SCREW-TYPE DISTRIBUTION BLOCKS
|
|
- Roger Francis
- 6 years ago
- Views:
Transcription
1 CONTA-CONNECT SCREW-TYPE DISTRIBUTION BLOCKS Our ideas Your advantages
2 CONTA-CONNECT Screw-distributor blocks SVB The SVB screw-type distributor block makes it possible to distribute potential and power in a compact space without any additional accessories. You can use the distributor block to establish an electromechanical connection between a wire with a large cross-section and one or more wires with small cross-sections. They can be used in installation and distribution board construction and also in controller construction for machinery. The SVB blocks are mounted by snapping them on to TS 35 DIN rails. They can also be attached directly to a mounting plate using the screw flange located on the side of the housing. 28
3 Screw-distributor blocks SVB Diagrams SVB 80 Diagram SVB 25 Diagram 2 SVB 75 Diagram 3 SVB 2 Diagram 4 SPECIAL TERMINALS SVB 400 Diagram 5 SVB 60 Diagram 6 SVB 75/3 Diagram 7 SVB 25/4 Diagram 8 29
4 Screw-distributor blocks SVB system Features High short-circuit resistance rating IP20-class protection Simple handling Space-saving design Foot base can be snapped on TS 35 DIN rail or suitable for direct mounting Modular design (single- or three-phase block) Suitable for copper wires Housing made from polyamide 6.6 UL 94- SVB 80 CONTA-CONNECT SVB 25 SVB 75 Diagram Page 29 Diagram 2 Page 29 Diagram 3 Page 29 7 connections 8 connections connections Connection type Dimensions (L x W x H), directly installed, mm Size (L x W x H) with TS 35 x 7.5 mm Weight, g Type Type Colours available Ratings Rated voltage, V Rated current, A Rated cross-section for input and output, mm 2 Rated cross-section for input and output, AWG Rated impulse voltage, kv Contamination degree Flamm. class UL 94 Short-circuit resistance rating Short-circuit current resistance IPK (peak value), ka Short-circuit current resistance ICW over s, ka SCCR rating kv Class J series fuse required, A Connection data Inputs Number of connections Clampable wire: mm 2 e single wire H07V-U m stranded H07V-R f finely stranded H07V-K f finely stranded H07V-K and ferrule DIN / f finely stranded H07V-K and ferrule with plastic collar Diameter mm Torque Nm Terminal screw Blade size Stripping length mm Outputs Number of connections Clampable wire: mm 2 e single wire H07V-U m stranded H07V-R f finely stranded H07V-K f finely stranded H07V-K and ferrule DIN / f finely stranded H07V-K and ferrule with plastic collar Diameter mm Torque Nm Terminal screw Blade size Stripping length mm Accessories End stop ES Allen key socket wrench ISKS Allen key socket wrench ISKS Screwdriver SDK Screwdriver SDK Additional accessories 66 x 27 x x 27 x 63 SVB 80 LG ,7, ,5 3 PZ , ,5 M4 PZ2 PZ SDK,0x SDK,0x x 27 x x 27 x 34 SVB 25 LG , ,5-5 3,5-5 M8 M6 M4 M PZ2 0-2 SDK,0x x 45 x 43 7 x 45 x SVB 75 LG M M6 M3 0-2 ISKS More accessories starting on page
5 SVB 2 SVB 400 SVB 60 SVB 75/3 SVB 25/4 Diagram 4 Page 29 Diagram 5 Page 29 Diagram 6 Page 29 Diagram 7 Page 29 Diagram 8 Page 29 2 connections 2 connections 7 connections with busbar distribution 3 x 7 connections 3 x 8 connections with neutral busbar 96 x 44 x 96 x 44 x SVB 2 LG 743 IEC UL () 96 x 44 x 96 x 44 x SVB 400 LG 744 IEC UL / x 35 x 92 x 35 x SVB 60 LG / x 80 x 43 7 x 80 x SVB 75/3 LG x 98 x 74 x 98 x SVB 25/4 LG 747 IEC SPECIAL TERMINALS , M4 M , M8 M6 M6.2 x x x ISKS SDB 0.8x4 087 SDB.2x M6 M , M8 M6 M6.2 x x x ISKS SDB 0.8x4 087 SDB.2x M0 6-8 A Busbar 6 6 x 5 mm max M6 PZ ISKS ISKS x M x M6 M3 0-2 ISKS ISKS x 3 x 5 3 x ,5 0.8,5 M4 PZ2 PZ PZ Neutral wire Neutral wire Neutral wire ,5 0.8,5 M4 PZ2 PZ PZ SDK,0x SDK,0x
6 GB 08 All rights reserved. Otto-Hahn-Str. 7 D-336Hövelhof Phone +49 (0) Fax +49 (0) info@conta-clip.com
SCREW-TYPE DISTRIBUTION BLOCKS
SCREW-TYPE DISTRIBUTION BLOCKS PRODUCT INFORMATION CONTA-CONNECT Screw-distributor blocks SVB The SVB screw-type distributor block makes it possible to distribute potential and power in a compact space
More informationDOUBLE-LEVEL TERMINAL BLOCKS SRKD SSLD
DOUBLE-LEVEL TERMINAL BLOCKS SRKD SSLD PRODUCT INFORMATION Double-level terminal blocks SRKD SSLD CONTA-CLIP offers an innovative line of double-level feed-through terminals SRKD and protective-earth terminals
More informationCONTA-CONNECT SUPPLEMENTS
CONTA-CONNECT SUPPLEMENTS CONTA-CONNECT system HSKG High-power stud terminals HSKG The newest generation of stud terminals from CONTA-CLIP offers secure connections for all energy-transmitting applications.
More informationFEED-THROUGH TERMINALS SDK
FEE-THROUGH TERMINALS SK PROUT INFORMATION ONTA-ONNET Feed-through terminals SK ONTA-LIP's SKs feed-through terminals provide a modular-based system for various device and housing applications. The coordinated
More informationData sheet... W-Series WPE 4
The PE terminals are available in two designs: standard and compact (N), with rated cross-section from 1.5 mm² to 150 mm² (e.g. 2.5 mm² WPE 2.5 or 4 mm² WPE 4N). General ordering data Order No. 1010100000
More informationData sheet... W terminal earth terminal WPE 4
The PE terminals are available in two designs: standard and compact (N), with rated cross-section from 1.5 mm² to 150 mm² (e.g. 2.5 mm² WPE 2.5 or 4 mm² N). General ordering data Order No. 1010100000 Type
More informationDatasheet. W-series terminal with clamping yoke connection WSI 6
The fuse terminals of the Weidmüller W Series are available in two different forms: Fuse terminal with pivoting retaining lever Fuse terminal with plug-in SIHA fuse holder General ordering data Order No.
More informationCONTA-CONNECT. Disconnect terminals TRK/STK 2/TK
CONTACONNECT s TRK/STK 2/TK s are commonly used within measurement and control systems. They provide assistance when troubleshooting in electrical facilities, when commissioning new facilities and when
More informationSHIELD-CONNECTION CLIPS SAB
SHIELD-CONNECTION CLIPS SAB PRODUCT INFORMATION CONTA-ELECTRONICS Shield-connection clips SAB Overview of the product line Description of the SABK shield-connection bracket system 3 Shield-connection bracket
More informationCONTA-CONNECT. Double-level terminal blocks ZRKD 2,5 Double-level protective earth terminal ZSLD 2,5
CONTA-CONNECT Double-level terminal blocks ZRKD 2,5 Double-level protective earth terminal ZSLD 2,5 With a width of just 5 mm, the new ZRKD series is available in thirteen versions and connects with stranded
More informationData sheet. W-Series WDU 4 SL/EN
At Weidmüller, new solutions for the energy sector are developed according to local or application-based installation requirements. In some countries, control and protection of switching installations
More informationDatasheet. W-series terminal with clamping yoke connection WDU 2.5 RT
The versatile and extensive range of products - from 0.05 mm² to 300 mm² - means that you have diverse options for your applications at your disposal. Hardened steel for mechanical strength and high-quality
More informationDatasheet. W-series terminal with clamping yoke connection WDU 4
The versatile and extensive range of products - from 0.05 mm² to 300 mm² - means that you have diverse options for your applications at your disposal. Hardened steel for mechanical strength and high-quality
More informationDatasheet. BL/SL 5.08 series BLF 5.08/02/180 SN OR BX
Just as reliable as the tried-and-tested original, with innovation in detail: the BLF 5.08 the PUSH-IN version of the BLZ 5.08 female header features a new connection system and a more compact design.
More informationPowermate Range pitch 7.00 Powermate Range pitch 7.00
Contents lug and socket connectors with leaf spring connection.2 lug and socket connectors with TO connection.6.1 lug and socket connectors with leaf spring connection STVS S Derating curve STVS SB Socket
More informationPCB plug-in connectors
Contents CB plug-in connectors.16 mm pitch.16 mm pitch Male connectors with solder connection.2 Socket connectors with clamping yoke connection.8.1 Male connectors with solder connection SU.16H/9 Derating
More informationStud connection system HSK
CONTA-CONNECT system HSK The newest generation of stud terminals from CONTA-CLIP offers secure connections for all energy-transmitting applications. Depending on the conductor cross-section, stud terminals
More informationCONTA-CONNECT. Overview. Overview... 2 Our company... 3
SUPPLEMENTS CONTA-CONNECT Overview Overview... 2 Our company... 3 system SRK SSL... 4 Feed-through terminals SRK Protective earth terminals SSL... 8 Double-level terminal blocks SRKD SSLD... 6 Pick-off
More informationD a t a s h e e t W P D B P o w e r D i s t r i b u t i o n B l o c k s 508A 100kA Canada Mexico United States
Datasheet WPDB Now you can manage multiple load connections and a wide range of wire sizes with Weidmuller s Power Distribution blocks. By using the best materials and the best technology, Wedimuller provides
More informationINNOZED D0 fuse-bases with touch protection
INNOZED D0 fusebases with touch protection INNOZED D0 fusebases with touch protection FUSE HOLDERS, FUSE BASES AND SUPPORTS IEC D0 & D FUSE BASES FEATURES & BENEFITS INNOZED is a fuse base for D0 fuselinks,
More informationFemale socket block, Screw connection, No. of poles: 12, Width: mm, Colour: Green
Female socket block, Screw connection, No. of poles: 12, Width: 45.72 mm, Colour: Green Business data Connector version Free connector Packaging unit 50 Quantity unit PC Packaging type Carton Type of banding
More informationHan Q 1/0 Axial Screw Protected. Available February 2017
Features Compact connector based on size 3 A with a current carrying capacity of 100 A Space saving design due to an angled malemale version IP20 protected male and female contact according to IEC 60 529
More informationDatasheet. System pitch mm (0.400 inch) - SU/BU BUZ 10.16HP/02/180F AG BK BX
High-performance female connector with the tried-and-tested, guaranteed zero-maintenance, Weidmüller steel clamping yoke. Side-by-side mounting without losing any poles or with patented multifunction flange
More informationTerminal blocks with clamping yoke and screw connection system
Overview W-Series Terminal blocks with clamping yoke and screw connection system High contact reliability for all standard electrical functions For a long time now, Weidmüller s W-Series terminal with
More informationCrimpmate Range pitch 5.00
Contents pitch. pitch. pitch. Male and female connectors with solder connection. Male and female connectors with crimp connection. Crimp contacts..1 pitch. RSV 1. S Derating curve RSV1. S SN Rectangular
More informationINNOZED D0 fuse-bases with touch protection
D0 fusebases with touch protection D0 fusebases with touch protection FUSE HOLDERS, FUSE BASES AND SUPPORTS IEC D0 & D FUSE BASES FEATURES & BENEFITS is a fuse base for D0 fuselinks, sizes D0 and D02.
More informationAF40... AF96 3-pole contactors Technical data
Main pole - Utilization characteristics according to IEC Standards IEC 60947- / 60947-4- and EN 60947- / 60947-4- Rated operational voltage Ue max. 690 V Rated frequency (without derating) 50 / 60 Hz Conventional
More informationDBL distribution blocks 3x1 pole
TECHNICAL DATASHEET 1SNC166019D0201 - CATALOGUE PAGE 1SNC166020S0201 DBL distribution blocks 3x1 pole 84.6 3.33" 25 0.98" 32.5 1.28" 28.2 1.11" 23.5 0.93" 14.7 0.58" 36.3 1.43" 75 2.95" 62 2.44" 50.7 2"
More informationEKB 1,5/...DS M 2,6 M 2,6 M 3. Cuttable terminal 1.5 mm 2 with wire protection. Screw connection. 95.4* x 18 x 14. Qty. Length, mm
Cuttable terminal strips EKB system EKB,5/...DS EKB,5/... EKB /...DS The EKB variants cover a rated crosssection range from.5 to 0 mm2. They are available from to 2 poles. An attachment hole is located
More informationFeed-through terminal, 2.5 mm², Tension clamp connection, Wemid, dark beige, TS 35
General ordering data Order No. 1608570000 Part designation 2.5/4AN Version EAN 4008190077136 Qty. 100 pc(s). Feed-through terminal,, Tension clamp connection, Wemid, Product notes Product description
More informationSnap-in covers I Voltage taps
ACCESSORIES Accessories for analogue instruments, current transformers, switchboards, voltage taps for busbars and round conductors. Snap-in covers I Voltage taps Voltage taps page 10/1 10 For analogue
More informationDatasheet. Approvals. Technical data. Feed-through terminal WK 4 / U BLUE /V0. General. Technical data. Connection Data
Datasheet Art.No. 57.504.0055.6 Feed-through terminal WK 4 / U BLUE /V0 Feed-through DIN rail terminal block with screw connection for mounting on TS 35 and TS 32, nominal cross section 4 mm², width 6
More informationZS4-SF1 Screw Clamp Terminal Block
Technical Datasheet 1SNK 161 011 D0201 ZS4-SF1 Screw Clamp Terminal Block Fuse Catalogue Page 1SNK 161 011 S0201 4 mm² 10 AWG 8 mm 0.315 in Spacing Features and Benefits 90 90 180 59.7 2.35" - Protect
More informationViking 3 - Screw connection Disconnect terminal blocks
87045 LIMOGES Cedex Telephone: (+33) 05 55 06 87 87 - Fax: (+33) 05 55 06 88 88 Viking 3 - Screw connection 1. General features... 1 2. Range...2 3. Standards... 2 4. Technical features... 3 5. Dimensions...
More informationFUSE BASES NH FUSE BASES 690V 160A 160A
fuse bases NH NH 14 690V NH 16 ACCESSORIES FOR NH 18 CR 690V NH 20 SECTIONABLE NEUTRAL NH BASES 21 BS FUSE SWITCH DISCONNECTORS 690V NH NH Fuse bases for NH fuse links. For mounting on DIN/EN rail or
More informationCSF - CSM CONNECTORS. Functional characteristics. RoHS 2011/65/EU. Brief description. Dimensional class: low. Standard colour: green
- CSM Functional characteristics Dimensional class: low 0 RoHS 2011/65/EU Standard colour: green Dimensions: 14 x 11.5 mm (.551 x.453 in) 10 20 30 mm ½ 1 in Max approved wire size: solid: 2.5 mm 2 (IMQ);
More informationApplication Coding Cable diameter Color Part No. Std. Pack Part No. Std. Pack. Female connector. gray black gray black gray black green
Connectors Connector for cables of Ø 6 10 and 10 14 mm With spring clamp connections for rigid cables of 0.5 2.5 mm 2, f fine-stranded cables of 0.5 1.5 mm 2 with ferrules, stranded cables of 0.75 1.5
More informationDatasheet AC Outlet DIN-Rail Mountable Receptacles
Datasheet AC Outlet DIN-Rail Mountable Receptacles DIN-rail receptacles, 5A, 15A and 20A power outlets, provide a convenient power source for portable computers or test devices for in-the-panel troubleshooting.
More informationMSW. MSW Catalog Number Sequence. Standard Features MSW 25 B- 3
Introducing the New WEG Series. The was developed according to IEC 60947-3 & UL508. The compact, reliable design of the allows the operator to safely disconnect power and isolate the circuit within the
More informationNEW. Datasheet. WMF 2.5 Terminal Series
Datasheet WMF 2.5 Terminal Series NEW The WMF 2.5 (multi-functional) terminal series is uniquely designed for DCS marshalling where increased functionality, improved spacing, higher wiring density and
More informationData sheet... OMNIMATE Signal - series LM LM 5.00/04/90 3.5SN OR BX
PCB terminal with proven clamping yoke connection at 5.00 and 5.08 mm pitch. Conductor outlet direction 90, 135 and 180. Suitable for conductor cross-sections up to 2.5 mm². 0.13-2.50 mm² (IEC) / 26-14
More informationPrintview: Stackable PCB terminal block; 16 mm²; Pin spacing 15 mm; 1-pole; CAGE CLAMP ; commoning option - Item No.
Stackable PCB terminal block; 16 mm²; Pin spacing 15 mm; 1- pole; CAGE CLAMP ; commoning option Item No: 745-871/006-000 Stackable PCB terminal block; 16 mm²; Pin spacing 15 mm; 1-pole; CAGE CLAMP ; commoning
More informationHK-003,HC SERIES HK-003 HCSERIES. Modular Heavy-current connector WAIN 12-01
HK-00, SERIES HK-00 SERIES Modular Heavy-current connector 12-01 HK-00/0HK-00/2 Heavy-current inserts HE-006 HK-00 Technical characteristics Specifications Approvals Inserts Number of contacts Electrical
More informationNon-Fused Load Break Switches FSSC, SX, SXDC, SC
Non-Fused Load Break Switches FSSC, SX, SXDC, SC UL 98 Non-Fused Load Break Switches Mersen disconnect switches are extremely durable, manually operated, non-fused disconnect switches. These heavy-duty
More informationModulostar CMS10 Modular fuse-holders
Modulostar CMS10 FUSE HOLDERS, FUSE BASES AND SUPPORTS IEC CYLINDRICAL FUSE HOLDERS FEATURES & BENEFITS The innovative and comprehensive Modulostar range of Mersen fuse-holders. are finger-safe under IEC
More informationPowerLine OS Switch Fuses A, 690V
Technical Brochure PowerLine OS Switch Fuses 20...160 A, 690V Brochure OS 10 GB 99-04 9902CD04 ABB Control New Switch Fuse Range 2 3 Total user safety Total user safety Fuse carriers fully IP20 protected
More informationOperating voltage up to 5 kvdc Operating current up to 4,5 A 2-6 high voltage contacts Quick and easy assembling Protection class IP68 acc.
Operating voltage up to 5 kvdc Operating current up to 4,5 A 2-6 high voltage contacts Quick and easy assembling Protection class IP68 acc. DIN EN 60529 General characteristics and technical data Series
More informationLINOCUR Size D02 63A 230VAC/440VAC
IEC FUSE SWITCH DISCONNECTORS D0 FUSE COMBINATION UNITS The D0 Linocur is a combination of switch disconnector fuse and Neozed 63A fuse-link, equiped with significant safety characeristics and sophisticated
More informationMULTIBLOC 2.RST8 Size 2, 400A, 690VAC, Design for bus bar installation, Triple Pole
MULTIBLOC 2.RST8 IEC FUSE SWITCH DISCONNECTORS NH FUSE SWITCH DISCONNECTOR The production programme of MULTIBLOC 2.RST8 comprises NH fuse switch disconnectors for 400A. Products are designed in triple
More informationHan ES Press. Features. Description. Removal of conductor. Size 6 B - 24 B
Size 6 B - 24 B Features Easy bridging functionality of contacts by means of plug-in jumpers directly on the connector Fast realisation of potential multiplication as well as star and delta bridges Rapid
More informationRated voltage (V) Current (A) Stranded wire. Solid wire A.D.O. (AWG)
Characteristics (1) Dimensions are on DIN 3 rail : PR4 (Height 15 mm) Use of a PR3 rail : remove 7,5 mm on dimension B Use of a DIN 1 rail : remove 2,5 mm on dimension B remove 5 mm on dimension C Miniblocks
More informationElectronic Circuit Breaker ESS20-0..
Electronic Circuit Breaker ES-0.. Description Electronic circuit breaker type ES-0.. is designed to ensure selective disconnection of individual loads in systems which are powered by a DC 4 V switch-mode
More informationModulostar US10 Modular fuse-holders
Modulostar US10 FUSE HOLDERS, FUSE BASES AND SUPPORTS UL/CSA FUSE HOLDERS FEATURES & BENEFITS The innovative and comprehensive Modulostar range of Mersen fuse-holders. are finger-safe under IEC standards
More information8WH2 Spring-Loaded Terminals
8WH2 Spring-Loaded Terminals /2 Introduction /3 General data on 8WH /7 8WH through-type terminals 1) /18 8WH hybrid through-type terminals 1) /21 8WH fuse terminals /23 8WH isolating blade terminals /25
More informationMulti-pole terminal strips
Contents for direct mounting Screw connection.2 Screw connection ATEX approval.6.1 for direct mounting Screw connection MK 2/12 2.5 MK 3/2...12 2.5 Width/Height/ø mounting hole Length / mounting dimensions
More informationData sheet TERMSERIES TRZ 120VUC 1CO
relay module, complete modules consisting of a relay and a base with AC/DC/UC coils, available in different versions: With screw and tension-clamp connection AgNi contact, optionally with hard gold-plated
More informationMain catalogue. SNK Series Terminal Blocks Accessories Marking Solutions
Main catalogue SNK Series Terminal Blocks Accessories Marking Solutions Summary See page 7 1SNK161026S0201 SNK Series, Terminal Blocks Screw clamp terminal blocks Accessories Marking solutions 1 A Smart
More informationSafety Switches Series 8537
Safety Switches www.stahl.de > 3- and 6-pole switches 12 / 16, 25, 40, 63 / 80, 125 / 160, 250, 315, 400, 500 A > Motor switching capacity AC-3 and AC-23 acc. to IEC 60947-3, EN 60947, DIN VDE 0660 part
More information- 1 - General ordering data Order No
General ordering data Order No. 1748280000 Part designation B2L 3.5/28 F SN SW Version EAN 4032248156535 Qty. 20 pc(s). PCB plug-in connector, Female connectors, Tension clamp connection, Clamping range,
More informationLoad Break Disconnect Switches FSLBS
Load Break Disconnect Switches FSLBS UL 508 Non-Fused Load Break Switches The FSLBS Load Break Switch is a newly designed industrial-grade switch capable of making or breaking loads up to 600V. It is suitable
More informationOperating voltage up to 5 kvdc Operating current up to 4,5 A 2-6 High voltage contacts Quick and easy assembling Protection class IP68 acc.
Operating voltage up to 5 kvdc Operating current up to 4,5 A 2-6 High voltage contacts Quick and easy assembling Protection class IP68 acc. DIN EN 60529 General characteristics and technical data Series
More information8WH2 Spring-Loaded Terminals
8WH2 Spring-Loaded Terminals /2 Introduction /3 General data on 8WH /7 8WH through-type terminals 1) /18 8WH hybrid through-type terminals 1) /21 8WH fuse terminals /23 8WH isolating blade terminals /25
More informationCylindrical fuse-link
Cylindrical fuse-link Technical data Rated voltage Rated current Rated frequency Rated breaking capacity Characteristics ody material 00 V AC, 00 V AC, 90 V AC CH 8 - A/00 V CH 0,- A/00 V, 0-3 A/00 V CH
More informationINDUSTRIAL COMPONENTS CATALOGUE. Terminals, switches and fuse bases
INDUSTRIAL COMPONENTS CATALOGUE Terminals, switches and fuse bases 2 Ensto at your service Ensto is an international industrial group and a family business specialising in the development, manufacture
More informationOperating voltage from 10 KVDC to 15 kvdc. Operating current up to 13 A. 2-5 HV contacts. For cable sizes AWG 26-14
Operating voltage from 10 KVDC to 15 kvdc Operating current up to 1 A 2-5 HV contacts For cable sizes AWG 26-14 Overview Series MC P/N Description Plug Receptacle Cable mount Panel mount Coupling HV-pins
More informationAF40... AF96 3-pole contactors 30 to 60 hp at 480 V AC AC / DC operated with 1 N.O. + 1 N.C. auxiliary contacts
AF4... AF96 -pole contactors to 6 hp at 48 V AC AC / DC operated with N.O. N.C. auxiliary contacts Description AF4... AF96 contactors are mainly used for controlling -phase motors and power circuits up
More informationCONTA-CONNECT. High-power stud terminals HSK. a b
CONTACONNECT Highpower stud terminals HSK The newest generation of stud terminals from CONTACLIP offers a secure connection for all energytransmitting applications. Depending on the conductor crosssection,
More informationMULTIBLOC 3.ST8 Size 3, 630A, 690VAC, Design for Bottom Fitting, 3-,4-pole
MULTIBLOC 3.ST8 IEC FUSE SWITCH DISCONNECTORS NH FUSE SWITCH DISCONNECTOR The production programme of MULTIBLOC series 3.ST8 comprises NH fuse switch disconnectors for 630A. They are designed for bottom
More informationLimitor -G General Purpose Fuses
Limitor -G General Purpose Fuses HIGH VOLTAGE IEC FUSES DIN HV GENERAL PURPOSE FUSES FOR TRANSFORMERS FEATURES & BENEFITS Mersen HV fuse-links have been used for reliable protection in high-voltage switchgear
More informationGeneral characteristics and technical data Series MCS
MOD M MC MCS VP 100 S Operating voltage up to 5 kvdc Operating current up to 4,5 A 2-6 high voltage contacts Quick and easy assembling Protection class IP68 acc. DIN EN 60529 General characteristics and
More informationSwitches for photovoltaic applications Disconnect switches, UL OTDC_U from 16 to 32 Amperes
Switches for photovoltaic applications Disconnect switches, UL OTDC_U from 16 to 32 Amperes OTDC16...32U - Compact efficiency OTDC from 16 to 32 amperes offers various DC voltage ratings and a control
More informationThermal overload relay TF65 and TF96
Data sheet Thermal overload relay TF65 and TF96 Thermal overload relays are economic electromechanical protection devices for the main circuit. They are used mainly to protect motors against overload and
More informationThermal-Magnetic Circuit Breaker 201/-WA
Thermal-Magnetic Circuit Breaker 0/-WA Description Single pole thermal-magnetic circuit breaker with tease-free, trip-free, snap action mechanism and two button operation (M-type TM CBE to EN 60934). Featuring
More informationFuse switch disconnectors
SWITCHGEAR 62 RBK pro Fuse switch disconnectors designed for distribution of electricity and protection of electrical equipment against short-circuits and overloads with industrial fuse links. ENERGY SAFELY
More informationBETA Switching Switches and Light Indicators
Siemens AG 2008 BETA Switching /2 Product overview /3 5TE8 control switches / 5TE4 pushbuttons /2 5TE5 light indicators /5 5TE8 ON/OFF switches /22 5TE9 busbars /24 5TE switch disconnectors Siemens ET
More informationApprovals (p. 906) 0 371 61 0 371 63 0 371 64 0 371 66 0 371 69 0 371 68 0 371 00 0 371 08 0 371 20 Connecting (p. 300) 1 connection - 1 entry/1 outlet ELECTRICAL FUNCTION TERMINAL BLOCKS INSULATION EQUIPOTENTIAL
More informationThermal Overload Relays - WEG RW Series, 2 Pole
International (5) 4-07 The RW Class Thermal Overload Relays, with their extended operational service lives, are designed for use with the CWC miniature and CWM standard contactors. These relays can be
More informationOMNIMATE Power PCB terminals
Contents OMNIMTE ower OMNIMTE ower OMNIMTE ower Clamping yoke screw connection Explanation.2 Quick selection.4 roduct selection dimension 6.35.6 dimension 10.16.8 dimension 12.70.11 dimension 15.00.12.1
More informationVistop TM isolating switches 63 to 160A
DX 3 - IS main switches 16 to 125A Vistop TM isolating switches 63 to 160A 225 15 225 18 4 064 00 4 064 59 Pack Cat. No. Main switches AC 22 A category as per EN607-3 Grey handle Accept 1 signalling auxiliary
More informationChapter 06 Accessories ACCESSORIES
ccessories CCESSORIES 57 Powerful and precise Input, 3-pole Output is 3-pole + N Use in IT networks without neutral line For reducing the measurement voltage for the UMG measurement input Use in IT networks
More information25A 25A 32A 40A 40A 63A 63A 80A
ISDC Compact Range 25A - 200A Control Panel Isolation Equipment Craig & Derricott has ranges of Switch-Disconnectors, Fuse Combination Units and Changeover Isolators for panel mounting ranging from 25A
More informationMULTIBLOC 1.RST8 Size 1, 250A, 690VAC, Design for bus bar installation, Triple Pole
MULTIBLOC 1.RST8 IEC FUSE SWITCH DISCONNECTORS NH FUSE SWITCH DISCONNECTOR The production programme of MULTIBLOC 1.RST8 comprises NH fuse switch disconnectors for 250A. Products are designed in triple
More informationBasic function. Rated current. Appropriate for three-phase motors of output 2) [kw] I n. = 400 V a.c. 2) Appropriate for three-phase motors
MOTOR STARTERS SM Basic function Switching and protection of motors up to A Protection against short-circuit and protection against overload The device responds to phase failure The device is provided
More informationAltech UL1077/508 Busbar System
Altech UL1077/508 Busbar System UL1077/508 Listed Busbars The Altech Busbar System is an innovative way to jumper up to 57 poles of Manual Motor Controllers (MMC) and Supplementary Protectors (SP). The
More informationCABINETS AND ENCLOSURES. XL³ 400 and XL³ 800 GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES
O S O O CABINETS AND ENCLOSURES XL³ 400 and XL³ 800 GLOBAL SPECIALIST IN ELECTRICAL AND DIGITAL BUILDING INFRASTRUCTURES II With its extensive ranges, the Legrand offer meets your quality standards and
More informationMK 2/ mm 2 IEC UL CSA. IEC UL CSA Rated voltage AWG AWG AWG AWG Rated surge voltage / pollution severity
or direct mounting Screw connection MK 2/12 2.5 mm 2 MK 3/2... 12 2.5 mm 2 Width x height / ø fixing hole mm 15.0 x 15.0 / 3.20 15.0 x 16.1 / 3.45 (length and mounting size: see order data) Max. clamping
More informationGV2, GV3, and GV7 Manual Motor Starters, Controllers, and Protectors Standard Features
Standard Features Table : Standard Features GV2ME GV2P GV3P GV7RE/GV7RS 0. to 32 A Up to 20 hp @ 460 V 0 SCCR @ 480 V Push Button Operator 0. to 30 A Up to 5 hp @ 460 V 50 SCCR @ 480 V Rotary Handle Operator
More informationVarius SUMMARY OF MODELS
SUMMARY OF MODELS Type 10 14 22 OPT22/OPT20 OPVF10 Rated operating current I e / Rated current I n 32 A / - 63 A / - 125 A / - 63 A / - - / 30 A Rated operating voltage U e / Rated voltage U n AC 690 V
More informationInterchangeable Built-in Fixed thermal Adjustable thermal Magnetic Fixed Adjustable Adjustable Electronic RMS 7 LS LSI
. Technical Data and Specifications Ratings Frames EG, JG and LG EG JG LG Maximum rated current (amperes) 15, 160 1 50 400, 630 Breaker type 3 B B E S S H H C E S H C U X E S H C U X of poles 1, 3, 4,
More informationUnimate Range Pitch 5.08
itch 5.08 in headers Socket connectors CB connection Solder connection SLA 90 250 V / 17.5 A SLA 180 250 V / 17.5 A.2.3 Cable connection Clamping yoke connection TO clamp connection BLA 250 V / 17,5 A
More informationMini contactors B6, BC6 with 3 pole
Data sheet Mini contactors B6, BC6 with 3 pole Mini contactors from ABB are used for remotely ling motors and other loads wherever space is at a premium. These devices feature hum free coils, shallow depth,
More informationW DATA SHEET: COMBINED FAULT-CURRENT PROTECTIVE SWITCH, SERIES BOLF, 3P+N
W DATA SHEET: COMBINED FAULT-CURRENT PROTECTIVE SWITCH, SERIES BOLF, 3P+N W SCHRACK-INFO Typ A (pulse) Connection on both sides are possible Tripping independent of line voltage Additional connection capability
More informationMS /27/2015. ABB contact for United States of America. General Information Extended Product Type: Categories
Page 1 of 5 MS132-10 ABB contact for United States of America General Information Extended Product Type: Product ID: EAN: Catalog Description: Long Description: MS132-10 1SAM350000R1010 4013614400100 MS132-10
More informationNH DIN Dual Indication Fuse Links
Class of Operation gl/gg, 500V AC, 10 to 630 s Sizes 000 to 3 Standards/ Approvals: Description: Packaging: IEC 60269, VDE0636, DIN 43 620 1 to 4. A square bodied range of industrial fuse links for a wide
More informationDouble-deck PCB terminal strip; 2 solder pins, in line; 4x2-pole; pin spacing 10 mm / in
Double-deck PCB terminal strip; 2 solder pins, in line; 4x2-pole; pin spacing 10 mm / 0.394 in Item No.: 736-704 Double-deck PCB terminal strip; 2 solder pins, in line; 4x2-pole; pin spacing 10 mm / 0.394
More informationPower distribution. RiLine fuse elements. NH fuse-switch disconnectors, size 000. For mounting plate assembly
NH fuse-switch disconnectors, size 000 Version -pole, cable outlet at the top/bottom For the use of fuse inserts to EN 60 - Technical specifications to IEC/EN 60 947-, see chapter -5, page 6 see chapter
More informationOur Power Team High-Current, Rail-Mount Terminal Blocks for Conductors up to 185 mm 2 (350 kcmil)
Our Power Team High-Current, Rail-Mount Terminal Blocks for Conductors up to 185 mm 2 (50 kcmil) vibration-proof fast maintenance-free WAGO BENEFITS Using springs instead of screws is the key to WAGO s
More information, , PREPARATION - CONNECTION. Mounting:. On symmetrical EN rail or DIN 35 rail
87045 LIMOGES Cedex Telephone number: +33 (0)5 55 06 87 87 Fax: +33 (0)5 55 06 88 88 DX 3 4500 A / 6 ka CONTENTS PAGES 1. Description, use...1 2. Range...1 3. Overall dimensions...1 4. Preparation - Connection...1
More informationUL 508 Non-Fusible Disconnect Switches
UL 508 Non-Fused (M163 M803) The M-series Load Break Switch is the most compact industrial-grade switch on the market. Capable of making or breaking loads up to 600V (UL), it is suitable as a motor disconnect.
More informationRX 3 MCB 4500 A Phase + Neutral, neutral on left side
87045 LIMOGES Cedex Téléphone : 05 55 06 87 87 Télécopie : 05 55 06 88 88 RX 3 MCB 4500 A CONTENTS PAGE 1. Description, use... 1 2. Range... 1 3. Overall dimensions... 1 4. Preparation - Connection...
More information