Air Mod-Kit Changing out the 7 poly wheels on the rear of the T78 to 8.5 rubber air tires TRIKKE
|
|
- Antony Nash
- 6 years ago
- Views:
Transcription
1 Air Mod-Kit Changing out the 7 poly wheels on the rear of the T78 to 8.5 rubber air tires.
2 T78-CS Air Mod-Kit Disclaimer This document was written by Trikke Tampa. It s of our own opinion and example of how to change out the rear wheels on a TRIKKE T78CS. This is not an official Trikke Tech, Inc document but is only a guide to be used as a reference. Trikke Tampa is not responsible for the consumers use of this document. Trikke Tampa will not be held responsible for any damages or injuries that may have resulted in the use of this document. It is to be used at your own risk and responsibility. If you have any questions or need clarification on any of these instructions please feel free to call us at during business hours. You may also us at andy@trikketampa.com
3 Tools Needed and Explanation of Task Figure 1 Tools Required 5mm hex wrench 3mm hex wrench 8mm socket wrench or adjustable wrench Pliers Explanation of Task The Trikke T78CS-GY is designed to accommodate the 7 poly wheels, 8 poly wheels or 8.5 rubber air tires. There are 3 brake pad axle positions on the frame to accommodate each different wheel diameter, see figure 2. The brake axle will need to be adjusted to the proper position depending on the wheel diameter being installed. Figure 2 This manual will give you step-by-step instructions for installing the 8.5 rubber air tire. To install the 7 or 8 poly wheel you can use these same instructions but utilize the appropriate brake axle position on the frame for the wheel being installed.
4 Overview Step 1 Remove existing poly wheels Step 2 Loosen brake cable Step 3 - Remove brake axle Step 4 Re-Position brake spring Step 5 Re-Install brake axle and pad Step 6 Install 8.5 air tire with spacers Step 7 Adjust brake cable tension Step 8 Test brakes
5 Step 1 Figure 1.1 See figure 1.1 Using two 5mm hex wrenches on each side of the wheel axle go ahead and remove the poly wheel and wheel spacers from the Trikke. Do not discard the spacers (steel barrel that spaces between the wheel and the frame) in case you change back to the 7 poly wheels. NOTE: The original or longer spacer is only used for the 7 poly wheels. The 8.5 wheel and 8 poly wheel require a shorter spacer (supplied with kit). Step 2 See figure 2.1 Loosen one of the 3mm screws that secure the clamp. Remove the other 3 mm screw that secures the brake cable clamp. Put in safe place for later re-installation. Swing the clamp out of the way to cause the wire brake cable to come lose as shown in figure 2.1. Figure 2.1
6 Step 3 Using a 5mm hex wrench and 8mm socket or adjustable wrench remove the 8mm hex nut on the opposite side of the brake axle. Pull the brake axle all the way out of the frame and put in a safe place for later use. Step 4 NOTE: Figure 4.1 Before moving the spring please read this procedure in it s entirety. It s important to note the direction the spring is installed. If installed upside down the brakes will not function properly. Figure 4.2 First, move one side of the spring to the furthest small spring hole away. This is the hole that accommodates (allows clearance) the 8.5 wheel diameter. Then move the other side of the spring to the adjacent hole. By not removing the spring from the Trikke it ensures you are properly installing the spring for the 8.5 wheel. Figure 3.1 Figure 4.1 Figure 4.2
7 Step 5 NOTE: Be sure to read this step, in it s entirety, to fully understand the task before proceeding. See figure 5.1 Re-install the brake axle from the outside of the Trikke towards the inside. While feeding the axle through be sure the axle is going through the center of the spring and then into the axle hole of the brake pad. As the brake axle exits the opposite side of the brake pad again be sure it goes through the center of the spring and then on through to the adjacent hole of the frame. The axle can be difficult to feed through so be patient and DO NOT use a hammer. If necessary you can use the 5mm hex wrench on the brake axle and twist back and forth while pushing and feeding the brake axle through. Once the brake axle is all the way through do not install the 8mm hex nut at this time. If you do then it will slightly squeeze the frame together making it difficult to get the 8.5 wheel installed. Figure 5.1
8 Step 6 See figure 6.1 It s imperative that you inflate the 8.5 air wheel to 80psi before proceeding. This ensures the tire is fully inflated before adjusting the brakes on the next step. From the outside of the frame insert the wheel axle into the wheel axle hole on the frame just far enough to put the first spacer on the axle as shown in Fig 6.1. Put the 8.5 wheel in place and feed the axle through the wheel, see Fig 6.2. NOTE: There is a spacer in the hub of the wheel between the bearings. It may be necessary to spin the wheel axle back and forth with your fingers to allow the wheel axle to go on through. Once through the wheel be sure to put the second spacer on the axle before feeding through the frame. There may be extra space between the wheel and frame but it will pull together when the wheel axle is tightened. Using two 5mm hex wrenches on each side of the axle go ahead and tighten snugly. Figure 6.1 Figure 6.2
9 Step 7 Install and tighten the 8mm hex nut on the brake axle while being careful not to over tighten. NOTE: Instead of using pliers it s preferable to use only your fingers to pull the slack out of the brake wire cable. However, it can be difficult and cumbersome so we illustrate using pliers. If you use pliers be extra careful not to squeeze too hard or you will fray the cable. See Fig 7.1 Carefully pull the slack out of the wire cable while ensuring that all the cable housing ends are properly seated in their recesses at the hand brake lever and cable stays on the steering column. Pull downwards on the brake wire cable to cause it to bend around the brake pad. This will help it to hold in place and give clearance for the brake cable clamp. While maintaining a gentle and steady pull on the brake cable and causing the brake pad to just touch the tire then use your other hand to swing the cable clamp back over the cable so you can re-install the 3mm screw. Continuing to use your other hand, re-install the 3mm screw using your 3mm hex wrench. Tighten both 3mm hex screws of the brake wire cable clamp to firmly hold the wire cable in place. Remove all tools and inspect your work. Figure 7.1 Figure 7.2
10 Step 8 Put the Trikke back in it s normal upright position. Squeeze the brake levers several times to stretch the brake wire cable. Raise each wheel off the ground and give it a spin to ensure the brake pad isn t rubbing the tire. If there is a slight or intermittent slight rub then that should work out after riding for a few minutes and working the brakes. If there is excess brake pad pressure against the tire then perform Step 7 again. End of task. Figure 7.1 Figure 7.2
Go-ped ESR750 / ESR750EX Rear Brake Installation Instructions
Go-ped ESR750 / ESR750EX Rear Brake Installation Instructions This kit provides all the parts you need to install a rear brake on your ESR750 or ESR750EX. It will not work on an ESR Sport, or other Go-ped
More information1. Get fork mounted in stand. You can leave it in the bike, but you must remove the wheel and front brake.
Tools Needed: Bike stand Lint free shop Towels 1.5mm Allen Key Pick Set Grease (We recommend Slick Honey) Oil Measuring Cup (with cc Scale) Small Metal Drift Shop Vise Oil Bucket 13mm Deep Socket (6 point)
More informationPontoon Assembly Instructions and manual. Read before using hoist.
Page 1 Pontoon Assembly Instructions and manual. Read before using hoist. For Models 32BL18, 32BL22, 32BL25 and 42BL28 R Model 32BL22 Shown Proudly Made in Michigan By NuCraft Metal Products 402 Southline
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-1 1973-87 CHEVROLET 1/2 TON 2WD Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to
More informationGiant Hydraulic Disc Brake System
Giant Hydraulic Disc Brake System INSTALLATION INSTRUCTI IMPORTANT NOTICE Contact the place of purchase or Authorized Giant Retailer for information on detail of installation and maintenance. Read this
More informationMonster Wagon. OWNER S MANUAL Model MH
OWNER S MANUAL Model MH1100-01 Warning: Not for recreational use - persons should never ride in cart Warning: Do not tow cart in excess of 15 mph - never tow behind car or truck Warning: Not for high speed
More informationAmtryke Model AM-12 & AM-16
Amtryke Model AM-12 & AM-16 Carton Contents Carefully remove and lay out all parts from the carton so as not to scratch or lose any parts or pieces. The shipping carton should contain the pictured items
More informationProduct Handbook FOR THE BLADEZ XTR Lite ELECTRIC POWER BOARD
Portable Electric Power Board Product Handbook FOR THE BLADEZ XTR Lite ELECTRIC POWER BOARD PLEASE BE SAFE WHEN RIDING... ALWAYS WEAR A HELMET AND OBEY ALL LAWS! Page 1 IMPORTANT PLEASE READ THIS BEFORE
More information07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES
MAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA 92807 714-630-0363 WWW.MAXTRACSUSPENSION.COM SALES@MAXTRACSUSPENSION.COM PRODUCT: K886764 07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES PARTS LIST QTY LIFT
More informationInstallation Instructions 1812 Folder Disk Clutch Retrofit Kit Martin Yale #WRA
Installation Instructions 1812 Folder Disk Clutch Retrofit Kit Martin Yale #WRA1812510 Background: Early production Martin Yale Model 1812 Folders were originally equipped with a spring-clutch type feed
More informationUTILITY CART. Owners Manual. Model FR With Removable Folding Sides
UTILITY CART With Removable Folding Sides Owners Manual Model FR1245-2 Important Safety Instructions Assembly Instructions Parts and Hardware Identification CAUTION: Read, understand and follow ALL instructions
More informationP4 CHAINSTAY INTEGRATED ROCKER BRAKE (CSIRB) INSTALLATION
P4 CHAINSTAY INTEGRATED ROCKER BRAKE (CSIRB) INSTALLATION TOOLS REQUIRED 2, 2.5, 3, 5 mm allen keys 8, 9 mm open faced cone wrench Pliers Cable cutters Torque wrench MATERIALS REQUIRED: 1 x P4 chainstay
More informationCALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL
CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment
More informationInstallation Instructions for Teraflex 2.5 Inch Lift Kit with Shocks (2010 Jeep Wrangler Unlimited)
Installation Instructions for Teraflex 2.5 Inch Lift Kit with Shocks (2010 Jeep Wrangler Unlimited) Installation Time: 6 Hours Tools Required: Floor Jack Jack Stands Ratchet Torque Wrench 15mm Socket 15mm
More informationINSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125
INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125 1968-81 CAMARO & FIREBIRD 10 & 12 BOLT W/"C" CLIPS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-3 1988-98 CHEVY K1500 4WD 10" DRUMS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time
More informationThis is the Unpacking Guide for the Optibike Pioneer Allroad electric bicycle. The Guide provides information required to remove the Allroad from the
This is the Unpacking Guide for the Optibike Pioneer Allroad electric bicycle. The Guide provides information required to remove the Allroad from the box and assemble it. If you have not assembled a bicycle
More informationUSER MANUAL. Keep this User Manual in the vehicle on which Halos are installed.
Keep this User Manual in the vehicle on which Halos are installed. USER MANUAL 3 IMPORTANT SAFETY INFORMATION The Halo is not intended to replace regular pressure-checks and tire maintenance practices
More informationCHAINGUARD REGAL ST COLOR
DESOTO/ REGAL HAULER PARTS LIST Item Part # Description QTY Item Part # Description QTY 1 11871 REFLECTOR KIT TRIKE 1 32 11764 FENDER BRACE 24" MWT 1 2 12199 SCREW #14 x 3/4 4 33 12176 NUT5/16-24 HEX 2
More informationAdult Car Plans. A comprehensive guide to help you build an official Soap Box Derby Adult Car
Adult Car Plans A comprehensive guide to help you build an official Soap Box Derby Adult Car 1 Table Of Contents Introduction...Page 3 Adult Car Floorboard...Page 4 Step One Steering Stop Installation...Page
More informationHow to install shifter style lever (Gen 1 & Gen
How to install shifter style lever (Gen 1 & Gen 2) Written By: The Hive 2017 service.bythehive.com Page 1 of 10 TOOLS: T25 Torx wrench (1) Cable cutter (1) M3 Hex wrench (1) 2017 service.bythehive.com
More informationAmTryke Adult Recumbent Model JT2000 #50-FC-2000
AmTryke Adult Recumbent Model JT2000 #50-FC-2000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable
More informationDODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION INSTRUCTIONS
Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD T-STYLE STEERING KIT INSTALLATION
More informationCHAINGUARD REGAL ST COLOR
DESOTO/ REGAL HAULER PARTS LIST Item Part # Description QTY Item Part # Description QTY 1 11871 REFLECTOR KIT TRIKE 1 32 11762 FENDER BRACE 20" MWT 1 2 12199 SCREW #14 x 3/4 4 11764 FENDER BRACE 24" MWT
More informationSTEERING COLUMN - TILT
STEERING COLUMN - TILT 1993 Toyota Celica 1993 STEERING Toyota - Steering Columns - Tilt Wheel Celica DESCRIPTION & OPERATION Tilt steering wheels incorporate an upper steering shaft, attached by a "U"
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A126-2 1988-98 C1500 2WD 10" REAR DRUM Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationPERFORMANCE SUSPENSION PARTS
PERFORMANCE SUSPENSION PARTS Introduction Air Lift Performance The purpose of this publication is to assist with the installation, maintenance and troubleshooting of this Chrysler LX, LD, LC Platform 300C,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A136-1 1976-86 AMC 20 AXLES WITH WARN FULL FLOATING AXLE CONVERSION Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationAEV30308AA Last Updated: 05/31/18. 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE
AEV30308AA Last Updated: 05/31/18 4 DUALSPORT sc SUSPENSION system for RAM 1500 air ride standard and rebel INSTALLATION GUIDE PLEASE READ BEFORE YOU START TO GUARANTEE A QUALITY INSTALLATION, WE RECOMMEND
More informationBag 1. Bag 1. Center Pivot. Center Pivot
8 00734 01901 5 Center Pivot Bag 1 3374 - Center Pivot Socket 4019 - Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the top clamp screws, then work the ball
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FOR A136 REAR DRUM TO DISC BRAKE CONVERSION KIT for 1970-75 Jeep, CJ SERIES with Dana 44 flanged axle Thank you for choosing STAINLESS STEEL BRAKES CORPORATION
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION REAR BRAKE CALIPER NOTE: For rear disc pad removal and installation, DO NOT disconnect brake hose from caliper (wire aside). Replace all pads on an axle if wear indicator on any
More informationPontoon Assembly Manual Read before using hoist
Page 1 Pontoon Assembly Manual Read before using hoist For Models 32BL18, 32BL22, 32BL25 and 42BL28 R Model 42BL25 Shown Proudly Made in Michigan By NuCraft Metal Products 402 Southline Rd. Roscommon,
More informationKit Chevrolet/GMC Heavy Duty. Installation Guide
Installation Guide Kit 57538 Chevrolet/GMC Heavy Duty Representative vehicle image MN-1034 (021810) ECR 9155 For maximum effectiveness and safety, please read these instructions completely before proceeding
More informationRevised BX-1000 BLACK MAX
Revised 8-22-12 BX-1000 BLACK MAX PLEASE READ THROUGH THE ENTIRE MANUAL BEFORE INSTALLING YOUR BRAKE SYSTEM WARNING - DO NOT USE BRAKE FLUID - USE ATF HYDRAULIC FLUID ONLY **IMPORTANT** DO NOT USE ANY
More informationQUICKIE 5 R Quick Guide. IMPORTANT! Read all Warnings and Instructions contained in the complete Owner s Manual prior to using this product.
QUICKIE 5 R Quick Guide IMPORTANT! Read all Warnings and Instructions contained in the complete Owner s Manual prior to using this product. Backrest Upholstery Back Canes Tire Seat Sling Handrim Angle-Adjustable
More information18SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines
8SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines KIT DESCRIPTION These service kits include all necessary parts to replace the low pressure fuel lines between the fuel filter housing and fuel
More informationA i r R i d e C o n v e r s i o n S y s t e m I n s t a l l a t i o n I n s t r u c t i o n s. kelderman air ride
A i r R i d e C o n v e r s i o n S y s t e m I n s t a l l a t i o n I n s t r u c t i o n s 800 334-6150 www.keldermanairride.com kelderman air ride The difference in the ride is like night and day Inside
More informationThanks for Ordering The Honda VLX Adjustable Lowering Kit from READ THIS BEFORE UNPACKING YOUR KIT!
Thanks for Ordering The Honda VLX Adjustable Lowering Kit from READ THIS BEFORE UNPACKING YOUR KIT! This instruction booklet contains detailed steps for installing the Adjustable Lowering kit on your Honda
More informationSUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R1 REAR DRUM TO DISC BRAKE CONVERSION KIT A130-3 JEEP CJ SERIES W/AMC-20 REAR AXLES AND 5 x 5-1/2" BOLT CIRCLE Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your
More informationSecond Stage Regulator - 1/4 Turn
Second Stage Regulator - 1/4 Turn MAINTENANCE AND REPAIR TAL 806 (L) Rev. 6 MSA 2008 Prnt. Spec. 10000005389 (I) Mat. 10042827 Doc. 10000015245 1/4 TURN SECOND STAGE REGULATOR SECOND STAGE REGULATOR COMPONENTS
More informationProduct Handbook. Electric Power Board. Powered Personal Transportation. FOR THE BLADEZ XTR Lite 250 ELECTRIC POWER BOARD
` Powered Personal Transportation Electric Power Board Product Handbook FOR THE BLADEZ XTR Lite 250 ELECTRIC POWER BOARD Model: PB-SM805-S PLEASE BE SAFE WHEN RIDING... ALWAYS WEAR A HELMET AND OBEY ALL
More informationOWNER S MANUAL Z SERIES TRACKS. Rev. 355_05
OWNER S MANUAL Z SERIES TRACKS Rev. 355_05 LOEGERING 800-373-5441 15514 37 th Street SE 701-347-5441 Casselton, ND 58012 USA Fax: 701-347-4323 E-Mail: lmi@loegering.com Internet: www.loegering.com Loegering
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A157 1991-2004 Dodge Dakota 2WD 1991-2002 Dodge Dakota 4WD 1998-2002 Dodge Durango Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for
More informationFIGURE 2 FIGURE 3 AFTER BEFORE
OUTBOARD Stud Location OUTBOARD Left hand bracket shown - Right hand side opposite Bolt Location Left Hand Side Air Port Left Hand Side UPPER BRACKET ASSEMBLY (Top View) FIGURE 2 FRONT NORMAL RIDE HEIGHT:
More informationCable Shift Linkage Kit
Cable Shift Linkage Kit INSTALLATION INSTRUCTIONS ididit column to Chrysler 727/904 Trans FOR PART NUMBER S: 2801700010, 2802700010 S INCE 1986 www.ididitinc.com 610 S. Maumee St., Tecumseh, MI 49286 PH:
More informationPet Bicycle Trailer/Jogger. Owner s Manual & Instructions
Pet Bicycle Trailer/Jogger Owner s Manual & Instructions Congratulations on your purchase of the Pet Bicycle Trailer/Jogger. Please read through this manual and following the instructions before and during
More informationNext, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles.
Next, chase the threads in the lower A-arm mounts with the 5/8-18 tap and blowout any remaining particles. Now, apply some anti-seize to the threads of the pivot stud. Also put anti-seize inside the bore
More informationAir Lift. Kits PERFORMANCE / /78637 BMW E36, E46 Chassis Rear Application (With and Without Shocks) INSTALLATION GUIDE
Air Lift PERFORMANCE Kits 75636/78636 75646/78637 BMW E36, E46 Chassis Rear Application (With and Without Shocks) INSTALLATION GUIDE PERFORMANCE SUSPENSION PARTS For maximum effectiveness and safety, please
More informationInstallation Manual TWM Performance Short Shifter Subaru Forester up to 2005
- 1 - Installation Manual TWM Performance Short Shifter Subaru Forester up to 2005 Please Note: It is preferable to park on a flat surface, as you will have to engage and disengage the hand brake and shift
More informationINSTALLATION INSTRUCTIONS FOR MOUNTING HARDWARE KIT F-105K2.5
MY SAFE T PLUS UNIT INSTALLATION INSTRUCTIONS FOR MOUNTING HARDWARE KIT F-105K2.5 This kit supports installation of SAFE T PLUS : MODEL # 41-140 (RED) MODEL # 41-180 (WHITE) MODEL #41-230 (BLUE) KEEP INSTRUCTIONS
More informationINSTALLATION & OWNER S MANUAL
Rev. R p. 1 of 16 INSTALLATION & OWNER S MANUAL V4211 HARD SIDED CAB KIT and/or V4275 CAMO HARD SIDED CAB KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner.
More information69-74 VW Beetle IRS Rear Kit Part No
www.airliftcompany.com 69-74 VW Beetle IRS Rear Kit Part No. 75615 MN-476 (01102) ECN 3455 Please read these instructions completely before proceeding with installation A C B E D AA F F ITEM QTY. PART
More informationInstallation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
More informationINTEGRAL POWER STEERING GEAR FORD Applies to F-100 F-350 (4X2), F-150 F-250 (4X4) And Bronco
Rockcrawler Steering Shop Manual page1 The following is from the Ford 1978 Truck Shop Manual, Volume 1 Chassis. It is provided here as a courtesy to classic Ford owners who would like to perform their
More informationSTEERING COLUMN - TILT
STEERING COLUMN - TILT 1994 Toyota Celica 1994 STEERING Toyota - Steering Column - Tilt Wheel Celica DESCRIPTION & OPERATION Tilt steering wheels incorporate a mainshaft, attached by a "U" joint to an
More informationINSTALLATION INSTRUCTIONS FOR FORD 4WD SUPER DUTY F COIL SPRING SUSPENSION SYSTEM
INSTALLATION INSTRUCTIONS FOR 2008-10 FORD 4WD SUPER DUTY F250-350 6 COIL SPRING SUSPENSION SYSTEM Requires the following parts (sold separately) for a complete installation: KIT PART NUMBER (6860) REQUIRES
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More informationYOU MUST WEAR SAFETY GLASSES DURING EACH STEP OF THESE INSTRUCTIONS
Machine Racer: Rally Preparation 1. Print the Working Drawing of the design you created and simulated in the Mousetrap Car 2.0 STEM Application. You can find your Working Drawing in the "Outputs" tab of
More informationInstallation instructions for IPS parking Brake Kit for 1996 to 2002 Viper
Installation instructions for IPS parking Brake Kit for 1996 to 2002 Viper WARNING Modification of your vehicle with the parts identified above may alter its stock performance; the buyer hereby expressly
More informationTSS Fit Kit Installation Instructions Timbersled Snow Bike System
TSS Fit Kit Installation Instructions Timbersled Snow Bike System Information needed before you start: Read the entire installation instructions before starting. The instruction sheet is universal for
More informationPORSCHE 928. PKT Installation 1.8. No air pump version. Air pump version
PORSCHE 928 PKT Installation No air pump version Air pump version 1.8 Tools Torque wrench 10mm socket 12mm socket 13mm socket 5mm allen socket 6mm allen socket 8mm allen key Caliper Supplies Blue Loctite
More informationEVO-3029B JL Rear Bolt-on Coilover Kit NV2514
EVO Manufacturing EVO-3029B JL Rear Bolt-on Coilover Kit NV2514 READ BEFORE INSTALLATION: Caution: This kit requires drilling and cutting of both metal and plastic. Wheel backspacing adjustments may be
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A125-2 1955-70 FULL SIZE CHEVROLET Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationKit 78631/ Hyundai Genesis Coupe
Kit 78631/ 78632 Hyundai Genesis Coupe Rear Application (with and without shocks) (011609) ERN 8124 INSTALLATION GUIDE For maximum effectiveness and safety, please read these instructions completely before
More informationAssembly Manual. 1/10th World GT car
Assembly Manual 1/10th World GT car Center Pivot Bag 1 3374 - Center Pivot Socket 40194 - Hard Anodized Alum Pivot ball 3254-2-56 Button Head *Note - Sometimes it is helpful to slightly over-tighten the
More informationFront Suspension - Front Stabilizer Bar Bushing Removal and Installation
1 of 3 23/02/2012 7:34 AM Front Suspension - Front Stabilizer Bar Bushing Removal and Installation Published: 11-May-2011 Removal WARNING: Make sure to support the vehicle with axle stands. Raise and support
More informationOWNER S MANUAL. LOEGERING th Street SE Casselton, ND USA Fax:
OWNER S MANUAL TRAIL BLAZERS and D SERIES TRACKS LOEGERING 800-373-5441 15514 37 th Street SE 701-347-5441 Casselton, ND 58012 USA Fax: 701-347-4323 E-Mail: lmi@loegering.com Internet: www.loegering.com
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A158 1994-97 Dodge Ram 1500 (2WD & 4WD) and REAR DISC BRAKE CONVERSION KIT A158-1 1998-01 Dodge Ram 1500 (2WD & 4WD) Thank you for choosing STAINLESS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A128-4 1997-2004 JEEP WRANGLER (TJ) WITH DANA 44 AXLES (non-abs) Thank you for choosing STAINLESS STEEL BRAKES for your braking needs. Pleases take the
More informationService Bulletin. HIITMill (X) Brake Lever Drift
HIITMill (X) Brake Lever Drift Applies to: HIITMill (9-4590) + HIITMIll X (9-4640) On some HIITMill and HIITMill X units, the brake lever can drift when the user is Rev. A applying load to the belt. This
More informationSUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS
XJ SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 7 page REAR SUSPENSION... 16 ALIGNMENT TABLE OF CONTENTS page AND WHEEL ALIGNMENT...1 DIAGNOSIS AND TESTING SUSPENSION
More informationKIT No , and 80590
KIT No. 80531, 80545 and 80590 by MN-354 (05603) ECR 5593 Please read these instructions completely before proceeding with installation Air Spring Kit Parts List Item Description Quantity A Air Spring
More informationKits 52420, 52440, 52445, and 52465
Universal Air Spring Spacer Kits 52420, 52440, 52445, 52460 and 52465 MN-1059 (011711) ERN 8773 Go to air-lift.co/liftspacer to determine which spacer is needed for your application. INSTALLATION GUIDE
More informationPLEASE BE SAFE WHEN RIDING... ALWAYS WEAR A HELMET AND OBEY ALL LAWS!
Powered Personal Transportation Electric Power Board Product Handbook FOR THE BLADEZ XTR Street ELECTRIC POWER BOARD Model: PB-SM1806 PLEASE BE SAFE WHEN RIDING... ALWAYS WEAR A HELMET AND OBEY ALL LAWS!
More informationSpecification Item Number / Model Name CK-5001T / Metropolis Patterson Transmission Crankset
CK-5001T Metropolis Patterson Transmission Crankset Installation Instructions Published May, 2015. ZSP001.v4 Full Speed Ahead Introduction Congratulations on your Full Speed Ahead product. Please read
More informationFinal Assembly Instructions Portside Cruiser
Final Assembly Instructions Portside Cruiser Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert cycling
More informationINSTALLATION & USER S GUIDE
INSTALLATION & USER S GUIDE RadiusCX Clutch for cable-actuated bikes Revision: 102617 2017 Rekluse Motor Sports Rekluse Motor Sports, Inc. customerservice@rekluse.com Table of Contents OVERVIEW... 3 INSTALLATION
More informationCorkSport ort Mazda 3 Adjustable Shifter Mazdaspeed 3, Mazda 3 6-speed and Mazda3 SkyActiv 6-speed
Part # Axl-6-963 CorkSport ort Mazda 3 Adjustable Shifter 2010-2013 Mazdaspeed 3, 2010-2013 Mazda 3 6-speed and 2012-2013 Mazda3 SkyActiv 6-speed Pre-Installation Notes: The CorkSport Adjustable Short
More informationAmTryke Adult Recumbent Model HP1000 #50-HC-1000
AmTryke Adult Recumbent Model HP1000 #50-HC-1000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable
More informationAssembly Manual. Assembly Instructions Read Carefully 2.1. Parts included: Tools suggested: Electric Drill
2.1 Assembly Manual Tools suggested: Parts included: Electric Drill 3/8ths bit 5/16ths bit Phillips screw driver Cutting pliers 1/2 inch socket wrench 1/2 inch wrench or crescent wrench 8 mm socket wrench
More informationKit No BT. FOR 6" C NOTCH BELL TECH Please read these instructions completely before proceeding with installation.
Kit No. 59106BT FOR 6" C NOTCH BELL TECH Please read these instructions completely before proceeding with installation. by MN-283 (061108) ECR 7136 Nylon Lock Nut Large Flat Washer Press Lock Elbow Fitting
More informationKit No Please read these instructions completely before proceeding with installation. Air Spring Kit Parts List. Attaching Hardware
Kit No. 57340 MN-431 (02409) NPR 4796 Please read these instructions completely before proceeding with installation by www.airliftcompany.com Air Spring Kit Parts List A B1 B2 Item Description Quantity
More informationKit Nissan Z34 370z Infiniti G37
Kit 75621 Nissan Z34 370z Infiniti G37 Rear Application (021510) ECR 8221 INSTALLATION GUIDE For maximum effectiveness and safety, please read these instructions completely before proceeding with installation.
More informationINSTALL MANUAL. FOR ON LINE ORDERING- E Commerce Visit Our Website
INSTALL MANUAL FOR ON LINE ORDERING- E Commerce Visit Our Website WWW.PRESSUREGUARD.COM Contact Information Technical Support: Chris@pressureguard.com Sales Support: Sales@pressureguard.com By Phone: 615-227-6024
More informationProduct Handbook. Electric Power Board. Powered Personal Transportation FOR THE BLADEZ ION 150 ELECTRIC POWER BOARD
Powered Personal Transportation Electric Power Board Product Handbook FOR THE BLADEZ ION 150 ELECTRIC POWER BOARD Model: PB-SM812 PLEASE BE SAFE WHEN RIDING... ALWAYS WEAR A HELMET AND OBEY ALL LAWS! IMPORTANT
More informationDisc Brake System ( For Cross-Country)
Technical Service Instructions General Safety Information Disc Brake System ( For Cross-Country) SI-8C60F t WARNING Please use extra caution to keep your fingers away from the rotating disc brake rotor
More informationTire Manual. Northern Tool Item #: Marathon Part #: Description: Pneumatic/Air Filled; 4.80/ ribbed; 5/8 bearing bore; 6 hub
Tire Manual Northern Tool Item #: 121022 Marathon Part #: 20001 Description: Pneumatic/Air Filled; 4.80/4.00-8 ribbed; 5/8 bearing bore; 6 hub Contents Safety Information... 3 Customer Service... 3 Tire
More informationBANANA PEEL OWNER'S GUIDE # /98 $1.00
BANANA PEEL OWNER'S GUIDE #1880 /98 $1.00 ILLUSTRATED PARTS BREAKDOWN ITEM PARJff DESCRIPTION QTY. ITEM PART# DESCRIPTION 1. 19171 SCREW #10-3 X 3/8 RHMS. 1863 FENDER B/P 3 3. 18306 FENDER B/P BRACE.
More informationSCION tc BIG BRAKE KIT Section I - Installation Preparation
SCION tc 2005- BIG BRAKE KIT Section I - Installation Preparation Part Number: PTR09-21080 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH Front 3 1 Brake Caliper
More informationFor all Ram x4 Trucks, and all Ram x4 trucks.
Dodge Off Road, LLC Specializing in Dodge Ram Solid-Axle 4x4 Suspension and Steering for Off Road Applications 855.9009.DOR sales@dodgeoffroad.com dodgeoffroad.com DODGE OFF ROAD 5 th GEN STEERING KIT
More informationJabiru J170/230/430/250/450 Constructors Manual. Pre-Paint>Fuselage>Undercarriage>Assemble main gear
Objectives of this task: In this task you will assemble the main undercarriage legs, which includes fitting the axles, disc brakes and wheels and adjusting the brakes. Materials required: Cards # J8 Dual
More informationAir Lift. Kit Ford Mustang SN95 PERFORMANCE INSTALLATION GUIDE. Rear Application
Air Lift PERFORMANCE Kit 78619 Ford Mustang SN95 Rear Application INSTALLATION GUIDE PERFORMANCE SUSPENSION PARTS For maximum effectiveness and safety, please read these instructions completely before
More informationBRK JL CC5 K Hydraulic Front Brake Kit For Club Car DS Model Installation Instructions
BRK JL CC5 K Hydraulic Front Brake Kit For Club Car 1982-2005 DS Model Installation Instructions Kit Components: A) Master Cylinder Mounting Bracket (x1) B) Master Cylinder Assembly (x1) C) Brake Line
More informationKit No Please read these instructions completely before proceeding with installation. Figure 1 MN-614 (06601) ECR
Kit No. 57291 MN-614 (06601) ECR 5445 Please read these instructions completely before proceeding with installation. by www.airliftcompany.com Figure 1 1 Hardware List Item Part No. Description Quantity
More informationGP1-R FULL EXHAUST SUZUKI GSX-R600 / GSX-R
THIS EXHAUST SYSTEM IS DESIGNED FOR USE IN CLOSED COURSE RACING ONLY, AND IS NOT INTENDED FOR PUBLIC HIGHWAY USE. IN THE STATE OF CALIFORNIA, IT IS ILLEGAL TO MODIFY THE EMISSION CONTROL SYSTEM ON ANY
More informationKits Installation Guide current Chevrolet Silverado HD and GMC Sierra HD. Watch the video Info on next page
S E R I E S TM Installation Guide 2011-current Chevrolet Silverado HD and GMC Sierra HD Kits 57338 88338 89338 Watch the video Info on next page For maximum effectiveness and safety, please read these
More informationRepresentative vehicle image
Installation Guide Kit 57589 Dodge/RAM Heavy Duty Representative vehicle image For maximum effectiveness and safety, please read these instructions completely before proceeding with installation. Failure
More informationA/C COMPRESSOR SERVICING Article Text 1991 Saab 9000 For Copyright 1997 Mitchell International Friday, October 15, :22PM
Article Text ARTICLE BEGINNING 1991 GENERAL SERVICING Compressor Service * PLEASE READ THIS FIRST * CAUTION: When discharging air conditioning system, use only approved refrigerant recovery/recycling equipment.
More information