1. OVERVIEW DRAWING 2

Transcription

1 1

2 1. OVERVIEW DRAWING 2

3 2. IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the followings: Read all instructions before using the treadmill. DANGER To reduce the risk of electric shock: Always unplug this appliance from the electrical outlet immediately after using and before cleaning. WARNING To reduce the risk of burns, fire, electric shock, or injury to persons: 1. The product should never be left unattended while plugged in. Unplug the product from the outlet when not in use. 2. Close supervision is necessary when this product is used by or near children, invalids, or disabled persons. 3. Be sure to use the product only for its intended use as described in this manual. Do not use any attachment not recommended by the manufacturer in order to avoid any danger or accidents. 4. Never operate the product if it has a damaged cord or plug, if it is not working properly, if it has been damaged, or dropped into water. Please return the product to the service center of seller for examination and repair. 5. Do not carry this product by the supply cord or use the cord as a handle. 6. Keep the cord away from hot surfaces or ground. 7. Never operate the product with the air vents blocked. Keep the air vents free of lint, hair, etc. 8. Never drop or insert any objects into any openings. 9. Do not use or operate outdoors. 10. Do not operate where aerosol (spray) products are being used or where oxygen is thin. 11. Before turning the product power off, turn all controls to the off status then remove the plug from the outlet. 12. Connect the product to a properly grounded outlet only. 13. If the treadmill is foldable, when user finishes using the treadmill, the elevation needs to be back to original position. 14. When user is using the treadmill, it can not be folded at the same time. 15. This machine is only intended for household use. Note For the treadmill with folding function, be sure that the elevation is 0 before folding(to avoid interference of the components). 3

4 3. GROUNDING INSTRUCTIONS The products must be grounded first. If malfunction or breakdown occurs, grounding will provide a path of least resistance for electric current to reduce the risk of electric shock. The product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Danger Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the products are properly grounded. Do not modify the plug provided with the product if it will not fit the outlet, have a proper outlet install by a qualified electrician. The product is for use on nominal 220~240 volt and has a grounding plug that looks like the plug illustrated in the figure. Make sure that the product is connected to an outlet having the same configuration as the plug. There is no need to use any adapter for this product. Figure Grounding methods GROUNDED OUTLET GROUNDED GROU PIN 4

5 4. MOTORIZED TREADMILL PRE-ASSEMBLY Handrail control button and heart rate strap are optional items in the package 1. Heart rate can be measured in this treadmill. Attach strap to chest during exercise, the heart rate value will display on the PULSE window. 2. Except using the control button on the console, the control button on the handrail can also be used to adjust speed and elevation. The control button on the left handrail is for elevation while the right handrail button is for speed adjustment. ITEM Description Qty A Computer Console 1 B Frame 1 C Upright (L) 1 D Upright (R) 1 E Decoration Cover (L) 1 F Decoration Cover (R) 1 G Upper Handrail Cover (L) 1 H Upper Handrail Cover (R) 1 I Lower Handrail Cover (L) 1 J Lower Handrail Cover (R) 1 ITEM Description Qty a Screw M5xP0.8x10 4 b Allen Bolt M8xP1.25x15 10 c Allen Bolt M8xP1.25x15 4 d Allen Bolt M8xP1.25x60 4 e Screw ψ4x16 6 f Allen Wrench + Screwdriver 5mmx70mmx70mm 1 g Allen Wrench 6mm 1 h Power Cord 1 i Safety Key/Clip 1 j Lubricant 1 k Mp3 Sound Cable 1 5

6 6

7 5. ASSEMBLY STEPS 1. After pull out Control Wire with Guide Thread in right Upright (D), put left and right Uprights (C, D) to the suitable place and then fix with Allen Bolt (b). Ps. To avoid unexpected accident, always assemble the treadmill with an assistant, do not assemble by oneself. Ps. When assemble the Uprights, one person should hold the Upright to prevent it from falling. 2. After left and right Uprights are tightened, cap left and right Decoration Covers (E, F) to the Frame and tighten them with Screw (a). 7

8 3. Turn Handlebar Assembly upwards and connect with the Computer. Tighten with Allen Bolt (c). 4. Put Computer Console (A) on the treadmill and connect all control wires. Then thread them into the tube of the left and right Handrails. Assemble Computer Console to the Handrails and fix with Screw (d). Ps. When fix the screws, pay attention that do not damage control wires in the tube. 8

9 5. After finish above steps, cap left and right Upper Handrail Covers (G, H) and Lower Handrail Covers (I, J) to the Uprights. Fix with Self Tapping Screw (e). Ps. When fix the screws, pay attention that do not damage control wires in the tube. Ps. Pay attention when assemble the Handrail Covers, after Upper Handrail Cover hooks the Upper Computer Cover, then assemble it to the Lower Handrail Cover. 9

10 6. CAUTION Note: Made of high pressure, the cylinder must be taken care to avoid danger caused by the impact with other objective. Note: If the cylinder is hit, it may cause damage and make the use not smooth. When the user is folding the treadmill, it may result in the falling of the frame and cause injury. This treadmill is foldable. All operation should be stopped when folding (include stopping walking belt, disconnecting power cord), then fold up treadmill as shown on the drawing. Please make sure the pedal stopper is exactly in the slot of preventing the frame from sliding down. Vice Versa, to unfold the treadmill, step on the pedal stopper with the direction shown on the drawing, then carefully unfold the treadmill frame on to the ground. Do not release the frame before it touches the ground. (Ps. 1. To prevent from any injury when moving a folded treadmill, hold on to the adjustment box with two hands. Then pivot the treadmill towards you until the wheels of the treadmill are rolling freely.) (Ps. 2. Make sure the floor is cleared and flat when moving the folded treadmill around.) 10

11 7. MAINTENANCE 1. Walking Belt Centering. If the Walking Belt tracks off center to the right or left of the deck, first turn the power off. Then use 6mm Allen wrench to tighten the rear roller bolt on the side of the treadmill toward which the belt is moving. For example, if the belt moves to the left and the deck becomes exposed on the right, tighten the bolt on the left side of the frame. Tighten about 1/4 of turn (clockwise). If the belt does not move back to the center of the treadmill, make another adjustment to the same bolt. Once the Walking Belt has been adjusted closer to the center, the treadmill can be started again. Ps.1: The above mentioned is pretty import, make sure to follow the procedure. Ps.2: Make sure the walking belt going on right without any tracks off the centers it depends on the position and weight. 2. It is recommended that the deck be lubricated every 6-12 months according to the frequency of usage. First, use 6mm Allen wrench to loosen the bolts in the end caps. Pull up the Walking Belt, dispense the lubricant on the deck, and spread evenly. After lubricating the deck, center the belt, and check the belt tension. Adjust the belt as mentioned in step 3. (Ps. If the belt happens to slip, follow the above steps and lubricate the running deck.) SUGGESTED PREVENTIVE MAINTENANCE SCHEDULE IN ACCORDANCE WITH THE AVERAGE RUNNING SPEED Measurement Speed Interval 6KM/hr below 1 year Metric 6~12KM/hr 6 months 12KM/hr above 3 months 4mile/hr below 1 year English 4~8mile/hr 6 months 8mile/hr above 3 months Note: This preventive maintenance schedule is only meant for home use. It is suggested to maintain the unit every month for commercial use. 11

12 8. Computer Instruction I. Start Display: MP3 jack is optional, not all machines have this function 1. If the SAFETY KEY is taken off, the matrix screen will display the arrow downwards. If the SAFETY KEY is replaced, the matrix screen will display KGS (mile) for avoirdupois unit. Weight window will blink and the preset value is 70KG (150LBS). Range is 23~130KG (50~286LBS). At this time, the light Weight indicates will be light. Whether finish set or not set, press ENTER. This window will come back to start/ready status and the matrix window displays pulsatile heart-shaped picture. The aim of setting weight is to make a change of burning CALORIES. This can be only done after starting. It does not need to set in PROGRAM. It means you can use the value after starting. You must set newly after starting again. 2. When the SAFETY KEY is removed, the treadmill will stop running. At this time place the SAFETY KEY back, the beeper will sound and then all the values will go back to the initial position. 3. Under usual start/ready status, if you don t hold pulse sensor, PULSE window will display HP. When you hold the pulse sensor, you will see PULSE window displays pulse value. 12

13 II. Operation Mode: 1. Under start/ready status, press Mode to enter edit mode. 2. Under start/ready status, press Start to enter directly by Manu run. 3. When the SAFETY KEY is taken off and then replaced, it will not make reposition action any where it is. You need to press start key to perform the incline to reposite it. 4. When power on, it will not make reposition action any where it is. You need to press start key to perform the incline to reposite it. 5. Under start/ready status, continuously press stop key for 5 seconds, it will make reposition action any where it is. During perform any program, if press stop key, the program will stop. If users want to continuously perform the program, press start key or again press stop key to leave the program and back to start/ready status. III. Edit Mode: 1. Under Start/Ready position, press Mode to choose Manual and Program mode by press +/- key. 2. Program mode:press +, - keys to edit Program(P1~P8). The light PROGRAM indicates blinks. LCD can display P1~P8 for users to edit. Press +, - to edit. Press ENTER to enter TIME edit. The preset value is 30min,range is 20~99 min,step is 1 min. After edit, press ENTER or START to start the machine. If you press START directly during edit, the rest un-edited functions are pre-set. During edit, INCLINE and SPEED window will display first level value. The matrix window will display this picture. 3. WARM UP and COOL DOWN function: During WARM UP or Program position, change speed or inclination, the value will increase or decrease in the next level. COOL DOWN is not affected and STOP is the only function which can be carried out. 4. PROGRAM has 30 levels in all. The three anterior are WARM UP, the three later are COOL DOWN. Everyone is 3 minutes. The setting time except anterior and later which mean 6 minutes will be execute averagely by surplus 24 levels HOLES mode have not functions of WARM UP or COOL DOWN. When distance is equal to 3.5KM, the motor will stop, the INCLINE is 0 and displays End. IV. Program Operation and Instruction: Manu mode 1. When press Start, it will begin to count down for 3 seconds, after that, the motor will start, the speed will start at 0.8KPH(0.5MPH). The matrix window goes contrarotate like along playground, every circle is 0.4KM (0.25MIL). 2. Speed STEP is 0.1, you can press +, - keys to select(the speed UP/DOWN step is 0.1), or press speed instant key to select. 3. Incline STEP is 1, you can press +, - keys to select(incline UP/DOWN step is 1), or press incline instant key to select. 4. TIME set or not set: 13

14 (1) When TIME has bee set, the window will display a time value counting down from the target value, when the time reaches 0:00, the treadmill will stop automatically. (2) When TIME hasn t been set, the window will display the exercise time, when the time reaches 99:00, the treadmill will stop automatically. 5. When you press Mode key, it will switch among SPEED, DISTANCE and CALORIES while INCLINE, PULSE or WEIGHT not, only displaying INCLINE. If there is PULSE, it will mainly display Pulse. If there is pulse value, the pulse window will display pulse value. 6. Press Stop when the motor is working, the motor will stop and the incline motor will stop, the window will display Stop; If you press START key again, the motor will start after 3-seconds countdown, the speed will be keep at the same before stop, and the incline will be increased to the set height before stop. 7. During Stop, press Stop and hold it for 3 seconds, it will switch to start/ready status. 8. Under End status, if it last 30 seconds(or press Stop key), it will switch to start/ready status. 9. The time pre-set value is 0, range 20~99,when the time is edited at 20 minutes, you can press +- key to increase or decrease, the increase step is 1, if decrease, it will go back to 0 directly. During exercise, the matrix window goes contrarotate like along playground. V. Program Mode P1 Manu time:pre-set 0min;range 20~99min,step 1 min. P2 9 hole LEVEL:pre-set 1,range 1~10, step1,3500 meter is based on distance. P3 hill climb LEVEL:pre-set 1,range 1~10,step 1. time:pre-set 30min;range 20~99min,step 1 min. P4 hill run LEVEL:pre-set 1,range 1~10,step 1. time:pre-set 30min,range 20~99min,step 1 min. P5 interval LEVEL:pre-set 1,range 1~10,step 1. time:pre-set 30min,range 20~99min,step 1 min. P6 rolling LEVEL:pre-set 1,range 1~10,step1. time:pre-set 30min,range 20~99min,step 1 min. P7 Weight loss LEVEL:pre-set 1,range 1~10,step 1. time:pre-set 30min,range 20~99min,step 1 min. P8 Custom time:pre-set 30min,range 20~99min,step 1 min. PROGRAM has 30 levels in all (SE01~SE30) and the pre-set values all are lowest values. Setting:time,program execute value and setting time can execute in 30 level averagely. (1)After enter program control function, the light that delegates LEVEL will be light and the window will blink. This function is to choose the exercise intensity level (L1~L10). You can or to change it to your required level and press ENTER to confirm. (2)After the level is confirmed,the TIME window will blink. Press or to set up the sport time. Or you can choose to press START directly to start move with count down. **Time range:20~99 min,the preset value is 30min,step is 1 min. 14

15 **If the machine has HRC function, P8 Custom will be replaced by HRC function. The operation ways are as follows: P8 HRC HRC function:(this function must be attached with heart beat to finish) The program aims to exercise heartbeat. When operating, the heartbeat value is equal to the pre-set value, the angle and speed will keep steady to maintain the heartbeat value in certain range to achieve the exercising effect. After you have selected this mode, the program will require you input the values according to following ways: 1. AGE LCD flashes and press or to adjust the age. After finish setting, press to enter next option. Age preset value:30. Range:13~80,Step is At this time LCD of PULSE light flashes, the mode will request you to put in heartbeat value. The value will change according to the age and please refer to the attached table in the rear of this indication. Then select the suitable value in the table. You can press or to adjust heartbeat value. If you don t make any change, press and mode will start according to pre-set value and turn to next position. 3. TIME window starts flashing, mode will request you to put in time value. You can press or to set sport time you need. Or press directly to start exercise with no countback. (* Range of time:20~99 min,pre-set value is 0 min,step is 1.) ** The chart below will show the relationship between different age and heart rate of this product of HRC function: 15

16 Age BPM Age BPM Age BPM Age BPM H Pre-set L H Pre-set L H Pre-set L H Pre-set L Error Signal Display: E1:The treadmill can t read the speed value. E6:In the range of ADC, incline motor doesn t run. E7:Incline is too height or too low(exceed the range). ** If it has any error signal, please connect with the sale agent 16

17 17

18 Note:The machine has a function to switch between the metric system and the inch system, the switch operation method: Hold the ENTER key for 10 seconds at the Start/Ready position after power on. At this time, the window will display: 0(the inch system) you can press +- key to select. After select, press ENTER to confirm and then you can make the change. 1(the metric system) SPEED AND ELEVATION CHANGES 9 HOLE Level 1 ELEVATION (MPH) (KPH) Level 2 ELEVATION (MPH) (KPH) Level 3 ELEVATION (MPH) (KPH) Level 4 ELEVATION (MPH) (KPH) Level 5 ELEVATION (MPH) (KPH) Level 6 ELEVATION (MPH) (KPH) Level 7 ELEVATION (MPH) (KPH) Level 8 ELEVATION (MPH) (KPH) Level 9 ELEVATION (MPH) (KPH) Level 10 ELEVATION

19 (MPH) (KPH) SPEED AND ELEVATION CHANGES HILL CLIMB Level 1 ELEVATION (MPH) (KPH) Level 2 ELEVATION (MPH) (KPH) Level 3 ELEVATION (MPH) (KPH) Level 4 ELEVATION (MPH) (KPH) Level 5 ELEVATION (MPH) (KPH) Level 6 ELEVATION (MPH) (KPH) Level 7 ELEVATION (MPH) (KPH) Level 8 ELEVATION (MPH) (KPH) Level 9 ELEVATION (MPH) (KPH) Level 10 ELEVATION (MPH) (KPH)

20 SPEED AND ELEVATION CHANGES HILL RUN Level 1 ELEVATION (MPH) (KPH) Level 2 ELEVATION (MPH) (KPH) Level 3 ELEVATION (MPH) (KPH) Level 4 ELEVATION (MPH) (KPH) Level 5 ELEVATION (MPH) (KPH) Level 6 ELEVATION (MPH) (KPH) Level 7 ELEVATION (MPH) (KPH) Level 8 ELEVATION (MPH) (KPH) Level 9 ELEVATION (MPH) (KPH) Level 10 ELEVATION (MPH) (KPH)

21 SPEED CHANGES ONLY INTERVAL Level 1 (MPH) (KPH) Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 (MPH) (KPH) (MPH) (KPH) (MPH) (KPH) (MPH) (KPH) (MPH) (KPH) (MPH) (KPH) (MPH) (KPH)

22 Level 9 Level 10 (MPH) (KPH) (MPH) (KPH) SPEED CHANGES ONLY ROLLING Level 1 (MPH) (KPH) Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 (MPH) (KPH) (MPH) (KPH) (MPH) (KPH) (MPH) (KPH) (MPH) (KPH) (MPH) (KPH) (MPH) (KPH)

23 Level 9 Level 10 (MPH) (KPH) (MPH) (KPH) SPEED CHANGES ONLY WEIGHT LOSS Level 1 (MPH) (KPH) Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 (MPH) (KPH) (MPH) (KPH) (MPH) (KPH) (MPH) (KPH) (MPH) (KPH) (MPH) (KPH) (MPH) (KPH)

24 Level 9 Level 10 (MPH) (KPH) (MPH) (KPH)

25 25