Stainless Steel Vertical Multistage Pump CONTENTS

Transcription

1 , EVMUG/L - V ertic ca l Multistage s D ata Book 6Hz

2 / EVMU(G)(L) CONTENTS SECTION PAGE FEATURES 2 TYPICAL APPLICATIONS 3 MODEL DESIGNATION 4 PRODUCT SPECIFICATIONS EVMU(G)(L)32 - EVMU(G)(L)64 6 CURVE SPECIFICATIONS 7 PERFORMANCE RANGE 8 SELECTION CHART 9 PERFORMANCE CURVES EVMU(G)(L)32 17 EVMU(G)(L)45 18 EVMU(G)(L)64 19 SHAFT SEAL 2 MECHANICAL SEAL 21 TECHNICAL DATA DIMENSIONS EVMU(G)(L)32 - EVMU(G)(L)64 3 MOTOR DIMENSION 28 SECTIONAL VIEW AND PARTS REFERENCE EVMU(G)(L)32 58 EVMU(G)(L)45 - EVMU(G)(L)64 6 Note: Models /L 1-2 and EVMU/EVMUL/EVMUG certified to NSF/ANSI 61 & 372. Certified to NSF/ANSI 61, ANNEX G All specifications subject to change without notice.

3 / EVMU(G)(L) FEATURES 1-2 Standard NEMA motor sizes Low axial thrust impeller enables long motor bearing life Air vent in casing cover allows proper venting preventing air entrapment and dry run Fill port in casing cover allows for water fill, as well as installation of sensors, gauges, and other measuring devices Liner ring is a self-aligning, floating design constructed to prevent swelling at high temperatures Tungsten carbide lower pump bearings and sleeves are standard construction for all services, providing maximum operating life Direct drive pump and motor shafts are keyed for positive, reliable power transmission with no adjustments necessary Flexible floating outer casing allows for thermal expansion in hot water applications, preventing deformation due to pressure fluctuations Square-edge four spline shaft provides positive location and drive of impellers, eliminating wear Dimensions & flanges installation is to market accepted dimensions for easy upgrade of existing installations Piping connection options include Fixed ANSI flange, Oval flange, Loose ANSI flange, victaulic, and clamp connections Mechanical seal Silicon Carbide/Carbon/Viton mechanical shaft seal. Cartridge mechanical seal design enables replacement without disassembling the motor bracket EVMU(G)(L) Standard NEMA motor sizes Integral thrust bearing to handle axial thrust loads Air vent in casing cover allows proper venting preventing air entrapment and dry run Liner ring is a self-aligning, floating design constructed to prevent swelling at high temperatures Tungsten carbide lower pump bearings and sleeves are standard construction for all services, providing maximum operating life Direct drive pump and motor shafts are keyed for positive, reliable power transmission with no adjustments necessary Flexible floating outer casing allows for thermal expansion in hot water applications, preventing deformation due to pressure fluctuations Anti-erosion measures a dish-shaped insert is fitted to the intermediate casing designed to promote smooth flow and prevent high velocity areas that accelerate erosion Square-edge twelve spline shaft (EVMU 32-64) provides positive location and drive of impellers eliminating wear Dimensions & flanges installation is to market accepted dimensions for easy upgrade of existing installations Mechanical seal Silicon Carbide/Carbon/Viton mechanical shaft seal. Cartridge mechanical seal design enables replacement without disassembling the motor bracket. 2

4 / EVMU(G)(L) TYPICAL APPLICATIONS Project: Model: ChkÊd: Date: INDU STRY BUILDING SERVICE WATER SUPPLY Water treatmentt reverse osmosis ultra-filtration water purification micro-filtration softening, ionizing and demineralising systems swimming pools separators Boiler feed steam systems condensate systems Wash and clean vehicle washing systems industrial part washing laundry systems supply of liquids with acids and bases supply of chemical liquids Chilling handling of refrigerants for cooling thermal control systems industrial cooling laser cooling Machine tool cooling lubricant supply for machine tools Pressure boosting pressure boosting for industrial use Food & beve age food washing systems bottle wash systems Pharmaceutical industries Marine applications freshwater, deckwash, high fog and fire fighting on ships Pressure boosting pressure e boosting for buildings pressure boosting for high rise buildings/hotels Sprinkler systems Fire fighting systems jockey pump District heating Heat exchangers / fan heaters Air conditioning systems Heating systems Water treatment water treatment plants filtration water treatment plants transfer Pressure boosting transfer from water treatment plants (mains) Irrigation golf course / sport fields irrigation Agriculture sprinkler irrigation drip irrigation 3

5 / EVMU(G)(L) MODEL DESIGNATION Project: Models 1, 3, 5, 1, 15, 2 Model: ChkÊd: Date: L 1, 3, 5, 1, 15, 2 Models EVMUG 32, 45, 64 EVMUL 32, 45, 64 4

6 PRODUCT SPECIFICATIONS (L) 1, 3, 5, 1, 15, 2Project: Model: ChkÊd: Date: Performance range Liquid Handling Size Key Component Materials Pipe connection Motor Nominal size Motor Power Capacity Total Head Type of liquid Maximum working pressure Liquid temperature range 1/2 to 25 HP 2.9 to US gpm 24.3 to 86 ft Clean water (for other clean liquids, consult factory) 23 / 375 psi (depending on model) -22 F to 248 F (-3 C to 12 C) Suction Discharge 1 1/4" 1 1/4" 2" 2" 1 1/4" 1 1/4" 2" 2" Impeller Intermediate casing Liner ring Bottom casing Casing cover + PPS + PPS Shaft AISI 316L (EN 1.444) AISI 329A (EN ) 1-3-5, (depending on model) L 1-3-5, L (depending on model) / L (depending on model) Shaft sleeve bearing Tungsten carbide Shaft Seal O-ring Outer casing Motor bracket Tie rod Coupling Base Version SiC/Carbon/ SiC+Graphite/SiC/ SiC/Carbon/EPDM SiC+Graphite/SiC/EPDM EPDM up to 5 HP from 7 1/2 HP Oval flange 23 psi Round flange (ANSI compatible raised face) 23 psi 375 psi Loose round flange 23 psi (ANSI compatible raised face) 375 psi victaulic 23 & 375 psi Clamp 23 & 375 psi Type Speed Power Requirements Direction of Rotation Motor Options PUMP L AISI 316L (EN 1.444) Cast Iron AISI 431 (EN 1.457) Die cast aluminium Cast Iron Die cast aluminium NEMA C/TC/TSC frame, TEFC or ODP enclosure 2- or 4- pole, 6 Hz, 35 or 175 rpm nominal speed 3 Phase, 23/46V or 28-23/46V - Single Phase, 115/23V Clockwise when viewed from motor end Consult factory for optional motor types Legend: Standard Options 5

7 EVMU(G)(L) PRODUCT SPECIFICATIONS EVMUG 32, 45, 64 EVMUL 32, 45, 64 Size Suction Discharge EVMUG ANSI raised face 2 1 /2'' for EVMUG32 3'' for EVMUG45 4'' for EVMUG64 ANSI raised face 2 1 /2'' for EVMUG32 3'' for EVMUG45 4'' for EVMUG64 EVMUL Range of HP 5 to 5HP Range of Performance at 345 RPM Capacity 66 to 39 GPM Head 44 to 93 feet Liquid handled Type of liquid Clean water (for other clean liquids, consult factory) Temperature 5 to +248 F (-15 to 12 C) Working pressure to 44 PSI (3 Bar) max. (see page 813 for specifics) Materials Impeller AISI 34 AISI 316 Intermediate casing AISI 34 AISI 316 Bottom casing Cast iron AISI 316 Casing cover Cast iron AISI 316 Outer casing AISI 34 AISI 316 Shaft AISI 316 AISI 316 Liner ring PTFE/AISI 316 Motor bracket Cast iron Cast iron/316 Base Cast iron Cast iron/316 Bearing Thrust Bearing : Sealed Ball Bearing Radial Bearing in wet end: Tungsten Carbide Shaft Seal Mechanical seal Silicon/Carbide/Carbon/ Motor Type Speed Three Phase Direction of Rotation Test standard NEMA TC/TSC frame 6 Hz, 345 RPM (2 poles) 28-23/46V Clockwise when viewed from motor end ISO 996 annex A Consult factory for optional motor types Note: Models /L 1-2 and EVMU/EVMUL/EVMUG certified to NSF/ANSI 61 &

8 CURVE SPECIFICATIONS The specifications below qualify the curves shown on the following pages. The curves refer to effective speed of 35 rpm for 2-pole asynchronous motors at 6 Hz. Measurements were carried out with clean water at 68 F of temperature and with a kinematic viscosity of v = 1 mm 2 /s (1 cst) The NPSH curve is an average curve obtained under the same conditions as the performance curves. The recommended operating range for best efficiency is indicated by the continuous portion of each curve. Symbols explanation: Q = volume flow rate H = total dynamic head (TDH) P2 = pump power input (shaft power) η= pump efficiency NPSH = net positive suction head required by the pump 7

9 / EVMU(G)(L) PERFORMANCE RANGE 8

10 SELECTION CHART (L) 1, 3, Maximum Q = Capacity Model Motor working US gpm pressure m³/h kw HP Frame Size (psi) H = Total Head in feet (L) C (L) C (L) C (L) C (L) C (L) C (L) C (L) C (375 opt.) (L) C (L) C (L) C (L) C (L) C (L) C (L) C (L) C (L) TC (L) TC (L) TC (L) TC (L) TC (L) C (L) C (L) C (L) C (L) C (L) C (L) C (L) C (375 opt.) (L) C (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) C (L) C (L) C (L) TC (L) TC (L) TC (375 opt.) (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC Model also available in 182TC/184TC frame 9

11 SELECTION CHART (L) Maximum Q = Capacity Model Motor working US gpm pressure m³/h kw HP Frame Size (psi) H = Total Head in feet (L) C (L) C (L) TC (L) TC (L) TC (L) TC (375 opt.) (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) C (L) TC (L) TC (L) TC (375 opt.) (L) TC (L) TC (L) TC (L) TC (L) TC (L) TC (L) TSC (L) TSC (L) TC (L) TC (L) TC (L) TC (375 opt.) (L) TC (L) TC (L) TC (L) TC (L) TSC (L) TSC Model also available in 182TC/184TC frame 1

12 PERFORMANCE CURVES 1 1/2HP - 3HP Nominal Speed: 35 RPM 3# ANSI 1 1 /4'' 4-Bolt Q [l/min] H [PSI] H [ft] 8 29/3 HP H [m] 24 27/3 HP /3 HP 24/3 HP /3 HP /2 HP 18/2 HP 16 16/2 HP /1.5 HP 12 13/1.5 HP /1.5 HP 11/1.5 HP 1/1 HP 9/1 HP 8 2 8/1 HP 7/.75 HP /.75 HP 5/.5 HP 4/.5 HP 3/.5 HP 4 2/.5 HP Q [US gpm].14 P2 [HP] % SINGLE IMPELLER HP 3 Q[m/h] 6 4 [%] NPSH [ft] Q [US gpm] 5 NPSH 3 [m] Q [US gpm] 11

13 PERFORMANCE CURVES 3 1/2HP - 5HP Nominal Speed: 35 RPM 3# ANSI 1 1 /4'' 4-Bolt Q [l/min] H [PSI] H [ft] 8 23/5 HP 22/5 HP H [m] /5 HP 2/5 HP 19/5 HP /5 HP /5 HP 15/3 HP 14/3 HP 16 13/3 HP /3 HP 11/3 HP 12 1/2 HP /2 HP 8/2 HP 7/1.5 HP 8 2 6/1.5 HP 5/1 HP /1 HP 3/.75 HP 4 2/.5 HP P2 [HP] Q [US gpm] Q[m/h].25 7 %.2 5 [%] SINGLE IMPELLER HP NPSH 1 [ft] Q [US gpm] 4 NPSH 2 [m] Q [US gpm] 12

14 PERFORMANCE CURVES 5 1HP - 1HP Nominal Speed: 35 RPM 3# ANSI 1 1 /4'' 4-Bolt Q [l/min] H [PSI] H [ft] /1 HP 17/7.5 HP 24 H [m] /7.5 HP 15/7.5 HP 14/7.5 HP /7.5 HP /7.5 HP 11/5 HP 16 1/5 HP /5 HP 8/5 HP /5 HP 6/3 HP 8 2 5/3 HP 4/2 HP /1.5 HP 2/1 HP 4 P2 [HP] Q [US gpm] % Q[m/h] 7 5 [%] NPSH [ft] SINGLE IMPELLER HP Q [US gpm] 8 NPSH 4 [m] Q [US gpm] 13

15 PERFORMANCE CURVES 1 1HP - 15HP Nominal Speed: 35 RPM 3# ANSI 2'' 8-Bolt Q [l/min] H [PSI] H [ft] /15 HP 15/15 HP 24 H [m] /15 HP 12/1 HP 11/1 HP /1 HP 9/7.5 HP /7.5 HP 7/7.5 HP /5 HP 5/5 HP 8 2 4/5 HP /3 HP 2/2 HP 4 1/1 HP P2 [HP] Q [US gpm] % SINGLE IMPELLER HP Q[m/h] 8 6 [%] 4 NPSH [ft] Q [US gpm] 8 NPSH 4 [m] Q [US gpm] 14

16 PERFORMANCE CURVES 15 2HP - 25HP Nominal Speed: 35 RPM 3# ANSI 2'' 8-Bolt Q [l/min] H [PSI] H [ft] /25 HP 11/25 HP 24 H [m] /2 HP 9/2 HP /2 HP 7/15 HP /15 HP 12 5/1 HP /1 HP 8 2 3/7.5 HP /5 HP 4 1/2 HP Q [US gpm] P2 % [HP] 2 3 Q[m/h] 8 6 [%] NPSH 2 [ft] 1 SINGLE IMPELLER HP Q [US gpm] 8 NPSH 4 [m] Q [US gpm] 15

17 PERFORMANCE CURVES 2 3HP - 25HP Nominal Speed: 35 RPM 3# ANSI 2'' 8-Bolt Q [l/min] H [PSI] H [ft] /25 HP 24 H [m] /25 HP 8/2 HP /2 HP 6/15 HP /15 HP /1 HP 3/7.5 HP /5 HP 1/3 HP Q [US gpm] P2 % [HP] Q[m/h] 8 6 [%] NPSH 3 [ft] 2 1 SINGLE IMPELLER HP Q [US gpm] 12 8 NPSH [m] 4 Q [US gpm] 16

18 EVMU(G)(L) PERFORMANCE CURVES EVMU32 5HP - 4HP EVMU32 1 EVMU Nominal Speed: 345 RPM 15# ANSI 2 1 /2'' 4-Bolt EVMU32 5 EVMU Nominal Speed: 345 RPM 3# ANSI 2 1 /2'' 8-Bolt 335 H (m) H (ft) 1 EVMU HP EVMU32 9 4HP EVMU HP EVMU32 7 3HP EVMU HP EVMU32 5 2HP EVMU HP EVMU HP EVMU HP EVMU HP EVMU32 1 5HP NPSH US GPM 5 NPSH (ft) 1.5 NPSH (m) eff. % Q m 3 /h US GPM Water Temperature: 2 C (68 F) 17

19 EVMU(G)(L) PERFORMANCE CURVES EVMU45 7.5HP - 5HP EVMU EVMU45 3 Nominal Speed: 345 RPM 15# ANSI 3'' 4-Bolt EVMU EVMU Nominal Speed: 345 RPM 3# ANSI 3'' 8-Bolt 274 H (m) H (ft) 8 EVMU HP EVMU45 6 5HP EVMU45 5 4HP EVMU HP EVMU HP EVMU HP EVMU HP EVMU45 1 1HP EVMU HP NPSH 1 5 NPSH (ft) NPSH (m) US GPM eff. % Q m 3 /h US GPM Water Temperature: 2 C (68 F) 18

20 EVMU(G)(L) PERFORMANCE CURVE EVMU EVMU64 3 EVMU64 1HP - 5HP 15# ANSI 4'' 8-Bolt EVMU EVMU64 4 Nominal Speed: 345 RPM EVMU EVMU EVMU EVMU # ANSI 4 8-Bolt 183 H (m) 6 H (ft) EVMU64 4 5HP EVMU HP EVMU64 3 4HP EVMU HP 91 3 EVMU HP EVMU HP EVMU HP EVMU HP NPSH 1 5 NPSH (ft) NPSH (m) US GPM eff. % Q m 3 /h US GPM Water Temperature: 2 C (68 F) 19

21 SHAFT SEAL (L) 1, 3, 5, 1, 15, 2 up to 23 PSI Cartridge Unbalanced type from 23 to 375 PSI Cartridge Balanced type model Shaft seal type Shaft seal material Max operating pressure 23 PSI 375 PSI Operating temperature range Liquid temperature range - 22 F to F* - 22 F to F* - 22 F to F * - 22 F to F * Cartridge Unbalanced Balanced Rotating Part SiC SiC SiC with graphite SiC with graphite Stationary Part Carbon Carbon SiC SiC Elastomers EPDM EPDM Compression spring - 22 F to F * SiC Carbon EPDM AISI 316 E - 22 F to F * SiC Carbon AISI 316 S AISI 316 AISI 316 AISI 316 AISI 316 Collar Type key E S R G *Operation above 248 F is possible under certain conditions. Consult factory for details. NOTE: Refer to selection tables on pages 9 and 1 for working pressure by model. Legend: Standard Options model Shaft seal type Max operating pressure d1 d2 d3 d4 l [in] [in] [in] [in] [in] (L) 1/3/5 (L) 1/15/2 Cartridge Cartridge Unbalanced 23 PSI Balanced 375 PSI Unbalanced 23 PSI Balanced 375 PSI Dimensions conform to standard EN

22 EVMU(G)(L) MECHANICAL SEAL EVMUG 32, 45, 64 EVMUL 32, 45, 64 working pressure to 37 PSI Standard Seal working pressure to 44 PSI Standard Seal Size (inch) Max. working pressure (psi) 232 d (inch) d1 (inch) d2 (inch) d3 (inch) d4 (inch) L1 (inch) L2 (inch) L3 (inch) L4 (inch) L5 (inch) A stationary seal ring Material B rotary seal ring elastomer spring Carbon Silicon graphite Carbide 316 Ti Maximum Working Pressure Model Maximum Working Pressure EVMU32 1 EVMU EVMU EVMU PSI EVMU EVMU64 3 EVMU32 5 EVMU EVMU EVMU PSI EVMU EVMU64 4 EVMU32 9 EVMU PSI 21

23 TECHNICAL DATA (L)1 DIMENSIONS Motor dimensions are located on pages 28 and 29 (L)1 Motor Frame Round flange (F) Loose round flange (LF) Oval flange (N) victaulic connection (V) Clamp connection (C) Model Pmax [psi] HP TEFC ODP TEFC ODP TEFC ODP TEFC ODP NEMA Frame A HP NEMA Frame A (L) C 6 5/8".5 56C 6 5/8" 11 7/8" 25.1 lb 11 7/8" 25.1 lb 1 7/8" 23.6 lb 1 7/8" 23.6 lb 1 7/8" 23.6 lb 1 7/8" 23.6 lb (L) C 6 5/8".5 56C 6 5/8" 12 11/16" 26.2 lb 12 11/16" 26.2 lb 11 11/16" 24.7 lb 11 11/16" 24.7 lb 11 3/4" 24.4 lb 11 3/4" 24.4 lb (L) C 6 5/8".5 56C 6 5/8" 13 9/16" 27.1 lb 13 9/16" 27.1 lb 12 9/16" 25.5 lb 12 9/16" 25.5 lb 12 9/16" 25.3 lb 12 9/16" 25.3 lb (L) C 6 5/8".5 56C 6 5/8" 14 3/8" 28. lb 14 3/8" 28. lb 13 3/8" 26.7 lb 13 3/8" 26.7 lb 13 3/8" 26.4 lb 13 3/8" 26.4 lb (L) C 6 5/8".75 56C 6 5/8" 15 3/16" 28.9 lb 15 3/16" 28.9 lb 14 3/16" 27.5 lb 14 3/16" 27.5 lb 14 3/16" 27.3 lb 14 3/16" 27.3 lb (L) C 6 5/8".75 56C 6 5/8" 16" 3.4 lb 16" 3.4 lb 15" 29.1 lb 15" 29 1/13" 15" 28.9 lb 15" 28.9 lb (L) C 6 5/8" 1 56C 6 5/8" 16 13/16" 31.2 lb 16 13/16" 31.2 lb 15 13/16" 29.6 lb 15 13/16" 29.6 lb 15 7/8" 29.4 lb 15 7/8" 29.4 lb (L) C 6 5/8" 1 56C 6 5/8" 17 11/16" 32. lb 17 11/16" 32. lb 16 11/16" 3.5 lb 16 11/16" 3.5 lb 16 11/16" 3.5 lb 16 11/16" 3.5 lb (L) C 6 5/8" 1 56C 6 5/8" 18 1/2" 32.9 lb 18 1/2" 32.9 lb 17 1/2" 31.6 lb 17 1/2" 31.6 lb 17 1/2" 31.4 lb 17 1/2" 31.4 lb (L) C 6 5/8" C 6 5/8" 19 5/16" 34. lb 19 5/16" 34. lb 18 5/16" 32.5 lb 18 5/16" 32.5 lb 18 5/16" 32.3 lb 18 5/16" 32.3 lb (L) C 6 5/8" C 6 5/8" 2 1/8" 34.9 lb 2 1/8" 34.9 lb 19 1/8" 33.4 lb 19 1/8" 33.4 lb 19 3/16" 33.4 lb 19 3/16" 33.4 lb (L) C 6 5/8" C 6 5/8" 21" 36.4 lb 21" 36.4 lb 2" 34.9 lb 2" 34.9 lb 2" 34.9 lb 2" 34.9 lb (L) C 6 5/8" C 6 5/8" 21 13/16" 37.3 lb 21 13/16" 37.3 lb 2 13/16" 35.8 lb 2 13/16" 35.8 lb 2 13/16" 35.8 lb 2 13/16" 35.8 lb (L) C 6 5/8" 2 56C 6 5/8" 23 7/16" 39.2 lb 23 7/16" 39.2 lb 22 7/16" 37.7 lb 22 7/16" 37.7 lb 22 7/16" 37.7 lb 22 7/16" 37.7 lb (L) C 6 5/8" 2 56C 6 5/8" 25 1/8" 41.2 lb 25 1/8" 41.2 lb 24 1/8" 39.7 lb 24 1/8" 39.7 lb 24 1/8" 39.7 lb 24 1/8" 39.7 lb (L) C 6 5/8" 2 56C 6 5/8" 26 3/4" 43.2 lb 26 3/4" 43.2 lb /4" 41.7 lb 25 3/4" 41.7 lb (L) TC 6 5/8" 3 145TC 6 5/8" 28 7/16" 46.3 lb 28 7/16" 46.3 lb /16" 44.7 lb 27 7/16" 44.7 lb (L) TC 6 5/8" 3 145TC 6 5/8" 3 1/16" 48.5 lb 3 1/16" 48.5 lb /16" 46.9 lb 29 1/16" 46.9 lb (L) TC 6 5/8" 3 145TC 6 5/8" 31 3/4" 5.5 lb 31 3/4" 5.5 lb /4" 48.9 lb 3 3/4" 48.9 lb (L) TC 6 5/8" 3 145TC 6 5/8" 32 9/16" 51.6 lb 32 9/16" 51.6 lb /16" 5. lb 31 9/16" 5. lb (L) TC 6 5/8" 3 145TC 6 5/8" 34 3/16" 53.6 lb 34 3/16" 53.6 lb /16" 52. lb 33 3/16" 52. lb Model also available in 182TC/184TC frame 22

24 TECHNICAL DATA (L)3 DIMENSIONS Motor dimensions are located on pages 28 and 29 (L)3 Motor Frame Round flange (F) Loose round flange (LF) Oval flange (N) victaulic connection (V) Clamp connection (C) Model Pmax [psi] HP TEFC ODP TEFC ODP TEFC ODP TEFC ODP NEMA Frame A HP NEMA Frame A (L) C 6 5/8".5 56C 6 5/8" 11 7/8" 24.9 lb 11 7/8" 24.9 lb 1 7/8" 23.3 lb 1 7/8" 23.3 lb 1 7/8" 23.1 lb 1 7/8" 23.1 lb (L) C 6 5/8".75 56C 6 5/8" 12 11/16" 25.8 lb 12 11/16" 25.8 lb 11 11/16" 24.2 lb 11 11/16" 24.2 lb 11 11/16" 24.2 lb 11 11/16" 24.2 lb (L) C 6 5/8" 1 56C 6 5/8" 13 9/16" 26.7 lb 13 9/16" 26.7 lb 12 9/16" 25.4 lb 12 9/16" 25.4 lb 12 9/16" 25.2 lb 12 9/16" 25.2 lb (L) C 6 5/8" 1 56C 6 5/8" 14 3/8" 27.8 lb 14 3/8" 27.8 lb 13 3/8" 26.3 lb 13 3/8" 26.3 lb 13 3/8" 26.1 lb 13 3/8" 26.1 lb (L) C 6 5/8" C 6 5/8" 15 3/16" 28.7 lb 15 3/16" 28.7 lb 14 3/16" 27.2 lb 14 3/16" 27.2 lb 14 3/16" 27. lb 14 3/16" 27. lb (L) C 6 5/8" C 6 5/8" 16" 29.6 lb 16" 29.6 lb 15" 28.1 lb 15" 28.1 lb 15" 28.1 lb 15" 28.1 lb (L) C 6 5/8" 2 56C 6 5/8" 16 13/16" 3.2 lb 16 13/16" 3.2 lb 15 13/16" 28.9 lb 15 13/16" 28.9 lb 15 13/16" 28.6 lb 15 13/16" 28.6 lb (L) C 6 5/8" 2 56C 6 5/8" 17 11/16" 31.1 lb 17 11/16" 31.1 lb 16 11/16" 29.7 lb 16 11/16" 29.7 lb 16 11/16" 29.5 lb 16 11/16" 29.5 lb (L) C 6 5/8" 2 56C 6 5/8" 18 1/2" 32.2 lb 18 1/2" 32.2 lb 17 1/2" 3.6 lb 17 1/2" 3.6 lb 17 1/2" 3.4 lb 17 1/2" 3.4 lb (L) TC 6 5/8" 3 145TC 6 5/8" 19 5/16" 33.1 lb 19 5/16" 33.1 lb 18 5/16" 31.5 lb 18 5/16" 31.5 lb 18 5/16" 31.3 lb 18 5/16" 31.3 lb (L) TC 6 5/8" 3 145TC 6 5/8" 2 1/8" 33.7 lb 2 1/8" 33.7 lb 19 1/8" 32.4 lb 19 1/8" 32.4 lb 19 1/8" 32.2 lb 19 1/8" 32.2 lb (L) TC 6 5/8" 3 145TC 6 5/8" 21" 35.5 lb 21" 35.5 lb 2" 33.9 lb 2" 33.9 lb 2" 33.9 lb 2" 33.9 lb (L) TC 6 5/8" 3 145TC 6 5/8" 21 13/16" 36.4 lb 21 13/16" 36.4 lb 2 13/16" 34.8 lb 2 13/16" 34.8 lb 2 13/16" 34.8 lb 2 13/16" 34.8 lb (L) TC 9 1/16" Consult Factory 26 1/8" 42.5 lb Consult Factory 25 1/8" 41.2 lb Consult Factory 25 1/8" 4.9 lb Consult Factory (L) TC 9 1/16" 5 184TC 9 1/16" 26 15/16" 44.7 lb 26 15/16" 44.7 lb /16" 43.1 lb 25 15/16" 43.1 lb (L) TC 9 1/16" 5 184TC 9 1/16" 27 13/16" 45.8 lb 27 13/16" 45.8 lb /16" 44. lb 26 13/16" 44. lb (L) TC 9 1/16" 5 184TC 9 1/16" 29 7/16" 47.8 lb 29 7/16" 47.8 lb /16" 46. lb 28 7/16" 46. lb (L) TC 9 1/16" 5 184TC 9 1/16" 3 1/4" 48.7 lb 3 1/4" 48.7 lb /4" 47.1 lb 29 1/4" 47.1 lb (L) TC 9 1/16" 5 184TC 9 1/16" 31 1/16" 49.8 lb 31 1/16" 49.8 lb /16" 48. lb 3 1/16" 48. lb (L) TC 9 1/16" 5 184TC 9 1/16" 31 15/16" 5.6 lb 31 15/16" 5.6 lb /16" 49.1 lb 3 15/16" 49.1 lb (L) TC 9 1/16" 5 184TC 9 1/16" 32 3/4" 51.7 lb 32 3/4" 51.7 lb /4" 5. lb 31 3/4" 5. lb Model also available in 182TC/184TC frame 23

25 TECHNICAL DATA (L)5 DIMENSIONS Motor dimensions are located on pages 28 and 29 (L)5 Motor Frame Round flange (F) Loose round flange (LF) Oval flange (N) victaulic connection (V) Clamp connection (C) Model Pmax [psi] HP TEFC NEMA Frame A HP ODP TEFC ODP TEFC ODP TEFC ODP NEMA Frame A (L) C 6 5/8" 1 56C 6 5/8" 12 7/16" 25. lb 12 7/16" 25. lb 11 7/16" 22.8 lb 11 7/16" 22.8 lb 11 7/16" 22.6 lb 11 7/16" 22.6 lb (L) C 6 5/8" C 6 5/8" 13 9/16" 26.1 lb 13 9/16" 26.1 lb 12 9/16" 23.7 lb 12 9/16" 23.7 lb 12 9/16" 23.7 lb 12 9/16" 23.7 lb (L) C 6 5/8" 2 56C 6 5/8" 14 5/8" 27.3 lb 14 5/8" 27.3 lb 13 5/8" 25.1 lb 13 5/8" 25.1 lb 13 5/8" 24.9 lb 13 5/8" 24.9 lb (L) TC 6 5/8" 3 145TC 6 5/8" 15 3/4" 28.4 lb 15 3/4" 28.4 lb 14 3/4" 26. lb 14 3/4" 26. lb 14 3/4" 26. lb 14 3/4" 26. lb (L) TC 6 5/8" 3 145TC 6 5/8" 16 13/16" 29.3 lb 16 13/16" 29.3 lb 15 13/16" 27.1 lb 15 13/16" 27.1 lb 15 13/16" 26.9 lb 15 13/16" 26.9 lb (L) TC 9 1/16" 5 184TC 9 1/16" 21 7/16" 36.1 lb 21 7/16" 36.1 lb 2 7/16" 33.9 lb 2 7/16" 33.9 lb 2 7/16" 33.7 lb 2 7/16" 33.7 lb (L) TC 9 1/16" 5 184TC 9 1/16" 22 9/16" 36.8 lb 22 9/16" 36.8 lb 21 9/16" 34.6 lb 21 9/16" 34.6 lb 21 9/16" 34.3 lb 21 9/16" 34.3 lb (L) TC 9 1/16" 5 184TC 9 1/16" 23 5/8" 37.9 lb 23 5/8" 37.9 lb 22 5/8" 35.4 lb 22 5/8" 35.4 lb 22 5/8" 35.4 lb 22 5/8" 35.4 lb (L) TC 9 1/16" 5 184TC 9 1/16" 24 3/4" 39. lb 24 3/4" 39. lb 23 3/4" 36.5 lb 23 3/4" 36.5 lb 23 3/4" 36.5 lb 23 3/4" 36.5 lb (L) TC 9 1/16" 5 184TC 9 1/16" 25 7/8" 4.5 lb 25 7/8" 4.5 lb 24 7/8" 38.3 lb 24 7/8" 38.3 lb 24 7/8" 38.1 lb 24 7/8" 38.1 lb (L) TC 9 1/16" 27 9/16" 51.8 lb /16" 49.4 lb (L) TC 9 1/16" 28 11/16" 56.1 lb /16" 53.6 lb (L) TC 9 1/16" 29 13/16" 57.2 lb /16" 54.7 lb (L) TC 9 1/16" Consult Factory 3 7/8" 58.3 lb Consult Factory /8" 55.8 lb Consult Factory (L) TC 9 1/16" 32" 59.6 lb " 57.2 lb (L) TC 9 1/16" 33 1/8" 6.9 lb /8" 58.5 lb (L) TC 9 1/16" 35 5/16" 62.9 lb /16" 6.5 lb Model also available in 182TC/184TC frame 24

26 TECHNICAL DATA (L)1 DIMENSIONS Motor dimensions are located on pages 28 and 29 (L)1 Motor Frame Round flange (F) Loose round flange (LF) Oval flange (N) victaulic connection (V) Clamp connection (C) Model Pmax [psi] HP TEFC ODP TEFC ODP TEFC ODP TEFC ODP NEMA Frame A HP NEMA Frame A (L) C 6 5/8" 1 56C 6 5/8" 14 3/8" 45.5 lb 14 3/8" 45.5 lb 14 3/8" 43.3 lb 14 3/8" 43.3 lb 14 3/8" 43.1 lb 14 3/8" 43.1 lb (L) C 6 5/8" 2 56C 6 5/8" 14 3/8" 46.3 lb 14 3/8" 46.3 lb 14 3/8" 43.9 lb 14 3/8" 43.9 lb 14 3/8" 43.9 lb 14 3/8" 43.9 lb (L) TC 6 5/8" 3 145TC 6 5/8" 15 5/8" 48.1 lb 15 5/8" 48.1 lb 15 9/16" 45.9 lb 15 9/16" 45.9 lb 15 9/16" 45.9 lb 15 9/16" 45.9 lb (L) TC 9 1/16" 5 184TC 9 1/16" 21 1/16" 59.4 lb 21 1/16" 59.4 lb 21 1/16" 57.2 lb 21 1/16" 57.2 lb 21 1/16" 57. lb 21 1/16" 57. lb (L) TC 9 1/16" 5 184TC 9 1/16" 22 1/4" 61.2 lb 22 1/4" 61.2 lb 22 1/4" 59. lb 22 1/4" 59. lb 22 1/4" 59. lb 22 1/4" 59. lb (L) TC 9 1/16" 5 184TC 9 1/16" 23 7/16" 63.2 lb 23 7/16" 63.2 lb 23 7/16" 6.7 lb 23 7/16" 6.7 lb 23 7/16" 6.7 lb 23 7/16" 6.7 lb (L) TC 9 1/16" TC 9 1/16" 24 5/8" 68. lb 24 5/8" 68. lb 24 5/8" 65.6 lb 24 5/8" 65.6 lb 24 5/8" 65.6 lb 24 5/8" 65.6 lb (L) TC 9 1/16" TC 9 1/16" 25 13/16" 7.7 lb 25 13/16" 7.7 lb 25 13/16" 68.3 lb 25 13/16" 68.3 lb 25 13/16" 68.3 lb 25 13/16" 68.3 lb (L) TC 9 1/16" TC 9 1/16" 27" 72.4 lb 27" 72.4 lb 27" 7.2 lb 27" 7.2 lb 27" 7. lb 27" 7. lb (L) TC 9 1/16" 1 215TC 9 1/16" 28 3/16" 75.2 lb 28 3/16" 75.2 lb 28 3/16" 73. lb 28 3/16" 73. lb 28 3/16" 73. lb 28 3/16" 73. lb (L) TC 9 1/16" 1 215TC 9 1/16" 29 3/8" 78.9 lb 29 3/8" 78.9 lb /8" 76.5 lb 29 3/8" 76.5 lb (L) TC 9 1/16" 1 215TC 9 1/16" 3 9/16" 8.9 lb 3 9/16" 8.9 lb /16" 78.5 lb 3 9/16" 78.5 lb (L) TC 9 1/16" TC 9 1/16" 32 7/8" 9.8 lb 32 7/8" 9.8 lb /8" 88.4 lb 32 7/8" 88.4 lb (L) TC 9 1/16" TC 9 1/16" 34 1/16" 92.8 lb 34 1/16" 92.8 lb /16" 9.6 lb 34 1/16" 9.6 lb (L) TC 9 1/16" TC 9 1/16" 35 1/4" 94.8 lb 35 1/4" 94.8 lb /4" 92.6 lb 35 1/4" 92.6 lb Model also available in 182TC/184TC frame 25

27 TECHNICAL DATA (L)15 DIMENSIONS Motor dimensions are located on pages 28 and 29 (L)15 Motor Frame Round flange (F) Loose round flange (LF) Oval flange (N) victaulic connection (V) Clamp connection (C) Model Pmax [psi] HP TEFC ODP TEFC ODP TEFC ODP TEFC ODP NEMA Frame A HP NEMA Frame A (L) C 6 5/8" 2 56C 6 5/8" 15 5/16" 41.7 lb 15 5/16" 41.7 lb 15 5/16" 37.5 lb 15 5/16" 37.5 lb 15 5/16" 37.5 lb 15 5/16" 37.5 lb (L) TC 9 1/16" 5 184TC 9 1/16" 19 11/16" 51.5 lb 19 11/16" 51.5 lb 19 11/16" 47.5 lb 19 11/16" 47.5 lb 19 11/16" 47.3 lb 19 11/16" 47.3 lb (L) TC 9 1/16" TC 9 1/16" 21 1/4" 57.2 lb 21 1/4" 57.2 lb 21 1/4" 53. lb 21 1/4" 53. lb 21 1/4" 53. lb 21 1/4" 53. lb (L) TC 9 1/16" 1 215TC 9 1/16" 22 13/16" 6.8 lb 22 13/16" 6.8 lb 22 13/16" 56.6 lb 22 13/16" 56.6 lb 22 13/16" 56.6 lb 22 13/16" 56.6 lb (L) TC 9 1/16" 1 215TC 9 1/16" 24 3/8" 63.3 lb 24 3/8" 63.3 lb 24 3/8" 59.1 lb 24 3/8" 59.1 lb 24 3/8" 59.1 lb 24 3/8" 59.1 lb (L) TC 9 1/16" TC 9 1/16" 25 15/16" 72.8 lb 25 15/16" 72.8 lb 25 15/16" 68.8 lb 25 15/16" 68.8 lb 25 15/16" 68.6 lb 25 15/16" 68.6 lb (L) TC 9 1/16" TC 9 1/16" 27 1/2" 77. lb 27 1/2" 77. lb 27 1/2" 72.8 lb 27 1/2" 72.8 lb 27 1/2" 72.8 lb 27 1/2" 72.8 lb (L) TC 9 1/16" 2 256TC 9 1/16" 29 11/16" 86.9 lb 29 11/16" 86.9 lb /16" 82.7 lb 29 11/16" 82.7 lb (L) TC 9 1/16" 2 256TC 9 1/16" 31 1/4" 89.7 lb 31 1/4" 89.7 lb /4" 85.5 lb 31 1/4" 85.5 lb (L) TC 9 1/16" 2 256TC 9 1/16" 32 13/16" 92.6 lb 32 13/16" 92.6 lb /16" 88.4 lb 32 13/16" 88.4 lb (L) TSC 11" Consult Factory 33 11/16" 91.8 lb Consult Factory /16" 87.7 lb Consult Factory (L) TSC 11" 35 5/16" 94.7 lb /16" 9.5 lb 26

28 TECHNICAL DATA (L)2 DIMENSIONS Motor dimensions are located on pages 28 and 29 (L)2 Motor Frame Round flange (F) Loose round flange (LF) Oval flange (N) victaulic connection (V) Clamp connection (C) Model Pmax [psi] HP TEFC ODP TEFC ODP TEFC ODP TEFC ODP NEMA Frame A HP NEMA Frame A (L) TC 6 5/8" 3 145TC 6 5/8" 15 3/8" 41.5 lb 15 3/8" 41.5 lb 15 3/8" 37.5 lb 15 3/8" 37.5 lb 15 3/8" 37.3 lb 15 3/8" 37.3 lb (L) TC 9 1/16" 5 184TC 9 1/16" 19 11/16" 51.5 lb 19 11/16" 51.5 lb 19 11/16" 47.5 lb 19 11/16" 47.5 lb 19 11/16" 47.3 lb 19 11/16" 47.3 lb (L) TC 9 1/16" TC 9 1/16" 21 1/4" 57.2 lb 21 1/4" 57.2 lb 21 1/4" 53. lb 21 1/4" 53. lb 21 1/4" 53. lb 21 1/4" 53. lb (L) TC 9 1/16" 1 215TC 9 1/16" 22 13/16" 6.8 lb 22 13/16" 6.8 lb 22 13/16" 56.9 lb 22 13/16" 56.9 lb 22 13/16" 56.6 lb 22 13/16" 56.6 lb (L) TC 9 1/16" TC 9 1/16" 24 3/8" 69.5 lb 24 3/8" 69.5 lb 24 3/8" 65.5 lb 24 3/8" 65.5 lb 24 3/8" 65.3 lb 24 3/8" 65.3 lb (L) TC 9 1/16" TC 9 1/16" 25 15/16" 7.1 lb 25 15/16" 7.1 lb 25 15/16" 65.9 lb 25 15/16" 65.9 lb 25 15/16" 65.9 lb 25 15/16" 65.9 lb (L) TC 9 1/16" 2 256TC 9 1/16" 28 1/8" 83.5 lb 28 1/8" 83.5 lb /8" 79.4 lb 28 1/8" 79.4 lb (L) TC 9 1/16" 2 256TC 9 1/16" 29 11/16" 86.4 lb 29 11/16" 86.4 lb /16" 82.2 lb 29 11/16" 82.2 lb (L) TSC 11" Consult Factory 3 9/16" 85.9 lb Consult Factory /16" 81.7 lb Consult Factory (L) TSC 11" 32 1/8" 88.8 lb /8" 84.6 lb Model also available in 182TC/184TC frame 27

29 MOTOR DIMENSIONS (L)1, 3 TEFC motor ODP motor 1 3 type Horsepower NEMA frame size Dimensions NEMA frame Dimensions B C H3 size B C H C 6 1/4 5 1/4 11 7/16 56C 6 1/4 5 1/ / C 6 1/4 5 1/4 11 7/16 56C 6 1/4 5 1/ / C 6 1/4 5 1/4 11 7/16 56C 6 1/4 5 1/ / C 6 1/4 5 1/4 11 7/16 56C 6 1/4 5 1/ / C 6 1/4 5 1/4 11 7/16 56C 6 1/4 5 1/ / C 6 1/4 5 1/4 11 7/16 56C 6 1/4 5 1/ / C 7 1/4 5 1/4 13 5/8 56C 6 3/16 5 1/ / C 7 1/4 5 1/4 13 5/8 56C 6 3/16 5 1/ / C 7 1/4 5 1/4 13 5/8 56C 6 3/16 5 1/ / C 7 1/4 5 1/4 13 5/8 56C 7 1/4 5 5/8 13 9/ C 7 1/4 5 1/4 13 5/8 56C 7 1/4 5 5/8 13 9/ C 7 1/4 5 1/4 13 5/8 56C 7 1/4 5 5/8 13 9/ C 7 1/4 5 1/4 13 5/8 56C 7 1/4 5 5/8 13 9/ C 7 1/4 5 1/4 13 9/16 56C 6 1/4 5 1/ / C 7 1/4 5 1/4 13 9/16 56C 6 1/4 5 1/ / C 7 1/4 5 1/4 13 9/16 56C 6 1/4 5 1/ / TC 7 3/16 5 3/4 12 1/ TC 7 3/16 5 3/4 12 1/ TC 7 3/16 5 3/4 12 1/16 Consult Factory TC 7 3/16 5 3/4 12 1/ TC 7 3/16 5 3/4 12 1/ C 6 1/4 5 1/4 11 7/16 56C 6 1/4 5 1/ / C 6 1/4 5 1/4 11 7/16 56C 6 1/4 5 1/ / C 7 1/4 5 1/4 13 5/8 56C 6 3/16 5 1/ / C 7 1/4 5 1/4 13 5/8 56C 6 3/16 5 1/ / C 7 1/4 5 1/4 13 5/8 56C 7 1/4 5 5/8 13 9/ C 7 1/4 5 1/4 13 5/8 56C 7 1/4 5 5/8 13 9/ C 7 1/4 5 1/4 13 9/16 56C 6 1/4 5 1/ / C 7 1/4 5 1/4 13 9/16 56C 6 1/4 5 1/ / C 7 1/4 5 1/4 13 9/16 56C 6 1/4 5 1/ / TC 7 1/4 5 3/ / TC 7 1/4 5 3/ / TC 7 1/4 5 3/ /16 Consult Factory TC 7 1/4 5 3/ / TC 7 1/4 5 3/ / TC 8 1/2 6 7/8 15 7/16 182TC 8 7/16 6 3/4 13 7/ TC 8 1/2 6 7/8 15 7/16 182TC 8 7/16 6 3/4 13 7/ TC 8 1/2 6 7/8 15 7/16 182TC 8 7/16 6 3/4 13 7/ TC 8 1/2 6 7/8 15 7/16 182TC 8 7/16 6 3/4 13 7/ TC 8 1/2 6 7/8 15 7/16 182TC 8 7/16 6 3/4 13 7/ TC 8 1/2 6 7/8 15 7/16 182TC 8 7/16 6 3/4 13 7/ TC 8 1/2 6 7/8 15 7/16 182TC 8 7/16 6 3/4 13 7/8 NOTE: Motor dimensions (B, C and H3) are provided for reference only and should be verified based on motor manufacturer specifications. 28

30 MOTOR DIMENSIONS (L) 5, 1, 15, 2 29

31 EVMU(G)(L) TECHNICAL DATA DIMENSIONS MODELS EVMUL32 1 EVMUL EVMUL EVMUL45 3 EVMUG32 1 EVMUG EVMUG EVMUG45 3 Approximate Motor Dimensions C* for 3 phase, TEFC, NEMA Motors HP Frame Size 184TC 184TC C* Inches Motor Wt LBS TC 215TC 256TC Note: C* may vary slightly by manufacturer C* G 3/8'BSPP G 3/8'BSPP Flange Detail: EVMU /2" 15Lb. ANSI EVMU45 3" 15Lb. ANSI Refer to page 33 for dimension details. 3

32 EVMU(G)(L) TECHNICAL DATA DIMENSIONS MODELS EVMUG EVMUG64 3 EVMUL EVMUL64 3 Approximate Motor Dimensions C* for 3 phase, TEFC, NEMA Motors HP Frame Size C* Inches Motor Wt LBS TC 215TC 256TC 284TSC 286TSC 324TSC Note: C* may vary slightly by manufacturer C* G 3/8'' BSPP G 3/8'' BSPP Flange Detail: EVMU64 4" 15Lb. ANSI Refer to page 33 for dimension details. 31

33 EVMU(G)(L) TECHNICAL DATA DIMENSIONS MODELS EVMUG32 5 EVMUG EVMUG EVMUG EVMUG EVMUG64 4 EVMUL32 5 EVMUL EVMUL EVMUL EVMUL EVMUL64 4 Approximate Motor Dimensions C* for 3 phase, TEFC, NEMA Motors HP Frame Size C* Inches Motor Wt LBS TC 284TSC 286TSC 324TSC 326TSC Note: C* may vary slightly by manufacturer C* G 3/8'' BSPP G 3/8'' BSPP Flange Detail: EVMU /2" 3Lb. ANSI EVMU45 3" 3Lb. ANSI EVMU64 4" 3Lb. ANSI Refer to page 34 for dimension details. 32

34 EVMU(G)(L) DIMENSION TABLE Model Type HP 5 7 1/ / Lbs Motor Frame* 184TC 184TC 215TC 215TC 215TC 256TC 284TSC 286TSC 286TSC 324TSC 324TSC 184TC 215TC 215TC 256TC 284TSC 286TSC 324TSC 326TSC 326TSC 215TC 215TC 256TC 284TSC 286TSC 324TSC 324TSC 326TSC PL 18 3/ / / / / / / / / / / / / / / / / / / / / /4 32 3/ / / /64 H 4 9/ / /64 Dimensions (inches) G ST SA SG SF SD SN 25/ / /32 2 9/ /64 1 1/16 7 1/2 3/4-1UNC 8 15/16 7 1/2 25/ /8 3 5/ / /64 8 1/4 29/ / / /8 3 15/ / / /32 Model Type HP 5 7 1/ / Motor Frame* 184TC 184TC 215TC 215TC 215TC 256TC 284TSC 286TSC 286TSC 324TSC 324TSC 184TC 215TC 215TC 256TC 284TSC 286TSC 324TSC 326TSC 326TSC 215TC 215TC 256TC 284TSC 286TSC 324TSC 324TSC 326TSC *Motor frame for Three Phase TEFC only. Consult factory for single phase and alternate enclosures. SE 5 1/2 5 7/ /8 7 1/2 7 7/8 BM 6 11/ / /64 BY1 9 29/ / /32 Dimensions (inches) BL 8 17/ / /64 BW 11 1/ / /32 BF 35/64 35/64 35/64 BH 1 3/8 1 49/ /64 Bare only. 33

35 SECTIONAL VIEW (L)1 with Round (ANSI) flange (F) 34

36 PIPE CONNECTION (L)1 with Loose round flange (LF) with Oval flange (N) with victaulic connection (V) with Clamp connection (C) 35

37 SECTIONAL VIEW PART REFERENCE (L)1 N PART NAME MATERIAL DIMENSIONS L [mm] STANDARD 4 Casing cover 5-1 Suction casing 5-2 Intermediate Casing 5-3 Intermediate casing bearing 5-4 Discharge casing 6 Bottom casing 7 Outer casing AISI 316L (EN 1.444) 21 Impeller 31 Shaft AISI 316L (EN 1.444) 32-1 Adjuster Key 43-2 Shaft sleeve (intermediate) AISI 316L (EN 1.444) 12x Shaft sleeve (bearing) 43-5 Shaft sleeve (last stage) 43-7 Spacer AISI 316L (EN 1.444) 12x Shaft sleeve bearing Tungsten carbide 45 Flange holder 46 Ring (mechanical seal) AISI 316L (EN ) 47 Ring Holder 48 Impeller nut A2-7 UNI 7323 with inox insert A4-7UNI7323withinoxinsert M Bearing Tungsten carbide 75 O-Ring (plug) D x2.62 OR O-Ring (plug) 17 Liner ring + PPS + PPS 111 Mechanic alseal SiC/Carbon/FP /FP PM Mechanical seal seat Seal holder Mechanical seal cartridge O-Ring (outer casing) D x5.34 OR O-Ring O-Ring (cartridge sleeve) D x2.62 OR O-Ring (seal cover) D x2.62 OR Tie-rod Galvanized steel 6.8 class ISO 898/1 M Screw A2-7 UNI 7323 M4x1 ISO Screw for coupling Galvanized steel M6x25 ISO Screw for counterflange A2-7 UNI Nut fortierod Galvanized steel M1 UNI Nut for tierod A2-7 UNI 7323 M1 UNI Nut forcoupling Galvanized steel M6 ISO Set screw A2-7 UNI 7323 M5x8 UNI Screw for coupling guard A2-7 UNI 7323 M5x6 UNI Pin forshaft Carbon Steel D. 4x32 UNI Washer Galvanized steel D. 1.5x21x2 UNI Washer Carbon Steel Ø Impeller spacer 14 Coupling up to 5 HP Die cast Aluminium EN AB-AISI11Cu2 (Fe) 16 Base Die cast Aluminium EN AB-AISI11Cu2 (Fe) 162 Motor bracket Cast iron EN-GJL-2 -EN Plug Plug Venting plug AISI 316L (EN ) 219 Counter flange 245 Coupling guard Plug Washer 615 Flange Nodular Cast Iron 36

38 PART QUANTITY FOR MODEL (L)1 Type (L) / / 1 (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) N ** * / / / / / / / / / / / / / / / / / / / / / / / / / 1 1 / / 1 1 / / 1 1 / / 1 1 / / 1 1 / / 1 1 N Type * * ** (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) (L) / / (L) / / (L) / / (L) / / (L) / / (L) / / * only for Oval flange (N) ** only for Loose round flange (LF) 37

39 SECTIONAL VIEW (L)3 with Round (ANSI) flange (F) 38

40 PIPE CONNECTION (L)3 with Loose round flange (LF) with Oval flange (N) with victaulic connection (V) with Clamp connection (C) 39

41 SECTIONAL VIEW PART REFERENCE (L)3 N PART NAME MATERIAL DIMENSIONS L [mm] STANDARD 4 Casing cover 5-1 Suction casing 5-2 Intermediate Casing 5-3 Intermediate casing bearing 5-4 Discharge casing 6 Bottom casing 7 Outer casing AISI 316L (EN 1.444) 21 Impeller 31 Shaft AISI 316L (EN 1.444) 32-1 Adjuster Key 43-2 Shaft sleeve (intermediate) AISI 316L (EN 1.444) 43-3 Shaft sleeve (bearing) 43-5 Shaft sleeve (last stage) 43-7 Spacer 12x Shaft sleeve bearing Tungsten carbide 45 Flange holder 46 Ring (mechanical seal) AISI 316L (EN ) 47 Ring Holder 48 Impeller nut A2-7 UNI 7323 with inox insert A4-7UNI7323withinoxinsert M Bearing Tungsten carbide 75 O-Ring (plug) D x2.62 OR O-Ring (plug) 17 Liner ring + PPS + PPS 111 Mechanic alseal SiC/Carbon/FP / Mechanical seal seat Seal holder Mechanical seal cartridge O-Ring (outer casing) D x5.34 OR O-Ring O-Ring (cartridge sleeve) D x2.62 OR O-Ring (seal cover) D x2.62 OR Tie-rod Galvanized steel 6.8 class ISO 898/1 M Screw A2-7 UNI 7323 M4x1 ISO Screw for coupling Galvanized steel M6x25 ISO Screw for counterflange A2-7 UNI Nut fortierod Galvanized steel M1 UNI Nut for tierod A2-7 UNI M1 UNI Nut forcoupling Galvanized steel M6 ISO Set screw A2-7 UNI 7323 M5x8 UNI Screw for coupling guard A2-7 UNI 7323 M5x6 UNI Pin forshaft Carbon Steel D. 4x32 UNI Washer Galvanized steel D. 1.5x21x2 UNI Washer Carbon Steel Ø Impeller spacer 14 Coupling up to 5 HP Die cast Aluminium EN AB-AISI11Cu2 (Fe) 16 Base Die cast Aluminium EN AB-AISI11Cu2 (Fe) 162 Motor bracket Cast iron EN-GJL-2 -EN Plug Plug Venting plug AISI 316L (EN ) 219 Counter flange 245 Coupling guard Plug Washer 615 Flange Nodular Cast Iron 4