SAFETY AND HEALTH STANDARD VEHICLES AND DRIVING Effective Date:12/17/16 Standard 15.3 Document Number:KUCSH0032 Rev:09

Transcription

1 Effective Date:12/17/16 Standard 15.3 Dcument Number:KUCSH0032 Rev: INTRODUCTION: This standard establishes the minimum requirements fr safely perating vehicles and mbile equipment n r ff KUC prperty. This standard applies t all vehicles, including mbile equipment wned and / r perated by KUC r its cntractrs, that is used n r ff-site, and t the persnnel wh perate such equipment DEFINITIONS: Class 2 Strbe Light Hazard warning strbe light certified by the Sciety f Autmtive Engineers. Cite law and safety cncern Heavy Mbile Equipment (HME) Mbile equipment specially designed fr executing mining tasks Light Duty Vehicle (LDV) Any land-based vehicle with a grss vehicle weight rating less than 10,000 punds (example: van, pickup, SUV, etc.) Medium Duty Vehicle (MDV) Any land-based vehicle with a grss vehicle weight rating greater than 10,000 punds (example: service truck, bus, crane truck, etc.) REQUIREMENTS: Cmprehensive risk analyses shall be cnducted t identify the factrs that impact vehicles and driving safety. The risk analyses will: Include all aspects f vehicles and driving and will have up-tdate actin plans in place t manage identified issues. (The plans will be reviewed peridically t imprve vehicle and driving safety) Identify the cnditinal and behaviral factrs that impact vehicles and driving safety at KUC (See Risk ID: 64). Outline the prtcl fr site driving and licensing f KUC emplyees and cntractrs (See Risk ID: 1382). Review the elements f the Ri Tint Light Duty Vehicle Guideline (See Risk ID: 1383) All vehicles used fr wrk purpses require a risk assessment. The risk assessment must be repeated when / if permanent mdificatin Page 1 f 11 Kennectt Utah Cpper. The standards n the KUC Intranet website are cnsidered the standard in effect and supersede all ther revisins.

2 Effective Date:12/17/16 Standard 15.3 Dcument Number:KUCSH0032 Rev:09 t the vehicle s functin r a majr cmpnent mdificatin ccurs. Risk assessments may be perfrmed n a per-fleet basis fr likevehicles. Risk assessment dcumentatin will be kept n file at each facility and will be updated as required. A VEHICLES & DRIVING RISK ASSESSMENT FORM is attached as Exhibit The assessment must: Invlve a representative frm the peratin and maintenance grups wh will use the vehicle; and Address all aspects f safe peratin including munting and dismunting, handling, driver visin, brake failure, tire blw-uts, seat belts, fire extinguishers / suppressin systems and access / egress fr peratrs, maintainers and passengers, rll-ver prtectin and ergnmics The peratr must cmplete a pre-peratin inspectin checklist befre the equipment is placed int peratin n each shift. The inspectin checklist will be based n the risk assessment fr that fleet r unit. When defects make cntinued peratin hazardus, the equipment shall be taken ut f service and placed in a designated area psted fr that purpse, r an alternative effective methd f marking / tagging the unit shall be used t prhibit further use until the defects are crrected. Equipment will nt be perated if the preshift inspectin identifies a serius r ptentially serius safety prblem. Defects n vehicles r mbile equipment, affecting safety that are nt crrected immediately shall be reprted t the apprpriate supervisr and recrded. Inspectin cards will remain n file fr six mnths All vehicles and mbile equipment must be fitted with fixed seats and safety belts fr the driver and all passengers. The driver and all passengers must wear their seat belt at all times All light vehicles used fr wrk purpses must cmply with all aspects f the Ri Tint Light Vehicle Guidelines unless the risk assessment specifies therwise (See Risk ID #1383) In general, all vehicles and mbile equipment used fr wrk purpses that are capable f exceeding the lwest psted speed limit must be fitted with a functinal speedmeter. Exceptins t this requirement are made fr thse types f equipment where perating speeds are strictly cntrlled and enfrced by site perating prcedures / plicies and site licensing requirements All persns required t drive / perate vehicles at KUC must cmply Page 2 f 11 Kennectt Utah Cpper. The standards n the KUC Intranet website are cnsidered the standard in effect and supersede all ther revisins.

3 Effective Date:12/17/16 Standard 15.3 Dcument Number:KUCSH0032 Rev:09 with the requirements utlined in the KUC Risk Assessment - Prtcl fr Site Driving and Licensing f Emplyees and Cntractrs (Risk ID #1382) and at a minimum, have : A valid State r Civil driving license and depending n the vehicle, a valid Department f Transprtatin Cmmercial Drivers License, and A site specific license when required t drive at the Mine r Tailings Impundment. Certain exceptins t these licensing requirements may be granted in rare circumstances at the sle discretin f KUC All accident / incidents that result in an ccupatinal injury r illness and / r damage t physical assets and near miss incidents shall be prmptly reprted and investigated. (See Safety & Health Standard 6.1) In the event f an ff-site accident in a cmpany wned vehicle refer t Exhibit Off-site Vehicle Accidents Vehicles and mbile equipment shuld be kept free f excess dirt, grease and il. Cabs and beds will be kept clear f lse items such as pp cans, lunch pails, unsecured fire extinguishers, rags, etc.,. Windws are t be cleaned as ften as necessary. Peridic cleaning will be cmpleted as needed Prir t entering shp facilities fr repair wrk, mbile equipment is t be cleaned f debris build-up Beds f trucks are nt t be used as refuse cntainers. Only necessary equipment may be carried and is t be neatly stred. Tl lckers and bxes are t be rganized and free f debris. Hwever, direct hauling f debris t prper dispsal cntainer / landfill is acceptable where the lad is prperly secured and cvered Fundamentally Stable Parking: Mbile equipment shall nt be left unattended unless prperly secured unable t mve under its wn energy, r the influence f gravity. All peratrs will park their vehicles in a psitin that will nt endanger persnnel r equipment. Then t satisfy the requirements f fundamental stability the peratr will: 1. Place the transmissin in park r lw gear. 2. Apply the park break 3. Turn ff the engine, and 4. If the vehicle is nt psitined against a suitable berm, in a parking ditch, r ther designed immbilizing device, place a wheel chck n a tire in the directin the vehicle will rll. Page 3 f 11 Kennectt Utah Cpper. The standards n the KUC Intranet website are cnsidered the standard in effect and supersede all ther revisins.

4 Effective Date:12/17/16 Standard 15.3 Dcument Number:KUCSH0032 Rev:09 Fundamentally stable parking requirements fr ff-rad prductin, cnstructin, and ther specialized mbile equipment will be determined via risk assessment fr each equipment class and applied universally acrss all plant sites N vehicle may tw, r be twed, unless it is engineered t d s. Determinatin will be made in the risk assessment whether a vehicle can tw r be twed. Rigging r lifting equipment will nt be used fr twing applicatins Speed limits and signage will be set in accrdance with generally accepted rad safety standards. Where there are established speed limits and traffic rules, they must be reviewed regularly and enfrced. Traffic rules, signals, and warning signs shall be standardized at each site The use f any cellular device while perating any vehicle n cmpany prperty r while n cmpany business is prhibited. DRIVING IN THE MINE N persn may perate a vehicle inside the mine area unless he / she has a pit license r is cntinuusly escrted. Because f the cnstantly changing mine cnditins, n persn shall be licensed t drive in the mine unless they are required t d s mre than nce in a tw-week perid. Site licensed emplyees and cntractrs wh are away frm the wrkplace fr lnger than 14 cnsecutive calendar days r 10 wrking days must receive a rerientatin prir t returning t wrk and perating vehicles in the Mine. Renewal f site licenses will be based an assessment f cmpetency t drive and / r perate equipment. The frequency f assessment will be either annual, r derived frm a risk assessment fr each vehicle type. All light and medium duty vehicles perating n haul rads must have: Headlights n at all times. An amber strbe light n at all times. Strbe lights must meet r exceed Class 2 certificatin. A white lighted whip flagple with a whip flag that extends at least 12 ff the grund and is visible frm all directins. Clear identificatin n sides, rear, and rf f the vehicle with letters / numbers at least A4 in size (8.3 x 11.7 in). Page 4 f 11 Kennectt Utah Cpper. The standards n the KUC Intranet website are cnsidered the standard in effect and supersede all ther revisins.

5 Effective Date:12/17/16 Standard 15.3 Dcument Number:KUCSH0032 Rev:09 Vehicles r equipment (ther than thse being laded as part f the peratins) that enter a shvel pit r apprach a manned shvel, dzer, frnt-end lader r blasthle drill must make psitive (tw way) cntact with the peratr f that equipment prir t entering the wrking area f the equipment. All ft traffic entering a shvel pit r appraching a manned shvel, dzer, frnt-end lader r blasthle drill must make psitive (tw way) cntact with the peratr f that equipment prir t entering the wrking area f the equipment. - Psitive (tw-way) cntact must be made at least 50 meters (160 feet) away frm the equipment r befre passing under a cable bridge, whichever is greater. Psitive cntact des nt have t be made when: - A haul truck is entering an area t be laded. - A haul truck is passing near a dzer in the dump area. - An area is physically demarcated by a berm r ther barrier s as t allw passing. - A vehicle is passing (rather than appraching ) a shvel dzer, frnt-end lader r blasthle drill in transit t anther destinatin, prvided that pass is nt made within the immediate wrking radius f the equipment being passed. Overtaking (passing) in the pit area is allwed subject t the exercise f safe and prudent driving practice. N vehicle will vertake a haul truck r water truck n the blind side withut first making psitive cntact with the driver. Vehicles may nt pass at any time within a rad intersectin, at the crest f a hill, r under any circumstance where visin is restricted. DRIVING ON THE TAILINGS IMPOUNDMENT N persn may perate a vehicle n the tailings impundment unless he / she has a tailings impundment license r is cntinuusly escrted. Renewal f site licenses will be based an assessment f cmpetency t drive and / r perate equipment. The frequency f assessment will be derived frm a risk assessment fr each vehicle type, but will nt exceed fur years. (See MSHA Petitin fr Mdificatin Dcket N. M M) Each access pint frm the uter radway area t the impundment radway shall have psted warnings that the Page 5 f 11 Kennectt Utah Cpper. The standards n the KUC Intranet website are cnsidered the standard in effect and supersede all ther revisins.

6 Effective Date:12/17/16 Standard 15.3 Dcument Number:KUCSH0032 Rev:09 impundment radway is nt bermed and that cautin must be used. The impundment radway shall nt be used as a thrughfare and traffic shall be limited t a ne-way directin. The impundment radway speed shall nt be mre than 15 miles per hur, depending n weather, rad, and visibility cnditins. Speed limit signs shall be psted at apprpriate entrance lcatins t the impundment radway. Reflective delineatrs shall be installed at n mre than 500-ft intervals alng the impundment radway and shall be visible, under nrmal weather cnditins, frm equipment using the radway TIRE AND RIM SAFETY Tire and rim safety requirements applies t tires and rims f size 24 inch and greater. It is supprted by the tire and rim safety wrk cycle Operatins must establish a Tire management plan that is apprved by the senir manager at the peratin and reviewed every 12 mnths There must be demnstrated jb cmpetencies and safe wrk prcedures fr all tire maintenance, servicing activities and tire fire emergency respnse. The cmpetencies must specify the frequency fr re-certificatin, which must be n less than every three years N persn may apprach a vehicle within 24 hurs f; lightning strike, cntact with high vltage electricity, tire fire. An exclusin zne f 1000 feet f a tire fire must be established and nly be accessed by emergency service persnnel that are shielded while fighting the fire Restricted wrk znes (RWZ) and exclusins znes must be established fr the tire installatin, remval and handling prcesses All tire and rim handling equipment must have fall back preventin in place prir t anyne entering the RWZ Tires with split rims must be deflated t zer and ther tires t a nminal pressure n greater than 5psi prir t remval f any retaining devices. In a dual assembly bth tires must be deflated Tire inflatin is subject t the fllwing requirements: Remte inflatin must be used fr all tire inflatin Page 6 f 11 Kennectt Utah Cpper. The standards n the KUC Intranet website are cnsidered the standard in effect and supersede all ther revisins.

7 Effective Date:12/17/16 Standard 15.3 Dcument Number:KUCSH0032 Rev:09 Where the risk f ejectin f cmpnents exists barricading must be in place A tire must nt be left unattended during inflatin Tires that have run at less than 80 percent cld inflatin pressure must nt be re-inflated. Bth tires in a dual assembly must be dismunted and inspected N welding, cutting r applicatin f heat surces t a rim r wheel must be dne while the rim r wheel is fitted with a tire - whether inflated r deflated A peridic testing and/r inspectin regime must be in place fr tires, rims/wheels and assemblies All tires, rims/wheels must be made unserviceable when deemed unfit fr service r befre being sent ff site fr dispsal A tracking system must be in place t track the lifecycle f tires, rims/wheels RESPONSIBILITIES Operatrs are respnsible fr cnducting and dcumenting the apprpriate pre-peratinal inspectin prir t perating the vehicle. Operatrs are respnsible fr the rutine cleanliness f cabs, platfrms and windws f vehicles It is the respnsibility f the driver t ensure that all passengers wear their seat belts, at all times when the vehicle is in peratin Each KUC facility shall have a system in place t ensure that the renewal f site licenses will be based n an assessment f cmpetency t drive and r perate the equipment. The frequency f assessment will be either annual, r derived frm a risk assessment fr each vehicle type TRAINING N persn may drive a vehicle unless he / she is trained, cmpetent, tested and licensed t perate that vehicle. The training must address hazards assessed fr that vehicle r fleet, and the task(s) fr which it is t be used N persn may perate a vehicle inside the mine area unless he/she has cmpleted the pit driver training r is cntinuusly escrted. Page 7 f 11 Kennectt Utah Cpper. The standards n the KUC Intranet website are cnsidered the standard in effect and supersede all ther revisins.

8 Effective Date:12/17/16 Standard 15.3 Dcument Number:KUCSH0032 Rev: Any persn driving r perating equipment n the Tailings Impundment shall receive and cmplete the Tailings Impundment training requirements defined in the KUCC MSHA Petitin fr Mdificatin, r be accmpanied by a persn that has received the specified training. REFERENCES: - MSHA 30 CFR Part 56; Subpart M a. - MSHA Petitin fr Mdificatin Dcket N. M M (Tailings Impundment) - Ri Tint Safety Standard C3 Vehicles and Driving - KUC Risk Analysis ID# 64, 1382 and Ri Tint Light Vehicle Guidelines - Ri Tint Variance C3. Vehicles and Driving 5.3(c) Psitive Cntact and Passing - KUC Safety and Health Standard 6.1 Accident / Incident Investigatin & Case Management REVISION HISTORY: MOC# Descriptin f Change Prepared By Date TS00125 Additin f Off site Vehicle Accident prcedure KUC Safety and Health Standards Cmmittee 07 / Changes submitted by the V&D cmmittee t update standard t cmply with the Ri Tint new tire safety requirements with the additin f paragraph TIRE AND RIM SAFETY. Als, updated referenced Risk Assessment ID numbers, and Dcument number Updated Fundamentally Stable Parking requirement and Mine vehicle definitins KUC Safety and Health Standards Cmmittee KUC Safety and Health Standards Cmmittee 11/ /2016 Page 8 f 11 Kennectt Utah Cpper. The standards n the KUC Intranet website are cnsidered the standard in effect and supersede all ther revisins.

9 KENNECOTT UTAH COPPER Exhibit KENNECOTT UTAH COPPER VEHICLES & DRIVING RISK ASSESSMENT FORM TYPE: Level 1 Pre-Task Hazard Assessment# DESCRIPTION: Make: Mdel: Year: Lad Rating: INDIVIDUAL UNIT FLEET UNIT NUMBER UNIT NUMBERS APPROVED EQUIPMENT FUNCTION: REASON FOR ASSESSMENT: Initial Assessment New Equipment Existing Equipment Peridic Review Mdified Equipment (Explain) Check all equipment that is currently fitted. Equipment that is nt fitted must be installed r included in the Risk Assessment with an Actin Plan. If nt necessary indicate in Risk Assessment and why. Date Installed Fitted Date Installed Anti-slip surfaces Backup alarm Backup lights Brake lights Buggy whip (flag) Buggy whip (light) Driver s seat (fixed) Driver s seat belt Emergency flashers Engine temp. gauges / alarms Exhaust system Fire extinguisher Fire suppressin system First aid kit Fuel gauge / alarm Handrails / platfrms Headlights Hrn Lights (fld / spt) Limit Switches Lckut / tagut mechanism Fitted *Number f passengers allwed n equipment: Mirrr driver side Mirrr passenger side Oil pressure gauge / alarm Over speed alarm Parking brake Passenger seat belt(s)* Passenger seat(s)* (fixed) Retarder ROPS FOPS Service brakes Speedmeter Pwer Steering Taillights Twing equipment Turn signals Tw-way radi Wheel / track chcks Windshield wipers / washer Other: Other: NOTE: A KUC Level 1 n-line Risk Assessment is required t be cmpleted fr all vehicles types used fr wrk purpses. Page 9 f 11 Kennectt Utah Cpper. The standards n the KUC Intranet website are cnsidered the standard in effect and supersede all ther revisins.

10 KENNECOTT UTAH COPPER Exhibit Off-site Vehicle Accidents Cmpany Owned Vehicle Respnsibility fr ensuring that the fllwing actins are carried ut rests with the driver, if he/she is capable f ding s. In thse cases where the driver is unable t attend t these matters, the respnsibility rests with any ther KUC / Ri Tint emplyee present at the accident. Cntact plice. D nt admit any liability (even if the driver believes it was his/her fault). D nt make any statements t ther parties r witnesses ther than the plice. Exchange infrmatin at the scene: - Names, - Cntact infrmatin, - Insurance, - Driver s license details, - Vehicle descriptin and license plate number. Obtain names and addresses f witnesses. Recrd details f any ther vehicle/s invlved. Take pictures, if pssible camera phnes are handy at the scene. Recrd details f lcatin, time and nature f the accident. After an Accident The driver r any ther KUCC emplyee invlved in an accident in a cmpany vehicle must infrm their manager and the Ri Tint Risk Management Office as sn as pssible after the accident and cmplete a Ri Tint incident reprt frm (See Exhibit ). All vehicle accidents must be investigated in accrdance with Standard 6.1 Accident / Incident Investigatin. If there is damage t the KUC vehicle, and the vehicle is safe t perate, return it t the facilities and cntact Kennectt Operatinal Services (KOS) wh will arrange fr repairs. If the vehicle is nt safe t perate, if pssible, call KOS t arrange fr twing. If the Plice arrange the twing, get the apprpriate infrmatin and cntact KOS fr fllw-up. All persnnel shuld be aware f the trauma that can be experienced by peple invlved in accidents r when rendering assistance. This trauma may surface sme time after the accident. It may be apprpriate t cnsider actins such as: cunseling, escrting the persn hme r t medical attentin, r reprting the situatin t yur manager. Ri Tint s aut cverage is liability based it prvides cverage fr damage t ther s prperty and persnal injury. Physical damage t vehicles is nt cvered under the plicy. Due t limits within the plicy, KUCC is cnsidered self-insured and is respnsible fr the expense. Page 10 f 11 Kennectt Utah Cpper. The standards n the KUC Intranet website are cnsidered the standard in effect and supersede all ther revisins.

11 KENNECOTT UTAH COPPER Exhibit Ri Tint Aut Incident Reprt All aut incidents/accidents must be reprted. Prvide a cmplete reprt t yur supervisr and t Risk Management. Risk Management cntact: Marla D Antnimarla.dantni@ritint.cm Phne: INCIDENT SITE: Where? (city & zip cde) Weather cnditins: Speed befre incident: When? (date & time): Rad cnditins: Lights On r Off Field Cde Ch PARTIES INVOLVED: Ri Tint driver #1: Supervisr s name: Business unit & cst center Supervisr s phne: ( ) Vehicle:(yr/make/mdel) License plate #: Damage incurred: Vehicle Owner: Vehicle current lcatin? Driver #2 name: Driver s Lic. #: State: Hme address: Phne number: ( ) City /St/ Zip: Ins. Plicy # Insurance cmpany: Ins cmpany phne: ( ) Vehicle:(yr/make/mdel) License plate #: Damage incurred: Vehicle Owner: Witness #1 name: Phne number: ( ) Invlved hw? Witness #2 name: Phne number: ( ) Invlved hw? Plice fficer s name: Officer s department: Officer s ID number: Citatin issued? Against whm? What charge? INJURIES: Name Address Phne Injured #1 ( ) Injuries / Hspital: Injured #2 ( ) Injuries / Hspital: Injured #3 ( ) Injuries / Hspital: DESCRIBE HOW ACCIDENT OCCURRED: SKETCH A DIAGRAM: Include a hand drawing including street names, directin f vehicles, and psitin at cntact. ATTACHMENTS: Pictures Plice reprts Repair estimate(s) Driver s signature: Supervisr s signature: Date: Date: Page 11 f 11 Kennectt Utah Cpper. The standards n the KUC Intranet website are cnsidered the standard in effect and supersede all ther revisins.