IV. S-SERIES PRIVATE USE SPARE PARTS T

Transcription

1 -PRINT- APRIL TABLE OF CONTENTS- SPARE PARTS IV. S-SERIES PRIVATE USE SPARE PARTS T his chapter contains spare parts diagrams and lists for the RICON S-Series Private Use wheelchair lift. The exploded view of each major lift assembly shows individual components referenced by numbers. On each associated list are the reference numbers, part descriptions, quantities used, and Ricon part numbers. NOTE: To order a part, locate the part or assembly on an exploded view, note its reference number, find this number on the associated parts list (following page), and order the part number in the far right column. Most kits contain a single part (plus hardware). Therefore, you may need to order more than one kit if the part is used more than once on a major assembly. PARTS DIAGRAM... PAGE FIGURE 4-1: PRIVATE USE DECALS FIGURE 4-2: PRIVATE USE PUMP ASSEMBLY FIGURE 4-3: PRIVATE USE HYDRAULIC SYSTEM FIGURE 4-4: PRIVATE USE ELECTRICAL SYSTEM FIGURE 4-5: PRIVATE USE PENDANT FIGURE 4-6: PRIVATE USE PLATFORM FIGURE 4-7: PRIVATE USE TRAVELING FRAME FIGURE 4-8: PRIVATE USE HANDRAILS LIFT SPECIFICATIONS

2 S-SERIES LIFT This product is covered by one or more of the following patents: U.S. Patents Nos. x,xxx,xxx; x,xxx,xxx; x,xxx,xxx; x,xxx,xxx; x,xxx,xxx; x,xxx,xxx; Australian Patent No. xxxxxx; Canadian Patent No. xxxxxxx; Other U.S. and foreign patents pending. XX-XX-XXX Montague St., Pacoima, CA mfg. date: Made in U.S.A Nelson Road, Panorama City, CA mfg. date: Made in U.S.A SPARE PARTS APRIL 2015 MANUAL OPERATION 1 2 PART OF SERIAL NUMBER DECAL (LOCATED ON INNER SIDE OF HYDRAULIC CYLINDER (ONLY RICON REPLACEABLE) PART OF SERIAL NUMBER DECAL (ONLY RICON REPLACEABLE) CORPORATION CORPORATION C MANUAL OPERATION PN MAXIMUM LOAD PN MAX LOAD: 600 Lb (273 Kg) PUMP COVER PN S-SERIES PATENT NO. PN RICON LOGO PN WARNING S-SERIES PRIVATE USE WHEELCHAIR LIFTS RICON CORPORATION 7900 NELSON RD. PANORAMA CITY, CA (800) (818) OPERATING INSTRUCTIONS Deploy Lift: Enter Vehicle: Exit Vehicle: Stow Lift: MANUAL OPERATION DOT - Private Use Lift CAUTION OPERATING INSTRUCTIONS PN DOT-PRIVATE USE LIFT PN STAND CLEAR CAUTION PN FIGURE 4-1: PRIVATE USE DECAL LOCATIONS 4-2

3 APRIL 2015 SPARE PARTS This page intentionally left blank. 4-3

4 SPARE PARTS APRIL FIGURE 4-2: PRIVATE USE PUMP ASSY RSM

5 APRIL 2015 SPARE PARTS FIGURE 4-2: PRIVATE USE PUMP ASSY FIG. ITEM DESCRIPTION QTY CONFIG. PART NO. 1 KIT, SOLENOID, 12V, SPST BUS BAR, ISKRA MOTOR KIT, MOTOR ASSY, W/BRACKET, 12V KIT, PRESSURE SWITCH, WITH INSTRUCTIONS * LIGHT ASSY, INDICATOR, 12V (SUPERSEDED) SEE 5A A PCB, PUMP LED ASSY, 12V KIT, SPOOL VALVE, WITH DECELERATION, 12V A * KIT, SPOOL VALVE, WITH DECELERATION, 24V KIT, SEAL, PUMP, MANUAL BACK-UP 1 V2-SH BACK-UP PUMP, MANUAL 1 V2-SH FITTING ASSY, SNL, 1/4J X 1/4J, STEEL 1 VS-SH CABLE CLAMP, 3/16", NYLON (BAG OF 10) CIRCUIT BREAKER KIT, 8 AMP, W/HDWR & DECAL 1 V2-SH BRACKET, SOLENOID PIN & RETAINING RING 2 V2-SH MOTOR ASSY, 12V, 3", ISKRA DECAL, 8 AMP CIRCUIT BREAKER ADAPTER,.625 D-HOLE TO.484 ROUND 1 V2-ES SCREW, SHC, 1/4-20 X 2.25L (BAG OF 10) FITTING, SRT, 1/4J, STEEL 1 V2-SH LIGHT, LIFT ARMED INDICATOR, 12V, GREEN 1 UL-ES A * LIGHT, LIFT ARMED INDICATOR, 24V, GREEN 1 V2-ES WASHER, FLAT,.406X.812X.065 (BAG OF 10) TERM, SPL, M22-18 FULLINS, (BAG OF 10) COUNTER ASSY HYDRAULIC POPPET VALVE ASSY (DOWN VALVE), 12V 1 V2-SH A * HYDRAULIC POPPET VALVE ASSY (DOWN VALVE), 24V 1 V2-SH HOSE CLAMP 1 V2-SH RESERVOIR, PUMP, PLASTIC 1 V2-SH PLUG, RESERVOIR, BREATHER 1 V2-SH DECAL,OIL LEVEL WARNING RESERVOIR, PUMP, PLASTIC W/DECAL & PLUG CIRCUIT BREAKER, 30AMP, WHITE DECAL, 30 AMP BREAKER, HYDRAULIC, PUMP ASSY NOTE: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. NOTE: * Item or configuration not shown. 4-5

6 SPARE PARTS APRIL A B C D A D C B 24 E FIGURE 4-3: PRIVATE USE HYDRAULIC SYSTEM RSM

7 APRIL 2015 SPARE PARTS FIGURE 4-3: PRIVATE USE HYDRAULIC SYSTEM FIG. ITEM DESCRIPTION QTY CONFIG. PART NO. 1 HANDLE, MANUAL BACKUP PUMP 1 V2-SH KIT, TOOL CLIP, W/HARDWARE COVER, ASSY, PUMP, LH 1 V2-CV-220 3A * COVER, ASSY, PUMP, RH 1 V2-CV SCREW, HEX, 5/16-18 X 5/8 GR 5 (BAG OF 10) WASHER, FLT,.344 X.688 X.065 (BAG OF 10) HEX ROD, PUMP STANDOFF 2 V2-CV ** PUMP ASSY, w/interlock, 12V 1 PM A ** PUMP ASSY, w/interlock, 12V & DECELERATION 1 PM PLATE, PUMP COVER MOUNT 1 V2-AC-71 9 PLATE, PUMP MOUNT 1 V2-AC SCREW, FLAT HEAD, 5/16-18 X 3/4" (BAG OF 10) STUD, THREADED, 5/16-18 X 1.75" (BAG OF 10) CABLE TIE, 5.5, BLACK (BAG OF 10) TUBE, POLYURETHANE, 6MM x 4MM, BLACK 9' ADAPTOR, # 6 SAE MALE X # 4 JIC MALE FITTING, "L", MALE X 1/4, BARB 2 V2-SH KIT, CYL REPAIR (W/SEALS) (SUPERSEDED BY 21829) 2 V2-SH-56 16A* KIT, CYL REPAIR (PISTON/GLAND ASSY) KIT, FLOW CONTROL, FIXED RATE.50 GPM (KIT OF 2) SCREW, HEX RECESS HEAD, 1/4-20 X 1 (BAG OF 10) HOSE ASSY, HYDRAULIC, 61" X 1/4 JIC X 1/4 JIC 1 V2-SH HOSE ASSY, HYDRAULIC, 26" X 1/4 JIC X 1/4 JIC 1 V2-SH FITTING, RUN TEE, 1/4 JIC M-M-F 1 V2-SH FITTING, "L", 1/4 JIC M-F SWIVEL 3 VS-SH OIL, HYDRAULIC, TEXACO #15, MEETS MIL-H-5606G 1 GAL CYLINDER ASSY 37, (BLACK) 2 S1100 VT-SH-105K 2 S1200 VT-SH-105K 25 GROMMET, CATERPILLAR, 3/16 X SPACER, CABLE OR HOSE BUSHING, 3/4"ID X 3/8W * GLAND NUT, 1.50, WITH SEAL (SUPERSEDED BY 21829) A GLAND ASSY (FOR S/N ABOVE ) (SEE KIT 21829) NOTE: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. NOTE: * Item or configuration not shown. NOTE: ** Refer to Pump Assembly figure for parts breakdown. 4-7

8 SPARE PARTS APRIL A B A A 8 B 30 BRIDGEPLATE LOAD SENSOR MAIN CIRCUIT BREAKER FIGURE 4-4: PRIVATE USE ELECTRICAL SYSTEM RSM

9 APRIL 2015 SPARE PARTS FIGURE 4-4: PRIVATE USE ELECTRICAL SYSTEM FIG. ITEM DESCRIPTION QTY CONFIG. PART NO. 1 CAM, LIFT CONTROL 1 V2-AC SWITCH, LIMIT, FOLD CUTOFF 1 V2-ES BLOCK, FOLD CUTOFF SWITCH OFFSET, 1/4" THICK 1 V2-ES-78 4 BLOCK, FOLD CUTOFF SWITCH OFFSET, 3/8" THICK 1 V2-ES-79 5 SPRING, RETAINING, UPPER/LOWER SWITCH BLOCK 1 V2-ES-95 6 * SWITCH BLOCK ASSEMBLY (SUPERSEDED BY 34314) 2 V2-ES-82 6A SWITCH BLOCK ACTUATOR, FOLD CUTOFF 1 V2-AC SWITCH, LIMIT, FLOOR LEVEL POWER CUTOFF, UP & DOWN 2 V2-ES KIT, LIMIT SWITCH BLOCK REPLACEMENT 2 V2-ES SCREW, 4-40 X 1.25 PAN HEAD (BAG OF 10) SCREW, 4-40 X.75 PAN HEAD (BAG OF 10) NUT, HEX, 4-40 (BAG OF 10) ** ELECTRICAL HARNESS, MAIN, W/O INTERLOCK 1 S S MS, X ½ PHIL PAN (BAG OF 10) PIN, EXTENSION FOLD CUTOFF (BAG OF 10) MS X 1 3/4 PHIL PAN (BAG OF 10) MS 8-32 X 1 1/4 PHIL PAN (BAG OF 10) NUT, HEX, 8-32 NYLON INSERT (BAG OF 10) TAPE, NON-REFLECTIVE ENCLOSURE, SENSORS, SHORT SENSOR, PHOTOBEAM, RECEIVER SENSOR, PHOTOBEAM, TRANSMITTER SCREW, RD HEAD, X 2 (BAG OF 10) SPRING, COMPRESSION,.30 X 2.06L 2 V2-ES ROLLPIN,.94 X 1.0 (BAG OF 10) ROLLPIN,.94 X.50 (BAG OF 10) PCB ASSEMBLY, PRIVATE SHORTING PLUG 1 UL-ES * HARNESS, PCB TO CAM SWITCH KIT, CIRCUIT BREAKER, MAIN (90A) 12 VOLTS K 30A * KIT, CIRCUIT BREAKER, 50 AMP 24 VOLTS BRIDGEPLATE LOAD SENSOR NOTE: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. NOTE: * Item or configuration not shown. NOTE: ** Does not include all harnesses. Reference Item

10 SPARE PARTS APRIL FIGURE 4-5: PRIVATE USE PENDANT RSM

11 APRIL 2015 SPARE PARTS FIGURE 4-5: PRIVATE USE PENDANT FIG. ITEM DESCRIPTION QTY CONFIG. PART NO. 1 STOW/DEPLOY BUTTON, S-SERIES UP/DOWN BUTTON, S-SERIES V-BRACKET, PLASTIC, W/HARDWARE KIT, WALL MOUNT BRACKET, UNIVERSAL PENDANT KIT, CONTROL HARNESS STRAIN RELIEF, S-SERIES KIT, PENDANT, S-SERIES, 7 FT A* KIT, PENDANT, S-SERIES, COILED CORD B* KIT, PENDANT, S-SERIES, 10 FT C* KIT, PENDANT, S-SERIES, STEEL JACKETED CORD NOTE: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. NOTE: * Item or configuration not shown. 4-11

12 SPARE PARTS APRIL FIGURE 4-6A: PRIVATE USE SOLID PLATFORM RSM

13 APRIL 2015 SPARE PARTS FIGURE 4-6A: PRIVATE USE SOLID PLATFORM FIG. ITEM DESCRIPTION QTY CONFIG. PART NO. 1 * PLATFORM ASSY, SOLID, 30 X 38 1 S A * PLATFORM ASSY, SOLID, 30 X 44 1 S B * PLATFORM ASSY, SOLID, 30 X 51 1 S C PLATFORM ASSY, SOLID, 32 X 44 1 S D * PLATFORM ASSY, SOLID, 34 X 51 1 S E * PLATFORM ASSY, SOLID, 30 X 48 1 S F * PLATFORM ASSY, SOLID, 32 X 48 1 S ROLLSTOP ASSY, 6", 30" WIDE PLATFORM 1 S S A * ROLLSTOP ASSY, 6", 32" WIDE PLATFORM 1 S S S B * ROLLSTOP ASSY, 6", 32" WIDE PLATFORM 1 S S ROLLSTOP ASSY,INBOARD, 30" (BRIDGEPLATE) 1 S A * ROLLSTOP ASSY,INBOARD, 32" (BRIDGEPLATE) 1 S KIT, ROLLSTOP ACTUATOR REPLACEMENT, LH KIT, ROLLSTOP ACTUATOR REPLACEMENT, RH SPACER, BRIDGEPLATE SPRING 2 UV-PF BLOCK, PLATFORM LEVEL ADJUSTMENT 1 VT-AH KIT, COLLAR, ROLLSTOP ACTUATOR, SCREW, HEX HEAD, 1/4-20 X 7/8" (BAG OF 10) WASHER, 1/4 ID, FLAT SAE (BAG OF 10) NUT, HEX, 1/4-20, NYLON INSERT (BAG OF 10) "T" NUT, STAINLESS (BAG OF 10) BUSHING, BRONZE,.392ID 2 V2-BU BUMPER, UHMW PLASTIC, 75ID X.38 T 2 V2-AC NUT, HEX, 5/16-18 (BAG OF 10) SCREW, BUTTON HEAD, 5/16-18 X 3/4", SST (BAG OF 10) NUT, HEX, 5/16-18, NYLON INSERT, SST, (BAG OF 10) SCREW, TEK PAN HEAD, 8 X 3/4" (BAG OF 10) SCREW, HEX HEAD, 5/16-18 X 1, GR5 (BAG OF 10) SCREW, HEX HEAD, 1/4-20 X 1/2", GR5 (BAG OF 10) PIN, ROLLSTOP (BAG OF 10) WASHER, FLAT,.81OD X.41ID (BAG OF 10) SETSCREW, HEX RECESS, 1/2-20 X 1-1/4" (BAG OF 10) SETSCREW, HEX RECESS, 1/4-20 X 1/4 CUP POINT (BAG OF 10) NOTE: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. NOTE: * Fully assembled platform with all items shown except item 33 and 34. NOTE: ** Must be used with V2-AC

14 SPARE PARTS APRIL 2015 FIGURE 4-6A: PRIVATE USE SOLID PLATFORM (CONT D) FIG. ITEM DESCRIPTION QTY CONFIG. PART NO. 25 WASHER, FLAT, NYLON,.32ID X.75OD X.031 (BAG OF 10) SCREW, BUTTON HEAD, 1/4-20 X 3/8, SST (BAG OF 10) SCREW, BUTTON HEAD, 5/16-18 X 1/2, SST (BAG OF 10) ** CATCH, BASE LATCH 1 V2-AC RETAINING RING,.75" EXT (BAG OF 10) GUIDE, 1.00 OD X 1/4-20 ID BUSHING, 1"ID X 1/2" (BAG OF 10) SHIM, PVC 2 V2-BU KIT, SHAFT, MAIN, PLATFORM, 1" X 32.50", 26 (REF P/N VS-PI-14) A* KIT, SHAFT, MAIN, PLATFORM, 1" X 36.50", 30 (REF P/N VT-PI-43) B* KIT, SHAFT, MAIN, PLATFORM, 1" X 39.13", 32 (REF P/N VT-PI-49) BUSHING, STEEL,.25ID X.32OD X.19L 2 V2-BU SETSCREW, HEX RECESS 1/4-20 X 1/4", CONE POINT (BAG OF 10) SPRING, TORSION, RH 1 V2-SP SPRING, TORSION, LH 1 V2-SP KIT, HINGE, W/PIN, CHARCOAL GREY KIT, REPLACEMENT ASSY, 6 ROLLSTOP, 32 PLATFORM *** KIT, ROLL STOP GUARD NOTE: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. NOTE: * Fully assembled platform with all items shown except item 33 and 34. NOTE: ** Must be used with V2-AC-102. NOTE: *** Kit P/N must be used in any installation where a headrest is not present on applicable FMVSS compliant -G configured units. 4-14

15 APRIL 2015 SPARE PARTS This page intentionally left blank. 4-15

16 SPARE PARTS APRIL A 26 A FIGURE 4-6B: PRIVATE USE SPLIT PLATFORM RSM

17 APRIL 2015 SPARE PARTS FIGURE 4-6B: PRIVATE USE SPLIT PLATFORM FIG. ITEM DESCRIPTION QTY CONFIG. PART NO. 1 * PLATFORM ASSY, 26 X 28 SPLIT 1 S A * PLATFORM ASSY, 30 X 38 SPLIT 1 S B * PLATFORM ASSY, 30 X 42 SPLIT 1 S C * PLATFORM ASSY, 30 X 48 SPLIT 1 S ROLLSTOP ASSY, LH, SPLIT PLATFORM, 26 1 S A * ROLLSTOP ASSY, LH, SPLIT PLATFORM, 30 1 S S S ROLLSTOP ASSY, RH, SPLIT PLATFORM, 26 1 S A * ROLLSTOP ASSY, RH, SPLIT PLATFORM, 30 1 S S S BRIDGEPLATE, 26" ASSY 1 S A * BRIDGEPLATE, 30" ASSY 1 S S KIT, REPLACEMENT, ROLLSTOP ACTUATOR, LH, W/HDWR A * ROLLSTOP ACTUATOR ASSY, LH 1 S1132 V1-PF KIT, REPLACEMENT, ROLLSTOP ACTUATOR, RH, W/HDWR A * ROLLSTOP ACTUATOR ASSY, RH 1 S1132 V1-PF SPACER, BRIDGEPLATE SPRING 2 UV-PF BLOCK, PLATFORM LEVEL ADJUSTMENT 1 VT-AH BUMPER, RUBBER (BAG OF 10) SCREW, HEX HEAD, 1/4-20 X 7/8" (BAG OF 10) WASHER, 1/4 ID, FLAT SAE (BAG OF 10) NUT, HEX, 1/4-20, NYLON INSERT (BAG OF 10) "T" NUT, STAINLESS (BAG OF 10) BUSHING, BRONZE,.392ID 2 V2-BU BUMPER, UHMW PLASTIC, 75ID X.38 T 2 V2-AC NUT, HEX, 5/16-18 (BAG OF 10) SCREW, BUTTON HEAD, 5/16-18 X 1/2", SST (BAG OF 10) NUT, HEX, 5/16-18 (BAG OF 10) SCREW, TEK PAN HEAD, 8 X 3/4" (BAG OF 10) SCREW, HEX HEAD, 5/16-18 X 1, GR5 (BAG OF 10) SCREW, HEX, 1/4-20 X 1/2 GR5, SST (BAG OF 10) PIN, ROLLSTOP (BAG OF 10) BRACKET, ROD END ATTACHMENT 2 V3-PL WASHER, FLAT,.81OD X.41ID (BAG OF 10) SCREW, FLAT HEAD, 3/8-16 x 3/4" (BAG OF 10) NOTE: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. NOTE: * Fully assembled platform with all items shown except item 33 and 34. NOTE: ** Must be used with V2-AC

18 SPARE PARTS APRIL 2015 FIGURE 4-6B: PRIVATE USE SPLIT PLATFORM (CONT D) FIG. ITEM DESCRIPTION QTY CONFIG. PART NO. 26 SCREW, FLAT HEAD, 3/8-16 x 3/4" (BAG OF 10) SETSCREW, HEX RECESS, 1/4-20 X 1/4 CUP POINT (BAG OF 10) SAFETREAD, 2.75" X 14" 2 V2-AC RING, RETAINING,.25 OD (BAG OF 10) WASHER, FLAT, NYLON,.32ID X.75OD X.031 (BAG OF 10) SCREW, BUTTON HEAD, 1/4-20 X 3/8, SST (BAG OF 10) GUIDE, 1.00 OD X 1/4-20 ID 2 UL-AC SCREW, BUTTON HEAD, 5/16-18 X 1/2, SST (BAG OF 10) KIT, REPLACEMENT LATCH MECHANISM A* CATCH, BASE LATCH 1 V2-AC RETAINING RING,.75" EXT (BAG OF 10) BUSHING, FLANGED, 1" ID X 1/2W" (BAG OF 10) SAFETREAD, 9.75 X 5.50, BLACK ASSEMBLY, TIE ROD 2 VS-AH BALL JOINT, RH THREAD 2 VS-AH STUD, TIE ROD, LH THREAD TO RH THREAD 2 VS-AH BALL JOINT, LH THREAD, SST 2 VS-AH WASHER, SPLIT LOCK, 5/16" (BAG OF 10) NUT, HEX, 5/16-24 (BAG OF 10) KIT, SHAFT, MAIN, PLATFORM, 1" X 32.50", 26 (REF P/N VS-PI-14) A* KIT, SHAFT, MAIN, PLATFORM, 1" X 36.50", 30 (REF P/N VT-PI-43) B* KIT, SHAFT, MAIN, PLATFORM, 1" X 39.13", 32 (REF P/N VT-PI-49) SHIM, PVC 2 V2-BU PLUG, SQUARE, 1 1/8, BLACK PLASTIC BUSHING, STEEL,.25ID X.32OD X.19L 2 V2-BU COLLAR,.38ID 2 V2-BU SETSCREW, HEX RECESS 1/4-20 X 1/4", CONE POINT (BAG OF 10) SPRING, TORSION, RH 1 V3-SP SPRING, TORSION, LH 1 V3-SP PIN, HINGE, SPLIT PLATFORM (ONLY FOR 30 X 48 PLATFORM) 4 VS-PI-01 NOTE: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. NOTE: * Fully assembled platform with all items shown except item 33 and 34. NOTE: ** Must be used with V2-AC

19 APRIL 2015 SPARE PARTS This page intentionally left blank. 4-19

20 SPARE PARTS APRIL FIGURE 4-7: PRIVATE USE TRAVELING FRAME RSM

21 APRIL 2015 SPARE PARTS FIGURE 4-7: PRIVATE USE TRAVELING FRAME FIG. ITEM DESCRIPTION QTY CONFIG. PART NO. 1 BASEPLATE, 26 W/INTERLOCK 1 S A * BASEPLATE, 30 W/INTERLOCK 1 S B * BASEPLATE, 30 W/INTERLOCK 1 S * 1 S * 1 S * 1 S C * BASEPLATE, 32 W/INTERLOCK 1 S * 1 S * 1 S VERTICAL ARM ASSY, RH 1 S1100 V1-AC-241 2A * VERTICAL ARM ASSY, RH 1 S1200 VS-AC VERTICAL ARM ASSY, LH 1 S1100 V1-AC-242 3A * VERTICAL ARM ASSY, LH 1 S1200 VS-AC TOP ARM ASSY 2 S1100 VS-AC-250 4A * TOP ARM ASSY 2 S1200 VS-AC BOTTOM ARM ASSY 2 S1200 VS-AC SADDLE ASSEMBLY, W/T-NUT 2 VT-AC UPPER LINK, KNUCKLE 2 VT-AC LINK, KNUCKLE, LONG 2 S1100 V1-AC-069 8A * LINK, KNUCKLE, LONG 2 S1200 VS-AC RETAINING RING,.75" EXT (BAG OF 10) PIN, SNAP RING,.75 OD X 2.15L 2 VT-PI KIT, SPACER, IRS CAM SCREW, BUTTON HEAD, 1/4-20 X 1", SST (BAG OF 10) RETAINER, CAM ROLLER 4 V2-AC ROLLER, BRIDGEPLATE CAM 2 V2-AC PIN, CAM ROLLER 2 V2-PI FLANGE BEARING,.75ID (BAG OF 10) RIVET, BLIND, 3/16 X 3/8", ALUM (BAG OF 10) CAP, END, UPPER PARALLEL ARM 2 V2-AC SCREW, HEX HEAD, 1/4-20 x 3/4, GR5 (BAG OF 10) A SCREW, FLAT HEAD, 1/4-20 x ½ (BAG OF 10) WASHER, FLAT HEAD,.63OD x.28id x.065 (BAG OF 10) CABLE ASSY, REPLACEMENT, BRIDGEPLATE, 45.00" 2 S A * CABLE ASSY, REPLACEMENT, BRIDGEPLATE, 49.75" 2 S NUT, HEX, 1/4-20, NYLON INSERT (BAG OF 10) BEARING, GROOVED 8 VS-AH WASHER, FENDER, 1.00OD x.28id x.065 (BAG OF 10) BLOCK, PULLEY MOUNT, BRIDGEPLATE 2 V2-AC-112 NOTE: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. NOTE: * Item or configuration not shown. 4-21

22 SPARE PARTS APRIL 2015 FIGURE 4-7: PRIVATE USE TRAVELING FRAME (CONT D) FIG. ITEM DESCRIPTION QTY CONFIG. PART NO. 26 SCREW, BUTTON HEAD, 1/4-20 x 2 1/4, SST (BAG OF 10) T-NUT, FLAT HEAD, X.25 OD X.44L 2 V2-AC SCREW, FLAT HEAD, x ½ (BAG OF 10) CAM ASSY, BRIDGEPLATE ACTUATOR 2 V2-AC KIT, SPACER, RUBBER, BRIDGEPLATE CAM PIN, SNAP RING,.38 OD X 3.09 L 2 VS-PI RETAINING RING,.38 ID (BAG OF 10) BUSHING, STEEL,.25 ID X.32 OD X.19 L 2 V2-BU KIT, RETROFIT, PIN, LINK-ARM, w/ HDWR WASHER, FENDER, 5/16, SST (BAG OF 10) SCREW, BUTTON HEAD, 5/16-18 X 1/2 SST, w/ NYLCK (BAG OF 10) SETSCREW, 3/8-16 x 3/8, CUP PT (BAG OF 10) SPRING NUT, 10-24, U-TYPE (BAG OF 10) SCREW, PAN HEAD, x 1/2 (BAG OF 10) PLUG, 1" LOW PROFILE, BLACK NYLON BEARING, NYLINER, 3/8 ID 11/16 L BUMPER, BUTTON, BRIDGEPLATE CAM (BAG OF 10) BUMPER, BRIDGEPLATE CAM, ANTI-RATTLE 2 V2-BU SCREW, HEX HEAD, 1/4-20 X 1-3/4, GR5 (BAG OF 10) SPRING, UPPER PARALLEL ARM 2 V2-SP SETSCREW, 5/16-18 x 1, CUP PT (BAG OF 10) WASHER, KEYED KIT, LATCH RELEASE, 30", w/blocks & HDWR A KIT, LATCH RELEASE, 26", w/blocks & HDWR BLOCK, CENTER MOUNTING, BASE LATCH 1 V2-AC DOWEL PIN,.094 DIA X.38 L (BAG OF 10) BLOCK, MOUNT, BASE LATCH 1 V2-AC BRACKET, STOW LOCK SOLENOID 1 V2-AC KIT, SOLENOID ASSY, 12V 1 V2-ES CLIP, SPRING, BASE LATCH, SST 1 V2-AC SCREW, PAN HEAD, x ½ (BAG OF 10) A SCREW, FLAT HEAD, x ½, SST (BAG OF 10) NUT, HEX, NYLON INSERT, (BAG OF 10) PIN, SPRING MOUNTING 1 V2-PI SPRING, STO-LOCK RELEASE,.38OD X 3.5" 1 V2-SP SCREW, HEX HEAD, 5/16-18 X 3/4" (BAG OF 10) SCREW, FLAT HEAD, 5/16-18 X 3/4 (BAG OF 10) SCREW, BUTTON HEAD, 1/4-20 X 1/2", SST (BAG OF 10) COVER, BASE LATCH 1 V2-CV-123 NOTE: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. NOTE: * Item or configuration not shown. 4-22

23 APRIL 2015 SPARE PARTS FIGURE 4-7: PRIVATE USE TRAVELING FRAME (CONT D) FIG. ITEM DESCRIPTION QTY CONFIG. PART NO. 63 SCREW, HEX HEAD, 5/16-18 X.625, GR 5 (BAG OF 10) WASHER, FLAT,.69OD x.34id x.065 (BAG OF 10) SPRAY PAINT, TOUCH-UP, CHARCOAL BUSHING, E-COVER MOUNT 2 V2-BU SCREW, HEX HEAD, 1/4-20 X 1, GR5 (BAG OF 10) PIN, CONTROL CAM 1 V2-PI KIT, PINCH POINT SHIELD w/ HDWR, RH 1 S A * KIT, PINCH POINT SHIELD w/ HDWR, RH 1 S KIT, PINCH POINT SHIELD w/ HDWR, LH 1 S A * KIT, PINCH POINT SHIELD w/ HDWR, LH 1 S BUSHING, 5/8 OD X 3/16 ID 2 VS-AH GROMMET,.30 ID x.88 OD x.44 (BAG OF 10) KIT, REPLACEMENT SOLENOID, 12V GUIDE BLOCK, BRIDGEPLATE RIVET, BLIND, STEEL 3/16 X 5/8 (BAG OF 10) SPRING, KNUCKLE ACTUATOR 2 VT-SP-42 NOTE: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. NOTE: * Item or configuration not shown. 4-23

24 SPARE PARTS APRIL FIGURE 4-8: PRIVATE USE HANDRAILS RSM

25 APRIL 2015 SPARE PARTS FIGURE 4-8: PRIVATE USE HANDRAILS FIG. ITEM DESCRIPTION QTY CONFIG. PART NO. 1 HANDRAIL ASSEMBLY, RH 1 VS-AC HANDRAIL, RH 1 VS-AC RUBBER BUMPER, BAG OF CAP, BLACK HANDRAIL ASSEMBLY, LH, W/HARNESS 1 VS-AC HANDRAIL, LH 1 VS-AC HARNESS, ARM SWITCH 1 V2-ES-012 NOTE: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. NOTE: * Item or configuration not shown. 4-25

26 SPARE PARTS APRIL 2015 This page intentionally left blank. 4-26

27 APRIL 2015 SPARE PARTS APPENDIX 1 LIFT SPECIFICATIONS S-SERIES PERSONAL USE SOLID PLATFORM WHEELCHAIR LIFT Power... electro-hydraulic Motor 12 volts DC amp. avg/cycle, volts DC amp. avg/cycle, 1250 psi Hydraulic cylinders... 2 ea, 1.5", power-up/gravity-down Rated load capacity lbs Manual backup (up)... hand pump Manual backup (down)... pressure release valve Lift weight lbs MODEL DIMENSIONS (inches) A B C D E F G H Stationary frame width Height (folded) Installation depth (folded) Usable platform width Usable platform length Floor-toground travel Traveling frame width Clear entry width S S S S S S S

28 SPARE PARTS APRIL 2015 S-SERIES PRIVATE USE SPLIT PLATFORM LIFT Power...electro-hydraulic Motor 12 volts DC amp avg/cycle, volts DC amp avg/cycle, 1250 psi Hydraulic cylinders... 2 ea, 1.5", power-up/gravity-down Rated load capacity lbs Manual backup (up)... hand pump Manual backup (down)... pressure release valve Lift weight lbs MODEL DIMENSIONS (inches) A B C D E F G H Stationary frame width Height (folded) Installation depth (folded) Usable platform width Usable platform length Floor-toground travel Traveling frame width Clear entry width S S S S END OF TABLE -BACK TO TOP- 4-28