REM 2500 GRAIN VAC PARTS CATALOGUE

Transcription

1 REM 500 GRAIN VAC PARTS CATALOGUE

2 INTRODUCTION This parts manual is set up to show all the service parts for Rem 500 Grain Vac. The information required when order parts is as follows: - part number - description - number of pieces required In producing this parts catalogue every effort has been made to ensure accuracy. If you discover an error, please inform us. Phone: In Canada: Rem Enterprises Inc. Box 107 Swift Current, SK S9H 3X4 Ph: (306) , Fax: (306) remsales@rem.sk.ca US Shipping Office located in Shenandoah, IA

3 REM 500 GRAIN VAC PARTS AUG 15/07 TABLE OF CONTENTS PRODUCT ILLUSTRATIONS PAGE PTO SHAFT A DRIVE SHAFT AND CLUTCH ASSEMBLY A GEARBOX AND BREATHER EXTENSION KIT A WHEEL AND AXLE ASSEMBLY A FRAME ASSEMBLY - SPRING ASSIST A FRAME ASSEMBLY - SPRING ASSIST A TELESCOPING AXLE - FRAME ASSEMBLY (HYD) A TELESCOPING AXLE - FRAME ASSEMBLY (HYD) A TORFLEX FRAME - HYDRAULIC A TORFLEX AXLE ,6-3A HOSE RACK ASSEMBLY A BODY - INLET SIDE A BODY - AUGER SIDE A EXHAUST ASSEMBLY A ROUND EXHAUST ASSEMBLY A ROUND EXTENSION EXHAUST A AUGER DRIVE - PTO SECTION A AUGER DRIVE - GEARBOX SECTION A AUGER DRIVE - AUGER SECTION A REAR PULLEY DRIVE A FAN DRIVE A DRUM ASSEMBLY A INLET ASSEMBLY A LOWER AUGER SECTION ASSEMBLY - SPRING ASSIST A MIDDLE AUGER SECTION ASSEMBLY - SPRING ASSIST A UPPER AUGER SECTION ASSEMBLY - SPRING ASSIST A UPPER AUGER SECTION ASSEMBLY - SPRING ASSIST A LOWER AND MIDDLE AUGER SECTION ASSEMBLY - HYDRAULIC A UPPER AUGER SECTION ASSEMBLY - HYDRAULIC A HYDRAULIC HOSE AND CYLINDER ASSEMBLY A STANDARD HOSE A FLOOR SWEEP ASSEMBLY A TELESCOPING TUBE OPTIONS A TRANSITION OPTIONS A 6" HOSE OPTIONS A 7" HOSE OPTIONS A BASKETWEAVE AND NONBASKETWEAVE OPTIONS A DRILL CLEAN OUT - 4" HOSE OPTIONS A 7" CHAMFERED CLEAN UP NOZZLE OPTION A 8" HOSE OPTION A EXHAUST AERATION AND CONVERSION KIT OPTIONS A FOUR HOSE EXTENSION KIT OPTION A HIRED HAND KIT OPTION A DUST COLLECTOR OPTION A FINE DRUM SCREEN OPTION A BRUSH KIT A LIGHT KIT OPTION A SPOUT OPTION A STUB UNLOADING AUGER KIT OPTION A HYDRAULIC AUGER ANGLE INCLINER OPTION A DUMPER EXTENSION CHUTE OPTION A DECALS A

4

5 PTO SHAFT PAGE 1A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # PTO SHAFT,W400 SEIRES,# WALTERSCHEID MALE HALF SHAFT C/W SHIELDING (INCLUDES 4,5,7-10,13-15,17,19) FEMALE HALF SHAFT C/W SHIELDING (INCLUDES 6,7,9,11,1,14-16,18,0,1) YOKE # /8 1 SPL A.S. C/W # A.S. COLLAR KIT # COMPLETE CLUTCH ASSEMBLY # (SEE PAGE.) CROSS & BEARING KIT # INBOARD YOKE 1B # SPRING PIN # X INNER PROFILE # OUTER PROFILE #09147 A INBOARD YOKE #19519 A SHIELD CONE 6 RIB # SCREW # BEARING RING # SAFTEY CHAIN # OUT. SHIELD TUBE OVAL # INNER SHIELD TUBE ROUND # DANGER DECAL - SHIELD # DANGER DECAL - STEEL # SHIELD CONE 6 RIB # GREASE ZERK-M8X1-67.5DEG GREASEZERK-M8X1-PKG OF 3 OF

6

7 500 DRIVE SHAFT AND CLUTCH ASSEMBLY PAGE A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # H Nut M8 DIN 6330 # BELLEVILLE SPRING $ WHITE DOT BELLEVILLE SPRING # RED DOT THRUST PLATE # FRICTION DISK # DRIVE PLATE # DRIVE PLATE # HUB 1 3/8" - 5/16" KEYWAY # CLUTCH HOUSING # COMPLETE CLUTCH ASSEMBLY # QUICK DISCONNECT FLG KIT (1-18) # BACK UP RING # COMPRESSION SPRING # BALL LOCK COLLAR # FLANGED RING # SNAP RING # SNAP RING #

8 500 - PAGE 3 GEAR BOX AUGER DRIVE PTO END

9 GEARBOX 500- PAGE 3A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # SHAFT-GEAR SHAFT-PINION GEAR-STRAIGHT BEVEL BEARING-TAPERED ROLLER BEARING-TAPERED ROLLER SEAL, RADIAL SHAFT PLUG, HEX SOCKET M16 X SEAL, COPPER 16 X BREATHER, GEARBOX VENT GEARBOX-GKN GRAINVAC 1:1 1

10 500 - PAGE 4 WHEEL AND AXLE ASSEMBLY

11 500 WHEEL AND AXLE ASSEMBLY 500- PAGE 4A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # BOLT WHEEL ASSEMBLY TIRE-ST05/75R15 (BSL) VALVE STEM TR WHEEL-RIM 15" X 5" X 5 BOLT GV SPINDLE & HUB COMP. (INCL. 6-17) GREASE ZERK - 1/4-DRV STR BEARING - LM DC 1 HUB CAP F0305 NUT-CASTLE 3/4" UNF GR OUTER RACE F904 BOLT - WHEEL 1/ X 1 3/4" UNF (WE10) SPINDLE - AXLE - S413-Q PINS-COTTER 3/16 X 1 1/ GREASE SEAL - SE BEARING - LM INNER RACE HUB H BOLT # 1

12 500 - PAGE 5 SPRING ASSIST AXLE AND FRAME ASSEMBLY SERIAL BREAK NOTE: TORQUE BOLTS TO: FT-LBS ( IN-LBS)

13 SPRING ASSIST AXLE AND FRAME ASSEMBLY 500- PAGE 5A SERIAL BREAK NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # MAIN FRAME WELDMENT - S/A FENDER WELDMENT BASE HITCH PPI-16VR SOLID AXLE TUBE WELD JACK - TOP SCREW - CROWN BOLT WHEEL ASSEMBLY GV SPINDLE & HUB COMPLETE CLEVIS PPI-107VR SAFTEY CHAIN 10,000LB BODY COMPLETE WELDMENT C050 NUT NY-LOCK 7/16 UNC GR WASHER-FLAT 7/16 DIA. USS C3344 BOLT-HEX 5/8 X 4 1/ UNC GR C990 BOLT-HEX 1/ X 7 UNC GR C0510 BOLT-WHIZ 1/ X 1 UNC GR C960 BOLT-HEX 1/ X 4 1/ UNC GR C080 NUT-LOCK FLG UNI-TRQ 5/8 UNC GR C0500 NUT-LOCK FLG UNI-TRQ 1/ UNC GR C770 BOLT-HEX 7/16 X 7 UNC GR C766 BOLT-HEX 7/16 X 6 UNC GR C0515 BOLT-WHIZ 1/ X 1 1/ UNC GR.5 4

14 500 - PAGE FRAME ASSY S/A SERIAL BREAK A

15 500 FRAME ASSEMBLY S/A 500- PAGE 5-1A SERIAL BREAK NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # TORFLEX FRAME WELD AXLE ASSY TORFLEX 3500# A AXLE ASSY TORFLEX 3500# HIGH-PROFILE JACK - TOP SCREW - CROWN FENDER BODY COMPLETE WELDMENT CLEVIS PPI-107VR F-0500 WHEEL NUT 1/ UNF PLTD F388 BOLT-HEX 5/8 X 1 1/ UNF GR F080 NUT-LOCK UNI-TRQ 5/8 UNF WASHER 5/8 ID X 1 5/16 OD BASE HITCH PPI-16VR TIRE ASSEMBLY C0515 BOLT-WHIZ 1/ X 1 1/ UNC GR C0500 NUT-LOCK UNI-TRQ 1/ UNC GR C50 BOLT-WHIZ 3/8 X 1 UNC GR C035 NUT-LOCK FLG UNI-TRQ 3/8 UNC GR C3344 BOLT-HEX 5/8 X 4 1/ UNC GR C960 BOLT-HEX 1/ X 4 1/ UNC GR C080 NUT-LOCK UNI-TRQ 5/8 UNC GR SAFETY CHAIN 10,000 LB. 1

16 500 - PAGE 6 TELESCOPING AXLE FRAME ASSEMBLY (HYDRAULIC) SERIAL BREAK

17 TELESCOPING AXLE FRAME ASSEMBLY (HYDRAULIC) 500- PAGE 6A SERIAL BREAK NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # AXLE TUBE WELDMENT TELESCOPING TUBE WELDMENT C050 NUT NY-LOCK 7/16 UNC GR C0510 BOLT-WHIZ 1/ X 1 UNC GR FENDER WELDMENT BOLT WHEEL ASSEMBLY C080 NUT-LOCK UNI-TRQ 5/8 UNC GR C960 BOLT-HEX 1/ X 4 1/ UNC GR C0500 NUT-LOCK FLG UNI-TRQ 1/ UNC GR C770 BOLT-HEX 7/16 X 7 UNC GR JACK - TOP SCREW - CROWN GV SPINDLE & HUB COMPLETE C888 BOLT-HEX 1/ X 1 UNC GR C0515 BOLT-WHIZ 1/ X 1 1/ UNC GR C990 BOLT-HEX 1/ X 7 UNC GR C766 BOLT-HEX 7/16 X 6 UNC GR C3344 BOLT-HEX 5/8 X 4 1/ UNC GR MAIN FRAME WELDMENT - HYD BASE HITCH PPI-16VR TELESCOPING CLAMP CLEVIS PPI-107VR WASHER-FLAT 7/16 DIA. USS 4

18 PAGE 6-1 REV. APR 4/07 AXLE FRAME ASSEMBLY (HYDRAULIC) SERIAL BREAK

19 AXLE FRAME ASSEMBLY (HYDRAULIC) 500- PAGE 6-1A SERIAL BREAK REV. APR 4/07 NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # SOLID AXLE C050 NUT NY-LOCK 7/16 UNC GR C0510 BOLT-WHIZ 1/ X 1 UNC GR FENDER WELDMENT BOLT WHEEL ASSEMBLY C080 NUT-LOCK UNI-TRQ 5/8 UNC GR C960 BOLT-HEX 1/ X 4 1/ UNC GR C0500 NUT-LOCK FLG UNI-TRQ 1/ UNC GR C770 BOLT-HEX 7/16 X 7 UNC GR JACK - TOP SCREW - CROWN GV SPINDLE & HUB COMPLETE C990 BOLT-HEX 1/ X 7 UNC GR C766 BOLT-HEX 7/16 X 6 UNC GR C3344 BOLT-HEX 5/8 X 4 1/ UNC GR MAIN FRAME WELDMENT - HYD BASE HITCH PPI-16VR CLEVIS PPI-107VR WASHER-FLAT 7/16 DIA. USS 4

20 500 - PAGE 6- REV. MAY 14/ TORFLEX FRAME HYD SERIAL BREAK A

21 500 TORFLEX FRAME HYD 500- PAGE 6-A SERIAL BREAK 930+ REV. MAY 14/07 NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # TORFLEX FRAME WELD AXLE ASSY TORFLEX 3500# A AXLE ASSY TORFLEX 3500# HIGH-PROFILE JACK - TOP SCREW - CROWN FENDER BODY COMPLETE WELDMENT CLEVIS PPI-107VR F388 BOLT-HEX 5/8 X 1 1/ UNF GR F0500 NUT-LOCK UNI-TRQ 5/8 UNF F-0500 WHEEL NUT 1/ UNF PLTD WASHER 5/8 ID X 1 5/16 OD BASE HITCH PPI-16VR TIRE ASSEMBLY C0515 BOLT-WHIZ 1/ X 1 1/ UNC GR C0500 NUT-LOCK UNI-TRQ 1/ UNC GR C50 BOLT-WHIZ 3/8 X 1 UNC GR C035 NUT-LOCK FLG UNI-TRQ 3/8 UNC GR C3344 BOLT-HEX 5/8 X 4 1/ UNC GR C960 BOLT-HEX 1/ X 4 1/ UNC GR C080 NUT-LOCK UNI-TRQ 5/8 UNC SAFETY CHAIN 10,000 LB HOSE HOLDER GRAIN VAC 1

22 500 - PAGE 6-3 TORFLEX AXLE

23 500 TORFLEX AXLE 500- PAGE 6-3A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # AXLE ASSY TORFLEX 3500# HIGH-PROFILE HUB ( NAT'L REF #84545 ) DRIVE-IN STUD ( NAT'L REF #7-1 ) SEAL ( NAT'L REF #58846 ) INNER RACE ( NAT'L REF #L68111 ) INNER BEARING ( NAT'L REF #L68149 ) OUTER BEARING ( NAT'L REF # L44649 ) OUTER RACE ( NAT'L REF #L44610 ) NUT ( NAT'L REF #X103R ) GREASE CAP ( NAT'L REF #46749 )

24 500 - PAGE 7 HOSE RACK ASSEMBLY REV. SEPT 5/

25 HOSE RACK ASSEMBLY 500- PAGE 7A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # FRAME ASSEMBLY C0500 NUT-LOCK FLG UNI-TRQ 1/ UNC GR /" MOTORCYCLE TIE-DOWN PLASTIC PLUG 1 1/" SQUARE TIE-DOWN RUBBER MIDDLE UPRIGHT TUBE WELD PLASTIC PLUG 1 " SQUARE MIDDLE UPRIGHT TUBE ASSEMBLY (INCL. 4-7,14,15) END UPRIGHT TUBE WELD END UPRIGHT TUBE ASSEMBLY (INCL. 4,5,7,9,14,15) TUBE RACK WELDMENT HOSE RACK PANEL ASSEMBLY (INCL. 4,5,8,11,15) C051 BOLT-WHIZ 1/ X 1 1/4 UNC GR WAHER-FLAT 5/16 DIA. USS C00 NUT NY-LOCK 5/16 UNC GR.5 3

26 500 - PAGE 8 BODY - INLET SIDE REV. JULY 11/ A DETAIL A SCALE 1 : 10

27 500 BODY - INLET SIDE 500- PAGE 8A REV. JAN 0/09 NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # BODY COMPLETE WELDMENT SEAL - CUT RING TELESCOPE TUBE ASSEMBLY PLUG INLET ASSEMBLY FRONT BODY GUARD TENSION LATCH CLAMP C140 BOLT-WHIZ 1/4 X 1/ UNC GR C000 NUT-WHIZ FLG 1/4 UNC GR PTO HOLDER C54 BOLT-WHIZ 3/8 X 1/ UNC GR C035 NUT NY-LOCK 3/8 UNC GR BENT PIN PIN - HITCH CLIP CP-86H WRAP - BOLT IN C3790 BLT-RND SKT HD 3/8 X C035 NUT-LOCK UNI-TRQ 3/8 UNC C501 BLT-CARR 3/8 X1 GR C035 NUT-WHIZ FLG 3/8 UNC GR RELIEF DOOR WELDMENT RELIEF SLIDE COVER C05 NUT-LOCK UNI-TRQ 1/4 UNC GR C35 BLT-CARR 1/4 X 3/4 UNC GR INSPECTION DOOR RUBBER /4 X 1 1/ WEATHERSTRIPPING 10.3' GLASS WINDOW 4 7/8 DIA 1/4 THICK INSPECTION DOOR ASSEMBLY (INCL 19-5) ST-6009 BOLT-TEK #10-16 X 1/ CLAMP UNIVERSAL C550 BLT-SKT HEAD 1/4 X 1/ STNLS. STL HOSE CLAMP ADJUSTMENT C00 NUT NY-LOCK 5/16 UNC GR C50 NUT-FLG UNI-TRQ 1/4 UNC GR CLEVIS-PIN 1/4 X 1 17/3 SN #B HITCH PIN - SN #B

28 500 - PAGE 9 REV. JUN 18/07 BODY - AUGER SIDE 8A DETAIL A SCALE 1 : REAR 6 NOTE: REFER TO LOWER AUGER SECTION ASSEMBLY PAGE (PG 18) FOR HARDWARE TO ATTACH PART #6. FRONT

29 500 BODY - AUGER SIDE 500- PAGE 9A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # C00 NUT-WHIZ FLG 5/16 UNC GR BODY COMPLETE WELDMENT CLEANOUT ASSEMBLY SIDE GRAIN DEFLECTOR - REAR SIDE GRAIN DEFLECTOR - FRONT HANDLE KEEPER CLEANOUT WELD TRANSPORT BRACKET - HYD 1 8A TRANSPORT BRACKET - S/A WELDMENT - AUGER RELEASE BACK WELDMENT - AUGER RELEASE FRONT PIN-LATCH PIN-ROLL 1/8 X WASHER-FLAT 5/8 DIA. SAE AUGER LATCH SPRING GV PINS-COTTER 3/3 X 1/ WASHER-FLAT 1/4 DIA USS STRIP-SLIDE RIVET-MONOBOLT CLEVIS 1/4 X 1 17/3 - SN #B DEFLECTOR - BACK BOLT-TEK #10-16 X WASHER-FLAT 5/16 DIA USS C00 NUT NY-LOCK 5/16 UNC GR DEFLECTOR BRACKET ASSEMBLY (INCL. 0,5,6,36) C156 BOLT-WHIZ 1/4 X 1 UNC GR C000 NUT-WHIZ FLG 1/4 UNC GR MANUAL STORAGE - CUSTOM PAK REAR BODY GUARD GUARD BACK MAIN DRIVE WELDMENT GUARD FRONT MAIN BALANCE WEIGHTS - 14GA - 3/4" RIVET-MONOBOLT C140 BOLT-WHIZ 1/4 X 1/ UNC GR TENSION LATCH CLAMP C035 NUT-FLG UNI-TRQ 3/8 UNC GR DEFLECTOR BRACKET 1

30 500 - PAGE 10 EXHAUST ASSEMBLY SERIAL BREAK DETAIL A SCALE 1 : DETAIL B SCALE 1 : 8

31 EXHAUST ASSEMBLY 500- PAGE 10A SERIAL BREAK NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # BODY COMPLETE WELDMENT EXHAUST LATCH FOLDED EXHAUST FOAM - LARGE EXHAUST FOAM - SMALL PERFORATED FOLDING WELD SILENCER SHELL WELD C494 BOLT-WHIZ 3/8 X 3/4 UNC GR C035 NUT-WHIZ FLG 3/8 UNC GR BRACKET - HOOD FASTENER STRAP - HOOD FASTENER C035 NUT NY-LOCK 3/8 UNC GR C40 BOLT-HEX 5/16 X UNC GR C344 BOLT-WHIZ 5/16 X 3/4 UNC GR C00 NUT-WHIZ FLG 5/16 UNC GR C0313 NUT-LOCK FLG UNI-TRQ 5/16 UNC GR NEOPRENE 1/4 X 1 3.5' C000 NUT-WHIZ FLG 1/4 UNC GR C35 BOLT-WHIZ 5/16 X 1 UNC GR C156 BOLT-WHIZ 1/4 X 1 UNC R TENSION ADJUSTER - DUMP EXHAUST LID DUMP LID SPRING WETHERSTRIP 1/4 X 5/ C008 NUT NY-LOCK #10-4 UNC GR C104 NUT-WHIZ FLG # C104 BOLT-WHIZ #10-4 X 3/ COMPLETE SILENCER (INCL.3-8,14,16-6,9) C650 BLT-HEX 3/8 X 6 1/ UNC GR EXHAUST RUBBER HANDLE 1

32 500 - PAGE 10-1 ROUND EXHAUST ASSEMBLY SERIAL BREAK

33 500 ROUND EXHAUST ASSEMBLY 500- PAGE 10-1A SERIAL BREAK NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # BODY COMPLETE WELDMENT C035 NUT-LOCK UNI-TRQ 3/8 UNC C494 BOLT-WHIZ 3/8 X 3/4 UNC GR C035 NUT-WHIZ FLG 3/8 UNC GR C000 NUT-WHIZ FLG 1/4 UNC GR PIN-LOCK 1/4 X 1 3/ RIVET-MONOBOLT EXHAUST LID HINGE RIGHT EXHAUST LID HINGE LEFT ROUND EXHAUST LID C156 BOLT-HX 1/4 X 1 UNC GR ROUND SILENCER SHELL PERFORATED ROUND SILENCER LATCH - TOGGLE DTL-00B EXHAUST LATCH PLATE BALANCE WEIGHTS - 14GA - 1/" LATCH - STRIKE DTL C00 NUT-WHIZ FLG 5/16 UNC GR ROUND EXHAUST FOAM NEOPRENE 1/8 X 1 3.5' C344 BOLT-WHIZ 5/16 X 3/4 UNC GR C104 BOLT-WHIZ #19-4-3/ C008 NUT NY-LOCK 10-4 UNC C104 NUT-WHIZ FLG # WETHERSTRIP 1/4 X 5/ C000 NUT NY-LOCK 1/4 UNC GR DUMP LID SPRING C148 BOLT-WHIZ 1/4 X 3/4 UNC GR C650 BOLT-HX 3/8 X 6 1/ UNC GR COMPLETE SILENCER ROUND (INCL. #-9,31) EXHAUST LID ASSEMBLY (INCL. #7,8,9,10)

34 500 - PAGE 10- ROUND EXTENSION EXHAUST SERIAL BREAK

35 ROUND EXTENSION EXHAUST 500- PAGE 10-A SERIAL BREAK 950+ NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # BODY COMPLETE WELDMENT EXHAUST SUB-ASSY (INCL. 4-14,,3) EXHAUST TRANSITION COMPLETE (INCL ) EXHAUST EXTENSION - WELD ROUND LID ASSEMBLY C148 BOLT-HEX 1/4 X 3/4 UNC GR C05 NUT-LOCK UNI-TRQ 1/4 UNC GR C00 NUT NY-LOCK 5/16 UNC GR HOSE CLAMP ADJUSTMENT CLAMP-UNIVERSAL BENT PINS HITCH CLIP B PIN CLEVIS B RIVET SHALLOW TUB RVT SEAL WITH HOLES EXHAUST TRANSITION - WELD C140 BOLT-WHIZ 1/4 X 1/ UNC GR TENSION LATCH CLAMP C000 NUT-WHIZ FLG 1/4 UNC GR NEOPRENE 1/4 X 1 3.5' C650 BOLT-HEX 3/8 X 6 1/ UNC GR C035 NUT-LOCK UNI-TRQ 3/8 UNC GR C550 BOLT-SKT HEAD 1/4 X 1/ S.S C50 NUT-LOCK FLG UNI-TRQ 1/4 UNC GR EXTENSION EXHAUST ASSEMBLY (INCL.ASSEMBLIES,3) 1

36 500 - PAGE 11 AUGER DRIVE PTO SECTION

37 500 AUGER DRIVE PTO SECTION 500- PAGE 11A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # BODY COMPLETE WELDMENT FLANGETTE-PF-07 MS BRG-AEL /8" BORE PLATE-BEARING MOUNT SPRKT BORE KEY 5/16 X 5/16 X 1/ KEY 5/16 X 5/16 X 4 1/ MAIN DRIVE SHAFT PULLEY DRIVE "B" DB (INCL. 10-1) PULLEY DRIVE "B" DB C481 SETSCR-HX SKT 3/8 X 1/ C48 SETSCR-HX SKT 3/8 X 3/ MALE HALF SHAFT FEMALE HALF SHAFT METER MOUNT BRACKET SENSOR MOUNT BRACKET C544 BOLT-WHIZ 3/8 X 3 FULL THREAD RUBBER GROMMET RB BONDED SEALING WASHER SENDEC METER MAGNET - SPARE PART ELASTO-PROXY # FC8-01-FM TACH-SENDEC HOUR METER C035 NUT-WHIZ FLG 3/8 UNC GR C494 BOLT-WHIZ 3/8 X 3/4 UNC GR C33 SETSCR-HX SKT 5/16 X 3/ C00 NUT-JAM HEX 5/16 UNC GR C35 SET SCREW-SQUARE HEAD 5/16 X C000 NUT-WHIZ FLG 1/4 UNC GR. 5 9 M5 NUT SUPPLIED WITH SENDEC METER C35 BOLT-CARR 1/4 X 3/4 GR F75 SCREW-MACHINE #6-3 X 3/ F063 NUT-MACHINE #6-3

38 500 - PAGE 1 AUGER DRIVE GEARBOX SECTION A A

39 500 AUGER DRIVE GEARBOX SECTION 500- PAGE 1A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # GEARBOX CHAIN GUARD WELD MACHINE SPROCKET /8 HUB ( TAPPED HOLE FOR GREASE ZERK ) A /8 HUB KEY 5/16 X 5/16 X 1 3/ MOUNT SPACER SPROCKET IDLER 06011F SPACER IDLER ARM IDLER CHAIN SPRING GEARBOX-GKN GRAIN VAC 1: C90 BLT-CARR 1/ X UNC GR GUARD MOUNT BOLT - WELD SNAPRING-EXT " DIA C180 BOLT - HEX 1/4 X 1 3/4 UNC GR CONNECTOR LINK #60 SINGLE AUGER DRIVE CHAIN (C/W PART #15) SHEAR SPROCKET ASSEMBLY (INCL,3,13,14,5) A SHEAR SPROCKET ASSEMBLY (INCL,3,13,14,0,5) MC40 BOLT-WHIZ 10MM X 5MM X 1.5P C148 BOLT-WHIZ 1/4 X 3/4 UNC GR GREASE ZERK - 1/4-8 STRAIGHT GEARBOX GUARD STOP C060 NUT-HEX 1/ UNC PLTD GR WASHER - LOCK 1/ DIA PLTD WASHER FLAT 1/ DIA USS C000 NUT NY-LOCK 1/4 UNC GR C000 NUT-WHIZ FLG 1/4 UNC GR C90 BOLT-HEX 1/ X UNC GR SHEARBOLT KIT (INCL.10PCS OF PART #14,5) 1

40 500 - PAGE 13 AUGER DRIVE AUGER SECTION

41 500 AUGER DRIVE AUGER SECTION 500- PAGE 13A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # BODY COMPLETE WELDMENT KEY 5/16 X 5/16 X 1 3/ KEY 1/4 X 1/4 X 1 3/ FLANGETTE-PF-05 MS BRG BALL YAR F SKF ST SECTION FLYTING C33 SETSCR-HX SKT 5/16 X 3/ C48 SETSCR-HX SKT 3/8 X 3/ C035 NUT-WHIZ FLG 3/8 UNC GR C494 BOLT-CARR 3/8 X 3/4 UNC GR CHAIN-COUPLER COUPLER SPROCKET 1 3/8 BORE COUPLER SPROCKET 1 1/4 BORE /8 COUPLER SPROCKET ASSEMBLY (INCL. #7,8,11,1,13) 1

42 500 - PAGE 14 REAR PULLEY DRIVE NOTE: BUSHING COMES COMPLETE WITH 3 BOLTS (1/-13 X 3/4" HEX) & 3 LOCKWASHERS.

43 500 REAR PULLEY DRIVE 500- PAGE 14A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # WELDMENT GUARD FRONT MAIN MAIN DRIVE SHAFT GROOVE, 3V, 5" OD "E" BSHG BSHG-QD E 1 3/ BRG - UELFU POWER SHAFT BEARING MOUNT KEY 5/16 X 5/16 X 1/ C494 BOLT-WHIZ 3/8 X 3/4 UNC GR C035 NUT-WHIZ FLG 3/8 UNC GR WASHER - LOCK 1/ DIA PLTD C060 NUT-HEX 1/ UNC PLTD GR BELT 6R-3VX110 BAND 1

44 500 - PAGE 15 FAN DRIVE REV. JULY 1/ NOTE: DO NOT REMOVE PART #39 AFTER ASSEMBLED DUE TO REALIGNMENT 1 1A /16" x " BOLTS COMPLETE WITH SHEAVE 13

45 500 FAN DRIVE 500- PAGE 15A REV. JAN /07 NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # ROTOR - GV BALANCED 1 1A ROTOR-GV ( POWDERCOATED ) COVER PLATE - FAN C518 BOLT-HX 3/8 X 1 1/ GR WASHER-LOCK 3/8 FEDALLOY BSHG-SPLIT TPR Q1 1 3/ SHAFT - ROTOR KEY 5/16 X 5/16 X 1/ C035 NUT-WHIZ FLG 3/8 UNC GR WASHER FLAT 3/8 DIA USS C035 NUT-HEX 3/8 UNC GR C510 BLT-HX 3/8 X 1 1/4 UNC GR PLATE - IDLER MOUNT LOCKCOLLAR SC SHEAVE 3V 6 GROOVE BSHG - QD SK 1 3/ C546 BOLT-HEX 3/8 X 3/4 UNC GR WELDMENT - IDLER FORK GREASE ZERK - 1/4-8 STRAIGHT C035 NUT NY-LOCK 3/8 UNC GR C060 NUT-HEX 1/ UNC GR DECAL - DO NOT REMOVE DECAL - MISSING GUARD HAZARD C904 BLT-HX 1/ X 1 1/ UNC GR F134 SETSCREW-SKT 1/4-8 X 5/16 CUP POINT BRG - UELFU WASHER-LOCK 1/ DIA PLTD C50 BOLT-HEX 3/8 X 1 UNC GR SPACING-BUSHING-IDLER WELDMENT - T - ADJUSTMENT TENSION BRACKET C968 BOLT-HEX 1/ X 5 UNC GR PULLY IDLER SPRING BRASS - FLANGED BUSHING DECAL - IDLER SPRING TENSION IDLER ASSEMBLY (INCL. 17,18,0,6,8-35) ROTOR MOUNT ASSEMBLY (INCL. 1-8,0-7,38,39,41) SNAP RING R GUIDE BEARING MOUNT C035 NUT-LOCK FLG UNI-TRQ 3/8 UNC C035 NUT-LOCK UNI-TRQ 3/8 UNC WASHER-FLAT 1/" DIA. USS 1

46 500 - PAGE 16 DRUM ASSEMBLY

47 500 DRUM ASSEMBLY PAGE 16A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # KEY 1/4 X 1/4 1 3/ SNAPRING-EXT 1 DIA C00 NUT-WHIZ FLG 5/16 UNC GR CUT-OFF AIR BRG-BALL SB05-16RKG FLANGETTE-PF-05 MS C344 BOLT-WHIZ 5/16 X 3/4 UNC GR DRUM SCREEN WELDMENT DRUM SHAFT CENTER WELDMENT C5 BOLT-WHIZ 1/4 X UNC GR C000 NUT NY-LOCK 1/4 UNC GR DRUM ASSEMBLY (INCL. 1-1) 1

48 500 - PAGE 17 INLET ASSEMBLY REV. AUG / DETAIL TACH-METER SCALE 1 : SERIAL BREAK

49 500 INLET ASSEMBLY PAGE 17A REV. FEB 0/09 NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # BODY COMPLETE WELDMENT MAIN DRIVING SHAFT PULLEY-IDLER-BCF P IDLER ARM WELDMENT SPACER-IDLER-DRUM IDLER SPRING KEY 1/4 X 1/4 X 1 3/ WASHER-FLAT 1/ DIA USS C060 NUT-HEX 1/ UNC PLT GR WASHER - LOCK 1/ DIA PLT C90 BLT-HEX 1/ X UNC GR C035 NUT-WHIZ FLG 3/8 UNC GR BELT "V" BX FLANGETTE-PF-05 MS BRG-BALL AEL INSERT RADIAL DRUM COVER PLATE WELDMENT STRAIGHT INLET WELDMENT SPONGE - 1 X 7/8 X 33 1/ SNAPRING-EXT 1" DRUM ASSEMBLY C035 NUT-WHIZ LARGE FLG 3/8 UNC GR C00 NUT-WHIZ FLG 5/16 UNC GR GREASE ZERK - 1/4-DRV STR DRUM IDLER ASSEMBLY (INCL 3-5,8-11,3) TACH CONNECTION INNER - WELD TACH CONNECTION OUTER - WELD SENDEC MAGNET FLAT TACH - SENDEC HOUR METER C148 BOLT-WHIZ 1/4 X 3/4 UNC GR C369 BOLT-WHIZ 5/16 X 1 1/ UNC GR C0313 NUT-LOCK FLG UNI-TRQ 5/16 UNC GR C000 NUT-WHIZ FLG 1/4 UNC GR F75 SCREW-MACHINE #6-3 X 3/ F063 NUT-MACHINE # BONDED SEALING WASHER REM TACH-METER KIT (INCL.5-35) PULLY - DRIVE - "B"DB C50 SETSCREW SQ HEAD 3/8 X 1 1/ C035 NUT-HEX 3/8 UNC GR PULLEY DB-7501 (INCL ) PULLEY #DB C481 SETSCREW-HX SKT 3/8 X 1/ C48 SETSCREW-HX SKT 3/8 X 3/ PULLY-DRIVE "B" DB (INCL ) STRAIGHT INLET SEAL KIT (INCL. PCS OF PART #18) STRAIGHT INLET ASSEMBLY (INCL. 16,17 & PCS OF 18) KEY 5/16" X 5/16" X 4 1/4" 1

50 500 - PAGE 18 LOWER SECTION AUGER ASSEMBLY-SPRING ASSIST

51 500 LOWER SECTION AUGER ASSEMBLY S/A PAGE 18A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # FLYTING - LOW HD AUGER 69 3/8" C050 NUT-WHIZ FLG 7/16 UNC GR C675 BOLT-WHIZ 7/16 X 1 UNC GR " X 9" REFLECTOR TAPE - RED ANCHOR ADJUSTMENT ASSEMBLY LEFT AUGER LATCH SPRING RIGHT AUGER LATCH SPRING HITCH-PIN - 3/3 X 1 3/ C050 NUT-JAM 7/16 UNC GR WASHER-FLAT 5/16 DIA USS C388 BOLT-HEX 5/16 X 1/4 UNC GR FIRST AUGER TUBE WELDMENT LOWER AUGER LATCH C7658 BOLT-SKT HEAD 7/16 X 5/8 BLACK LATCH MOUNT C00 NUT NY-LOCK 5/16 UNC GR PIN-CLEVIS 5/16 X 1 7/ PIN-LOCK 1/4 X 1/ LOWER AUGER ASSEMBLY (INCL. 5-18) AUGER LATCH ASSEMBLY (INCL.5-11,13-18) 1

52 500 - PAGE 19 MIDDLE SECTION AUGER ASSEMBLY-SPRING ASSIST REV. JUL 06/ A DETAIL A SCALE 1 : 4 34

53 MIDDLE SECTION AUGER ASSEMBLY S/A PAGE 19A REV. JUL 06/09 NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # FLYTING - MIDDLE HD AUGER 8 3/ WELD - AUGER - SECOND SECTION BEARING SUPPORT LEG /16 SPRING STEEL PIN WELDMENT - CONNECT HUB ADJUSTABLE LEVER ARM CENTER BEARING SUPPORT KIT (INCL. 3, 7, 9, 49 & 50) WELDMENT - LEVER ARM WELDMENT HINGE PIN PIN LEVER ARMS ADJUSTMENT WASHER WELDMENT STRIKER PLATE FRONT SAFTEY LATCH LINKAGE SAFTEY LATCH BRACKET LATCH-SAFTEY YOKE-CLEVIS B PIN-CLEVIS B PIN-ROLL 3/16 X PINS-COTTER 3/3 X 1/ PIN CLEVIS # HITCH PIN - SN #B C344 BOLT-WHIZ 5/16 X 3/4 UNC GR C550 BOLT-HEX 3/8 X 3 UNC GR C0515 BOLT-WHIZ 1/ X 1 1/ UNC GR C188 BOLT-HEX 1/4 X UNC GR PIN-ROLL 3/3 X 3/ C148 BOLT-HEX 1/4 X 3/4 UNC GR C3135 BOLT-HEX 5/16 X 3 1/ UNC GR " X 9" REFLECTOR TAPE - AMBER AUGER SPRING GV AUGER HANDLE SPRING AUGER ASSIST SPRING-LARGE AUGER ASSIST SPRING-SMALL STOP SPACER CLEVIS WELDMENT TOP SPRING SPONGE-F CELL ADHESIVE BACK CLEVIS WELDMENT BOTTOM LEFT CLEVIS WELDMENT BOTTOM RIGHT C936 BOLT-HEX 1/ X 3 UNC GR C060 NUT NY-LOCK 1/ UNC GR C546 BOLT-HEX 3/8 X 3/4 UNC GR WASHER-LOCK 1/ DIA C060 NUT-HEX 1/ UNC GR C035 NUT NY-LOCK 3/8 UNC GR C00 NUT-WHIZ FLG 5/16 UNC GR WASHER-FLAT 1/4 DIA USS BRG-BALL UC05-100DI WASHER-LOCK 5/16 DIA WASHER-FLAT 3/8 DIA USS GREASE ZERK - 1/4-8 STRAIGHT C000 NUT NY-LOCK 1/4 UNC GR PIN=-HINGE-UPPER PINS-COTTER 3/16 X 1 1/ CLEVIS ASSEMBLY BOTTOM RIGHT CLEVIS ASSEMBLY BOTTOM LEFT

54 500 - PAGE 0 UPPER SECTION AUGER ASSEMBLY-SPRING ASSIST SERIAL BREAK

55 UPPER SECTION AUGER ASSEMBLY - S/A PAGE 0A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # WELDMENT-AUGER THIRD SECTION END DUMP TUBE WELDMENT RD SEC. S/A FULL LENGTH HARD SURFACING-7 1/" HIGH TENSILE END DUMP WELDMENT FLANGETTE PFL06-BLACK BRG-BALL UC END DUMP SPOUT AUGER LATCH MOUNT WELD DUST COLLECTOR HANDLE PIPE & LINKAGE WELD GV WELDMENT-LINKAGE LATCH-ANCHOR AUGER SPRING GV AUGER ALIGNMENT PIN WELDMENT- UPPER AUGER LATCH ANCHOR ADJUSTMENT ASSEMBLY LATCH MOUNT C035 NUT-WHIZ FLG 3/8 UNC GR C50 BOLT-WHIZ 3/8 X 1 UNC GR C035 NUT NY-LOCK 3/8 UNC GR PINS-COTTER 1/8 X C388 BOLT-HEX 5/16 X 1/4 UNC GR C00 NUT NY-LOCK 5/16 UNC GR C050 NUT-JAM HEX 7/16 UNC GR C494 BOLT-WHIZ 3/8 X 3/4 UNC GR C518 BOLT-WHIZ 3/8 X 1 1/ UNC GR C369 BOLT-WHIZ 5/16 X 1 1/ UNC GR C035 NUT-LOCK FLG UNI-TRQ 3/8 UNC GR BOLT-TEK 1/4-14 X WASHER-FLAT 5/16 DIA USS WASHER-FLAT 1/4 DIA USS PIN-LOCK 1/4 X 1/ C501 BOLT-CARR 3/8 X 1 UNC GR STRIKER PLATE WELDMENT C344 BOLT-WHIZ 5/16 X 3/4 UNC GR C00 NUT-WHIZ 5/16 UNC GR SPRING ARM DUMP LID SPRING PIN-CLEVIS 5/16 X 1 7/ HITCH PIN 3/3 X 1 3/ PIN-CLEVIS B HITCH PIN SN #B WASHER-FLAT 3/8 DIA SAE 4

56 500 - PAGE 0-1 UPPER SECTION AUGER ASSEMBLY-SPRING ASSIST SERIAL BREAK A

57 UPPER SECTION AUGER ASSEMBLY - S/A PAGE 0-1A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # RD AUGER TUBE WELD FLYTING - UPPER HD-HYD LIFT LATCH MOUNT STRIKER PLATE WELDMENT C7658 BOLT-SKT HEAD 7/16 X 5/8 UNC GR.5 BLACK RD AUGER S/A HANDLE WELDMENT - LOWER AUGER LATCH ANCHOR ADJUSTMENT ASSEMBLY C494 BOLT-HEX 3/8 X 3/4 UNC GR C510 BOLT-HEX 3/8 X 1 1/4 UNC GR C035 NUT-WHIZ FLG 3/8 UNC GR C050 NUT-JAM HEX 7/16 UNC GR " X 9" REFLECTOR TAPE - RED C344 BOLT-WHIZ 5/16 X 3/4 UNC GR C00 NUT-WHIZ 5/16 UNC GR RIGHT AUGER LATCH SPRING LEFT AUGER LATCH SPRING PIN-CLEVIS 5/16 X 1 7/ HITCH PIN 3/3 X 1 3/ WASHER-FLAT 5/16 DIA USS C388 BOLT-HEX 5/16 X 1/4 UNC GR C00 NUT NY-LOCK 5/16 UNC GR ST-6009 BOLT-TEK #10-16 X 1/ DUMP LID SPRING C344 BOLT-CARR 5/16 X 3/4 UNC GR BOLT-TEK #10-16 X 3/ WASHER-FLAT 1/4 DIA USS TENSION ADJUSTER - DUMP SPRING ARM C501 BOLT-CARR 3/8 X 1 UNC GR FLANGETTE PFL06-BLACK BRG-BALL UC06-104D1LLJ C035 NUT NY-LOCK 3/8 UNC GR END DUMP LINER KIT (INCL. POLY LINER & HARDWARE) SPOUT - 3/16 X17 BELTING ENDDUMP-BOT STYLE-WELD SMALL DUMP LID - WELD LARGE DUMP LID - WELD C630 BOLT-HEX 3/8 X 10 UNC GR ENDDUMP-BOT STYLE- ASSY (INCL. 3-39) 1 40A ENDDUMP & HARDWARE (INCL. 3,33,34,36-39) AUGER LATCH ASSEMBLY (INCL. 3,5,7,8,1,16-) C035 NUT-LOCK FLG UNI-TRQ 3/8 UNC GR END DUMP SPRING 1

58 500 - PAGE 1 LOWER AND MIDDLE AUGER ASSEMBLY

59 500 LOWER AND MIDDLE AUGER ASSEMBLY - HYDRAULIC PAGE 1A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # FLYT-MID HD AUGER 8 3/ C344 BOLT-WHIZ 5/16 X 3/4 UNC GR MIDDLE AUGER TUBE UPPER CYLINDER ARM LOWER LIFT ARM LIFT PIN C00 NUT-WHIZ FLG 5/16 UNC GR GREASE ZERK - 1/4-DRV STR WELDMENT CONNECT HUB WELDMENT CENTER BEARING SUPPORT BEARING SUPPORT LEG BRG-BALL UC05-100DI WASHER FLAT 5/16 DIA USS WASHER-LOCK 5/16 DIA PLT C3135 BOLT-HEX 5/16 X 3 1/ UNC GR /16 SPRING STEEL PIN LOWER AUGER TUBE SPONGE- F CELL ADHESIVE BACK C35 BOLT-WHIZ 5/16 X 1 UNC GR LOWER PIVOT SHAFT C00 NUT NY-LOCK 5/16 UNC GR DECAL - HIGH PRESSURE FLUID GREASE PIN WELD C384 BOLT-HX 5/16 X UNC GR FLYT-LOW HD AUGER 69 3/ MIDDLE AUGER ASSEMBLY ( INCL. 1-16) 1

60 500 - PAGE UPPER AUGER ASSEMBLY HYDRAULIC A

61 UPPER AUGER ASSEMBLY PAGE A HYDRAULIC LIFT REV. APR 03/08 NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # FLYTING-UPPER HD-HYD LIFT UPPER LIFT ARM WELD UPPER AUGER TUBE WELD " X 9" REFLECTOR TAPE-RED LIFT PIN GREASE ZERK - 1/4-DRV STR C035 NUT-WHIZ FLG 3/8 UNC GR C494 BLT-HX 3/8 X 3/4 UNC GR BOLT-TEK #10-16 X 3/ WASHER-FLAT 1/4 DIS USS FLANGETTE PFL06-BLACK BRG-BALL UC06-104D1LLJ C035 NUT NY-LOCK 3/8 UNC GR LINER - DUMPER SPOUT - 3/16 X 17 BELTING C501 BLT-CARR 3/8 X 1 UNC GR C630 BLT-HX 3/8 X 10 UNC GR DUMP LID SPRING C344 BLT-CARR 5/16 X 3/4 UNC GR C00 NUT-WHIZ FLG 5/16 UNC GR TENSION ADJUSTER - DUMP SPRING ARM END DUMP SPRING ENDDUMP-BOT STYLE-WELD SMALL DUMP LID-WELD LARGE DUMP LID-WELD AUGER STOP WELD C50 BOLT-WHIZ 3/8 X 1 UNC GR ENDDUMP-BOT STYLE-ASSY (INCL.9-1,14-6,31,3) 1 9A ENDDUMP TUBE AND HARDWARE (INCL. 13,14,17,4-6,3) C344 BOLT-WHIZ 5/16 X 3/4 UNC GR C035 NUT-FLG UNI-TRQ 3/8 UNC GR ST6009 BOLT-TEK #10-16 X 1/ 4

62 500 - PAGE 3 HYDRAULIC HOSE AND CYLINDER ASSEMBLY ***NOTE: HYDRAULIC CYLINDERS (PARTS #0 & 1) COME COMPLETE WITH PINS.

63 HYDRAULIC HOSE AND CYLINDER ASSEMBLY PAGE 3A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # FB COUPLER -PIONEER /8 BALL VALVE FP BOTH ENDS TEE -6MJIC-6MJIC-6FJICX TEE -6MJIC-6MJIC-6MJIC MB ORB - 6MP ADAPTER /8 RESTRICTOR-6MJIC-6MP (1/3" HOLE) ADAPTER 8MB-8FJICX ADAPTER 6FJIC-8MJIC /8 HOSE 135" 8MP-6FJIC MP-6MJIC 90 DEGREE ELBOW /8 RESTRICTOR 6MJIC-6MJIC (1/3" HOLE) /8 HOSE 90" 6FJIC-6FJIC /8 HOSE 74" 6FJIC-6FJIC ADAPTER 6MJIC-8MP RESTRICTOR 6MJIC-8MP (1/3" HOLE) /8 HOSE 8 1/4" 6FJICX90-6FJICX /8 HOSE 5" 6FJICX-6FJICX HYDRAULIC KIT (INCL. #1-17) SINGLE SEQUENCE VALVE 8FB PORTS CYL. 1/ X 10 1/4 X 1 1/ CYL. 3 1/ X 10 X 1 1/ HYD. LIFT SUB ASSY (INCL. 18-1) HYD. HOSE CLIP PLATE-VALVE C00 NUT-WHIZ FLG 5/16 UNC GR C000 NUT-WHIZ FLG 1/4 UNC GR C19 BLT-HX 1/4 X 1/4 UNC GR.5

64 500 - PAGE 4 STANDARD HOSES " X 9" STAINLESS STEEL FLEX HOSE " X 81" STAINLESS STEEL FLEX HOSE " X 81" BASKETWEAVE HOSE " X 87" ALUMINUM " X 54" ALUMINUM FLOOR SWEEP ASSY 7 6

65 500 STANDARD HOSE CONFIGURATIONS PAGE 4A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # HOSE RING HOSE-STEEL STNLSS 7" X 81" RIVET - SHALLOW TUB RVT " S. STEEL HOSE COMP. (INCL. 1-3,38) " ALUMINUM PIPE RIVET - SHALLOW TUB RVT " X 87" ALUM. PIPE (INCL. 5,6,37) " ALUMINUM PIPE " X 54" ALUM. PIPE COMP. (INCL. 6,9,37) HOSE - STEEL STNLSS 7" X 9" " X 9" S.STL HOSE COMP. (INCL. 1,3,10,38) ALUM - LOAD-OUT TUBE SLIDING DOOR WELDMENT HANDLE BENT ALUM - BIN LOAD-OUT ASSY (INCL. 1-14,31-34) PINS-COTTER 3/3 X 1/ CLEVIS 1/4 X 1 17/3 - SN #B CLAMP - UNIVERSAL RIVET - SHALLOW TUBULAR - SN #RVT HOSE CLAMP ADJUSTMENT C00 NUT NY-LOCK 5/16 UNC GR CLAMP - HOSE 8" HAS FLOOR SWEEP - ASSY (INCL. 4-30,3,34) FLOOR SWEEP WEAR STRIP SWEEP FLAT HANDLE FLOOR SWEEP TUBE ALUMINUM RIVET - MONOBOLT STANDING FLOOR HANDLE PIN - LYNCH 1/4 X 1 1/ RUBBER HANDLE GRIPS WASHER - FLAT 1/4 DIA USS C000 NUT NY-LOCK 1/4 UNC GR C575 BLT-TRUSS 1/4 X 3/4 UNC C35 BOLT-CARR 1/4 X 3/4 UNC GR HOSE 7" X 80" BASKETWEAVE " BASKETWEAVE HOSE ASSY (INCL.1,,35,38) " HOSE END COMPLETE(INCL.16-1) UPDATED 7" BELL CLAMP (INCL.16-1) 3

66 500 - PAGE 5 FLOOR SWEEP 7" STANDING FLOOR SWEEP " FLOOR SWEEP OPTION

67 FLOOR SWEEP OPTIONS 7" FLOOR SWEEP PAGE 5A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # FLOOR SWEEP TUBE ALUMINUM STANDING FLOOR HANDLE PIN-LYNCH 1/4 X 1 1/ RUBBER HANDLE GRIPS C35 BOLT-CARR 1/4 X 3/4 UNC GR C000 NUT NY-LOCK 1/4 UNC GR SWEEP FLAT HANDLE FLOOR SWEEP WEAR STRIP RIVET - MONOBOLT STANDING FLOOR SWEEP ASSY (INCL.1-9) STANDING FLOOR SWEEP KIT (INCL.,3,4) FLOOR SWEEP ASSY (INCL. 1,5,9) " FLOORSWEEP WEARSTRIP KIT (INCL. 8,9) 1 6" FLOOR SWEEP NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # " STANDING SWEEP TUBE STANDING FLOOR HANDLE PIN-LYNCH 1/4 X 1 1/ RUBBER HANDLE GRIPS " SWEEP FLAT HANDLE RIVET - MONOBOLT " STANDING FLOOR SWEEP ASSY (INCL. 14-3) C35 BOLT-CARR 1/4 X 3/4 UNC GR C000 NUT NY-LOCK 1/4 UNC GR " FLOORSWEEP WEARSTRIP KIT (INCL.19,4) FLOOR SWEEP WEAR STRIP FLOOR SWEEP ASSY 6" (INCL.14,18,19,1,,4) 1

68 500 - PAGE 6 TELESCOPING TUBE OPTIONS FT TELESCOPING TUBE (COLLASPED LENGTH) FT TELESCOPING TUBE (COLLASPED LENGTH)

69 500 TELESCOPING TUBE OPTIONS PAGE 6A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # TELESCOPING LOADOUT NOZZLE (INCL. 3,4) TELESCOPING LOADOUT - 8FT (INCL. 5,6) TELESCOPING END ASSEMBLY (INCL. 7-11) LOADOUT NOZZLE SUB ASSY (INCL. 8,1-15) TELESCOPING END ASSY (INCL. 7,8,10,11,17) TELESCOPING SUB ASSY 8FT (INCL. 8,13-15) " HOSE END COMPLETE RIVET - SHALLOW TUB RVT SLIDE TUBE C1438 SCREW-MACHINE 1/4 X 3/ C000 NUT NY-LOCK 1/4 UNC GR END TUBE WELDMENT " HOSE CLAMP BAND COMPLETE SEAL - CUT RING RIVET-MONOBOLT END TUBE WELDMENT SLIDE TUBE 1

70 500 - PAGE 7 TRANSITIONS TRANSITION - 6" MALE TO 7" FEMALE TRANSITION - 7" MALE TO 6" FEMALE TRANSITION - 7" MALE TO 8" FEMALE TRANSITION - 8" MALE TO 7" FEMALE

71 500 TRANSITIONS PAGE 7A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # "M - 7"F REDUCER ASSEMBLY CLAMP - UNIVERSAL HOSE CLAMP ADJUSTMENT "M - 7"F REDUCER WELD C00 NUT NY-LOCK 5/16 UNC GR RIVET - SHALLOW TUBULAR - SN #RVT CLEVIS 1/4 X 1 17/3 - SN #B PINS-COTTER 3/3 X 1/ "F - 7"M REDUCER FINAL ASSY (INCL.,3,5-8,10) "F - 7"M REDUCER WELD "M - 8"F REDUCER (INCL.,3,5-8,1) "M - 8"F REDUCER WELD "F - 8"M REDUCER WELD "F - 8"M REDUCER ASSY (INCL.,3,5-8,13) 1

72 500 - PAGE 8 6" HOSE CONFIGURATIONS A DETAIL A SCALE 1 : 6

73 6" HOSE CONFIGURATIONS PAGE 8A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # " X 7" STL HOSE COMPLETE (INCL. -5) RIVET - SHALLOW TUB RVT HOSE STEEL FLEX 6" X 7" " HOSE END HOSECLAMP 6" (INCL. 9-15) " X 144" LIGHT RUBBER HOSE COMP. (INCL. 4,5,7,8) HOSE - 45MIL DURA 6" X 144" CLAMP HOSE 6 1/ HS BODY-HOSE CLAMP - 6" CLAMP UNIVERSAL RIVET - SHALLOW TUBULAR - SN #RVT CLEVIS - 1/4 X 1 17/3 - SN #B PINS-COTTER 3/3 X 1/ HOSE CLAMP ADJUSTMENT C00 NUT NY-LOCK 5/16 UNC GR.5 1

74 500 - PAGE 9 7" HOSE OPTIONS " X 10' STRAIGHT ALUMINUM PIPE " X 74" GLV. STL. FLEX HOSE GALV. HOSE(PT#6) ALSO SOLD SEPARATELY " X 150" GLV. STL. FLEX HOSE GALV. HOSE(PT#1) ALSO SOLD SEPARATELY 5

75 7" HOSE OPTIONS PAGE 9A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # HOSE-GLVN STEEL 7" X 150" UPDATED 7" BELL CLAMP TUBE 7" CHARCOAL RIVET - SHALLOW TUB RVT " X 150" GLV STL FLEX HOSE (INCL. 1-4) HOSE-GLVN STEEL 7" X 74" " X 74" GLV STL FLEX HOSE (INCL. -4,6) " ALUMINUM PIPE 10" RIVET - SHALLOW TUB RVT " HOSE END COMPLETE " X 10" ALUMINUM PIPE WITH ONE END (INCL. 8-10) 1

76 500 - PAGE 30 BASKETWEAVE AND NONBASKETWEAVE OPTIONS

77 BASKETWEAVE & NONBASKETWEAVE OPTIONS PAGE 30A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # HOSE 7" X 150" BASKETWEAVE UPDATED 7" BELL CLAMP HOSE RING CLAMP - HOSE 8" HAS HOSE 7" X 150" BASKETWEAVE (INCL. 1-4) " X 74" BLACK HOSE SLEEVE HOSE 7" X 74" NONBASKETWEAVE HOSE 7" X 74" NONBASKETWEAVE ASSY (INCL.-4,6,7) " X 150" BLACK HOSE SLEEVE HOSE 7" X 150" NONBASKETWEAVE HOSE 7"X 150" NONBASKETWEAVE ASSY(INCL.-4,9,10) HOSE 7" X 74" BASKETWEAVE " BASKETWEAVE HOSE ASSY (INCL. -4,1) 1

78

79 DRILL CLEANOUT HOSE (4") OPTIONS PAGE 31A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # " - 4" HOSE ADAPTER " HEAVY RUBBER HOSE (PER FOOT) " HOSE END " HOSE CLAMP HS " X 144" RUBBER HOSE COMPLETE (INCL. 1-4) " - 4" HOSE ADAPTER " X 144" HEAVY HOSE (INCL. -4,6) 1 DRILL CLEANOUT- IDEAL FOR HARD TO GET SPOTS, BUT HAS LIMITED CAPACITY

80 500 - PAGE 3 7" CHAMFERED CLEANUP NOZZLE OPTION EXISTING 1/" X 1 1/" WHIZ BOLT & 1/" FLG UNI-TRQ NUT

81 500 7" CLEANUP NOZZLE OPTION PAGE 3A REV. APR 4/07 NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # " CHAMFERED CLEAN UP NOZZLE NOZZLE SUPPORT PIPE ROLLER WHEELS WHEEL 6 X 1 1/ C56 BLT-HX 3/8 X 1 3/4 UNC GR C035 NUT NY-LOCK 3/8 UNC GR WASHER-FLAT 1/ DIA USS C060 NUT NY-LOCK 1/ UNC GR C180 BLT-HX 1/4 X 1 3/4 UNC GR C000 NUT NY-LOCK 1/4 UNC GR C405 BLT-HX 5/16 X 3 1/4 UNC GR C00 NUY NY-LOCK 5/16 UNC GR C16 BLT-HX 1/4 X 4 UNC GR WASHER-FLAT 1/4 DIA USS C148 BLT-HX 1/4 X 3/4 UNC GR C35 BLT-HX 5/16 X 1 UNC GR NOZZLE SPRING GV PLTD WASHER-FLAT 5/16 DIA USS PIN-LOCK 1/4 X 1 3/ HANDLE WELDMENT RUBBER HANDLE GRIPS WHEEL MOUNT WELD AIR INTAKE COVER PLATE " CLEAN UP GUIDE WELD " CHAMFERED NOZZLE ASSY (INCL. 1-4) C00 NUT-WHIZ FLG 5/16 UNC GR C35 BLT-WHIZ 5/16 X 1 UNC GR CLEAN UP UPPER MOUNT PIN-LOCK 1/4 X 1 3/ CLEAN UP LOWER MOUNT " CHAMFERED NOZZLE MOUNTING KIT 1

82 500 - PAGE 33 8" HOSE OPTIONS " X 76" STAINLESS STEEL FLEX HOSE 7 8" X 48" STAINLESS STEEL FLEX HOSE " X 54" ALUMINUM PIPE W/END " X 10" ALUMINUM PIPE W/END 19 0

83 8" HOSE OPTIONS PAGE 33A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # HOSE-STEEL STAINLESS 8" X 76" " HOSE RING " HOSE CLAMP COMPLETE (INCL.8-1,1,) RIVET - SHALLOW TUB RVT " X 76" S. STL HOSE COMP. (INCL. 1-4) HOSE-STEEL STAINLESS 8" X 48" " X 48" STAINLESS STL HOSE COMPLETE " CLAMP BAND & TUBE CLEVIS - 1/4 X 1 17/3 - SN #B HITCH PIN - SN #B CLAMP UNIVERSAL RIVET - SHALLOW TUBULAR - SN #RVT " X 54" ALUMINUM PIPE " HOSE CLAMP PLAIN COMP. (INCL. 9, 11, 1, 15, 17, 18, 1,) RIVET - SHALLOW TUBULAR - SN #RVT " X 54" ALUM PIPE W/ ONE HOSE END (INCL ) " HOSE CLAMP BAND PLAIN WELD PINS-COTTER 3/3 X 1/ " X 10" ALUMINUM PIPE " X 10" ALUM PIPE W/ ONE HOSE END (INCL. 14,15,19) HOSE CLAMP ADJUSTMENT C00 NUT NY-LOCK 5/16 UNC GR.5

84 500 - PAGE 34 EXHAUST AERATION & CONVERSION KITS 500 AERATION ATTACHMENT KIT EXHAUST CONVERSION KIT RECTANGLE TO 8" ROUND

85 EXHAUST AERATION & CONVERSION KITS PAGE 34A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # AERATION 90 DEG TO 8" ROUND C650 BLT-HX 3/8 X 6 1/ UNC GR C035 NUT NY-LOCK 3/8 UNC GR TENSION LATCH CLAMP C140 BOLT-WHIZ 1/4 X 1/ UNC GR C000 NUT-WHIZ FLG 1/4 UNC GR BODY COMPLETE WELDMENT NEOPRENE 1/4 X 1 3.5' AERATION ATTACHMENT KIT (INCL. 1-6,8) EXHAUST TRANSITION RECT TO 8" ROUND EXHAUST TRANSITION RECT TO 8" ROUND (INCL. 1-6,9) 1

86 500 - PAGE 35 FOUR HOSE EXTENSION KIT

87 FOUR HOSE EXTENSION KIT PAGE 35A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # FOUR HOSE EXTENSION WELD TIE DOWN RUBBER C396 BLT-HX 5/16 X 3/ WASHER-FLAT 5/16 DIA USS C00 NUT NY-LOCK 5/16 UNC GR PLASTIC PLUG - 1 1/4" SQUARE FOUR HOSE EXTENSION KIT (INCL. 1-6) 1

88

89 HIRED HAND KIT OPTION PAGE 36A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # JACK-SIDEWIND-CLEVIS ENDS HIRED HAND HOSE STRAP ASSEMBLY HIRED HAND PANEL SLEEVE TUBE PIVOT TUBE HIRED HAND TUBE HIRED HAND CONNECTION FLAT HANDLE BOLT TIEDOWN RUBBER/TARP STRAP C880 BOLT-HEX 1/ X 3/4 UNC GR C490 BOLT-HEX 1/ X 3 1/4 UNC GR C990 BOLT-HEX 1/ X 7 UNC GR C5375 BOLT-SHOULDER 1/ X 5/8 X 3/ C344 BOLT-WHIZ 5/16 X 3/4 UNC GR C00 NUT-WHIZ FLG 5/16 UNC GR C035 NUT-LOCK UNI-TRQ 3/8 UNC GR C0500 NUT-WHIZ FLG 1/ UNC GR C060 NUT NY-LOCK 1/ UNC GR HIRED HAND PIN PINS COTTER 3/16 X 1 1/ WASHER-FLAT 3/8 DIA SAE HIRED HAND OPTION KIT (INCL. 1-1) 1

90 500 - PAGE 37 DUST COLLECTOR OPTION 4 3 USE EXISTING EXHAUST HARDWARE (3/8 X 6 1/" HEX BOLT UNC & 3/8NYLOCK NUT UNC) TO ATTACH DUST COLLECTOR

91 DUST COLLECTOR OPTIONS PAGE 37A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # DUST COLLECTOR WELD END CAP WELDMENT C43 BLT-HX 5/16 X 5 UNC GR C00 NUT NY-LOCK 5/16 UNC GR C714 BLT-HX 7/16 X 1/ UNC GR WASHER-FLAT 7/16 DIA USS C050 NUT-WHIZ FLG 7/16 UNC GR BRACE WELD BRACE CLEVIS WELD PINS-HITCH CLIP CP-88H COLLECTOR BRACE ASSY (INCL. 8,9) COLLECTOR ASSY (INCL. 1-10) DUST BAG - GV CLAMP-HOSE 50MM-95MM DUST COLLECTOR BAG 500GV (INCL. 13,14) DC CONE COMBINATION NIPPLE " BALL VALVE HOSE-PVC " I.D BARREL-PLASTIC 45GAL CLAMP-HOSE HS DC CONE ASSY (INCL. 16-1,3,4) NEOPRENE 1/8 X 3/8 3.0' " STREET ELBOW 45 DEG DUST COLLECTOR- CATCHES MOST DUST TO HELP KEEP A CLEANER AIR EXHAUST, IF REQUIRED, AND A CLEANER WORK SITE. ***NOTE: WHEN PURCHASING THE DUST COLLECTOR - ( ) YOU MUST PURCHASE ONE OF THE COLLECTOR OPTIONS ( OR )

92

93 FINE DRUM SCREEN OPTION PAGE 38A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # DRUM FINE SCREEN C5 BOLT-WHIZ 1/4 X UNC GR C000 NUT NY-LOCK 1/4 UNC GR WELDMENT-CENTER FLANGETTE PF-05 MS C344 BOLT-WHIZ 5/16 X 3/4 UNC GR SB05-16RKG5 BEARING C00 NUT-WHIZ 5/16 UNC GR SHAFT - DRUM KEY AIR CUT-OFF DRUM FINE SCREEN ASSY (INCL. 1-11) 1

94

95 BRUSH KIT PAGE 39A REV. APR 7/07 NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # C035 NUT-WHIZ FLG 3/8 UNC GR BRUSH ATTACHMENT SUPPORT C164 BOLT-WHIZ 1/4 X 1 1/4 UNC GR C000 NUT-WHIZ FLG 1/4 UNC GR WASHER-FLAT 3/8 DIA USS IDLER CHAIN SPRING C035 NUT NY-LOCK 3/8 UNC GR BRUSH SUPPORT HINGE C50 BOLT-WHIZ 3/8 X 1 UNC GR C494 BOLT-WHIZ 3/8 X 3/4 UNC GR C518 BOLT-HX 3/8 X 1 1/ UNC GR.5 FULL THREAD BRUSH MOUNT BRACKET RIVET - MONOBOLT BRUSH HOLDER BRUSH BRUSH SUB ASSEMBLY (INCL.1-15) DRUM BRUSH KIT (INCL. 1-16) 1

96

97 LIGHT KIT OPTION PAGE 40A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # 1 CURB SIDE LIGHT 1 ROAD SIDE LIGHT 1 3 LICENSE PLATE HOLDER 1 4 CLEARANCE LIGHT 5 NUT WHIZ 1/4 UNC GV LIGHTING PACKAGE (INCL 1-5) CABLE TIE /4" ADAPTER - 4 FLAT TO 7 ROUND END LIGHT MOUNT RIGHT LIGHT MOUNT LEFT SCREW - TEK HX 1/4 X 3/ LIGHT KIT OPTION (INCL 6-11) 1 NOTE: ITEMS 1-5 ARE CONTAINED UNDER # (GV LIGHTING PACKAGE) NOTE: ALL PARTS LISTED IN PARTS LIST WILL BE PACKAGED ALONG WITH COMPONENTS SUPPLIED IN LIGHT KIT OPTION - FOR HIGHWAY TRAVEL AND NIGHTTIME SAFETY

98

99 SPOUT OPTION PAGE 41A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # " DISCHARGE SPOUT - 9" LONG TIE DOWN RUBBER-TARP STRAP SPOUT OPTION (INCL. 1,) SPOUT OPTION - HELPS KEEP GRAIN FROM BLOWING OUT ON SMALLER TRUCKS WHILE LOADING.

100 500 - PAGE 4 STUB UNLOADING AUGER KIT

101 STUB UNLOADING AUGER KIT PAGE 4A REV. APR 11/08 NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # END-DUMP - BOTTOM STYLE DUMP LID-SMALL DUMP LID-LARGE C630 BLT-HX 3/8 X 10 UNC GR C035 NUT NY-LOCK 3/8 UNC GR LINER - DUMPER SPOUT 3/16" X 17" BELTING C501 BLT-CARR 3/8 X 1 UNC GR FLANGETTE PFL06-BLACK BRG-BALL UC06-104D1LLJ BOLT-TEK #10-16 X 3/ WASHER-FLAT 1/4 DIA USS TENSION ADJUSTER - DUMP SPRING ARM DUMP LID SPRING C344 BLT-CARR 5/16 X 3/4 UNC GR C00 NUT-WHIZ FLG 5/16 UNC GR ENDDUMP - BOT STYLE - ASSY (INCL. 1-17,45,46) STUB UNLOADER AUGER STUB UNLOAD THIMBLE SPONGE-F CELL ADHESIVE BACK BRG-BALL UC05-100DI WELDMENT-CENTER BEARING SUPPORT BEARING SUPPORT LEG WELDMENT CONNECT HUB /16 SPRING STEEL PIN WASHER-FLAT 5/16 DIA USS C3135 BLT-HX 5/16 X 3 1/ UNC GR WASHER-LOCK 5/16 DIA PLTD C494 BLT-HX 3/8 X 3/4 UNC GR C035 NUT-WHIZ FLG 3/8 UNC GR C00 NUT NY-LOCK 5/16 UNC GR HITCH PIN - 3/3 X 1 3/ C388 BLT-HX 5/16 X 1/4 UNC GR LEFT AUGER LATCH SPRING PIN-CLEVIS 5/16 X 1 7/ RIGHT AUGER LATCH SPRING C050 NUT-JAM HEX 7/16 UNC GR LATCH MOUNT LOWER AUGER LATCH-LONG ANCHOR ADJUSTMENT ASSEMBLY C7658 BLT-SKT HD 7/16 X 5/8 UNC GR.5 - BLACK AUGER LATCH ASSEMBLY (INCL. 7,31-4) STUB UNLOADING KIT (INCL. 1-43,45,46) ST-6009 BOLT-TEK #10-16 X 1/ END DUMP SPRING 1 STUB UNLOADING KIT - A GOOD OPTION TO USE WHEN AUGER ON VAC CANNOT BE FULLY OPENED.

102 500 - PAGE 43 HYDRAULIC AUGER ANGLE INCLINER COMPLETE KIT NUMBER: INCLUDES PARTS 1-14 THE HYDRAULIC AUGER INCLINER WILL LIFT THE END OF THE AUGER VERTICALLY BY AS MUCH A 4". THE KIT REQUIRES HYDRAULIC TO OPERATE. IT MOUNTS ON THE GRAIN VAC AXLE (AUGER SIDE) WITH U-BOLTS. THE KIT INCLUDES ALL THE NECESARY PARTS AND PICTORIAL INSTRUCTIONS NOTE: KIT MUST BE MOUNTED AS FAR TO THE OUTSIDE AS POSSIBLE TO PREVENT HITCH DAMAGE.

103 HYDRAULIC AUGER ANGLE INCLINER PAGE 43A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # OUTER TUBE BASE INNER TUBE U-BOLT 5/8 X 5 X 6 1/ SQ UNC C7950 BOLT-HEX 1 X 5 1/ UNC GR C080 NUT-LOCK UNI-TRQ 5/8 UNC C0340 NUT - NY LOCK 1 UNC GR CYL - X /8 TIEROD RESTRICTOR 6MP-6FP 1/16" FB COUPLER - PIONEER F FR. DECAL - HYD. LIFT HAZARD DECAL - HYD. LIFT HAZARD C7954 BOLT - HEX 1 X 6 UNC GR / MP - 6MP

104 500 - PAGE 44 DUMPER EXTENSION CHUTE OPTION 3 REMOVE OLD HARDWARE 1 REMOVE OLD RUBBER COMPLETE KIT NUMBER: INCLUDES PARTS 1-3 THIS KIT ATTACHES TO THE VAC DUMPER. IT EXTENDS THE REACH OF THE VAC FURTHER TOWARDS THE MIDDLE OF THE TRUCK BY CHANGING THE DEFLECTION OF THE GRAIN. THE ANGLE OF THE DEFLECTION IS ALSO ADJUSTABLE. THE KIT INCLUDES ALL THE NECESSARY HARDWARE, PARTS AND INSTALLATION INSTRUCTIONS. IT REQUIRES ONLY TO REMOVE THE DUMPER RUBBER, DRILL 4 HOLES AND INSTALL CHUTE. (OPTIONAL) THE RUBBER MAY ALSO BE REATTACHED TO THE END OF THE CHUTE BY USING THE OLD TEK SCREWS

105 DUMPER EXTENSION CHUTE OPTION PAGE 44A NO PART NUMBER DESCRIPTION/NOTES QTY SERIAL # END CHUTE C148 BOLT-WHIZ 1/4 X 3/4 UNC GR C000 NUT-WHIZ 1/4 FLG UNC GR.5 4

106 500 - PAGE 45 REM DECALS REV. OCT 5/