High Capacity Forklift Trucks H F

Transcription

1 High Capacity Forklift Trucks H F mm

2 H20.00F, H22.00F, H25.00F, H28.00F, H32.00F Specification data is based on VDI 2198 NOTE: Bottom of forks Specifications are affected by the conditions Stacking aisle width (line 4.33) is based on the V.D.I. standard calculation as shown on illustration. of the vehicle and how it is equipped, as The British Industrial Truck Association recommends the addition of 100 mm to the total clearance well as the nature and condition of the 02 operating area. If these specifications are critical, the proposed application should be (dimension a) for extra operating margin at the rear of the truck. Consult your Hyster lift truck dealer discussed with your dealer. Forklift Traders P/L Ph:

3 Ast = W a + x + b + a (see line 4.33) a = Minimum operating clearance (V.D.I. standard = 200 mm BITA recommendation = 300 mm) b = Load Length Rated Load (kg) H32.00F H28.00F H25.00F H22.00F H20.00F Load Centre Distance from front of forks to centre of gravity of load. Rated Load Based on vertical masts up to mm to top of forks. Load Centre (mm) Gradeability figures (lines 5.7 & 5.8) are provided for comparison of tractive performance, but are not intended to endorse the operation of the vehicle on the stated inclines. Follow instructions in the operating manual regarding operation on inclines. Noise level based on the weighting values contained in EN12053 Noise level measured according to 2000/14/EC directive Hyster products are subject to change without notice. Lift trucks illustrated may feature optional equipment. Safety: This truck conforms to the current EU requirements. 03

4 Mast and Capacity information Values shown are for standard equipment. When using non-standard equipment, these values may change. Please contact your Hyster dealer for information. Special lift heights are available. The rated capacities shown are for masts in a vertical position on trucks equipped with standard or sideshift carriage, and nominal length forks. Masts above the maximum fork heights shown in the mast table are classified as high and depending on the tyre/tread configuration may require reduced capacity, restricted back tilt or wide tread. The capacities quoted are in conformance with the ISO 1074 standard for stacking and travelling. 04

5 Product Features Instruments/accessories: Warning lights Engine oil pressure, transmission oil pressure and temperature, discharge indicator, low brake oil pressure, parking brake on, indicator lights. Gauges Engine coolant, fuel, transmission oil pressure, transmission oil temperature, voltmeter, engine oil pressure. Other indicators Hour meter, low brake pressure buzzer, combination key-type ignition, starter switch with starter lock out, audible reverse-warning alarm. Optional equipment: Masts: 'Vista' 2-stage masts with special lift heights Two-stage Full Free Lift masts Three-stage masts Extra hydraulic functions and hose groups, 5, 6 or 7 way. Air-conditioning Lifting eyes (2 on mast, 2 on rear frame) Spare wheel - front or rear (complete tyre and rim) 20'-40' telescoping container handling spreader, either low-mounted on mm long low forks, or high-mounted on m long inverted forks or dedicated (mounted on a dedicated carriage) Coil handling ram 05

6 Product Features Proven performance The Hyster H F series benefits from Hyster's long experience in providing cargo handling forklift trucks for a wide range of heavy-duty applications. These machines provide an excellent return on investment with an outstanding blend of uptime, fast handling and low running costs. Strength and durability The AxleTech drive axle is built to Hyster specifications and features one-piece drive shafts, planetary endreductions and offers wet disc brakes. The Hyster 'sandwich-type' steer axle, with a single, double-acting cylinder and fixed length tie rods, is renowned for its longevity and low maintenance requirements. The Dana speed powershift transmission has '12 plate' clutch packs and a cooling system with ample reserves. The fully automatic gear shifting system offers additional comfort for the operator and the forwardreverse shifting lock-out function protects the transmission against excessive wear. Clean power The Cummins QCS 8.3 diesel engine conforms to EU Tier 3 emissions requirements for NRMM (Non-Road Mobile Machinery). A turbocharger produces a smooth torque characteristic (a maximum of 915 Nm at rpm), providing durability and smooth engine performance, resulting in excellent acceleration and pulling power, combined with low fuel consumption. The heavy-duty 2-stage air filter with cyclonic precleaner is suitable for dusty operating environments. Ergonomic design The comprehensively equipped operator's cab is mounted on isolators, for improved sound reduction. Available in left- or centre-mounted positions and either as a cab or an open module, the operator compartment 06

7 is adaptable for optimum visibility in different Tailor made to your application applications or optimum comfort in different climates. There are three mast types are available 2-Stage Operator comfort is enhanced thanks to filtered fresh Limited Free Lift, 2-Stage Full Free Lift, and 3-Stage air, an interior fan and a fully adjustable, full Full Free Lift. These can be combined with either a suspension seat with armrests and high backrest. standard or integral sideshift carriage. The integral Finger light power steering, power-assisted hand sideshift carriage features full sideshift movement of controls and conveniently positioned instruments - +/- 300 mm in all fork positions. including push-button parking brake, responsive, fully All carriage types feature versatile independent fork- hydraulic brakes and an automotive type pedal layout positioners. Quick disconnect pin-type mountings are all contribute to enhance driver productivity. available for flexibility and rapid fork interchanges. The mid-high positioning of the cab, which features Forks are available in various configurations and coil glass-to-glass joints and wipers (with washers) on the handling rams, fork-mounted or dedicated container front, top and rear screens, for excellent all-round spreaders, and tailor-made attachments are also visibility together with the Hyster Vista mast offer available to suit a specific user's application. excellent operator visibility. 07 Forklift Traders P/L Ph: sales@flt.com.au

8 Product Features Equipment and weight: Weights (line 2.1) are based on: H F - Complete truck with mm mast, mm wide sideshift carriage and mm forks. H28.00F-32.00F - Complete truck with mm mast, mm wide sideshift carriage and mm forks. Fuel tank capacity: Total capacity = 246 litres Fork Spacing: Inside to inside minimum: mm (H F) 940 mm (H F) Outside to outside maximum: mm (H F) mm (H F) Carriages: Standard (non-sideshift), pin type (with hydraulic fork positioners). H F: mm wide H F: mm wide Integral Sideshift, pin type (with hydraulic fork positioners). H F: mm wide H F: mm wide Sideshift distance: 305 mm each side of centre (total 610 mm) Forks: H F 1) Forks for general cargo handling: mm long, pin type, section 120 x 200 mm. Note: These forks are NOT suitable for 20' ISO container pockets. 2) Slim-line forks for general cargo handling and 20' containers with ISO fork pockets: mm long, pin-type, slim-line section 102 x 280 mm. H F 1) Forks for general cargo handling and 20' containers with ISO fork pockets: mm long, pin-type, slim-line section 105 x 300 mm. 2) Low forks for a low-mounted container spreader, mm long, pin type, section 115 x 305 mm. Note: These forks are NOT suitable for 20' ISO container pockets. 3) Forks for a high-mounted container spreader, mm long, quick-disconnect pin type, section 115 x 305 mm. Note: These forks are NOT suitable for 20' ISO container pockets. Masts: Heights and types as specified. Special lift heights are available. 08

9 Engine: Cummins QCS cylinder in-line turbocharged diesel engine Max. power 172 kw ( rpm Smooth torque rpm 24 Volt electrical systems 70 Amp heavy-duty alternator with integral regulator and dust proof starter Two replacement cartridge type oil filters Heavy-duty air cleaner with cyclonic precleaner and outside high-level air intake Air restriction indicator shows when filter element needs service Overhead exhaust Cooling system: Heavy-duty radiator, puller type fan for cleaner air entry. Large heat exchanger cools transmission oil. Hydraulic system: Two mechanically driven gear pumps with 410 l/min maximum output and two pilot-operated main control valves with separate two-speed hoist valve. A flow amplifier diverts only the required amount of oil for steering; the remaining oil is used for the lift/tilt functions. Power assisted hand controls use a pilot supply from a 'piggy back' pump with an accumulator (common to the brake system). An automatic 2-speed lift system increases lift speed in no-load situations. Lights: A complete light kit is fitted as standard comprising: 4 front working and 2 rear working halogen lights; mounted on top of the cab; 2 headlights; 2 sidelights; 4 direction indicator lights and 2 tail & stop lights; plus a flashing beacon on top of cab. Brakes: Brake system: Fully Hydraulic, with accumulator (no air system). Service brake: Oil immersed (Wet Disc) at the drive wheels. The parking brake is auto-matically applied when hydraulic pressure falls below 80 bar. 09

10 Strong Partners, Tough Trucks, for Demanding Operations, Everywhere. Hyster supplies a complete range of warehouse equipment, IC and electric counterbalanced trucks, container handlers and reach stackers. Hyster is committed to being much more than a lift truck supplier. Our aim is to offer a complete partnership capable of responding to the full spectrum of materials handling issues: Whether you need professional consultancy on your fleet management, fully qualified service support, or reliable parts supply, you can depend on Hyster. Our network of highly trained dealers provides expert, responsive local support. They can offer cost-effective finance packages and introduce effectively managed maintenance programmes to ensure that you get the best possible value. Our business is dealing with your materials handling needs so you can focus on the success of your business today and in the future. Hyster Europe, Flagship House, Reading Road North, Fleet, Hants GU51 4WD, England. Tel: +44 (0) Fax: +44 (0) info@hyster.co.uk A division of NACCO Materials Handling Limited. 11/07/TLC Printed in England Form No Hyster,, & Monotrol are registered trademarks of Hyster Company in certain countries., Fortens, Pacesetter VSM, DuraMatch, DuraMatch Plus, TouchPoint, TouchControl, EZXchange, HSM & Vista are trademarks of Hyster Company in the United States and in certain countries where rights in unregistered trademarks are recognised.