TECHNICAL BULLETIN. 1 st CATEGORY RACING CARS FORMULA VEE TECHNICAL REGULATIONS REFERENCE: RATIONALE: To clarify the Formula Vee Technical Regulations
|
|
- Maurice Benson
- 5 years ago
- Views:
Transcription
1 Bulletin Number: B15/006 Implementation Date: 26/03/2015 TECHNICAL BULLETIN 1 st CATEGORY RACING CARS FORMULA VEE TECHNICAL REGULATIONS REFERENCE: RATIONALE: To clarify the Formula Vee Technical Regulations ACTION: To amend the Formula Vee Technical Regulations as follows: PREAMBLE For Formula Vee s Log Booked after July 2014; in addition to being issued with a CAMS log book, to become eligible for competition, the a Formula Vee shall must be issued with a Certificate of Compliance from a State Formula Vee Association. 2.6 ENGINE: (v) Crankshaft:... The crankshaft may be ground and the case may be machined to accommodate the use of the standard VW oversize/undersize crankshaft bearings, provided the crankshaft location is not changed. It may also be machined to permit installation of camshaft bearings. Lightening of the crankshaft is permitted. Metal removed shall must be confined to the circumference surface of the crankshaft webs.
2 (vii) Flywheel and clutch assembly: For 1200cc engines machining of all flywheel surfaces is permitted. The flywheel shallmust comply with the minimum weight specified in art. 3, Weights and Dimensions. The use of any flywheel, as used on a Type1 or Type 3 VW originally fitted with a six volt or 12 volt electrical system, is permitted: For 1600cc engines lightening of the flywheel is permitted by machining of the clutch plate and pressure plate contact surfaces and the back face only. The lightened flywheel shall respect the dimensions in the diagram below: (ix) Camshaft followers: Machining of the camshaft contact face only of the camshaft followers is permitted. Modified contact face must not be concave. Camshaft followers may have a single centralised lubrication hole of a maximum 1mm diameter as supplied by the manufacturer. (x) Cylinders, Pistons, Rings and Gudgeon Pins: Removal of metal from pistons and gudgeon pins for balancing purposes is permitted. Metal removal must be confined to the inner surfaces of the piston so that the skirt perimeter is not modified in any way; For 1200cc engines each piston and gudgeon pin may be lightened but shall comply with the minimum weight specified in article 3, Weights and Dimensions. Metal removal shall be confined to the inner surfaces of the piston only. that the skirt perimeter is not modified in any way. A piston ring
3 functioning in the normal manner shall be fitted in each groove of the piston. Each piston and barrel shall comply with the requirements of Non Genuine Parts, except that: (a) The minimum width of the top and second ring groove shall be 2.00mm. (b) The minimum width of the oil ring groove shall be 4.00mm. (c) The minimum distance from the top of the gudgeon pin bore to the face of the piston shall be 27.90mm. For 1600cc engines pistons and gudgeon pins may be lightened. Pistons shall be cast aluminium alloy with a steel insert and the profile of the bottom of the piston skirt shall be as manufactured. Piston and gudgeon pin shall comply with the minimum weight and dimensions specified in art. 3, Weights and Dimensions. A piston ring, functioning in the normal manner, shall be fitted in each groove of the piston. Each piston gudgeon pin circlip can be replaced by a Teflon button. Each Piston shall meet the requirements of Non Genuine Parts except that they do not require the cast in steel plate. Machining the spigot faces of barrels to obtain deck height is permitted. (xii) Valve Train: For 1600 and 1200 engines Valves shallmust conform with Articles 1.1, 3 and 4 with the exception that they may be manufactured from any ferrous material 2.7 ENGINE ANCILLARIES: (i) Carburettor: For 1200cc engines:.. (f) The throttle shaft is not to be modified. The minimum thickness of the throttle shaft is 4.7mm. (iii) Inlet Manifold: (b) The aircleaner shall have a horizontal interior surface located no higher than 10mm above the uppermost edge of the carburettor air inlet. The interior of the air cleaner, to a minimum diameter of 70mm and maximum of 150mm centred on the carburettor air inlet and to a minimum height of 40mm and maximum of 80mm above the horizontal surface, shall be free space. The use of any aircleaner which is less than the specified envelope is permitted. The aircleaner shall have a horizontal interior surface located at the uppermost edge of the carburettor air inlet.
4 (vi) Cooling System: (c) Modification of the fan housing is permitted in order to provide for an airtight passage for any member of the safety cage structure and an orifice (to the specified dimensions) for external oil cooler hoses. Each bracket is permitted to be fixed to the fan housing so long as its attachment forms an airtight seal. (d) It is permitted to attach brackets directly to the fan housing provided that the bracket attachment forms an airtight seal. (vii) Distributor: (a) The distributor is free provided it retains the original drive and location and mechanical high tension current distribution. Each standard Bosch or replica point may be replaced with an electronic replacement point set ignition module. The replacement set ignition module shall be installed totally within the distributor without requiring any modification to the distributor. When a replacement point ignition module is installed it shall provide a fixed dwell angle at all engine RPM. A list of part numbers currently approved by the FVAA National Technical Committee will be available on the FVAA website. (b) The advance curve is free 2.8 TRANSMISSION: (a) For 1200 engines the use of any standard VW Type 1, 2 or 3 component which can be fitted without modification to itself or any other component is permitted. Any of the following standard VW gear ratios is permitted: 2.9 CHASSIS AND SAFETY CAGE STRUCTURES: (b) Configuration: (vi) The main roll bar shall be located immediately behind the cockpit with the plane of the main hoop within +/- 10 of perpendicular to the longitudinal centreline of the vehicle. With the driver seated in the normal position the hoop shall: 3.3 ENGINE: (i) Crankcase: Cam follower bore face to crankcase joint face: 31mm maximum
5 (ii) Flywheel weight: 1200cc engine: 5.4kg minimum 1600cc engine: - With either E, E, F or Crankshafts: 7.0kg minimum - With an Aftermarket Counter Weighted Crankshaft: 5.4kg minimum Clutch pressure plate weight: cc engine: 2.5kg minimum cc engine: 3.25kg minimum (iv) Pistons/Cylinders/Connecting Rods: Cylinder bore: 1200cc engine: 77.21mm maximum 1600cc engine: 85.70mm maximum Piston top to cylinder seal face: 1200cc engine: 1.0mm minimum Refer to table below 1600cc engine: 1.0mm minimum Refer to table below (v) Cylinder Head: 1200cc engine Intake port diameter at flange face: 29.0mm maximum Exhaust port diameter at flange face: 33.0mm maximum Combustion chamber volume: 38cc minimum Valve guide length: 62.5mm ± 2.5mm Cylinder head secondary cut OD: 77.0 ± 0.5mm Cylinder head secondary cut depth: 1.5mm Outside diameter of inlet and exhaust port inserts: Inlet: 36.5mm Exhaust: 33.5mm 3.4 ENGINE ANCILLARIES: (i) Carburettor: 1200cc engine Venturi Dimensions: OD: Length: Maximum Diameter of Base of Carburettor throttle body taken in any given direction: 1600cc engine: As Standard 27.8 ± 0.5mm 26.0 ± 0.5mm 28.1mm
6 5. AUTHORISED PARTS The following parts can be from any source, provided their use does not result in the unauthorised modification of any other component: a threaded fasteners (but not wheel mounting bolts) h ignition coil o starter motor b brake lines i 6v or 12v batteries p swivel foot valve adjusters c fuel lines j shock absorbers q disc brake calipers d spark plugs k fuel filters r disc rotor/hub assemblies e master cylinders l ignition s fan belt points f carburettor jets m washers t distributor and venturi (1200 only) g push rod tubes n piston rings u valve push rods v External Oil Coolers and Oil Cooling Fans Y w Flywheel x Aftermarket Counter Weighted Crankshaft Ignition Modules: Compufire: part no Pertronix Ignitor I (not II or III) part no s: 1847A, D & D A list of part numbers currently approved by the FVAA National Technical Committee is available on the FVAA website. END
TECHNICAL BULLETIN. Formula Vee Technical Regulations. REFERENCE:
Bulletin Number: B15/038 Implementation Date: 01/01/2016 TECHNICAL BULLETIN Formula Vee Technical Regulations REFERENCE: http://docs.cams.com.au/manual/race/ra14-formula-vee-2015-1.pdf RATIONALE: To update
More information2019 CAMS MANUAL OF MOTOR SPORT
2019 CAMS MANUAL OF MOTOR SPORT SPECIFICATIONS OF AUTOMOBILES 1st Category Racing Cars Formula Vee Regulations CONFEDERATION OF AUSTRALIAN MOTOR SPORT WWW.CAMS.COM.AU Modified Article Date of Application
More informationMONOPOSTO RACING Class Specification Formula Vee REVISED March 2008
MONOPOSTO RACING Class Specification Formula Vee REVISED March 2008 VINTAGE FORMULA VEE (PRE-1970) These rules describe and specify Formula Vee racing cars as they raced in the 1969 racing season. This
More information45.06 Fuel Refer Chapter 22 Fuel, as run, to comply with tests under chapter 22.01
CHAPTER 45 PARILLA LEOPARD 125cc and PARILLA LEOPARD X30 125cc Preamble It is expected that this class will continue to evolve during its early life and the promoters of the class reserve the right to
More informationCOMER SW80 TECHNICAL SPECIFICATIONS
COMER SW80 TECHNICAL SPECIFICATIONS Comer SW80 Toowoomba % LV Tech Spec 2017 Preamble: The following are the Technical Specifications for the COMER SW80 engine, as approved by the Australian Karting Association.
More informationMinistock Rule Update
Ministock Rule Update 08-08-17 Following on from the positive feedback received under the Consultation process in late 2016, the Board have agreed to the following rule updates to be made on the Ministocks.
More informationCOMER SW80 TECHNICAL SPECIFICATIONS
VERSION 3 / 2013 UPDATED AUGUST 20 th, 2013 DOCUMENT UPDATE SCHEDULE It is certified that the updates listed below have been approved by the Australian Karting Association and have been incorporated into
More informationWorld Formula TECH MANUAL
World Formula TECH MANUAL Section 1 General Rules 1. Only stock Briggs & Stratton World Formula Model # 124435-8101 will be used in this class except as provided in this Tech manual. All parts will be
More informationCOMER SW80 TECHNICAL SPECIFICATIONS
UPDATED JANUARY 2012 Preamble: SW 1.01 SW 1.02 The following are the Technical Specifications for the engine, as approved by the Australian Karting Association. This engine is approved for use in the CADET
More information5TH CATEGORY - HISTORIC RACING. GROUP Nc APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Nc APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More information5TH CATEGORY - HISTORIC RACING. GROUP Sc APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Sc APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationPARILLA LEOPARD X TECHNICAL SPECIFICATIONS
PARILLA LEOPARD X30 125 VERSION 7 / 2013 UPDATED JULY 16 th, 2013 DOCUMENT UPDATE SCHEDULE It is certified that the updates listed below have been approved by the Australian Karting Association and have
More informationENGINE. Manufacturer IAMEs.p.a. Category. Homologation Period. Pages 16. Model, Type SIGNATURE AND STAMP OF AKA SIGNATURE AND STAMP OF APPLICANT
1 ENGINE Manufacturer IAMEs.p.a. Category Make Model, Type PARILLA Leopard X30 125cc RL - TaG - AUS Homologation Period Pages 16 This homologation sheet reproduces description, illustrations and dimensions
More informationTHE WOLSELEY "VIPER" AERO ENGINE. (Hispano-Suiza W.4.A*)
13 THE WOLSELEY "VIPER" AERO ENGINE. (Hispano-Suiza W.4.A*) General description. The engine referred to in this article is the Hispano-Suiza 180 hp W.4.A* Aero Engine, as made by Wolseley Motors Ltd. The
More informationPARILLA LEOPARD RL 125 TECHNICAL SPECIFICATIONS
PARILLA LEOPARD RL 125 VERSION 4 / 2012 UPDATED September 6 th, 2012 DOCUMENT UPDATE SCHEDULE It is certified that the updates listed below have been approved by the Australian Karting Association and
More information1 Informations générales : 1.1 Créateur SUBARU Karting. 1.3 Marque et modèle. 1.4 Cylindrée. 1.5 Photos FICHE HOMOLOGATION MOTEUR KART SUBARU KX-21
FICHE HOMOLOGATION MOTEUR KART SUBARU KX-21 MOTOR KART SUBARU KX-21 HOMOLOGATION FORM 1 Informations générales : 1.1 Créateur SUBARU Karting OF COURSE SARL 1.2 Fabriquant 1.3 Marque et modèle FUJI HEAVY
More information#100 TO #199 SPORTSMAN 1600 LIGHT BUGGY TECHNICAL SPECIFICATIONS
#100 TO #199 SPORTSMAN 1600 LIGHT BUGGY TECHNICAL SPECIFICATIONS DEFINITION 1600 Light Buggy is a one-person, limited 4-wheel car using Volkswagen type 1 stock components with a 1585 cc engine. All parts
More informationTORC SERIES COMPETITION RULES FOR SPORTSMAN 1600 BUGGY
TORC SERIES COMPETITION RULES FOR SPORTSMAN 1600 BUGGY DEFINED AS- A limited 4-wheel vehicle utilizing a type-1, 1600 c.c. Volkswagen air-cooled engine with one person in the vehicle. Division rules supersede
More informationBriggs & Stratton. World Formula & Modified World Formula. Tech Manual
Briggs & Stratton World Formula & Modified World Formula Tech Manual First Issued: May 22, 2007 Updated: January 2017 Jerry Mostek QMA Tech 2012 Quarter Midgets of America, Inc. WORLD FORMULA CLAIM RULE
More information2019 CAMS MANUAL OF MOTOR SPORT
2019 CAMS MANUAL OF MOTOR SPORT RALLY/ROAD CLASSIC RALLY CARS CONFEDERATION OF AUSTRALIAN MOTOR SPORT WWW.CAMS.COM.AU Modified Article Date of Application Date of Publication Art. 5.2 Suspension 01/01/2019
More informationREGULATION OF YAMAHA SUNDAY RACE RACE 2017
1. ENGINE SPECIFICATIONS 1.1. Engine Type 4 Stroke Single Cyl 4 Stroke Single Cyl 4 Stroke Single Cyl 1.1.1. Displacement Up to 150cc Up to 150cc Up to 150cc 1.1.2. Engine Layout vertical vertical vertical
More information2017 TAG 125cc Stock Moto Specifications and Tech Procedures
2017 TAG 125cc Stock Moto Specifications and Tech Procedures Spirit and intent The following rules are applied in order to provide fair and equal competition within the class. The specifications and limitations
More information11.5 BOMBARDIER ROTAX FR125 MAX SPECIFICATIONS
11.5 BOMBARDIER ROTAX FR125 MAX SPECIFICATIONS Preamble: The following are the Technical Specifications for the Rotax FR125 Max engine, as approved by AIDKA. Unless otherwise specified, the engines must
More informationModified Article Date of Application Date of Publication
2018 CAMS MANUAL OF MOTOR SPORT SPECIFICATIONS OF AUTOMOBILES 5th Category Historic Cars Vehicle Eligibility Historic Specials CONFEDERATION OF AUSTRALIAN MOTOR SPORT WWW.CAMS.COM.AU Modified Article Date
More information5TH CATEGORY - HISTORIC RACING. GROUP Nc APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Nc APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationMotorcycle parts compatibility on ebay.co.uk
Motorcycle parts compatibility on ebay.co.uk Review the full list of categories and subcategories in which you can list motorcycle and scooter parts. Last updated: 10 August 2016 Motorcycle Parts (10063)
More information5TH CATEGORY - HISTORIC RACING. GROUP Nb APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Nb APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationENGINE 108H. Manufacturer. TORINI MOTOR CO., LTD. Make. TORINI Model. TRE220 UPDATE (to TC250) Validity of the homologation 6 years Number of pages 31
ENGINE Manufacturer TORINI MOTOR CO., LTD. Make TORINI Model TRE220 UPDATE (to TC250) Validity of the homologation 6 years Number of pages 31 This Homologation Form reproduces descriptions, illustrations
More information5TH CATEGORY - HISTORIC RACING. GROUP Sb APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Sb APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More information6 cylinder turbocharged diesel engines for industrial applications
Perkins 2800 Models 2806C-E16 WORKSHOP MANUAL 6 cylinder turbocharged diesel engines for industrial applications Publication TSD3450E, Issue 1 Proprietary information of Perkins Engines Company Limited,
More information5TH CATEGORY - HISTORIC RACING. GROUP Nc APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Nc APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationNATIONAL HOMOLOGATION FORM KARTING ENGINE
NATIONAL HOMOLOGATION FORM KARTING ENGINE Manufacturer TORINI MOTOR CO., LTD. Make TORINI Model CLUBMAXX 210 (TC210) Validity of the homologation 6 years Number of pages 34 Homologation N This Homologation
More informationMONOPOSTO RACING Class Specification Formula Super Vee [Air Cooled & Water Cooled] April 2017
MONOPOSTO RACING Class Specification Formula Super Vee [Air Cooled & Water Cooled] April 2017 I. Definition FORMULA SUPER VEE [AIR COOLED] A formula for single-seat, open wheel racing cars based on standard
More informationBRP-ROTAX FR 125 MAX TECHNICAL SPECIFICATIONS
BRP-ROTAX FR 125 MAX VERSION 1 / 2012 UPDATED JANUARY 1 st, 2012 DOCUMENT UPDATE SCHEDULE It is certified that the updates listed below have been approved by the Australian Karting Association and have
More informationNATIONAL HOMOLOGATION FORM KARTING ENGINE
NATIONAL HOMOLOGATION FORM KARTING ENGINE Manufacturer TORINI MOTOR CO., LTD. Make TORINI Model TC250 (PREVIOUSLY TRE220) UPDATE Validity of the homologation 6 years Number of pages 35 This Homologation
More informationSOHC ENGINE MECHANICAL
SECTION 1B SOHC ENGINE MECHANICAL CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed
More informationSection 10 Mini Stocks
Section 10 Mini Stocks 10.1 DEFINITION. 10.1.1 The word stock will mean unaltered as originally factory produced and installed for make. All Cars and trucks will be stock unless otherwise specified within
More informationNatural Bridge Speedway Official 2016 Rules Sportsman
Natural Bridge Speedway Official 2016 Rules Sportsman www.nbspeedway.com 540-451-2943 Official 2016 Sportsman Rules Natural Bridge Speedway Page 2 Rulebook Disclaimer The rules and/or regulations set forth
More informationMONOPOSTO RACING Class Specification Formula Atlantic REVISED March 2008
MONOPOSTO RACING Class Specification Formula Atlantic REVISED March 2008 FORMULA ATLANTIC I. Engines A. Displacement -- over 1100 cc and below or equal to 1600 cc. Cars with rotary piston engines covered
More informationHONDA GX200 SPARE PARTS
HONDA GX200 SPARE PARTS Copyright 2011 L&S Engineers Ltd. PAGE 1 Honda GX200 - Cylinder Head & Camshaft Page 2 BPR6ES 1.35 95723-08060-00 1.10 12391-ZE1-003 2.35 90047-ZE1-000 1.70 12251-ZL0-003 6.65 94301-10160
More informationTKM BT82 Engine Homologation Fiche
TKM BT82 Engine Homologation Fiche BT820394 Effective January 1, 2013 Created 03/1994 Incorporating all Extensions & Amendments to Date Note: All amendments/changes from last year to this year are highlighted
More information5TH CATEGORY - HISTORIC RACING. GROUP Nb APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Nb APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More information5TH CATEGORY - HISTORIC RACING. GROUP Nb APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Nb APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationNATIONAL HOMOLOGATION FORM
NATIONAL HOMOLOGATION FORM Homologation N ENGINE Manufacturer BRIGGS & STRATTON Make ANIMAL Model 124332 Validity of the homologation 6 years Number of pages 27 This Homologation Form reproduces descriptions,
More informationYAMAHA KT100J SERIES TECHNICAL SPECIFICATIONS
YAMAHA KT100J SERIES VERSION 2 / 2012 UPDATED FEBRUARY 1 st, 2012 DOCUMENT UPDATE SCHEDULE It is certified that the updates listed below have been approved by the Australian Karting Association and have
More informationCANADIAN AUTOMOBILE SPORT CLUBS ONTARIO REGION. Appendix O, Section A - Formula 1200
CANADIAN AUTOMOBILE SPORT CLUBS ONTARIO REGION Appendix O, Section A - Formula 1200 Effective April 10, 2018 This page intentionally left blank All material in this document is strictly the copyright of
More informationAUSTRALIAN WORLD RULES FOR BRP-ROTAX FR 125 MAX TECHNICAL SPECIFICATIONS
AUSTRALIAN WORLD RULES FOR BRP-ROTAX FR 125 MAX VERSION 4 / 2012 UPDATED APRIL 23 rd, 2012 It is certified that the updates listed below have been approved by the Australian Karting Association and have
More informationSECTION 1 - CHASSIS 1.1 CHASSIS FRAME
5TH CATEGORY - HISTORIC RACING GROUP Nb APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationHonda GX 160 Technical Regulations
Honda GX 160 Technical Regulations GENERAL The scrutineer will pay special attention to ensure that the fi nish of all components match those of the standard unit and reserves the right to compare any
More informationAUSTRALIAN WORLD RULES FOR BRP-ROTAX FR 125 MAX
AUSTRALIAN WORLD RULES FOR BRP-ROTAX FR 125 MAX VERSION 8 / 2013 UPDATED JUNE 7 th, 2013 DOCUMENT UPDATE SCHEDULE It is certified that the updates listed below have been approved by the Australian Karting
More informationFastener Tightening Specifications Specification
2008 G6 Applies to: 3.5L Report a problem with this article Fastener Tightening s A/C Compressor Bracket Bolt Camshaft Position Actuator Assembly Bolt 16 Y 12 lb ft Camshaft Position Actuator Magnet Bolt
More informationSPECIFICATIONS OF AUTOMOBILES
2012 CAMS Manual of Motor Sport SPECIFICATIONS OF AUTOMOBILES All vehicles in races and other speed events must comply with the General Requirements of Automobiles (see General Requirements for Cars and
More informationAUSTRALIAN WORLD RULES FOR BRP-ROTAX FR 125 MAX DD2
AUSTRALIAN WORLD RULES FOR BRP-ROTAX FR 125 MAX DD2 VERSION 6 / 2013 UPDATED JANUARY 3 rd, 2013 DOCUMENT UPDATE SCHEDULE It is certified that the updates listed below have been approved by the Australian
More informationYAMAHA KT100S SERIES TECHNICAL SPECIFICATIONS
YAMAHA KT100S SERIES VERSION 5 / 2013 UPDATED AUGUST 20 th, 2013 DOCUMENT UPDATE SCHEDULE It is certified that the updates listed below have been approved by the Australian Karting Association and have
More informationWORLD OF MOTORSPORT ZA
WORLD OF MOTORSPORT ZA P.O. Box 12387, Brakpan North, 1545 18 Main Reef Rd Brakpan (on the premises of Rock Raceway) Tel: 011-740 1206 / 740 8315 Fax: 086 508 2388 email: womza@telkomsa.net www.womzasa.co.za
More informationNATIONAL HOMOLOGATION FORM KARTING ENGINE
NATIONAL HOMOLOGATION FORM KARTING ENGINE Manufacturer BRIGGS & STRATTON Make BRIGGS & STRATTON Model 206-124332 Validity of the homologation 6 years Number of pages 25 This Homologation Form reproduces
More informationNote: Registration does not imply or guarantee use in a class
1 Note: Registration does not imply or guarantee use in a class or classes. Application for use in a class or classes must be applied for after Homologation and Registration approvals ENGINE Manufacturer
More informationPetrol Engine 13hp PARTS BOOKLET MODEL: LF13
Petrol Engine hp PARTS BOOKLET MODEL: LF Index Crankcase Assembly Crankcase Cover Assembly Cylinder Head & Cylinder Head Cover Assembly Crankshaft, Piston, Connecting & Balancing Shaft Combination of Camshaft
More informationAUSTRALIAN WORLD RULES FOR BRP-ROTAX FR 125 MAX
AUSTRALIAN WORLD RULES FOR BRP-ROTAX FR 125 MAX VERSION 7 / 2013 UPDATED JANUARY 24 th, 2013 DOCUMENT UPDATE SCHEDULE It is certified that the updates listed below have been approved by the Australian
More informationWKA 2010 MANUFACTURER S CUP TAG SERIES REGULATIONS
WKA 2010 MANUFACTURER S CUP TAG SERIES REGULATIONS Contact information and updates can be found at www.ovka.com The following regulations are guidelines ONLY. Please refer to 2010 WKA Technical Manual
More informationTECHNICAL FORM SEAT LEON CUP RACER MK3 1. GENERAL. Homologation N. Extension N. Model: LEON CUP RACER MK3. Make: SEAT SPORT
Model: LEON CUP TECHNICAL FORM Certification valid as from: 26 MARCH 215 SEAT 1. GENERAL 11. MANUFACTURER SEAT 12. MODEL AND TYPE a) Model and type LEON CUP b) Typical chassis number VSSMK35F4XSSPXXXX
More informationGROUP Sc 5TH CATEGORY - HISTORIC RACING APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Sc APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationCanadian Karting Honda Technical Regulations
Canadian Karting Honda Technical Regulations To be read and applied in conjunction with: Canadian Karting Regulations Book 1, Sporting Regulations and Book 2 Technical Regulations Effective January 1,
More informationSE120R SCREAMIN' EAGLE PRO RACE-USE CRATE ENGINE
-J007 REV. 00-09-08 SE0R SCREAMIN' EAGLE PRO RACE-USE CRATE ENGINE GENERAL Kit Number 90- Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
More informationCAMS 5TH CATEGORY - HISTORIC RACING. GROUP Sb APPROVED VEHICLE SPECIFICATION
CAMS 5TH CATEGORY - HISTORIC RACING GROUP Sb APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued
More information1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder
ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION
More information2018 Junior Sprint Rules
2018 KidSprint Engine Rules Briggs World Formula 2018B All parts must be Briggs & Stratton factory production parts unless otherwise noted in these rules. No machining, polishing or alteration of any parts
More informationModel Year: 1980 Manufacturer: Model: Honda CB750K. Schematic: AIR CLEANER. Description: 1980 Honda CB750K AIR CLEANER
Manufacturer: Model: Schematic: Description: Honda CB750K AIR CLEANER 1980 Honda CB750K AIR CLEANER Manufacturer: Model: Schematic: Description: Honda CB750K BATTERY 1980 Honda CB750K BATTERY Schematic:
More informationNATIONAL HOMOLOGATION FORM KARTING ENGINE X30 SUPER - TAG
NATIONAL HOMOLOGATION FORM KARTING ENGINE X30 SUPER - TaG Manufacturer IAME S.P.A - ZINGONIA Make IAME Model X30 SUPER - TAG Validity of the homologation 6 years Number of pages 51 This Homologation Form
More information5TH CATEGORY - HISTORIC RACING. GROUP Sb APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Sb APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More information2018 CAMS MANUAL OF MOTOR SPORT
2018 CAMS MANUAL OF MOTOR SPORT SPECIFICATIONS OF AUTOMOBILES 2nd Category Sports Cars Group 2B Porsche 944 CONFEDERATION OF AUSTRALIAN MOTOR SPORT WWW.CAMS.COM.AU Modified Article Date of Application
More information2008 Formula First Rules
2008 Formula First Rules (Effective 1/1/08) These rules use a slightly different numbering system from the SCCA GCR. Rules are grouped by subject matter. Principal points in each subject use two numbers
More informationRULE BOOK DISCLAIMER DIXIE SPECIAL EVENT PONY RULES
RULE BOOK DISCLAIMER The rules and/or regulations set forth herein are designed to provide for the orderly conduct of racing events and to establish minimum acceptable requirements for such events. These
More informationNOVICE 1, 2 & JUNIOR 1 & 2 DIVISIONS
NOVICE 1, 2 & JUNIOR 1 & 2 DIVISIONS 708 BRIGGS LOCAL OPTION 206 Briggs & Stratton (B&S) Model 124332 Type 8201 only. The intent of this class is to provide a sealed, simple-to-operate, ultra dependable
More informationLocal Option 206 Rules Manual Section 1 General Rules 1. Only stock Briggs & Stratton LO206 # engine will be allowed in this class.
Local Option 206 Rules Manual Section 1 General Rules 1. Only stock Briggs & Stratton LO206 # 124332-8201engine will be allowed in this class. o All parts will be stock unaltered Briggs & Stratton Animal
More informationWORLD OF MOTORSPORT ZA P.O. BOX 12387, BRAKPAN NORTH, 1545 TEL: / FAX: LITRE HOTROD PINTO RULES
2014 2015 2LITRE HOTROD PINTO RULES Introduction: Competitor age restriction: Only competitors over the age of 14 years old are permitted, to enter into this class. 2.0 Litre Ford Pinto SOHC engines are
More informationILLUSTRATED PARTS BOOK 196cc Rear Tine Tiller PRTT196E.1 PRTT196E.2
ILLUSTRATED PARTS BOOK 196cc Rear Tine Tiller PRTT196E.1 PRTT196E.2 MAT Engine Technologies, LLC, REV. 20180928 Table of Contents Upper Handle Assembly... 2 Forward Controls... 3-4 Rear Controls... 5-6
More information100cc REEDJET USA TaG
100cc REEDJET USA TaG FEATURES Cylinder Volume 100 cm³ max Bore 48.20 mm Max. theoretical bore 48.53 mm Stroke 54.05 mm max Cooling system Air Inlet system Reed valve Number of carbs 1 Tillotson Carburettor
More informationKARTSPORT NEW ZEALAND MANUAL SECTION N SPECIFICATIONS RULE N10 - VORTEX KIWI MINI ROK. Issue published and effective
KARTSPORT NEW ZEALAND MANUAL SECTION N SPECIFICATIONS RULE N10 - VORTEX KIWI MINI ROK Issue 2018-1 published and effective 10-4-18 Rule N10 VORTEX KIWI MINI ROK N10.1 GENERAL SPECIFICATIONS 10.1.1 These
More informationMotorsport South Africa
Motorsport South Africa SOUTH AFRICAN KARTING COMMISSION HOMOLOGATION SCHEDULE MAXTERINO MX-60 Version 1 2017-01-25 MSA Ref. Manufacturer MAXTER S.R.L. Distributor Ed Murray Racing cc Model Maxterino Period
More informationPage 1 of 9 303-01C Engine 6.0L Diesel 2004 F-Super Duty 250-550/Excursion DESCRIPTION AND OPERATION Procedure revision date: 08/06/2003 Engine Printable View Engine Description The 6.0L diesel engine
More informationSF90 Pmi Shifter 90cc Go Kart (VIN PREFIX LBFM)
Page 1 of 23 Product Information Baja Web > Product Information > Parts Lists > GOKART > SF90 Pmi Shifter 90cc Go Kart (VIN PREFIX LBFM) SF90 Pmi Shifter 90cc Go Kart (VIN PREFIX LBFM) SF90 Pmi Shifter
More information9.1 Technical Specification (within the engine seal) for ROTAX kart engines 125 Junior MAX (15 kw) 125 MAX (21 kw). 125 Junior MAX 125 MAX
9.1 Technical Specification (within the engine seal) for ROTAX kart engines 125 Junior MAX (15 kw) 125 MAX (21 kw). Squish gap 1.1 1.2 Combustion chamber insert 2.1 2.2 125 Junior MAX 125 MAX 1,20 mm -
More informationChainsaw Emak S.p.A.
Chainsaw - Engine Meccanografico RE 005145 C/C Postale 11178423 Partita IVA 00130010358 Codice Fiscale 00130010358 1 / 12 Meccanografico RE 005145 C/C Postale 11178423 Partita IVA 00130010358 Codice Fiscale
More information2019 CAMS MANUAL OF MOTOR SPORT
2019 CAMS MANUAL OF MOTOR SPORT SPECIFICATIONS OF AUTOMOBILES 1st Category Racing Cars Formula Ford 1600 - Technical Regulations CONFEDERATION OF AUSTRALIAN MOTOR SPORT WWW.CAMS.COM.AU Modified Article
More informationV8 Engine Differences
V8 Engine Differences With Dart engines becoming scarcer, you may need to use an engine from a V8 Saloon so it pays to know the key differences between the two. The Edward Turner designed 2.5 litre V8
More information1 REGULATIONS AND SPECIFICATIONS FOR THE 2015 SHORT CIRCUIT MOTORCYCLE 150 SENIOR CHAMPIONSHIP MSA WESTERN CAPE MOTORSPORT CIRCULAR WC 20/
1 REGULATIONS AND SPECIFICATIONS FOR THE 2015 SHORT CIRCUIT MOTORCYCLE 150 SENIOR CHAMPIONSHIP MSA WESTERN CAPE MOTORSPORT CIRCULAR WC 20/2015 1. CONTROLLERS Will be the Western Province Short Circuit
More informationCHARGER 2017 RULES & REGULATIONS Revised 1/22/17
CHARGER 2017 RULES & REGULATIONS Revised 1/22/17 IMPORTANT NOTE: Applications for NASCAR License may be obtained from the Pit Steward at the sign -in-window or at the speedway office during regular business
More information2013 Senoia Raceway Rulebook
2013 Senoia Raceway Rulebook E-mail tech questions to: johnnywalls31@yahoo.com BOMBER RULES BODY 1. All bodies must be stock steel bodies. No fiberglass or aluminum body panels allowed. Fenders and quarter
More information2006 WORLD CHALLENGE SEASON
2006 WORLD CHALLENGE SEASON VEHICLE MANUFACTURER: YEAR & MODEL: Cadillac (2004-) CTS-V This specifications form was developed by SCCA Pro Racing and will be used by the Series Technical Administrator to
More informationUnit: mm (in) ITEM STANDARD LIMIT IN. 33 (1.3) EX.
Model: DR650SEL0 E-03, 24, 28, 33 Date: July 16, 2009 SERVICE DATA VALVE + GUIDE Valve diam. Valve clearance (when engine is cold) Valve guide to valve stem clearance Valve stem deflection Valve guide
More informationDRAFT VTS. Approved for Racing
DRAFT VTS Approved for Racing Vehicle Manufacturer: Audi Year and Model: 2009-2013 R8 This draft of the listed vehicle s VTS is posted with the specifications that we currently have for the vehicle. If
More informationSECTION D Engine 6.0L Diesel
303-01D-i Engine 6.0L Diesel 303-01D-i SECTION 303-01D Engine 6.0L Diesel CONTENTS PAGE DESCRIPTION AND OPERATION Engine... 303-01D-2 303-01D-2 Engine 6.0L Diesel 303-01D-2 DESCRIPTION AND OPERATION Engine
More informationThunder Bomber 2018 GENERAL
Thunder Bomber 2018 GENERAL - Tech man has right to check this every week. 1. No nitrous or traction control. 2. After 3 times of refusing to tear down - you will be disqualified from competing in this
More informationMODEL NUMBER AND IDENTIFICATION. Pag. 5 CHARACTERISTICS CHARACTERISTIC POWER, TORQUE AND SPECIFIC CONSUMPTION CURVES
MODEL NUMBER AND IDENTIFICATION CHARACTERISTICS CHARACTERISTIC POWER, TORQUE AND SPECIFIC CONSUMPTION CURVES MAINTENANCE - RECOMMENDED OIL TYPE - REFILLING POSSIBLE CAUSES AND TROUBLE SHOOTING OVERALL
More informationREAL FEDERACIÓN ESPAÑOLA DE AUTOMOVILISMO
Make: SEAT Sport TECHNICAL FORM TCN2 Certification valid as from: 08 APRIL 2016 Homologation form only valid for cars in Compliance with the SAFETY CAGE CERTIFICATE HES4441013 1. GENERAL 101. MANUFACTURER
More information5TH CATEGORY - HISTORIC RACING. GROUP Nc APPROVED VEHICLE SPECIFICATION
5TH CATEGORY - HISTORIC RACING GROUP Nc APPROVED VEHICLE SPECIFICATION This form details the approved specifications of individual vehicle models in the 5th Category Historic car group. To be issued with
More informationCEV BUCKLER 2012 TECHNICAL RULES Moto3
CEV BUCKLER 2012 TECHNICAL RULES Moto3 Moto3 TECHNICAL REGULATIONS CEV 2012 Contents 1. Engine 2. Inlet & Fuel System 3. Exhaust System 4. Transmission 5. Ignition, Electronics & Data-Logging 6. Chassis
More informationHonda GX 160 Technical Regulations
Honda GX 160 Technical Regulations 1. GENERAL The scrutineer will pay special attention to ensure that the finish of all components match those of the standard unit and reserves the right to compare any
More information2016 QUEENSLAND GEMINI RACING VEHICLE REGULATIONS
2016 QUEENSLAND GEMINI RACING VEHICLE REGULATIONS 2016 Queensland Gemini Racing Vehicle Regulations Page 2 of 8 Document ID: 2016 Queensland Gemini Racing Vehicle Regulations - QSC15.7350 Date of Implementation:
More information