CURRIES Technical Manual FireRatedProducts Section. Revised September, 2017

Transcription

1 URRIES Technical Manual FireRatedProducts Section Revised September, 017

2 i Index September, 017 DESRIPTION PGE(S) 18 Gauge Three Sided Fire Door Frame nchors Drywall (-Type) Frame Drywall Frame ompression nchor Security... 1 ullet Resistant Window Frames Field Splice Frames Fire Door Limitations and Requirements stragals... 1 learances losing Devices.... Dutch Doors.... Exit Devices... Gasketing/Edge Seals... General Glass/Glazing... Hinges... Labels.... Locks.... Louvers.... Modifications... Pairs of doors.... Protection Plates/Plant ons.... Smoke and Draft ontrol.... Temperature Doors.... Vision Light Requirements.... Fire Door, Transom/Sidelight, and Window Frame Stops Fire Protective Window Frame 0 minute Without Hose Stream KD 0 minute Without Hose Stream... 6 KD 45 minute minute minute - Masonry Walls Only minute - Drywall Walls minute - Drywall Walls with Non ombustible Sill KD 60 minute with Firelite Glass Fire Resistive Fire Window Frame (E11) 60 Minute with ontraflam Minute with ontraflam Structure Minute with ontraflam Minute with ontraflam Minute with ontraflam Structure Minute with ontraflam Fire Protective Window Frame ow Window Fire Protective Four Sided Fire Door Frame Fire Protective Frame Stop Height Extenders for Glass Lites and Transom/Sidelights... 57

3 ii Index September, 017 DESRIPTION PGE(S) Glazing harts Door and Frame Frame Panel Fire Protective Half Sidelights KD Fire Door Frame apabilities hart Maximum Label Door learances Multiple Opening Frames.... Panel Doors Stop Extensions for Glass Lites and Transom/Sidelights Three Sided Fire Door Frame Masonry 180 minute Drywall 0 minute minute Oversized Doors and Frames (UL) minute Oversized Doors and Frames (WH) Transom Frame Wood Transom Panel Rabbeted Wood Door & Transom Panel Without Transom ar (Steel Panel) Three sided fire door frame with transom Fire Protective Transom/Sidelight Frame 0 minute without Hose Stream minute - Drywall minute - Masonry minute minute - Drywall Walls Only minute - Masonry Walls Only Fire Resistive Transom/Sidelight Frame 60 Minute with ontraflam Minute with ontraflam Structure Minute Door Installation Detail Minute with ontraflam Minute with ontraflam Minute with Door ontraflam Structure Minute Door Installation Detail Minute Door Installation Detail Fire Door apabilities hart

4 1 Fire Door Limitations and Requirements February, 016 URRIES fire rated doors and frames are listed and labeled by Underwriters Laboratories, LL (UL) and Intertek-Warnock Hersey (Intertek). Doors and frames were tested in accordance with UL, UL 10, UL 10, STM E074, STM E15, NFP 5, NFP 57, U 7-, N4S-104 and N4S-106. STM E15 and STM E074 have been withdrawn and are considered obsolete although included as a reference standard in some job specifications. U 7- has largely been replaced by the International uilding ode (I). The fire rated labels that we apply to doors and frames signify compliance with both Neutral and Positive Pressure test requirements. GENERL a) Only listed doors may be used in a fire rated opening. b) Every labeled swinging fire door must have a self latching device. c) pproved hardware and components are listed in the Underwriters Laboratories UL online ertifications Directory or ITS/Warnock Hersey Directory of Listed Products. d) Labeled doors may be stainless steel. e) Viewers must be listed. onsult manufacturers listing for limitations. f) The rating for the opening is the rating of the lowest rated component. g) Embossed panel doors have the same fire rating as 707 doors. h) NFP 80 shall be followed for installation. STRGLS stragals may not be used at any hourly ratings for standard pairs of any door model with Vertical Rod Exit Devices on both leaves. Pairs of doors with rim or mortise exit devices that latch into a hardware or hollow metal mullion can be labeled to the same capabilities as two () single doors (check with uthority Having Jurisdiction (HJ) prior to using this capability to verify acceptance). stragals, when required for fire protection, must be a steel overlapping design in accordance with our procedures. Split stragals and Meeting Stile Gasketing that are fire rated up to 180 minutes cannot be used on URRIES fire rated doors that require a steel overlapping astragal for fire protection. These fire rated Split stragals and Meeting Stile Gaskets may be used on URRIES fire rated doors that don t require a steel overlapping astragal for fire protection. stragals shall be attached with welds or screws and project /4 minimum beyond the lock edge of the door. STRGL USGE REQUIREMENTS The objective of this specification is to summarize the use of steel overlapping astragals on the meeting edge of standard swing and double egress pairs. Most of the requirements are applicable to fire rated product limitations. Underwriters Laboratories and Intertek capabilities that are different are listed separately. Underwriters Laboratories: stragals (1ga. flat or 14 ga. Z-shaped) are optional on all Standard Pairs and Double Egress Model 707 doors with a fire rating up to and including 1-1/ hours. stragals are required on all Model 707 doors with a fire rating of hours. stragals are optional on all Standard Pairs and Double Egress Model 747 doors with a fire rating up to and including hours. stragals are required on all Model 77 doors at all hourly ratings and opening sizes. Intertek (Warnock Hersey): stragals are optional on the following doors up to hours: Standard Pairs: Model Maximum opening size (Polystyrene and honeycomb cores) Model Maximum opting size Double Egress: Model Maximum opening size Model Maximum opening size stragals are optional on Model 77 doors up to and including 1-1/ hours. stragals are required on Model 77 doors when the hourly rating exceeds 1-1/ hours. LERNES a) The maximum clearance between the door and frame and between meeting edges of doors swinging in pairs is 1/8 inch (re: NFP80). Refer to URRIES Tech Data sections for design clearances on URRIES doors. b) The maximum clearances under the bottom of a fire door shall be /4 (1 mm) per NFP 80. NOTE: Doors with vertical rod devices may have bottom latches that may not engage the strike if maximum allowed clearances are used. hardware coordinator must be used to ensure proper closing when astragals are used on pairs of doors equipped with Vertical Rod Exit Device on one leaf and a Mortise Exit Device on the other leaf.

5 Fire Door Limitations and Requirements January, 014 LOSING DEVIES a) closing device shall be installed on every fire door. b) loser reinforcements are furnished as standard on URRIES fire rated doors. c) If the closer is installed with sex bolts, the closer reinforcement may be omitted on fire rated doors. d) Spring hinges may be used instead of a closer and a closer reinforcing. t least two spring hinges are required per door leaf. e) The closer may be omitted on the inactive leaf of pairs of doors to mechanical equipment rooms (re: NFP80). f) Overhead stops may be used if they do not inhibit the door from closing and latching. g) If an astragal or projecting latch bolt prevents the inactive door from closing and latching before the active door, a coordinating device shall be used. coordinating device is not required where each door leaf of a pair of doors closes and latches independently of each other. h) Door holder/release devices are permitted when acceptable to the uthority Having Jurisdiction.These are fail-safe devices, controlled by a detection device to release the door in the event of fire (re: NFP80). DUTH DOORS a) The upper and lower leaf may latch into the frame or the upper leaf may latch in lower leaf which latches into the frame. b) The top leaf must be equipped with a closing device and a horizontal astragal that brings the bottom leaf closed c) Fire-rated dutch doors must have a horizontal astragal attached to the bottom of the top leaf for all hourly ratings. EXIT DEVIES a) URRIES labeled fire exit doors may be prepared for any listed fire exit hardware device. b) The door size must must not exceed the maximum door size listed for the individual hardware manufacturers devices. c) Doors that are reinforced for fire exit hardware must bear a label which states Fire Door to be equipped with Fire Exit Hardware. d) Fire Exit Hardware may be applied to doors that are not reinforced for such hardware by using sex bolts or through bolts. These doors may not bear the label Fire Door to be Equipped with Fire Exit Hardware. e) Vertical rod exit devices may not be used on a single door (this does not include less bottom rod devices that have a mortise lock.) GSKETING/EDGE SELS a) Only listed gasketing material may be used, consult the U.L. ertifications (online) Directory Intertek Listed Product Directories. b) Smoke and draft control assemblies must employ gaskets listed for smoke and draft control. c) URRIES fire rated doors do not require the use of edge seal systems (intumescents). GLSS/GLZING a) See glazing capability charts for type, size, and rating of glass. HINGES a) Doors up to 60 inches in height require two leaf type hinge. n additional hinge must be used for each additional 0 inches of height or fraction thereof (NFP80). b) URRIES fire doors over 6 inches in height may be prepared for standard weight hinges. c) Listed continuous hinges, pivots, or electric hinges may be used with URRIES fire rated doors. LELS a) Fire labels on URRIES doors are metal. Metal labels may be attached with drive screws or steel pop rivets. b) Labels may be applied only at authorized locations. c) field inspection is required for a label to be applied at a jobsite. LOKS a) The door size used must not exceed the maximum door size listed for the individual hardware manufacturers devices. b) Refer to the hardware manufacturer s listing to determine capability to supply single point locks for doors over 8 feet in height. c) Latch Throw Requirements 607 & 707 Single: 1/ inch minimum latch throw 607 & 707 Pairs: 707 Pairs: 5/8 inch minimum latch throw on pairs to 8 feet in height. /4 inch minimum latch throw on pairs to 10 feet in height. 77 Single: 1/ inch minimum latch throw 77 Pairs: 5/8 inch minimum latch throw 747 & 847 Single: 1/ inch minimum latch throw 747 & 847 pairs: 5/8 inch minimum latch throw 747 doors may also be prepared for two and three point latching devices.

6 Fire Door Limitations and Requirements November, 015 LOKS (continued) d) Dead bolts may not be used on doors which are in a means of egress. Locks with dead bolts that are interconnected with latch bolts and retract simultaneously when the latch bolt is retracted may be used on fire doors within a means of egress. e) Dead bolts may be used in addition to an active latch bolt on doors that are not in a means of egress, or as otherwise permitted by the uthority Having Jurisdiction. LOUVERS a) ny listed automatic fusible link louver may be used in URRIES labeled doors. b) Maximum rating for louvers is 0 minutes. c) Maximum listed louver size is 4 x 4 inches. d) Louvers may not be installed in the upper half of a fire door. e) Louvers may not be installed in 0 minute doors. MODIFITIONS ny retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and URRIES makes no representations or warranties concerning what such impact may be in any specific situation. When retrofitting any portion of an existing fire rated opening, or specifying and installing a new fire-rated opening, please consult with a code specialist or local code official (uthority Having Jurisdiction) to ensure compliance with all applicable codes and ratings. PIRS OF DOORS a) The inactive leaf of pairs of doors may be provided with self-latching top and bottom bolts or automatic flush bolts or labeled two point latches. Manual bolts either mortise or surface may be used on doors to rooms not normally occupied by humans. b) Double egress doors are intended to be provided with vertical rod exit devices (concealed or surface mounted). c) Open back strikes may be used on pairs of 707 or 747 doors to a maximum of 8 0 high, maximum height for 607 doors is 7 0 high. d) Two doors in the same frame separated by a hollow metal mullion are treated as two single doors. SMOKE ND DRFT ONTROL a) ll components used in a Smoke and Draft ontrol assembly must pass a 0 minute without hose stream fire test. b) Only gaskets listed for smoke and draft control may be used for smoke and draft control assemblies. c) The gaskets used for a smoke and draft control assembly must be listed for the type of door installed in the frame, i.e. hollow metal or wood. d) Wood doors used in a smoke and draft assembly that do not have intumescent imbedded in the door edge may require an edge seal (intumescent) and a smoke and draft control qualified gasket to be installed in the door frame. TEMPERTURE RISE DOORS a) The L77 series door may be used in 50 and 450 temperature rise applications. b) steel overlapping astragal is required on all fire-rated pairs of 77 doors. c) The 747 temperature rise door is available at a 450 rating only. VISION LIGHT REQUIREMENTS a) No glass should be used in exterior doors subject to a severe fire exposure. b) ny listed fire door vision light kit may be used in URRIES labeled doors. Vision kits should be listed for use in the type of door construction they are installed in. c) URRIES vision light kits may be used in URRIES doors only. d) Minimum stile between visible glass and the edge of door is 6 inches, the minimum distance between two vision light kits is 6 from visible glass to visible glass. e) NFP 80 allows vision lite kits up to 100 sq. inches in 50 and 450 temp. rise applications. uthority Having Jurisdiction may allow use of specialty glazing (see glazing chart for approved glazing) over 100 sq. inches. PROTETION PLTES/PLNT ONS a) Protection plates or kick plates may be a maximum of 46 wide x 6 high and may be attached to both faces of a door; protection plates may not be thicker than the door face skin gauge. NFP 80 states that labeling is not required on protection plates less than 16. Field installed plates must be labeled and installed in accordance with the protection plate manufacturer s listing. The protection plate manufacturer should advise size and installation limitations. Protection plates are listed under UL ategory code GVUX. b) Plant-ons, decorative moldings, or cladding may not be used on URRIES fire doors.

7 4 Notes

8 5 Fire Door apabilities hart ugust, 016 Series Skin Gauges Door Thickness Inches (mm) L607 0 or 18 1 /4 (44) L707 0 or 18 1 /8 (5) L707 0, 18, 16 1 /4 (44) L /4 (44) L77 () 18 or 16 1 /4 (44) L or 16 1 /4 (44) L747 TR () 18 or 16 1 /4 (44) L /4 (44) TYPE RTING MXIMUM OPENING SIZE 180 min. SINGLE 0 min. 60 min FLUSH (11x14) (1016x184) (11x48) (11x48) (11x48) (11x048) (11x048) 45 min. 0 min. PIR FLUSH DL EGRESS FLUSH 180 min. 0 min. 60 min. 45 min. 0 min. 180 min. 0 min. 60 min. 45 min. 0 min (48x14) 6070 (18x14) 8080 (48x48) 6080 (18x48) 8080 (48x48) 6080 (18x48) 8080 (48x48) 8080 (48x48) (48x048) (48x048) (48x048) (48x048) 4080 (11x48) 8080 (48x48) 8080 (48x48) L or 14 1 /4 (44) 4080 (11x48) 8080 (48x48) L777 18,16,14 1-/4 (44) 4080 (11x48) 8080 (48x48) 800 (48x74) max 0 min. L777E 18 or 16 1-/4 (44) 4080 (11x48) UL only, WH max. 0 minutes 8080 (48x48) UL only, WH max. 0 minutes L /4 (44) 4080 (11x48) 8080 (48x48) 8080 (48x48) L (51) 4080 (11x48) SINGLE LOUVER 0 min. 45 min (11x14) 4080 (11x48) 4080 (11x48) (11x048) (11x048) 4080 (11x48) 4080 (11x48) 4080 (11x48) 4080 (11x48) 4080 (11x48) PIR LOUVER 0 min. 45 min (48x14) 8080 (48x48) 8080 (48x48) (48x048) (48x048) 8080 (48x48) 8080 (48x48) 8080 (48x48) 8080 (48x48) DUTH DOOR FLUSH SINGLE EMOSSED PNEL PIR EMOSSED PNEL SINGLE FULL GLSS PIR FULL GLSS 180 min. 0 min. 60 min. 45 min. 0 min. 180 min. 0 min. 45 min. 0 min. 180 min. 0 min. 45 min. 0 min. 0 min. without hose stream 0 min. without hose stream 470 (1016x14) (1067x14) 6870 (0x14) (0x14) 4080 (11x48) 8080 (48x48) 4080 (11x48) 8080 (48x48) 87 (1118X184) 4080 (11x48) 8080 (48x48) 87 (1118X184) 4080 (11x48) 8080 (48x48) 470 (1016x14) 4080 (11x48) 8080 (48x48) 4080 (11x48) 8080 (48x48) NOTES: 1) SEE DOOR GLZING SPEIFITIONS FOR GLZING REQUIREMENTS ) 180, 0, 60, 45 MIN. LELS ONLY ) MINERL ORE PNEL 4) 18 GUGE SINGLE PNEL DOOR 0 min. 45 min. 0 min (11x48) 4080 (11x48) 4080 (11x48) 4080 (11x48) NOTES: SEE PGE FOR MORE INFORMTION ON PNEL DOORS

9 6 Panel Doors February, MINUTE MXIMUM RTING. UL ONLY TYPIL FE TYPES 6 (15.4) MIN. 6 (15.4) MIN. 6 (15.4) MIN. * * * * GLSS 6 (15.4) MIN. * * 6 (15.4) MIN. 6 MINIMUM STILE ND RIL 1/ (1.7) REF. 1/ (1.7) MIN. URRIES FIRE RTED 1/ PNEL 18 G. (1.) ONLY /4 (1.1) MIN. 100% SILIONE ULK 18 G. (1.) OR 16 G. (1.5) SKINS SETION - #6 OVL HED METL MX.O.. MX.FROM EH END MXIMUM VISILE WIDTH 6 MXIMUM VISILE HEIGHT 6 MXIMUM RE PER PNEL 16 SQ. IN. MXIMUM PNEL RE PER DOOR 5 SQ. IN. 1-/4 (44.5)

10 7 Maximum Label Door learances pril, 00 SINGLE 1/8 () PIR /4 (1)* 1/8 () 1/8 () 1/8 () 1/8 () 1/8 () DOULE EGRESS 1/8 () 1/8 () 1/8 () REFERENE: MXIMUM LERNES S PULISHED IN N.F.P.. 80; FIRE DOORS ND WINDOWS. *URRIES STNDRD UNDERUT IS 5/8 (16)

11 8 KD Fire Door Frame apabilities hart ugust, 014 HOUR RTING 180 ( HOUR) MSONRY WLLS ONLY 0 (1-1/ HOUR) 45 (/4 HOUR) 0 (0 MINUTE) PROFILE TYPE 1 FE FRME M 1-1/4-4 FE FRME M M MT L GUGE JM DEPTH SIZES ( MIN MX. 4 MIN MX. 14 (10) - (56) (10) - (56) (1, ( (1, ( G ( MG DEM WM WM WG WG 14-1/4 ( MIN MX. (8) - (56) -1/4 ( MIN MX. (8) - (56) -1/4 (4 MIN MX. -1/4 ( MIN MX. (8) - (56) ( (8) - (56) NOT VILLE NOT VILLE NOT VILLE -1/4 ( MIN MX. (8) - (56)( 4-/4 MIN MX. (11) - (56) 5-1/4 MIN MX (1) - (56) 5-1/4 MIN MX. (1) - (56) 4-1/8 MIN MX. (105) - (56) 4-1/8 MIN MX. (105) - (56) W (1 16 NOT VILLE -1/4 ( MIN MX. (8) - (56) 4-5/8 MIN MX. (117) - (56) -1/4 ( MIN MX. (8) - (56) -1/4 ( MIN MX. (8) - (56) 4-/4 MIN MX. (11) - (56) 5-1/4 MIN MX. (1) - (56) 5-1/4 MIN MX. (1) - (56) 4-1/8 MIN MX. (105) - (56) 4-1/8 MIN MX. (105) - (56) 4-5/8 MIN MX. (118) - (56) 4 MIN MX. (10) - (56) -1/4 ( MIN MX. (8) - (56) -1/4 ( MIN MX. (8) - (56) -1/4 ( MIN MX. (8) - (56) 4-5/8 MIN MX. (117) - (56) -1/4 ( MIN MX. (8) - (56) -1/4 ( MIN MX. (8) - (56) 4-/4 MIN MX. (11) - (56) 5-1/4 MIN MX. (1) - (56) 5-1/4 MIN MX. (1) - (56) 4-1/8 MIN MX. (105) - (56) 4-1/8 MIN MX. (105) - (56) 4-5/8 MIN MX. (118) - (56) 4 MIN MX. (10) - (56) -1/4 ( MIN MX. (8) - (56) -1/4 ( MIN MX. (8) - (56) -1/4 ( MIN MX (8) - (56) 4-5/8 MIN MX. (117) - (56) -1/4 ( MIN MX. (8) - (56) -1/4 MIN MX. (8) - (56) 4-/4 MIN MX. (11) - (56) 5-1/4 MIN MX. (1) - (56) 5-1/4 MIN MX. (1) - (56) 4-1/8 MIN MX. (105) - (56) 4-1/8 MIN MX. (105) - (56) 4-5/8 MIN MX. (118) - (56) (1 OMPRESSION NHOR ( ONLY MSONRY WLLS WITH PPROVED ORNER LIP ( -1/4-4 JM DEPTH FOR 1-/8 DOORS ONLY (4 MSONRY WLLS ONLY (5 18 GUGE VILLE - SEE FOLLOWING PGES (6 14 G. VILLE IN FE ONLY (7 SME PROFILE FOR HED & JM

12 KD Fire Door Frame apabilities hart December, 01 HOUR RTING PROFILE TYPE 1 FE FRME M 1-1/4-4 FE FRME M M 180 ( HOUR) MSONRY WLLS ONLY NEUTRL ND POSITIVE PRESSURE 0 (1-1/ HOUR) MT L GUGE OPENING SIZES ( SINGLE: 4 0 X 8 0 PIRS: 8 0 X 7 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 (1 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 8 0 PIRS: 8 0 X 7 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X (/4 HOUR) SINGLE: 4 0 X 8 0 PIRS: 8 0 X 7 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X (0 MINUTE) SINGLE: 4 0 X 8 0 PIRS: 8 0 X 7 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 (1, (4 16 NOT VILLE SINGLE: 6 X 7 0 SINGLE: 6 X 7 0 SINGLE: 6 X 7 0 (1 16 NOT VILLE 16 G ( MG DEM WM WM WG WG SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 ( SINGLE: 4 0 X 0 PIRS: 8 0 X 7 - OR X 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 0 PIRS: 8 0 X 7 - OR X 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 0 PIRS: 8 0 X 7 - OR X 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 PIRS: 8 0 X 10 0 ( PIRS: 8 0 X 10 0 PIRS: 8 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 ( SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 ( W (1 16 NOT VILLE SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 0 PIRS: 8 0 X 7 - OR X 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 0 PIRS: 8 0 X 7 - OR X 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 10 0 PIRS: 8 0 X 10 0 SINGLE: 4 0 X 0 PIRS: 8 0 X 7 - OR X 0 (1 OMPRESSION NHOR ( ONLY MSONRY WLLS WITH PPROVED ORNER LIP ( 18 GUGE VILLE - SEE FOLLOWING PGES (4 1-/8 DOORS ONLY (5 SME PROFILE FOR HED & JM

13 10 18 Gauge Three Sided Fire Door Frame ugust, MINUTE MXIMUM RTING GENERL NOTES: 1) TO SUIT DOOR THIKNESS ) VRIES ) PROFILE VRILE 4) /8 (10) MIN. /4 (1) MX. 5) /8 (10) MIN. 1-/8 (5) 6) 1-1/4 ()* 4 (10) MX. JM 6 (15) MX. HED 6) 5/8 MIN. (16) 1) ) 4) MSONRY DRYWLL SINGLE RET: 4-1/4 (108) MIN. 14 (56) MX. * DOULE RET: 4-1/8 (105) MIN. 14 (56) MX. 5) )

14 11 18 Gauge Three Sided Fire Door Frame pril, 00 0 MINUTE MXIMUM RTING - DRYWLL WLLS (WRNOK HERSEY LISTING ONLY) MXIMUM FRME SIZES MSONRY, DRYWLL: WLL ONSTRUTION: FRME ORNER ONSTRUTION: NHORS: MTERIL: SINGLE 4 0 (11) W X 8 0 (48) H PIRS 8 0 (48) W X 8 0 (48) H DRYWLL OR MSONRY WLLS KD, FE WELD, OR ONTINUOUS WELD NY LISTED WELD-IN OR SLIP-IN DRYWLL OR MSONRY TYPE. NHOR MY E USED IN THIS FRME. (OMPRESSION NHORS NOT LLOWED) 18 G. (1.) MIN. OLD ROLLED OR GLVNIZED STEEL HRDWRE RESTRITIONS ) HINGES: ) LOSERS: STEEL (LL ERING - OIL LIGHT USHING) TYPE, POKET PIVOT TYPE, STNDRD PIVOT TYPE, NHOR TYPE, ND ONTINUOUS TYPE. LOSERS RE REQUIRED ON LL FRMES WHIH RE TO E FIRE LELED, REGRDLESS OF THE HOURLY RTING. IF LEL PPROVED REINFOREMENT IS NOT PROVIDED, THE LOSER MUST E THROUGH -OLTED TO THE FRME. IN LIEU OF LOSER, SPRING HINGES MUST E USED. ) STRIKES: STNDRD STRIKES FOR VRIOUS TYPES OF LISTED HRDWRE MY E USED. D) HRDWRE MULLION: IT IS PERMISSILE TO USE LISTED HRDWRE MULLION IN PIR ONFIGURTION. NOTE: NY HRDWRE WHIH IS TO E USED ON FIRE RTED DOORS ND FRMES SHOULD E ONFIRMED FOR LEL PPROVL USING THE LTEST EDITION OF THE U.L. FIRE RESTRITIVE DIRETORY VOL., OR ITS/WHI DIRETORY OF LISTED PRODUTS. FE WELDING OMPLETELY SSEMLED ND INSTLLED KD FRMES IN THE FIELD IS N EPTLE PRTIE, ONTT FTORY FOR DETILS.

15 1 Three Sided Fire Door Frame February, MINUTE MXIMUM RTING - MSONRY WLLS 0 MINUTE MXIMUM RTING - DRYWLL WLLS GENERL NOTES: 1 4 TO SUIT DOOR THIKNESS VRIES PROFILE VRILE /8 (10) MIN. 1 5/8 MIN. (16) 5 /4 (1) MX. /8 (10) MIN. 1-/8 (5) 6 MSONRY DRYWLL 6 1-1/4 ()* 4 (10) MX. JM 8 (04)1 MX. HED 1 5/8 MIN. (16) 4 SINGLE RET: -1/4 (1) MIN. 14 (56) MX. * DOULE RET: 4 (10) MIN. 14 (56) MX. 5-1/8 (54) 1-/16 (40) MIN. /8 () 1-/8 (5) MIN. 4 (10) MX. DOULE EGRESS 4-/4 (11) MIN. 14 (56) MX. ompression anchors not available in label construction * -1/4 to 4 jamb depth for 1-/8 door only. 1) Heads with greater than 4 face are UL label only URRISEL SINGLE RET: 4-1/8 (105) MIN. 14 (56) MX. DOULE RET: 5-1/4 (1) MIN. 14 (56) MX. 5

16 1 Three Sided Fire Door Frame June, MINUTE MXIMUM RTING - MSONRY WLLS 0 MINUTE MXIMUM RTING - DRYWLL WLLS MXIMUM FRME SIZES MSONRY, DRYWLL: DOULE EGRESS: URRISEL: SINGLE 4 0 (11) W X 10 0 (048) H PIRS 8 0 (48) W X 10 0 (048) H PIRS ONLY 8 0 (48) W X 10 0 (048) H OMPRESSION NHOR NOT VILLE IN LEL ONSTRUTION SINGLE 4 0 (11) W X 10 0 (048) H PIRS 8 0 (48) W X 10 0 (048) H WLL ONSTRUTION: DRYWLL OR MSONRY WLLS FRME ORNER ONSTRUTION: NHORS: MTERIL: MULLIONS: KD, FE WELD, OR ONTINUOUS WELD NY LISTED WELD-IN OR SLIP-IN DRYWLL OR MSONRY TYPE NHOR MY E USED IN THIS FRME. 16 G. (1.5) MIN. 1 G. (.6) MX. OLD ROLLED OR GLVNIZED STEEL WELDED OR REMOVLE HOLLOW METL MULLIONS RE PERMITTED. HRDWRE RESTRITIONS ) HINGES: ) LOSERS: STEEL (LL ERING - OIL LIGHT USHING) TYPE, POKET PIVOT TYPE, STNDRD PIVOT TYPE, NHOR TYPE, ND ONTINUOUS TYPE. LOSERS RE REQUIRED ON LL FRMES WHIH RE TO E FIRE LELED, REGRDLESS OF THE HOURLY RTING. IF LEL PPROVED REINFOREMENT IS NOT PROVIDED, THE LOSER MUST E THROUGH -OLTED TO THE FRME. IN LIEU OF LOSER, SPRING HINGES MUST E USED. ) STRIKES: STNDRD STRIKES FOR VRIOUS TYPES OF LISTED HRDWRE MY E USED. D) HRDWRE MULLION: IT IS PERMISSILE TO USE LISTED HRDWRE MULLION IN PIR ONFIGURTION. NOTE: NY HRDWRE WHIH IS TO E USED ON FIRE RTED DOORS ND FRMES SHOULD E ONFIRMED FOR LEL PPROVL USING THE LTEST EDITION OF THE U.L. FIRE RESTRITIVE DIRETORY VOL., OR ITS/WHI DIRETORY OF LISTED PRODUTS. FE WELDING OMPLETELY SSEMLED ND INSTLLED KD FRMES IN THE FIELD IS N EPTLE PRTIE, ONTT FTORY FOR DETILS.

17 14 Three Sided Fire Door Frame ugust, FE DOOR FRME MSONRY WLL ONSTRUTION 180 MINUTE MXIMUM FIRE RTING SIZE: SINGLE 4 0 (11) W X 8 0 (48) H PIR 8 0 (48) W X 7 0 (14) H WLL ONSTRUTION: MSONRY FRME ONSTRUTION: KD* FE WELD OR ONTINUOUS WELD TO SUIT DOOR THIKNESS PROFILE VRILE 1 (5) MIN. 4 (10) MX. JM 8 (04) MX. HED 4-1/8 (105) MIN. 14 (56) MX. /8 (10) MIN. 1-/8 (5) MX. 1) WELDED ND REMOVLE MULLIONS MY E USED WITH THIS FRME. ) NY LISTED WELD IN OR SLIP IN MSONRY NHOR MY E USED IN THIS FRME. ) HEDS WITH GRETER THN 4 FE RE UL LEL ONLY.

18 15 Transom Frame (Wood Transom Panel) ugust, 014 WOOD TRNSOM PNEL 0 MINUTE MXIMUM RTING FRME SIZE: 4 0 (11) W X 11 0 (5) SINGLE SWING WLL ONSTRUTION: MSONRY DRYWLL FRME ONSTRUTION: ONTINUOUS WELD TRNSOM PNEL: NY LISTED WOOD TRNSOM PNEL MX. PNEL SIZE: SED ON WOOD DOOR MNUFTURER S LISTING. 1-1/ HOUR MX. LEL RTING MX. DOOR SIZE: NY LELED DOOR TO SUIT DOOR THIKNESS 5/8 MIN. (16) PROFILE VRILE (51) MIN. 4 (10) MX. 1 (5) FLT 1 G. (.6) REINFORING FOR TRNSOM PNEL SPRING OLTS. REINFORING IS INSTLLED IN JMS ON EH SIDE OF TRNSOM RE. 4 (10) MIN. 1 (05) MX. 1/4 (16) MIN. /4 (1) MX. NOTES: 1) THIS FRME IS ONSIDERED TRNSOM FRME ND MUST ER LEL WHIH STTES FIRE DOOR FRME WITH PNELS ) TTHMENT OF TRNSOM PNEL TO FRME IS Y USE OF SPRING OLTS THT RE PROVIDED WITH THE PNEL. (PNEL MY LSO E TTHED TO FRME Y OTHER MENS S LLOWED Y THE PNEL MNUFTURER S LISTING.) SPRING OLTS ENGGE IN TO REINFORED HOLES IN THE FRME. ) NY LISTED WELD IN OR SLIP IN MSONRY OR DRYWLL NHOR MY E USED IN THIS FRME. (OMPRESSION NHORS NOT LLOWED). 4) SEE GLZING HRTS ND TRNSOM/SIDELITE FRMES FOR DDITIONL PILITIES.

19 16 Transom Frame For Rabbeted Wood Door & Transom Panel ugust, MINUTE MXIMUM RTING. TO SUIT DOOR THIK- NESS 1/8 () MX. HED VRILE PROFILE FLT 1 G. (.6) RE- INFORING JM/HED 1 (5) MIN. (50) MIN. 4 (10) MX. PNEL LISTED WOOD RETED DOOR ND PNEL. 4-1/ (114) MIN. 14 (56) MX. /8 (10) MIN. 1-/8 (5) MX. 1/8 () MX. DOOR

20 17 Transom Frame For Rabbeted Wood Door & Transom Panel ugust, MINUTE MXIMUM RTING MSONRY, DRYWLL: 4 0 (11) X 10 0 (048) S KD 4 0 (11) X 11 0 (5) S WELDED MXIMUM DOOR HEIGHT: 8 0 (48) WLL ONSTRUTION: FRME ONSTRUTION: NHORS: MTERIL: TRNSOM PNEL: MSONRY OR DRYWLL KD, FE WELD, OR ONTINUOUS WELD NY LISTED WELD-IN OR SLIP-IN TYPE DRYWLL OR MSONRY NHORS MY E USED IN THIS FRME. (OMPRESSION NHORS NOT LLOWED). OLD ROLLED ND GLVNIZED STEEL 16 G. (1.5) MINIMUM TO 1 G. (.6) MXIMUM 1-/4 (44) THIKNESS MXIMUM SIZE: 4 0 (11) W X 4 0 (11) H MXIMUM LEL RTING: 1-1/ HOUR NOTE: 1) FLT 1 G. (.6) REINFORING FOR TRNSOM PNEL SPRING OLTS. REINFORING IS INSTLLED IN JMS ON EH SIDE OF TRNSOM PNEL. ) THIS FRME IS ONSIDERED TRNSOM FRME ND MUST ER LEL WHIH STTES: FIRE DOOR FRME WITH PNELS. ) TTHMENT OF TRNSOM PNEL TO FRME IS Y USE OF SPRING OLTS PROVIDED WITH THE PNEL. (PNEL MY E TTHED TO THE FRME Y OTHER MENS, S LLOWED Y THE PNEL MNUFTURERS LISTINGS.) SPRING OLTS ENGGE INTO REINFORED HOLES IN THE FRME. 4) ONTT WOOD DOOR & PNEL MNUFTURER FOR PNEL ND DOOR LIMITTIONS.

21 18 Transom Frame Without Transom ar (Fixed) ugust, MINUTE MXIMUM RTING. VRILE PROFILE JM/HED /8 (10) MIN. /4 (1) MX. 4 (10) MIN. 14 (56) MX. (50) MIN. 4 (10) MX. /8 (10) MIN. 1-/8 (5) MX. 1/8 () MX. 1/8 () MX. PNEL HED Fixed Panel Installation Options DOOR 1-1/ (8) MIN. 1 G. (.6) STRGL PPLIED TO PNEL WELD 1/ (1) LONG MIN. STNDRD SEE FRME SETION PGE 14 FOR REMOVLE PNEL DETILS OPTIONL OPTIONL THIS METHOD NNOT E USED ON MULLION SETIONS

22 1 Transom Frame Without Transom ar (Steel Panel) pril, MINUTE MXIMUM RTING - MSONRY WLLS 0 MINUTE MXIMUM RTING - DRYWLL WLLS MXIMUM FRME SIZE: WLL ONSTRUTION: FRME ONSTRUTION: NHORS: MTERIL: TRNSOM PNEL: SINGLE 4 0 (11) W X 10 0 (048) H PIR 8 0 (48) W X 10 0 (048) H MSONRY OR DRYWLL (DRYWLL WLL INSTLLTION LIMITED TO 0 MINUTES) KD, FE WELD, OR ONTINUOUS WELD NY LISTED WELD IN OR SLIP IN TYPE DRYWLL OR MSONRY NHORSMY E USED IN THIS FRME. (OMPRESSION NHORS NOT LLOWED). OLD ROLLED ND GLVNIZED STEEL 16 G. (1.5) MINIMUM TO 1 G. (.6) MXIMUM MUST E 747 ONSTRUTION. SINGLE: 4 0 (11) W X 0 (11) H MX. PIR: 8 0 (48) W X 0 (11) H STRGL: STRGL NOT REQUIRED ON SSEMLIES RTED 0. DOORS: MXIMUM DOOR LEF SIZE SINGLE & PIRS - 707: 4 0 (11) W X 10 0 (048) H SINGLE & PIRS - 747: 4 0 (11) W X 10 0 (048) H NOTE: 1) THIS FRME IS ONSIDERED TRNSOM FRME ND MUST ER LEL WHIH STTES: FIRE DOOR FRME WITH PNELS ND IS LIMITED TO THE SME RESTRITIONS S OTHER TRNSOM FRMES. ) SREWS ND WELDS FOR PNEL NHORING SHLL E T -1/ (64) FROM ENDS ND MXIMUM OF 1 (05) PRT ON TOP ND OTTOM EDGES ND 18 (457) PRT ON SIDES. PNEL SREWS SHLL E MINIMUM #10 SIZE.

23 0 ompression nchor (-Type) Slip-on Drywall Frame ugust, MINUTE MXIMUM FIRE RTING. SIZE: SINGLE: 4 0 (11) W X 0 (74) H PIR: 8 0 (48) W X 7 (184) 7 0 (14) W X 0 (74) H WLL ONSTRUTION: DRYWLL FRME ONSTRUTION: KD (WITH OMPRESSION NHOR SYSTEM) OUNTERSUNK SE NHOR HOLE IS STNDRD ON (51) FE FRMES, STRP TYPE SE NHOR OPTIONL. STRP TYPE SE NHOR OPTIONL ON (50.8) FE FRMES ND MUST E USED ON 1-1/ (8) ND 1-/4 (44) FE FRMES. 7/8 () MIN. TO SUIT DOOR THIKNESS 5/8 (16) 1-1/ (8), 1-/4 (44), ND (50.8) FES ONLY 1) 1/ (1) NOTE: 1) -1/4 (8) MIN (56) MX. FOR SINGLE OPENING FRMES TO 6 (1067) WIDE X 7 0 (14) HIGH 4-5/8 (118) MIN (56) MX. FOR SINGLE OPENING FRMES TO 4 0 (11) WIDE X 0 (74) HIGH ND DOULE OPENING FRMES TO 7 0 (14) WIDE X 0 HIGH OR 8 0 (0) WIDE X 7 (184) HIGH ) KD FRMES OVER 7 (16) UP TO 8 (48.4) REQUIRE ONE SEURITY NHOR PER JM (SEE NEXT PGE FOR DETILS). FRMES OVER 8 (48.4) UP TO (74.) REQUIRE THREE SEURITY NHOR IN EH JM. FRMES FOR PIRS OF DOORS OVER 7 (184.4) REQUIRE TWO SEURITY NHOR IN THE HED OF THE FRME. ONE EH 1 (04.8) FROM THE ENTERLINE OF THE FRME HED.

24 1 Security nchor pril, 00 NHOR PRT NUMER: P008-1/ (88.) VRIES 16 G. (1.4) OMPRESSION NHOR PER JM DEPTH 1-1/8 (8.6) 1-1/8 (8.6) SEURITY NHOR 45 (114) TYPIL OTTOM OF FRME Drywall Frame ompression nchor NHOR PRT NUMER: P006 5/8 (15.8) MXIMUM TRVEL -1/ (88.) OMPRESSION NHOR

25 Multiple Opening Frames ugust, 014 FRME ND DOOR ONFIGURTION MY VRY 0 MINUTE MXIMUM FIRE RTING. ELEVTION/SETIONS 8 (48.) 1 8 (860.8) NOTES: 1) MX. FOUR DOORS IN NY OMINTION OF SINGLE SWING, PIRS, OR DOULE EGRESS PIRS. ) URRIES MODEL 707. ) /4 (1) LTH OLT THROW IS REQUIRED. 4) YLINDRIL, MORTISE, OR FIRE EXIT HRDWRE IS EPTLE. 5) WELDED ONSTRUTION ONLY. 6) NY LISTED WELD IN OR SLIP-IN DRYWLL OR MSONRY NHOR MY E USED IN THIS FRME. 7) MY E PROVIDED S FOUR SIDED FRME, REFER TO SILL NHOR REQUIREMENTS, SILL MUST UTT ETWEEN VERTIL FRME MEMERS. VRIES PROFILE VRILE VRIES 16 G. (1.5) MIN. 1 G. (.6) MX. /8 (10) MIN. /4 (1) MX. 4-/4 (11) MIN. 10-1/ (67) MX. ) 1/4 (6) MIN. 1-/8 (5) MX. 1) 1) ) 16 G. (1.5) MIN. 1 G. (.6) MX. 4-/4 (11) MIN. 10-1/ (67) MX. HED ND JM SETION (51) MIN. (51) MIN. 4 (10) MX. (51) MX. HED 4 (10) MX. JM

26 Transom/Sidelite Frame ugust, MINUTE WITHOUT HOSE STREM MXIMUM RTING ELEVTION DETILS 11 7 (55) MX. GENERL NOTES: 1) /8 (10) MIN. GLSS POKET ) ) VRILE PROFILE 4) /8 (10) MIN. /4 (1) MX. 5) 4-1/ (14) MIN. 14 (56) MX. 1 (4018) MX. 4) 5/8 (16) MIN. ) SETION - 5/8 (16) ) ) MIN. 1) ) 5) ) 1 (5) MIN. 4 (10) MX. /8 (10) MIN. 1-/8 (5) MX. 5/8 (16) MIN. ) ) SETION - 1 (5) MIN. 1 (05) MX. 4) SETION - 1 (5) MIN. 1 (05) MX. ) 5) 5) /8 (10) MIN. 1-/8 (5) MX.

27 4 Transom/Sidelite Frame ugust, MINUTE WITHOUT HOSE STREM MXIMUM RTING. MXIMUM FRME SIZE: MXIMUM DOOR SIZE: MX. GLSS RE: **SEE NOTES 1& WLL ONSTRUTION: 1 (401) W X 11 7 (51) H SINGLE 4 0 (11) W X 10 0 H PIR 8 0 (48) W X 10 0 H 5/8 (16) H X 5/8 (16) W MIN. STOP; MX W OR H IS 10-/4 (788) NOT TO EXEED 568 SQ. IN. (870) OF VISILE GLSS MSONRY OR DRYWLL FRME ONSTRUTION: MTERIL: NHORS: FE OR ONTINUOUS WELDS. OLD ROLLED ND GLVNIZED STEEL 16 G. (1.5) MINIMUM TO 1 G. (.6) MXIMUM NY LISTED WELD IN OR SLIP-IN TYPE DRYWLL OR MSONRY NHORS MY E USED IN THIS FRME NOTE: 1) IF FIRE WINDOW FRME DOES NOT EXTEND TO THE FLOOR ND IS SUSPENDED OVER DRYWLL SILL, SUITLE NHOR MUST E USED IN THE SILL MEMER FOR EH 0 (76) OF LENGTH OR FRTION THEREOF. ) THE ONFIGURTION OF TRNSOM ND LIGHT RES MY VRY! ONLY LISTED GLZING MTERILS MY E USED IN THIS FRME. SEE FRME GLZING HRTS FOR DDITIONL GLZING OPTIONS.

28 5 Fire Window Frame ugust, MINUTE WITHOUT HOSE STREM MXIMUM RTING ELEVTION/SETIONS DETIL 7 (4) MX. 1 (4018) MX. GENERL NOTES: 1) /8 (10) MIN. GLSS POKET ) ) VRILE PROFILE 4) /8 (10) MIN. /4 (1) MX. 5) 4-1/ (14) MIN. 14 (56) MX. ) 4) 5/8 (16 MIN. SETION - ) 1 (5) MIN. 4 (10) MX. 5) /8 (10) MIN. 1-/8 (5) MX. ) 5/8 (16) MIN. ) ) 5/8 (16) MIN. 1) ) ) SETION - 1 (5) MIN. 1 (05) MX. 4) SETION - /8 (10) MIN. 1-/8 (5) MX. 5) 1 (5) MIN. 16 (406) MX. 5)

29 6 Fire Window Frame ugust, MINUTE WITHOUT HOSE STREM MXIMUM RTING. MXIMUM FRME SIZE: MXIMUM GLSS RES 1 (401) W X 7 (4) H 5/8 (16) H X 5/8 (16) W MIN. STOP; MX. W OR H IS 10-/4 (788); NOT TO EXEED 568 SQ. IN. (870) VISILE GLSS SEE FRME GLZING HRTS FOR DDITIONL GLZING OPTIONS. WLL ONSTRUTION: MSONRY OR DRYWLL FRME ONSTRUTION: MTERIL: NHORS: FE OR ONTINUOUS WELDS. OLD ROLLED ND GLVNIZED STEEL 16 G. (1.5) MINIMUM TO 1 G. (.6) MXIMUM NY LISTED WELD IN OR SLIP-IN TYPE DRYWLL OR MSONRY NHORS MY E USED IN THIS FRME NOTE: 1) IF THE FIRE WINDOW FRME DOES NOT EXTEND TO THE FLOOR ND IS SUSPENDED OVER DRYWLL SILL, SUITLE NHOR MUST E USED IN THE SILL MEMER FOR EH 0 (76) OF LENGTH OR FRTION THEREOF. ) THE ONFIGURTION OF GLSS LIGHT RES MY VRY. ONLY LISTED GLZING MTERILS MY E USED IN THIS FRME. ) THE UTHORITY HVING JURISDITION SHOULD REVIEW THE USE OF FIRE WINDOW FRME WITH 0 MINUTE - WITHOUT HOSE STREM RTING. 4) GLSS STOP SREW SPING #8 OVL HED SHEET METL SREW FROM EH END ND 1 (04.8) ON ENTER MX. 5) GLSS STOP EXTENDER MY E USED WITH THIS FRME.

30 7 Fire Window Frame (Masonry Walls Only) ugust, MINUTE MXIMUM RTING IN MSONRY WLLS ONLY ELEVTION/SETIONS DETIL 1 0 (658) MX. 5/8 (16) MIN. ) 1 6 (4115) MX. VRIES 5/8 (16) MIN. 1) ) VRIES SETION - 1 (5) MIN. 4 (10) MX. SETION - 1 (5) MIN. 4 (10) MX. ) 4) 5 (17) MIN. 14 (55.6) MX. VRIES GENERL NOTES: 1) /8 (10) MIN. GLSS POKET ) ) 5 (17) MIN. 14 (56) MX. 4) /8 (10) MIN. 1-/8 (5) MX. 5/8 (16) MIN. 1) SETION - ) ) VRIES 1 (5) MIN. 16 (406) MX. 4)

31 8 Fire Window Frame (Masonry Walls Only) ugust, MINUTE MXIMUM RTING MXIMUM FRME SIZE: GLZING REQUIREMENTS: WLL ONSTRUTION: 1 6 (4115) W X 1 0 (658) H SEE FRME GLZING HRTS FOR GLZING OPTIONS INLUDING MXIMUM HOURLY RTINGS. MXIMUM VISILE RE, MXIMUM HEIGHT ND WIDTH, MINIMUM STOP HEIGHT, ND GLSS POKET WIDTH FOR EH GLZING OPTION IS LISTED IN THE HRT. LISTED GLZING OMPOUND, 100% SILIONE, OR LOSED ELL FOM TPE MY E USED. SEE GLZING MNUFTURER S INSTLLTION INSTRUTIONS FOR GLSS OPTIONS. MSONRY OR DRYWLL FRME ONSTRUTION: MTERIL: NHORS: FE OR ONTINUOUS WELDS. OLD ROLLED ND GLVNIZED STEEL 16 G. (1.5) MINIMUM TO 1 G. (.6) MXIMUM NY LISTED WELD IN OR SLIP-IN TYPE DRYWLL OR MSONRY NHORS MY E USED IN THIS FRME NOTE: 1) GLSS STOP SREW SPING; NO. 8 OVL HED SHEET METL SREWS SPED (51) FROM EH END ND 1 (04.8) ON ENTER ) THE ONFIGURTION OF GLSS LIGHT RES MY VRY. ) THIS FRME MY E PROVIDED WITH SREW PPLIED FIELD SPLIE FOR ONNETION T THE JO SITE. 4) GLSS STOP EXTENDER MY E USED WITH THIS FRME. 5) SSEMLY HS NO TEMPERTURE RISE RTING.

32 Fire Window Frame ugust, MINUTE MXIMUM RTING DRYWLL WLLS ELEVTION/SETIONS DETIL 5 1 (1545) MX (048) MX. 5/8 (16) ) GENERL NOTES: MIN. 1) ) 1) /8 (10) MIN. GLSS POKET ) ) VRILE PROFILE 4) /8 (10) MIN. SETION - /4 (1) MX. 5) 4-1/ (114) MIN. 14 (56) MX. 4) /8 (10) MIN. 1-/8 (5) MX. 5) 1 (5) MIN. 4 (10) MX. ) 5/8 (16) MIN. 1) ) ) 5/8 (16) MIN. 1) ) ) SETION - 1 (5) MIN. 8 (0) MX. 4) SETION - /8 (10) MIN. 1-/8 (5) MX. 1 (51) MIN. 16 (406) MX. 5) 5)

33 0 Fire Window Frame October, MINUTE MXIMUM RTING OVERLL FRME SIZE: GLZING REQUIREMENTS: WLL ONSTRUTION: 10 0 (048) W X 5 1 (154) H; FOR USE IN DRYWLL WLLS. SEE FRME GLZING HRTS FOR GLZING OPTIONS INLUDING MXIMUM HOURLY RTINGS. MXIMUM VISILE RE, MXIMUM HEIGHT ND WIDTH, MINIMUM STOP HEIGHT, ND GLSS POKET WIDTH FOR EH GLZING OPTION IS LISTED IN THE HRT. LISTED GLZING OMPOUND, 100% SILIONE, OR LOSED ELL FOM TPE MY E USED. SEE GLZING MNUFTURER S INSTLLTION INSTRUTIONS FOR GLSS OPTIONS. DRYWLL FRME ONSTRUTION: MTERIL: NHORS: FE OR ONTINUOUS WELDS. OLD ROLLED ND GLVNIZED STEEL 16 G. (1.5) MINIMUM TO 1 G. (.6) MXIMUM NY LISTED WELD IN OR SLIP-IN TYPE DRYWLL NHOR NOTE: 1) IF FIRE WINDOW FRME IS INSTLLED OVER DRYWLL SILL, SUITLE NHOR MUST E USED IN THE SILL MEMER FOR EH 0 (76) OF SILL LENGTH. ) STOP HEIGHT EXTENDER MY E USED ON THESE FRMES. ) GLSS STOP SREW SPING: NO. 8 OVL HED SHEET METL SREWS SPED (51) FROM EH END ND 1 (04.8) ON ENTER. 4) THE ONFIGURTION OF GLSS LIGHT RES MY VRY. 5) SSEMLY HS NO TEMPERTURE RISE RTING.

34 1 Field Splice Frame pril, 00 FRMES WELDED T URRIES: PROVIDE FIELD SPLIES FOR FRMES THT EXEED SIZE SHOWN FIELD SPLIING RKETS ON WELDED FRMES WILL E PROVIDED. SEE NEXT PGE FOR SPLIE EXMPLES. FRMES WELDED T SERVIE ENTERS: FIELD SPLIING RKETS ON WELDED FRMES WILL E PROVIDED. SEE NEXT PGE FOR SPLIE EXMPLES.

35 Field Splice Frame pril, 00 FRMES WELDED T URRIES: 16 0 FIELD SPLIE HJ SJ FIELD SPLIE SLEEVES, WILL E PPLIED TO STRIKE JM, ONE FOR EH TTHING HORIZONTL RIL FIELD SPLIE 15 0 FIELD SPLIE SLEEVES, WILL E PPLIED TO HORIZONTL MULLION, ONE FOR EH TTHING VERTIL RIL.

36 Fire Window Frame ow Window March, 016 SSEMLY NO. W--01 FIRE RTINGS - 60 MINUTE MEETS THE RITERI OF STNDRD UL (000) ND U STNDRD 7-4, (17) U.L. RTED ONLY 1 8 (861) MX. (DRYWLL) 1 6 (4115) MX. (MSONRY) 1 8 (861) MX. (DRYWLL) 1 6 (4115) MX. (MSONRY) (454) MX. (DRYWLL) 1 (658) MX. (MSONRY) 1 8 (861) MX. (DRYWLL) 1 6 (4115) MX. (MSONRY) 1 8 (861) MX. (DRYWLL) 1 6 (4115) MX. (MSONRY) 1 8 (861) MX. (DRYWLL) 1 6 (4115) MX. (MSONRY) 1-1/4 (1.7) MIN. 4 (10) MX., 1-1/4 (1.7) MIN. 1 (05) MX. 0 ORNER NGLED ORNER

37 4 Fire Window Frame ow Window May, 015, ROSS SETION 1. FIRE WINDOW FRME + THE FRME IS TO E INSTLLED IN ORDNE WITH THE REOMMENDED INSTLLTION PRTIES PRESENTED IN NFP 80, FIRE-RTED HOLLOW METL DOORS ND WINDOWS, ND NMM STNDRD , FIRE-RTED HOLLOW METL DOORS ND FRMES. THE WINDOW FRME MY INLUDE DOOR FRME THT IS PRT OF FIRE RTED DOOR SSEMLY HVING MIN. 60 MINUTE RTING. THE SI FRME ONSTRUTION ND LIMITTIONS RE S FOLLOWS: ) OPENING SIZE-MXIMUM WLL OPENING SIZE SHLL E 15 IN. FOR GYPSUM WLLORD ONSTRUTION ND 16 IN. FOR MSONRY ONSTRUTION. FRME PROJETION FROM FE OF WLL SHLL NOT EXEED THE MX. LLOWLE OPENING WIDTH. ) MULLION ND JM FE DIMENSIONS 1-1/4 MIN. 4 IN. MX. SILL FE DIMENSION 1-1/4 IN. MIN. - 1 IN. MX. ) THE FRME IS TO E PROVIDED WITH NHORS SUITLE FOR THE WLL ONDITIONS IN ORDNE WITH NMM STNDRD D) THE INSIDE NGLE ETWEEN FRME SEGMENTS MY VRY. INSIDE NGLES OF 0 ND 15 RE SHOWN IN THE ILL. FRME URVTURE TO E ONTINUOUS OR SEGMENTED. E) SPLIES - THE FRME MY E PROVIDED WITH SPLIES FOR SHIPMENT PURPOSES.

38 5 Fire Window Frame ow Window pril, 00 ) GLZING MTERILS* 1/4 IN. THIK WIRED GLSS. SEE GLZING MTERILS TEGORY (KMZ) FOR NMES OF LSSIFIED OMPNIES ND THE MXIMUM SIZE OF GLZING MTERIL. GLZING MTERIL SHLL HVE MINIMUM RTING OF /4 HR. ) GLZING MTERILS (LTERNTE)* S N LTERNTE TO WIRED GLSS, THE FOLLOWING GLZING MTERILS MY E USED. SEE GLZING MTERILS (KMZ) FOR THE MXIMUM SIZE OF GLZING MTERIL. GLZING MTERIL SHLL HVE MINIMUM RTING OF /4 HR. NIPPON ELETRI GLSS O LTD - NON-WIRED /16 IN. FIRELITE, FIRELITE NT, 5/16 IN. THIK FIRELITE PLUS, FIRELITE IGU MESTEK O. NEMOSTT PRODUTS - NON-WIRED /16 IN. FIRELITE, FIRELITE NT, 5/16 IN. THIK FIRELITE PLUS, FIRELITE IGU TEHNIL GLSS PRODUTS - NON WIRED /16 IN. FIRELITE, FIRELITE NT, 5/16 IN. THIK FIRELITE PLUS, FIRELITE IGU ) GLZING OMPOUND* GLZING OMPOUND SHLL OMPLETELY FILL THE GLZING POKET WITH MIN. THIKNESS OF 1/16 IN. ETWEEN THE GLZING ND THE FRME. SEE GLZING MTERILS TEGORY (KMZ) FOR NMES OF GLZING OMPOUNDS TO E USED WITH GLZING MTERILS (ITEM ). 4) WLL ONSTRUTION MSONRY OR DRYWLL ONSTRUTION (STEEL STUD GYPSUM WLLORD WLL SHOWN). ) GYPSUM WLLORD THE ONE HOUR MINIMUM FIRE-RTED GYPSUM WLLORD/STUD WLL SSEMLY SHLL E ONSTRUTED OF THE MTERILS ND IN THE MNNER SPEIFIED IN THE INDIVIDUL U00 OR U400 SERIES WLL ND PRTITION DESIGNS IN THE UL FIRE RESISTNE DIRETORY. THE FIRE WINDOW FRME IS NHORED TO THE STEEL STUDS OR WOOD STUDS USING THE PPROPRITE NHORS SHIPPED WITH THE FRME. WHERE FRME IS DJENT TO GYPSUM WLL ORD SSEMLY, THE OPENING IS TO E FRMED WITH DOULE STUDS. GYPSUM WLLORD TO E INSERTED INTO THE FRME THROT 1/ IN. MINIMUM. ) MSONRY FRME TO E INSTLLED INTO MSONRY ONSTRUTION (RIK ONRETE LOK) WITH ONE-HOUR MINIMUM FIRE RTING USING MSONRY TYPE NHORS. +ERING THE UL LISTING MRK. *ERING THE UL LSSIFITION MRK.

39 6 Fire Window Frame (Drywall Walls with Non ombustible Sill) ugust, MINUTE MXIMUM RTING DRYWLL WLLS WITH NONOMUSTILE SILL ELEVTION/SETIONS DETIL 10 0 (048) MX (454) MX. 5/8 (16) ) GENERL NOTES: MIN. 1) /8 (10) MIN. GLSS POKET ) ) VRILE PROFILE 4) /8 (10) MIN. SETION - /4 (1) MX. 5) 4-1/ (114) MIN. 14 (56) MX. 4) /8 (10) MIN. 1-/8 (5) MX. 5) ) 1 (5) MIN. 4 (10) MX. ) 5/8 (16) MIN. 1) ) ) 5/8 (16) MIN. 1) ) ) SETION - 1 (5) MIN. 8 (0) MX. 4) SETION - /8 (10) MIN. 1-/8 (5) MX. 1 (51) MIN. 16 (406) MX. 5) 5)

40 7 Fire Window Frame (Drywall Walls with Non ombustible Sill) ugust, MINUTE MXIMUM RTING OVERLL FRME SIZE: GLZING REQUIREMENTS: 11 4 (454) W X 10 0 (048) H; FOR USE IN DRYWLL WLLS WITH NON-OMUSTILE MSONRY OR ONRETE SILL. SEE FRME GLZING HRTS FOR GLZING OPTIONS INLUDING MXIMUM HOURLY RTINGS. MXIMUM VISILE RE, MXIMUM HEIGHT ND WIDTH, MINIMUM STOP HEIGHT, ND GLSS POKET WIDTH FOR EH GLZING OPTION IS LISTED IN THE HRT. LISTED GLZING OMPOUND, 100% SILIONE, OR LOSED ELL FOM TPE MY E USED. SEE GLZING MNUFTURER S INSTLLTION INSTRUTIONS FOR OPTIONS. WLL ONSTRUTION: DRYWLL WITH NON-OMUSTILE SILL FRME ONSTRUTION: MTERIL: NHORS: FE OR ONTINUOUS WELDS. OLD ROLLED ND GLVNIZED STEEL 16 G. (1.5) MINIMUM TO 1 G. (.6) MXIMUM NY LISTED WELD IN OR SLIP-IN TYPE DRYWLL OR MSONRY NHORS MY E USED IN THIS FRME NOTE: 1) GLSS STOP SREW SPING; NO. 8 OVL HED SHEET METL SREWS SPED (51) FROM EH END ND 1 (04.8) ON ENTER ) THE ONFIGURTION OF GLSS LIGHT RES MY VRY. ) THIS FRME MY E PROVIDED WITH SREW PPLIED FIELD SPLIE FOR ONNETION T THE JO SITE. 4) GLSS STOP EXTENDERS MY E USED WITH THIS FRME. 5) SSEMLY HS NO TEMPERTURE RISE RTING.

41 8 Transom/Sidelite Frame ugust, MINUTE MXIMUM RTING IN DRYWLL WLLS ELEVTION DETILS / (54) MX. 1 0 (658) MX. GENERL NOTES: VRILE PROFILE 4-/4 (11) MIN. 14 (56) MX. /8 (10) MIN. 1-/8 (5) MX. /8 (10) MIN. /8 (10) MIN. SETION - JM/HED /8 (10) MIN. (51) MIN. 4 (10) MX. SETION - MULLION (51) MIN. 6 (15) MX. SETION - SILL (51) MIN. 16 (406) MX. 4-/4 (11) MIN. 10-1/ (67) MX. /8 (10) MIN.

42 Transom/Sidelite Frame ugust, MINUTE MXIMUM RTING MXIMUM FRME SIZE: 1 0 (658) W X / (54) H. MXIMUM DOOR SIZE: MX. GLSS RE: WLL ONSTRUTION: FRME ONSTRUTION: MTERIL: NHORS: SINGLE 4 0 (11) X 10 0 (048) PIR 8 0 (48) X 10 0 (048) FOR LISTED 1/4 WIRED GLSS 5/8 (16) H X 5/8 (16) W MINIMUM STOP; MXIMUM W OR H SHLL E 54 (17) NOT TO EXEED 16 (8617) SQURE INHES OF VISILE GLSS. MUST USE LISTED GLZING OMPOUND OR 100% SILION. FOR PEMKO FG000 WITH 1/4 WIRED PILKINGTON GLSS: 5/8 (16) H 5/8 (16) W MINIMUM STOP; MXIMUM W OR H SHLL E 106 (6) NOT TO EXEED 4704 SQ. IN. SEE FRME GLZING HRTS FOR DDITIONL GLZING OPTIONS. DRYWLL ONLY FE OR ONTINUOUS WELDS. OLD ROLLED ND GLVNIZED STEEL 16 G. (1.5) MINIMUM TO 1 G. (.6) MXIMUM NY LISTED WELD IN OR SLIP-IN TYPE DRYWLL OR MSONRY NHORS MY E USED IN THIS FRME NOTE: 1) THE ONFIGURTION OF THE TRNSOM ND SIDE RES MY VRY. ) THIS FRME MY E PROVIDED WITH SREW PPLIED FIELD SPLIE FOR ONNETION T THE JO SITE. ) GLSS STOP SREW SPING IS (51) FROM EH END ND 1 (04.8) ON ENTER.

43 40 Transom/Sidelite Frame ugust, MINUTE MXIMUM RTING IN MSONRY WLLS ELEVTION DETILS 1 0 (658) MX. 1 6 (4115) MX. GENERL NOTES: VRILE PROFILE 4-/4 (11) MIN. 14 (56) MX. /8 (10) MIN. SETION - JM/HED 1 (5) MIN. 4 (10) MX. /8 (10) MIN. /8 (10) MIN. /8 (10) MIN. 1-/8 (5) MX. SETION - MULLION 1 (5) MIN. 1 (15) MX. SETION - SILL 1 (51) MIN. 16 (406) MX. 5/8 (16) MIN. /8 (10) MIN. 1-/8 (5) MX.

44 41 Transom/Sidelite Frame ugust, MINUTE MXIMUM RTING MXIMUM FRME SIZE: MXIMUM DOOR SIZE: MX. GLSS RE: WLL ONSTRUTION: FRME ONSTRUTION: MTERIL: NHORS: 1 6 (4115) W X 1 0 (658) H SINGLE 4 0 (11) X 10 0 (048) PIR 8 0 (48) X 10 0 (048) FOR LISTED 1/4 WIRED GLSS 5/8 (16) H X 5/8 (16) W MINIMUM STOP; MXIMUM W OR H SHLL E 54 (17) NOT TO EXEED 16 (8617) SQURE INHES OF VISILE GLSS. MUST USE LISTED GLZING OMPOUND OR 100% SILION. FOR PEMKO FG000 WITH 1/4 WIRED PILKINGTON GLSS: 5/8 (16) H 5/8 (16) W MINIMUM STOP; MXIMUM W OR H SHLL E 106 (6) NOT TO EXEED 4704 SQ. IN. SEE FRME GLZING HRTS FOR DDITIONL GLZING OPTIONS. MSONRY ONLY FE OR ONTINUOUS WELDS. OLD ROLLED ND GLVNIZED STEEL 16 G. (1.5) MINIMUM TO 1 G. (.6) MXIMUM NY LISTED WELD IN OR SLIP-IN TYPE DRYWLL OR MSONRY NHORS MY E USED IN THIS FRME NOTE: 1) THE ONFIGURTION OF THE TRNSOM ND SIDE RES MY VRY. ) THIS FRME MY E PROVIDED WITH SREW PPLIED FIELD SPLIE FOR ONNETION T THE JO SITE. ) GLSS STOP SREW SPING IS (51) FROM EH END ND 1 (04.8) ON ENTER.

45 4 Fire Window Frame ugust, MINUTE MXIMUM RTING ELEVTION/SETION DETILS MSONRY ELEVTION 10 1 (07) MX. DRYWLL ELEVTION / (1511) MX. 10 (0) MX. -1/ (807) MX. GENERL NOTES: /8 (10) MIN. GLSS POKET VRILE PROFILE /8 (10) MIN. /4 (1) MX. ƒ 4-7/8 (14) MIN. 14 (56) MX. SETION - JM/HED 1 (5) MIN. 4 (10) MX. ƒ /8 (10) MIN. 1-/8 (5) MX. SETION - MULLION 1 (5) MIN. 1 (05) MX. SETION - SILL /8 (10) MIN. 1-/8 (5) MX. ƒ 1 (5) MIN. 16 (406) MX. ƒ

46 4 Fire Window Frame ugust, MINUTE MXIMUM RTING OVERLL FRME SIZE: ) 10 (0) W X 10 1 (07) H; FOR USE IN EITHER MSONRY WLLS OR DRYWLL WLLS WITH NON-OMUSTILE SILL. ) -1/ (807) W X / (1511) H; FOR USE IN EITHER MSONRY WLLS OR DRYWLL WLLS WITH DRYWLL SILL. MX. GLSS RE: WLL ONSTRUTION: FRME ONSTRUTION: MTERIL: NHORS: 5/8 (16) H X 5/8 (16) W GLSS STOP; MX. WIDTH: 54 (17); MX. HEIGHT: 77-/4 (175) 71 SQ. INHES ( ) OF VISILE GLSS. - GLZING MTERIL: /16 (5) THIK FIRELITE OR 5/16 (8) THIK FIRELITE PLUS GLSS ONLY! - GLZING OMPOUNDS: 100% SILION, DP, OR METULK 0. DRYWLL OR MSONRY WELDED JOINTS ONLY! OLD ROLLED ND GLVNIZED STEEL 16 G. (1.5) MINIMUM TO 14 G. (1.) MXIMUM NY LISTED WELD IN OR SLIP-IN TYPE DRYWLL OR MSONRY NHORS MY E USED IN THIS FRME NOTE: 1) IF FIRE WINDOW FRME IS INSTLLED OVER DRYWLL SILL, SUITLE NHOR MUST E USED IN THE SILL MEMER FOR EH 0 (76) OF SILL LENGTH OR FRTION THEREOF. ) GLSS STOP SREW SPING: NO. 8 SHEET METL SREWS SPED (51) FROM EH END ND 1 (04.8) ON ENTER.

47 44 Transom/Sidelite Frame ugust, MINUTE MXIMUM RTING ELEVTION DETILS 10 1 (07) MX. 10 (0) MX. GENERL NOTES: /8 (10) MIN. GLSS POKET VRILE PROFILE /8 (10) MIN. /4 (1) MX. ƒ 4-7/8 (14) MIN. 14 (56) MX. 5/8 (16) MIN. SETION - ƒ 1 (5) MIN. 4 (10) MX. /8 (10) MIN. 1-/8 (5) MX. SETION - 1 (5) MIN. 1 (05) MX. SETION - /8 (10) MIN. 1-/8 (5) MX. 1 (5) MIN. 16 (406) MX. ƒ ƒ

48 45 Transom/Sidelite Frame ugust, MINUTE MXIMUM RTING MXIMUM FRME SIZE: MXIMUM DOOR SIZE: MX. GLSS RE: **SEE NOTES 1 & WLL ONSTRUTION: FRME ONSTRUTION: MTERIL: NHORS: 10 (0) W X 10 1 (07) H SINGLE 4 0 (11) W X 10 0 (048) H PIR 8 0 (48) W X 10 0 (048) H 5/8 (16) H X 5/8 (16) W GLSS STOP; MX. WIDTH: 54 (17); MX. HEIGHT: 77-/4 (175) 71 SQ. INHES ( ) OF VISILE GLSS. DRYWLL OR MSONRY FE OR ONTINUOUS WELDS. OLD ROLLED ND GLVNIZED STEEL 16 G. (1.5) MINIMUM TO 1 G. (.6) MXIMUM NY LISTED WELD IN OR SLIP-IN TYPE DRYWLL OR MSONRY NHORS MY E USED IN THIS FRME NOTE: 1) GLZING MTERIL SHLL E FIRELITE GLSS ONLY. ) GLZING OMPOUNDS RE EITHER 100% SILION, DP,, OR METULK 0. ) IF SIDELIGHT IS INSTLLED OVER DRYWLL SILL, SUITLE NHOR MUST E USED IN THE SILL MEMER FOR EH 0 INHES (76) OF SILL LENGTH OR FRTION THEREOF. 4) GLSS STOP SREW SPING: NO. 8 SHEET METL SREWS SPED (51) FROM EH END ND 1 (04.8) ON ENTER.

49 46 Transom/Sidelite Frame (Masonry Walls Only) ugust, MINUTE MXIMUM RTING IN MSONRY WLL ELEVTION/SETION DETILS 1 0 (658) 1 6 (411) MX. GENERL NOTES: VRILE PROFILE 4-/4 (11) MIN. 14 (56) MX. /8 (10) MIN. SETION - JM/HED (50) MIN. 4 (10) MX. /8 (10) MIN. 1-/8 (5) MX. /8 (10) MIN. /8 (10) MIN. SETION - MULLION (50) MIN. 1 (05) MX. SETION - SILL (50) MIN. 16 (406) MX. /8 (10) MIN. 1-/8 (5) MX.