DRS-T-M ORDER CODE, DRS DRS / T - M - P / 0 Product L = Enamel finish Dimension Ø100 Ø630 T = Sealed design M = Actuator bracket fitted P = Equipped with actuator DRS-160 / T-M-P/ 0-0 DRS dim. Ø160 sealed design, equipped with actuator bracket and actuator. (Actuator can be ordered separately: see table 3). P.S. If you choose another type of actuator than CM, be aware of that actuator brackets have different constructions depending on actuator type, we recommend: damper and actuator mounted together at factory. Alternatively, specify type of actuator which will be used afterwards. Fig. 2, DRS / DRS-M and DRS-T / DRS-T-M (DRS-M and DRS-T-M are equipped with 8x 8 shaft) (H-dimensions, see table 3) 81

82 DRS/DRS-T ACCESSORIES DAMPER ACTUATOR AND FUNCTION The dampers in table 3 are ready for mounting of Belimo brands. Damper Dim. Actuator Function Torque H-diml weight type [Nm] [mm] [kg] DRS CM24-F-R On/Off ,2 DRS CM230-F-R On/Off ,2 DRS CM24-SR-FR.2 Modulating ,2 DRS-M NM24A/NM230A On/Off ,8 DRS-M NM24A-SR/NM230A-SR Modulating ,8 DRS-M NM24A-MP MP-Bus ,7 DRS-M NM24A-LON LON ,8 DRS-M SF24A/SF230A On/Off spring return ,7 DRS-M SF24A-SR Modulating spring return ,7 DRS-M SF24A-MP MP-Bus spring return ,7 DRS-M SF24A-LON LON spring return ,7 DRS-T-M LM24A-F/LM230A-F On/Off ,5 DRS-T-M LM24A-SR-F/LM230A-SR-F Modulating ,5 / 0,7 DRS-T-M LM24A-MP-F MP-Bus ,5 DRS-T-M LM24A-LON-F LON ,6 DRS-T-M LF24/LF230 On/Off spring return ,4 / 1,6 DRS-T-M LF24-SR Modulating spring return ,4 DRS-T-M LF24-MFT2 MP-Bus spring return ,4 DRS-T-M SM24A/SM230A On/Off ,0 / 1,1 DRS-T-M SM24A-SR/SM230A-SR Modulating ,1 / 1,2 DRS-T-M SM24A-MP MP-Bus ,9 DRS-T-M SM24A-LON LON DRS-T-M SF24A/SF230A On/Off spring return ,7 DRS-T-M SF24A-SR Modulating spring return ,7 DRS-T-M SF 24A-MP MP-Bus spring return ,7 DRS-T-M SF24A-LON LON spring return ,7 Table 3. (Alternative type damper and actuator for DRS , is DRS-T-M ) 82

83 EPS EPS is used for commissioning and completion of ventilation systems without damper EPS is supplied with graduated scale and lockable commissioning solution. The EPS casing, damper and graduated scale are in a galvanised steel design. Supports are in plastic DIMENSIONS AND WEIGHT, EPS EPS Dim. D B L H Weight [kg] , , , , , ,6 Table1 ORDER CODE, EPS EPS Product Dimension: Ø100 - Ø315 H EPS-250 EPS dimension Ø250. ØD B L Fig. 1 83

84 Rego-T Rego-T is a user-friendly commissioning damper with an extremely low noise level. The unit is intended for manual operation only, and correct installation according to air flow is crucial. NB! Actuatorcontrolled operation is not possible. Max operating temperature for the damper is 100 C. DIMENSIONS AND WEIGHT, Rego-T Min. width: 200mm. Max width: 1400mm. Module: 50mm Min. height: 50mm. Max height: 1400mm. Module: 50mm Weight in kg = damper area in m² x factor 20. Rego-T is available in 3 different designs. 1. Height (H) = 50, 75, 100 and 150mm with one damper-blade only. NB! For installation in duct with internal insulation, dimensions must be taken into consideration for the 150mm unit as the damper blade protrudes from the damper frame. 2. Standard design with damper blades moving in opposite directions as shown in fig mm module. 3. Standard design with circular spigot available in dim. from and incl. Ø400 to and incl. Ø1250, shown as D in fig. 2. Shut-off level is max 90%. The damper lever is equipped with a graduated scale, and can be locked in position with 2 thumbscrews. Damper blades are pinion operated. Rego-T is available in other materials and/or dimensions on request. Frame profiles and damper blades are supplied in a galvanised steel finish, pinion in PBT plastic. Rego-T in dimensions Ø400, Ø500 and Ø630, featuring circular connection collars, are fitted with EPDM rubber gaskets. ORDER CODE, Rego-T Rego-T / 0-0 Product B = Width H = Height SM = Special material SA = Circular connection, Ø400 - Ø1250 Rego-T / 0-0 Rego-T, rectangular damper, 1200 width and 800 height Fig. 1, Rego-T. Fig. 2, Rego-T, with circular spigot 84

85 Iris Iris is an air-flow regulation and measuring damper compliant with the air tightness requirements of EN 1751, Class C. Iris comprises an adjustable diaphragm which can be controlled with an adjusting nut or the enclosed handle, adjustment scale and air flow rate measuring nipples. Iris is made of hot-dip galvanised steel. Measuring nipples and adjustment devices are in plastic. The damper is fitted with a rubber gasket. ORDER CODE, Iris DIMENSIONS AND WEIGHT, Iris Dim. d D L A Weight [kg] , , , , , , , , , , , , ,0 Table 1 Iris Product Dimension Ø80 - Ø800 Iris-250 Iris, dimension Ø250. Fig 1: Iris, dimension 80 Fig 2: Iris, dimension

86 Leo Leo is a volume flow controller which works independently of the duct pressure. It is the desired air flow rate at choked damper that determines the duct pressure required for the applicable unit/string. The VAV unit is based on dynamic measurement of volume flows, and controls the damper position to maintain the air flow rate required. When a change in duct pressure occurs, such as when other volume flow controllers on the branch open or close, the unit will compensate by adjusting the damper until the correct volume flow has been restored. The required air flow rate can, for example, be provided as a 0-10V signal from room thermostat / CO² sensor in the occupied zone covered by the unit. Minimum and maximum air flow rates can be set at the factory or during installation by using a service tool from Belimo. The VAV unit is designed to provide comfort ventilation at temperature conditions of between 0 C and 50 C and a relative humidity between 5% and 95% without condensation. A 4-conductor cable connects the controller to various control equipment in the room. Consistent use of a common reference system for all equipment is important. For the VAV controller, cable no. 1 is system-0. All control and measurement signals are linked up in accordance with this. Wiring diagram for Leo in combination with various room control equipment is available at our website. For energy-efficient operation, VAV systems are equipped with pressure sensors in the ductwork, which transmit control signals to branch dampers or to the fan frequency control. Please see schematic diagram in fig.1. Explanation to fig. 1 1) Pressure sensor for fan control 2) VAV unit 3) Motorised damper with pressure control system 4) Pressure sensor 5) Fan FUNCTION Leo will always adjust to the air flow rate consistent with the signal transmitted from the room control equipment. The VAV unit comprises an adjustable damper and measuring station for air flow rate, and the measurement principle is dynamic measurement of the air flow. In the damper motor s control unit, should the admission for the damper is regulated according to the desired should-value. Leo has an adjustment range shown in table 2. Deviation for working range 10-20% of Vnom:±25% 20-40%: <±10% %: <±4% If T-pipes are used, a spacing of at least 5 x ØD is recommended in order to maintain the measurement accuracy. ORDER CODE, LEO Type: 0 = Not Encased D = Encased Controller Option: 0 = MP-Bus MOD = MOD LON = LON KNX-B = Belimo KNX XAC = X-AIRCONTROL ELP = EasyLink plug ELC = EasyLink Connect Leo / L1-0 A = ASN, extraction unit with mesh grille Sound attenuator: 0 = Without sound attenuator K = LEV-K (Length 500mm) L = LEV-L (Length 1000mm) Type: 1,2,3 or 4 see fig 2 Dimension: Ø100 - Ø Leo / L1-0 Leo not encased, MP-bus, dim Ø160. Delivered with sound attenuator LEV-L, lenght 1000mm, type 1, Ø Fig. 1: Pressure conditions in VAV system 86

87 Leo Leo VAV is a complete measuring and control unit where the air flow rates in ventilation systems can be set as required. At the measuring station, the differential pressure is measured via measuring rod integrated in the unit. The unit is installation-friendly in terms of straight ducting, and can thus be mounted in most ductwork sections. It is fully compliant with air permeability class 4 for damper in closed position, and class C for leakage to the surroundings. Leo is equipped with VAV controller from Belimo or Siemens. Controller specifications are provided in the table below. Full technical documentation can be downloaded from our website Belimo LMV/NMV-D3 is used as analog control or for MP-bus. Belimo LON or MOD-bus controller is also available. For KNX, Belimo LMV-D3-KNX and NMV-D3-KNX is available. If additional protection against structure-borne noise is required, e.g. for open installation, the unit can be delivered with external insulation and casing. This will reduce the level of noise emitted from the actual unit at high choke pressure and high velocity past the damper. However, this should be followed up with additional protection against structure-borne noise from the duct at both sides of the unit. Please see acoustic datasection. The LEV sound attenuator is designed for VAV systems, and is available in 500mm and 1000mm lengths. LEV has a full attenuator cross-section, and this ensures a low-level pressure loss. It is insulated with mineral wool featuring a reinforced top layer to prevent fibres breaking away with the supply air. An extraction unit with mesh grille, ASN, in the same design as LEV is also available. Leo-D, LEV and ASN can be delivered pre-assembled with ducting clips and are equipped with adjustable brackets from factory. Leo Leo comes in a galvanized steel design. The measurement unit is in aluminium. Tubing, nipples and motor casing are in plastic. Leo s connection collars are fitted with EPDM rubber gaskets. LEV is made of galvanised steel, and comes with mineral wool and a glass fibre layer as attenuation material. Connection collars are fitted with EPDM rubber gaskets. ASN is made of galvanised steel and is equipped with an EPDM rubber gasket on the connection collar. LMV-D3-MP/MOD/LON NMV-D3-MP/MOD/LON Operating voltage AC 24 V 50/60 Hz, DC 24 V AC 24 V 50/60 Hz, DC 24 V Power drain consumption 36 2W 3W Dim effect 4 VA (max. 8 5 ms) 5 VA (max. 8 A@ 5 ms) Table 1: Technical specifications, Belimo VAV controller QUICK SELECTION [m³/h] Dim. Max [V nom] Min Table 2: The table shows max. and min. air volumes. Dimensions available: Dimensions available: Dimensions available: Leo-D and LEV type 3 and 4 are delivered with ducting clips Dimensions available: *Only available in length 1000 mm. Fig. 2 87

88 Leo DIMENSIONS AND WEIGHT Dim. D DA B L Table 3 Weight [kg] Dim. Leo Leo-D LEV-500 LEV-1000 ASN 100 1,6 3,2 3,3 5,8 1, ,8 3,5 3,8 6,6 1, ,1 4,1 4,5 7,8 2, ,5 4,9 5,3 9,0 2, ,8 8,0 6,4 11,0 3, ,8 9,8 7,2 12,4 3, ,0 12,0 9,6 15,6 5, ,7 23,0 18,8 6, ,5 28,0 23,1 8,7 Table 4 OD L Fig. 3, Leo Fig. 4, Leo-D 500/1000 OB ODA OD OD OB L 300 ODA OB Fig. 5, LEV Fig. 6, ASN (extraction unit) 88

89 TSK TSK is mainly used in rectangular ventilation ducts for shut-off, volume flow and pressure control. The damper meets the requirements for air permeability class 3. DIMENSIONS AND WEIGHT, TSK Weight approx. 25kg/m² TSK is delivered as a 50mm width and height module as standard, and is equipped with guide spigot. Actuator is available as accessory. On request, the damper can be supplied with a flange spigot or adapted to fit circular ducts. The damper is also available in air permeability class 4. Max. dimensions, complete damper unit: W=2600 x H=2000 The damper s operating temperature is 100 C max. Frame profiles are made in galvanised steel, whereas the damper profiles are in an aluminium design and equipped with silicone moulding for air tightness. The damper shaft is made in Zytel Super Tough nylon and the bushings in Delrin. Fig. 1: Dimensions, damper class 3 with guide spigot ORDER CODE, TSK TSK / 0 / Product B = Width H = Height M = Equipped with actuator (Actuator type must be specified) 4 = Damper class S = Circular spigot (Ød must be stated). F = Flange TSK /0/0-0-0 TSK airtight damper class 3. Width: 600 Height: 400. Fig. 2: Dimensions, damper class 3 with flange spigot Actuator Function Torque Height Weight Max. area [Nm] [mm] [kg] TSK [m²] SF24 / SF230 On/Off spring return ,0 / 3,3 2,6 SF24-SR Modulating spring return ,7 2,6 NM24A / NM230A On/Off ,8 / 0,8 2,0 NM24A-SR / NM230A-SR Modulating ,8 / 0,9 2,0 SM24A / SM230A On/Off ,0 / 1,1 2,6 SM24A-SR / SM230A-SR Modulating ,1 / 1,2 2,6 Table 1 (Damper height from 1400 up to 2000 requiers 2 actuators) 89

90 LEV LEV is a circular sound attenuator for use in ductwork. LEV is a circular steel unit lined with attenuation material inside. Available in both 500 mm and 1000 mm lengths. LEV complies air tightness class C. LEV is made of galvanised steel with mineral wool and a glass fibre layer as attenuation material. Connection collars are fitted with EPDM rubber gaskets. DIMENSIONS AND WEIGHT, LEV LEV Weight [kg] Dim. D A L LEV 500 LEV /1000 3,3 5, /1000 3,8 6, /1000 4,5 7, /1000 5,3 9, /1000 6,4 11, /1000 7,2 12, /1000 9,6 15, , ,1 Table 1 LEV Type 0 Available dimensions: * * ORDER CODE, LEV LEV / 0-0 Dimension: Ø100 Ø630 Length: 500 or 1000 A = ASN, extraction unit with mesh grille Type 0,1,2,3 or 4. See fig. 2 LEV Type 1 Available dimensions: * * LEV /0-0 LEV, dimension Ø160, length 1000mm, type 0 LEV Type 2 Available dimensions: LEV Type 3 Available dimensions: * * Fig. 2. Dimensional sketch LEV, Type 0 LEV Type 4 Available dimensions: * Available in 1000mm lengths only Fig. 1 90

91 LKR LKR is a square sound attenuator with circular end spigots. LKR-V is a square sound attenuator with a circular end and side spigot in order to accommodate a right-angled bend. LKR and LKR-V comprise a square steel unit where all 4 internal walls are lined with mineral wool with a glass fibre layer. From dimension Ø315 and up, all sound attenuators are equipped with a centre baffle. LKR and LKR-V complies air tightness class C. LKR and L KR-V are supplied in a galvanised steel finish. The units from dimension Ø100 up to Ø630 are fitted with EPDM rubber gasket on the connection collars, remaining dimensions without rubber gasket. Internally, the units are lined with mineral wool with a glass fibre layer. DIMENSIONS AND WEIGHT, LKR LKR Weight [kg] Dim. L = 300 L = 600 L = 900 L = 1200 L = ,8 3 3,9 5, ,2 3,5 4,6 6, ,7 4,5 5,8 7, ,3 5,4 7,3 9, ,3 6,8 9, ,6 9,2 11, ,7 15,4 19, , , , Table 1: LKR and LKR-V QUICK SELECTION In order to ensure the optimum choice of LKR, please use the Attenuator Selection computer program available for download from our website: ORDER CODE, LKR Fig.1, LKR 91

92 LKK LKK is a rectangular sound attenuator for installation in rectangular ducting. DIMENSIONS AND WEIGHT, LKK AND LKK-V LKK is a rectangular steel unit featuring internal vertical splitters with mineral wool with a glass fibre layer inside. The unit is equipped with a flanged connection at each end. LKK is available in heights from 400 mm to 3000 mm (100 mm increments), and in widths from 600 mm to 3000 mm (100 mm increments), and in lengths of 640, 1240, 1500, 1800 and 2480 mm and 2480 mm systems are delivered as two-piece units. An LKK-V version is also available, and is a sound attenuator with connection collars forming a right angle in order to accommodate a right-angled bend. LKK and LKK-V complies air tightness class C. LKK comes in a galvanised steel design. The flanged joint is equipped with a polyethylene gasket. Splitters with mineral wool with a glass fibre layer have been fitted inside. QUICK SELECTION In order to ensure optimum splitter combination, an Attenuator Selection computer program has been developed and is available for download from our website: Fig. 1, LKK ORDER CODE, LKK LKK / 3125D / 0-0 Product B = Width H = Height L = Length: 640, 1240, 1500, 1880 or 2480 L = Enamel finish SM = Special material K = Code (available in table 1-8: or from LKK / 3125D / 0-0 LKK, width 1200, height 500, length 1500, code: 3125D. ORDER CODE, LKK-V LKK-V / 0-0 Product B = Width H = Height I = IN dimension L = Enamel finish SM = Special material U = OUT-dimension LKK-V / 0-0 LKK-V, width 1200, hight 600, IN dimension 300 and OUT dimension 300. Fig. 2, LKK-V 92

93 LKL LKL is a rectangular sound attenuator for installation in rectangular ducting. LKL is a rectangular steel unit with internal splitter. The unit is equipped with a flanged connection at each end. LKL is available in heights from 150 mm to 400 mm (50 mm increments), and in lengths of 640, 1000, 1240 and 1500 mm. Widths in 50 mm increments. LKL complies air tightness class C. LKL comes in a galvanised steel design. The flanged joint is equipped with a polyethylene gasket. A splitter with mineral wool with a glass fibre layer has been fitted inside. DIMENSIONS AND WEIGHT, LKL *Weight is calculated by using the formula: factor x B X L, with B and L specified in metres. Height Width Length [mm] Weight* [kg] , ,5 x B x L 1240, , ,0 x B x L 1240, , ,8 x B x L 1240, , ,2 x B x L 1240, , ,0 x B x L 1240, , ,0 x B x L 1240, 1500 Table 1 QUICK SELECTION In order to ensure correct/optimum splitter combination, an Attenuator Selection computer program has been developed and is available for download from our website: Length ORDER CODE, LKL LKL / 0-0 Product L = Painted finish B = Width SM = Special material H = Height L = Length; 640, 1000, 1240 or 1500 LKL / 0-0 LKL, width 500, height 350 and length 1240 Width Heigt Figur 1 93

94 ILP and ILS ILP and ILS are access door systems for cleaning and inspection of rectangular and circular ducts. The access doors are also available as insulated units. Insulated version inspection hatchet with quick-release clamps: The access door system comprises: Door panel, frame and neoprene gasket Quick-release clamps are used to attach the panel, and the unit is lined with Rockwool for thermal and acoustic insulation. The frame is designed to provide the correct compression at clamp ends, and this ensures that the panel is held in place. A tooth-grip profile is used to secure the frame to the duct, and allows for easy installation in duct wall. In order to ensure adequate sealing between panel, frame and duct wall, the frame has been fitted with a neoprene gasket on both the inside and the outside. MATERIAL AND SURFACE COATING The access doors come in a galvanised steel finish, and are compression moulded for improved strength/density. ORDER CODE, ILP ILP = Uninsulated ILP-I = Insulated ILP ILP ILP uninsulated, dimension 300x200. Dimensjon: = 250x = 300x = 450x = 600x450 Ø20 = Ø200, (uninsulated only) DIMENSIONS AND WEIGHT, ILP ILP Access door dimension ILP ILP-I Dim. [mm] Weight [kg] Weight [kg] x 150 0,7 0, x 200 1,1 1, x 350 2,8 2, x 450 4,9 3,9 Ø 200 Ø200 0,5 - Table 1 DIMENSIONS AND WEIGHT, ILS ILS Access door dimension Weight Dim. [mm] [kg] 100/ x 80 0, x 80 0, x 150 0, x 150 0, x 150 0, x 150 0, x 300 1, x 300 1, x 300 1, x 300 1,4 Table 2 INSTALLATION Grooves in ducting are cut by using the template provided. MAINTENANCE No specific maintenance requirements. ORDER CODE, ILS ILS ENVIRONMENT Enquiries regarding product declaration can be directed to our sales team, or information can be found at our website: Product ILS-315 ILS for duct dimension Ø315. For duct dimension: Ø100/Ø125, same. Ø160 to and incl. Ø

95 KSA KSA is a duct connection system for rectangular ductwork. Sealant has been applied to the KSA duct connector base. ORDER CODE, KSA KSA - SSA / KPA KSA = Duct connector SSA = C-clip track profile KPA = Gasket KIA = Inner bend YH1 = Outer bend The duct connection system comes in a galvanised steel design. KSA-SSA / 0-0-KPA KSA duct connector, SSA c-clip track profile and KPA gasket. DIMENSIONS AND WEIGHT, KSA As specified in fig. 1 1 Outer bend, type YH-1 2 C-clip track profile, type SSA [0.21 kg/m] 3 Duct connector, type KSA [0,42 kg/m] 4 Inner bend, type KIA 5 Gasket, type KPA KSA connectors are delivered in 3m lengths, 50m per bundle. KPA gaskets are delivered in 1.5 m lengths, 100m per bundle. SSA profiles are delivered in 3m lengths, 100m per bundle. KIA bends are delivered in packs of 500. YH-1 bends are delivered in packs of 500. INSTALLATION KSA and SSA profiles are delivered in 3m lengths, 50m and 100m per bundle respectively, and are cut to size using saw, cut-off wheel or similar. A manual (KPH) or pneumatic (KPL) hand-press can also be used to cut the KSA connector in lengths = B/H 10mm. Please see fig. 1. The KSA connector is pressed onto the duct end until it is fully attached, and can be secured as follows: fig. bolted, screwed or spot welded as shown in fig. 2 (A), or secured with compressing pliers as shown in fig. 2 (B). When all four sides of the KSA connector have been attached, the KIA inner bend is fitted and can be fixed in place by using compressing pliers. The KPA gasket is attached to the profile as shown in fig. 1, and the duct units can then be connected using the SSA track profile. When the sections have been joined, the YH-1 outer bend is fitted. Figure 1 MAINTENANCE No specific maintenance requirements. ENVIRONMENT Enquiries regarding product declaration can be directed to our sales team, or information can be found at our website: Figure 2 Assembly 95

96 Svalbard-H Svalbard-H is a hydronic cooling, heating and ventilation system for use in offices, shops, schools etc. The system is designed to provide excellent cooling effect, and a high induction level ensures a draft-free environment in the occupied zone. Svalbard-H is made for corner installation, i.e. between wall and ceiling. FUNCTION Air is supplied via nozzles, and indoor air is extracted and fed through the coil. Effective mixing of indoor air and supply air, i.e. induction, minimises the risk of draft in the occupied zone. When Svalbard is utilised for heating, the same technique is used for dispersion of heat along the ceiling. The indoor air is extracted through the perforated area on the unit s front-panel in order to avoid dirt accumulation on the ceiling. Nozzle configuration for the chilled beam, i.e. desired air supply and pressure, is specified at time of order. Svalbard-H comes with integrated air flow rate measuring point. The front panel can be folded down for inspection and cleaning. Svalbard-H is available in installation lengths of 1200, 1800, 2400 and 3000 mm. Coil types: SKB = standard cooling coil or VKB heating and cooling coil. Dispersion type: unidirectional Connection to air: Ø125 mm (spigot dimension). Connection to air and water on same side Connection to water, cooling and heating: Cu Ø15x1.0 mm Changeable flowpattern via Jet Split lamellaes in the beams outlet, standard pattern is fan style. Blind cover can be provided for adaptation to the wall. See Figure 9. MATERIAL ANDSURFACE TREATMENT Frame and casing in galvanised steel. Delivered in a powdered painted finish (white RAL gloss 30) as standard. Copper tube coils with aluminium lamellae. Adjustable lamellae are in a plastic design. DIMENSIONS AND WEIGHT, Svalbard-H ORDER CODE, Svalbard-H Svalbard-H SKB - A - 1 / S - 0 Product SL = Special finish L = Length: 1200, 1800, 2400 S = Damper, DRS-K Ø125 A1 = Actuator 24V, off/on or 3000 A2 = Actuator 230V, off/on Pre-set value, W = TROX TRV 2-way valve from Auracool. Coil type: *Connection to water, see fig. 2 1 or 2 SKB = Standard cooling coi VKB = Heating and cooling coil *Connection to air, see fig. 2 A or B Svalbard-H SKB-A-1/0-0-S-0 Svalbard-H, corner beam, length 1800 w/ pre-set value 55 and standard cooling coil Connection to air A and water 1. Commissioning damper DRS-K Ø125 supplied separately. Connection to air and water on same side as standard, A-1or B-2. ACCESSORIES See order code, pre-installed in chilled beam. W = TROX TRV 2-way valve, Broen (see separate data sheet). A1 = Actuator 24V on/off, Broen (see separate data sheet). A2 = Actuator 230V on/off, Broen (see separate data sheet). ACCESSORIES Ordered and supplied separately. Ballorex Dynamic valve (see separate data sheet). Actuator: 24V, 230V or 24V modulating 0-10V signal. Transformer, EasyTrafo 75 VA (see separate data sheet). Transformer, EasyTrafo 105 VA (see separate data sheet). Room controller, EasyReg (see separate data sheet). Length L Weight* Weight: water in cooling coil [kg] [mm] [mm] [kg] SKB VKB ,0 1,0 0, ,5 1,5 1, ,5 2,1 1, ,0 2,6 2,0 Table 1 (* No water in cooling coil) Fig. 2 Brackets Cooling Brackets Cooling/heating Cooling Heating Cooling/heating Brackets Brackets Heating 96 Fig. 1, Svalbard-H

97 Svalbard-H QUICK SELECTION, Svalbard-H The tables state the cooling effect from the chilled beam s water circuit and the emitted sound power level from the beam. In order to calculate total cooling effect, the cooling effect of the supply air must be added as shown in the example below. Examplel Svalbard-H1800 Battery type: Standard Water-side cooling effect at 40 Pa as per table 3 = 310 W Air flow rate: 80 m³/h Supply-air cooling effect: q/3600 x 1,2 x c p x t room-supply air:: = t room-water: 10 0 C 80/3600 x 1,2 x 1010 x 6 = 160 W t room-supply air: 6 0 C Total cooling effect = 470 W Svabard-H-1200 mm t k [ C] L w db(a) Total pressure in duct [Pa] Pa 80 Pa Air flow rate [m³/h] Table 2: Cooling effects at 0.06 litres of water per sec Svabard-H-1800 mm t k [ C] L w db(a) Total pressure in duct [Pa] Pa 80 Pa Air flow rate [m³/h] Table 3: Cooling effects at 0.06 litres of water per sec Svabard-H-2400 mm t k [ C] L w db(a) Total pressure in duct [Pa] Pa 80 Pa Air flow rate [m³/h] Table 4: Cooling effects at 0.06 litres of water per sec Svabard-H-3000 mm t k [ C] L w db(a) Total pressure in duct [Pa] Pa 80 Pa Air flow rate [m³/h] Table 5: Cooling effects at 0.06 litres of water per sec 97

98 Svalbard-I Svalbard-I is a hydronic cooling, heating and ventilation system for use in offices, shops, schools etc. The system is designed to provide a draft-free cooling effect in the occupied zone. Svalbard-I is suitable for integration in a ceiling grid with 600mm modules. FUNCTION Air is supplied via nozzles, and indoor air is extracted and fed through the coil. Effective mixing of indoor air and supply air, i.e. induction, minimises the risk of draft in the occupied zone. When Svalbard-I is used for heating, the same technique is used for dispersion of heat along the ceiling. The indoor air is extracted through the perforated area on the unit s front panel in order to avoid dirt accumulation on the ceiling. Nozzle configuration for the chilled beam, i.e. desired air supply and pressure, is specified at time of order. Svalbard-I is delivered with integrated pressure outlet for air flow rate measurements. The front panel can be folded down for inspection and cleaning. Dispersion options: symmetrical 50/50 or asymmetrical 75/25 (25/75) can be adjusted on site. Connection to air: Svalbard-I, 175mm height, is equipped with a Ø125 spiro connection at gable end (spigot dimension). Fig. 1 and 2. Svalbard-I, 235mm height, is available with Ø125 side spigot. For alternative positioning options, see fig. 1 & 3 and under order code. Svalbard-I can be supplied in a low profile design, 150 mm, with Ø100 spiro connection at gable end. Connection to water: copper pipe, Ø15x1.0 mm. Delivered with vertical pipe-ends as standard (see fig. 1, 2 & 3 and under order code). changeable flowpattern via Jet Split lamellaes in the beams outlet, standard pattern is fan style. Frame and casing in a galvanised, steel-plated finish. Delivered in white enamel finish ((RAL glans 30) as standard. Copper tube coils with aluminium lamellae. Adjustable lamellae are in a plastic design. ORDER CODE, Svalbard-I-L Low overhall heigth, 175 mm. Svalbard-I-L SKB - A /50 / W - A1 - S - 0 Product SL = Special finish Length: S = Damper, DRS-K Ø , 1800, 2400 A1 = Actuator 24V, on/off or 3000 A2 = Actuator 230V, on/off Preset value W = TROX TRV 2-way valve from Auracool Flow pattern, X/Y: Coil type: Symmetrical: standard 50/50 SKB = Standard cooling coil Asymmetrical: 75/25 or 25/75 HKB = High-capacity coil */**Connection to water: VKB = Heating and cooling coil 3 or 4 Vertical (standard) *Connection to air: 1 or 2 Horizontal (additional) A or B Svalbard-I-L SKB-A-3-50/50 / W-A1-S-0 Explantation: Svalbard-I for integration in modular ceiling sy stems, low overall heighth 175 mm and length 1800, preset value 118. Standard coil, connection to air at gable end Ø125, standard flow pattern 50/50. TROX TRV 2-way valve and 24V actuator fitted, Damper DRS-K Ø125 supplied separately. *Standard air and water connection is A3 or B4 (see fig. 1). **Water connection is supplided as standard vertic al (3 or 4), alternative horizonatal water connection (1 or 4) will be delivered with push-fit coupling with smooth end installed. ORDER CODE, Svalbard-I-H Height 235 mm. Svalbard-I-H SKB - A /50 / W - A1 - S - 0 Product SL = Special finish Length: S = Damper, DRS-K Ø , 1800, 2400 A1 = Actuator 24V, on/off or 3000 A2 = Actuator 230V, on/off Preset value W = TROX TRV 2-way valve from Auracool Flow pattern, X/Y: Coil type: Symmetrical: standard 50/50 SKB = Standard cooling coil Asymmetrical: 75/25 or 25/75 HKB = High-capacity coil */**Connection to water: VKB = Heating and cooling coil 3 or 4 Vertical (standard) *Connection to air: 1 or 2 Horizontal (additional) Gable: A or B (L= ) Side connection: C,D,E or F (L= ) CD or EF. (***L= 3000) Svalbard-I-H SKB-A-3-50/50 / W-A1-S-0 Explantation: Svalbard-I for integration in modular ceiling systems, height: 235 mm. and length 1800, preset value 105. Standard coil, connection to air at gable end Ø125, standard flow pattern 50/50. TROX TRV 2-way valve and 24V actuator fitted. Damper DRS-K Ø125 supplied separately. *Standard air and water connection is A3 or B4 (see fig.1). is supplied as standard vertical (3 ACCESSORIES See order code, supplied mounted in beam. W = TROX TRV 2-way valve, Broen. See separate data sheet. A1 = Actuator 24V on/off, Broen. See separate data sheet. A2 = Actuator 230V on/off, Broen. See separate data sheet. Fig. 1 (spigot C to F only available for 235 mm height) ACCESSORIES Ordered separately and supplied loose. Ballorex Dynamisk valve. See separate data sheet. Actuator: 24V, 230V or 24V modulating 0-10V signal. Transformator EasyTrafo 75 V A. See separate data sheet. Transformator EasyTrafo 105 V A. See separate data sheet. Room controller EasyReg. See separate data sheet. 98

99 Svalbard-I QUICK SELECTION Svalbard-I The tables state the cooling effect from the chilled beam s water circuit and the emitted sound power level from the beam. In order to calculate total cooling effect, the cooling effect of the supply air must be added as shown in the example below. Example Svalbard-I 1800 Battery type: Standard Water-side cooling effect at 40 Pa as per table 2 = 580 W Air flow rate: 75 m³/h Supply-air cooling effect: q/3600 x 1,2 x c p x t room-supply air: = t room-water(mid.): 10 K 75/3600 x 1,2 x 1010 x 6 = 152 W t room-supply air: 6 0 K Total cooling effect = 732 W Svabard-I-1200 mm t k [ C] L w db(a) Total pressure in duct [Pa] Low, gable High, gable High, side Coll type SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB 40 Pa 80 Pa 40 Pa 80 Pa 40 Pa 80 Pa <20 27 <20 29 < < Table 1: Cooling effects at 0.06 litres of water per sec. Air flow rate Svabard-I-1800 mm t k [ C] L w db(a) Total pressure in duct [Pa] Low, gable High, gable High, side Coll type SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB 40 Pa 80 Pa 40 Pa 80 Pa 40 Pa 80 Pa <20 24 <20 23 < <20 26 < Table 2: Cooling effects at 0.06 litres of water per sec. Air flow rate Svabard-I-2400 mm t k [ C] L w db(a) Total pressure in duct [Pa] Low, gable High, gable High, side Coll type SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB 40 Pa 80 Pa 40 Pa 80 Pa 40 Pa 80 Pa <20 24 <20 23 < <20 26 <20 26 < Table 3: Cooling effects at 0.06 litres of water per sec. Air flow rate [m³/h] [m³/h] Svabard-I-3000 mm t k [ C] L w db(a) Total pressure in duct [Pa] Low, gable High, gable High, side Coll type SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB 40 Pa 80 Pa 40 Pa 80 Pa 40 Pa 80 Pa <20 26 <20 28 < <20 29 <20 29 < Table 4: Cooling effects at 0.06 litres of water per sec. Air flow rate [m³/h] [m³/h] 99

100 Svalbard-I DIMENSIONS AND WEIGHT, Svalbard-I H=175 Length L L2 Weight* Weight: water in cooling coil [ [kg] [mm] [mm] [mm] [kg] SKB HKB VKB ± ,5 1,0 0, ± ,8 1,5 1, ± ,0 2,1 1, ± ,3 2,6 2,0 Table (* No 3594 water 3634±10 in cooling coil) 48 1,6 3,1 2,4 DIMENSIONS AND WEIGHT, Svalbard-I H=235 Length L L2 Weight* Weight: water in cooling coil [ [kg] [mm] [mm] [mm] [kg] SKB HKB VKB ± ,5 1,0 0, ± ,8 1,5 1, ± ,0 2,1 1, ± ,3 2,6 2,0 Table (* No 3594 water in 3634±9 cooling coil) 52 1,6 3,1 2,4 Fig. 2: Svalbard-I H=175 Fig. 3: Svalbard-I H=

101 Svalbard-F Svalbard-F is a hydronic cooling, heating and ventilation system for use in offices, shops, schools etc. The system is designed to provide excellent cooling effect, and a high induction level ensures a draft-free environment in the occupied zone. Svalbard-F is designed for open installation in ceiling or covering. FUNCTION Air is supplied via adjustable nozzles which ensure that the air is dispersed along the ceiling in a fan-shaped flow pattern. This technique optimises the dispersion effect by providing a larger area for the supply air and indoor air to mix. Such effective mixing of indoor air and supply air, i.e. induction, minimises the risk of draft in the occupied zone. Svalbard systems which are used for heating only utilises the same technique for effective dispersion of heat along the ceiling. The secondary air is extracted through the perforated area on the unit s frontpanel in order to avoid dirt accumulation on the ceiling. ORDER CODE, Svalbard-F Svalbard-F SKB - A /50 / W - A1- S - 0 Product L = Length: 1200, 1800, 2400 or 3000 Pre-set value from Auracool Coil type: SKB = Standard cooling coil Flow pattern, X/Y: HKB = High-capacity coil Symmetrical: standard 50/50 VKB = Heating and cooling coil Asymmetrical: 75/25 or 25/75 *Connection to air, see fig. 2: *Connection to water, see fig. 2: A = Standard B = Special 1 = Standard 2 = Special SL = Special finish S = Damper, DRS-K Ø125 A1 = Actuator 24V off/on A2 = Actuator 230V off/on W = TROX TRV 2-way valve Svalbard-F SKB-A-1-50/50 / W-A1-S-O Svalbard-F for open installation, 1800mm length, pre-set value 104. Standard coil and connection to air Ø125 (A1), symmetrical flow pattern 50/50. Water valve TROX TRV and 24V actuator fitted, commissioning damper DRS-K Ø125 supplied separately. *Connection to air and water will be on gable A1 or B2 as standard (see fig.2). Nozzle configuration for the chilled beam, i.e. desired air supply and pressure, is specified at time of order. Svalbard-F is delivered with integrated pressure outlet for air flow rate measurements. The front panel can be folded down for inspection and cleaning. Svalbard-F is available in installation lengths of 1200, 1800, 2400 and 3000 mm. Dispersion options: symmetrical 50/50 or asymmetrical 75/25 (25/75) can be adjusted on site. Connection to air: gable end Ø125 mm (spigot dimension). Connection to water: Cu Ø15 x 1, 0 mm. Changeable flowpattern via Jet Split lamellaes in the beams outlet, standard pattern is fan style. Blind cover can be provided for adaptation to the wall. See Figure 9. ACCESSORIES- See order code, delivered fitted in chilled beam. W = TROX TRV 2-way valve, Broen (see separate data sheet). A1 = Actuator 24V on/off, Broen (see separate data sheet). A2 = Actuator 230V on/off, Broen (see separate data sheet). ACCESSORIES - Ordered and supplied separately. Ballorex Dynamic valve (see separate data sheet). Actuator: 24V, 230V or 24V modulating 0-10V signal. Transformer, EasyTrafo 75 VA (see separate data sheet). Transformer, EasyTrafo 105 VA (see separate data sheet). Room controller, EasyReg (see separate data sheet). Frame and casing in a galvanised, steel-plated finish. Delivered in a powdered painted finish (white RAL gloss 30) as standard. Copper tube coils with aluminium lamellae. Adjustable lamellae are in a plastic design. DIMENSIONS AND WEIGHT, Svalbard-F Length L Weight * Weight: water in cooling coil [kg] [mm] [mm] [kg] SKB HKB VKB ,5 1,0 0, ,8 1,5 1, ,0 2,1 1, ,3 2,6 2,0 Table 1 (* No water in cooling coil) Fig. 2 Fig

102 Svalbard-F QUICK SELECTION, Svalbard-F The tables state the cooling effect from the chilled beam s water circuit, and the emitted sound power level from the beam. In order to calculate total cooling effect, the cooling effect of the supply air must be added as shown in the example below. Example Svalbard-F 1800 Battery type: Standard Water-side cooling effect at 40 Pa as per table 3 = 580 W Air flow rate: 75 m³/h Supply-air cooling effect: q/3600 x 1,2 x c p x t room-supply air: = t room-water: 10 0 K 75/3600 x 1,2 x 1010 x 6 = 152 W t room-supply air: 6 0 K Total cooling effect = 732 W Svabard-F-1200 mm t k [ C] L w Total pressure in duct [Pa] db(a) Coil type SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB 40 Pa 80 Pa < < Table 2: Cooling effects at 0.06 litres of water per sec. Air flow rate [m³/h] Svabard-F-1800 mm t k [ C] L w Total pressure in duct [Pa] db(a) Coil type SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB 40 Pa 80 Pa < < Table 3: Cooling effects at 0.06 litres of water per sec Air flow rate [m³/h] Svabard-F-2400 mm t k [ C] L w Total pressure in duct [Pa] db(a) Coil type SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB 40 Pa 80 Pa < < Table 4: Cooling effects at 0.06 litres of water per sec. Air flow rate [m³/h] Svabard-F-3000 mm t k [ C] L w Total pressure in duct [Pa] db(a) Coil type SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB SKB HKB 40 Pa 80 Pa < < Table 5: Cooling effects at 0.06 litres of water per sec. Air flow rate [m³/h] 102

103 DID-614 Active chilled beams of type DID614 for the integration into various ceiling systems, preferably for room hights up to 4.20 m. Particularly suitable for grid ceilings with grid size 600 or pipe or 4-pipe heat exchangers enable good comfort levels with a low conditioned primary air volume flow rate. Energy-efficient solution since water is used as a medium for heating and cooling. JetSplit adjustable air control blades allow for the manual adjustment. Large volum flow rate range due to the adjustable twin nozzles (optional). Four-way air discharge. Horizontal heat exchanger as 2-pipe or 4-pipe system. Water connection, Ø12 mm Cu pipe or coupling with 1/2" external thread or 1/2" internal thread. Adjustable nozzle configuration for a large volume flow range. Spigot is suitable for circular ducts to EN 1506 or EN Removable front fixed with magnets with safety cables. 4 suspension points for on-site installation. Five nozzle variants to optimise induction MATERIALS AND FINISH Casing, spigot, nozzle plate, and front made of galvanised sheet steel. Heat exchanger with copper tubes and aluminium fins. Exposed surfaces are powder-coated with RAL JetSplit-air control blades made of polypropylene, UL 94, flame retardant (V0). Order code, DID-614 Order code DID614 D1 4 HE R A1 / 593 x SL RAL 9006 / KV24 / HV Type DID614 2 Design variante D1 3 Varme og kjølebatteri Dyse varianter HE S1 S2 HP DA DA-F 5 Plassering av vanntilkobling R L 8 Primærluft anslutning RAL gloss 30 9 SL 10 Kjøleventil - aktuator KV KV 24 KV Varmeventil - aktuator HV HV 24 HV Vanntilkoblinger A1 A2 7 Standard dimensjoner [mm]

104 DID-614 DIMENSIONS AND WEIGHT DID614 Nominal L B L1 L2 G x x Dimensions (mm) D H A Weight (kg) Nominal size kg/piece Contained water (max) 600 x x L2 42,5 42,5 G A A H 12 8 D B L A B L B

105 VIP-X is a complete system for managing and monitoring of VAV systems. It contains a web server with ready web images for configuration of the system. VIP-X can control up to 32 dampers and acquire signals from up to 32 sensors. Up to five VIP-X units may be connected via a switch, so that the total number of dampers and sensors reaches 160. Using damper angle monitoring to set up function for optimum fan operation. VIP-X can communicate via Modbus/TCP, BACnet/IP or KNXnet/IP and can be provided for 16 or 32 dampers. Modbus/TCP will always be implemented, regardless of whether one chooses VIP-X for BACnet/IP or KNXnet/IP. VIP-X consists of a prefabricated unit that contains both a controller with web server, transformers to supply power to all dampers and sensors and connectors for connection via Winsta pluggable cabling system. VIP-X has a robust casing that is manufactured in galvanized sheet steel. It is Winsta terminals for dampers and 230V operating voltage and RJ45 connector for TCP / IP in bottom plate. The unit has four binding lugs for mounting. 105

106 EasyLink EasyLink EasyLink is a complete control system for energy proper management and control of indoor climate in a building. The system can regulate both VAV, heating, cooling, CO2, motion and light at room level. FUNCTION EasyLink system can control up to 240 room controllers with their corresponding temperature sensors in the same system. If higher plant, an EasyLink system expanded by multiple systems connected in series. The system has damperblade control connectable mode for optimal fan operation. EasyLink provides internal communication via EXOline-bus (RS485) and communicate further on EXOline, Modbus and BACnet on TCP / IP. EasyLink system have prefabricated units consisting of an overall system controller (Master), Router, room controller, room sensors, connection cards for connection of cables and cable packages. Connection card has input for 24 V operating voltage or 230 V with built-in transformer. All connectors and cables have interface with RJ-standard and Phoenix plugs for easy connection. MATERIALS AND FINISH Master, Router, CO2 sensor and room controller has robust housing made of polycarbonate. Connection card has sturdy casing made of galvanized steel. DIMENSIONS AND WEIGHT, EasyLink Master/Router: WxHxD = 149x121x60mm, weight = 250 grams Romregulator: WxHxD = 95x95x28mm, weight = 110 grams Koblingskort: WXHXD = 125/225x165x75mm, weight = 560 grams ORDER CODE, EasyLink EasyLink system buildup EasyLink Connect, connection card election 9 in the order code 106

107 NO Head Office/factory PO Box 100 NO-2712 Brandbu Telephone: Telefax: Sales office Sweden Konsumentvägen 17 SE Älvsjö Sales office Sorgenfriveien 9 NO-7037 Trondheim Sales office Fabrikkveien 14 NO-4033 Stavanger Sales office Tvetenveien 152 NO-0671 Oslo Sales office Damsgårdsveien 169 NO-5160 Laksevåg TINT Kommunikasjon 107