OPTIMISING CHASSIS ALIGNMENT USING VEHICLE SENSORS

Size: px
Start display at page:

Download "OPTIMISING CHASSIS ALIGNMENT USING VEHICLE SENSORS"

Transcription

1 Link: SPECIAL ASSEMBLY OPTIMISING CHASSIS ALIGNMENT USING VEHICLE SENSORS The commissioning processes at the End-of-Line (EOL) of vehicle final assembly are characterised by a large amount of manual and therefore cost-intensive work. In a cooperation project with RWTH Aachen University and ZeMA Saarbrücken, Daimler is developing a chassis alignment process that can be executed without the manual insertion and extraction of a steering wheel balancer at the wheel alignment station. 58

2 AUTHORS DIPL.-WIRT.-ING. CHRISTIAN JANSSEN is Research Assistant at the Laboratory for Machine Tools and Production Engineering (WZL) at RWTH Aachen University (Germany). DR. RER. NAT. HARTMUT PRESTING is Head of Process Analysis and Adjustment Technologies in Production Planning Mercedes-Benz Cars at Daimler AG in Ulm (Germany). DR.-ING. KLAUS JOSTSCHULTE is Head of Validation Technologies in Production Planning Mercedes-Benz Cars at Daimler AG in Ulm (Germany). PROF. DR.-ING. RAINER MÜLLER is Scientific Director of ZeMA ggmbh in Saarbrücken (Germany). OPTIMISATION POTENTIAL IN CHASSIS ALIGNMENT Car production is subject to a great deal of competitive pressure between the manufacturers, therefore leading to a constant need to cut costs. One effective way of doing this is to optimise the production processes [1]. Particularly at the End-of-Line (EOL) of vehicle final assembly, the possible savings are high due to the large number of well-trained workers. At the End-of-Line of final assembly, the vehicles are commissioned, e. g. single systems and functions are checked and/or adjusted. For example, the parking brake and the service brake are checked on the rolling road, while the main headlights and driving assistance systems are often adjusted at a wheel alignment station. ❶ shows an example of a wheel alignment station. After the vehicle is brought to the stand, the wheel geometry (e. g. toe angle, camber angle etc.) is measured with the aid of a laser measuring system and the steering wheel angle is detected with a steering wheel balancer. The data are used to adjust the chassis automatically to the nominal values or the nominal range. In order to increase the efficiency of the EOL, the current project is focusing on increasing the level of automation. Not only the chassis alignment process but also the adjustment process of the main headlights and the alignment of the optional radar sensor and camera have been automated so far. One process that still has to be automated, in order to achieve a fully automated wheel alignment station, is the detection of the steering wheel angle or the insertion of a steering wheel balancer. The current situation is that the steering wheel balancer is mounted on the steering wheel and removed manually. The goal of this project is to detect the current steering wheel angle at the wheel alignment station fully automatically without any manual work at all. DEVELOPMENT OF AN EFFICIENT CHASSIS ALIGNMENT PROCESS In order to develop a chassis alignment process that can be executed without any manual labour for the detection of the steering wheel angle, and to implement this process in the production process, a method has been employed, which has been developed as a part of a dissertation at the chair of assembly systems from the RWTH Aachen to design complex commissioning processes, ❷. In this context, commissioning refers to testing and adjustment processes. Although the different modules of this method are performed in a stringent order, an iterative approach may be necessary due to interdependencies between the modules. For example, when analysing the products, a rough knowledge of the production processes can be beneficial. The practical application of this method is explained in more detail below. PRODUCT ANALYSIS Within the first module, the expectations of the customer are analysed. Furthermore, it examines how the current products technically fulfill the customer s requirements. With the aid of the key characteristic (KC) flow down, components that have a great influence on the fulfillment of the customer s expectations are identified. A top-down approach is em- ❶ Wheel alignment station at the end-of-line of vehicle final assembly 04I2013 Volume

3 SPECIAL ASSEMBLY ❷ Method to design complex commissioning processes ployed in order to link the customer s requirements with the assembly group and the elements and their characteristics [2]. The current steering wheel angle is continuously measured with the help of the steering wheel balancer in order to adjust the wheel alignment in such a way that the steering wheel is straight when the vehicle is moving straight ahead, which means that the direction of travel of the front axle corresponds to the wheel alignment geometry, ❸. This condition is required by the customers. In premium segment vehicles in particular, failure to fulfill this expectation will lead to customer complaints. ❹ shows the KC flow down that is used to break down the customer requirements to the component level. α RR α RL Longitudinal axis of the vehicle (and parallel lines) Thrust line (and parallel lines) Wheel center planes α RL : Toe angle rear left α RR : Toe angle rear right α FL : Toe angle front left α FR : Toe angle front right ❸ Wheel alignment geometry and steering system 60 The customer s requirement establishes a direct connection between the vehicle s driving direction and the steering wheel angle. The vehicle s driving direction is predominantly influenced by the wheel alignment, in particular the toe angle values of the wheels at the rear and front axle. While DIN defines the toe angle value of the rear axle as the angle between the wheel centre plane and the longitudinal axis of the vehicle (determined by the middle of the front and rear axle), the toe angle value of the front axle is described in DIN , relative to the thrust line, 3 [3, 4]. The thrust line is defined by the centre planes of the wheels of the rear axle [4]. α FL α FR Steering wheel Steering column Steering track rod Adjustment mechanism Picture source: ZF The toe angles of the front axle can be changed via the adjustment mechanisms located at the steering track rod on the left or right hand side. These adjustment mechanisms also allow an adjustment of the steering wheel angle relative to the toe angles of the front axle. As shown in 3, a steering wheel angle that is not zero leads to a virtual toe angle, which has to be compensated for. Therefore, the steering wheel angle has to be measured continuously. With the aid of the compensation of the current steering wheel angle, the toe angles of the front axle ( VL, VR ) can be determined and adjusted. The components and parts that have been identified in the KC flow down constitute the basis for the following analyses. In order to be able to draw a conclusion about the influence on the customer s requirements, the identified assemblies and components have to be examined. One specific assembly group that makes it rather difficult to fulfill the customer s requirements is, for example, the steering system. Due to their design, vehicle steering systems have a tolerance. This characteristic leads to the fact that one steering wheel angle goes with different toe angles or different driving directions (calculated on the basis of the toe angles of the front axle). ❺ shows a strongly simplified result of an experiment in which the steering wheel was rotated multiple times clockwise and anti-clockwise. As the diagram shows, the change of direction leads to a hysteresis curve. Knowledge of this product characteristic is relevant when evaluating the reproducibility of the results of measuring process. An example of a component that makes a positive contribution to the objective of the project is the steering angle sensor [5]. Steering angle sensors are now available that can measure the current steering wheel angle with a relatively high resolution. In order to evaluate the potential of these sensors, several vehicles were examined in the production process with regard to absolute and repeat accuracy. Since vehicles are products that are subject to continuous change, product analysis focuses not only on the status quo but also on possible future changes. In the presented use case, steer-by-wire systems, for example, could have ramifications on the wheel alignment and accordingly on the measurement of the

4 steering wheel angle at the wheel alignment station. PRODUCTION ANALYSIS Customer s requirement Steering wheel level while vehicle moving straight ahead In the second module, the framework conditions of the production process are analysed. This refers not only to the production processes that are relevant for fulfilling the customer s requirements but also to the manufacturing resources that are required in order to execute these processes. The wheel alignment process in this use case starts by automatically conveying the vehicle into the wheel alignment station. After the vehicle is centred in the wheel alignment station, the steering wheel balancer is mounted onto the steering wheel and then fixed to the windscreen. Subsequently, the wheel geometry (for example toe and camber angle) is measured by a laser system. On the basis of the continuously measured wheel geometry and steering wheel angle, the front toe angle is adjusted by an automated toe angle adjustment system. Since the steering wheel angle is measured and compensated for, this ensures that the adjustment of the angle is accurate even when the steering wheel is turned. The process analysis yields several manufacturing resources (in particular laser measurement systems, steering wheel balancer and adjustment mechanisms) that have an influence on the customer s requirements (for example measuring accuracy, resolution and minimum possible adjustment steps). In order to be able to draw a conclusion concerning the main influences of the manufacturing resources, their characteristics were examined by means of tolerance analysis. In addition to the wheel alignment process, the assembly and commissioning processes of the steering angle sensor were analysed to estimate the improvement potential of the steering wheel sensor. Product Assembly group Component Wheel geometry (e. g. toe, camber) Rear axle vehicle steering wheel sensor is one possible solution for achieving a fully automated measurement of the steering wheel angle at the wheel alignment station, ❻. A comparison of the results of the product analysis with the results of the production analysis shows that the steering wheel sensor and the steering wheel balancer have a similar repeat accuracy. However, the absolute accuracy of the steering wheel sensor in the observed assembly process is not yet high enough. This challenge can be met, for example, by calibrating the steering wheel sensor, which requires less effort than mounting and dismounting a steering wheel balancer by hand at the wheel alignment station. Another challenge is the fixation of the steering wheel in the wheel alignment station, because, if the steering wheel ❹ Key characteristic flow down of customer s requirements Steering wheel angle [ ] Steering wheel tolerance center Adjustment mechanism sensor is used to detect the steering wheel angle, there is no steering wheel balancer which could be used to fix the steering wheel. With the assumption that a fixation of the steering wheel is not necessary, the developed process plans that the steering wheel sensor is calibrated after its assembly and prior to the wheel alignment station. After the calibration of the sensor, the chassis can be adjusted according to the values gained from the measured data of the steering wheel sensor. IMPLEMENTATION OF THE PROCESS Steering system Front axle Steering wheel Steering wheel sensor In the fourth module, a stepwise secured implementation of the process takes place in the production process. In this use case, there are four stages with the following goals: DEVELOPMENT OF THE COMMISSIONING PROCESS Front axle driving direction [ ] Following the product analysis and the production analysis, the third module deals with the development of a commissioning process. As mentioned above in the product analysis, utilisation of the Steering wheel tolerance ❺ Schematic diagram of the hysteresis curve of steering systems 04I2013 Volume

5 SPECIAL ASSEMBLY ❻ Measurement of the steering wheel angle via the steering wheel sensor : 1 st stage: showing that the fixation of the steering wheel balancer at the wheel alignment station is not needed : 2 nd stage: calibration of the steering wheel sensor prior to the wheel alignment station : 3 rd stage: adjustment of the chassis based on the measurement of the steering wheel sensor : 4 th stage: removing the steering wheel balancer. During the first stage, it was shown by experiments in the production area that wheel alignment with an unfixed steering wheel balancer is at least as accurate as adjustment with a fixed steering wheel balancer. Furthermore, in the second stage, it was proven that the required absolute accuracy for adjusting the chassis could be achieved. The third and fourth stages have not been executed yet, but the results gained so far indicate that integration of these two stages into the production process will also be successful. REFERENCES [1] PriceWaterhouseCoopers AG: Kostenmanagement in der Automobilindustrie. Bestandsaufnahme und Zukunftspotenziale. Studie 2007 [2] Whitney, D. E.: Mechanical Assemblies. Their Design, Manufacture and Role in Product Development. Oxford University Press, New York, 2004 [3] Norm DIN (Januar 1994). Fahrzeugdynamik und Fahrverhalten. Begriffe [4] Norm DIN (August 1992). Straßenfahrzeuge Fahrwerkvermessung. Anzugebende Fahrwerkdaten, Messbedingungen [5] Schutzrecht DE ( ). Bodenberger, J.; Meier, J.: Einstellverfahren für ein Fahrzeugfahrwerk CONCLUSION By using a method to design complex commissioning processes, a wheel alignment process was developed that allows the steering wheel angle to be measured fully automatically with a vehicle sensor at the wheel alignment station. A basic part of the developed process has already been successfully introduced into the production process. The results so far indicate that the complete concept can be successfully implemented in the production process. With successful implementation, the gap to a fully automated wheel alignment stand can be closed and consequently the efficiency of the End-of- Line of final assembly can be increased. 62

AUTOMATED TRUCK PLATOONS ON MOTORWAYS A CONTRIBUTION TO THE SAFETY ON ROADS

AUTOMATED TRUCK PLATOONS ON MOTORWAYS A CONTRIBUTION TO THE SAFETY ON ROADS AUTOMATED TRUCK PLATOONS ON MOTORWAYS A CONTRIBUTION TO THE SAFETY ON ROADS Dipl.-Wi.-Ing. Ralph Kunze Max Haberstroh M.A. Dipl.-Ing. Dipl.-Kfm Eckart Hauck Dr.-Ing. Richard Ramakers Prof. Dr.-Ing. em.

More information

EMS ELONGATION MEASUREMENT SYSTEM. Strain measurement system for wind turbines optimizing the control & condition monitoring

EMS ELONGATION MEASUREMENT SYSTEM. Strain measurement system for wind turbines optimizing the control & condition monitoring EMS ELONGATION MEASUREMENT SYSTEM Strain measurement system for wind turbines optimizing the control & condition monitoring 2 1 1 3 3 EMS ELONGATION MEASUREMENT SYSTEM 1 Rotor blade Rotor blades are the

More information

INFLUENCE OF CROSS FORCES AND BENDING MOMENTS ON REFERENCE TORQUE SENSORS FOR TORQUE WRENCH CALIBRATION

INFLUENCE OF CROSS FORCES AND BENDING MOMENTS ON REFERENCE TORQUE SENSORS FOR TORQUE WRENCH CALIBRATION XIX IMEKO World Congress Fundamental and Applied Metrology September 6 11, 2009, Lisbon, Portugal INFLUENCE OF CROSS FORCES AND BENDING MOMENTS ON REFERENCE TORQUE SENSORS FOR TORQUE WRENCH CALIBRATION

More information

LEVER OPTIMIZATION FOR TORQUE STANDARD MACHINES

LEVER OPTIMIZATION FOR TORQUE STANDARD MACHINES LEVER OPTIMIZATION FOR TORQUE STANDARD MACHINES D. Röske, K. Adolf and D. Peschel Torque laboratory Division for Mechanics and Acoustics Phys.-Techn. Bundesanstalt, D-38116 Braunschweig, Germany Abstract:

More information

Design of Suspension and Steering system for an All-Terrain Vehicle and their Interdependence

Design of Suspension and Steering system for an All-Terrain Vehicle and their Interdependence Design of Suspension and Steering system for an All-Terrain Vehicle and their Interdependence Saurabh Wanganekar 1, Chinmay Sapkale 2, Priyanka Chothe 3, Reshma Rohakale 4,Samadhan Bhosale 5 1 Student,Department

More information

Charging Electric Vehicles in the Hanover Region: Toolbased Scenario Analyses. Bachelorarbeit

Charging Electric Vehicles in the Hanover Region: Toolbased Scenario Analyses. Bachelorarbeit Charging Electric Vehicles in the Hanover Region: Toolbased Scenario Analyses Bachelorarbeit zur Erlangung des akademischen Grades Bachelor of Science (B. Sc.) im Studiengang Wirtschaftsingenieur der Fakultät

More information

LAPPING OR GRINDING? WHICH TECHNOLOGY IS THE RIGHT CHOICE IN THE AGE OF INDUSTRY 4.0?

LAPPING OR GRINDING? WHICH TECHNOLOGY IS THE RIGHT CHOICE IN THE AGE OF INDUSTRY 4.0? LAPPING OR GRINDING? WHICH TECHNOLOGY IS THE RIGHT CHOICE IN THE AGE OF INDUSTRY 4.0? Bevel gear transmissions for the automotive industry are subject to extremely stringent requirements. They must be

More information

The AutomotiveINNOVATIONS Award 2013: Volkswagen continues to be the most innovative OEM Mercedes-Benz wins in the brand ranking

The AutomotiveINNOVATIONS Award 2013: Volkswagen continues to be the most innovative OEM Mercedes-Benz wins in the brand ranking Press release The AutomotiveINNOVATIONS Award 2013: Volkswagen continues to be the most innovative OEM Mercedes-Benz wins in the brand ranking AutomotiveINNOVATIONS Award 2013 from CAM and PwC: Volkswagen

More information

Multi-ECU HiL-Systems for Virtual Characteristic Rating of Vehicle Dynamics Control Systems

Multi-ECU HiL-Systems for Virtual Characteristic Rating of Vehicle Dynamics Control Systems Multi-ECU HiL-Systems for Virtual Characteristic Rating of Vehicle Dynamics Control Systems Dipl.-Ing. Ronnie Dessort, M.Sc. Philipp Simon - TESIS DYNAware GmbH Dipl.-Ing. Jörg Pfau - Audi AG VDI-Conference

More information

GMD 13 New gravimetric measuring system with evaluation on location

GMD 13 New gravimetric measuring system with evaluation on location Dr. Födisch Umweltmesstechnik AG Zwenkauer Strasse 159 04420 Markranstädt Germany Phone: +49 34205 755-0 Fax: +49 34205 755-40 E-mail: sales@foedisch.de Internet: www.foedisch.de GMD 13 New gravimetric

More information

Special edition paper

Special edition paper Efforts for Greater Ride Comfort Koji Asano* Yasushi Kajitani* Aiming to improve of ride comfort, we have worked to overcome issues increasing Shinkansen speed including control of vertical and lateral

More information

Hybrid Architectures for Automated Transmission Systems

Hybrid Architectures for Automated Transmission Systems 1 / 5 Hybrid Architectures for Automated Transmission Systems - add-on and integrated solutions - Dierk REITZ, Uwe WAGNER, Reinhard BERGER LuK GmbH & Co. ohg Bussmatten 2, 77815 Bühl, Germany (E-Mail:

More information

Modification of IPG Driver for Road Robustness Applications

Modification of IPG Driver for Road Robustness Applications Modification of IPG Driver for Road Robustness Applications Alexander Shawyer (BEng, MSc) Alex Bean (BEng, CEng. IMechE) SCS Analysis & Virtual Tools, Braking Development Jaguar Land Rover Introduction

More information

Simulation of Collective Load Data for Integrated Design and Testing of Vehicle Transmissions. Andreas Schmidt, Audi AG, May 22, 2014

Simulation of Collective Load Data for Integrated Design and Testing of Vehicle Transmissions. Andreas Schmidt, Audi AG, May 22, 2014 Simulation of Collective Load Data for Integrated Design and Testing of Vehicle Transmissions Andreas Schmidt, Audi AG, May 22, 2014 Content Introduction Usage of collective load data in the development

More information

Determination and improvement of bevel gear efficiency by means of loaded TCA

Determination and improvement of bevel gear efficiency by means of loaded TCA Determination and improvement of bevel gear efficiency by means of loaded TCA Dr. J. Thomas, Dr. C. Wirth, ZG GmbH, Germany Abstract Bevel and hypoid gears are widely used in automotive and industrial

More information

DLG Test Report Vredestein. Traxion Optimall. Efficiency advantages. Effizienzvorteile VF-Technologie. VF technology?

DLG Test Report Vredestein. Traxion Optimall. Efficiency advantages. Effizienzvorteile VF-Technologie. VF technology? DLG-Test DLG Test Report 6800 Vredestein Optimall Efficiency advantages Effizienzvorteile durch VF-Technologie by VF technology? www.dlg-test.de Overview A test mark DLG-APPROVED for individual criteria

More information

Tech Tip: Trackside Tire Data

Tech Tip: Trackside Tire Data Using Tire Data On Track Tires are complex and vitally important parts of a race car. The way that they behave depends on a number of parameters, and also on the interaction between these parameters. To

More information

HEIDENHAIN Measuring Technology for the Elevators of the Future TECHNOLOGY REPORT. Traveling Vertically and Horizontally Without a Cable

HEIDENHAIN Measuring Technology for the Elevators of the Future TECHNOLOGY REPORT. Traveling Vertically and Horizontally Without a Cable HEIDENHAIN Measuring Technology for the Elevators of the Future Traveling Vertically and Horizontally Without a Cable HEIDENHAIN Measuring Technology for the Elevators of the Future Traveling Vertically

More information

Thema der Arbeit. Discussion of IT-infrastructure for electric mobility. Bachelorarbeit. vorgelegt von. Patrick-Oliver Groß

Thema der Arbeit. Discussion of IT-infrastructure for electric mobility. Bachelorarbeit. vorgelegt von. Patrick-Oliver Groß Thema der Arbeit Discussion of IT-infrastructure for electric mobility Bachelorarbeit zur Erlangung des akademischen Grades Bachelor of Science (B.Sc.) im Studiengang Wirtschaftswissenschaft der Wirtschaftswissenschaftlichen

More information

Press release. Field Test on Wireless Charging of Electric Vehicles by Daimler and Conductix-Wampfler

Press release. Field Test on Wireless Charging of Electric Vehicles by Daimler and Conductix-Wampfler Field Test on Wireless Charging of Electric Vehicles by Daimler and Conductix-Wampfler The idea sounds as easy as convincing: Instead of filling up an electric vehicle by cable the driver parks conveniently

More information

The analysis of the accuracy of the wheel alignment inspection method on the side-slip plate stand

The analysis of the accuracy of the wheel alignment inspection method on the side-slip plate stand IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS The analysis of the accuracy of the wheel alignment inspection method on the side-slip plate stand To cite this article: A Gajek

More information

Pilot phase - Learnings

Pilot phase - Learnings Pilot phase - Learnings First indication of learnings from pilot phase which is ongoing LOT 4 ADVISORY BOARD MEETING BRUSSELS ACEA CO2WG TF1 WGCO2 Monday, HDV, 23 November TF1 2015 To be finalized or rather

More information

SUMMARY OF STANDARD K&C TESTS AND REPORTED RESULTS

SUMMARY OF STANDARD K&C TESTS AND REPORTED RESULTS Description of K&C Tests SUMMARY OF STANDARD K&C TESTS AND REPORTED RESULTS The Morse Measurements K&C test facility is the first of its kind to be independently operated and made publicly available in

More information

Performance of Batteries in Grid Connected Energy Storage Systems. June 2018

Performance of Batteries in Grid Connected Energy Storage Systems. June 2018 Performance of Batteries in Grid Connected Energy Storage Systems June 2018 PERFORMANCE OF BATTERIES IN GRID CONNECTED ENERGY STORAGE SYSTEMS Authors Laurie Florence, Principal Engineer, UL LLC Northbrook,

More information

HERCULES-2 Project. Deliverable: D8.8

HERCULES-2 Project. Deliverable: D8.8 HERCULES-2 Project Fuel Flexible, Near Zero Emissions, Adaptive Performance Marine Engine Deliverable: D8.8 Study an alternative urea decomposition and mixer / SCR configuration and / or study in extended

More information

PERFORMANCE OF THE NEW PRIMARY TORQUE STANDARD MACHINE OF INMETRO, BRAZIL

PERFORMANCE OF THE NEW PRIMARY TORQUE STANDARD MACHINE OF INMETRO, BRAZIL PERFORMANCE OF THE NEW PRIMARY TORQUE STANDARD MACHINE OF INMETRO, BRAZIL R. Oliveira 1, L. Cabral 1, U. Kolwinski 2, D. Schwind 2 1 INMETRO National Institute of Metrology, Xerem, Brazil 2 GTM Gassmann

More information

Furnace-based optimisation of a lignite-fired steam generator

Furnace-based optimisation of a lignite-fired steam generator Vo lu me 9 Is sue / Pa ge to Furnace-based optimisation of a lignite-fired steam generator by Daniel Sommer, Piotr Olkowski, Dieter Rüsenberg and Heinz-Jürgen Wüllenweber VGB PowerTech l Optimisation

More information

CHECK AND CALIBRATION PROCEDURES FOR FATIGUE TEST BENCHES OF WHEEL

CHECK AND CALIBRATION PROCEDURES FOR FATIGUE TEST BENCHES OF WHEEL STANDARDS October 2017 CHECK AND CALIBRATION PROCEDURES FOR FATIGUE TEST BENCHES OF WHEEL E S 3.29 Page 1/13 PROCÉDURES DE CONTRÔLE ET CALIBRAGE DE FATIGUE BANCS D'ESSAIS DE ROUE PRÜFUNG UND KALIBRIERUNG

More information

Racing Tires in Formula SAE Suspension Development

Racing Tires in Formula SAE Suspension Development The University of Western Ontario Department of Mechanical and Materials Engineering MME419 Mechanical Engineering Project MME499 Mechanical Engineering Design (Industrial) Racing Tires in Formula SAE

More information

Development of Relief Valve Automatic assembly technology

Development of Relief Valve Automatic assembly technology Development of Relief Valve Automatic assembly technology Technology Explanation Development of Relief Valve Automatic assembly technology TAKIGUCHI Masaki Abstract Construction machinery is equipped with

More information

Non-contact Deflection Measurement at High Speed

Non-contact Deflection Measurement at High Speed Non-contact Deflection Measurement at High Speed S.Rasmussen Delft University of Technology Department of Civil Engineering Stevinweg 1 NL-2628 CN Delft The Netherlands J.A.Krarup Greenwood Engineering

More information

Test report of the measurement of the leakage air flow

Test report of the measurement of the leakage air flow TÜV SAARLAND Test report of the measurement of the leakage air flow Customer: Aerotechnik Siegwart GmbH Untere Hofwiesen 66299 Friedrichsthal Test object: Air duct system with double lip sealing Test report

More information

MORSE: MOdel-based Real-time Systems Engineering. Reducing physical testing in the calibration of diagnostic and driveabilty features

MORSE: MOdel-based Real-time Systems Engineering. Reducing physical testing in the calibration of diagnostic and driveabilty features MORSE: MOdel-based Real-time Systems Engineering Reducing physical testing in the calibration of diagnostic and driveabilty features Mike Dempsey Claytex Future Powertrain Conference 2017 MORSE project

More information

The Aachen Approach on E-Mobility

The Aachen Approach on E-Mobility The Aachen Approach on E-Mobility Jan Ole Hansen Sao Paulo, October 2017 Production Engineering at RWTH Aachen University Founded in 1870 One of only 11 Elite Universities Highest third-party funds in

More information

Using Adams as master model for ECU system simulation

Using Adams as master model for ECU system simulation Using Adams as master model for ECU system simulation Dipl.-Ing. Simon Schmeiler Technische Universität München Fakultät für Maschinenwesen Lehrstuhl für Fahrzeugtechnik (FTM) Dipl.-Ing. Karl-Eric Köstlin

More information

Analysis and control of vehicle steering wheel angular vibrations

Analysis and control of vehicle steering wheel angular vibrations Analysis and control of vehicle steering wheel angular vibrations T. LANDREAU - V. GILLET Auto Chassis International Chassis Engineering Department Summary : The steering wheel vibration is analyzed through

More information

Evaluating Stakeholder Engagement

Evaluating Stakeholder Engagement Evaluating Stakeholder Engagement Peace River October 17, 2014 Stakeholder Engagement: The Panel recognizes that although significant stakeholder engagement initiatives have occurred, these efforts were

More information

Permanent Multipath Clamp-On Transit Time Flow Meter

Permanent Multipath Clamp-On Transit Time Flow Meter Permanent Multipath Clamp-On Transit Time Flow Meter By: Dr. J. Skripalle HydroVision GmbH, Germany Introduction For many years now, ultrasonic flow measurements with wetted sensors have been a well established

More information

Overload tests of Eilersen web tension sensor type SLCA 500 N

Overload tests of Eilersen web tension sensor type SLCA 500 N October, 2010 Overload tests of Eilersen web tension sensor type SLCA 500 N To check and demonstrate the overload tolerance of the Eilersen SLCA web tension sensors, a number of very severe overload tests

More information

Self-Adjusting Clutch (SAC) Technology Special tools / User instructions

Self-Adjusting Clutch (SAC) Technology Special tools / User instructions Self-Adjusting Clutch (SAC) Technology Special tools / User instructions The content of this brochure shall not be legally binding and is for information purposes only. To the extent legally permissible,

More information

Pattern evaluation programs for traffic speed measurement devices in PR China

Pattern evaluation programs for traffic speed measurement devices in PR China Pattern evaluation programs for traffic speed measurement devices in PR China Q. SUN, NIM China OIML TC7/SC4/p3 Workshop 16 to 18 July 2013, Gaithersburg Content Legal basis for traffic speed measuring

More information

KISSsys Application 008: Gearbox Concept Analysis

KISSsys Application 008: Gearbox Concept Analysis KISSsoft AG Frauwis 1 CH - 8634 Hombrechtikon Telefon: +41 55 264 20 30 Calculation Software for Machine Design Fax: +41 55 264 20 33 www.kisssoft.ch info@kisssoft.ch 1. Abstract KISSsys: Efficient Drivetrain

More information

Electromechanical Steering with Parallel-axis Drive

Electromechanical Steering with Parallel-axis Drive Service Training Self-study Programme 399 Electromechanical Steering with Parallel-axis Drive Design and Function The electromechanical power steering has many advantages compared with a hydraulic steering

More information

Proven to be better. Development trends in industrial rolling bearings

Proven to be better. Development trends in industrial rolling bearings Proven to be better Development trends in industrial rolling bearings Contents 1. General trends in power transmission and in machine construction and plant engineering Page 3 2. General trends in rolling

More information

MERCEDES-BENZ WHEEL ALIGNMENT

MERCEDES-BENZ WHEEL ALIGNMENT MERCEDES-BENZ WHEEL ALIGNMENT CAMERA TECHNOLOGY FOR YOUR WORKSHOP Powered by Photo credit: Daimler AG INVEST IN MODERN TECHNOLOGY TO GROW YOUR BUSINESS Homologated by Mercedes Benz for trucks, buses and

More information

Development of Motor-Assisted Hybrid Traction System

Development of Motor-Assisted Hybrid Traction System Development of -Assisted Hybrid Traction System 1 H. IHARA, H. KAKINUMA, I. SATO, T. INABA, K. ANADA, 2 M. MORIMOTO, Tetsuya ODA, S. KOBAYASHI, T. ONO, R. KARASAWA Hokkaido Railway Company, Sapporo, Japan

More information

Test Based Optimization and Evaluation of Energy Efficient Driving Behavior for Electric Vehicles

Test Based Optimization and Evaluation of Energy Efficient Driving Behavior for Electric Vehicles Test Based Optimization and Evaluation of Energy Efficient Driving Behavior for Electric Vehicles Bachelorarbeit Zur Erlangung des akademischen Grades Bachelor of Science (B.Sc.) im Studiengang Wirtschaftsingenieur

More information

YRTC and YRTCMA Rotary Axis Bearings with Absolute Value Angular Measuring System. Increased productivity with very high operational reliability

YRTC and YRTCMA Rotary Axis Bearings with Absolute Value Angular Measuring System. Increased productivity with very high operational reliability YRTC and YRTCMA Rotary Axis Bearings with Absolute Value Angular Measuring System Increased productivity with very high operational reliability Increased productivity with very high operational reliability

More information

Installation and Operational Instructions for EAS - HTL housed overload clutch Sizes 01 3 Type 490._24.0

Installation and Operational Instructions for EAS - HTL housed overload clutch Sizes 01 3 Type 490._24.0 Please read these Operational Instructions carefully and follow them accordingly! Ignoring these Instructions may lead to malfunctions or to clutch failure, resulting in damage to other parts. Contents:

More information

Martin Grimm. Requirements for an Ambient Interior Lighting System for Motor Vehicles

Martin Grimm. Requirements for an Ambient Interior Lighting System for Motor Vehicles Martin Grimm Requirements for an Ambient Interior Lighting System for Motor Vehicles Herausgegeben von Prof. Dr.-Ing. H.-J. Schmidt-Clausen Technische Universität Darmstadt in der Reihe Darmstädter Lichttechnik

More information

Inclinometer for Electronic Wheel Alignment Machines

Inclinometer for Electronic Wheel Alignment Machines Inclinometer for Electronic Wheel Alignment Machines Part-Number 913 009 024 Manual GEB 001 017 HAWEKA AG Kokenhorststraße 4 30938 Burgwedel 05139/8996-0 05139/8996-222 Table of Contents 1. IMPORTANT!...

More information

Identification of tyre lateral force characteristic from handling data and functional suspension model

Identification of tyre lateral force characteristic from handling data and functional suspension model Identification of tyre lateral force characteristic from handling data and functional suspension model Marco Pesce, Isabella Camuffo Centro Ricerche Fiat Vehicle Dynamics & Fuel Economy Christian Girardin

More information

Variable Valve Drive From the Concept to Series Approval

Variable Valve Drive From the Concept to Series Approval Variable Valve Drive From the Concept to Series Approval New vehicles are subject to ever more stringent limits in consumption cycles and emissions. At the same time, requirements in terms of engine performance,

More information

THE PRESENT EUROPEAN TYRE DESASTER Egon-Christian von Glasner 28

THE PRESENT EUROPEAN TYRE DESASTER Egon-Christian von Glasner 28 AKTUÁLNÍ PROBLEMATIKA ŠPATNÉHO STAVU PNEUMATIK V EVROPĚ ABSTRACT: THE PRESENT EUROPEAN TYRE DESASTER Egon-Christian von Glasner 28 Following items will be discussed: 1. The demands of the European Union

More information

Skid against Curb simulation using Abaqus/Explicit

Skid against Curb simulation using Abaqus/Explicit Visit the SIMULIA Resource Center for more customer examples. Skid against Curb simulation using Abaqus/Explicit Dipl.-Ing. A. Lepold (FORD), Dipl.-Ing. T. Kroschwald (TECOSIM) Abstract: Skid a full vehicle

More information

Kopernikus-Project ENSURE

Kopernikus-Project ENSURE Prof. Dr.-Ing. Thomas Leibfried, Karlsruhe Institute of Technology (KIT) 1 ENSURE s main goals Mission Holistic, systemic approach für new network structures 1. Goal System design with centralised and

More information

Inspekt. Static electromechanical universal testing machines. Competency generates results

Inspekt. Static electromechanical universal testing machines. Competency generates results Inspekt Static electromechanical universal testing machines Competency generates results Inspekt The great amongst the universal testing machines. A real universal testing machine should allow more than

More information

CB50X & CB50X-DL load cells Influence factors in weighbridge application

CB50X & CB50X-DL load cells Influence factors in weighbridge application CB50X & CB50X-DL load cells Influence factors in weighbridge application Introduction Vehicle scales can be considered as a platform that is supported by weight-sensing elements which produce an output

More information

USER MANUAL FOR AREX DIGI+ SYSTEMS

USER MANUAL FOR AREX DIGI+ SYSTEMS USER MANUAL FOR AREX DIGI+ SYSTEMS Arex Test Systems bv, Vennestraat 4b, 2161 LE Lisse, Holland Property of: Arex Test Systems bv Vennestraat 4b 2161 LE Lisse Tel: +31 (0) 252 419151 Fax: +31 (0) 252 420510

More information

AND CHANGES IN URBAN MOBILITY PATTERNS

AND CHANGES IN URBAN MOBILITY PATTERNS TECHNOLOGY-ENABLED MOBILITY: Virtual TEsting of Autonomous Vehicles AND CHANGES IN URBAN MOBILITY PATTERNS Technology-Enabled Mobility In the era of the digital revolution everything is inter-connected.

More information

Experience the Hybrid Drive

Experience the Hybrid Drive Experience the Hybrid Drive MAGNA STEYR equips SUV with hybrid drive Hybrid demo vehicle with dspace prototyping system To integrate components into a hybrid vehicle drivetrain, extensive modification

More information

O B J E C T I V E NON-kind-Projects

O B J E C T I V E NON-kind-Projects OBJECTIVE The Large Engines Competence Center (LEC) is an industrial competence center within the framework of the Austrian competence center program of the Federal Ministry of Economics and Labour. The

More information

How do things run smoothly even in rough winds?

How do things run smoothly even in rough winds? How do things run smoothly even in rough winds? Rotor blade inspection during production and ongoing operation Rotor blade quality essential for energy yield Rotor blades must satisfy the most stringent

More information

White paper: Pneumatics or electrics important criteria when choosing technology

White paper: Pneumatics or electrics important criteria when choosing technology White paper: Pneumatics or electrics important criteria when choosing technology The requirements for modern production plants are becoming increasingly complex. It is therefore essential that the drive

More information

Test Report No

Test Report No Empa Überlandstrasse 129 CH-8600 Dübendorf Tel. +41 (0)44 823 55 11 Fax +41 (0)1 821 62 44 www.empa.ch Materials Science & Technology Lista AG Betriebs- und Lagereinrichtungen CH-8586 Erlen Test Report

More information

Balancing of aeroderivative turbine

Balancing of aeroderivative turbine Balancing of aeroderivative turbine Guillaume Christin 1, Nicolas Péton 2 1 GE Measurement and Control, 68 chemin des Ormeaux, 69760 Limonest, France 2 GE Measurement and Control, 14 rue de la Haltinière,

More information

Insights into WLTP and RDE

Insights into WLTP and RDE Insights into and RDE Current test procedures and their implications for fleet customers Editorial Dear Readers, You have already been informed about the first phase of the new Worldwide Harmonised Light

More information

Filter and Particle Simulation for Hydraulic Systems

Filter and Particle Simulation for Hydraulic Systems 1 Filter and Particle Simulation for Hydraulic Systems Karl Wartlick Argo-Hytos GmbH, Kraichtal-Menzingen, Germany René von Dombrowski RWTH Aachen University, Germany, Institute for Fluid Power Drives

More information

Structural Analysis Of Reciprocating Compressor Manifold

Structural Analysis Of Reciprocating Compressor Manifold Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2016 Structural Analysis Of Reciprocating Compressor Manifold Marcos Giovani Dropa Bortoli

More information

Transmitted by the expert from the European Commission (EC) Informal Document No. GRRF (62nd GRRF, September 2007, agenda item 3(i))

Transmitted by the expert from the European Commission (EC) Informal Document No. GRRF (62nd GRRF, September 2007, agenda item 3(i)) Transmitted by the expert from the European Commission (EC) Informal Document No. GRRF-62-31 (62nd GRRF, 25-28 September 2007, agenda item 3(i)) Introduction of Brake Assist Systems to Regulation No. 13-H

More information

Tire Uniformity Machine, LIBROTA

Tire Uniformity Machine, LIBROTA Tire Uniformity Machine, LIBROTA Shinichiro IKAI *1, Yasuhiro MATSUSHITA *2 *1 Machinery Business Industrial Machinery Division Industrial Machinery Department *2 Machinery Business Industrial Machinery

More information

Challenges in a controlled system to stop the air velocity in case of fire in a road tunnel

Challenges in a controlled system to stop the air velocity in case of fire in a road tunnel Challenges in a controlled system to stop the air velocity in case of fire in a road tunnel Robert Pucher Department Computer Science University of Applied Sciences Technikum Wien Höchstädtplatz 5,1200

More information

GT-Suite Users Conference

GT-Suite Users Conference GT-Suite Users Conference Thomas Steidten VKA RWTH Aachen Dr. Philip Adomeit, Bernd Kircher, Stefan Wedowski FEV Motorentechnik GmbH Frankfurt a. M., October 2005 1 Content 2 Introduction Criterion for

More information

Evaluation of Vibrostrengthening for Fatigue Enhancement of Titanium Structural Components on Commercial Aircraft

Evaluation of Vibrostrengthening for Fatigue Enhancement of Titanium Structural Components on Commercial Aircraft Evaluation of Vibrostrengthening for Fatigue Enhancement of Titanium Structural Components on Commercial Aircraft D. H. Gane 1, Y. S. Rumyantsev 2, H. T. Diep 1, L. Bakow 1 1 Boeing Commercial Aircraft

More information

Development and validation of a vibration model for a complete vehicle

Development and validation of a vibration model for a complete vehicle Development and validation of a vibration for a complete vehicle J.W.L.H. Maas DCT 27.131 External Traineeship (MW Group) Supervisors: M.Sc. O. Handrick (MW Group) Dipl.-Ing. H. Schneeweiss (MW Group)

More information

E. Rodt 2 UBA Berlin Berlin Germany. EU / GRPE: "Particulate measurement program" (PMP)

E. Rodt 2 UBA Berlin Berlin Germany. EU / GRPE: Particulate measurement program (PMP) E. Rodt 2 UBA Berlin Berlin Germany EU / GRPE: "Particulate measurement program" (PMP) Particulate Measurement Programme (PMP) of ECE-GRPE Stefan Rodt, UBA Berlin Abstract This presentation describes an

More information

LEAKAGE CLASS ACHIEVED? Wöhler DP 700 LEAKAGE TEST ON VENTILATION SYSTEMS AND COMPONENTS. The Measure of Technology GRAPHIC COLOR DISPLAY GRAPHIC

LEAKAGE CLASS ACHIEVED? Wöhler DP 700 LEAKAGE TEST ON VENTILATION SYSTEMS AND COMPONENTS. The Measure of Technology GRAPHIC COLOR DISPLAY GRAPHIC LEAKAGE CLASS ACHIEVED? GRAPHIC COLOR DISPLAY COLOR DISPLAY GRAPHIC LEAKAGE TEST ON VENTILATION SYSTEMS AND COMPONENTS The Measure of Technology Made in Germany Leakage Tester Just 3 entries to classify

More information

THE INFLUENCE OF PHYSICAL CONDITIONS OF SUSPENSION RUBBER SILENT BLOCKS, IN VEHICLE HANDLING AND ROAD- HOLDING

THE INFLUENCE OF PHYSICAL CONDITIONS OF SUSPENSION RUBBER SILENT BLOCKS, IN VEHICLE HANDLING AND ROAD- HOLDING REGIONAL WORKSHOP TRANSPORT RESEARCH AND BUSINESS COOPERATION IN SEE 6-7 December 2010, Sofia THE INFLUENCE OF PHYSICAL CONDITIONS OF SUSPENSION RUBBER SILENT BLOCKS, IN VEHICLE HANDLING AND ROAD- HOLDING

More information

PERFECTLY POSITIONED FOR ANY CHASSIS.

PERFECTLY POSITIONED FOR ANY CHASSIS. SUSPENSION SPRINGS PERFECTLY POSITIONED FOR ANY CHASSIS. Egon von RUVILLE GmBH Billbrookdeich 112 22113 Hamburg Germany Tel.: +49 40 73344-0 Fax: +49 40 73344-199 info@ruville.de www.ruville.de NEW IN

More information

China International Automotive Congress Vehicle concepts, tailor made for e-propulsion. Shenyang, 13. September 2009

China International Automotive Congress Vehicle concepts, tailor made for e-propulsion. Shenyang, 13. September 2009 China International Automotive Congress 2009 Vehicle concepts, tailor made for e-propulsion Shenyang, 13. September 2009 Prof. Dr.-Ing. habil. J.-W. Biermann Dipl.-Ing. Bastian Hartmann Institut für Kraftfahrzeuge

More information

IAEA Workshop 2010 Machine Development at TMB

IAEA Workshop 2010 Machine Development at TMB IAEA Workshop 2010 Machine Development at TMB Prof. Dr.-Ing. Sascha Gentes KIT University of the State of Baden-Wuerttemberg and National Research Center of the Helmholtz Association www.kit.edu Agenda

More information

ELECTRIFICATION OF RTG CRANES

ELECTRIFICATION OF RTG CRANES ELECTRIFICATION OF RTG CRANES MAKING PORTS MORE SUSTAINABLE WITH ertg SOLUTIONS Up to 95 % savings in diesel fuel costs Up to 95 % savings in diesel fuel costs the ECOLOGICAL solution the ECOLOGICAL solution

More information

SYSTEM COMPARISON OF

SYSTEM COMPARISON OF SYSTEM COMPARISON OF steel & ALUMINIUM PISTONS FOR PC DIESEL ENGINES In recent years, the steel piston has proven to be significantly superior to its aluminium counterpart under the special operating conditions

More information

Icing Wind Tunnel tests in the framework of a Wing Ice Protection system certification process

Icing Wind Tunnel tests in the framework of a Wing Ice Protection system certification process Icing Wind Tunnel tests in the framework of a Wing Ice Protection system certification process AirTN-NextGen Workshop on Virtual testing, towards virtual certification Amsterdam (NL), May 25, 2016 Use

More information

Correction of test cycle tolerances: assessing the impact on CO 2 results. J. Pavlovic, A. Marotta, B. Ciuffo

Correction of test cycle tolerances: assessing the impact on CO 2 results. J. Pavlovic, A. Marotta, B. Ciuffo Correction of test cycle tolerances: assessing the impact on CO 2 results J. Pavlovic, A. Marotta, B. Ciuffo WLTP 2 nd Act November 10, 2016 Agenda Flexibilities of test cycle and laboratory procedures

More information

CONTRIBUTION TO THE CINEMATIC AND DYNAMIC STUDIES OF HYDRAULIC RADIAL PISTON MOTORS.

CONTRIBUTION TO THE CINEMATIC AND DYNAMIC STUDIES OF HYDRAULIC RADIAL PISTON MOTORS. Ing. MIRCEA-TRAIAN CHIMA CONTRIBUTION TO THE CINEMATIC AND DYNAMIC STUDIES OF HYDRAULIC RADIAL PISTON MOTORS. PhD Thesis Abstract Advisor, Prof. dr. ing. matem. Nicolae URSU-FISCHER D.H.C. Cluj-Napoca

More information

New Development of Highly Efficient Front-Wheel Drive Transmissions in the Compact Vehicle Segment

New Development of Highly Efficient Front-Wheel Drive Transmissions in the Compact Vehicle Segment New Development of Highly Efficient Front-Wheel Drive Transmissions in the Compact Vehicle Segment Introduction Dr. Ing. Ansgar Damm, Dipl.-Ing. Tobias Gödecke, Dr. Ing. Ralf Wörner, Dipl.-Ing. Gerhard

More information

Cost-Benefit Analysis of Options for Certification, Validation and Monitoring and Reporting of HDVs

Cost-Benefit Analysis of Options for Certification, Validation and Monitoring and Reporting of HDVs CO 2 HDV Stakeholder Meeting Cost-Benefit Analysis of Options for Certification, Validation and Monitoring and Reporting of HDVs Leif-Erik Schulte Vicente Franco Brussels, January, 30 th 2015 1 Overview

More information

The Self-Adjusting Clutch SAC of the 2 nd Generation

The Self-Adjusting Clutch SAC of the 2 nd Generation The Self-Adjusting Clutch SAC of the 2 nd Generation Dipl.-Ing. Karl-Ludwig Kimmig Introduction The self-adjusting clutch (SAC) has proven itself in almost 1 million vehicles. in particular vehicles with

More information

Midterm Event. Holger Czuday, Bayern Innovativ 7th February Automotive Battery Recycling and 2nd Life

Midterm Event. Holger Czuday, Bayern Innovativ 7th February Automotive Battery Recycling and 2nd Life Midterm Event Holger Czuday, Bayern Innovativ 7th February 2014 Automotive Battery Recycling and 2nd Life 1 Consortium: D NL - F External: Paris, 15 janvier 2014 2 Problem description Daily message at

More information

Development of an innovative diaphragm accumulator design and assembly process

Development of an innovative diaphragm accumulator design and assembly process Group 7 - Hydraulic Components Paper 7-3 451 Development of an innovative diaphragm accumulator design and assembly process Dipl.-Ing. Thorsten Hillesheim Freudenberg Sealing Technologies GmbH & Co. KG,

More information

Development of a Mobile Application for Android to Support Energy-Efficient Driving of Electric Vehicles

Development of a Mobile Application for Android to Support Energy-Efficient Driving of Electric Vehicles Development of a Mobile Application for Android to Support Energy-Efficient Driving of Electric Vehicles Masterarbeit zur Erlangung des akademischen Grades Master of Science (M.Sc.) im Studiengang Wirtschaftsingenieur

More information

Comprehensive analysis energy efficiency of large buildings / halls Summary

Comprehensive analysis energy efficiency of large buildings / halls Summary Dresden Institute for Building Systems Engineering Research and Application GmbH Prof. Oschatz - Dr. Hartmann - Dr. Werdin - Prof. Felsmann University Kassel Department Building Physics Comprehensive analysis

More information

TESTING OF AUTOMOBILE VW GOLF OPERATING ON THREE DIFFERENT FUELS

TESTING OF AUTOMOBILE VW GOLF OPERATING ON THREE DIFFERENT FUELS TESTING OF AUTOMOBILE VW GOLF OPERATING ON THREE DIFFERENT FUELS Ilmars Dukulis, Vilnis Pirs, Zanis Jesko, Aivars Birkavs, Gints Birzietis Latvia University of Agriculture Ilmars.Dukulis@llu.lv, Vilnis.Pirs@llu.lv,

More information

Six keys to achieving better precision in linear motion control applications

Six keys to achieving better precision in linear motion control applications profile Drive & Control Six keys to achieving better precision in linear motion control applications Achieving precise linear motion Consider these factors when specifying linear motion systems: Equipped

More information

Alternative Wind Turbine Drive Train with Power Split and High-speed Generators

Alternative Wind Turbine Drive Train with Power Split and High-speed Generators Alternative Wind Turbine Drive Train with Power Split and High-speed Generators Dipl.-Ing. Cristian Andrei 1 Dipl.-Ing. Simon Serowy 2 Dipl.-Ing. Björn Riemer 1 Univ.-Prof. Dr.-Ing. habil. Dr. h. c. Kay

More information

Industry Best Practices in Reliability Prediction and Assurance for Power Electronics: Part 1 - Reliability of Power Electronics Components

Industry Best Practices in Reliability Prediction and Assurance for Power Electronics: Part 1 - Reliability of Power Electronics Components Industry Best Practices in Reliability Prediction and Assurance for Power Electronics: Part 1 - Reliability of Power Electronics Components NAME AND AFFILIATION OF THE AUTHORS Eckhard Wolfgang, ECPE e.v.

More information

PROJECT IDEA SUBMISSION

PROJECT IDEA SUBMISSION PROJECT IDEA SUBMISSION Team Contacts - 1 st person listed serves as the point of contact with Professor Nelson - Initial team size may be from 1 to 6 members (all members must agree to have their name

More information

Highly dynamic control of a test bench for highspeed train pantographs

Highly dynamic control of a test bench for highspeed train pantographs PAGE 26 CUSTOMERS Highly dynamic control of a test bench for highspeed train pantographs Keeping Contact at 300 km/h Electric rail vehicles must never lose contact with the power supply, not even at the

More information

Optimizing Battery Accuracy for EVs and HEVs

Optimizing Battery Accuracy for EVs and HEVs Optimizing Battery Accuracy for EVs and HEVs Introduction Automotive battery management system (BMS) technology has advanced considerably over the last decade. Today, several multi-cell balancing (MCB)

More information