TRIPLE-ECCENTRIC BUTTERFLY VALVES TYPE L32.8
|
|
|
- Tracey Ford
- 5 years ago
- Views:
Transcription
1 α TRIPLE-ECCENTRIC UTTERFLY VALVES TYPE L32.8 Application Triple-eccentric butterfly valves are industrial valves, which designed to fully open or close the passage of the working medium flowing through a pipeline. They can also be used for flowcontrol purposes. However, the tightness of the valve cannot be guaranteed in a long-term use for control purposes. Working medium waste and service water drinking water hot water steam non-aggressive liquids and gases (natural gas, co-gas, petroleum products, etc.). Maximum working temperature A maximum working temperature of the butterfly valve is +400 C, by agreement up to +550 C and depends on the body material used. Technical description Triple eccentricity - Fig. A 1. the operating shaft axe is eccentric to the packing axis 2. the operating shaft axe is eccentric to the axis of the flow 3. the axe of the seat cone is eccentric to the axis of the flow Triple eccentricity assures, that the packing stays out of sealing surface of the body except for the closed position, which results in long life-time of the packing (sealing) and lots of cycles. The triple eccentricity design immediately divides the disc from the sealing surface and when closing the valve the disc touches sealing surface just before closure. y this is the closing and opening torque lower and the opening and closing of the valve is done by very little friction. This makes the valves life-time longer. utterfly valve is both-side tight. The arrow stamped on the valve body corresponds with the direction of the long-term tightness. Stems of the butterfly valves manufactured according to TA-Luft standard or in compliance with Fugitive Emission are tightened through the Quick set seal from Garlock company. The butterfly valves are produced of wrought or cast material. Seal material is metal x metal or metal x graphite seal ring. Operation manual gear-box electric actuator pneumatic or hydraulic actuator remote control from stand Testing The valves are tested according to EN EN EN Connection to piping wafer type acc. to EN , face to face dimensions acc. to EN 558-1, Series 16, 20, 25 flanged ends acc. to EN , face to face dimensions acc. to EN 558-1, Series 13, 14, 16 welded ends acc. to ČSN , EN , face to face dimensions acc. to EN 558-1, Series 14 Other face to face and connecting dimensions are acc. to the customer s requierement, e.g. GOST, ANSI. Installation The butterfly valves can be mounted into horizontal, vertical or inclined pipeline so that the arrow stamped on the valve body corresponds with the direction of the tightness (arrow points from higher pressure to lower when the disc is closed), and the rotating axe of the disc is in a horizontal position. The bolt type at the pivot area is also very important. When there is a butterfly valve with electric actuator it is important to abide the actuator s manufacturer. Fig. A Fig. Spiral Fig. C metal seal Overlay on the seat Metal seal ring earing Gland ring 2. Eccentricity 1. Eccentricity α α = 3. Eccentricity Seal earing O-ring 20
2 TRIPLE-ECCENTRIC UTTERFLY VALVES TYPE L32.8 DN PN Tmax +400 C Design: wrought DN PN Tmax 550 C EN WAFER TYPE (for wrought design) EN FLANGED ENDS (for cast design) Wrought design Position Cast design Component Standard acc. to EN Material variants acc. to EN Material variants acc. to ASTM Carbon + alloy steel Stainless steel Carbon + alloy steel Stainless steel +400 C* +500 C* +500 C* +400 C* +500 C* +500 C* 1 ody A105 A182 F12 A182 F316 2 Disc A105 A182 F12 A182 F316 3 Seat 17%Cr, stellite stellite stellite 17%Cr, stellite stellite stellite 4 Shaft steell 13%Cr A479 XM19, , A182 F6 A479 XM19 A182 F316 * Temperature application depends on the seal of valve and pressure-temperature material characteristics. Design for temperature higher than 500 C is possible after agreement with the manufacturer. Position Component Standard Material variants acc. to ASTM +400 C* -46 C to 300 C +550 C +500 C* +550 C 1 ody A216 WC A352 LC A217 WC6 A351 CF8 A351 CF8M A216 WC A352 LC A217 WC6 A351 CF8 A351 CF8M 2 Disc stainless steel overlay (stellite on customer s request) stainless steel overlay (stellite on customer s request) 4 Shaft A A (AMS) A A Cr13 Cr13 24CrMo4 18Cr-8Ni 17Cr-4Ni-4Cu 5 Seal A graphite A graphite A graphite A graphite A graphite 17Cr-7Ni+graphite 17Cr-7Ni+graphite 17Cr-7Ni+graphite 18Cr-8Ni+graphite 16Cr-12Ni-2Mo+graphite * Temperature application depends on the seal of valve and pressure-temperature material characteristics. Production range Wrought design Cast design Wafer type Flanged ends Wafer type Welded ends DN PN PN PN PN
3 TRIPLE-ECCENTRIC UTTERFLY VALVES TYPE L32.8 DN PN Tmax +400 C Design: wrought EN WAFER TYPE L F (ISO 5211) d1 n x d 4 x M D2 D1 f DN D3 A l1 PN 16 DN A L F D1 D2 D3 d1 f M n x d l1 kg M20 4 x M20 8 x M24 8 x M24 8 x M24 12 x M27 12 x M30 16 x M33 16 x PN 25 DN A L F D1 D2 D3 d1 f M n x d l1 kg M24 4 x M24 8 x M27 8 x M27 12 x M30 12 x M33 12 x M33 16 x M36 16 x PN 40 DN A L F D1 D2 D3 d1 f M n x d l1 kg M24 4 x M27 8 x M30 8 x M30 12 x M33 12 x M36 12 x M39 16 x M45 16 x * DN on request 22
4 TRIPLE-ECCENTRIC UTTERFLY VALVES TYPE L32.8 DN PN Tmax 550 C EN FLANGED ENDS A F ISO 5211 L d1 I1 DN D3 D1 section D-D a f n x d D 4 x M D2 PN 6 DN A L D1 D2 D3 a f d1 l1 F n x d M kg F10 4 x 18-28, F10 4 x 18-36, F10 8 x 18-44, F12 8 x F12 8 x F12 12 x F14 12 x F16 12 x F16 16 x F16 16 x F25 20 x F25 20 x F25 24 x F30 24 x F30 24 x F30 24 x 30 M
5 TRIPLE-ECCENTRIC UTTERFLY VALVES TYPE L32.8 DN PN Tmax 550 C PN 10 EN FLANGED ENDS DN A L D1 D2 D3 a f d1 l1 F n x d M kg F10 8 x F10 8 x F10 8 x F12 8 x F12 8 x F12 12 x F14 12 x F16 16 x F16 16 x F16 20 x F25 20 x F25 20 x F25 24 x F30 24 x F30 28 x F30 24 x 36 M PN 16 DN A L D1 D2 D3 a f d1 l1 F n x d M kg F10 8 x F10 8 x F10 8 x F12 8 x F12 12 x F14 12 x F16 12 x F16 16 x F25 16 x F25 16 x 30 M F25 16 x 33 M F30 16 x 36 M F30 20 x 36 M F30 20 x 39 M F40 24 x 39 M F40 24 x 42 M PN 25 DN A L D1 D2 D3 a f d1 l1 F n x d M kg F10 8 x F10 8 x F10 8 x F12 8 x F12 8 x 26 M F14 8 x 30 M F16 12 x 30 M F16 12 x 33 M F25 12 x 36 M F25 16 x 36 M F25 16 x 36 M F30 16 x 39 M F30 20 x 42 M F30 20 x 48 M F40 24 x 48 M F40 24 x 56 M
6 TRIPLE-ECCENTRIC UTTERFLY VALVES TYPE L32.8 DN PN Tmax 550 C PN 40 EN FLANGED ENDS DN A L D1 D2 D3 a f d1 l1 F n x d M kg F10 8 x 18-35, F10 8 x 22-47, F12 8 x F12 8 x F14 12 x F16 12 x F25 16 x F25 16 x F25 16 x F30 16 x 39 M F30 16 x 42 M F30 16 x 48 M F40 20 x 48 M F40 20 x 56 M PN 63 DN A L D1 D2 D3 a f d1 l1 F n x d M kg F10 8 x 22-35, F10 8 x 26-47, F12 8 x F16 8 x F16 8 x 36 M F25 8 x 36 M F25 12 x 36 M F25 12 x 39 M F30 12 x 42 M PN 100 DN A L D1 D2 D3 a f d1 l1 F n x d M kg x 26 M F12 4 x 30 M F14 4 x 33 M F16 8 x 33 M F25 8 x 36 M F25 8 x 39 M F30 12 x 42 M F30 12 x 48 M F30 12 x 48 M
7 TRIPLE-ECCENTRIC UTTERFLY VALVES TYPE L32.8 DN PN 6-40 Tmax 550 C EN WAFER TYPE F ISO 5211 L d1 DN D3 A l1 n x d (M) D2 PN 6 DN A L D2 D3 d1 l1 F M kg F10-7, F10-10, F10-19, F F12 M F12 M F14 M F16 M F16 M F16 M F25 M F25 M F25 M F30 M F30 M F30 M
8 TRIPLE-ECCENTRIC UTTERFLY VALVES TYPE L32.8 DN PN 6-40 Tmax 550 C EN WAFER TYPE PN 10 DN A L D2 D3 d1 l1 F M kg F10-13, F10-15, F10-22, F F12 M F12 M F14 M F16 M F16 M F16 M F25 M F25 M F25 M F30 M F30 M F30 M PN 16 DN A L D2 D3 d1 l1 F M kg F10-13, F10-15, F10-22, F F12 M F14 M F16 M F16 M F25 M F25 M F25 M F30 M F30 M F30 M F40 M F40 M
9 TRIPLE-ECCENTRIC UTTERFLY VALVES TYPE L32.8 DN PN 6-40 Tmax 550 C EN WAFER TYPE PN 25 DN A L D2 D3 d1 l1 F M kg F10-15, F10-17, F10-26, F F12 M F14 M F16 M F16 M F25 M F25 M F25 M F30 M F30 M F30 M F40 M PN 40 DN A L D2 D3 d1 l1 F M kg F10-20, F10-30, F F F14 M F16 M F25 M F25 M F25 M F30 M F30 M F30 M
10 TRIPLE-ECCENTRIC UTTERFLY VALVES TYPE L32.8 DN PN Tmax 550 C EN WELDED ENDS A F ISO 5211 L d1 I1 d1 DN D3 D1 PN 16 DN A L D1 D3 d1 l1 F kg F10 25, F10 32, F10 39, F F F F F F F F F F F F F
11 TRIPLE-ECCENTRIC UTTERFLY VALVES TYPE L32.8 DN PN Tmax 550 C EN WELDED ENDS PN 25 PN 40 PN 63 PN 100 DN A L D1 D3 d1 l1 F kg F10 25, F10 32, F10 39, F F F F F F F F F F F F F DN A L D1 D3 d1 l1 F kg F10 25, F10 32, F F F F F F F F F F DN A L D1 D3 d1 l1 F kg F F F F F F F F F DN A L D1 D3 d1 l1 F kg F F F F F F F F
COMPANY PROFILE TABLE OF CONTENT. Our products have been supplied to local and foreign customers for the following industries:
UTTERFLY VALVES TALE OF CONTENT COMPANY PROFILE The company ARMATURY Group a.s. is a leading Czech manufacturer and distributor of industrial valves, fittings and control systems for valves. The annual
DOUBLE-ECCENTRIC BUTTERFLY VALVES TYPE L32.7
DOULE-ECCENTRIC UTTERFLY VALVES TYPE L32.7 Application Double-eccentric butterfly valves are industrial valves, which are designed to fully open or close the passage of the working medium flowing through
SINGLE-ECCENTRIC BUTTERFLY VALVES TYPE L32.6
Application Single-eccentric butterfly valves are industrial valves, which are designed to fully open or close a passage of the working medium flowing through a pipeline. They can also be used for flow-control
DOUBLE-ECCENTRIC BUTTERFLY VALVES TYPE L32.7
Application Double-eccentric butterfly valves are industrial valves, which are designed to fully open or close the passage of the working medium flowing through a pipeline. They can also be used for flow-control
SINGLE-ECCENTRIC BUTTERFLY VALVES TYPE L32.6
Application Single-eccentric butterfly valves are industrial valves, which are designed to fully open or close a passage of the working medium flowing through a pipeline. They can also be used for flow-control
STEAM EXTRACTION / COLD REHEAD ACTUATED CHECK VALVES
STEAM EXTRACTION / COLD REHEAD ACTUATED CHECK VALVES More than 20 years of experience in design and manufacturing and service of custom made actuated Steamextraction Check valves for the Power Generation
EXTRACTION CHECK VALVES TYPE C09.6
Application Extraction check valves are valves used to to prevent the back flow of the service fluid in extraction and bleed lines of steam turbines. Each extraction check valve is designed exactly for
ALC-3 BUTTERFLY VALVES NOMINAL PRESSURE NOMINAL SIZE MATERIALS CONNECTIONS DESIGN. ANSI Class PN DN
BUTTERFLY VALVES ALC-3 NOMINAL PRESSURE ANSI Class 150-600 PN 10-100 NOMINAL 2-80 DN 50-2000 MATERIALS Cast Iron Carbon Steel Low Alloy Steel CONNECTIONS Wafer Lugged Flanged Butt Weld DESIGN Eccentric
Triple Eccentric Control and Shut-off Butterfly Valve Series 14t
Application: Triple Eccentric Control and Shut-off Butterfly Valve Series 14t Triple eccentric butterfly valve providing excellent shut-off in all industrial applications: Nominal size DN 80 to DN 400
GATE VALVES S 38 APPLICATION
APPLICATION The gate valves of this design are controlled valves used as the shut-off units in the piping system. They can be used for water, saturated and superheated steam, gases, non-aggressive liquids,
R o L. BUTTERFLY VALVE of carbon steel with flanges series BLUE LINE. Operation. Edition
of carbon steel 31500 series C ont R o L Operation Edition 03-0-009 The welded butterfly valve 31500 is used for example in district heating, district cooling and industry. It can be used as an on-off
R o L. BUTTERFLY VALVE of carbon steel with welded ends 313 -series BLUE LINE. Description
of carbon steel 313 -series C ont R o L Description Edition 23-07-2015 The welded butterfly valve 313 is specially designed for district heating and district cooling. It can be used as an on-off or control
BROEN Butterfly valves
BROEN Butterfly valves Triple eccentric butterfly valves BROEN Butterfly valves Application Butterfly valves type BROEN are used as a shut-off valves and regulating valves in many different applications:
High-pressure shut-off globe valve V30 High-pressure shut-off globe valve with control cone V40 PN , DN , T max : 550 C
High-pressure shut-off globe valve V30 High-pressure shut-off globe valve with control cone V40 PN 63-160, DN 50 150, T max : 550 C Shut-off globe valve (series V30) or shut-off globe valve with control
Rate B standard. Rate A Rate A option. max +260 C/ min -40 C
of carbon steel 315 -series C ont R o L Description Edition 30-03-2015 The welded butterfly valve 315 is used for example in district heating, district cooling and industry. It can be used as an on-off
Type K03. Gate Valve Butt-Welded, Flanged DN PN Data Sheet Edition: EN 9 / together we are strong
PN 16 100 Gate Valve Butt-Welded, Flanged Data Sheet Edition: EN 9 / 2015 MPOWER Engineering, a.s. Pod vinicí 2028/20, Modřany, 143 00 Praha 4, CZ T: +420 225 371 300, F: +420 225 371 325 E: info@mpowergroup.eu,
Sealing Test Pressure (MPa)
TRIPLE ECCENTRIC BUTTERFLY VALVE Triple Eccentric Butterfly Valve provides a tight shut-off. This geometry ensures that the disc seal contacts the body seat only at the final shut-off position without
BUTTERFLY VALVE WAFER TYPE stainless steel 411 (41000) series PN40 For steam (fire safe versions) and 41001
Operation WAFER TYPE stainless steel 411 (41000) series PN40 For steam (fire safe versions) 41101 and 41001 C ont R o L Description Edition Wafer type butterfly valve 411 (410) series are used in industrial
HIGH PERFORMANCE BUTTERFLY VALVE MODEL HP300 SERIES
FEATURES AND BENEFITS Wafer & Lugged bodied butterfly valves for bi-directional use Dead end service are offered as standard in full ANSI Class and ratings (for lugged design only) The design of double
BUTTERFLY VALVE WAFER TYPE of carbon steel ( ) series
Operation WAFER TYPE of carbon steel 1100 (1000-100) series C ont R o L Operation Edition 0-0-009 Wafer type butterfly valve 1100 (1000 100) series is used in industrial pipelines for demanding on-off
BUTTERFLY VALVE WAFER TYPE of carbon steel 311 ( ) series
Operation WAFER TYPE of carbon steel 311 (310-312) series C ont R o L Description Edition 23-07-2015 Wafer type butterfly valve 311 (310 312) series is used in industrial pipelines for demanding on-off
VES AL Y V BUTTERFL 60
BUTTERFY VAVES 60 ANSI HIGH PERFORMANCE BUTTERFY VAVES High Performance Butterfly Valves Sealing principle of b eccentric HPBV Zero Offset: Concentric valve (zero offset). Disc rotates around the centre
16 bar standard 25 bar - option Tightness class ISO 5208, EN Standard - RATE B, Option RATE A RATE A. 16 bar standard 25 bar - option
Operation WAFER TYPE stainless steel C ont R o L Description Edition Wafer type butterfly valve is an on-off and control valve for demanding industrial pipelines. The valve is tight to both directions
RAIMONDI. High pressure forged globe valves to guarantee the pressure envelope integrity on harsh services.
Fig. 6022-6025 RAIMONDI High pressure forged globe valves to guarantee the pressure envelope integrity on harsh services. Features Forged body materials of highest quality, all in compliance with ASME
The series 10 butterfly valves has been developed for a large number of applications throughout process industries. The
Technical Bulletin B-100 Features Series 10 High Performance Feature Butterfly valves For Rating ANSI 150 General : The series 10 butterfly valves has been developed for a large number of applications
BUTTERFLY VALVE TRIPLE ECCENTRIC BUTTERFLY VALVE
Triple Eccentric Butterfly Valve provides a tight shut-off performance. This geometry ensures that the disc seal contacts the body seat only at the final shut-off position without rubbing or galling, providing
Flowserve TX2 Butterfly Valves Triple Offset TECHNICAL BULLETIN FCD DVENTB
Flowserve TX2 Butterfly Valves Triple Offset TECHNICAL BULLETIN FCD DVENTB0400-00 1 TABLE OF CONTENTS PAGE Theory of Operation.. 3 General Ordering Information 4 Torque values ASME Cl. 150. 5 Torque values
Gate valve S38 PN , DN , T max : 540 C
Gate valve S38 40-100, DN 40 400, T max : 540 C Shut off gate valve with outsidescrew, rising stem, non-rising hand wheel, with bolted bonnet, with flanges or with butt weld ends, flexible or split wedge,
NELES HIGH PERFORMANCE TRIPLE ECCENTRIC DISC VALVE, METAL SEATED NELDISC SERIES L12
NELES HIGH PERFORMANCE TRIPLE ECCENTRIC DISC VALVE, METAL SEATED NELDISC SERIES L12 Metso's Neles Neldisc series L12 a wafe type, metal seated high performance triple eccentric disc valve. With close to
BROEN BUTTERFLY VALVES
BROEN BUTTERFLY VALVES 1 Climate change is our common challenge Energy efficiency is one of the greatest challenges of our times and for district energy BROEN delivers ready solutions to meet the globally
BALL SECTOR VALVE of stainless steel 455 series
C ont R o L Description Edition Högfors ball sector valve series 55 is specially designed for control applications of various media like liquids, pulps and steam. 55KC is used for sticky and crystallizing
Butterfy valves 4 offset DN65 up to DN2500 / PN2,5 up to PN160 / Class 150 up to Class 900
EN utterfy valves 4 offset N up to N0 / PN2,5 up to PN / Class 1 up to Class 0 utterfly valves 4 offset N up to N0 / PN2,5 up to PN Main application The range of application depends directly on materials,
FASANI PRESSURE SEAL CAST GLOBE VALVES - STYLE B Y AND T PATTERN
A wide range of globe valves specifically designed for high pressure and high temperature applications, where low pressure loss is required. FEATURES GENERAL APPLICATION Our pressure seal globe valves
METAL SEATED NELES ZEROLEAK NELDISC BUTTERFLY VALVES, SERIES L1 & L2
METAL SEATED NELES ZEROLEAK NELDISC BUTTERFLY ALES, SERIES L & L Neldisc series L is a wafer type and series L a lug type metal seated high performance butterfly valve. With close to equal percentage characteristics
The globe valves are used as a closing valve for: - noncorrosive fluids - saturated steam
The globe valves are used as a closing valve for: - noncorrosive fluids - saturated steam - oil - air - petroleum and petroleum products The Characteristics of working conditions: pressure dependency on
The excellent performance of the pressure seal type range, is optimal in high pressure and high temperature applications.
The excellent performance of the pressure seal type range, is optimal in high pressure and high temperature applications. Features Swing check valves can fit on both horizontal and vertical (up-flow) piping.
BR 14b / BR 14c Application:
High - Performance Butterfly valve BR 14b / BR 14c Application: Tight-closing, double-eccentric butterfl y control valve especially for the chemical industry where aggressive media s are used, for example
PRZEPUSTNICE. B-599 Centric butterfly valve PN16 from -10ºC to +130ºС DN32 DN200 PN-EN 2-3
BUTTERFLY VALVES PRZEPUSTNICE TYPE DESCRIPTION NOMINAL PRESSURE TEMPERATURE DIAMETER STANDARD PAGE B-599 Centric butterfly valve PN16 from -10ºC to +130ºС DN32 DN200 PN-EN 2-3 B-099 Centric butterfly valve
The series 10 butterfly valves has been developed for a large number of applications throughout process industries. The
Technical Bulletin B-100 Features Series 10 High Performance Feature Butterfly valves For Rating JIS 20K General : The series 10 butterfly valves has been developed for a large number of applications throughout
RAIMONDI. High pressure forged check valves recommended to prevent flow reversal in severe applications.
Fig. 6042 6045 RAIMONDI High pressure forged check valves recommended to prevent flow reversal in severe applications. Features High quality forged materials to guarantee pressure envelope integrity, all
NELES HIGH CAPACITY TRIPLE ECCENTRIC DISC VALVE, METAL SEATED NELDISC SERIES L6
NELES HIGH CAPACITY TRIPLE ECCENTRIC DISC ALE, METAL SEATED NELDISC SERIES L6 Metso's Neles series L6 is a double flanged metal seated Neldisc triple eccentric disc valve with one piece body design, for
ABsOlute flow control. SERIES 3E // DN (6-16 ) // Oil & Gas // Power Generation // Petrochemistry
ABsOlute flow control SERIES 3E // DN 150-400 (6-16 ) // Oil & Gas // Power Generation // Petrochemistry TRIPLE OFFSET BUTTERFLY VALVES GENERAL INFORMATION GENERAL CHARACTERISTICS Triple offset design
VANESSA SERIES 30,000 TRIPLE OFFSET VALVES* BASIC CONFIGURATION
* BASIC CONFIGURATION With a robust integral-to-body valve seat and optimized seating angles, this valve is capable of handling isolation and process control through multiple functionalities FEATURES GENERAL
technical description:
The gate valves are used as the closing valves for: - noncorrosive fluids - saturated steam - oil - air - petroleum and petroleum products Operating parameters are in accordance with the standard ASME
METSO NELES HIGH PERFORMANCE VALVE, METAL SEATED SERIES BW
METSO NELES HIGH PERFORMANCE VALVE, METAL SEATED SERIES BW Neles BW series metal seated high performance butterfly valve with one piece body design, for both control and tight shut-off applications. Multiple
EXTRACTION CHECK VALVES
EXTRACTION CHECK VALVES COMPANY PROFILE The company ARMATURY Group a.s. is a leading Czech manufacturer and distributor of industrial valves, fittings and control systems for valves. The annual production
BR 10a Control and Shut-off Butterfly valve
M-PTFE lined double-eccentric BR 10a Control and Shut-off Butterfly valve Application: Tight-closing, double-eccentric butterfl y control valve with M-PTFE lining for process engineering and plants with
COMPANY PROFILE. Our products have been supplied to local and foreign customers for the following industries:
CECK VAVES COMPANY PROFIE The company ARMATURY Group a.s. is a leaing Czech manufacturer an istributor of inustrial valves, fittings an control systems for valves. The annual prouction is of more than
marine cargo systems Edition:
Butterfly valves for Si-206 EN marine cargo systems Edition: 2007-05 Type MTV Type MTVL Wafer design Lugged design Nominal pressure PN 10-25 ANSI 150 Nominal size DN 80-400 Material Stainless steel The
GWC Italia. Proven technology for individual valve solutions worldwide HIGH PERFORMANCE BUTTERFLY VALVE HPB-1003
w w w. g w c i t a l i a. c o m GWC Italia Proven technology for individual valve solutions worldwide HIGH PERFORMANCE BUTTERFLY VALVE HPB-1003 1 1 GWC ITALIA Proven technology for individual valve solutions
Technical changes kept in reserve THROUGH CONDUIT KNIFE GATE VALVE
Technical changes kept in reserve THROUGH CONDUIT KNIFE GATE VALVE The B model knife gate is a bi-directional wafer valve designed for media with high consistency. The double seat design assures a non-clogging
Lined Butterfly Valve Pfeiffer Type BR 10a
Lined Butterfly Valve Pfeiffer Type BR 10a Application Tight closing, double eccentric butterfly valve with PTFE lining for process engineering and plants with industrial requirements, especially suitable
TRUNNION MOUNTED BALL VALVES
TRUNNION MOUNTED BALL VALVES COMPANY PROFILE The company ARMATURY Group a.s. is a leading Czech manufacturer and distributor of industrial valves, fittings and control systems for valves. The annual production
R o L. WAFER PATTERN V-PORT BALL VALVE stainless steel 465 series SILVER LINE. Operation. Description. Edition
Operation WAFER PATTERN V-PORT BALL VALVE stainless steel C ont R o L Description Edition Högfors ball sector valve series 465 is specially designed for control applications of various medium like liquids,
Bolted bonnet configuration
The bolted bonnet type valves are manufactured to guarantee the highest performance in the widest spectrum of oil and gas applications Features Swing check valves can fit on both horizontal and vertical
butterfly valves high performance TRIPLE OFFSET HP-TRI REV0
high performance EXECUTION 1st OFFSET 2nd OFFSET 3rd OFFSET The BELVEN-TRI series incorporate triple offset disc configuration. With this configuration the disc seal makes contact with body seat, only
Triple Offset Valves
Triple Offset Valves FLOWSEAL MS Value Statement For the harsh conditions of critical process applications, steam isolation, high cycle frequency, and temperature extremes, the Flowseal MS triple-offset
BALL SECTOR VALVE of stainless steel 455 (459) series
Operation C ont R o L Description Edition Högfors ball sector valve series 55 is specially designed for control applications of various media like liquids, pulps and steam. 55KC is used for sticky and
HOPPER SHAPE KNIFE GATE VALVE
HOPPER SHAPE KNIFE GATE VALVE The C model knife gate is a uni-directional wafer valve designed for industrial bulk handling service applications (powdered and granular products). makes it ideal for use
ITEM DESCRIPTION FIGURE STOP VALVES
INDEX OF STEEL INDUSTRIAL VALVES ITEM DESCRIPTION FIGURE STOP VALVES 01. STRAIGHT PATTERN STOP VALVES PN 40 DN 15-250 for general application ZPZ 1 with control disc for general application ZPR 1 for petroleum
Materials : Carbon steel or stainless steel
Size : Ends : Min Temperature : Max Temperature : DN 50 to 600 mm Between PN25 flanges - 29 C + 210 C Max Pressure : 25 Bars Specifications : Double eccentric Wafer type Fire safe according to ISO 10497
Series 14b - Type HD
High-Performance Control and Shut-off Butterfly Valve Series 14b - Type HD Application: Tight-closing, double-eccentric butterfl y valve especially for high requirements in the chemical industry, for example
WAFER STYLE KNIFE GATE VALVE
WAFER STYLE KNIFE GATE VALVE The model knife gate is an uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging shut off on
Materials : Carbon steel or stainless steel
Size : Ends : Min Temperature : Max Temperature : DN 50 to 350 mm Between flanges GN 25-20 C + 210 C Max Pressure : 25 Bars Specifications : Double eccentric Wafer type Fire safe according to API 607 Iso
Series 30,000 Rotary Process Valve. Technical data API 609, DIN 3840.
Series 30,000 Rotary Process Valve The outstanding performance of triple offset, metal seated Vanessa Series 30,000 valve is the ideal solution to achieve perfect shutoff in any process. Features Torque
BUTTERFLY VALVE - 18/28 SERIES Pneumatic actuator - El-O-Matic
B C D FIGURE: PD: Pneumatic actuator, double acting PE: Pneumatic actuator, spring return BUTTERFLY VALVE - 18/28 SERIES Pneumatic actuator - El-O-Matic G F L The pneumatic actuator is calculated for 6
Butterfly Valve TRIODIS 150. Triple-offset Butterfly Valve DN (2"-56") Class 150 Metal Seat. Type Series Booklet
Butterfly Valve Triple-offset Butterfly Valve DN 50-1400 (2"-56") Class 150 Metal Seat Type Series Booklet Legal information/copyright Type Series Booklet All rights reserved. The contents provided herein
Wafer, Semi Lug, Lug and Flanged Type
Year : Wafer, Semi Lug, Lug and Flanged Type Page 1 Year : Specification Description : GVC concentric rubber lined butterfly valves suitable for bi-directional flow and bubble tight shut-off at full rated
MADE OF STAINLESS...
MADE OF STAINLESS... Size : Ends : Min Temperature : Max Temperature : DN 50 to 600 mm ( NPS 2" to 24" ) Between Class 150 (PN20) flanges 29 C + 210 C Max Pressure : 20 Bars Specifications : Double eccentric
AIL METSEAL Butterfly Valves
AIL METSEAL Butterfly s The AIL METSEAL Butterfly is a high performance valve which is used for positive isolation in Power Generation, Petroleum Refining, Oil and Gas Production, Chemical, Petrochemical
Triple Offset Valves
Triple Offset Valves Value Statement For the harsh conditions of critical process applications, steam isolation, high cycle frequency, and temperature extremes, the Flowseal MS triple-offset metal-seated
Oil safety valve 141 Flame arrester 143 Air release valve for reservoirs 145 Reparation of valves, pumps and other valves 148
PRODUCT CATALOGUE 2 History 4 Products Gate valves Flat 13 Oval 25 Round 41 Knife 53 Butterfly valves Double eccentric 63 Triple eccentric 81 Turbine inlet valves 85 Non-return valve Swing check valves
TECHNICAL BULLETIN. Valtek ShearStream SB Control Valves. Segmented V-port Ball Valves. Experience In Motion VLEETB
TECHNICAL BULLETIN Valtek ShearStream SB Control Valves Segmented V-port Ball Valves VLEETB4152-03 11.02 Experience In Motion Primary characteristics ShearStream SB is a ball sector valve with metal-to-metal
Innovative World Leader
Innovative World Leader The ANSWER to Tight shut-off in various applications, Series 600 Triple offset butterfly valve is a virtual solution for heavy duty process, high pressure & temperature, and high
NELES SOFT SEATED BALL VALVES, SEAT SUPPORTED, FULL AND REDUCED BORE, SERIES X
NELES SOFT SEATED BALL VALVES, SEAT SUPPORTED, FULL AND REDUCED BORE, SERIES X Metso's Neles series X is a seat supported modular ball valve. Neles X series valves incorporate robust stem to ball connection.
ACE VALVE COMPANY LIMITED
ACE VALVE COMPANY LIMITED Http://www.acevalve.co.kr 2013.04. ACE VALVE CATALOG 278-4 Mangdeokri, Juchonmyun, Gimhae, Gyeongnam, Korea. TEL +82--310-0 FAX +82--329-06~8 E-mail acevalve@acevalve.co.kr Homepage
NELES HIGH CAPACITY TRIPLE ECCENTRIC DISC VALVE, METAL SEATED NELDISC SERIES L6
NELES HIGH CAPACITY TRIPLE ECCENTRIC DISC ALE, METAL SEATED NELDISC SERIES L6 Metso's Neles series L6 is a double flanged metal seated Neldisc triple eccentric disc valve with one piece body design, for
arflu globe valves The quality you can trust Globe valves Because of their configuration,
The quality you can trust globe valves 2 18 Globe valves Because of their configuration, globe valves are perfect to regulate or limit the fluid port. epending on the needs of the system, design or open
GWC Italia. Proven technology for individual valve solutions worldwide FSV-1005
GWC Italia Proven technology for individual valve solutions worldwide forged STEEL VALVES GATE, GLOBE & CHECK FSV-1005 2 GWC ITALIA Proven technology for individual valve solutions worldwide w w w. g w
The bolted bonnet configuration achieves simultaneously the best performance and the highest safety.
The achieves simultaneously the best performance and the highest safety. Features A rugged body and bonnet design in accordance with API 600, ASME B16.34 and BS 1414. Tight shutoff performance is always
HOPPER SHAPE KNIFE GATE VALVE
HOPPER SHAPE KNIFE GATE VALVE The model knife gate is a uni-directional wafer valve designed for industrial bulk handling service applications (powdered and granular products). The special design of the
Series 240 Type and Type Pneumatic Control Valves Type 3244 Three-way Valve
Series 240 Type 3244-1 and Type 3244-7 Pneumatic Control Valves Type 3244 Three-way Valve DIN and ANSI versions Application Mixing or diverting valve for process engineering and industrial applications
WAFER STYLE KNIFE GATE VALVE
11 WAFER STYLE KNIFE GATE VALVE The model knife gate is an uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging shut off
NAF-Setball ball sector valves DN , PN 10-40, ANSI Class
NAF-Setball ball sector valves DN 25-400, PN 10-40, ANSI Class 150-300 Fk 41.51(12)GB 4.98 Replaces Fk 41.51(1GB 12.97 Primary characteristics NAF-Setball is a ball sector valve with metal-to-metal or
BALL SECTOR VALVE of stainless steel 455 (459) series
Operation C ont R o L Description Edition Högfors ball sector valve series 55 is specially designed for control applications of various media like liquids, pulps and steam. 55KC is used for sticky and
Pneumatic Butterfly Valve Pfeiffer Type BR 14b/AT
Pneumatic Butterfly Valve Pfeiffer Type BR 14b/AT Application Tight closing, double eccentric butterfly valve for process engineering and plants with industrial requirements Nominal size DN 80 to DN 400
Wafer, Lug and Double Flanged Type
Document : PG0 :1 Product Group 0 Wafer, Lug and Double Flanged Type Page 1 www.globalvalvecenter.com 2011 : PG0 Product Group 0 Description Product Group 0 Butterfly Valves Triple eccentric metal seated
Zwick Series Tri-Con. Zero-Leakage Metal-Seated Valves
Zwick Series Tri-Con Zero-Leakage Metal-Seated Valves Features Unique triple-offset, conical seating Metal-to-metal seating Unique, self-centering disc design Emission-control technology Superior bearing/bushing
BALL VALVE DOUBLE BLOCK & BLEED design RSD BB type TRUNNION MOUNTED, ANTISTATIC,FIRE SAFE DESIGN API607,API6FA
BALL VALVE DOUBLE BLOCK & BLEED design RSD BB type TRUNNION MOUNTED, ANTISTATIC,FIRE SAFE DESIGN API607,API6FA APPLICATIONS Designed and executed for use in pipeline systems, which convey fluids under
FLANGED FULL BORE BALL VALVE, SERIES MBV, ANSI CLASS 600 VERSION
FLANGED FULL BORE BALL VALVE, SERIES MBV, ANSI CLASS 6 VERSION 1 MBV 27 Issue 12/98 Applications Chemical and petrochemical plants. Oil and gas production. Hydrocarbons. Liquids. Water. Power plants. Suitable
BUTTERFLY VALVE 17 SERIES Gearbox
DN H1 H2 H3 BUTTERFLY VALVE 17 SERIES Gearbox FIGURE: 17234ER: 17234BR: 17234VR: Seat in EPDM, with gearbox Seat in Buna, with gearbox Seat in Viton, with gearbox B ØR L DIMENSIONS: (mm) DN L B XR H1 H2
Butterfly valve for marine cargo systems Edition:
Datasheet Butterfly valve for marine cargo systems Edition: 2013-05 Type MTV Type MTVL Wafer design Lugged design Nominal pressure PN 10-25 Class 150 Nominal size DN 80-400 Material Stainless steel Advanced
Features BALL VALVES. Split Wafer. Carbon steel wafer PN ANSI 600 STANDARD FEATURES FEATURES ON REQUEST
OMAL S.p.a. Via Ponte Nuovo, 11-25050 Rodengo Saiano (BS) ITALY Phone +39 0308900145 - Fax +39 0308900423 Booked in the Enterprise Register of: Brescia number 1661640175 Share capital completely deposited:
Data Sheet Rotary Plug Valve Type 82.7
Data Sheet Rotary Plug Valve Type 82.7 Double eccentric control valve for process engineering and industrial applications Valve Size DN 25 to 25 NPS 1 to 1 Nominal Pressure PN 1 to PN 4 CL 15 and 3 Temperature
NELES SOFT SEATED BUTTERFLY VALVE SERIES MAPAG BA FOR PSA PLANT ON/OFF AND CONTROL SERVICE
NELES SOFT SEATED BUTTERFLY VALVE SERIES MAPAG BA FOR PSA PLANT ON/OFF AND CONTROL SERVICE Series Mapag BA is a wafer type butterfly valve with a one piece body and soft seat.. It is specially designed
BR 26d Ball valve. Stainless Steel. Application: Versions: Special versions:
Application: Stainless Steel BR 26d Ball valve Tight-closing Ball valve made of stainless steel for corrosive media, especially to meet high process requirements in chemical plants: Nominal sizes DN 15
Materials : Carbon steel or stainless steel
Size : Ends : Min Temperature : Max Temperature : DN 50 to 600 mm Between PN25 or PN16 flanges 29 C + 210 C Max Pressure : 25 Bars Specifications : Double eccentric Wafer type Fire safe according to ISO
Technical changes kept in reserve WAFER STYLE KNIFE GATE VALVE. DN 50 to DN 250: 10 kg/cm² DN 300 to DN 400: 6 kg/cm²
WAFER STYLE KNIFE GATE VALVE The A model knife gate is an uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging shut off
SECTION S DOUBLE OFFSET HIGH PERFORMANCE BUTTERFLY VALVES
SECTION S DOUBLE OFFSET HIGH PERFORMANCE BUTTERFLY VALVES DESCRIPTION STANDARD COMPLIANCE/CERTIFICATIONS S-2 ADVANTAGES S-3 PAGE SOFT SEAT EXPLODED VIEW S-4 FIRE SAFE SEAT EXPLODED VIEW S-5 METAL SEAT
CONTROL VALVE TYPE BR33
CONTROL VALVE TYPE BR33 version 02/2012 www.polnacorp.eu BR 33 - ROTARY CONTROL GLOBE VALVE WITH ECCENTRICALY SET ROTARY PLUG Nominal dimensions DN 25 - DN 300 1-12 Nominal pressure PN 10-40 Class 150,