NONEL EZ DET. Properties. Technical Information. Nonelectric Blast Initiation System. Your Partner with TOTAL BLASTING SOLUTION

Transcription

1 NONE EZ DET Nonelectric Blast Initiation ystem Product Description Nonelectric Delay Detonator NONE EZDET units consist of a length of orange shock tube with a surface detonator attached to one end and an in-hole, High trength, detonator on the other. The surface detonator is inside a color-coded plastic EZ Connector block to facilitate easy connections to up to 6 shock tube leads. Easy-to-read, colorcoded delay tags display the delay number and nominal firingtime prominently. NONE EZDET units can be easily connected toone another to satisfy basic blast design requirements in construction, mining, and quarry operations. They can also be us ed in combination with NONE M, NONE EZT and/ or NONE TD detonators to satisfy complex blast design requirements and minimize inventory of initiation system components. Properties Net Explosive Content per units (Excluding hock Tube) Net Explosive Content per,000 m shock tube Hazardous hipping Description Detonator assemblies nonelectric, 1.4B, UN 0361 PG II 1.1B, UN 0360 PG II kg lbs kg lbs Nominal Time (msec) Nominal Time (msec) Connector Block Color 17 / / 500 Yellow 25 / / 500 Red 42 / / 500 White 25 / 3 Red I ee Product Disclaimer on next page. ( A) Your Partner with TOTA BATING OUTION

2 NONE EZ DET Nonelectric Blast Initiation ystem Application Recommendations AWAY select a NONE EZDET unit having more than enough tubing length to extend from the planned primer location in the borehole to the collar of the next hole. AWAY protect the plastic EZ Connector block and all shock tube leads from impact or damage during the loading and stemming operations. Use care when placing blasting mats and cover material on top of the blasting circuit. The EZ Connector block contains a detonator and is subject to detonation caused by abuse such as impact. hock tube which has been cut, ruptured or damaged may cause misfires. AWAY be sure that the shock tube(s) are securely inserted, one at a time, into the EZ Connector block. The head of the EZ Connector block should rise to accept the shock tube and return to a closed position with an audible click. AWAY ensure that individual shock tubes remain aligned side by side in the connector channel and do not cross one over the another on insertion. NEVER use NONE EZ DET units with detonating cord. The low strength surface detonator will not initiate detonating cord and may cause misfires. NEVER attempt to disassemble the delay detonator from the plastic EZ Connector block or use the detonator without the connector. NEVER place more than 6 shock tube leads into the plastic EZ Connector block. Misfires may result. NEVER pull, stretch, kink or put tension on shock tube such that the tube could break. NEVER splice NONE EZ DET shock tube together to extend between holes. Transportation, torage and Handling NONE EZDET must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations. For maximum shelf life (2 years), NONE EZ DET must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet Prevention of Accidents in the Use of Explosive Materials packed inside each case and the afety ibrary Publications of the Institute of Makers of Explosives. Packaging ength Case Type Quantity/ Case m ft 1.4B 1.1B 1.4B 1.1B ength rounded to nearest one-half meter. Case weight varies by length & delay; see case label for exact weight. Case Dimensions x 2 x 255 mm x 320 x 4 mm Product Disclaimer Tenaga Kimia dn Bhd, its subsidiaries and distributors disclaim any warranties with respect to this product, the safety or suitability thereof, or the results to be obtained, whether express or implied, INCUDING WITHOUT IMITATION, ANY IMPIED WARRANTY OF MERCHANTABIITY OR FITNE FOR A PARTICUAR PURPOE AND/OR OTHER WARRANTY. Buyers and users assume all risk, responsibility and liability whatsoever from any and all injuries (including death), losses, or damages to persons or property arising from the use of this product. Under no circumstances shall TKB, subsidiaries and distributors be liable for special, consequential or incidental damages or for anticipated loss of profits. TENAGA KIMIA DN BHD (26191-A) No. 8, Jalan 22/21, Damansara Jaya, Petaling Jaya, elangor Darul Ehsan, Malaysia. OR P.O. Box 11674, 504 Kuala umpur. Tel: Fax: tkb@tenagakimia.com Website:

3 NONE EZ T Nonelectric Trunkline Delay Detonators Product Description Nonelectric Trunkline Delay Detonators EZ T units consist of a length of yellow shock tube, with a surface detonator attached to one end and the other end sealed. The detonator is housed in a plastic EZ Connector block which facilitates easy connection to shock tube. A white J-hook is affixed near the sealed end. Easy-to-read, color-coded delay tags display the delay number and nominal firing time prominently. NONE EZ T detonators are designed for use with NONE M and NONE EZ DET units to provide effective and accurate surface timing between blastholes and/or rows of blastholes in surface and underground blasting designs. Properties Net Explosive Content per units (Excluding hock Tube) Hazardous hipping Description Detonator assemblies nonelectric, 1.4B, UN 0361 PG II 1.1B, UN 0360 PG II kg lbs Net Explosive Content per,000 m shock tube kg lbs Delay Time (msec) Connector Block Color 17 Yellow 25 Red 42 White 67 Black Black I ee Product Disclaimer on next page. ( A) Your Partner with TOTA BATING OUTION

4 NONE EZ T Nonelectric Blast Initiation ystem Application Recommendations AWAY be sure that the shock tube(s) are securely inserted, one at a time, into the plastic EZ connector. The head of the connector block should rise to accept the tube, and return to a closed position with an audible click. AWAY ensure that the individual shock tubes remain aligned side by side in the EZ connector channel and do not cross over one another during insertion. AWAY protect the plastic EZ connector and all shock tube leads from impact or damage. Use care when placing blasting mats and cover material on top of the blasting circuit. The EZ connector contains a detonator and is subject to detonation caused by abuse such as impact. hock tube which has been cut, ruptured or damaged may cause misfires. Transportation, torage and Handling NONE EZT must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations. For maximum shelf life (2 years), NONE EZT must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet Prevention of Accidents in the Use of Explosive Materials packed inside each case and the afety ibrary Publications of the Institute of Makers of Explosives. NEVER use NONE EZT detonators with detonating cord. The low strength surface detonator will not initiate detonating cord. NEVER attempt to disassemble the delay detonator from the EZ connector block or use the detonator without the connector. NEVER place more than 6 shock tube leads into an EZ connector block. Misfires may result. Packaging ength Case Type Quantity/ Case m ft 1.4B 1.1B 1.4B 1.1B ength rounded to nearest one-half meter. Case weight varies by length & delay; see case label for exact weight. Case Dimensions x 2 x 255 mm x 320 x 4 mm Product Disclaimer Tenaga Kimia dn Bhd, its subsidiaries and distributors disclaim any warranties with respect to this product, the safety or suitability thereof, or the results to be obtained, whether express or implied, INCUDING WITHOUT IMITATION, ANY IMPIED WARRANTY OF MERCHANTABIITY OR FITNE FOR A PARTICUAR PURPOE AND/OR OTHER WARRANTY. Buyers and users assume all risk, responsibility and liability whatsoever from any and all injuries (including death), losses, or damages to persons or property arising from the use of this product. Under no circumstances shall TKB, subsidiaries and distributors be liable for special, consequential or incidental damages or for anticipated loss of profits. TENAGA KIMIA DN BHD (26191-A) No. 8, Jalan 22/21, Damansara Jaya, Petaling Jaya, elangor Darul Ehsan, Malaysia. OR P.O. Box 11674, 504 Kuala umpur. Tel: Fax: tkb@tenagakimia.com Website:

5 NONE ead ine Nonelectric hock Tube Product Description Nonelectric hock Tube NONE ead ine is a small diameter, threelayer plastic tube coated on the innermost wall with a reactive explosive compound. When initiated, nonelectric shock tube propagates a low energy signal, similar to a dust explosion, at approximately 0 m/sec (6,500 ft/sec) along the tube s length with minimal disturbance to the outside of the tube. The signal is transmitted from one nonelectric shock tube to another through field-assembled splices. NONE ead ine provides maximum flexibility to the blaster in choosing a position of safety from which to initiate nonelectric blast rounds in either underground or surface applications. NONE ead ine is the only NONE product that can be cut and spliced into a NONE detonator product to construct a custom length nonelectric starter assembly. Properties ength rounded to nearest one-half meter. ee case label for exact case weight. Nonel shock tube with Wire ock Terminations or Ultrasonically ealed Terminations Hazardous hipping Description Not regulated as an Explosive, UN0000 (Reference number EX1197A) ength m ft Case pools / Case Case Dimensions x 350 x mm x 400 x 250 mm I ee Product Disclaimer on next page. ( A) Your Partner with TOTA BATING OUTION

6 NONE ead ine Nonelectric hock Tube Application Recommendations AWAY splice NONE ead ine to NONE EZT nonelectric trunkline delay detonators, NONE EZDET nonelectric blast initiation system, NONE TD or NONE starter detonators to make-up the nonelectric starter assembly when using NONE ead ine as the primary initiator for nonelectric blast rounds. AWAY trim at least 3 m [10 ft] of tubing before inserting into a nonelectric shock tube starting device or whenever dirt and/or moisture may have compromised the open tube ends before making a splice connection. AWAY replace the plastic tube closure over the open end of any NONE ead ine that remains on the spool and is intended to be used to make up another nonelectric starter assembly. AWAY make the final hook-up of the nonelectric starter assembly to the blast round only after all equipment and nonessential personnel are clear of the blast area. AWAY unspool NONE ead ine by hand if the starter assembly has been spliced to it and is attached to the blast round. AWAY keep any NONE ead ine tube ends sealed and free from dirt and moisture since dirt or moisture in the shock tube may cause a misfire. AWAY replace the NONE ead ine if it is damaged. When making a nonelectric starter assembly using NONE ead ine, AWAY remove the plastic tube closure and save for later use. plice two freshly-cut ends of nonelectric shock tube together (one from the NONE ead ine and the other from the nonelectric detonator) by inserting them into opposite ends of the plastic connector sleeve and pushing them toward one another until they are both at least ½ cm (¼ in) in the splice. NEVER use NONE ead ine for in-hole use. NONE ead ine is for use outside the borehole only. NEVER remove the plastic tube closure from the NONE ead ine shock tube until just before splicing. NEVER attempt to knot different lengths of shock tube together. hock tube will not initiate itself through knot connections. It must be spliced NEVER attach the starter assembly to the blast round until after the ead ine deployment is complete whenever NONE ead ine is to be unspooled by any method other than by hand NEVER run over NONE ead ine with equipment. This may damage the shock tube and may cause a misfire. Transportation, torage and Handling NONE ead ine must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations. For maximum shelf life (2 years), NONE ead ine must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet Prevention of Accidents in the Use of Explosive Materials packed inside each case and the afety ibrary Publications of the Institute of Makers of Explosives. Product Disclaimer Tenaga Kimia dn Bhd, its subsidiaries and distributors disclaim any warranties with respect to this product, the safety or suitability thereof, or the results to be obtained, whether express or implied, INCUDING WITHOUT IMITATION, ANY IMPIED WARRANTY OF MERCHANTABIITY OR FITNE FOR A PARTICUAR PURPOE AND/OR OTHER WARRANTY. Buyers and users assume all risk, responsibility and liability whatsoever from any and all injuries (including death), losses, or damages to persons or property arising from the use of this product. Under no circumstances shall TKB, subsidiaries and distributors be liable for special, consequential or incidental damages or for anticipated loss of profits. TENAGA KIMIA DN BHD (26191-A) No. 8, Jalan 22/21, Damansara Jaya, Petaling Jaya, elangor Darul Ehsan, Malaysia. OR P.O. Box 11674, 504 Kuala umpur. Tel: Fax: tkb@tenagakimia.com Website:

7 NONE P Nonelectric ong Period Delay Detonator Product Description Nonelectric ong Period Delay Detonator NONE P units consist of a length of yellow shock tube with a High trength detonator attached to one end and the other end sealed. A J-hook is affixed near the sealed end, providing easy means of connection to detonating cord. Easy-to-read, color-coded delay tags display the delay number and nominal firing time prominently. NONE P units are designed to provide in-hole delay time for underground (non-coal) and special construction blasting applications that require long delay times to improve relief and fragmentation (such as drift development, raise and shaft work, as well as slope and tunnel blast rounds). They are typically used with detonating cord but can also be used with NONE EZT detonators for additional timing flexibility. Properties Net Explosive Content per units (Excluding hock Tube) Hazardous hipping Description Detonator assemblies nonelectric, 1.4B, UN 0361 PG II 1.1B, UN 0360 PG II kg lbs Net Explosive Content per,000 m shock tube kg lbs Period / Delay Time (msec) Delay Tag Color Period / Delay Time (msec) Connector Block Color 0 /17 Orange 10 / 4600 Yellow 1 / Yellow 11 / 5500 t Blue 2 / 400 Green 12 / 6400 Purple 3 / 600 t Blue 13 / 7400 Tan 4 / 0 Tan 14 / 8500 Red 5 / 1400 Gray 15 / 9600 Gray 6 / 1800 Blue 7 / 2400 Pink 8 / 00 White 9 / 3800 Orange I ee Product Disclaimer on next page. ( A) Your Partner with TOTA BATING OUTION

8 NONE P Nonelectric ong Period Delay Detonator Application Recommendations AWAY use the plastic J-hook when using a detonating cord trunkline to tie-in NONE P nonelectric delay detonators. A minimum 3 g/m (18 gr/ft) detonating cord trunkline is required for use with the J-hook. AWAY ensure the shock tube is connected at right angles to the detonating cord trunkline and that the shock tube leads returning to the hole collar do not cross over or lay near any detonating cord trunkline. If the detonating cord touches the shock tube or is closer than 6 inches (15 cm), the shock tube may be damaged and misfires may result. AWAY connect detonating cord using approved knots and tight connections. Place detonating cord hook-ups in closed loops and use with cross-ties. AWAY make sure that no shock tube or detonating cord can be pinched between the the basket, platform or boom and the face, ribs, back or floor. Rupturing or damaging shock tube or detonating cord may cause misfires. Where NONE P detonator lead lengths permit, bunch blasting provides the most efficient means of hooking up rounds in drifts, tunnels, shafts and raises. NEVER put more than 20 NONE P delays per bunch. A minimum 5 g/m (25 gr/ft) detonating cord is required for bunch blasting. NEVER cut or trim seals from the shock tube of a NONE P delay. If shock tubing is cut or is suspected of being cut or damaged during loading, AWAY reprime the borehole using a new unit of the same delay period. NEVER drive any equipment over the shock tube or detonating cord. Whenever charging from a maneuverable basket, platform or boom, AWAY make sure that no shock tube or detonating cord is entangled or can become entangled. Transportation, torage and Handling NONE P must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations. For maximum shelf life (2 years), NONE P must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old.for recommended good practices in transporting, storing, handling and using this product, see the booklet Prevention of Accidents in the Use of Explosive Materials packed inside each case and the afety ibrary Publications of the Institute of Makers of Explosives. Packaging ength m ft Case Type Coil Type Quantity/ Case 1.4B 1.1B 1.4B 1.1B ength rounded to nearest one-half meter. Case weight varies by length & delay; see case label for exact weight. Case Dimensions x 2 x 255 mm x 320 x 4 mm Product Disclaimer Tenaga Kimia dn Bhd, its subsidiaries and distributors disclaim any warranties with respect to this product, the safety or suitability thereof, or the results to be obtained, whether express or implied, INCUDING WITHOUT IMITATION, ANY IMPIED WARRANTY OF MERCHANTABIITY OR FITNE FOR A PARTICUAR PURPOE AND/OR OTHER WARRANTY. Buyers and users assume all risk, responsibility and liability whatsoever from any and all injuries (including death), losses, or damages to persons or property arising from the use of this product. Under no circumstances shall TKB, subsidiaries and distributors be liable for special, consequential or incidental damages or for anticipated loss of profits. TENAGA KIMIA DN BHD (26191-A) No. 8, Jalan 22/21, Damansara Jaya, Petaling Jaya, elangor Darul Ehsan, Malaysia. OR P.O. Box 11674, 504 Kuala umpur. Tel: Fax: tkb@tenagakimia.com Website:

9 NONE M Nonelectric Millisecond Delay Detonator Product Description Nonelectric Millisecond Delay Detonator NONE M unit consists of a length of orange shock tube with a High trength detonator attached to one end and the other end sealed. A white J-hook is affixed near the sealed end, providing easy means of connection to detonating cord. Easy-to-read, colorcoded delay tags display the delay number and nominal firing time prominently. NONE M is designed to provide in-hole time for underground (non-coal) and surface blast applications in the mining, quarry and construction industries and can be used in combination with a detonating cord trunkline, NONE EZT, NONE EZDET and/or NONE TD detonators for maximum timing flexibility Properties Net Explosive Content per units (Excluding hock Tube) Hazardous hipping Description Detonator assemblies nonelectric, 1.4B, UN 0361 PG II 1.1B, UN 0360 PG II kg lbs Net Explosive Content per,000 m shock tube kg lbs Period / Delay Time (msec) Delay Tag Color Period / Delay Time (msec) Connector Block Color 1 / 25 Red 9 / 250 Red 2 / 50 Tan 9½ / 2 White 3 / Green 10 / 0 Tan 4 / Blue 10½ / 325 White 5 / 125 Orange 11 / 350 Green 6 / Purple 11½ / 3 White 7 / 1 Gray 12 / 400 Blue 8 / t Blue 13 / 450 Orange 8½ / 225 White 14 / 500 Purple I ee Product Disclaimer on next page. ( A) Your Partner with TOTA BATING OUTION

10 NONE M Application Recommendations AWAY use the plastic J-hook when using a detonating cord trunkline to initiate a NONE M unit. A minimum 3 g/m (15 gr/ft) detonating cord qualified for surface use is required for use with the J-hook. AWAY make sure the shock tube is connected to the J-hook and leads back to the hole collar at right angles to the detonating cord trunkline. Transportation, torage and Handling NONE M must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations. For maximum shelf life (2 years), NONE M must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet Prevention of Accidents in the Use of Explosive Materials packed inside each case and the afety ibrary Publications of the Institute of Makers of Explosives. Packaging ength m ft Case Type Coil Type Quantity/ Case 1.4B 1.1B 1.4B 1.1B ariat ariat ength rounded to nearest one-half meter. Case weight varies by length & delay; see case label for exact weight. Case Dimensions x 2 x 255 mm x 320 x 4 mm Product Disclaimer Tenaga Kimia dn Bhd, its subsidiaries and distributors disclaim any warranties with respect to this product, the safety or suitability thereof, or the results to be obtained, whether express or implied, INCUDING WITHOUT IMITATION, ANY IMPIED WARRANTY OF MERCHANTABIITY OR FITNE FOR A PARTICUAR PURPOE AND/OR OTHER WARRANTY. Buyers and users assume all risk, responsibility and liability whatsoever from any and all injuries (including death), losses, or damages to persons or property arising from the use of this product. Under no circumstances shall TKB, subsidiaries and distributors be liable for special, consequential or incidental damages or for anticipated loss of profits. TENAGA KIMIA DN BHD (26191-A) No. 8, Jalan 22/21, Damansara Jaya, Petaling Jaya, elangor Darul Ehsan, Malaysia. OR P.O. Box 11674, 504 Kuala umpur. Tel: Fax: tkb@tenagakimia.com Website:

11 NONE tarter Nonelectric hock Tube & Detonator Assembly Product Description Nonelectric hock Tube & Detonator Assembly NONE tarter is consist of a spooled length of yellow shock tube with a tandard (#8) detonator attached to one end and the other end sealed. The detonator is housed in a plastic bunch block which facilitates easy connection to both shock tube and detonating cord. NONE tarter is designed to provide controlled, nonelectric initiation of surface and underground blast rounds. Properties Net Explosive Content per units (Excluding hock Tube) kg lbs Net Explosive Content per,000 m shock tube kg lbs Hazardous hipping Description Detonator Assemblies nonelectric, 1.4B, UN 0361 PG II I ee Product Disclaimer on next page. ( A) Your Partner with TOTA BATING OUTION

12 NONE tarter Application Recommendations AWAY trim excess lengths of detonating cord from bunch block. Detonating cord tails lying across outgoing trunkline can interfere with normal function. AWAY use NONE ead ine to splice onto the NONE tarter unit to make up a custom length nonelectric starter assembly whenever the length of NONE tarter unit is not sufficient to position the blaster safely. AWAY use the plastic connector sleeves packaged in each NONE ead ine case to make a reliable splice connection to NONE tarter unit. AWAY hook the NONE tarter bunch block to the blast round after all equipment and non-essential personnel are clear of the blast area. AWAY unspool NONE tarter unit by hand if the bunch block has been attached to the blast round. AWAY place the bunch block so the lid is face down and cover the bunch block with drill cuttings or other inert material to help prevent shrapnel cut-off after attaching the bunch block to detonating cord or shock tube. AWAY replace the NONE tarter if it is damaged. When using NONE tarter detonators with a detonating cord trunkline, AWAY place the detonating cord in the bunch block parallel to the detonator with the detonator pointing in the desired direction of initiation. NEVER attempt to initiate more than eight (8) NONE shock tubes or one (1) detonating cord trunkline with the bunch block. Misfires may result. NEVER place detonating cord and shock tube in the same NONE tarter bunch block. Misfires may result. NEVER attach the NONE tarter bunch block to the blast round until after the NONE tarter shock tube deployment is complete whenever a NONE tarter unit is to be unspooled by any method other than by hand. NEVER run over NONE tarter detonators with equipment. This may damage the shock tube and may cause a misfire. Transportation, torage and Handling NONE tarter must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations. For maximum shelf life (2 years), NONE tarter must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet Prevention of Accidents in the Use of Explosive Materials packed inside each case and the afety ibrary Publications of the Institute of Makers of Explosives. Packaging ength m ft Case Type Coil Type pools/ Case 1.4B 1.4B ength rounded to nearest one-half meter. ee case label for exact case weight. Case Dimensions x 350 x mm x 400 x 250 mm Product Disclaimer Tenaga Kimia dn Bhd, its subsidiaries and distributors disclaim any warranties with respect to this product, the safety or suitability thereof, or the results to be obtained, whether express or implied, INCUDING WITHOUT IMITATION, ANY IMPIED WARRANTY OF MERCHANTABIITY OR FITNE FOR A PARTICUAR PURPOE AND/OR OTHER WARRANTY. Buyers and users assume all risk, responsibility and liability whatsoever from any and all injuries (including death), losses, or damages to persons or property arising from the use of this product. Under no circumstances shall TKB, subsidiaries and distributors be liable for special, consequential or incidental damages or for anticipated loss of profits. TENAGA KIMIA DN BHD (26191-A) No. 8, Jalan 22/21, Damansara Jaya, Petaling Jaya, elangor Darul Ehsan, Malaysia. OR P.O. Box 11674, 504 Kuala umpur. Tel: Fax: tkb@tenagakimia.com Website:

13 NONE TD Nonelectric Trunkline Delay Detonator Product Description Nonelectric Trunkline Delay Detonator NONE TD unit consists of a length of yellow shock tube with a tandard (#8) detonator attached to one end and the other end sealed. The detonator is housed in a plastic bunch block which facilitates easy connection to both shock tube and detonating cord. A white J-hook is affixed near the sealed end providing easy means of connection to detonating cord. Easy to read, color-coded delay tags display the delay number and nominal firing time prominently. The plastic bunch block has the capacity to initiate up to eight (8) shock tubes or one (1) detonating cord downline. NONE TD units are designed for use with NONE M, NONE EZDET and detonating cord downlines to provide effective and accurate surface timing between blastholes and/or rows of blastholes in surface and underground blasting designs. Properties Net Explosive Content per units (Excluding hock Tube) kg lbs Net Explosive Content per,000 m shock tube kg lbs Hazardous hipping Description Detonator assemblies nonelectric, 1.4B, UN 0361 PG II Period / Delay Time (msec) Connector Block Color 17 Yellow 25 Red 42 White 67 Black Black I ee Product Disclaimer on next page. ( A) Your Partner with TOTA BATING OUTION

14 NONE TD Nonelectric Trunkline Delay Detonator Application Recommendations AWAY attach the shock tubes of NONE TD units leading to other holes to the detonating cord using the J-hook. Attach the J-hook to the detonating cord downline between the previous bunch block and the collar of the blasthole leaving at least cm (12 in) between the adjacent bunch block. AWAY leave 13 cm (5 in) between the J-hook and any detonating cord knot. AWAY place the bunch block so the lid is face down and cover the bunch block with drill cuttings or other inert material to help prevent shrapnel cut-off after attaching the bunch block to detonating cord or shock tube. AWAY ensure that outgoing shock tubes or detonating cords lead straight away from the NONE TD unit bunch block for at least cm (12 in). When using NONE TD units with a detonating cord downline, AWAY attach the bunch block to the tail of the detonating cord downline extending out from the hole to be initiated. Place the detonating cord in the bunch block with the detonator pointing in the desired direction of initiation. Packaging ength m ft Case Type 1.4B Coil Type Quantity/ Case 1.4B 125 Ensure that outgoing shock tubes connect at right angles to the detonating cord and that the lid is tightly closed. NEVER loop shock tube near the bunch block or detonating cord. NEVER bend the tubes around the end of the bunch block, back over the top of the block or allow the outgoing shock tube trunklines or downlines to loop back near the bunch block. NEVER place both detonating cord and shock tube in the same NONE TD bunch block. Misfires may result. Place all shock tube downlines and outgoing trunkline leads in the bunch block with the detonator pointing in the desired direction of initiation. Transportation, torage and Handling NONE TD must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations. For maximum shelf life (2 years), NONE TD must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet Prevention of Accidents in the Use of Explosive Materials packed inside each case and the afety ibrary Publications of the Institute of Makers of Explosives. ength rounded to nearest one-half meter. Case weight varies by length & delay; see case label for exact weight. Case Dimensions x 320 x 4 mm Product Disclaimer Tenaga Kimia dn Bhd, its subsidiaries and distributors disclaim any warranties with respect to this product, the safety or suitability thereof, or the results to be obtained, whether express or implied, INCUDING WITHOUT IMITATION, ANY IMPIED WARRANTY OF MERCHANTABIITY OR FITNE FOR A PARTICUAR PURPOE AND/OR OTHER WARRANTY. Buyers and users assume all risk, responsibility and liability whatsoever from any and all injuries (including death), losses, or damages to persons or property arising from the use of this product. Under no circumstances shall TKB, subsidiaries and distributors be liable for special, consequential or incidental damages or for anticipated loss of profits. TENAGA KIMIA DN BHD (26191-A) No. 8, Jalan 22/21, Damansara Jaya, Petaling Jaya, elangor Darul Ehsan, Malaysia. OR P.O. Box 11674, 504 Kuala umpur. Tel: Fax: tkb@tenagakimia.com Website:

15 marthot marthot Detonator To hook up, the male connector of one unit simply snaps into the female connector of the next unit, and so on, along a row. marthot Base tation Used to initiate the blast remotely from a safe distance. The PIN protected martkey must be docked in the Base tation to arm and fire the shot. marthot Bench Box The receiver unit that allows remote firing via radio frequency from the Base tation, passing the signal onto the detonators in order to initialise the blast. Product Description marthot is the latest advancement in pricise electronic initiation system. The marthot system offers innovative features including wireless remote blasting and complete timing flexibility. pecialised waterproof and dirt displacing connectors ensure quick, easy and reliable connections, and prevent leakage. tring tarter Connected between the blast and the Bench Box to interface 2-wire with 4-wire communication. It will also assist in identifying any faults. End Plug Connected to the end of each string to indicate the end of a string to the control equipment marthot Tagger Hand-held unit to test and assign timings to individual detonators and defines the hole configuration. marthot Detonators Downline x urface ength Metres Units per case Packaging Dimensions hipping Classification 10 x x 215 x 245mm x x x x x x x 215 x 245mm 480 x 215 x 245mm 480 x 215 x 245mm 480 x 215 x 245mm 480 x 215 x 245mm 480 x 215 x 245mm I ee Product Disclaimer on next page. ( A) Your Partner with TOTA BATING OUTION

16 marthot marthot Accessories marthot Base tation marthot Bench Box tring tarters & End Plugs mart Keys Tagger ite Connection Block and Cable Units per case Dimensions of Packaging (millimetres) 523 x 3 x 260mm 523 x 3 x 260mm x 165 x 92mm 146 x 86 x 38mm 0 x 250 x 140mm x 165 x 92mm Properties ystem imits Maximum Total Delay Time milliseconds Maximum Number of Detonators 1600* with expander module 24000* ead-in ength (wireless) 00m* ead-in ength (wire) 0m* Maximum In-hole ead ength 80m / 260ft *Dependant on shot layout, please refer to training manual before use Detonator Dynamic hock Resistance >12,000psi 500ns pulse width ED Resistance Passes EN RF Immunity Passes CEN T Detonator hell Copper Detonator trength 8D (I.M.E.:#12) trength Base Charge PETN Net Explosive Quantity (NEQ) 0,1KG ( lbs.) per detonators Timing Fully programmable and Autoprogrammable Connector Rugged, water resistant Tensile trength >250 N / 53 lbs Detonator hell Marking Dangerous - Blasting Cap - Explosive Danger - Detonator - Explosif Transportation, torage and Handling marthot must be transported, stored, handled and used in conformity with all federal, state, provincial and local laws and regulations. For maximum shelf life (2 years), marthot must be stored in a cool, dry, well ventilated magazine. Explosive inventory should be rotated. Avoid using new materials before the old. For recommended good practices in transporting, storing, handling and using this product, see the booklet Prevention of Accidents in the Use of Explosive Materials packed inside each case and the afety ibrary Publications of the Institute of Makers of Explosives. Packaging UN hipping Classification 1.4 Detonator Configurations Coil Cable Colour Green with a coloured stripe Product Disclaimer Tenaga Kimia dn Bhd, its subsidiaries and distributors disclaim any warranties with respect to this product, the safety or suitability thereof, or the results to be obtained, whether express or implied, INCUDING WITHOUT IMITATION, ANY IMPIED WARRANTY OF MERCHANTABIITY OR FITNE FOR A PARTICUAR PURPOE AND/OR OTHER WARRANTY. Buyers and users assume all risk, responsibility and liability whatsoever from any and all injuries (including death), losses, or damages to persons or property arising from the use of this product. Under no circumstances shall TKB, subsidiaries and distributors be liable for special, consequential or incidental damages or for anticipated loss of profits. TENAGA KIMIA DN BHD (26191-A) No. 8, Jalan 22/21, Damansara Jaya, Petaling Jaya, elangor Darul Ehsan, Malaysia. OR P.O. Box 11674, 504 Kuala umpur. Tel: Fax: tkb@tenagakimia.com Website: