Landscape Pull Type Rakes

Transcription

1 Landscape Pull Type Rakes LRP05 & LRP15 Series LRP05 Series LRP15 Series M Operator s Manual! Read the Operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Copyright 2008 Printed 07/14/08 Cover photo may show optional equipment not supplied with standard unit.

2 Land Pride Important Safety Information Signal Words Safety Labels Introduction Application Using This Manual Terminology Definitions Owner Assistance Serial Number Plate Section 1: Assembly and Set-up Series LRP05 Landscape Rakes Series LRP15 Landscape Rakes LRP05 Grader Blade (Optional) LRP15 Grader Blade (Optional) Section 2: Operating Instructions Operating Instructions Section 3: Adjustments LRP05 & LRP15 Rake Angle LRP05 & LRP15 Lever Height Control LRP15 Turnbuckle Height Control LRP05 Flip Down Grader Blade (Optional) LRP15 Flip Down Grader Blade (Optional) Section 4: Maintenance and Lubrication 13 Maintenance General Lubrication LRP05 & LRP15 Lever Arm Pivot Point LRP15 Rear Axle Weldment Rake Teeth Rear Wheel Bearings Section 5: Options LRP05 & LRP15 Flip Down Grader Blade Section 6: Specifications & Capacities..15 Section 7: Features and Benefits Section 8: Appendix Torque Values Chart Notes Warranty Copyright 2008 All rights Reserved Land Pride provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. Land Pride is a registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. LRP05 & LRP15 Series Landscape Pull Type Rakes M 07/14/08

3 Land Pride Important Safety Information Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Safety at All Times Thoroughly read and understand the instructions given in this manual before operation. Refer to the Safety Label section, read all instructions noted on them. Do not allow anyone to operate this equipment who has not fully read and comprehended this manual and who has not been properly trained in the safe operation of the equipment.! Look For The Safety Alert Symbol The SAFETY ALERT SYMBOL indicates there is a potential hazard to personal safety involved and extra safety precaution must be taken. When you see this symbol, be alert and carefully read the message that follows it. In addition to design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in the operation, transport, maintenance and storage of equipment. Operator should be familiar with all functions of the unit. Operate implement from the driver s seat only. Do not leave tractor or implement unattended with engine running. Dismounting from a moving tractor could cause serious injury or death. Do not stand between the tractor and implement during hitching. Keep hands, feet, and clothing away from power-driven parts. Wear snug fitting clothing to avoid entanglement with moving parts. Watch out for wires, trees, etc., when raising implement. Make sure all persons are clear of working area. Turning tractor too tight may cause implement to ride up on wheels. This could result in injury or equipment damage. Be Aware of Signal Words A Signal word designates a degree or level of hazard seriousness. The signal words are:! DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is limited to the most extreme situations, typically for machine components that, for functional purposes, cannot be guarded. For Your Protection Thoroughly read and understand the Safety Label section, read all instructions noted on them.! WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and includes hazards that are exposed when guards are removed. It may also be used to alert against unsafe practices.! CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. Shutdown and Storage Lower machine to ground, put tractor in park, turn off engine, and remove the key. Detach and store implements in a area where children normally do not play. Secure implement by using blocks and supports. OFF REMOVE 07/14/08 LRP05 & LRP15 Series Landscape Pull Type Rakes M 1

4 Important Safety Information Land Pride These are common practices that may or may not be applicable to the products described in this manual. Use Safety Lights and Devices Slow moving tractors, selfpropelled equipment, and towed implements can create a hazard when driven on public roads. They are difficult to see, especially at night. Flashing warning lights and turn signals are recommended whenever driving on public roads. Use lights and devices provided with implement. Transport Machinery Safely Comply with state and local laws. Maximum transport speed for implement is 20 mph. DO NOT EXCEED. Never travel at a speed which does not allow adequate control of steering and stopping. Some rough terrains require a slower speed. Sudden breaking can cause a towed load to swerve and upset. Reduce speed if towed load is not equipped with breaks. Use the following maximum speed - tow load weight ratios as a guideline: 20 mph when weight is less than or equal to the weight of tractor. 10 mph when weight is double the weight of tractor. IMPORTANT: Do not tow a load that is more than double the weight of tractor. Use A Safety Chain A safety chain will help control drawn machinery should it separate from the tractor drawbar. Use a chain with the strength rating equal to or greater than the gross weight of the towed machinery. Attach the chain to the tractor drawbar support or other specified anchor location. Allow only enough slack in the chain to permit turning. Do not use safety chain for towing. Practice Safe Maintenance Understand procedure before doing work. Use proper tools and equipment, refer to Operator s Manual for additional information. Work in a clean dry area. Lower the implement to the ground, put tractor in park, turn off engine, and remove key before performing maintenance. Allow implement to cool completely. Do not grease or oil implement while it is in operation. Inspect all parts. Make sure parts are in good condition & installed properly. Remove buildup of grease, oil or debris. Remove all tools and unused parts from before operation. 2 LRP05 & LRP15 Series Landscape Pull Type Rakes M 07/14/08

5 Land Pride Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Prepare for Emergencies Be prepared if a fire starts. Keep a first aid kit and fire extinguisher handy. Keep emergency numbers for doctor, ambulance, hospital and fire department near phone. Wear Protective Equipment Protective clothing and equipment should be worn. Wear clothing and equipment appropriate for the job. Avoid loose fitting clothing. Prolonged exposure to loud noise can cause hearing impairment or hearing loss. Wear suitable hearing protection such as earmuffs or earplugs. Operating equipment safely requires the full attention of the operator. Avoid wearing radio headphones while operating machinery. Avoid High Pressure Fluids Hazard Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic lines. Use a piece of paper or cardboard, NOT BODY PARTS, to check for suspected leaks. Wear protective gloves and safety glasses or goggles when working with hydraulic systems. If an accident occurs, see a doctor immediately. Any fluid injected into the skin must be surgically removed within a few hours or gangrene may result. 911 Keep Riders Off Machinery Riders obstruct the operator s view, they could be struck by foreign objects or thrown from the machine. Never allow children to operate equipment. 07/14/08 LRP05 & LRP15 Series Landscape Pull Type Rakes M 3

6 Important Safety Information Land Pride Safety Labels Your Landscape Rake comes equipped with all safety labels in place. They were designed to help you safely operate your rake. 1. Read and follow label directions. 2. Keep all safety labels clean and legible. 3. Replace all damaged or missing labels. 4. Some new equipment installed during repair require safety labels to be affixed to the replaced component as specified by Land Pride. When ordering new components make sure the correct safety labels are included in the request. To order new labels go to your Land Pride dealer. 5. Refer to this section for proper label placement. To install new labels: a. Clean the area the label is to be placed. b. Spray soapy water on the surface where label is to be placed. c. Peel backing from label. Press firmly on surface. d. Squeeze out air bubbles with edge of a credit card C LRP05 & LRP15 Caution: Falling Rake or Moldboard Hazard C LRP05 Red Reflector C LRP15 Red Reflector 4 LRP05 & LRP15 Series Landscape Pull Type Rakes M 07/14/08

7 Land Pride Introduction Introduction Land Pride welcomes you to the growing family of new product owners. This Landscape Rake has been designed with care and built by skilled workers using quality materials. Proper assembly, maintenance, and safe operating practices will help you get years of satisfactory use from the rake. The parts on your LRP05 & LRP15 Landscape Rakes have been specially designed and should only be replaced with genuine Land Pride parts. See your local Land Pride Dealer for all your Landscape Rake replacement parts. Application The LRP05 and LRP15 Series Landscape Rakes are designed and built by Land Pride to perform final soil surface preparation and reshaping soil and/or aggregate profile. LRP05 Series rakes are offered in 4, 5, and 6 ft. working widths with pull type hitches for mounting to compact tractors in the 20hp range and ATV s. LRP15 Series rakes are offered in 5 ft. and 6 ft. working widths with pull type hitches for mounting to tractors with 17 to 35hp capabilities and ATV s. Both series offer angling capabilities to meet specific finishing needs, and an optional flip-down grader blade to expedite material distribution and contouring tasks. These Land Pride Landscape Rakes are perfectly suited for use by home owners, landscapers, contractors, and rental yards. They have applications at housing and road construction projects, golf courses, terracing sites, run-off control projects, and reforestation sights. See Features and Benefits and Product Specifications for additional information and performance enhancing options. Using This Manual This Operator s Section is designed to help familiarize you with safety, assembly, operation, adjustments, troubleshooting, and maintenance. Read this manual and follow the recommendations to help ensure safe and efficient operation. The information contained within this manual was current at the time of printing. Some parts may change slightly to assure you of the best performance. To order a new Operator or Parts Manual contact your authorized dealer. Manuals can also be downloaded, free-of-charge from our website at or printed from the Land Pride Service & Support Center by your dealer. Terminology Right or Left as used in this manual is determined by facing the direction the machine will travel while in use unless otherwise stated. Definitions NOTE: A special point of information that Land Pride feels an operator must be aware of before continuing. IMPORTANT: A special point of information related to its preceding topic. Land Pride s intention is that this information should be read and noted before continuing. Owner Assistance The Warranty Registration card should be filled out by the dealer at the time of purchase. This information is necessary to provide you with quality customer service. If customer service or repair parts are required contact a Land Pride dealer. A dealer has trained personnel, repair parts and equipment needed to service the Landscape Rake. These parts have been specially designed and should only be replaced with genuine Land Pride parts. Please consult you nearest Land Pride Dealer for replacement parts. Serial Number Plate Refer to the Figure 1 for the location of your serial number plate on both LRP05 & LRP15 Series Serial Number Plate Location Figure 1 For prompt service always use the serial number and model number when ordering parts from your Land Pride dealer. Be sure to include your serial and model numbers in correspondence also. Your dealer wants you to be satisfied with your new machine. If for any reason you do not understand any part of this manual or are not satisfied with the service received, the following actions are suggested: 1. Discuss the matter with your dealership Service Manager. Make sure he is aware of any problems you may have and that he has had the opportunity to assist you. 2. If you are still not satisfied, seek out the Owner or General Manager of the dealership, explain the problem and request assistance. 3. For further assistance write to: Product Support Land Pride, Service Department 1525 East North Street P.O. Box 5060 Salina, KS /14/08 LRP05 & LRP15 Series Landscape Pull Type Rakes M 5

8 Section 1: Assembly and Set-up Land Pride Section 1: Assembly and Set-up Series LRP05 Landscape Rakes Refer to Figure 1-1: 1. Insert 1 rake pivot pin (#10) welded to pull frame (#5) through pivot hole in rake assembly (#9) as shown. Secure with flat washer (#17), slotted hex nut (#15), and 7/32 x 2 cotter pin (#18). Tighten slotted nut to a snug fit. Do not torque slotted nut. 2. Insert 3/4 x 4 3/8 hitch pivot pin (#19) through welded pull frame (#5) and secure with 3/16 hair pin (#20) as shown. 3. Position rear axle weldment (#7) between side plates of rear axle pivot bracket (#2). Insert rear axle pivot shaft (#4) through rear axle pivot bracket and rear axle weldment (#2 & #7) as shown. Secure with 1/4 x 1 3/4 hex bolts (#12) and lock nuts (#13). Tighten to proper torque. 4. Assemble lift handle (#8) to pull frame (#5) and secure with cotter pin (#23) as shown. 5. Insert rear axle pivot lug (#3) between clevis lifting links (#6). Secure with 5/8 x 2 1/4 hex bolt (#11) and lock nut (#14) as shown. Tighten to a snug fit. Do not torque lock nut. 6. Attach Wheels (#22) to rear axle weldment (#7) and secure with flat washers (#16) and 5/32 x 1 3/4 cotter pins (#21). 7. Ropes (#1) are coiled and attached to lift handle (#9). Uncoil ropes when ready to use.! CAUTION! Always check to be sure that the slotted hex nut and cotter pin are in place to retain the rake before reversing the rake. If they are missing, the rake will fall off the frame while being rotated! LR05 Assembly Figure LRP05 & LRP15 Series Landscape Pull Type Rakes M 07/14/08

9 Land Pride Section 1: Assembly and Set-up Series LRP15 Landscape Rakes Refer to Figure 1-2: 1. Insert 1 rake pivot pin (#7) welded to pull frame (#4) through pivot hole in rake assembly (#3) as shown. Secure with flat washer (#16), slotted hex nut (#13) and 7/32 X 2 cotter pin (#17). Tighten slotted nut to a snug fit. Do not torque slotted nut. 2. Insert 3/4 x 4 3/8 hitch pivot pin (#19) through welded pull frame (#4) and secure with 3/16 hair pin (#20) as shown. 3. Position rear axle weldment (#5) between pull frame yoke arms (#4). Insert rear pull axle shaft (#2) through pull frame yoke arms (#4) and rear axle weldment (#5) as shown. Secure both left and right side of rear axle weldment (#5) with 3/8 x 1 3/4 hex bolts (#9) and lock nuts (#11). Tighten to proper torque. 4. Assemble lift handle (#6) to pull frame (#4) and secure with cotter pin (#22) as shown. 5. Insert free end of turn buckle assembly (#8) around the axle connecting link (#1). Secure with 5/8 x 2 1/2 hex bolt (#10) and nylock nut (#14) as shown. Tighten to a snug fit. Do not torque lock nut. 6. Attach Wheels (#21) to rear axle weldment (#5) and secure with lock washers (#15) and hex nuts (#12). Torque to proper torque.! CAUTION! Always check to be sure that the slotted hex nut and cotter pin are in place to retain the rake before reversing the rake. If they are missing, the rake will fall off the frame while being rotated! LRP15 Assembly Figure /14/08 LRP05 & LRP15 Series Landscape Pull Type Rakes M 7

10 Section 1: Assembly and Set-up Land Pride LRP05 Grader Blade (Optional) Refer to Figure Attach blade support arms (#2) to the right and left hand side of rake mount (#1) with 3/8 x 2 1/4 hex bolts (#7), 3/8 lockwashers (#14), and 3/8 hex nuts (#9) (four bolts per support arm). Tighten to proper torque. 2. Attach Blade-up Lock Pin (#15) to right and left hand Blade Support Arms with hair pin (#16) as shown. 3. Attach both right and left end of the Grader Blade (#4) to Blade Support Arms (#2) with 3/4 x 2 1/2 grade 5 hex bolts (#8) and locknuts (#10) as shown. Do not torque locknuts (#10). 4. Attach two hex coupler nuts (#11) with flat washer (#13) to each side plate weldment (#3) by inserting two 7/16 x 1 grade 5 hex bolts (#6) complete with lock washers (#12), and flat washers (#13) through each side plate bottom and top holes as shown. Do not torque. 5. Insert pivot pin (#5) welded to side plates (#3) through tubes located on both ends behind Grader Blade (#4). Make certain coupler nuts (#11) are positioned behind the grader blade. Secure with hair pins (#16). 6. Adjust hex coupler nuts (#11) against back side of grader blade and tighten bolts (#6) to proper torque LRP05 Grader Blade Assembly Right Hand Side Shown Figure LRP05 & LRP15 Series Landscape Pull Type Rakes M 07/14/08

11 Land Pride Section 1: Assembly and Set-up LRP15 Grader Blade (Optional) Refer to Figure Attach blade support arms (#16) to the right and left hand side of the rake mount (#20) with 3/8 x 2 3/4 hex bolts (#17), 3/8 lockwashers (#18), and 3/8 hex nuts (#19) (six bolts per support arm). Tighten to proper torque. 2. Attach Blade Lock Handle (#3) to the right and left hand Blade Support Arms with 1/2 x 3 grade 5 hex bolts (#2), lock washers (#14), and hex nuts (#15) as shown. Tighten to proper torque. 3. Insert pin (#1) through the top hole of both Blade Support Arms. Secure with attached hair pin (#9). 4. Attach both the right and left end of the Grader Blade (#11) to Blade Support Arm with 3/4 x 2 1/2 grade 5 hex bolts (#12) and locknuts (#13) as shown. Do not torque locknut (#13). 5. Attach two hex coupler nuts (#8) with flat washer (#6) to each side plate (#7) by inserting two 7/16 x 1 grade 5 hex bolts (#4) complete with lock washers (#5), and flat washers (#6) through each side plate bottom and top holes as shown. Do not torque until step Insert pivot pin welded to side plates (#7) through the tubes located on both ends behind the Grader Blade (#11). Make certain that the coupler nuts (#8) are positioned behind the grader blade. Secure with hair pins (#9) 7. Adjust hex coupler nuts (#8) against back side of grader blade and tighten bolts (#4) to proper torque LRP15 Grader Blade Assembly Right Hand Side Shown Figure /14/08 LRP05 & LRP15 Series Landscape Pull Type Rakes M 9

12 Section 2: Operating Instructions Land Pride Section 2: Operating Instructions Operating Instructions By now you should have thoroughly read your Operator s Manual and properly installed your Land Pride Landscape Rake to your tractor. Before you begin raking you should visually survey the work site to make sure it is safe and free of foreign obstacles. Also make certain that all irrigation heads, utility outlets, and other obstacles are properly marked. Please stop and do the above checks and preparations if you have not yet done so before you begin to rake. This is a must for your safety and for the safety of others. Now that you are properly briefed, your landscape rake is properly installed, and you have properly checked out your work site, it is time to begin raking. When transporting or travelling to and from work sites, make sure that the rake is in the fully raised position and not in contact with the ground. Select a safe speed and transport to your work site in such a manner that faster moving vehicles can pass you safely. A slow moving vehicle sign should be employed if you are using a public road or right-of way. Once you have safely arrived at your work site, stop the tractor, lock tractor brakes to prevent rolling, shut off tractor engine, and remove ignition key before dismounting. Adjust rake angle with the rake in the up position. Changing rake angle left or right will distribute extraneous and oversized material in furrows to the left or right. Adjusting rake angle to be straight across distributes material evenly across the width of the rake with slight furrowing produced at both ends of the rake. Set rake height by adjusting the control lever to the rear notch if you are ready to begin work. If not, leave the rake in the up position. Remount tractor to make a gear and engine rpm selection that will produce a safe suitable ground speed for your particular operating conditions. Begin working with the rake set in the lowered position unless you intend to travel a short distance without raking. In this situation, leave the rake up to travel and begin work by pulling on the handle to lower the rake. See Rake Height Adjustment in Section 3 on page 11 for a detailed description on using pull ropes for the LRP05. Additional adjustments may be required to achieve the desired affect you are wanting. Practice will help to consistently achieve that desired result you are after. Always keep safety uppermost in your mind and remember that before dismounting the tractor you must always set the park brake, turn off the tractor and remove the ignition key. If you must park on a hillside you should always chock the tractor wheels for an extra measure of safety. See Product Specifications on page 15 and Features and Benefits on page 16 for additional information on performance enhancing options. 10 LRP05 & LRP15 Series Landscape Pull Type Rakes M 07/14/08

13 Land Pride Section 3: Adjustments Section 3: Adjustments LRP05 & LRP15 Rake Angle Refer to Figure 3-1: Five holes are provided for angling the rake position either clockwise or counterclockwise in increments of 7 1/2 degrees for a total of 15 degrees either direction off center. Change rake angle by pulling hair pin (#1) from lock pin (#2), pull lock pin (#2) from pull frame (#3), and rotate rake frame(#4). Reset lock pin and hair pin after rotating rake frame. Raise the rake by first pulling on rope (#6) or by squeezing handle (#9) upward to release pressure induced by the spring loaded latch (#8) resting in the rear notch. Keeping rope (#6) tight, pull on rope (#7) to raise the spring loaded latch and continue pulling on rope (#7) to raise the rake. Lower the rake by pulling on rope (#6) to release pressure induced by the spring loaded latch (#8) resting against the front notch. Keeping rope (#6) tight, pull on rope (#7) to raise the spring loaded latch (#8) and slowly allow the rake to lower by keeping rope (#7) tight as the operator releases the rope slowly till spring loaded latch (#8) returns to the rear notch. Letting go of the rope too fast will cause the spring latch (#8) to catch in the middle notch instead of the rear notch. Use middle notch in the adjusting plate (#5) for making turns and gently dumping the load on the go. LRP15 Turnbuckle Height Control Refer to Figure 1-2 on page 7: Fine tune the LRP15 rake height by adjusting the turn buckle (#9) connecting the Lift Handle Arm (#7) to the rear axle weldment (#6). Rake Angling Series LRP05 Shown Figure LRP05 & LRP15 Lever Height Control Refer to Figure 3-1: There are three notches in the height adjusting plate (#5) for lowering and raising the rake. The rear notch sets the rake in its lowest position, the center notch raises the rake halfway up, and the front notch raises the rake all the way up. LRP05 Series are equipped with pull ropes to allow height adjustment from the tractor seat. LRP15 Series are not equipped with pull ropes due to weight of the rake elements. Pull ropes can be added to LRP15 rakes by the user. 07/14/08 LRP05 & LRP15 Series Landscape Pull Type Rakes M 11

14 Section 3: Adjustments Land Pride LRP05 Flip Down Grader Blade (Optional) Refer to Figure 3-2 The LRP05 grader blade (#1) may be stored in the up position when not in use. Remove hair pin (#2) and bladeup lock pin (#3) located in the blade support arms (#4). Carefully pivot blade up until hole (#5) in blade support bars align with blade-up lock pin holes (#6). Replace blade-up lock pins and hair pins. Lower grader blade by first removing hair pins (#2) from blade-up lock pins (#3). Support grader blade in the up position and remove blade-up lock pins (#3) Lower grader blade. Replace blade-up lock pins and hair pins in blade support arms (#4). LRP15 Flip Down Grader Blade (Optional) Refer to Figure 3-3: The LRP15 grader blade may be stored in the up position when not in use. Carefully pivot the blade upward until it contacts the blade lock handles (#1). A lock pin (#2) should be placed in the lower hole to insure that the grader blade remains securely in the raised position. Lower the blade by removing the lock pin from the lower hole and replace in upper hole. Pull blade lock handle (#1) to allow grader blade to flip down. Replace lock pin to store it for future use LRP05 Grader Blade Lock Up Position Figure 3-2 LRP15 Grader Blade Lock Up Position Figure LRP05 & LRP15 Series Landscape Pull Type Rakes M 07/14/08

15 Land Pride Section 4: Maintenance and Lubrication Section 4: Maintenance and Lubrication Maintenance General Proper service and adjustment is the key to long life of any implement. With careful and systematic inspection and lubrication you can avoid many costly repairs and downtime. Lubrication Lubrication Legend multi-purpose spray lube multi-purpose grease lube multi-purpose oil lube 50 Intervals at which lubrication is required 25 LRP05 & LRP15 Lever Arm Pivot Point (LRP05 shown) Grease lever pivot zerk every 25 hours Type of Lubrication: Multi-Purpose Quantity = Until grease begins to emerge. 25 LRP15 Rear Axle Weldment Grease rear axle weldment every 25 hours Type of Lubrication: Multi-Purpose Quantity = Generously 25 Rear Wheel Bearings Grease rear wheel bearings every 25 hours Type of Lubrication: Multi-Purpose Quantity = Generously Seasonally Rake Teeth Grease before extended non-use or seasonally Type of Lubrication: Multi-Purpose Quantity = Generously 07/14/08 LRP05 & LRP15 Series Landscape Pull Type Rakes M 13

16 Section 5: Options Land Pride Section 5: Options LRP05 & LRP15 Flip Down Grader Blade Note: LRP05 & LRP15 grader blade assemblies are complete with side plates and Mounting Arms A LRP0548 GRADER BLADE A LRP0560 GRADER BLADE A LRP0572 GRADER BLADE A LRP1560 GRADER BLADE A LRP1572 GRADER BLADE 14 LRP05 & LRP15 Series Landscape Pull Type Rakes M 07/14/08

17 Land Pride Section 6: Specifications & Capacities Section 6: Specifications & Capacities LRP05 &LRP15 Series Landscape Pull Type Rakes LRP0548 LRP0560 LRP0572 LRP1560 LRP1572 Rake Width Approximate Weight (lbs.) Pull Type Horsepower Rating Rake Height /2 16 1/2 Teeth Size 1/4 x 3/4 wide Angle and Position 1/4 x 3/4 wide 1/4 x 3/4 wide 5/16 x 1 wide 5/16 x 1 wide 5 Positions Up to 30 degrees Right or left 5 Positions Up to 30 degrees Right or Left Teeth Spacing 1 3/4 Centers 2 Centers Teeth Material High Carbon Spring Steel High Carbon Spring Steel Grader Blade Option Flip Down Self Supporting Grader Blade with Blade-up Locking Handles and locking pins Flip Down Self Supporting Grader Blade with Blade-up Locking Handles and locking pins 07/14/08 LRP05 & LRP15 Series Landscape Pull Type Rakes M 15

18 Section 7: Features and Benefits Land Pride Section 7: Features and Benefits Features Tractor HP range Various working widths 5 Forward angles (up to 30 degrees) High carbon spring steel teeth Individual Replaceable teeth Optional Grader Blade Moldboard Blade adaptable LRP05 &LRP15 Series Landscape Pull Type Rakes Pull Type Turnbuckle (LRP15 Only) LRP05 = HP LRP15 = HP Allows adaptability to many tractor sizes. LRP05 = 48, 60 & 72 LRP15 = 60 & 72 Vary how much material to move. Benefits Teeth have memory to spring back to shape. Replace a damaged tooth without removing all of the teeth. Adding a flip down grader blade allows one to move and level dirt as well as other materials. Moldboard Blade assembly can easily replace the rake assembly for more versatility to ones implement. Use with tractors, ATV s, utility vehicles, and golf carts. Ease of depth control. 16 LRP05 & LRP15 Series Landscape Pull Type Rakes M 07/14/08

19 Land Pride Section 8: Appendix Section 8: Appendix Bolt Head Identification Torque Values Chart Bolt Head Identification Bolt Size (Inches) Bolt Size (Metric) Grade 2 Grade 5 Grade 8 Class 5.8 Class 8.8 Class 10.9 in-tpi 1 N m ft-lb 3 N m ft-lb N m ft-lb mm x pitch N m ft-lb N m ft-lb N m ft-lb 1/4" M 5 X /4" M 6 X /16" M 8 X /16" M 8 X /8" M10 X /8" M10 X /16" M12 X /16" M12 X /2" M12 X /2" M14 X /16" M14 X l /16" M16 X /8" M16 X /8" M18 X /4" M18 X /4" M20 X /8" M20 X /8" M24 X " M24 X " M30 X /8" M30 X /8" M36 X /4" M36 X /4" in-tpi = nominal thread diameter in inches-threads per in. 1 3/8" N m = newton-meters 1 3/8" ft-lb= foot pounds /2" mm x pitch = nominal thread diameter in millimeters x 1 1/2" thread pitch Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above. 07/14/08 LRP05 & LRP15 Series Landscape Pull Type Rakes M 17

20 Section 8: Appendix Notes Land Pride 18 LRP05 & LRP15 Series Landscape Pull Type Rakes M 07/14/08

21 Land Pride Section 8: Appendix Warranty Land Pride warrants to the original purchaser that this Land Pride product will be free from defects in material and workmanship beginning on the date of purchase by the end user according to the following schedule when used as intended and under normal service and conditions for personal use. Overall Unit: One year Parts and Labor Rake Teeth: Considered wear items This Warranty is limited to the replacement of any defective part by Land Pride and the installation by the dealer of any such replacement part, and does not cover common wear items such as blades, belts, tines, etc. Land Pride reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship. This Warranty does not apply to any part or product which in Land Pride s judgment shall have been misused or damaged by accident or lack of normal maintenance or care, or which has been repaired or altered in a way which adversely affects its performance or reliability, or which has been used for a purpose for which the product is not designed. Misuse also specifically includes failure to properly maintain oil levels, grease points, and driveline shafts. Claims under this Warranty must be made to the dealer which originally sold the product and all warranty adjustments must be made through such dealer. Land Pride reserves the right to make changes in materials or design of the product at any time without notice. This Warranty shall not be interpreted to render Land Pride liable for damages of any kind, direct, consequential, or contingent to property. Furthermore, Land Pride shall not be liable for damages resulting from any cause beyond its reasonable control. This Warranty does not extend to loss of crops, any expense or loss for labor, supplies, rental machinery or for any other reason. No other warranty of any kind whatsoever, express or implied, is made with respect to this sale; and all implied warranties of merchantability and fitness for a particular purpose which exceed the obligations set forth in this written warranty are hereby disclaimed and excluded from this sale. This Warranty is not valid unless registered with Land Pride within 30 days from the date of purchase by the end user. 07/14/08 LRP05 & LRP15 Series Landscape Pull Type Rakes M 19

22 Corporate Office: P.O. Box 5060 Salina, Kansas USA