markilux 1300 Basic The awning which sets exacting standards PATIO AND BALCONY AWNINGS safe timeless beautiful

Transcription

1 PTIO ND BLCONY WNINGS safe timeless beautiful markilux 1300 Basic The awning which sets exacting standards rated to wind resistance class 2 (corresponds to Beaufort 5) markilux

2 markilux 1300 Basic PTIO ND BLCONY WNINGS side view with awning retracted, top fixture markilux pitch adjustment gear optionally at a surcharge side view with awning retracted, top fixture folding arm with round steel-link chain markilux shadeplus / drop valance optionally at a surcharge markilux aluminium coverboard optionally at a surcharge side view at a pitch of 55 shadeplus / drop valance (optional) Frame colours Design Features, Technical Specification and Optional ccessories traffic white RL 9016 standard optional the robust folding arms with single steel-link chain ensure a taut cover metallic aluminium RL 9006 non-standard powder-coated finish the pivot bolts are made from corrosion-proof stainless steel and run in Teflon-coated bushes the strong 40 mm 40 mm torque bar is extremely resistant to twist and deflection, the roller tube is made of steel and has a diameter of 85 mm for the same reason iscellaneous standard optional the attractive front profile made with integrated gutter ensures water drains away to the sides the pitch adjustment gear mechanism (available optionally at a surcharge) that affords added protection: the sun marches across the sky your awning marches with it; with the pitch adjustment gear mechanism you can change the (normally fixed) pitch from 4 to 54 or 35 to 85 by simply using a winding handle pitch adjustment gear shadeplus / drop valance coverboard light and wind sensor insertable side blind valance infrared heater vibrabox / radio control light sensor Sunis WireFree valance shape 1, 2 or 6 (please refer to the section world of colours in the markilux collection ) Colours similar to those in the RL chart. Colours may differ slightly from those depicted in both hue and finish. 256 Special Features / Frame colours / iscellaneous

3 markilux 1300 Basic PTIO ND BLCONY WNINGS Dimensions and configuration options 01 min ) ) ) ) 250 3) 300 3) 350 3) 400 2) 3) dimensions in cm a shadeplus / drop valance is not possible 2) awnings with 3 arms or a projection of 400 cm are only available with motor 3) please note the minimum widths! 11 Dimensions and tolerances Operation / Drive standard manual operation optional width projection + 20 / mm ± 40 mm servo-assisted operation hard-wired motor io radio controls radio-controlled motor (433 z) housing tolerances awning cover width awning width 0 mm 170 mm awning cover length awning projection Covers Coupled units fabric range no. sunsilk snc sunsilk perla FR sunvas snc sunvas perla mm standard / / / optional standard 2 fields junction roller one-piece cover optional 4) 5) 4) for minimum widths please consult the section Technical Information 5) see overview Bracket fixture range motor 2 1 no. of folding arms manual operation 2 no. of bespoke arms awning width min. minimum widths projection no. of rolltex bearings Dimensions and configuration options 257

4 markilux 1300 Basic PTIO ND BLCONY WNINGS dditional information The width of the awning cover is always less than that of the awning. Please refer cover sizes in the case of coupled units and those with more than 2 arms to us. tolerances the actual drop may be shorter than the nominal drop by up to 5 cm. For the maximum shadeplus drops please consult the section Technical Information. Pitch adjustment range: from 5 to 55 (to the horizontal). Pitch adjustment range in the case of pitch adjustment gear: either from 4 to 54 or from 35 to 85 ( in both cases to the horizontal). Definition of projection: Please consult the section Technical Information. In the case of manual operation approximately 16 winding handle revolutions can be assumed per metre of awning projection. It takes approximately 12 seconds per metre to extend a motor-driven awning. Definition of shadeplus drop: The shadeplus drop is measured from the bottom edge of the shadeplus profile to the bottom edge of the valance profile. Due to fabric thickness shadeplus is not available with sunsilk perla FR, sunvas perla or PVC covers. Coupled folding-arm awnings are available up to a max. of 2 single units side by side, however only with a motor drive. 3 units coupled together on request. coupled unit is available with junction roller. Pattern repeat mismatches are possible in the case of junction roller covers. junction roller may not fit when the projection is the maximum for the width of each awning. (see also the section on Installation, the arm separation table). If coupled blinds are fitted into a recess or reveal the overall width of the coupled awning must be at least 6 cm less than the width of the opening to allow the awning to be coupled. Fixtures, fittings and accessories 0 face fixture bracket assembly 60 face fixture bracket assembly 90 top fixture bracket assembly 0 mm 60 mm 90 mm top fixture bracket assembly 60 mm 0 eaves fixture bracket 0 mm 270 eaves fixture bracket assembly 270 mm insert RL colour code no 258 dditional information / Fixtures, fittings and accessories

5 PTIO ND BLCONY WNINGS markilux 1300 Basic Fixtures, fittings and accessories 01 spreader plate mm spreader plate B mm Flat plate and angled bracket for eaves fixture machine finish spreader / backing plate assembly eaves fixture mm spacer plate for face fixture mm N.B! max. stacking height 200 mm spacer plate for face fixture mm spacer plate for face fixture mm N.B! max. stacking height 200 mm spacer plate for top fixture mm spacer plate for face fixture mm spacer plate for top fixture mm N.B! max. stacking height 200 mm spacer plate for top fixture mm N.B! max. stacking height 200 mm spacer plate for top fixture mm stand-off bracket for face fixture bracket cover plate for installation with spacer plates and stand-off brackets in the case of external insulation mm stand-off bracket for 2 pcs. face fixture bracket reducing bolt assembly / SW mm in length cover plate for installation with spacer plates and stand-off brackets in the case of external insulation mm reducing bolt assembly 16 / SW mm in length reducing bolt assembly 12 / SW mm in length reducing bolt assembly / SW mm in length angled profile for eaves fixture 0 0 mm available by the metre, not pre-drilled machine finish please refer to the section Technical Information. insert RL colour code no Fixtures, fittings and accessories 259

6 markilux 1300 Basic PTIO ND BLCONY WNINGS Face fixture Pull-out force [NNewton] per upper fixing point according to EN 13561, wind resistance class 2 Compression-proof substrate Non compression-proof substrate [cm] FB [N] FB [N] mm 3 0 mm 2 60 mm 2 60 mm 2 60 mm 2 60 mm B The pull-out force refers to the vertical centre to centre measurement between the fixture points of 90 mm. If this measurement is reduced to the minimum, the pull-out force increases by % in the case of compression-proof substrates and by 19% in the case of non compression-proof substrates. If the awning is fixed with 2 brackets per folding arm, the pull-out force can be halved. Place the brackets immediately to the left and right of the arm bearer. FB B SD awning width projection pull-out force per fixing point bracket quantity width no. of fixing points coverboard face fixture bracket assembly 60 mm face fixture bracket assembly 0 mm 240 SD , , Face fixture

7 PTIO ND BLCONY WNINGS markilux 1300 Basic Face fixture with spreader plate Pull-out force [NNewton] per upper fixing point according to EN 13561, wind resistance class 2 The pull-out force refers to the vertical centre to centre measurement between the fixture points of 76 mm. In the case of spreader plates a washer conforming to DIN 9021 must be used. FB BP B SD Compression-proof substrate awning width projection pull-out force per fixing point bracket quantity width no. of spacer plates no. of fixing points coverboard Non compression-proof substrate [cm] FB [N] FB [N] mm 3 0 mm 2 60 mm 2 60 mm 2 60 mm 2 60 mm BP DP B Face fixture with spreader plate 261

8 markilux 1300 Basic PTIO ND BLCONY WNINGS Face fixture with spreader plate B Pull-out force [NNewton] per upper fixing point according to EN 13561, wind resistance class 2 Compression-proof substrate Non compression-proof substrate [cm] FB [N] FB [N] mm 3 0 mm 2 60 mm 2 60 mm 2 60 mm 2 60 mm BP DP B The pull-out force refers to the vertical centre to centre measurement between the fixture points of 350 mm. In the case of spreader plates a washer conforming to DIN 9021 must be used. FB BP DP B awning width projection pull-out force per fixing point bracket quantity width no. of spreader plates no. of spacer plates no. of fixing points 262 Face fixture with spreader plate B

9 PTIO ND BLCONY WNINGS markilux 1300 Basic Face fixture with stand-off brackets Pull-out force [NNewton] per upper fixing point according to EN 13561, wind resistance class 2 The pull-out force refers to the vertical centre to centre measurement between the fixture points of 120 mm. In the case of stand-off brackets washers conforming to DIN 9021 must be used. FB B D awning width projection pull-out force per fixing point bracket quantity width no. of fixing points no. of stand-off brackets stand-off bracket for face fixture bracket stand-off bracket for 2 pcs. face fixture bracket Compression-proof substrate Non compression-proof substrate [cm] FB [N] FB [N] mm 3 0 mm 2 60 mm 2 60 mm 2 60 mm 2 60 mm D D B min. 80 max ,50 Face fixture with stand-off brackets 263

10 markilux 1300 Basic PTIO ND BLCONY WNINGS Face fixture with shadeplus Pull-out force [NNewton] per upper fixing point according to EN 13561, wind resistance class 2 Compression-proof substrate Non compression-proof substrate [cm] FB [N] FB [N] mm 3 0 mm 2 60 mm 2 60 mm 2 60 mm 2 60 mm B The pull-out force refers to the vertical centre to centre measurement between the fixture points of 90 mm. If this measurement is reduced to the minimum, the pull-out force increases by % in the case of compression-proof substrates and by 19% in the case of non compression-proof substrates. If the awning is fixed with 2 brackets per folding arm, the pull-out force can be halved. Place the brackets immediately to the left and right of the arm bearer. FB B SD awning width projection pull-out force per fixing point bracket quantity width no. of fixing points coverboard face fixture bracket assembly 60 mm wall bracket 0 mm 280 SD , , Face fixture with shadeplus

11 PTIO ND BLCONY WNINGS markilux 1300 Basic Face fixture with shadeplus and spreader plate Pull-out force [NNewton] per upper fixing point according to EN 13561, wind resistance class 2 The pull-out force refers to the vertical centre to centre measurement between the fixture points of 76 mm. In the case of spreader plates a washer conforming to DIN 9021 must be used. FB BP DP B SD Compression-proof substrate awning width projection pull-out force per fixing point bracket quantity width no. of spreader plates no. of spacer plates no. of fixing points coverboard Non compression-proof substrate [cm] FB [N] FB [N] mm 3 0 mm 2 60 mm 2 60 mm 2 60 mm 2 60 mm BP DP B Face fixture with shadeplus and spreader plate 265

12 markilux 1300 Basic PTIO ND BLCONY WNINGS Face fixture with shadeplus and spreader plate B Pull-out force [NNewton] per upper fixing point according to EN 13561, wind resistance class 2 Compression-proof substrate Non compression-proof substrate [cm] FB [N] FB [N] mm 3 0 mm 2 60 mm 2 60 mm 2 60 mm 2 60 mm BP DP B The pull-out force refers to the vertical centre to centre measurement between the fixture points of 350 mm. In the case of spreader plates a washer conforming to DIN 9021 must be used. FB BP DP B awning width projection pull-out force per fixing point bracket quantity width no. of spreader plates no. of spacer plates no. of fixing points 266 Face fixture with shadeplus and spreader plate B

13 PTIO ND BLCONY WNINGS markilux 1300 Basic Face fixture for shadeplus / drop valance with stand-off brackets Pull-out force [NNewton] per upper fixing point according to EN 13561, wind resistance class 2 The pull-out force refers to the vertical centre to centre measurement between the fixture points of 120 mm. In the case of stand-off brackets washers conforming to DIN 9021 must be used. FB B DP awning width projection pull-out force per fixing point bracket quantity width no. of fixing points no. of stand-off brackets stand-off bracket for face fixture bracket stand-off bracket for 2 pcs. face fixture bracket Compression-proof substrate min. 80 max. 300 Non compression-proof substrate [cm] FB [N] FB [N] mm 3 0 mm 2 60 mm 2 60 mm 2 60 mm 2 60 mm D D B Ø (62,50) Ø Face fixture for shadeplus / drop valance with stand-off brackets 267

14 markilux 1300 Basic PTIO ND BLCONY WNINGS Top fixture Pull-out force [NNewton] per upper fixing point according to EN 13561, wind resistance class 2 Compression-proof substrate Non compression-proof substrate [cm] FB [N] FB [N] mm 2 90 mm 3 90 mm 2 90 mm 3 90 mm 2 90 mm 2 60 mm 2 60 mm 2 60 mm 2 60 mm B The pull-out force refers to the horizontal centre to centre measurement between the fixture points of 80 mm. If the awning is fixed with 2 brackets per folding arm, the pull-out force can be halved. Place the brackets immediately to the left and right of the arm bearer. FB awning width projection pull-out force per fixing point bracket quantity width B no. of fixing points top fixture bracket assembly 90 mm top fixture bracket assembly 60 mm , , Top fixture

15 PTIO ND BLCONY WNINGS markilux 1300 Basic Top fixture with shadeplus / drop valance Pull-out force [NNewton] per upper fixing point according to EN 13561, wind resistance class 2 The pull-out force refers to the horizontal centre to centre measurement between the fixture points of 80 mm. If the awning is fixed with 2 brackets per folding arm, the pull-out force can be halved. Place the brackets immediately to the left and right of the arm bearer. FB Compression-proof substrate awning width projection pull-out force per fixing point bracket quantity width 55 17,5 17, B Non compression-proof substrate [cm] FB [N] FB [N] mm 2 90 mm 3 90 mm 2 90 mm 3 90 mm 2 90 mm 2 60 mm 2 60 mm 2 60 mm 2 60 mm B no. of fixing points top fixture bracket assembly 90 mm top fixture bracket assembly 60 mm Top fixture with shadeplus / drop valance 269

16 markilux 1300 Basic PTIO ND BLCONY WNINGS Eaves fixture torque value for the bracket in the immediate vicinity of the arm Pull-out force [NNewton] per upper fixing point according to EN 13561, wind resistance class 2 Torque Shear force [cm] d [Nm] FS [N] T B The shear force is calculated on the basis of 2 fixing points per bracket, because depending on the roof pitch it cannot be guaranteed that 4 fixing points per bracket can used. d T FS B awning width projection torque value for the bracket in the immediate vicinity of the arm no. of brackets shear force no. of fixing points 270 Eaves fixture

17 PTIO ND BLCONY WNINGS markilux 1300 Basic Eaves fixture with additional spreader / backing plate torque value for the bracket in the immediate vicinity of the arm Pull-out force [NNewton] per upper fixing point according to EN 13561, wind resistance class 2 By using the additional flat fixture plate, the shear force is reduced in comparison with conventional eaves fixture. d T FS B Torque awning width projection torque value for the bracket in the immediate vicinity of the arm no. of brackets shear force no. of fixing points Shear force [cm] d [Nm] FS [N] T B Eaves fixture with additional spreader / backing plate 271

18 markilux 1300 Basic PTIO ND BLCONY WNINGS Face fixture with manual operation , , Face fixture with manual operation

19 PTIO ND BLCONY WNINGS markilux 1300 Basic Pitch adjustment gear Ideal for additional solar protection on the balcony Up to a projection of 300 cm and with the awning extended, 2 folding arms can be raised or lowered easily and noiselessly between the angles of 4 and 54 or 35 and 85 by means of a winding handle (only gearbox operated). The eye used to alter the pitch of the awning is attached directly to the gearbox, which can be positioned optionally on the left or the right. ll the components needed to adjust the pitch of the awning are hidden away inside the torque bar and so protected from the elements. fine tuning mechanism enables the arms to be levelled with ease. The pitch adjustment gear is supplied in white with white awnings and in black with any other colour. ttention! The pitch adjustment gear may only be operated when the awning is extended. ttempting to adjust the pitch with the awning closed, may cause the system to malfunction! min SD coverboard standard folding arms standard min. minimum widths projection Pitch adjustment gear 273

20 markilux 1300 Basic PTIO ND BLCONY WNINGS Bracket fixture range for awnings with 2 folding arms SU SU B dimensions in cm SB ZB [cm] [cm] * * * * * dimensions in cm BT T T W 60 mm 2 0 mm 2 2 DE 60 mm 2 90 mm 2 2 D 90 mm 2 4 If the brackets cannot be positioned in accordance with this table, make sure the actual measurements are noted on the order form! * T BT B W DE D SB ZB SU Please note the minimum widths! Dimension is only valid for standard arms! Dimension is 13 cm less in the case of bespoke arms. In the case of small awnings the brackets can only be fitted inside the arms, i.e. the position denoted by measurement. awning width projection arm position no. of brackets bracket width bracket fixture range face fixture top fixture eaves fixture standard width intermediate width coverboard overhang 2 cm 274 Bracket fixture range for awnings with 2 folding arms

21 PTIO ND BLCONY WNINGS markilux 1300 Basic SU Bracket fixture range for awnings with 3 folding arms B SU LR B 05 W dimensions in cm SB ZB [cm] [cm] B [cm] [cm] B [cm] [cm] B [cm] [cm] B [cm] [cm] B [cm] K * 204* dimensions in cm BT T 60 mm 2 0 mm DE 60 mm 2 90 mm 3 dimensions in cm D 90 mm 5 If the brackets cannot be positioned in accordance with this table, make sure the actual measurements are noted on the order form! * The 2 60 mm brackets cannot be fitted in this instance and are not supplied awning width projection arm position B arm position T no. of brackets BT bracket width B bracket fixture range W face fixture DE top fixture D eaves fixture SB standard width ZB intermediate width LR a rolltex bearing with accompanying bracket is always placed under a central seam (depends on the awning size) SU coverboard overhang 2 cm K minimum awning width Bracket fixture range for awnings with 3 folding arms 275

22 markilux 1300 Basic PTIO ND BLCONY WNINGS 276