Maeda MC285CRM(E) Technical specifi cations

Transcription

1 Maeda MC285CRM(E) Technical specifi cations Offering the best balance of power and design Slim (750mm) Wide Body Programmable Moment Limiter Rubber Tracks Hydrostatic Transmission Tilt Sensor/Alarm Track System for Easier Manoeuvring Specification MC285CRM(E) Crane capacity 2.82 t x 1.4m Max. working radius 8.205m Max. lifting height 8.7m Hook speed 8m / min. (4 falls, 4th layer) Single line speed 32m / min. (4th layer) Hoist rope IWRC 6 x Fi (29) 7mm x 48m Telescopic system Boom length Telescoping speed Boom type 2535m m 6.04m / 22 sec. Fully automatic 5 section pentagonal telescopic boom Boom hoist system Slew system Outrigger system Hoist angle / speed Slew angle / speed Maximum extended dimensions 0-80º / 14 sec. 360º continuous / 2.3 rpm 4 Multi position box type with lock valves (Length) 4580mm x (Front) 4530mm x (Rear) 3810mm Powerful Winch with Hydraulic Disc Brake Fully Automatic Pentagonal Section Boom Cable Remote Controller Traction system Engine Electric motor MC285CRME Drive Travel speed Gradability Crawler length x width Ground pressure Rated output Starting method Fuel / Fuel tank capacity Size Hydrostatic type, stepless forward and reverse km/h 20º 975mm x 200mm 0.44 kg / cm² Yanmar 2TNE68-ME 2 cylinder water cooled diesel 6.57 Kw / 2600 rpm Electric Diesel / 12L Fully enclosed fan cooled motor 5.5 Kw 4P 400V Remote control system Cable remote controller, micro-speed mode, outrigger operation. Dimensions Length x Width x Height MC285CRM Weight MC285CRM Length x Width x Height MC285CRME Weight MC285CRME 2715mm x 750mm x 1440mm 1720kg 3285mm x 750mm x 1440mm 1900kg Standard equipment light, hour-meter, 4-fall hook block, black rubber tracks and safe load indicator. Optional equipment White rubber tracks, single fall hook, two fall hook, searcher hook (300kg max. capacity, weight approx 30kg), radio remote control.

2 Maeda MC285CRM(E) Dimensions Overall Size Outrigger Spread Dimensions Range Chart 8.575m boom 7.075m boom 5.575m boom 4.075m boom 2.535m boom Lifting height (m) The Range Chart does not take into account boom defl ection under load. The maximum reach below ground level is: Four Fall Two Fall Single Fall 10.10m 20.20m 40.20m

3 Maeda MC285CRM(E) Load Charts load Outriggers at Maximum position 4.075m boom 5.575m boom 7.075m boom 8.575m boom < < < < load Outriggers at any other position 4.075m boom 5.575m boom 7.075m boom 8.575m boom < < < < The Total Rated Load Charts are based on the actual working radius including boom defl ection. The weight of the hook (standard 4 fall - 20kg) must be included as part of the load shown in the Total Rated Load Charts. When using two fall or single fall hooks, use the appropriate four fall Total Rated Load Chart above but with a maximum load of: Two Fall kg, Single Fall - 710kg.

4 Maeda MC305CRM(E) Technical specifi cations Offering the best balance of power and design Two Travel Speeds Programmable Moment Limiter Rubber Tracks Hydrostatic Transmission Specification MC305CRM(E) Crane capacity 2.98t x 2.5m Max. working radius 12.16m Max. lifting height 12.52m Hook speed 13.5m / min. (4 falls, 4th layer) Single line speed 54m / min. (4th layer) Hoist rope IWRC 6 x WS(26) 8mm x 73m Telescopic system Boom length Telescoping speed Boom type 3.695m m 8.79m / 26 sec. (38 sec.) Fully automatic 5 section pentagonal telescopic boom Centralised Controls 4 Fall / 2 Fall Hook Block Automatic Hook Stowage System Tilt Sensor/Alarm Boom hoist system Slew system Outrigger system Traction system Hoist angle / speed Slew angle / speed Maximum extended dimensions Drive Travel speed Gradability Crawler length x width Ground pressure 0-80 / 14.5 sec. (21 sec.) 360 / 2.4 rpm (1.7 rpm) Extension and set up by direct acting hydraulic cylinders (Length) 4888mm x (Front) 4504mm x (Rear) 4396mm Hydraulic motor driven, stepless speed changer km/h (1.3 km/h) mm x 300mm 36.3 kpa (0.37 kgf/cm 2 ) Powerful Winch with Hydraulic Disc Brake Engine Rated output Starting method Fuel / Fuel tank capacity Yanmar 3TNV76 3 cylinder water cooled diesel 15.2kw / 2500min -1 (20.7PS/2500rpm) Electric Diesel / 40L Two Speed Winch Fully Automatic Pentagonal Section Boom Cable Remote Controller Electric motor MC305CRME Remote control system Dimensions Standard equipment Optional equipment Size Length x Width x Height Weight MC305CRM Weight MC305CRME Totally enclosed fan-cooled motor 5.5kw, 4P 380V Cable remote controller, micro-speed mode, load display for transmitter, outrigger operation 4285mm x 1280mm x 1695mm 3900kg 4040kg Overwind protection, load indicator, hydraulic safety valve, wire rope latch, level, machine body inclination alarm, EMO switch, travel lock lever, outrigger interlock device, moment limiter, rotary lamp, hour-meter, 4-fall / 2-fall hook block Radio remote control, white rubber tracks, single fall hook, searcher hook.

5 Maeda MC305CRM(E) Dimensions Overall Size 1695mm 2170mm 300mm 300mm 4285mm 1280mm Outrigger Spread Dimensions Range Chart 3370mm 80º 70º 60º 50º mm 4504mm 40º 30º 20º Lifting height (m) 60º 50º 4 10º mm 60º 50º 4504mm 0º mm The Range Chart does not take into account boom defl ection under load. The maximum reach below ground level is: Four Fall Two Fall Single Fall 16.09m 32.18m 64.36m

6 Maeda MC305CRM(E) Load Charts load Outriggers at Maximum position 5.945m boom 8.145m boom m boom m boom < < load Outriggers at Intermediate position 5.945m boom 8.145m boom m boom m boom < < load Outriggers at Minimum position 5.945m boom 8.145m boom m boom m boom < < The Total Rated Load Charts are based on the actual working radius including boom defl ection. The weight of the hook (standard 4 fall - 30kg) must be included as part of the load shown in the Total Rated Load Charts. When using two fall or single fall hooks, use the appropriate four fall Total Rated Load Chart above but with a maximum load of: Two Fall kg, Single Fall - 750kg.

7 Maeda MC405CRM(E) Technical specifi cations Offering the best balance of power and design Pick & Carry Duty (300kg maximum) Two Travel Speeds Programmable Moment Limiter 1130kg at 5.0m radius on 16.43m boom Specification MC405CRM(E) Crane capacity 3.83t x 2.7m Max. working radius 16m Max. lifting height 16.8m Hook speed 10m / min. (18.0m / min.) (4 falls, 4th layer) Single line speed 40m / min. (72.0m / min.) (4th layer) Hoist rope IWRC 6 x WS(26) 8mm x 95m Telescopic system Boom length Telescoping speed Boom type 4.735m m 11.7m / 54.2 sec (41.3sec) Fully automatic 5 section pentagonal telescopic boom Rubber Tracks Hydrostatic Transmission Centralised Controls Boom hoist system Hoist angle / speed Slew system Slew angle / speed Outrigger system Maximum extended dimensions 0-80 / 24.5 sec (17.0 sec) 360 / 2.1 rpm (2.5 rpm) Extension and set up by direct acting hyraulic cylinders (Length) 5786mm x (Front) 5118mm x (Rear) 5520mm 4 Fall / 2 Fall Hook Block Automatic Hook Stowage System Tilt Sensor/Alarm Traction system Engine Drive Travel speed Gradability Crawler length x width Ground pressure Rated output Starting medthod Fuel / Fuel tank capacity Hydraulic motor driven, stepless speed changer km/h mm x 320mm 49.0 (0.50) kpa (kgf/cm 2 ) Yanmar 3TNV88-PMB 3 cylinder water cooled diesel 21.8kw/2400min-1 (29.6PS/2400rpm) Electric Diesel/60L Powerful Winch with Hydraulic Disc Brake Electric Motor MC405CRME Size Totally enclosed fan-cooled motor 7.5kw, 4P 380V Two Speed Winch Remote control system Cable remote controller, micro-speed mode, load display for transmitter, outrigger operation Fully Automatic Pentagonal Section Boom Cable Remote Controller Dimensions Standard equipment Length x Width x Height Weight MC405CRM Weight MC405CRME 4980mm x 1380mm x 1980mm 5600kg 5750kg Overwind protection, load indicator, hydraulic safety valve, wire rope latch, level, machine body inclination alarm, EMO switch, travel lock lever, outrigger interlock device, moment limiter, rotary lamp, 4-fall / 2-fall hook block. Optional equipment Radio remote control, white rubber tracks, single fall hook, searcher hook, fl y-jib.

8 Maeda MC405CRM(E) Dimensions Overall Size Outrigger Spread Dimensions Range Chart Lifting height (m) The Range Chart does not take into account boom defl ection under load. The maximum reach below ground level is: Four Fall Two Fall Single Fall 20.50m 41.00m 82.00m

9 Maeda MC405CRM(E) Load Charts load (4 falls) Outriggers at Maximum position 4.735m/7.695m boom m boom m boom m boom < load (4 falls) Outriggers at Intermediate position 4.735m/7.695m boom m boom m boom m boom < load (4 falls) Outriggers at Minimum position 4.735m/7.695m boom m boom m boom m boom < The Total Rated Load Charts are based on the actual working radius including boom defl ection. The weight of the hook (standard 4 fall - 30kg) must be included as part of the load shown in the Total Rated Load Charts. When using two fall or single fall hooks, use the appropriate four fall Total Rated Load Chart above but with a maximum load of: Two Fall kg, Single Fall - 970kg.

10 Maeda LC785 Technical specifi cations Offering the best balance of power and design 2000kg Pick & Carry Duty Two Travel Speeds Programmable Moment Limiter Steel Tracks Hydrostatic Transmission Fully Enclosed Air Conditioned Cab 4 Fall / 2 Fall Hook Block Tilt Sensor/Alarm Powerful Winch with Hydraulic Disc Brake Two Speed Winch Specification LC785 Crane capacity 4.9 t x 2.1m Max. working radius 14.52m Max. lifting height 16.35m Hook speed Two speed 27 / 39m / min. (4 falls, 4th layer) Single line speed Two speed 108 / 156m / min. (4th layer) Hoist rope IWRC 6 x Fi (29) 10mm x 115m Telescopic system Boom length Telescoping speed Boom type 4.63m m 11m / 24.5 sec Fully automatic 5 section pentagonal telescopic boom Boom hoist system Slew system Drive Traction speed Engine Hoist angle / speed Slew angle / speed Travel speed low Travel speed high Gradability Crawler length x width Ground pressure Rated output Fuel / Fuel tank capacity - 2 to 80º (12.5 sec.) 360º continuous / 2.4 rpm Both sides independent steering control, hydraulic piston motor with in-built automatic brake, planet reduction gears, sprocket crawler km/h km/h 20 1,870mm x 450mm 46.8 kpa / cm² (0.48 kg / cm²) Komatsu S4D95LE-3-A 4 cylinder diesel, water cooled, direct injection 40.5 Kw (55PS) / 1850rpm Diesel / 141 L Fully Automatic Pentagonal Section Boom Dimensions Standard equipment Length x Width x Height Weight 5005mm x 2350mm x 2685mm 9700kg Safe load indicator, steel tracks, 4-fall / 2-fall hook block, working light, hour-meter and inclination alarm. Minimal Tail Swing Optional equipment Single fall hook, rubber pads (400kg), fl y-jib.

11 Maeda LC785 Dimensions 5005mm Overall Size 2685mm 450mm 450mm 2840mm 2350mm 15.63m boom 12.88m boom 10.13m boom 7.38m boom 4.63m boom 0 Range Chart º 70º 60º 50º 16.35m 40º 30º 20º º 4 2 0º m 6.27m 9.02m 11.77m 14.52m Lifting height above ground level (m) The Range Chart does not take into account boom defl ection under load. The maximum reach below ground level is: Four Fall Two Fall Single Fall 25.10m 51.30m m

12 Maeda LC785 Load Charts load 4.63m boom 7.38m boom 10.13m boom 12.88m boom 15.63m boom Pick & Carry duties 4.63m boom 7.38m boom 10.13m boom Pick & Carry duties are available at boom lengths up to metres. The Total Rated Load Charts are based on the actual working radius including boom defl ection. The weight of the hook (standard 4 fall - 90kg) must be included as part of the load shown in the Total Rated Load Charts. When using two fall or single fall hooks, use the appropriate four fall Total Rated Load Chart above but with a maximum load of: Two Fall kg, Single Fall kg