Fuel Tank Fitment Instructions Tusk/Rally Raid Products/Seat Concepts kit Husqvarna 701 Enduro

Size: px
Start display at page:

Download "Fuel Tank Fitment Instructions Tusk/Rally Raid Products/Seat Concepts kit Husqvarna 701 Enduro"

Transcription

1 Fuel Tank Fitment Instructions Tusk/Rally Raid Products/Seat Concepts kit Husqvarna 701 Enduro

2 Part # , , , Thank you for purchasing the Tusk/Rally Raid Products fuel tank/seat kit. This kit will allow you to install the Rally Raid Products KTM 690 Fuel tanks and shrouds to the Husqvarna 701 Enduro. When purchasing the Tusk Conversion Kit you should have also received these other products as well. 1. Rally Raid Products KTM 690 Fuel Tank Kit (white or natural) 2. Rally Raid Products KTM 690 Shrouds 3. Seat Concepts Seat (Standard or tall) These instructions will replace the Rally Raid Products instructions you will not need to use the instructions that are in the Rally Raid Products kit. Thoroughly read these instructions from start to finish before you begin. If you do not feel confident or have the necessary tools to complete this install it is recommended to take it to a qualified mechanic.

3 Fig.1 Fig.2 Fig.3 Fig.4 Fig.5 Fig.6 Fig.7 Fig.8 Fig.11 Fig.9 Fig.13 Fig.10 Fig.12

4

5

6

7 Instructions 1. Remove the seat and unplug the battery. Remove all of the side plastics from the bike. 2. Air box removal. Remove electrical plug from rear of air box. Undo the intake boot clamp (the one nearest the throttle body) and remove the four M6 screws from the air box. 2 front and 2 rear. 3. Lift up the rear of the air box and slide out. Once the air box is removed put clean tissues or cloth into the intake of injector assembly to prevent debris from entering the engine. 4. Follow the hose from the charcoal canister to the left side of the throttle body. Disconnect and install the supplied vacuum cap on the brass nipple, re-using the clamp to secure. 5. Take the vent hose from the fuel cap and disconnect from canister and vent to atmosphere, trim as required. Make sure the open end is in place where it will not get blocked with mud. Cutting at an angle can help prevent blocking. Air box plug Remove canister and bracket 6. Remove canister from bike. 7. Remove solenoid from bike. Unplug solenoid here

8 8. Jump the 2 pins on the plug that went into the solenoid with a 1000 Ohm 1/4 watt resistor. If you have dielectric grease, place in terminals before installing the resistor. 9. Tape up resistor plug with electrical tape to seal from water/dirt and zip tie in a secure location. 10. Undo both M6 screws and remove the rectifier from RH frame guard, keep the screws for later use. Remove both screws that hold the plastic shroud to the frame and discard the plastic cover and both screws. 11. Cut the cable ties that hold the rectifier wiring to frame and disconnect large brown connector plug on LH side of frame (may be very tight). Disconnect other connector to rectifier on RH side of frame and earth connector and remove rectifier and connected wiring loom from bike. Rectifier Install resistor here 12. Remove RH rear engine hanger lower torx screw and fit rectifier bracket special bolt Rally Raid Products (#31). Use Loctite when fitting back into frame. Remove rear horn bracket M6 screw then fit new rectifier bracket with M6 screws and Loctite securely. RRP #31 Special Bolt Horn bracket screw Remove plastic shroud

9 Horn bracket 13. Install Rally Raid Products rectifier bracket #28 re-using the two OEM bolts. M6 OEM bolts 14. Refit rectifier in place using both original screws then feed wiring through frame and reconnect both plugs as shown. Re-fit earth connector with screw on frame. Rectifier Bracket # Feed brown connector through gap between Y piece and plug in. Brown plug M6 Screws Rectifier

10 INSTALLATION INSTRUCTIONS AND INFORMATION 16. Upper Tank Mount Fitment. Locate Rally Raid Products tank mounts and hardware. #14,15, 41. Install tank mount as shown but do not tighten bolts, leave them loose enough that you can adjust the mount by hand. Make sure that the flat side of the tank mount is facing towards the rear of bike. Repeat for opposite side. Flat side facing rear 17. Lower Tank Mount Fitment. Locate the Rally Raid Products lower tank mount #13 and install in the location shown. Use Loctite on this bolt. Repeat for opposite side. Lower Tank Mount 18. Rubber Bumper installation. Remove the jnut that is in the frame tab and install the rubber bumpers. Item #7 in the Tusk Kit. Repeat step for opposite side. Install rubber bumper here Upper Tank Mount

11 19. Fuel Tank Fitment. From the Tusk Kit Locate items #1,2,5,6. Cap screws and spacers. Install the lower cap screw and spacer first and tighten finger tight. Place the spacer between the tank and the tank mount. Fig.2 M8 x 75mm Cap Fig.6 13mm Spacer Fig.5 6mm Spacer 20. Next install the upper cap screw and spacer, the upper tank mount will most likely need to be adjusted on the frame in order for the tank to line up with the mount. Adjust for optimal fit and tighten both cap screws. If you are satisfied with the fit, tighten the three screws on the tank mount. Remove tanks for now. Repeats steps for opposite side. Fig.1 M8 x 70mm Cap Screw

12 21. Fuel Tank Adapter Install. Empty as much fuel as you can from the OEM tank before starting. Remove rear wheel and rear mud flap in order to access fuel pump. Remove mud flap screws 22. Remove the four M5 screws that connect the fuel pump housing to the bottom of the tank. (fuel may leak out as housing is lowered). Release clips here 23. Gently lower pump assembly and unclip black housing from pump by releasing both clips on each side of pump. Fuel pump housing Housing Cap Fuel pump

13 24. Using a 5/16 drill bit, drill a hole in the bottom of the housing centering it the best you can. It does not need to be exact and does not need to line up with anything. Make sure all of the plastic is cleaned up and removed from the housing to avoid any unwanted debris from entering the fuel system. Re-install the housing onto the fuel pump and make sure the housing securely clips into the black housing cap. Drill 5/16 Hole 25. The Rally Raid Products adapter and banjo fitting will not be used. Rally Raid adapter and banjo fitting 26. Locate the supplied Tusk Adapter Plate and the Rally Raid Products O-ring. With the O- ring in place on the adapter plate, install to the bottom of the fuel pump housing using the (4) M5 x.8 x 30mm hex bolts and the (4) M5 flat washers supplied in the Tusk Kit. The 90 degree brass elbow should be pointing towards the right hand side of the bike. Make sure you tighten in a cross pattern so that the housing will seat and seal correctly to the tank. Tighten bolts. Tusk Adapter Plate Rally Raid O-ring 90 deg NPT elbow pointing right M5 bolts and washers (4)

14 27. Locate the fuel line assembly supplied in the Rally Raid Products kit. Study the fuel line diagram in the image to the right. To rear OEM tank To LH tank To RH tank Note: It is vitally important that the fuel line to the left tank is installed correctly. Improper placement could cause contact with header pipe and a potential fire hazard. Rally Raid quick disconnect 28. Route the fuel line as shown and use the supplied zip ties to secure the fuel lines to the desired location. To RH tank Note: Extra Tusk Fuel line is supplied if the Rally Raid Products fuel line runs short. 29. Reinstall both tanks. When refitting both tanks pass the fuel lines through the plastic P clips on the inside of the tank. Use the fuel line clamps supplied in the Rally Raid Products Kit. Trim the fuel line for optimal fit. Reinstall all tank hardware and tighten. To LH tank P Clip

15 30. Reduced crankcase breather tank. Install the Rally Raid Products Reduced crankcase breather tank as shown in the image to the right. Reduced Crank Case Breather Cut notch here 31. It is required to cut a small notch in the plastic clamp that holds the tank to the frame. Plug in all the hoses in the same fashion as the OEM crank case breather tank. 32. Next you will reinstall air box assembly, when installing the boot to the throttle body be sure that it fits correctly. It is critical that there are no leaks around the boot.

16 33. Trimming of right hand side plastic. You will need to trim a notch in the right hand side plastic to allow for fuel line clearance. This can easily be done with a body saw, jig saw or small grinder. After cutting be sure to file or sand the edge smooth. 34. Reinstall all plastics onto the bike. Right hand side plastic Cut notch here 35. Install your new Seat Concepts Seat, it will install same as the OEM seat. 36. This concludes the installation of the Rally Raid Products Fuel Tank and Seat kit for the Husky 701 Enduro.

17 PROCEDURE FOR FILLING TANKS It is advisable when filling both front tanks and rear OEM tank to isolate the front tanks by turning both fuel taps to the off position. This helps prevent siphoning between the tanks as they are being filled. Since the front tanks are mounted higher that the rear tank, fuel will flow out the rear tank over flow when all tanks are full. You must use the fuel in the rear tank before opening the front tanks. LOW FUEL WARNING Due to the extra fuel in the front tanks, the range increases when the low fuel warning light signals. With the front tanks fitted the range from the signal to empty is around 25 km to 60 km, depending on the riding conditions. QUICK DISCONNECTORS Before removing front tanks, you must disconnect the black quick connector by pushing in the stainless tag and gently pulling apart. This is to prevent fuel discharge from the rear tank through the fuel lines. Whilst disconnected we strongly recommend to cover the ends of the quick connectors with a clean plastic bag, latex glove or similar, this prevents debris from entering the connector. Before reconnecting, push in the stainless steel lever and push both halves together taking care. Once connected check for leaks, if the connector is leaking, disconnect again and thoroughly clean O-ring and plunger then reconnect. Refit OEM radiator guard with both special stepped M6 screws into radiator. DO NOT USE LOCTITE OR OVERTIGHTEN Re-connect battery positive terminal and refit red insulating cover.

18 INSTALLATION INSTRUCTIONS AND INFORMATION Decal Installation Instructions

EVO 2 FAIRING Rev6 18/05/ :40:00 1

EVO 2 FAIRING Rev6 18/05/ :40:00 1 EVO 2 FAIRING Rev6 18/05/2014 20:40:00 1 NOTE : BEFORE COMMENCING WORK ON THE CONVERSION, TAKE TIME TO READ THE INSTRUCTIONS CAREFULLY. ALL WORK CAN BE CARRIED OUT BY A COMPETENT MECHANIC, BUT IF YOU ARE

More information

Procharger Stage II Intercooled Supercharger System (11-14 GT)

Procharger Stage II Intercooled Supercharger System (11-14 GT) Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2

More information

HIGH FLOW COLD AIR INTAKE SYSTEM INSTALLATION INSTRUCTIONS D , D A

HIGH FLOW COLD AIR INTAKE SYSTEM INSTALLATION INSTRUCTIONS D , D A HIGH FLOW COLD AIR INTAKE SYSTEM INSTALLATION INSTRUCTIONS D760-0320, D760-0320A 1992-95 325i, is 1995 M3 (3.0L) Parts List: 1 Intake Tube 1 Silicone Hose 1 Air Flow Meter Bracket 1 Hose Clamp (#36z) 1

More information

Cut zip ties and remove 2 plastic wiring harness brackets.

Cut zip ties and remove 2 plastic wiring harness brackets. TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. Included parts: 1 - New Bosch Cp3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Bracket/

More information

SS41HF Mitsubishi Pajero NS & NT V8/V9 Series 3.2 Litre Turbo Diesel (4M41 Engine) 3.8 Litre V6 Petrol (6G76 Engine)

SS41HF Mitsubishi Pajero NS & NT V8/V9 Series 3.2 Litre Turbo Diesel (4M41 Engine) 3.8 Litre V6 Petrol (6G76 Engine) SS41HF Mitsubishi Pajero NS & NT V8/V9 Series 3.2 Litre Turbo Diesel (4M41 Engine) 3.8 Litre V6 Petrol (6G76 Engine) 21/7/2010 Parts List ITEM PART NO DESCRIPTION QTY 1 570-133-200 BODY - SNORKEL (SS41HF)

More information

KJ JEEP COMBINATION BULL BAR WARNING

KJ JEEP COMBINATION BULL BAR WARNING KJ JEEP COMBINATION BULL BAR PRODUCT NUMBER FITTING KIT NUMBER 3450120 6171962 WARNING FOR VEHICLES EQUIPPED WITH SRS AIRBAG WHEN INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS, THE FRONT PROTECTION BAR

More information

INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION

INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION INSTALLATION INSTRUCTIONS 97 FORD EXPEDITION 1. Read the instructions completely and carefully before you begin. Check the kit for proper contents (refer to the part s list and the picture diagrams). Before

More information

3.4L V6 SUPERCHARGER 7 TH INJECTOR KIT

3.4L V6 SUPERCHARGER 7 TH INJECTOR KIT Part Number: 00602-17620-260 00602-17620-261 00602-17620-263 00602-17620-264 00602-17620-274 00602-17620-275 00602-17620-276 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description

More information

97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS

97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS 92RC60500 97-02 JEEP TJ BODY LIFT KIT INSTRUCTIONS Congratulations on your purchase of a new Rough Country 2 /3 Body Lift. We are committed to providing you with the best product available for the best

More information

ITEM QTY CHECK PART NUMBER DESCRIPTION

ITEM QTY CHECK PART NUMBER DESCRIPTION PART #21128 2010 Camaro Cold Air Induction Stage II PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1.

More information

Installation Instructions

Installation Instructions Installation Instructions 2.0T FSI Intake Manifold: Featuring better flow, higher boost capacity, 40% larger plenum volume, and integrated flapper delete; this product will take your 2.0L VW TSI and FSI

More information

COLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: F10 M5 # D Fits: F06/F12/F13 M6 PARTS LIST

COLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: F10 M5 # D Fits: F06/F12/F13 M6 PARTS LIST COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0035 Fits: 2013-15 F10 M5 # D760-0037 Fits: 2012-15 F06/F12/F13 M6 PARTS LIST (1) Left Carbon Airbox Lid (1) Right Carbon Airbox Lid (1) Left Carbon Snorkel

More information

Mahindra Pikup (2009 Production Onwards)

Mahindra Pikup (2009 Production Onwards) Mahindra Pikup (009 Production Onwards) Steel Bull Bar INSTALLATION INSTRUCTIONS Accessory Part No. BBAR07 Installation Time: 60min Approx Bull Bar Weight: 60KG! Important: Please read each step of these

More information

TOYOTA FJ CRUISER / 4RUNNER COLD AIR INTAKE Section I Installation Preparation. 4.0L V6 (1GR) Roller Rocker Part Number(s): PTR

TOYOTA FJ CRUISER / 4RUNNER COLD AIR INTAKE Section I Installation Preparation. 4.0L V6 (1GR) Roller Rocker Part Number(s): PTR Section I Installation Preparation Part Number(s): PTR03-89100 Kit Contents Item # Quantity Reqd. Description 1 1 Air Filter (P/N: PTR43-00083) 2 1 Upper Air Box 3 1 Lower Air Box 4 1 Hump Coupler 5 1

More information

SS175HF ISUZU D-MAX (June 2012 onwards) 3.0Litre, 4 Cylinder Turbo Diesel (4JJ1-TC Hi-Power Engine)

SS175HF ISUZU D-MAX (June 2012 onwards) 3.0Litre, 4 Cylinder Turbo Diesel (4JJ1-TC Hi-Power Engine) SS175HF ISUZU D-MAX (June 2012 onwards) 3.0Litre, 4 Cylinder Turbo Diesel (4JJ1-TC Hi-Power Engine) 01/09/2013 Parts List ITEM PART NO. DESCRIPTION QTY 1 740-133-000 BODY - SNORKEL (SS175HF) 1 2 000-135-800

More information

ITEM PART NO. DESCRIPTION QTY BODY - SNORKEL (SS156HF) ½" AIR RAM ASSEMBLY BRACKET - UPPER MOUNTING 1

ITEM PART NO. DESCRIPTION QTY BODY - SNORKEL (SS156HF) ½ AIR RAM ASSEMBLY BRACKET - UPPER MOUNTING 1 SS156HF SAFARI V-SPEC SNORKEL TOYOTA FORTUNER (Oct 2015 onwards) 2.8L Turbo Diesel D-4D (1GD-FTV Engine) Parts List 10/05/2017 ITEM PART NO. DESCRIPTION QTY 1 322-133-400 BODY - SNORKEL (SS156HF) 1 2 000-135-800

More information

Installation Instructions

Installation Instructions 2011-2013 LML DURAMAX COMPOUND-ADD 2011-2015 LML A Duramax TURBO KIT Add INSTALL A Turbo INSTRUCTIONS Compound Kit Installation Instructions 1-800-955-0476 - www.industrialinjection.com - info@industrialinjection.com

More information

Yamaha Apex Moto-R Kill w/jacobson Roll-over valve Installation Instructions

Yamaha Apex Moto-R Kill w/jacobson Roll-over valve Installation Instructions OFTRacing.com Email Scott Moto 2006-2011 Yamaha Apex Moto-R Kill w/jacobson Roll-over valve Installation Instructions Included Parts: 1 Moto-r Kill wiring harness including Pro Armor tether switch, Jacobsen

More information

SS740HF NISSAN D23 NAVARA (NP300) 2.3Ltr Intercooled Twin Turbo(YS23DDTT Engine) Built: Nissan Motor Co. Thailand

SS740HF NISSAN D23 NAVARA (NP300) 2.3Ltr Intercooled Twin Turbo(YS23DDTT Engine) Built: Nissan Motor Co. Thailand SS740HF NISSAN D23 NAVARA (NP300) 2.3Ltr Intercooled Twin Turbo(YS23DDTT Engine) Built: Nissan Motor Co. Thailand Parts List 21/12/2015 ITEM PART NO. DESCRIPTION QTY 1 435-133-000 BODY - SNORKEL (SS740HF)

More information

BA /02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07)

BA /02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07) BA-2020-00/02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07) Page: 1 Revision: 6.2-02/23/2011 Install Time: 1.5 Hours We recommend a qualified Yamaha technician install this kit

More information

SS188HF Toyota Land Cruiser Prado 150 Series KDJ150R 3.0L 4 Cyl. D-4D Diesel (1KD-FTV Engine)

SS188HF Toyota Land Cruiser Prado 150 Series KDJ150R 3.0L 4 Cyl. D-4D Diesel (1KD-FTV Engine) SS188HF Toyota Land Cruiser Prado 150 Series KDJ150R 3.0L 4 Cyl. D-4D Diesel (1KD-FTV Engine) Parts List 8/7/2010 ITEM PART NO. DESCRIPTION QTY 1 365-133-000 BODY - SNORKEL (SS188HF) 1 2 000-135-800 3

More information

MAZDA BT-50 (October 2011 Production Onwards) 1 & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS

MAZDA BT-50 (October 2011 Production Onwards) 1 & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS MAZDA BT-50 (October 0 Production Onwards) & 3 PIECE HARD TONNEAU REMOTE LOCKING KIT INSTALLATION INSTRUCTIONS Installation Time: Approx. 0 Minutes Care Instructions: Clean Tonneau Cover with a mild detergent

More information

INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063

INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 INSTALLATION INSTRUCTIONS FORD F-150 2WD & 4WD RETAINS FACTORY TOW HOOKS PART #P3063 PARTS LIST: 1 Grille Guard 2 10-1.5mm Nylon Lock Nuts 1 Driver/Left Frame Mounting Bracket 4 12mm Plastic Washers 1

More information

8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles)

8 Zip Tie Zip Tie 1 Union Fitting 1 ½ ½ Union Reducer Fitting Union 1 5/8 ½ (For Plastic Intake Manifold Vehicles) P IAG Street Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7151 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,

More information

JEEP CHEROKEE, WAGONEER (XJ) FRONT BUMPER INSTALLATION INSTRUCTIONS KIT# W/ WINCH KIT# 83203

JEEP CHEROKEE, WAGONEER (XJ) FRONT BUMPER INSTALLATION INSTRUCTIONS KIT# W/ WINCH KIT# 83203 3651 N Highway 89 Chino Valley, AZ 86323 (928) 636-7080 www.p-a-g.net JEEP CHEROKEE, WAGONEER (XJ) FRONT BUMPER INSTALLATION INSTRUCTIONS 1984-2001 KIT# 83202 1984-2001 W/ WINCH KIT# 83203 WARNING Before

More information

IAG Competition Series Air / Oil Separator (AOS) For 2017 STI

IAG Competition Series Air / Oil Separator (AOS) For 2017 STI P IAG Competition Series Air / Oil Separator (AOS) For 2017 STI Part# IAG-ENG-7251 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,

More information

4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side

4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side 2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and

More information

All cores due 30 days after invoice date - no credit after 60 days.

All cores due 30 days after invoice date - no credit after 60 days. NO WARRANTY STATEMENT High performance parts & products no warranty policy: The purchaser understands and recognizes that high performance diesel products and services sold by INDUSTRIAL INJECTION SERVICE.

More information

2015 Mustang Lightbar (All Models) CDC#

2015 Mustang Lightbar (All Models) CDC# 2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket

More information

Current Range Rover Sport STRUT Collection Installation Manual

Current Range Rover Sport STRUT Collection Installation Manual 2014 - Current Range Rover Sport STRUT Collection Installation Manual 1 1. Removing Main Grille and Lower Fascia 1.1 Run a line of low tack masking tape across the front of the bumper below the grille

More information

Part Number: S-H-BAG-8 & S-H-8-RFEN Description: Saddlebags & Rear Fender / Undertail Fitment: Suzuki GSX 1300-R Hayabusa Revision: 1

Part Number: S-H-BAG-8 & S-H-8-RFEN Description: Saddlebags & Rear Fender / Undertail Fitment: Suzuki GSX 1300-R Hayabusa Revision: 1 Part Number: S-H-BAG-8 & S-H-8-RFEN Description: Saddlebags & Rear Fender / Undertail Fitment: 2008-2009 Suzuki GSX 1300-R Hayabusa Revision: 1 Tools Required Phillips head screwdriver Small screwdriver

More information

BoonDocker Nitrous System Installation Instructions for Kawasaki KFX-700 ATV

BoonDocker Nitrous System Installation Instructions for Kawasaki KFX-700 ATV BoonDocker Nitrous System Installation Instructions for Kawasaki KFX-700 ATV Before you begin, please read the instructions below and check kit contents Nitrous Kit Contents: 1 Nitrous Manifold with fittings

More information

Factory safe air/fuel ratio s for Optimum performance Patent# 7,359,795 Now equipped with Air Fusion

Factory safe air/fuel ratio s for Optimum performance Patent# 7,359,795 Now equipped with Air Fusion Part number PF7010 2010 Chevy Camaro 3.6L V6 1-4 diameter intake system equipped with MR Tech and Air Fusion 1-3 1/2 neck Injen/AMSOIL (#1021) Performance dry filter w/f1 style inverted top 1-3 1/8 x 3

More information

SS985HF Mazda BT-50 B32P Series 3.2L 5cylinder TDCi Diesel (P5AT Engine)

SS985HF Mazda BT-50 B32P Series 3.2L 5cylinder TDCi Diesel (P5AT Engine) SS985HF Mazda BT-50 B32P Series 3.2L 5cylinder TDCi Diesel (P5AT Engine) Parts List 01/03/2013 ITEM PART NO. DESCRIPTION QTY 1 685-133-000 BODY - SNORKEL (SS985HF) 1 2 000-135-800 3 ½" AIR RAM ASSEMBLY

More information

LAND ROVER DISCOVERY 3 ARB BULL BAR AND WINCH BAR WARNING

LAND ROVER DISCOVERY 3 ARB BULL BAR AND WINCH BAR WARNING LAND ROVER DISCOVERY 3 ARB BULL BAR AND WINCH BAR PART No 3432150 DISCOVERY 3 WINCH BAR PART No 3232150 DISCOVERY 3 BULL BAR WARNING FOR VEHICLES EQUIPPED WITH SRS AIRBAG WHEN INSTALLED IN ACCORDANCE WITH

More information

LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions

LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and

More information

Cut zip ties and remove 2 plastic wiring harness brackets.

Cut zip ties and remove 2 plastic wiring harness brackets. TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please email H&S Motorsports

More information

Performance Inlet Manifold

Performance Inlet Manifold Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with

More information

LAND ROVER DISCOVERY 3/ SPARE WHEEL CARRIER

LAND ROVER DISCOVERY 3/ SPARE WHEEL CARRIER LAND ROVER DISCOVERY 3/ 4 SPARE WHEEL CARRIER RBLD007 INSTALL TIME: 4.5 Hours NOTE: Park Distance Control will be affected by this fitment and the customer should be informed. IMPORTANT WARNING! IT IS

More information

Slingshot Rotrex Supercharger Kit

Slingshot Rotrex Supercharger Kit Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you

More information

ITEM PART NO. DESCRIPTION QTY BODY - SNORKEL (SS982HF) ½" AIR RAM ASSEMBLY BRACKET - UPPER MOUNTING 1

ITEM PART NO. DESCRIPTION QTY BODY - SNORKEL (SS982HF) ½ AIR RAM ASSEMBLY BRACKET - UPPER MOUNTING 1 SS984HF SAFARI V-SPEC SNORKEL Ford Everest 1 (All Models) 3.2L TDCi Diesel (P5AT Engine) Parts List 24/10/2016 ITEM PART NO. DESCRIPTION QTY 1 680-133-300 BODY - SNORKEL (SS982HF) 1 2 000-135-800 3 ½"

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS HIGH FLOW AIRFLOW METER INSTALLATION INSTRUCTIONS PART NUMBER D763-1600A APPLICATION: 2001-06 E46 M3 Parts List: Hose clamp 64Z (7) Plastic Rivets Air Filter Temp Sensor & Harness (2) Button Head Screws

More information

INSTALLATION MANUAL P2068. Level of Difficulty. Parts List. Product Image. Notes and Maintenance. Tools Required. Easy

INSTALLATION MANUAL P2068. Level of Difficulty. Parts List. Product Image. Notes and Maintenance. Tools Required. Easy INSTALLATION MANUAL P2068 Parts List 1 Grille guard 1 Driver / left frame mounting bracket 1 Passenger / right frame mounting bracket 1 Driver / left top mounting bracket 1 Passenger / right top mounting

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0390C APPLICATION: 1999-2003 E39 M5 PARTS LIST 1 Left Aluminum Intake Tube 1 Air Pump Bracket (A) 1 Right Aluminum Intake Tube 1 Air Pump Bracket

More information

AEV30243AK Last Updated: 05/01/18. 3 Dualsport front suspension ram truck 2500/3500 INSTALLATION GUIDE

AEV30243AK Last Updated: 05/01/18. 3 Dualsport front suspension ram truck 2500/3500 INSTALLATION GUIDE AEV30243AK Last Updated: 05/01/18 3 Dualsport front suspension ram truck 2500/3500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND READING THESE INSTRUCTIONS

More information

MOROSO PERFORMANCE PRODUCTS, INC. (203) , 80 CARTER DRIVE GUILFORD, CT

MOROSO PERFORMANCE PRODUCTS, INC. (203) , 80 CARTER DRIVE GUILFORD, CT Parts List (2) Air Oil separator (2) Billet Clamp (1) Stainless Mounting Bracket (2) Ball Valve (2) 90 Degree drain (2) ¼-20X1 SHCS (4) ¼-20x5/8 SHCS (2) ¼-20X1 HHCS (2) ¼-20 Nylock Nuts (2) ½ x 90 Barbed

More information

INSTALLATION GUIDE PREMIUM FRONT BUMPER FOR RAM AEV30304AA Last Updated: 09/18/17

INSTALLATION GUIDE PREMIUM FRONT BUMPER FOR RAM AEV30304AA Last Updated: 09/18/17 AEV30304AA Last Updated: 09/18/17 PREMIUM FRONT BUMPER FOR RAM 1500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START To guarantee a quality installation, we recommend reading these instructions thoroughly

More information

COLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: i (4.8L)

COLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: i (4.8L) COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0013 Fits: 2006-10 650i (4.8L) PARTS LIST Air Box Assembly Left tube Center tube Right tube Support bracket AFM housing AFM/TB tube Hardware Kit Congratulations

More information

2015+ EcoBoost F150 & Raptor Intercooler Install

2015+ EcoBoost F150 & Raptor Intercooler Install 2015+ EcoBoost F150 & 2017+ Raptor Intercooler Install Note: This entire job can be performed with the truck on the ground - No need to raise the vehicle. The most difficult part is removing the grille

More information

FITTING KIT No s : BULL BAR WINCH ( P/No ) BULL BAR NON WINCH ( P/No )

FITTING KIT No s : BULL BAR WINCH ( P/No ) BULL BAR NON WINCH ( P/No ) ARB WINCH / NON WINCH BULL BAR TO SUIT LANDROVER DISCOVERY 2003 ONWARD. FITTING KIT No s :- 617 1793 BULL BAR WINCH ( P/No 343 2120 ) 617 1794 BULL BAR NON WINCH ( P/No 323 2120 ) WARNING FOR VEHICLES

More information

RMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.

RMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com. RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.

More information

INSTALLATION INSTRUCTIONS CATCH CAN KIT

INSTALLATION INSTRUCTIONS CATCH CAN KIT INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1 TO 19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN

More information

Always wear safety glasses when working on your vehicle.

Always wear safety glasses when working on your vehicle. 90-93 MAZDA MIATA SUPERCHARGER KIT The KraftWerks 90-93 Mazda Miata Supercharger Kit was designed for easy installation. Competent mechanics with the appropriate tools will find the process to be relatively

More information

SHELBY GT500

SHELBY GT500 2007-2009 SHELBY GT500 Removal of Factory Unit WARNING: 1. Radiator fluid must be handled properly. Please observe local ordinances with regards to handling and disposal. 2. Allow vehicle and components

More information

SS89HP SAFARI ARMAX SNORKEL Toyota Land Cruiser 200 Series (MY16 Face Lift) 1VD-FTV 4.5Litre-V8 Intercooled Twin Turbo Diesel (Does not suit GX model)

SS89HP SAFARI ARMAX SNORKEL Toyota Land Cruiser 200 Series (MY16 Face Lift) 1VD-FTV 4.5Litre-V8 Intercooled Twin Turbo Diesel (Does not suit GX model) SS89HP SAFARI ARMAX SNORKEL Toyota Land Cruiser 200 Series (MY16 Face Lift) 1VD-FTV 4.5Litre-V8 Intercooled Twin Turbo Diesel (Does not suit GX model) Parts List 01/12/2016 ITEM PART NO. DESCRIPTION QTY

More information

INSTALLATION GUIDE HOLDEN COLORADO (RG) INTERCOOLER KIT P/N PWI66175K INTERCOOLER P/N PWA64553 ( ) PIPE KIT

INSTALLATION GUIDE HOLDEN COLORADO (RG) INTERCOOLER KIT P/N PWI66175K INTERCOOLER P/N PWA64553 ( ) PIPE KIT INSTALLATION GUIDE HOLDEN COLORADO (RG) INTERCOOLER KIT P/N PWI66175K INTERCOOLER P/N PWA64553 (2012-13) PIPE KIT ENGINEERING THE UNFAIR ADVANTAGE Contents CONDITIONAL MANUFACTURERS WARRANTY... 2 Warranty

More information

INSTALLATION GUIDE VW AMAROK INTERCOOLER KIT P/N PWI63123 INTERCOOLER P/N PWA64398 PIPE KIT

INSTALLATION GUIDE VW AMAROK INTERCOOLER KIT P/N PWI63123 INTERCOOLER P/N PWA64398 PIPE KIT INSTALLATION GUIDE VW AMAROK INTERCOOLER KIT P/N PWI63123 INTERCOOLER P/N PWA64398 PIPE KIT ENGINEERING THE UNFAIR ADVANTAGE Contents CONDITIONAL MANUFACTURERS WARRANTY... 2 Warranty voids... 2 Warranty

More information

RANGER 900 POWER STEERING KIT

RANGER 900 POWER STEERING KIT RANGER 900 POWER STEERING KIT P/N 2880083 APPLICATION MY14 AND NEWER RANGER XP 900 MODELS IMPORTANT It is strongly recommended that this kit be installed by an authorized Polaris dealer. NOTE Use of this

More information

HYPERMAX ENGINEERING, INC. 7.3L POWER STROKE INTERCOOLER PACKAGE

HYPERMAX ENGINEERING, INC. 7.3L POWER STROKE INTERCOOLER PACKAGE HYPERMAX ENGINEERING, INC. 7.3L POWER STROKE INTERCOOLER PACKAGE INSTALLATION INSTRUCTIONS Time will be saved if these instructions are read PRIOR to installation of the intercooler package. A. ITEMS TO

More information

BLACKBIRD INSTALLATION SUPPLEMENT

BLACKBIRD INSTALLATION SUPPLEMENT BLACKBIRD INSTALLATION SUPPLEMENT FOR5.3 AND 6 LITER VORTEC SUBURBAN/YUKON/SILVERADO VERSION 2-06 Blackbird Installation Supplement for GM 5.3 and 6 liter Vortec-Suburban/Silverado Parts Included in Installation

More information

READ ME! IMPORTANT WARNING! ENG. Auxiliary 80l Fuel Tank Toyota Hilux DC 2005-Current

READ ME! IMPORTANT WARNING! ENG. Auxiliary 80l Fuel Tank Toyota Hilux DC 2005-Current Auxiliary 80l Fuel Tank Toyota Hilux DC 2005-Current ENG FTTH011 READ ME! Thank you for purchasing a Front Runner Fual Tank. Before you start, take a moment to familiarize yourself with the Fitting Instructions

More information

SCION xb PERFORMANCE AIR INTAKE Section I Installation Preparation 2.4L I-4

SCION xb PERFORMANCE AIR INTAKE Section I Installation Preparation 2.4L I-4 Section I Installation Preparation 2.4L I-4 Part Number(s): PTR03-52110 Kit Contents Item # Quantity Description Reqd. 1 1 TRD Inlet Tube 2 1 TRD Upper Air Box with HC Trap 3 1 Hump Hose Coupler 4 1 Hump

More information

Installation Instructions for: TOYOTA 3.4L SUPERCHARGER SYSTEM

Installation Instructions for: TOYOTA 3.4L SUPERCHARGER SYSTEM Installation Instructions for: TOYOTA 3.4L SUPERCHARGER SYSTEM 1996-2002 4Runner 1997-1998 T100 1997-2004 Tacoma 2000-2003 Tundra * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg

More information

Holden VE SIDI series II V6 OTR CAI Installation Instructions

Holden VE SIDI series II V6 OTR CAI Installation Instructions Holden VE SIDI series II V6 OTR CAI Installation Instructions 1 P a g e Shown above is a standard V6 VE LFW SIDI engine bay. Your MAF Loom may need to be extended by an auto electrician. Please check the

More information

Product Packing List

Product Packing List Product Packing List Product: SDHQ-55-1650-G3 Description: 2016+ Toyota Tacoma Hidden Winch Mount (1) Winch Mount SDHQ-55-1650-G3-A (2) Lower Support Brackets SDHQ-55-1650-G3-B (1) Lower Bumper Bracket

More information

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER DS (GUN METAL GRAY FINISH)

Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER DS (GUN METAL GRAY FINISH) Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-823DS (GUN METAL GRAY FINISH) 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-202DOSK AIR FILTER; OFFSET 2.75" X

More information

COLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: i (4.8L)

COLD AIR INTAKE INSTALLATION INSTRUCTIONS. # D Fits: i (4.8L) COLD AIR INTAKE INSTALLATION INSTRUCTIONS # D760-0012 Fits: 2006-10 550i (4.8L) PARTS LIST Air Box Assembly Left tube Center tube Right tube Outer Tube AFM housing AFM/TB tube Hardware Kit Congratulations

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-696 2009-2010 DODGE Challenger V6-3.5L SEE * NOTE * NOTE: Legal in California only for racing vehicles which

More information

INSTALLATION GUIDE. 3 Dualsport suspension. ram truck 2500/3500. AEV30243AA Last Updated: 04/10/15

INSTALLATION GUIDE. 3 Dualsport suspension. ram truck 2500/3500. AEV30243AA Last Updated: 04/10/15 3 Dualsport suspension AEV30243AA Last Updated: 04/10/15 ram truck 2500/3500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND READING THESE INSTRUCTIONS

More information

Tusk Pannier Racks. Instructions and information KLR

Tusk Pannier Racks. Instructions and information KLR 1 Tusk Pannier Racks Instructions and information KLR650 2008 + Congratulations on your purchase of the Tusk Pannier Racks. These racks are made to handle extreme adventure riding, but work great for the

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS 2012-2014 F-150 4 MyFord factory display 360º Vision System (Kit # AVMS-3604) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Video

More information

ITEM PART NO. DESCRIPTION QTY BODY - SNORKEL (SS89HF) ½" AIR RAM ASSEMBLY BRACKET - UPPER MOUNTING 1

ITEM PART NO. DESCRIPTION QTY BODY - SNORKEL (SS89HF) ½ AIR RAM ASSEMBLY BRACKET - UPPER MOUNTING 1 SS89HF SAFARI V-SPEC SNORKEL Toyota Land Cruiser 200 Series (MY16 Face Lift) 1VD-FTV 4.5Litre-V8 Intercooled Twin Turbo Diesel (Does not suit GX model) 22/03/2016 Parts List ITEM PART NO. DESCRIPTION QTY

More information

1 M-3000-H4 F150 4X4 Lowering Kit

1 M-3000-H4 F150 4X4 Lowering Kit READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.

More information

Buy products from authorized and licensed manufacturers using any of our patented processes, beware of cheap knock-offs, look for our licensing logo.

Buy products from authorized and licensed manufacturers using any of our patented processes, beware of cheap knock-offs, look for our licensing logo. Part number SP2096 2008-10 Lexus IS-F 5.0L V8 1- Air intake system equipped with MR Tech and Air Fusion 1-5 Injen/AMSOIL (#1046) dry filter w/f1 styleinverted top 1-4 straight hose (#3129) 1-3 1/4 x 3

More information

Always use fuel with a minimum octane rating of 93 (R+M)/2. (Equivalent to 98 RON).

Always use fuel with a minimum octane rating of 93 (R+M)/2. (Equivalent to 98 RON). Before Commencing Installation Verify that you have all necessary tools as listed. Clean all air ducting prior to commencing installation. The sequence of installation of each part is very important. It

More information

Brake Upgrade Kit Fitting Instructions Bonneville America

Brake Upgrade Kit Fitting Instructions Bonneville America WARNING: Always have Triumph approved parts, accessories and conversions fitted by a trained technician of an authorised Triumph Dealer. The fitment of parts, accessories and conversions by a technician

More information

#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS

#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS #TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When

More information

SS732HF NISSAN D40 NAVARA / R51 PATHFINDER 4.0Ltr V6 Petrol (VQ40 Engine) Built: Nissan Motor Iberica, S.A.

SS732HF NISSAN D40 NAVARA / R51 PATHFINDER 4.0Ltr V6 Petrol (VQ40 Engine) Built: Nissan Motor Iberica, S.A. SS732HF NISSAN D40 NAVARA / R51 PATHFINDER 4.0Ltr V6 Petrol (VQ40 Engine) Built: Nissan Motor Iberica, S.A. Parts List 31/03/2014 ITEM PART NO. DESCRIPTION QTY 1 430-133-000 BODY - SNORKEL (SS730HF) 1

More information

Included parts: 1 - New Bosch CP3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Bracket/ Hardware STEP 1

Included parts: 1 - New Bosch CP3 Pump 1 - HSM Pulley 1 - Serpentine Belt 1 - Pump Bracket/ Hardware STEP 1 TROUBLESHOOTING: Please read and understand all installation instructions before proceeding with the installation. If you have questions during the installation of this product, please contact H&S Motorsports

More information

Bill of Materials for

Bill of Materials for Bill of Materials for 77060012 1 2-P5153572 Inlet Pipe 1 21-202M 2.75" Filter 1 103-BLO-4820N Filter Hose Clamp 1 559999 Washer, Fender M6x25 1 1-3028 Washer, 1/4 SAE Flat 1 1-2072 Bolt, 1/4-20-UNC x 1

More information

WARNING. ARB 4x4 ACCESSORIES. Corporate Head Office Garden St Tel: +61 (3) Kilsyth, Victoria Fax: +61 (3) AUSTRALIA 3137

WARNING. ARB 4x4 ACCESSORIES. Corporate Head Office Garden St Tel: +61 (3) Kilsyth, Victoria Fax: +61 (3) AUSTRALIA 3137 Part Number: 3440400 Product Description: Suited to vehicle/s: Winch Install Kit: DELUXE WINCH BULL BAR FORD RANGER PX 2011ON 3540050 WARNING REGARDING VEHICLES EQUIPPED WITH SRS AIRBAG; When installed

More information

TSS Fit Kit Installation Instructions Timbersled Snow Bike System

TSS Fit Kit Installation Instructions Timbersled Snow Bike System TSS Fit Kit Installation Instructions Timbersled Snow Bike System Information needed before you start: Read the entire installation instructions before starting. The instruction sheet is universal for

More information

SS1066HF Jeep JK Wrangler Left Hand Drive CRDI4 2.8Litre-I4 Diesel Engine and EGHV6 3.8Litre V6 Gasoline Engine

SS1066HF Jeep JK Wrangler Left Hand Drive CRDI4 2.8Litre-I4 Diesel Engine and EGHV6 3.8Litre V6 Gasoline Engine SS1066HF Jeep JK Wrangler Left Hand Drive CRDI4 2.8Litre-I4 Diesel Engine and EGHV6 3.8Litre V6 Gasoline Engine Installation Guide Safari SS1066HF Page - 1 of 12 6/10/2009 ITEM PART NO DESCRIPTION QTY

More information

2010 Mustang V6 Shaker CDC #

2010 Mustang V6 Shaker CDC # - - Incomplete 2010 Mustang V6 Shaker CDC # 1011-7002-01 Component Check List: Quantity/Description Part # Engine Cover Assembly 1011-6000-01 1 Engine Cover w/ Upper Air Tube 0511-2100-01 1 Aluminum Shaker

More information

INSTALLATION INSTRUCTIONS CATCH CAN KIT MITSUBISHI EVOLUTION X Document# Customer Support:

INSTALLATION INSTRUCTIONS CATCH CAN KIT MITSUBISHI EVOLUTION X Document# Customer Support: The EVOX catch can kit is available in 3 variations. The PCV kit installs between the PCV valve and the intake manifold. The crankcase kit installs between the valve cover vent port and the pre-turbo air

More information

INSTALLATION INSTRUCTIONS CATCH CAN KIT

INSTALLATION INSTRUCTIONS CATCH CAN KIT INSTALLATION INSTRUCTIONS CATCH CAN KIT FORD FOCUS Document: 19-0150 Support: info@radiumauto.com STEPS 1-19 COVER THE PCV SIDE CATCH CAN KIT (P/N: 20-0315) STEPS 20-32 COVER THE CRANKCASE CATCH CAN KIT

More information

Mustang Shaker

Mustang Shaker 2005-2009 Mustang Shaker CDC #110050 ( 05/ 06) or 0711-7000-01 ( 07/ 09) Component Check List: Quantity/Description Part # CDC Installer 1 - Engine Cover Assembly 114050 1 - Aluminum Shaker Scoop 183020

More information

JEEP WRANGLER (TJ), UNLIMITED (TJL), RUBICON MODELS BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT# KIT# 973

JEEP WRANGLER (TJ), UNLIMITED (TJL), RUBICON MODELS BODY LIFT KIT INSTALLATION INSTRUCTIONS KIT# KIT# 973 JEEP WRANGLER (TJ), UNLIMITED (TJL), RUBICON MODELS BODY LIFT KIT INSTALLATION INSTRUCTIONS 1997-2006 2 KIT# 972 3 KIT# 973 WARNING Installation of a Performance Automotive Group body lift will change

More information

XRT300 AND XRT350 BA XR6 TURBO UPGRADE KIT FITTING INSTRUCTIONS

XRT300 AND XRT350 BA XR6 TURBO UPGRADE KIT FITTING INSTRUCTIONS XRT300 AND XRT350 BA XR6 TURBO UPGRADE KIT FITTING INSTRUCTIONS The use of NFU (No Further use) and REUSE (Re Use) relates to the individual parts storage when performing the upgrade. Also note that all

More information

APS F-Body Twin Pump Fuel Supply System - APSGMF-FSS/01

APS F-Body Twin Pump Fuel Supply System - APSGMF-FSS/01 APS F-Body Twin Pump Fuel Supply System - APSGMF-FSS/01 1 Remove the fuel tank from the vehicle in accordance with the factory service manual. 2 Remove the stock fuel pump assembly from the fuel tank in

More information

The M7 Direct Flow Intercooler (DFIC) Installation Guide

The M7 Direct Flow Intercooler (DFIC) Installation Guide The M7 Direct Flow Intercooler (DFIC) Installation Guide This information is meant only as a guide. The author of this information,, or any M7 Tuning employees assumes no liabilities for any outcomes resulting

More information

2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014

2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014 2010+ Victory Cross Country / Cross Roads Installation Guide Nov 2014 125 Industrial Drive Spearfish, SD 57783 Toll Free 888.3WHEELS w w w. l e h m a n t r i k e s. c o m UNDERSTANDING SAFETY LABELS &

More information

INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support:

INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support: INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi Document# 19-0102 Support: info@radiumauto.com These instructions are based on a vehicle with an OEM turbocharger

More information

AEV30243AJ Last Updated: 11/14/17. 3 Dualsport front suspension ram truck 2500/3500 INSTALLATION GUIDE

AEV30243AJ Last Updated: 11/14/17. 3 Dualsport front suspension ram truck 2500/3500 INSTALLATION GUIDE AEV30243AJ Last Updated: 11/14/17 3 Dualsport front suspension ram truck 2500/3500 INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND READING THESE INSTRUCTIONS

More information

MOUNTAIN HORSE INSTALL KIT

MOUNTAIN HORSE INSTALL KIT MOUNTAIN HORSE INSTALL KIT P/N 9928508 APPLICATION Installation Instructions are for all Mountain Horse TSS and TFS Installation Kits and Timbersled Mountain Horse chassis installations. The Timbersled

More information

BD Venom Dual Fuel F O R D 6. 7 L P O W E R S T R O K E Installation Instructions

BD Venom Dual Fuel F O R D 6. 7 L P O W E R S T R O K E Installation Instructions U 21 March 2017 (1050470) Venom Dual Fuel Kit (I-00390) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Venom Dual Fuel 2 0 1 1-2 0 1 6 F O R D 6. 7 L P O W E R S T R O K E Installation

More information

Volvo P1 Air Intake. ELEVATE Turbo Intake Pipe. MAF Sensor. Inlet Manifold. Air Filter Housing. ECU Cover

Volvo P1 Air Intake. ELEVATE Turbo Intake Pipe. MAF Sensor. Inlet Manifold. Air Filter Housing. ECU Cover Volvo P1 Air Intake Tools needed: 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 8mm Combination Wrench and/or Socket with Ratchet 10mm Combination Wrench and/or Socket

More information

Depress each tab as you pull the bezel off. The bezels are tight. L.H. shown.

Depress each tab as you pull the bezel off. The bezels are tight. L.H. shown. 2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR

More information

Arctic Cat ProClimb Sidekick Installation Instructions

Arctic Cat ProClimb Sidekick Installation Instructions 2013-2017 Arctic Cat ProClimb Sidekick Installation Instructions 1.Remove side panels, front bumper, and hood 2. Remove pipe, muffler, heat shield and ECU 3. Remove cross brace. Unplug the servo motor

More information

BD Venom Dual Fuel F O R D 6. 7 L P O W E R S T R O K E Installation Instructions

BD Venom Dual Fuel F O R D 6. 7 L P O W E R S T R O K E Installation Instructions U 30 January 2017 (1050470) Venom Dual Fuel Kit (I-00390) 1 DOWNLOAD ENHANCED INSTALL MANUALS AT dieselperformance.com BD Venom Dual Fuel 2 0 1 1-2 0 1 4 F O R D 6. 7 L P O W E R S T R O K E Installation

More information