Set-Up and Usage Instructions

Transcription

1 4-WAY GRAVITY-DROP AND REBOUNDER SYSTEM Set-Up and Usage Instructions Joe Mauer» AL Batting Champion 06, 08, 09» 2009 League MVP

2 Warning: Always wear a helmet with face guard Improper use of this product can result in serious injury. Read and follow enclosed instructions for the proper and safe use of QuickSwing PX4 before you begin. QUICKSWING PX4 PARTS LIST Before you begin assembly, check your inventory. Lay all the pieces out to make sure you have received all required parts and components. You will need a Phillips-head screwdriver for the battery cover and 3 AA batteries for the motor. Please contact SKLZ customer service toll free at x128 if you are missing anything. QUICKSWING PX4 PARTS: D Auto-feed Motor A Base Stand B Telescoping Base Pole C Support Clamp E Motor Clamp F Rotatable End Dial G Feeder Tube H Straight Tube REBOUNDER PARTS: I Frame & Legs (2) K Net J Frame Connectors (2) L Bungees (14)

3 QUICKSWING PX4 AUTO-FEED & REBOUNDER NET Motor Clamp (E) Feeder Tube (G) Rotatable End Dial (F) Not used when using the rebounder Straight Tube (H) Support Clamp (C) Auto-feed Motor (D) Telescoping Base Pole (B) Net (K) Bungees (L) Frame Connector (J) Frame & Legs (I) Base Stand (A) Angle Adjustable Leg MANUAL-FEED PARTNER-FEED SKLZ.com

4 INSTRUCTIONS FOR AUTO-FEED SET-UP: STEP 1 BASE STAND AND TELESCOPING BASE POLE ASSEMBLY Fully extend the legs of the Base Stand (A) until they lock into place. Stand the base on the ground. Attach Telescoping Base Pole (B) into the top of the Base Stand (A) by lining up the push pin with the hole. Lock push pin into place. STEP 2 ATTACH THE SUPPORT CLAMP AND TUBES Slide the Support Clamp (C) into the Telescoping Base Pole (B) and secure with the knobs on the pole. Attach the Feeder Tube (G) and Straight Tube (H) together. Flanged end of the Straight Tube will fit over the Feeder Tube and motor slot should be facing the ground. Slide the tubes into the Support Clamp (C) and clamp. Note: Make sure that the straight tube is angled down, as pictured below. G H STEP 3 PLACE 3 AA BATTERIES INTO AUTO-FEED MOTOR (Batteries not Included) Unscrew the battery cover on the Auto-Feed Motor (D) with a Phillips-head screwdriver. Install 3 AA batteries into the motor and replace cover. Slide Auto-Feed Motor (D) into Motor Clamp (E) (make sure to slide the motor in all the way). E D

5 STEP 4 ATTACH THE MOTOR Slide the Auto-Feed Motor with Clamp (D & E) into the slot on the bottom of the Straight Tube (H). Make sure the retaining pin slides into pin hole and then clamp. H Pin NOTE: Be sure the on/off button is on the same side as the white guide on the tube. STEP 5 ATTACH THE ROTATABLE END TUBE Attach the Rotatable End Tube (F) to the Straight Tube (H). You should be able to turn the Rotatable End Tube (F) to your desired angle. NOTE: The Rotatable End Tube will only be used when you are NOT using the rebounder. H F STEP 6 LOAD BALLS AND ADJUST SPEED Make sure the pin is in the pin hole and load the QuickSwing PX4 with balls. Adjust the timer on the motor for how fast or slow you want the balls to drop out of the QuickSwing PX4. Remove pin then move the switch to the ON position. If you want to change the speeds, turn off the motor first and then adjust the speed. INSTRUCTIONS FOR PARTNER-FEED SET-UP: Set up the QuickSwing PX4 the same way you would for the QuickSwing PX4 Auto-Feed but do not attach the motor. Partner-Feed can be used for any of the 4 configurations for the QuickSwing PX4. SKLZ.com

6 INSTRUCTIONS FOR MANUAL-FEED SET-UP: Follow STEP 1 BASE STAND AND TELESCOPING BASE POLE ASSEMBLY from the Auto-Feed set-up. STEP 2 ATTACH THE SUPPORT CLAMP AND TUBES Slide the Support Clamp (C) into the Telescoping Base Pole (B) and secure with the knob on the pole. Clamp the Feeder Tube (G) into the Support Clamp (C). NOTE: Slide the Feeder Tube (G) as far forward as you can. You will only attach one bracket on the clamp to allow for enough hitting room. H Attach the Straight Tube (H) to the Feeder Tube (G). Straight Tube will fit over the top of the Feeder Tube. STEP 3 ATTACH THE ROTATABLE END TUBE Attach the Rotatable End Tube (F) to the Feeder Tube (G). You should be able to rotate the Rotatable End Tube (F) to desired angle. ROTATABLE END TUBE: The QuickSwing PX4 rotatable end tube fully rotates to allow you to control how fast the ball drops before you hit it. You will only use the Rotatable End Tube when you are not using the QuickSwing PX4 with the Rebounder.» For a slower ball drop, adjust the end tube to a horizontal position.» For an average ball drop, adjust the end tube to a 45 degree angle.» For a quick ball drop, adjust the end tube to a downward position.

7 REBOUNDER SET-UP: STEP 1 ASSEMBLE THE REBOUNDER FRAME Fold out the legs 90 on each Frame & Legs (I) and slide the locking pin through each leg to secure. Lay on the ground with the legs up. Connect both Frame Connectors (J) to one Frame & Legs (I). Lock into place with the push pins. The push pins lock into place on the bottom of the Frame. Slide the other Frame & Legs (I) onto the other ends of the Frame Connectors (J) and lock into place. NOTE: For easy attachment slide the frame onto each connector simultaneously. J I I J I STEP 2 ATTACH THE REBOUNDER NET Adult assembly recommended. With the completed frame upside down, lay the Net (K) inside the frame. Starting at position 1 (see diagram) on the frame, slide the bungee head under the net and through the net square. Wrap the bungee around the frame and loop the end of the bungee over the bungee head to secure the net to the frame. NOTE: Make sure that the Bungee head is facing up, this will ensure that when you flip the rebounder back over the Bungee heads will be under the net and will not impact the bounce of the ball. Attach the remaining bungees in the same fashion. For easy net attachment make sure to attach the bungee cords in the numerical order you see them on the diagram Your Rebounder Net is now ready for use ORDER OF BUNGEE ATTACHMENT SKLZ.com

8 STEP 3 ADJUSTING THE REBOUNDER ANGLE Flip the Rebounder Net over so it is standing on the ground. Remove the locking pin from each angle adjustment leg. Move the leg to the desired angle and replace the locking pin. Make sure that the angle is the same for both legs. Angle Adjustment Leg HOW TO USE THE QUICKSWING PX4 FOUR WAYS: AUTO-FEED GRAVITY DROP: Set up the QuickSwing PX4 at least a foot above your swing height. Position the dial to fit your skill level. Balls will drop every 6, 8 or 10 seconds. You can also set up the QuickSwing PX4 in the manual position. The auto-feed gravity drop pitch allows for batters to work on skills essential for game day. This includes increasing bat speed, better hand-eye coordination and faster reflexes. REBOUNDER FOR TEE SIMULATION: Set up the QuickSwing PX4 Auto without the end dial. Position the rebounder directly below where the ball will be dropped from the QuickSwing PX4. The ball will bounce up directly upward to simulate hitting of a tee. While tee hitting is important for working on the mechanics of ball contact, the QuickSwing PX4 adds another layer to this. The ball dropping from the trainer forces batters to react to ball speed and path to give more of a challenge than an ordinary tee.

9 REBOUNDER FOR ANGLED SOFT TOSS: Set up the QuickSwing PX4 Auto without the end dial. Angle the rebounder to desired angle and position the rebounder so the higher side is below where the ball will drop from the QuickSwing PX4. As the ball hits the high side of the rebounder it will angle out for a soft toss style pitch. Soft toss pitching allows batters to work on their swing without the pressure of live pitching. Through repetition batters can work on perfecting swing mechanics for live pitching during game days. REBOUNDER FOR ANGLED TURNAROUND DOUBLE PLAY: Set up the QuickSwing PX4 Auto without the end dial. Place the rebounder at level height below where the ball will be released from the QuickSwing PX4. As the ball bounces off of the rebounder catch and throw for a turnaround double play simulation. To add difficulty, angle rebounder for a more challenging initial catch. Ideal for use with SKLZ practice nets. Through turnaround double play practice, athletes can work on their reaction and catch-to-throw transition times. By increasing the speed of the transition, players will be able to make more effective double plays and ultimately get more outs. SKLZ.com

10 PERFECT FOR PRACTICE WITH OTHER SKLZ PRODUCTS: AUTHENTIC SMALL-CIRCUMFERENCE BALL» 8 circumference baseball provides a smaller target to encourage batters to keep their eyes on the ball» Builds greater eye-hand coordination» Same construction as an official baseball, synthetic leather cover» 2.5 oz. weight» Available in a 6-pack (3 colors, 2 each) MSRP: $19.99 HEAVY DUTY QUICK ASSEMBLY MULTI-SPORT NET» The quickest way to get your game or practice going, sets up and breaks down in minutes» Strong-ply netting, heavy gauge nylon, and rigid support poles provide added sturdiness» Fits in included bag for easy carrying» Includes 4 Ground Stakes to secure goal into the ground» Lightweight, easy up and down net» Perfect for pitching or hitting practice» Includes removable pitching target MSRP 5ft: $99.99 MSRP 7ft: $ MULTI-SPORT TRAINING NET» Sturdy 7 multi-sport net» For indoor or outdoor practice» Sets up quickly and easily» Includes convenient carry bag MSRP 5ft: $59.99

11 90-DAY LIMITED WARRANTY QUICKSWING PX4 Pro Performance Sports (PPS) warrants to the original consumer purchaser of any PPS product it manufactures that the product will be free of defects in materials or workmanship for 90 days (unless specified in alternate warranties) from the date of purchase. If defective, and purchased from a retail store, return the product along with receipt to the retail store where the product was purchased. If the item was purchased from PPS, return the product along with proof of the date of purchase (i.e. the packing slip), postage prepaid to the address below for replacement consideration: Pro Performance Sports :: 5823 Newton Dr, Suite 130 :: Carlsbad, CA :: Attn: Returns This warranty does not cover damages resulting from accident, misuse, abuse or lost merchandise. Only valid in the USA. All returns sent to PPS require a Return Merchandise Authorization number (RMA). For returns to PPS and for all other Customer Service inquiries, please call toll free: Register your product at SKLZ.com to ensure warranty coverage, get new product information and special deals from SKLZ VIDEOS Become a fan on Facebook: facebook.com/sklzfans Follow us on DO YOU HAVE A WINNING SPORTS PRODUCT OR IDEA? Visit our website to learn how to submit a product application for consideration. It may become our next winning product! SKLZ.com Made in China 2011 Pro Performance Sports. All rights reserved. Unauthorized duplication is a violation of applicable laws. U.S. Patent # 6,974,396 SKLZ.com

12 rev.10/10