Landscape Rakes LR2584, LR2596, LR3584 & LR3596

Transcription

1 Landscape Rakes LR2584, LR2596, LR3584 & LR3596 Model LR Model LR35! Read the Operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Cover photo may show optional equipment not supplied with standard unit. Copyright 2011 Printed 6/28/ M Operator s Manual

2 Important Safety Information Safety at All Times Look For The Safety Alert Symbol Safety Labels Introduction Application Using This Manual Owner Assistance Serial Number Section 1: Assembly and Setup Tractor Requirements LR25 Landscape Rake LR35 Landscape Rake Tractor Hook-Up Section 2: Optional Equipment Set-up...9 LR25 Single Gauge Wheel Assembly LR35 Series Gauge Wheel Assembly Dual Gauge Wheel Installation Gauge Wheel Assembly Grader Blade Installation Grader Blade with Dual Gauge Wheels Grader Blade without Dual Gauge Wheels Grader Blade Side Plate Assembly LR25 Support Stand (Accessory) LR25 Rake Angling Kit Section 3: Operating Instructions Operating Checklist Transporting Operating Instructions Section 4: Adjustments Angling and reversing Pitch Tilt Offset (LR35 Series Only) Dual Gauge Wheel (Optional) Flip Down Grader Blade (Optional) Single Gauge Wheel (Optional) Single Gauge Wheel Cylinder (Accessory)...17 Section 5: Maintenance & Lubrication..18 Maintenance Lubrication Dual Gauge Wheel Caster Gauge Wheel Caster Gauge Wheel Ratchet Jack Section 6: Options & Accessories Single Gauge Wheel Dual Gauge Wheel Flip Down Grader Blade Grader Blade Mounting Arm LR25 Hydraulic Rake Angling Kit (Accessory)...19 LR35 Hydraulic Frame Offset Kit (Accessory)...19 LR25 Support Stand (Accessory) Rear Blade Attachments (Accessory) Section 7: Specifications & Capacities..20 Section 8: Features and Benefits Section 9: Torque Values Chart Section 10: Warranty Copyright 2011 All rights Reserved Land Pride provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. Land Pride is a registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 6/28/11

3 Important Safety Information Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Safety at All Times Thoroughly read and understand the instructions given in this manual before operation. Refer to the Safety Label section, read all instructions noted on them. Do not allow anyone to operate this equipment who has not fully read and comprehended this manual and who has not been properly trained in the safe operation of the equipment.! Look For The Safety Alert Symbol The SAFETY ALERT SYMBOL indicates there is a potential hazard to personal safety involved and extra safety precaution must be taken. When you see this symbol, be alert and carefully read the message that follows it. In addition to design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in the operation, transport, maintenance and storage of equipment. Operator should be familiar with all functions of the unit. Operate implement from the driver s seat only. Make sure all guards and shields are in place and secured before operating implement. Do not leave tractor or implement unattended with engine running. Dismounting from a moving tractor could cause serious injury or death. Do not allow anyone to stand between the tractor and implement while backing up to the implement. Keep hands, feet, and clothing away from power-driven parts. Wear snug fitting clothing to avoid entanglement with moving parts. Watch out for wires, trees, etc., when raising implement. Make sure all persons are clear of working area. Turning tractor too tight may cause implement to ride up on wheels. This could result in injury or equipment damage. Do not carry passengers on implement at any time. Be Aware of Signal Words A Signal word designates a degree or level of hazard seriousness. The signal words are:! DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is limited to the most extreme situations, typically for machine components that, for functional purposes, cannot be guarded. For Your Protection Thoroughly read and understand the Safety Label section, read all instructions noted on them.! WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices.! CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Shutdown and Storage Lower machine to ground, put tractor in park, turn off engine, and remove the key. Detach and store implements in a area where children normally do not play. Secure implement by using blocks and supports. OFF REMOVE Parts Manual QR Locator The QR (Quick Reference) code on the front cover and to the left will take you to the Parts Manual for this equipment. Download the appropriate App on your smart phone, open the App, point your phone on the QR code and take a picture. Dealer QR Locator The QR code on the left will link you to available dealers for Land Pride products. Refer to Parts Manual QR Locator on this page for detailed instructions. 6/28/11 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 1

4 Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Use Safety Lights and Devices Slow moving tractors, selfpropelled equipment, and towed implements can create a hazard when driven on public roads. They are difficult to see, especially at night. Flashing warning lights and turn signals are recommended whenever driving on public roads. Transport Machinery Safely Comply with state and local laws. Maximum transport speed for implement is 20 mph. DO NOT EXCEED. Never travel at a speed which does not allow adequate control of steering and stopping. Some rough terrain require a slower speed. Sudden braking can cause a towed load to swerve and upset. Reduce speed if towed load is not equipped with brakes. Use the following maximum speed - tow load weight ratios as a guideline: 20 mph when weight is less than or equal to the weight of tractor. 10 mph when weight is double the weight of tractor. IMPORTANT: Do not tow a load that is more than double the weight of tractor. Use A Safety Chain A safety chain will help control drawn machinery should it separate from the tractor drawbar. Use a chain with the strength rating equal to or greater than the gross weight of the towed machinery. Attach the chain to the tractor drawbar support or other specified anchor location. Allow only enough slack in the chain to permit turning. Do not use safety chain for towing. Practice Safe Maintenance Understand procedure before doing work. Use proper tools and equipment, refer to Operator s Manual for additional information. Work in a clean dry area. Lower the implement to the ground, put tractor in park, turn off engine, and remove key before performing maintenance. Allow implement to cool completely. Do not grease or oil implement while it is in operation. Inspect all parts. Make sure parts are in good condition & installed properly. Remove buildup of grease, oil or debris. Remove all tools and unused parts from implement before operation. 2 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 6/28/11

5 Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Prepare for Emergencies Be prepared if a fire starts. Keep a first aid kit and fire extinguisher handy. Keep emergency numbers for doctor, ambulance, hospital and fire department near phone. Wear Protective Equipment Wear protective clothing and equipment appropriate for the job. Avoid loose fitting clothing. Prolonged exposure to loud noise can cause hearing impairment or hearing loss. Wear suitable hearing protection such as earmuffs or earplugs. Operating equipment safely requires the full attention of the operator. Avoid wearing radio headphones while operating machinery. 911 Keep Riders Off Machinery Riders obstruct the operator s view, they could be struck by foreign objects or thrown from the machine. Never allow children to operate equipment. Tire Safety Tire changing can be dangerous and should be preformed by trained personnel using the correct tools and equipment. When inflating tires, use a clip-on chuck and extension hose long enough to allow you to stand to one side and NOT in front of or over the tire assembly. Use a safety cage if available. When removing and installing wheels, use wheel handling equipment adequate for the weight involved. Avoid High Pressure Fluids Hazard Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic lines or performing work on the system. Make sure all hydraulic fluid connections are tight and all hydraulic hoses and lines are in good condition before applying pressure to the system. Use a piece of paper or cardboard, NOT BODY PARTS, to check for suspected leaks. Wear protective gloves and safety glasses or goggles when working with hydraulic systems. If an accident occurs, see a doctor immediately. Any fluid injected into the skin must be treated within a few hours or gangrene may result. 6/28/11 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 3

6 Important Safety Information Safety Labels Your Landscape Rake comes equipped with all safety labels in place. They were designed to help you safely operate your implement. Read and follow their directions. 1. Keep all safety labels clean and legible. 2. Replace all damaged or missing labels. To order new labels go to your nearest Land Pride dealer or visit our dealer locator at landpride.com. 3. Some new equipment installed during repair requires safety labels to be affixed to the replaced component as specified by Land Pride. When ordering new components make sure the correct safety labels are included in the request. 4. Refer to this section for proper label placement. To install new labels: a. Clean the area the label is to be placed. b. Spray soapy water on the surface where the label is to be placed. c. Peel backing from label. Press firmly onto the surface. d. Squeeze out air bubbles with the edge of a credit card. Model LR C Caution: Retaining Nut Model LR C Caution: Retaining Nut C Red Reflector (Back side of plate) C Amber Reflector (Front side of plate) (Left side only) 4 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 6/28/11

7 Introduction Introduction Land Pride welcomes you to the growing family of new product owners. This Landscape Rake has been designed with care and built by skilled workers using quality materials. Proper assembly, maintenance and safe operating practices will help you get years of satisfactory use from the machine. Application The LR25 and LR35 Series Landscape Rakes are designed and built by Land Pride to perform final soil surface preparation and reshaping soil and/or aggregate profile. LR25 Series rakes are offered with Cat. l 3-point hitch for mounting to compact tractors in the 25 hp to 50 hp. range. LR35 Series rakes are offered with Cat. l & ll 3-point hitch for mounting to tractors with 30 to 65 hp. capabilities. Both models are offered in 7 ft. and 8 ft. working widths with angling and reversing capabilities to meet specific finishing needs. Optional gauge wheel packages are available to enable a more consistent finish over uneven or undulating terrain. Also, an optional flip-down grader blade is offered to expedite material distribution and contouring tasks. These Land Pride Landscape Rakes are perfectly suited for use by landscapers, contractors, and rental yards. They have applications at housing and road construction projects, golf courses, terracing sites, run-off control projects, and reforestation sights. See Specifications & Capacities on page 20 and Features & Benefits on page 21 for additional information and performance enhancing options. Using This Manual This Operator s Manual is designed to help familiarize you with safety, assembly, operation, adjustments, troubleshooting, and maintenance. Read this manual and follow the recommendations to help ensure safe and efficient operation. The information contained within this manual was current at the time of printing. Some parts may change slightly to assure you of the best performance. To order a new Operator s or Parts Manual contact your authorized dealer. Manuals can also be downloaded, free-of-charge from our website at Terminology Right or Left as used in this manual is determined by facing forward in the direction the machine will operate while in use unless otherwise stated. Definitions IMPORTANT: A special point of information related to the following topic. Land Pride s intention is this information must be read & noted before continuing. NOTE: A special point of information that the operator should be aware of before continuing. Owner Assistance The Warranty Registration card should be filled out by the dealer at the time of purchase. This information is necessary to provide you with quality customer service. If customer service or repair parts are required contact a Land Pride dealer. A dealer has trained personnel, repair parts and equipment needed to service the rake. The parts on your Landscape Rake have been specially designed and should only be replaced with genuine Land Pride parts. Therefore, should your rake require replacement parts go to your Land Pride Dealer. Serial Number Model No. Serial No. For quick reference and prompt service, record model number and serial number in the spaces provided above and again on warranty page 23. Always provide model number and serial number when ordering parts and in all correspondences with your Land Pride dealer. Refer to Figure 1 for location of your serial number plate Serial Number Plate Location Figure 1 Further Assistance Your dealer wants you to be satisfied with your new Landscape Rake. If for any reason you do not understand any part of this manual or are not satisfied with the service received, the following actions are suggested: 1. Discuss the matter with your dealership service manager making sure he is aware of any problems you may have and that he has had the opportunity to assist you. 2. If you are still not satisfied, seek out the owner or general manager of the dealership, explain the problem and request assistance. 3. For further assistance write to: Land Pride Service Department 1525 East North Street P.O. Box 5060 Salina, Ks address lpservicedept@landpride.com 6/28/11 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 5

8 Section 1: Assembly and Setup Section 1: Assembly and Setup Tractor Requirements Tractor horse power and hitch category should be within the range noted below. Tractors outside the horsepower range must not be used. Tractor Horse Power Rating LR25 Series HP LR35 series HP Hitch Category LR25 Series Cat. l LR35 Series Cat. l & ll LR25 Landscape Rake Refer to Figure 1-1: 1. Attach upper hitch (#2) to frame assembly (#1) with 5/8" x 3 1/2" long bolts (#4) lockwashers (#5) and hex nuts (#6). 2. Position frame assembly (#1) upside down on stable supports. 3. Turn lower rake mount (#12) upside down and position it above the frame assembly pivot bolt (#14). Rotate lower rake mount such that it is parallel with the frame assembly and then carefully lower it onto pivot bolt (#14). Secure rake mount with spindle washer (#11) slotted hex nut (#10) and cotter pin (#9). 4. Install lower hitch pins (#3) with 5/8" hardware provided. 5. Position assembled unit upright and rotate to a forward position. Insert lock pin (#7) and secure with hair pin cotter (#8). 6. Attach rake to the tractor s 3-point hitch. See Tractor Hook-Up on page Some rake teeth may require repositioning due to crating. Loosen 3/8" lock nut (#13) and adjust/align these teeth to proper position. Retighten lock nuts to the correct torque.! CAUTION Always check to be sure that the slotted hex nut and cotter pin are in place to retain the rake before reversing the rake. If they are missing, the rake will fall off the frame while being rotated. LR25 Assembly Figure LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 6/28/11

9 Section 1: Assembly and Setup LR35 Landscape Rake Refer to Figure 1-2: 1. Uncrate rake assembly from shipping crate. 2. Position hitch frame (#1) in an upright stable position at rake height on suitable supports. 3. Attach frame assembly (#2) to the hitch frame with 1" x 6 1/2" GR5 bolt (#3) and lock nut (#4). 4. Insert pivot pin (#5) and secure with 3/16" x 1 3/4" long cotter pin (#6). 5. Assemble the male-female adjustable links (#13) and (#14) together and attach link assembly to frames (#1 & #2) with 1" x 2" clevis pins (#15) and 3/16" cotter pins (#16). Set link assembly to length with clevis pin (#17) and cotter pin (#18). 6. Position frame assembly (#2) upside down on stable supports. 7. Turn lower rake mount (#7) upside down and position it above the frame assembly pivot bolt (#20). Rotate lower rake mount such that it is parallel with the frame assembly and then carefully lower it onto pivot bolt (#20). Secure rake mount with spindle washer (#9) slotted hex nut (#8) and cotter pin (#10). 8. Position assembled unit upright and rotate frame assembly to a forward position. Insert lock pin (#11) and secure with hair pin cotter (#12). 9. Attach rake to the tractor s 3-point hitch. See Tractor Hook-Up on page Recheck all hardware for tightness. Torque all bolts to specifications as listed in Torque Values Chart for Common Bolt Sizes on page Some rake teeth may require repositioning due to crating. Loosen 3/8" lock nut (#19) and adjust / align these teeth to proper position. Retighten lock nuts to the correct torque.! CAUTION Always check to be sure that the slotted hex nut and cotter pin are in place to retain the rake before reversing the rake. If they are missing, the rake will fall off the frame while being rotated! LR35 Assembly Figure 1-2 6/28/11 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 7

10 Section 1: Assembly and Setup Tractor Hook-Up! DANGER Tractor hook-up to equipment is dangerous and can result in serious injury or death. Do not allow anyone to stand between the Landscape Rake and tractor during hook-up operations. Do not operate hydraulic 3-point lift controls while someone is directly behind the tractor or near the rake. Lower Hitch Hook-Up For LR25 Series Refer to Figure 1-3 & Figure 1-4: 1. Slowly back tractor up to the Landscape Rake while using the tractor s 3-point hydraulic control to align the lower hitch link holes with the implement s lower hitch pins. 2. Engage tractor park brake, shut tractor engine off and remove key before dismounting from tractor. 3. With tractor s lower hitch arms aligned and positioned, slide the lower hitch arm holes onto the hitch pins. Secure lower 3-point arms on the hitch pins with linch pins. 4. Ensure that the lower hitch arms are blocked to prevent excessive side movement. 5. Raise support stand all the way up and pin in transport position. Lower Hitch Hook-Up For LR35 Series Refer to Figure 1-3 & Figure 1-5: 1. Slowly back tractor up to the Landscape Rake while using the tractor s 3-point hydraulic control to align the lower hitch link holes with the hitch clevis holes. 2. Engage tractor park brake, shut tractor engine off and remove key before dismounting from tractor. 3. With tractor s lower hitch arms aligned and positioned in the clevises, insert hitch pins through the clevis lugs and lower hitch link holes. Be sure to use supplied bushings with a category 2 hitch. Secure hitch pins with linch pins. 4. Ensure that the lower hitch arms are blocked to prevent excessive side movement. 5. Raise support stand all the way up and pin in transport position. Top Center Hitch Hook-Up Refer to Figure 1-3: 1. Connect tractor s top center link to the upper hitch mounting hole using customer supplied 3/4 clevis pin, 1 bushing if Cat. II hitch and linch pin. Hitch Adjustments 1. Return to the tractor and slowly operate controls up and down to ensure that the drawbar, tires, and other equipment on the tractor do not contact the rake frame and teeth. Move or remove the drawbar if it interferes. 2. Manually adjust one of the two lower lift arms up or down to level the rake from left to right. 3. Manually adjust length of the top center link to level the rake from front to rear Cat. I Top Center Link Mounting Holes Hitch Pin Hitch Pin Quick Hitch Mounting Holes Linch Pin Retaining Pin Tractor 3-Point Hitch Figure 1-3 LR25 Series 3-Point Hitch Figure 1-4 Linch Pins Retaining Pin Cat. l Hook-up Cat. ll Hook-up with Bushings Support Stand LR35 Series 3-Point Hitch Figure 1-5 Support Stand Hitch Pin Linch Pin Hitch Pin Cat. I & II Top Center Link Mounting Holes 2552 Quick Hitch Mounting Holes LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 6/28/11

11 Section 2: Optional Equipment Set-up Section 2: Optional Equipment Set-up LR25 Single Gauge Wheel Assembly Refer to Figure 2-1: 1. Use gauge wheel mounting bracket (#1) as a pattern to locate and drill three 11/16 dia. holes in the rake frame back plate. 2. Attach mounting bracket (#1) with three 5/8-11 x 1 1/2 GR5 hex head cap screws, lock washers (#3) and hex nuts (#4). Tighten nuts to correct torque. 3. Attach gauge wheel arm (#5) to mounting bracket (#1) with 5/8-11 x 5 GR5 hex head cap screw (#6), flat washer (#7), 3 5/16 long tube (#8), flat washer (#9) and hex lock nut (#10). Tighten lock nut to correct torque. 4. Install 1 7/8 machine washer (#15) onto gauge wheel spindle (#14). 5. Insert gauge wheel spindle (#15) into gauge wheel arm (#5). 6. Secure gauge wheel with machine washer (#16) and 1/4 cotter pin (#17). Bend one or both legs of cotter pin to prevent cotter pin from falling out. Ratchet Jack Installation (standard) 1. Attach ratchet jack (#11) to mounting bracket (#1) and gauge wheel arm (#5) with clevis pins (#12). Secure pins with hair pin cotters (#13). Hydraulic Cylinder Installation (Optional) 1. Position hydraulic cylinder (#18) with ports on top as shown. Thread 90 degree elbows (#19) into the two ports and tighten. 2. Screw 125" long hydraulic hoses (#20) to the elbows and tighten. 3. Thread hydraulic couplings (couplings provided by customer) to the other end of hydraulic hoses and tighten. IMPORTANT: Assemble base end of cylinder to the front lug on mounting bracket (#1) as shown. 4. Attach hydraulic cylinder to the lugs on the gauge wheel with two 1" clevis pins (#21). Make sure hydraulic ports are positioned on top and cylinder base is located to the front as shown. 5. Secure clevis pins with pin clips (#22). 6. Connect hoses to the tractor's hydraulic system. LR25 Series Single Gauge Wheel Installation Figure 2-1 6/28/11 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 9

12 Section 2: Optional Equipment Set-up LR35 Series Gauge Wheel Assembly Refer to Figure 2-2: 1. Remove retainer plate (#4) from rake frame. 2. Attach mounting bracket (#1) and retainer plate (#4) with three new 5/8-11 x 1 1/2 GR5 hex head cap screws (#2) and lock washers (#3) as shown. Reuse existing hardware for lower bolt. Tighten bolts to correct torque. 3. Attach gauge wheel arm (#5) to mounting bracket (#1) with 5/8-11 x 5 GR5 hex head cap screw (#6), flat washer (#7), 3 5/16 long tube (#8), flat washer (#9) and hex lock nut (#10). Tighten lock nut to correct torque. 4. Install 1 7/8 machine washer (#15) onto gauge wheel spindle (#14). 5. Insert gauge wheel spindle (#14) into gauge wheel arm (#5). 6. Secure gauge wheel with 1 7/8 machine washer (#16) and 1/4 cotter pin (#17). Bend one or both legs of cotter pin to prevent cotter pin from falling out. Ratchet Jack Installation (standard) 1. Attach ratchet jack (#11) to mounting bracket (#1) and gauge wheel arm (#5) with clevis pins (#12). Secure pins with hair pin cotters (#13). Hydraulic Cylinder Installation (Optional) 1. Position hydraulic cylinder (#18) with ports on top as shown. Thread 90 degree elbows (#19) into the two ports and tighten. 2. Screw 125" long hydraulic hoses (#20) to the elbows and tighten. 3. Thread hydraulic couplings (couplings provided by customer) to the other end of hydraulic hoses and tighten. IMPORTANT: Assemble base end of cylinder to the front lug on mounting bracket (#1) as shown. 4. Attach hydraulic cylinder to the lugs on the gauge wheel with two 1" clevis pins (#21). Make sure hydraulic ports are positioned on top and cylinder base is located to the front as shown. 5. Secure clevis pins with pin clips (#22). 6. Connect hoses to the tractor's hydraulic system. LR35 Series Single Gauge Wheel Installation Figure LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 6/28/11

13 Section 2: Optional Equipment Set-up Dual Gauge Wheel Installation Refer to Figure 2-3: Gauge Wheel Assembly 1. Attach gauge wheel arm (#1) to the right hand side of rake mount (#7) with six 3/8 x 2 3/4 hex head bolts (#8), 3/8 lockwashers (#9), and 3/8 hex nuts (#10) as shown. Tighten to proper torque. 2. Insert two bushings (#5) into gauge wheel arm (#1) as shown. 3. Insert yoke with tire assembly (#2) through 1/2 spacer (#3), 1 spacer #4, spindles (#5), and three 1 Spacers (#4) as shown. Secure with wire retaining pin (#6). 4. Repeat steps 1 through 3 to assemble gauge wheel on the left hand side of the rake Gauge Wheel Assembly Right Hand Assembly Shown Figure 2-3 Grader Blade Installation Grader Blade with Dual Gauge Wheels Refer to Figure 2-4: NOTE: The grader blade can be supported from the dual gauge wheel support arms as shown in Figure 2-4. See Figure 2-5 on page 12 when mounting grader blade without gauge wheels. 1. Refer to Dual Gauge Wheel Installation steps 1-4 on this page to assemble dual gauge wheels. 2. Attach blade lock handle (#3) to the right and left hand Gauge Wheel Arms with 1/2 x 3 GR5 hex bolts (#2), lock washers (#14), and hex nuts (#15) as shown. Tighten to proper torque. 3. Insert pin (#1) through top hole of both gauge wheel arms. Secure with attached hair pin (#9) as shown. 4. Attach both the right end and left end of the grader blade (#11) to gauge wheel arms with 3/4 x 2 3/4 GR5 hex bolts (#12) and locknuts (#13) as shown. Do not torque locknut (#13). 5. Refer to Grader Blade Side Plate Assembly on page 12 for attaching side plates to both ends of the grader blade Grader Blade Assembly with Gauge Wheel Right Hand Side Shown Figure 2-4 6/28/11 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 11

14 Section 2: Optional Equipment Set-up Grader Blade without Dual Gauge Wheels Refer to Figure 2-5: 1. Attach blade support arms (#16) to the right and left side of rake mount (#20) with 3/8 x 2 3/4 GR5 hex bolts (#17), 3/8 lockwashers (#18), and 3/8 hex nuts (#19) (six bolts per support arm). Tighten to proper torque. 2. Attach blade lock handle (#3) to the right and left blade support arms with 1/2 x 3 GR5 hex bolts (#2), lock washers (#14), and hex nuts (#15) as shown. Tighten to proper torque. 3. Insert pin (#1) through the top hole in both blade support arms. Secure with hair pin (#9). 4. Attach the right and left end of grader blade (#11) to the blade support arms with 3/4 x 2 1/2 GR5 hex bolts (#12) and locknuts (#13). Do not torque locknuts (#13). Grader Blade Side Plate Assembly Refer to Figure 2-4 and Figure 2-5: 1. Attach two hex coupler nuts (#8) with flat washer (#6) to side plates (#7) by inserting 7/16 x 1 GR5 hex bolts (#4) complete with lock washers (#5), and flat washers (#6) through the bottom and top holes as shown. Do not torque until step Insert pivot pin on side plates (#7) through the tubes located on the back side of grader blade (#11). Make certain coupler nuts (#8) are positioned behind the grader blade. Secure pivot pins with hair pins (#9) 3. Adjust hex coupler nuts (#8) against back side of grader blade and tighten bolts (#4) to proper torque Grader Blade Assembly without Gauge Wheel Right Hand Side Shown Figure 2-5 LR25 Support Stand (Accessory) Refer to Figure 2-6: LR25 Series Landscape Rakes with serial number and higher are factory supplied with a support stand. You may purchase an accessory support stand from your nearest Land Pride dealer if the serial number on your rake is or below. For additional information, see LR25 Support Stand (Accessory) on page 19. Retaining Pin Support Stand LR25 Support Stand (Accessory) Figure LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 6/28/11

15 Section 2: Optional Equipment Set-up LR25 Rake Angling Kit Refer to Figure 3-1 on page 16: 1. Set rake angle at 90 to the main frame and secure with lock pin (#1). IMPORTANT: For the angling kit to work properly, the lock pin must be removed after installing this kit. Refer to Figure 2-7: 2. Locate and drill on both sides of the rake frame two 9/16 dia. holes 5/8 up from the bottom and 31 1/16 from the back plate as shown. 3. Locate and drill on both sides of the rake frame another set of two 9/16 dia. holes only this time 3 3/8 up from the bottom and 31 1/16 from the back plate as shown. 4. Attach front cylinder mount (#13) to the left side of the rake frame with two 1/2-13 x 7 GR5 hex head bolts (#14), lock washers (#7) and hex nuts (#8). Tighten nuts to the correct torque. 5. Position rear cylinder mount (#5) over the rake frame with the back two holes 3 5/16 from the back plate as shown. 6. Using the rear cylinder mount as a template, locate and drill four 9/16 dia. holes in the rake frame. 7. Attach rear cylinder mount (#5) to the rake frame with two 1/2-13 x 6 GR5 hex head bolts (#6), lock washers (#7) and hex nuts (#8). Tighten nuts to the correct torque. 8. Insert spindle bushings (#2) into the cylinder pivot bracket (#1) as shown. 9. Attach cylinder pivot bracket (#1) to the rear cylinder mount (#5) with 1 flat washer (#3) and secure with 3/16 cotter pin (#4). Be sure to bend one or more legs of the cotter pin to keep it from falling out. 10. Position hydraulic cylinder (#15) with ports on top as shown. Thread 90 degree elbows (#16) into the two ports and tighten. 11. Screw 84" long hydraulic hoses (#17) into the elbows and tighten. 12. Thread hydraulic couplings (couplings provided by customer) to the other end of hydraulic hoses and tighten. IMPORTANT: Attach base end of cylinder to the front cylinder mounting bracket (#13) as shown. 13. Attach hydraulic cylinder to the cylinder mounting brackets with two 1" clevis pins (#18). Make sure hydraulic ports are positioned on top and cylinder base is located to the front as shown. 14. Secure clevis pins with cotter pins (#19). 15. Connect hoses to the tractor's hydraulic system. 16. Start tractor and extend cylinder rod to one-half its stroke length. Back Plate Back of Rake LR25 Series Rake Angling Kit Figure 2-7 Front of Rake Right Side of Rake Frame 17. Shut tractor off, set park brake and remove switch key before continuing. 18. Insert cylinder pivot mount (#9) into cylinder pivot bracket (#1). Place base end of mounting bracket over the rake channel frame. 19. Using the pivot mounting bracket (#9) as a template, locate and drill four 7/16 dia. holes as shown. 20. Insert cylinder pivot mount (#9) into cylinder pivot bracket (#1). Attach base end of pivot mount to the channel frame with two 3/8-16 x 4 1/2 GR5 hex head bolts (#10), lockwashers (#11) and hex nuts (#12). Tighten nuts to correct torque. 21. Secure pivot mount (#9) to cylinder pivot bracket (#1) with 1 flat washer (#3) and 3/16 cotter pin (#4). Be sure to bend one or more legs of the cotter pin to keep it from falling out. 22. Remove lock pin and store for safe keeping. 6/28/11 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 13

16 Section 3: Operating Instructions Section 3: Operating Instructions Operating Checklist Hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training involved in the operation, transport, maintenance and storage of the blade. Therefore, it is absolutely essential that no one operates the Landscape Rake without first having read, fully understood and become totally familiar with the Operator s Manual. Make sure the operator has paid particular attention to: Important Safety Information, pages 1 to 3 Section 1: Assembly and Setup, page 9 Section 2: Optional Equipment Set-up, page 9 Section 3: Operating Instructions, page 14 Section 4: Adjustments, page 16 Section 5: Maintenance & Lubrication, page 18 Operating Checklist Check Reference Check 3-point Hook-up procedure. Be sure all pins have been installed and are secured. Page 8 All rake adjustments have been made and pins have been installed and are secured. Page 16 The operator has read and understands how to operate the rake. Page 14 The Landscape Rake has been lubricated as required. Page 18 Check the rake initially and periodically for loose bolts & pins, See Torque Values Chart. Page 22 Make the following inspections after attaching the Landscape Rake to the tractor: 1. Inspect tractor safety equipment to make sure it is in good working condition. 2. Carefully raise and lower the implement to ensure that the drawbar, tires, and other equipment on the tractor do not contact the frame and moldboard. 3. Carefully pivot rake fully clockwise and offset rake such that the rake teeth closest to the tractor are in line with the tractor tire. Raise and lower implement to ensure tractor tires and tractor do not contact the rake. 4. Carefully pivot rake fully counterclockwise and offset rake such that the rake teeth closest to the tractor is in line with the tractor tire. Raise and lower implement to ensure tractor tires and tractor do not contact the rake. Transporting! CAUTION When traveling on public roads at night or during the day, use accessory lights and devices for adequate warning to operators of other vehicles. Comply with all federal, state and local laws. 1. When traveling on roadways, transport in such a way that faster moving vehicles may pass you safely. 2. Leave enough clearance on both sides of the rake when traveling straight or making turns to keep the blade from contacting obstacles such as buildings, trees or fences. 3. Slow down when traveling over rough or hilly terrain. Operating Instructions! WARNING Do not use the rake for pulling fence posts, stumps, etc., lifting objects, carry objects or towing other equipment. Any of the above can result in rake damage, serious bodily injury or death.! DANGER Never carry a person on the rake. A person can fall and be ran over by the rake or tractor causing serious injury or death. By now you should have thoroughly read your Operator s Manual and properly installed your Land Pride Landscape Rake to your tractor. Before you begin raking you should visually survey the work site to make sure it is safe and free of foreign obstacles. Also make certain that all irrigation heads, utility outlets, and other obstacles are properly marked. Please stop and do the above checks and preparations if you have not yet done so before you begin to rake. This is a must for your safety and for the safety of others. Now that you are properly briefed, your landscape rake is properly installed, and you have properly checked out your work site, it is time to begin raking. When transporting or travelling to and from work sites, make sure that the rake is in the fully raised position and not in contact with the ground. Select a safe speed and transport to your work site in such a manner that faster moving vehicles can pass you safely. A slow moving vehicle sign should be employed if you are using a public road or right-of way. 14 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 6/28/11

17 Section 3: Operating Instructions Once you have safely arrived at your work site, lower your rake with the 3-point hitch control lever so that the rake is just barely off of the ground. Lock the tractor brake to prevent rolling, shut off the tractor, and remove the ignition key before dismounting. Make the necessary angle, pitch, and gauge wheel adjustments to the rake to achieve desired results. Changing the rake angle to left or right will distribute extraneous and oversized material in furrows to the left or right. Changing the pitch angle of the rake by adjusting the top link in or out to tilt the bottom in toward the tractor will result in more aggressive action and vice-versa. Setting the proper height on the adjustable gauge wheels will enable a consistent raking that is less affected by uneven ground conditions encountered by the tractor wheels. After you have made your initial adjustments and settings, get back on the tractor and make a gear and engine rpm selection that will enable a ground speed safe and suitable for your ground and operating conditions. Lower the rake into operating position and begin working. Achieving the desired affect may require additional adjustments. With a little practice you should begin to consistently achieve the desired results. Always keep safety uppermost in your mind and remember that before dismounting the tractor you must always set the park brake, lower your 3-point attachment to the ground, turn off the tractor and remove the ignition key. If you must park on a hillside you should always chock the tractor wheels for an extra measure of safety. See Product Specifications on page 20 and Features and Benefits on page 21 for additional information on performance enhancing options. 6/28/11 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 15

18 Section 4: Adjustments Section 4: Adjustments Angling and reversing LR25 Series Refer to Figure 3-1: The rake can be angled up to 45 to the right or left in 15 increments each way. Remove lock pin (#1) and angle the rake to the desired position. Replace pin (#1) and secure with hair pin cotter (#2). The rake can be adjusted for pushing material backwards. Remove the lock pin (#1) and rotate rake 180 from the forward position. Replace the lock pin (#1) and secure with hair pin cotter (#2). Tilt LR25 Series Adjusting one of the tractor s lower 3-point link arms up or down to tilt one end of the rake lower than the other. LR35 Series Refer to Figure 3-2: Remove pin (#1) and tilting one end of the rake up or down to a maximum of 30 in 15 increments Rake Angling (LR25 Series shown) Figure LR35 Series Refer to Figure 3-1: The LR35 has the same lock pin as the LR25 and is adjusted in the same fashion. The rake can be angled up to 60 right or left in 15 increments each way. Remove lock pin (#1) and angle rake to the desired position. Replace lock pin and secure with hair pin cotter (#2). The rake can be adjusted for pushing material backwards and angled up to 60 left or right in 30 increments each way. Remove lock pin (#1) and rotate rake 180 from the forward position. Replace pin (#1) once rake is angled to the desired position. Secure lock pin with hair pin cotter (#2). Pitch The pitch of the rake can be adjusted by lengthening or shortening the top center 3-point link on the tractor to tilt the bottom of the rake teeth. Tilting the teeth in toward the tractor will result in more aggressive action and away from the tractor will be less aggressive. LR35 Rake Tilt Figure 3-2 Offset (LR35 Series Only) The LR35 rake may be offset manually or hydraulically 45 left or right. Dual Gauge Wheel (Optional) Refer to Figure 3-3: Pull clip pin (#1) at the top of the gauge wheel shaft and remove shaft and wheel assembly from the gauge wheel arm (#4). Place desired number of spacers (#2) on the shaft and replace shaft in gauge wheel arm. Place remaining spacers (#3) on shaft above gauge wheel arm and reattach clip pin (#1) Dual Gauge Wheel Figure LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 6/28/11

19 Section 4: Adjustments Flip Down Grader Blade (Optional) Refer to Figure 3-4: The grader blade can be stored in the up position when not in use and lowered when needed. 1. Carefully pivot blade upward until it contacts the blade lock handles (#1). A lock pin (#2) should be placed in the lower hole to insure that the grader blade remains securely in the raised position. 2. Lower blade by removing the lock pin from the lower hole and replace in upper hole. 3. Pull blade lock handle (#1) to allow grader blade to flip down. NOTE: The grader blade can only be attached if the rake is equipped with dual gauge wheels Grader Blade Lock Up Position Figure 3-4 Single Gauge Wheel (Optional) Refer to Figure 3-5: The height of the gauge wheel is determined by adjusting the ratchet jack. The gauge wheel will adjust up or down by positioning the lever on the ratchet jack. Single Gauge Wheel Cylinder (Accessory) A 3 1/2 x 8 hydraulic cylinder can be purchased from Land Pride to raise and lower the gauge wheel with tractor hydraulic control levers Single Gauge Wheel Adjustment Figure 3-5 6/28/11 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 17

20 Section 5: Maintenance & Lubrication Section 5: Maintenance & Lubrication Maintenance Proper servicing and adjustment is the key to the long life of any implement. With careful and systematic inspection, you can avoid costly maintenance, time and repair. After using your Landscape Rake for several hours, check all bolts to be sure they are tight. Replace any worn, damaged or illegible safety labels by obtaining new labels from your Land Pride Dealer. Lubrication Lubrication Legend Multi-purpose spray lube Multi-purpose grease lube Multi-purpose oil lube 50 hrs Intervals in hours at which lubrication is required 25 Hours Dual Gauge Wheel Caster Grease the gauge wheel zerk every 25 hours when the rake is in use Type of Lubrication: Multi-Purpose Quantity = Until grease begins to emerge. As Required Gauge Wheel Caster Lubricate daily when the blade is in use and before storing Type of Lubrication: Multi-Purpose Quantity = 2-4 pumps As Required Gauge Wheel Ratchet Jack Type of Lubrication: Multi-Purpose Quantity = 2-4 pumps LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 6/28/11

21 Section 6: Options & Accessories Section 6: Options & Accessories Single Gauge Wheel Kit Bundles A & 35 BLADE & RAKE SINGLE GW A & 35 SERIES GAUGE WHEEL CYLINDER ACCESSORY Dual Gauge Wheel Note: Arm of Dual Gauge Wheel provides a mount to support a grader blade. Kit Bundles A DUAL GAUGE WHEELS-Narrow A DUAL GAUGE WHEELS-Wide Flip Down Grader Blade Note: Grader blade assembly is complete with side plates only. Grader Blade Mounting Arms must be purchased separately if Dual Gauge Wheels are not mounted on the Landscape rake. Kit Bundles A FLIP DOWN GRADER BLADE ASSY A ' GRADER BLADE ASY A ' GRADER BLADE ASY A ' GRADER BLADE ASY Grader Blade Mounting Arm Note: Two Grader Blade Mounting Arms are required to support a Flip Down Grader Blade A GRADER BLADE MOUNT LESS DUAL GAUGE WHEEL LR25 Hydraulic Rake Angling Kit (Accessory) Kit Bundle A SERIES RAKE ANGLING KIT (S/N ) LR35 Hydraulic Frame Offset Kit (Accessory) Kit Bundle A SERIES 3 1/2 x 8 CYLINDER, HOSE & FITTINGS LR25 Support Stand (Accessory) LR25 Series Landscape Rakes with serial number and higher are factory supplied with a support stand. You may purchase an accessory support stand from your nearest Land Pride dealer if the serial number on your rake is or below. Assembly instructions are included with the stand. Kit Bundle A RB/LR25 SUPPORT STAND Rear Blade Attachments (Accessory) Available for Landscape Rakes with S/N and higher. The rake assembly can be removed from the main frame and a RB25 or RB35 Series rear blade assembly can be attached to the frame to give your Land Pride Rake versatility. Be careful not to overstress the rear blade while back-filling as load forces on the blade and frame increase while backing-up. Kit Bundles A & 35 SERIES: 72 BLADE ASSEMBLY A SERIES: 84 REAR BLADE ASSEMBLY A SERIES: 96 REAR BLADE ASSEMBLY A SERIES: 84 REAR BLADE ASSEMBLY A SERIES: 96 REAR BLADE ASSEMBLY 6/28/11 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 19

22 Section 7: Specifications & Capacities Section 7: Specifications & Capacities LR25 & LR35 Series LR2584 LR2596 LR3584 LR3596 Rake Width Approximate Weight (lbs.) Horsepower Rating Rake Height 16 1/2 16 1/2 Hitch Type Parking Stand Individual Replaceable Teeth Cat. l Fits Land Pride Quick Hitch Standard Standard Cat. l & ll Fits Land Pride Quick Hitch Number of Teeth Teeth Size Teeth Spacing Teeth Material 5/16 x 1 Wide 2 Centers High Carbon Spring Steel Angle/Position 7 Forward / 5 Reverse 45 o right or left 9 Forward / 5 Reverse 60 o right or left Tilt N/A 5 positions to 30 degrees Gauge Wheel Options Single Gauge Wheel 8 x 4 x 4.8 Dual Narrow Width Wheels 13 x 4 x 6 Dual Wide Width Wheels 13 x 6 1/2 x 6 Flip Down Grader Blade Option Flip Down Self Supporting Grader Blade with Blade-up Locking Handles and locking pins. Hydraulic Angle Option Up to 45 degrees right or left N/A Manual/Hydraulic Offset Option N/A Up to 45 degrees right or left Rear Blade Attachment Accessory Available Available Available Available LR25 Series Landscape Rakes LR35 Series Landscape Rakes 20 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 6/28/11

23 Section 8: Features and Benefits Section 8: Features and Benefits LR25 Series Features Working widths 84, 96 HP Range Fits Land Pride Quick-Hitch Angle 7 forward positions and 5 reverse positions Optional hydraulic angle cylinder HP Benefits Allows for quick and easy one person hook-up. Vary amount of material to move. Change the rake angle on the go from the tractor seat. 16 Rake height Allows for moving a great deal of material. Rake teeth support channel 5/16 x 1" High carbon spring steel teeth Individually replaceable teeth Retractable Parking Stand Single or dual gauge wheels (optional) Flip-down grader blade and end plates (optional) Blade adaptable Warranty Features Design with channel support. This design supports the rake teeth better than competitor models. Prevents teeth entanglement and keeps attachment hardware from working loose. Sized to eliminates premature bending and tooth breakage. Constructed of materials that have memory to spring back to shape. Makes replacement easy and quick. Keeps the frame off the ground and makes hook-up easier. Depth control. Working widths 84, 96 Tractor HP Range Cat. l & ll Fits Land Pride Quick-Hitch Frame offsets 45 degrees manually or hydraulically Angle 9 forward positions and 5 reverse positions Allows rake to be used for leveling by being able to scrape and drag material. Adds versatility. Replace Rake elements with moldboard. One year parts & labor HP LR35 Series Fits a wider variety of tractors. Benefits Allows for quick and easy one person hook-up. Easily cover one tractor tire track. Optional hydraulic provided control from the tractor seat. Vary the amount of material being moved. 16 1/2 Rake height Can move a great deal of material. Rake teeth support channel 5/16 x 1" High carbon spring steel teeth Individually replaceable teeth Retractable Parking Stand Rear Blade adaptable Single or dual gauge wheels (optional) Flip-down grader blade and side plates (optional) Warranty Design with channel support. This design supports the rake teeth better than competitor models. Prevents teeth entanglement and keeps attachment hardware from working loose. Sized to eliminates premature bending and tooth breakage. Constructed of materials that have memory to spring back to shape. Quick and easy replacement. Keeps the frame off the ground and makes hook-up easier. Get more out of a rake investment. Provide better depth control. Enables the rake to perform light blading duties and can be flipped up when not in use. One year parts & labor. 6/28/11 LR2584, LR2596, LR3584 & LR3596 Landscape Rakes M 21