STS INSTALLATION MANUAL MECHANICAL SWITCH
|
|
- Dennis Williams
- 6 years ago
- Views:
Transcription
1 Thank you for making the road a safer place! STS INSTALLATION MANUAL MECHANICAL SWITCH STS INSTALLATION MANUAL USER MANUAL DISCLAIMER AND WARRANTY COMPANY INFORMATION
2 Please carefuly follow steps descirbed in installation manual! Wrong connection of STS wires to motorcycle may cause damage of STS device! Every STS device is equipt with chip which indicates false connection. If chip shows wrong connection, warranty is void. This installation manual is for motorcycles with flasher and mechanical (latching) switch (Most motorcycles except for Ducati, BMW and few other motorcycles with electrical switch for those please choose electronic version manual) Before installation please check if you have mechanic turn signal switch (latching): 1. Turn off your motorcycle; 2. Press left or right turn signal switch; 3. Turn on your motorcycle > if turn signal is blinking you have a mechanical version! We strongly advise STS system installation is made only by authorized person! Please read installation manual before installation process! Pictures in installation manuals are illustrative! Power supply must be taken from ACC wire (ignition 12 V), not permanent 12 V from battery. 2
3 Tools needed: Phillips, Torx and Imbus Screwdriver Pliers Cutting Pliers Tweezers Crimping pliers 1. In order to install STS you have to connect STS unit to following wires: Left turn signal wire Right turn signal wire Flasher Ground Power supply 2. Locate wires listed above and follow them from left handlebar switch to connector 3
4 3. Find a spot for STS device (black box) STS unit has 50 cm (20 inch) of cable so it has to be located near listed wires Spot for STS device has to be flat and fairly horizontal STS device has to be attached to housing, not on the handle bar (not even on rudder or any other moving part) It is advised to connect STS device with zip tie, so try to find a spot that allows this and attach it firmly It is recommended that the module be mounted in a location not subject to extreme heat conditions Sticker with the STS Logo must look up Arrow in the STS Logo must point in the driving direction (forward) If necessary add velcro or double side tape (not included in the package) 4. When you have located wires and find a spot for STS device remove approximately 10 cm (4 inch) of primary cable isolation 4
5 5. Locate: Left turn signal, Right turn signal, Flasher (Reset), ACC (Power supply) and GND (Ground) wire STS Please note that chart is universal based on gathered data from manufacturer and wires on your motorcycle might be different Please check colors in wiring diagram for your exact motorcycle. This can be found in service manual, online or ask your local mechanic STS device has 8 wires and you have to connect each of them to corresponding wire on your motorcycle Motorcycle Power supply (+12V) Red Color 1 Ground (GND) Black Color 2 OUTPUT (wire to connector): Right output Yellow Color 3 Left output Blue Color 4 Flasher output Green Color 5 INPUT (wire from handlebar): Right input White Color 3 Left input Brown Color 4 Flasher input Purple Color 5 6. Powe supply wires: 6.1. Snap Violet Tap connector to ACC (Power supply) wire (we recommend position lamp, DRL or any other 12 V power source from ignition 12 V, not permanent 12 V from battery) 5
6 6.2. Snap Violet Tap connector to GND wire 7. Turn signals wires: 7.1. Cut left turn signal, right turn signal and flasher relay wire 6
7 7.2. Strip cutted wires 7.3. Wires are now stripped 7.4. On motorcycle connector side of wires insert FEMALE crimp bullet connectors 7
8 7.5. Crimp inserted female connectors 7.6. On handlebar switch side of wires insert MALE crimp bullet connectors 7.7. Crimp inserted male connectors 8
9 8. IMPORTANT! Before inserting STS wires to connectors: INPUT are part of wires coming from handlebar switch OUTPUT are part of wires going to connector 9. WIRING SCHEME BEFORE STS INSTALLATION 10. WIRING SCHEME OF STS INSTALLATION Wrong connection of STS wires to motorcycle may cause damage of STS device! Warranty is void! 9
10 10.1. Insert STS wires with Faston connectors to violet Tap connectors in following way: BLACK STS wire to GND (Ground) RED STS wire to Power supply (+12V) Insert STS wires with red bullet connectors in following way: BLUE STS wire to Flasher signal OUTPUT (IMPORTANT! do not mix up INPUT and OUTPUT) YELLOW STS wire to Right indicator OUTPUT GREEN STS wire to Left indicator OUTPUT Do not connect other three wires Turn ignition on (or start your motorcycle), watch carefully on turn signals. After aprox 1 sec you will see turn signals blink for short time. Continue to next step (step 10.4.) If that does not happen, please repeat 2 or 3 times. If you are sure turn signals did not blink, please check power supply, if that still does not work please check your wiring or see troubleshooting (step 15.) Insert remaning STS wires with red bullet connectors in following way: WHITE STS wire to Right indicator INPUT BROWN STS wire to Flasher signal INPUT PURPLE STS wire to Left indicator INPUT 10
11 11. Attach STS unit (black box) to motorcycle housing Spot for STS device has to be flat and fairly horizontal STS device has to be attached to housing, not on the handle bar (not even on rudder or any other moving part) It is advised to connect STS device with zip tie, so try to find a spot that allows this and attach it firmly It is recommended that the module be mounted in a location not subject to extreme heat conditions Sticker with the STS Logo must look up Arrow in the STS Logo must point in the driving direction (forward) If necessary add velcro or double side tape (not included in the package) 12. Modify turn signal switch to momentary Objective of modifying the turn signal switch is to convert mechanical (latching) switch into a momentary switch Loosen the screws that clamp on to the handlebar Four foams are supplied with the package - two big and two small sized foams. Smaller foams are perfect fit for most motorcycle switches, based on our experience. Bigger foams Smaller foams There are two basic types of left handlebar switches (LHS): Type 1: Type 2: Honda, Yamaha, Suzuki, Kawasaki, Triumph, (Switch may vary in visual appearance from the outside.) Scooters, Mopeds 11
12 Type 1 LHS There are two basic variations of Type 1 LHS: Open 1 LHS or Covered 1 LHS. Open 1 LHS: Open switch: Same switch from different angle: Insert smaller foams into cavities with tweezers. As you move the leaver from side to side, plastic slider moves from one side to another. Left side: Right side: 12
13 Covered 1 LHS: Switch may vary in visual appearance from inside Loosen the screw(s) (highlighted with red circle), remove the covering and you will find two cavities where foams have to be inserted. Insert smaller foams into cavities with tweezers. As you move the leaver from side to side, the plastic slider moves from one side to another. Left side: Right side: After inserting the foam plugs, make sure the switch has full motion, but does not stay in the position. Reassemble the LHS back to the handlebar. 13
14 Type 2 LHS These kinds of switches are mostly used on smaller bikes (scooters, mopeds). Disassemble the switch from handlebar. Remove top plastic cover by removing it with a screwdriver. Your switch should look like this: Take the bigger foam included in the package and slice it into two pieces like shown in the picture below: Whole big foam --> bigger piece + smaller piece Insert the smaller piece of foam into the smaller cavity and the bigger piece into the bigger cavity: After inserting the foam plugs, make sure the switch has full motion but does not stay in the position. Reassemble the cover and LHS back to the handlebar. 14
15 13. Test STS unit First try Device has to be completely steady Turn ignition on (or start your motorcycle), watch carefully on turn signals After aprox 1 sec you will see turn signals blink for short time (1 blink) If that does not happen, please turn egnition on 2 or 3 times more/again If you are sure turn signals did not blink, please check power supply, if that still does not work please check your wiring or see troubleshooting If your turn signals blinked, connect also purple, white and brown wire and proceed to next step (step 13.3) Testing procedure Start your motorcycle and wait for few seconds Press left indicator and wait for 30 second Press left indicator again to cancel turn signal Repeat procedure for right turn signal If procedure works as described, poceed to nex step (step 14.) 14. Reassemble all components back to it s original place Universal wire scheme chart please check in service manual or ask your local mechanic STS Color Connector Honda Yamaha Kawasaki Suzuki Vespa Triumph Power supply (+12V) Ground (GND) Red Black Faston male Faston male OUTPUT (wire to connector- inside of motorcycle): Right output Flasher output Left output Yellow Blue Green Male Bullet Light Blue Dark Green Gray Light Green Male Bullet Gray Brown/White Orange Light Blue White / Blue (Bi-Bl) Blue / Black (Bl-Ne) Gray (S) Orange (O) Male Bullet Orange Chocolate Green Black Pink (Ro) Green (G) INPUT (wire from handlebar): Right input White Flasher input Brown Left input Purple Female Bullet Light Blue Dark Green Gray Light Green Female Bullet Gray Brown/White Orange Light Blue White / Blue (Bi-Bl) Blue / Black (Bl-Ne) Gray (S) Orange (O) Female Bullet Orange Chocolate Green Black Pink (Ro) Green (G) IMPORTANT! Colours listed in chart above are informative and may not be same on your motorcycle. Please check in service manual or ask your local mechanic. 15
16 15. Troubleshooting: Wait 30s with ignition on. Take away ignition and put ignition again on. Check Power supply wire (+ 12 V DC and GND) for propper connection Check if STS Device (black box with logo) is steady. If you don't see blink in previous steps, connect midle (flasher relay) male faston bullet on the motorcycle wires to right or left male faston bullet on motorcycle wires. o If you see blinks now, you have put wrong connectors to wrong side of cutted cables. Contact us for sending another set of connectors or go to local electronics / moto shop for replacement connectors. Contact us, if you have any questions on: support@safer-turn.com 16. User manual When you push left or right turn signal leaver, turn signals will start blinking If you want to cancel turn signal, push to same side again After each manoeuvre STS cancels turn signals in compliance with road rules STS recognizes and differentiate: o Left or right turn o Changing lane o Roundabout o Overtaking STS recognizes when you are standing still and will not turn off turn signals If STS doesn't turn off after maneuver, timer will turn off turn signals after 15 seconds of driving Operating voltage: 12 V (DC) Power consumption: 250 mw 17. Disclaimer To the maximum extent permitted by applicable law neither ABCS sistem d.o.o. nor its suppliers, its subcontractors, its affiliates, officers, directors, employees, dealers or agents shall be liable to you or to any third party for any incidental damage including personal injury or any other damages, whether direct, special, incidental, indirect or consequential arising out of or related to: Smart Turn System not working correctly due to improper calibration of the system and/or any other usage that is not in comply to Smart Turn System user manual. Damage made on motorcycle due to improper installation and/or improper use of Smart Turn System. Turn signals not blinking due to improper installation or calibration. Smart Turn System not canceling turn signals after the end of maneuver or turn signals canceling prematurely (during drive/before maneuver is completed). Smart Turn System is a device that assist motorcyclist to cancel turn signals after the end of maneuver. Smart Turn System can detect maneuver and cancels turn signal after the maneuver 16
17 is completed. Due to various driving styles and motorcycle types company ABCS sistem d.o.o. can take no responsibility if Smart Turn System doesn t detect maneuver and consequently doesn t cancel turn signal after any maneuver. Furthermore ABCS sistem d.o.o. can take no responsibility if turn signals are canceled prematurely. Correct turn signal usage is motorcyclist responsibility and STS device is meant only to assist rider with turn signal cancellation. 18. Improper installation or operation of Smart Turn System Smart Turn System device has to be installed according to ABCS sistem installation manual. If you are not sure about any part of installation manual or/and your motorcycle wiring scheme please contact ABCS sistem d.o.o. at support@safer-turn.com. 19. Warranty Limited Warranty applies to physical goods, and only for physical goods, purchased from ABCS Sistem d.o.o. (the "Physical Goods"). Limited Warranty covers any defects in material or workmanship under normal use during the Warranty Period. During the Warranty Period, ABCS Sistem d.o.o. will repair or replace, at no charge, products or parts of a product that proves defective because of improper material or workmanship, under normal use and maintenance. ABCS Sistem d.o.o. will either repair the Product at no charge, using new or refurbished replacement parts. The Warranty Period for Physical Goods purchased from ABCS Sistem d.o.o. is 365 days from the date that the product was shipped. A replacement Physical Good or part assumes the remaining warranty of the original Physical Good or 180 days from the date of replacement or repair, whichever is longer. This Limited Warranty does not cover any problem that is caused by: conditions; malfunctions or damage not resulting from defects in material or workmanship. To obtain warranty service, you must first contact our support@safer-turn.com to determine the problem and the most appropriate solution for you. ABCS Sistem d.o.o. Vojkova cesta Ljubljana Slovenia - EU support@safer-turn.com 17
Caution! Some procedures must be followed in order to avoid damages from occuring to the vehicle.
Thank you for purchasing KOSO's TNT-04 meter. Please read the instructions carefully and retain them for future reference. Notice To avoid a short circuit from occuring do not pull or modify the wires
More informationISIS Power Manual and Installation Guide Race Car Replicas- Superlite Coupe
ISIS Power Manual and Installation Guide Race Car Replicas- Superlite Coupe Table of Contents Overview... 2 System Details... 3 Kit Includes... 3 Technical Specifications... 3 Harness Descriptions... 4
More informationInstallation and Operation Instructions BMW 3 E93 Convertible Comfort Module
Installation and Operation Instructions BMW 3 E93 Convertible Comfort Module Before installation: Please read these instructions carefully and take your time with the installation. Performing the installation
More informationInstallation and Operation Guide
Bus-Scan 500 RF Installation and Operation Guide All Content and Information are Copyright 2018-2019 Robotics Technologies, Inc. Features and Information are subject to change without notice. All Rights
More informationInstallation and Operation Instructions Peugeot 207cc Comfort Module
Installation and Operation Instructions Peugeot 207cc Comfort Module Before installation: Please read these instructions carefully and take your time with the installation. Performing the installation
More informationRemove the 3-11mm nuts holding mirror on. Don t drop the nuts!
2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit
More informationATTENTION. Custom Dynamics Smart Triple Play Installation Instructions. Package Contents: - Smart Triple Play Module (1) - Instructions
Custom Dynamics Smart Triple Play Installation Instructions We thank you for purchasing the Custom Dynamics Smart Triple Play. Our products utilize the latest technology and high quality components to
More informationINSTALLATION CLAMP-ON FORK MOUNTED DRIVING LIGHTS 5015
CLAMP-ON 5015 PARTS INCLUDED 2 Driving Lights 2 Side Mount Clamps-43mm/49mm 1 Hardware Kit Including: 2 49mm Spacers 4 43mm Spacers 2 Pivot Dome Washers 2 3/8-16 Serrated Hex Nut 1 Wiring Kit for Driving
More informationREMOTE CENTRAL LOCK. Model: CLRxxx-ULT
REMOTE CENTRAL LOCK Model: CLRxxx-ULT Contents Remote Lock, Remote Unlock, Car Finder, Remote Boot release:, Power Window outoput, Learning Transmitter Codes... page 3 Wiring Diagram... page 4 Introduction,
More informationCAPACITOR ACTUATED PORTABLE STARTER CAPS USER GUIDE. INST048 Doc 3.01
CAPACITOR ACTUATED PORTABLE STARTER CAPS USER GUIDE INST048 Doc 3.01 CONTENTS General Information...2 Charts...3 Before First Use...4 Safety Requirements...5 What to Expect from the CAPS...5 CAPS Diagram...6
More informationQuick-Kill Installation Manual V1.0 (Universal Motorcycle Application)
Quick-Kill Installation Manual V1.0 (Universal Motorcycle Application) THIS INSTALLATION MANUAL IS FOR UNIVERSAL FUEL INJECTED MOTORCYCLE APPLICATIONS (NON PLUG AND PLAY), WITH OR WITHOUT A GEAR POSITION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS www.factorydirectperf.com Made exclusively for FDP by SEA-DOO 800 Enhancer Ignition, PN 30-08-2630 Fits SEA-DOO XP, GSX, GTX Watercraft w/rave Engine IMPORTANT: Read these instructions
More informationInstallation and Operation Guide
Bus-Scan CR2 RF Installation and Operation Guide All Content and Information are Copyright 2018 Robotics Technologies, Inc. Features and Information are subject to change without notice. All Rights Reserved.
More informationINSTALLATION. DRIVING LIGHTS for FLHT/FLHX/FLHR 5005
DRIVING LIGHTS for FLHT/FLHX/FLHR 5005 PARTS INCLUDED 1 Right Driving Light Assembly 1 Left Driving Light Assembly 1 Right Driving Light Bracket 1 Left Driving Light Bracket 4 Driving Light Bracket Plugs
More information* * APPLICABLE MODELS: 2014 > Mazda 3
PART NUMBER: 0000 8C L48 (DIO) / 0000 89 L84 (PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0700-000* APPLICABLE MODELS: 2014 > Mazda 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage
More information* * APPLICABLE MODELS: 2014 > Mazda 6
PART NUMBER: 0000 8C H02(DIO) / 0000 89 H18(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0694-000* APPLICABLE MODELS: 2014 > Mazda 6 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage
More informationBluetooth Smart Speed/Cadence Sensor Instruction Manual
Bluetooth Smart Speed/Cadence Sensor Instruction Manual Contents Before using this product... 3 Warranty... 4 List of Parts... 4 Battery... 6 Installation... 7 Pairing... 11 Technical Specs... 11 2 WARNINGS:
More informationSOLAR DASH CHARGING SYSTEM USER GUIDE
SOLAR DASH CHARGING SYSTEM Doc 1.01 INST049 INSTALLATION STEP 1 Place 20 watt solar panel in the dash of the vehicle facing up. Note: For ideal results position the vehicle in a manner in which the solar
More informationAccessory Fuse Block. Please read this entire manual before proceeding with installation.
Accessory Fuse Block Please read this entire manual before proceeding with installation. Kit Components: (1) Fuse Block Assembly (1) Harness (1) Positive power cable (1) Negative power cable (5) Pigtails
More informationadvanced FLOW engineering Instruction Manual P/N: SCORCHER BLUE Bluetooth Power Module
advanced FLOW engineering Instruction Manual P/N: 77-84009 SCORCHER BLUE Bluetooth Power Module Make: Chevrolet Model: Colorado Year: 2016-2019 Engine: I4-2.8L (td) Duramax (LWN) Make: GMC Model: Canyon
More informationFor questions or technical support, 1. Wiring Reference:
Warning: Before proceeding you are obligated to read and agree to the terms and conditions attached to this manual. Misuse of this product may cause injury or death. Incorrect installation may cause damage
More informationComponents. Options Accessory Harness USB Charger. Quick Connector. Hook & Loop / Cable-ties. RFID Antenna. Module. Main Harness.
SRX SERIES Table of Contents - Components - Planning The Install - Mounting - Switched Power - Attach Accessory Harness - Plug In Module - Back-Up Battery - Remote Encoding - 2-Way RFID Remote User Instructions
More informationInstalling the Audiovox CCS-100 Cruise Control.
Installing the Audiovox CCS-100 Cruise Control. This article was written by: Lon Lawrence w650kawasaki@leaco.net Cruise Control : Audiovox CCS-100 ($89) Webpage : www.summitracing.com Message: I've installed
More informationTRAILER AUXILIARY POWER SYSTEM (TAPS) INSTALLATION GUIDE V1.10
TRAILER AUXILIARY POWER SYSTEM (TAPS) INSTALLATION GUIDE V1.10 TAPS INSTALLATION GUIDE V1.10 1 TRAILER AUXILIARY POWER SYSTEM CONTENTS General Information and System Logic... 2 Diagrams... 3 System Diagram
More informationInstallation Guide. Index. Vehicle Canbus Integration System
Platform: CANMAX00 Rev.: 20003 Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product.
More informationINSTALLATION CONSTELLATION DRIVING LIGHTS 5009
INSTALLATION CONSTELLATION DRIVING LIGHTS 5009 PARTS INCLUDED 1 Right Driving Light with Turn Signals 1 Left Driving Light with Turn Signals 1 Installation Component Kit Including: 8 Insulated Male Spades
More informationRemove 4 circled pins. Route wiring along dashed line. Remove the 2 9mm nuts and black retaining plate that secure extractor.
2015 Ford Mustang Turn Signal Hood Kit Parts List: Quantity: Tool List: Bracket & pre-installed lamp 2 Flat head screwdriver Wiring harness 1 Phillips screwdriver PB-3660 Parts Bag 1 Ratchet & Socket set
More informationINSTALLATION INSTRUCTIONS
Backup Camera Interface (Kit # 9002-7762) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Cam T-Harness Plug & Play I/O T-Harness
More informationTo ensure correct operation and service please read these instructions before installing and operating the TPMS P451 TPMS Manual TABLE OF CONTENTS
To ensure correct operation and service please read these instructions before installing and operating the TPMS P451 TPMS Manual TABLE OF CONTENTS TIRE PRESSURE MONITORING SYSTEMS, TPMS... 2 NOTICE...
More information* * APPLICABLE MODELS: 2017 > CX-5
PART NUMBER: 0000 8C R06(DIO) / 0000 89 R28(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0681-000* APPLICABLE MODELS: 2017 > CX-5 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart
More informationHeadlight Removal & Installation: BMW E36
Headlight Removal & Installation: BMW E36 Disclaimer: Buyer assumes any and all risk and liability from the installation and use of this product. Seller, author, or any of their affiliates assume no liability
More informationNEXTUP TERMINAL STRIP CONTROLLER INSTALLATION MANUAL - VER 1.5
CONTENTS INTRODUCTION 1 STEP ONE QUICKSHIFTER Power and Ground 3 STEP TWO QUICKSHIFTER Wiring and Final Connections 4 STEP ONE AIR SHIFTER Power and Ground 6 STEP TWO AIR SHIFTER Wiring and Final Connections
More informationINSTALLATION OVERVIEW:
INSTALLATION OVERVIEW: signalminder is a 100% solid-state device, which replaces the existing turn signal relay of your bike - in many cases this a simple plug-in procedure. But depending on your bike,
More informationMain Harness Quantity: 1
Smart Engine Start INSTALLATION MANUAL Genuine Part # : H001SVA900 Vehicle Model : WRX Kit Contents Service P/N: H001SVA910 Service P/N: H001SVA820 NOT USED NOT USED SES ECU Quantity: 1 Double-sided tape
More informationDYNOTUNE 2 STAGE RPM WINDOW SWITCH WITH TPS INSTALLATION INSTRUCTIONS
DYNOTUNE 2 STAGE RPM WINDOW SWITCH WITH TPS INSTALLATION INSTRUCTIONS Introduction: READ ALL INSTRUCTIONS BEFORE STARTING! This DynoTune device will control up to two stages of nitrous oxide. They are
More information2JZGTE Installation Manual Firmware Version 3.0
2JZGTE Installation Manual Firmware Version 3.0 Warnings: Before proceeding you are obligated to read and agree to the terms and conditions attached to this manual. Misuse of this product may cause injury
More informationVehicle Service Parts (may be required for reassembly) Legend
Toyota Part Number: 00016-32901 Accessory Code: KE1 Corolla 2014 Note: Not for installation on vehicles equipped with factory keyless entry Additional Items Required For Installation Item# Quantity Req.
More informationApplicable to the Following Part Numbers. Notes and Maintenance. Torque Specifications. Metric SAE. Use above torque setting unless otherwise noted
INSTALLATION MANUAL Level of Difficulty Moderate This is the second first of two of two manuals required to complete this installation. The first second manual manual is is included with with your mounting
More informationMSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219
INSTALLATION INSTRUCTIONS MSD SB6 Programmable Ignition for the Kawasaki ZX-14 PN 4219 Parts Included: 1 - Ignition 1 - Wiring Harness 1 - Parts Bag 1 - CD ROM WARNING: When installing the SB6, disconnect
More informationMANSI CLS Series LPG/CNG Closed Loop System with Harness and Actuator Motor
MANSI CLS Series LPG/CNG Closed Loop System with Harness and Actuator Motor ratio(afr) is efficiently controlled to minimize emissions, maximize efficiency and improve mileage. This product features extremely
More informationINSTALLATION CONSTELLATION DRIVING LIGHTS 5009
INSTALLATION CONSTELLATION DRIVING LIGHTS 5009 PARTS INCLUDED 1 Right Driving Light with Turn Signals 1 Left Driving Light with Turn Signals 1 Installation Component Kit Including: 8 Insulated Male Spades
More informationINSTALLATION, MAINTENANCE & SERVICE MANUAL
INSTALLATI, MAINTENANCE & SERVICE MANUAL M151217L Product Specifications 20" (506mm) 3.3 (85mm) 9.8 (250mm) 38" (974mm) 4.2 (106mm) 9.8 (250mm) 48" (1208mm) 4.2 (106mm) 56" (1442mm) 4.2 (106mm) Wiring
More informationInstruction Manual. G-Series Rear View Replacement Mirror Monitor with 7.3 MirrorLink Display RVS-718-7ML. Rear View Safety, Inc.
Instruction Manual G-Series Rear View Replacement Mirror Monitor with 7.3 MirrorLink Display RVS-718-7ML Rear View Safety, Inc. 2016 Reverse With Confidence 1 TABLE OF CONTENTS Introduction...............................
More informationINSTALLATION. Note: Not all parts will be used in the installation of this product. -cont.-
5005 Fits: 06-up FLHX, 04-up Screamin Eagle Ultra Classic Electra Glide & Screamin Eagle Electra Glide Classic, '97-up FLHT, FLHTC, FLHTCU, FLHR PartS Included 1 Right Driving Light Assembly 1 Left Driving
More informationPIAA Multi-Fit 005/1100X Light Bracket Kits
ENGLISH PIAA Multi-Fit 005/1100X Light Bracket Kits Thank you for your purchase. Please read all the instructions before beginning.! WARNING Lighting laws vary state to state, check your local laws before
More informationINSTALLATION INSTRUCTIONS
THANK YOU FOR CHOOSING KURYAKYN! Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding the installation,
More informationINSTALLATION LIGHTED CURVED LAY DOWN LICENSE PLATE MOUNT 3166
INSTALLATION LIGHTED CURVED LAY DOWN LICENSE PLATE MOUNT 3166 PARTS INCLUDED 1 Lighted Curved Lay Down License Plate Assembly 1 Hardware Kit Including: 6 Cable Ties 1 Dielectric Grease Pack 1 1 x 8 Tape
More informationNISSAN 370Z INTELLI-KEY Rev.:
Remote Starter NISSAN 70Z 009-00 INTELLI-KEY Rev.: 0096 009 Not included: x Fuse 5Amp x s Amp x Relays Override OEM Transponder Immobilizer Via Data (No Key Required). Interfaces directly with the latest
More informationEasy-On Wireless Tail Lights User s Guide
Easy-On Wireless Tail Lights User s Guide TAKE NOTICE: BY INSTALLING OR OTHERWISE USING THE EASY-ON WIRELESS TAIL LIGHTS YOU AGREE TO FOLLOW THE BELOW DIRECTIONS CAREFULLY AND BE BOUND BY THE LIMITATION
More informationMulti-Function Switch
1 of 9 Nissan Frontier, Xterra 1998-05 Multi-Function Switch REMOVAL & INSTALLATION Fig. Multi-function switch component locations 1998-2000-2000 shown Before servicing, or working around, the SRS system,
More informationInstallation Instructions
Installation Instructions for EVS II Security and Keyless Entry Systems Note: It is recommended that this installation take place prior to rustproofing. The individual delivering the vehicle should review
More informationPOWERED RUNNING BOARDS INSTALLATION MANUAL
POWE RUNNING BOARDS INSTALLATION MANUAL Level of Difficulty Moderate Parts List 1 Driver / left running board* 1 Passenger / right running board* 4 Mounting bracket, standard 2 Mounting bracket, middle
More informationChevy Sonic 2012-up G
INSTALLATION INSTRUCTIONS FOR PART 99-3012 APPLICATIONS Chevy Sonic 2012-up 99-3012G KIT FEATURES ISO DIN Head unit provision with pocket DDIN Head unit provisions Painted Gray to match factory finish
More informationUSB Charge Port Installation Instructions
USB Charge Port Installation Instructions Lifetime Technical Support support@logolites.com 770-476-7322 www.logolites.com Manual 100-0014C Thank you for purchasing a Logo Lites USB Charge Port! USB Charge
More informationTrimSync Installation & Operating Instructions
TrimSync Installation & Operating Instructions Mounting the Device The unit should be mounted in a dry area away from sources of heat. Mounting the unit near the trim pumps will reduce wiring complications.
More informationInstallation instructions
Installation instructions Akrapovič Exhaust System Slip-On for the BMW S 1000 RR *505775* EN Revision 1.0 04/2017 www.akrapovic.com www.akrapovic.com Congratulations on purchasing the Akrapovič exhaust
More informationadvanced FLOW engineering Instruction Manual P/N:
advanced FLOW engineering Instruction Manual P/N: 77-84010 Make: Chevrolet Model: Silverado HD Year: 2017-2018 Engine: V8-6.6L (td) Duramax (L5P) Make: GMC Model: Sierra HD Year: 2017-2018 Engine: V8-6.6L
More informationJeep Cherokee Latitude/Limited 2014-up
Installation instructions for part 99-6526 REV. 5/23/2017 INST99-6526 KIT FEATURES ISO DDIN radio provision Included interface shows climate and menu info on the aftermarket radio screen. Painted scratch-resistant
More informationGROM Interface Installation into Nissan and Infiniti cars using NIS2 vehicle specific harness
GROM Interface Installation into Nissan and Infiniti cars using NIS2 vehicle specific harness Tools needed 1. The wire crimp tool 2. Panel trim removal tool (optional) 3. Philips screwdriver Picture 1:
More informationGentex by VOXX Corporation Installation Instructions
Gentex by VOXX Corporation Installation Instructions Bezelled ADVGEN45A4 Bezelled w/ Homelink ADVGEN80EXP ADVGEN45A4PW4 ADVGEN40A4 Frameless ADVGEN8EXP Frameless w/ Homelink ADVGEN85EXP ADVGEN45AB5 TOOLS
More informationINSTALLATION. Note: Not all of the included parts will be used during this installation. -cont.-
Driving Lights for Road Glide 5007 Fits: 98-up Road Glide PartS Included 1 Right Light Assembly 1 Left Light Assembly 1 Right Mounting Bracket 1 Left Mounting Bracket 1 Hardware Kit Including: 2 Narrow
More informationFit a Japanese Regulator Rectifier unit to a 12v AC/DC Royal Enfield Bullet
Fit a Japanese Regulator Rectifier unit to a 12v AC/DC Royal Enfield Bullet The standard, seperate regulator and rectifier units on the later model Royal Enfield Bullet are not noted for their reliability.
More informationADVANCED EMERGENCY BRAKING SYSTEM (AEBS) DISCLAIMER
ADVANCED EMERGENCY BRAKING SYSTEM (AEBS) DISCLAIMER OnGuardACTIVETM Disclaimer WABCO s advanced emergency braking system (AEBS) with active braking on moving, stopping and stationary vehicles OnGuardACTIVE
More informationToyota Supra MKIII Installation Manual Firmware Version 3.1
Toyota Supra MKIII Installation Manual Firmware Version 3.1 Warnings: Before proceeding you are obligated to read and agree to the terms and conditions attached to this manual. Misuse of this product may
More informationModel 2008 I Battery Operated Irrigation Timer with 3/4 in. Anti-Siphon Valve
i n s t r u c t i o n m a n u a l Model 2008 I Battery Operated Irrigation Timer with 3/4 in. Anti-Siphon Valve Features Weekly or cyclical programming 4 start times per day in weekly program Irrigation
More informationInstallation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles)
Installation Tips for your Remote Start system (for RS4LX>GMBP for GM vehicles) Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to doit-yourself
More informationSAFETY-- SECURITY-- SIMPLICITY! TM
T3 Vehicle Security Tracker Installation Guide SAFETY-- SECURITY-- SIMPLICITY! TM 911Tracker.com T3 Vehicle Security Tracker Installation Guide COPYRIGHTS 2017 911Tracker All rights reserved. 911Tracker
More informationInstallation instructions
Installation instructions Akrapovič Exhaust System Slip-On for the Kawasaki Z800 *503616* EN Revision 1.0 02/2016 www.akrapovic.com www.akrapovic.com Congratulations on purchasing the Akrapovič exhaust
More informationAltair Electronic Ignition System for
Altair Electronic System for 3 Cylinder Motorcycles System# AL3 Altair Electronic System for Triumph Trident T150, T150V, T160 X75 Hurricane BSA A75R Rocket 3 Features Fully digital design Compact digital
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-8115 2002-2003 FORD F350 Super Duty V10-6.8L SEE * NOTE 2000-2003 FORD Excursion V10-6.8L SEE * NOTE 1999-2003
More informationINSTALLATION ZOMBIE L.E.D. FUEL & BATTERY GAUGE. THANK YOU FOR CHOOSING KϋRYAKYN!
THANK YOU FOR CHOOSING KϋRYAKYN! PROTECT YOURSELF AND OTHERS FROM POSSIBLE INJURY AND PROPERTY DAMAGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS, AND NOTICES REGARDING THE, USE,
More informationSafety Sentry Electronic Breakaway Switch
Safety Sentry Electronic Breakaway Switch P-616-WE 819-0454 Installation Instructions An Altra Industrial Motion Company Parts List Mounting hardware included with the Safety Sentry Breakaway Switch kit:
More informationInterior Digital Load Scale 202-DDG-02. Installation and Operation Manual Please read carefully before installation
Interior Digital Load Scale 202-DDG-02 Installation and Operation Manual Please read carefully before installation Contents Specifications:... 2 1.0 Installation and Set-up Overview... 3 2.0 Gauge Installation
More informationFan Backstop Clutches Models HFB & VFB
Fan Backstop Clutches Models HFB & VFB P-7675-FC-A4 BULLETIN A-3039 Installation Instructions Model HFB for Horizontal Shafts Model VFB for Vertical Shafts An Altra Industrial Motion Company Introduction
More informationModel A Turn Signal Kit Installation Guide
Model A Turn Signal Kit Installation Guide Creative Connections, Inc. Consumer Hot Line: 888-471-LOGO 770-476-7322 In Atlanta, GA http://www.logolites.com P/N: 100-005/K 2008 Creative Connections, Inc.
More informationTOYOTA SIENNA LED DRL Black-Out
TOYOTA SIENNA 2013 - LED DRL Black-Out Part Number: 00016-08021 Accessory Code: LDBO10 Conflicts - Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 2 DRL s bezels 3 1 Driver
More informationInstallation instructions
Installation instructions Akrapovič Exhaust System Racing and Evolution for the Yamaha YZ250F FOR CLOSED COURSE COMPETITION USE ONLY. NOT INTENDED FOR STREET USE. *505579* EN Revision 1.0 10/2016 www.akrapovic.com
More informationInstallation Instructions for the Lingenfelter Fan and Pump Manual Override Kit
Installation Instructions for the Lingenfelter Fan and Pump Manual Override Kit PN: L300180000 v1.1 Lingenfelter Performance Engineering 1557 Winchester Road Decatur, IN 46733 (260) 724-2552 (260) 724-8761
More informationInstallation instructions
Installation instructions Akrapovič Exhaust System Slip-On for the Kawasaki Versys 1000 *503272* EN Revision 1.0 02/2016 www.akrapovic.com www.akrapovic.com Congratulations on purchasing the Akrapovič
More informationDoor lock and key interface compatible with the latest Kia vehicles. The available features include brake, hood, trunk and door trigger sensors.
Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide Door
More informationInstallation instructions
Installation instructions Akrapovič Exhaust System Slip-On for the Yamaha YZ450F FOR CLOSED COURSE COMPETITION USE ONLY. NOT INTENDED FOR STREET USE. *503910* EN Revision 1.0 02/2016 www.akrapovic.com
More informationCYCLE COMPUTER OWNER'S MANUAL ENGLISH FRANÇAIS ESPANOL DEUTSCH ITALIANO
CYCLE COMPUTER OWNER'S MANUAL ENGLISH FRANÇAIS ESPANOL DEUTSCH ITALIANO INTRODUCTION Congratulations on your purchase of the new Vetta C-06 cycle computer. The C-06 is designed to be the simplest, smallest
More informationADVANCED KEYLESS ENTRY SYSTEM INSTALL GUIDE.
REV.2009.04.10 KE-6 ADVANCED KEYLESS ENTRY SYSTEM TM INSTALL GUIDE www.ultrastarters.com FCC ID NOTICE This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
More informationCDL - 04R / CDL - 04 USER S / INSTALLERʼS MANUAL
CDL - 04R / CDL - 04 USER S / INSTALLERʼS MANUAL Manufacturer: COMMERCIAL ELECTRONICS 264 HAYDONS ROAD, WIMBLEDON, LONDON SW19 8TT. UK TEL: +44 020 8404 7105 FAX: +44 020 8404 7104 http://www.hawkcaralarm.com
More informationInstallation Instructions. Manual # For Installing: Part # Painless Gauge Controller
Installation Instructions Manual #90579 For Installing: Part #60650- Painless Gauge Controller Perfect Performance Products, LLC Painless Performance Products Division 2501 Ludelle Street Fort Worth, TX
More informationI. SIM card preparation 3 II. Installation into a vehicle 3. III. Most common issues and their solutions 9 III. Attachments 10
Contents I. SIM card preparation 3 II. Installation into a vehicle 3 1. Placement of the unit 3 2. Connecting the wiring harness 4 2.1 Input - IGNITION 6 2.2 Input ALARM INPUT 6 2.3 Output (switching relay)
More informationElectric Bike User Manual
Electric Bike User Manual HAVE A QUESTION? NEED HELP? Contact us on Facebook for a quick reply. westhillbikes.com CLASSIC / ENERGISE / VOGUE WARRANTY Westhill bikes are covered by a limited 3-year warranty.
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number for (2005-2008) Proper service and repair procedures are vital
More informationINSTALLATION INSTRUCTIONS
2012-2014 F-150 4 MyFord factory display 360º Vision System (Kit # AVMS-3604) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Video
More informationAttention! 1 Accessories. 2-1 Installation description ❹ ❺. Please proceed as follows
Thank you for purchasing the TNT-B meter for Yamaha Bolt. Before installing, please read the instruction carefully and keep it for future reference. Attention! For installation, please follow the steps
More informationVECTRIX VX-2 SERVICE MANUAL. Version 1.0/May 2011 VECTRIX, LLC
www.vectrix.com CONTENTS SECTION A: Tools 1 Tools Needed SECTION B: Mechanical Parts 1 Front Fairing 2 Front Console Cover 3 Speedometer Cover 4 Front Vertical Panel Cover-Lower 5 Front Vertical Panel
More informationInstallation. Instructions ES416. VW MKIV Golf/Jetta/GLI 337/20AE. to activate integral fog lights in Jetta GLX, E-Code, and HID Lighting Systems
Installation Instructions to activate integral fog lights in Jetta GLX, E-Code, and HID Lighting Systems This tutorial is provided as a courtesy by ECS Tuning. VW MKIV Golf/Jetta/GLI 337/20AE best viewed
More informationCLASSIC WINDSHIELD MOUNTING INSTRUCTIONS
CLASSIC WINDSHIELD MOUNTING INSTRUCTIONS INTRODUCTION These instructions contain important information regarding the proper installation and maintenance of your new RIFLE windshield. Read it completely
More informationInstallation Guide. Index
Update Alert: Firmware updates are posted to the web on a regular basis. We recommend that you check for firmware and/or install guide updates prior to installing this product. Installation Guide The XK09-PKN3
More informationTable of Contents. Bikes with 2 handlebar switches. 12-pin plug for BMW models Installation tips. 15-pin plug for older BMW models Installation tips
Table of Contents Bikes with 2 handlebar switches SM-5 12-pin plug for BMW models Installation tips 2 3 SM-6 15-pin plug for older BMW models Installation tips Special Features & Functions 4 5 4-Way Emergency
More informationMOTION-ACTIVATED WALL LANTERN
SIZE: 8.5in X 11in Portfolio is a registered trademark of LF, LLC. All rights reserved. ITEM #0358718 MOTION-ACTIVATED WALL LANTERN MODEL #VEL-5069-MD-PIR Français p. 9 Español p. 17 ATTACH YOUR RECEIPT
More informationConflicts: Vehicles without a sunroof Vehicles with a single sunroof
Toyota Sienna (Dual Sunroof) 2011-10.2 Overhead Video Part Number: 00016-00110 00016-00110-17 Fit Kit 00016-00120 00016-00120-17 Fit Kit Accessory Code: ED5 Conflicts: Vehicles without a sunroof Vehicles
More informationTOYOTA TACOMA XSP-X LED DRL. Part Number: Accessory Code: LDRL10
TOYOTA TACOMA 2013 - XSP-X LED DRL Part Number: 00016-35230 Accessory Code: LDRL10 Conflicts -None Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3 1 Harness bag 4 Hardware Bag
More informationInstallation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013
Installation Tips for your Crimestopper/ProStart Remote Start system (add-on for GM vehicles) v1.02 updated 1/16/2013 Thank you for purchasing your remote start from MyPushcart.com - an industry leader
More information