CITY AND COUNTY OF SAN FRANCISCO Veh # EQUIPMENT SPECIFICATIONS FOR A THERMOPLASTIC SERVICE TRUCK 06/11/2012

Size: px
Start display at page:

Download "CITY AND COUNTY OF SAN FRANCISCO Veh # EQUIPMENT SPECIFICATIONS FOR A THERMOPLASTIC SERVICE TRUCK 06/11/2012"

Transcription

1 SECTION 3-FLATBED BODY: Furnish and install an extra heavy-duty steel flatbed body to the following approximate dimensions. FRAME AND FLOOR: Dimensions will be approximately 96 wide x 144 long. 7 gauge steel side and end rails. Longitudinal stringers shall be 2 x 4 x 3/16 tubing running the entire length of the deck. 4 I-beam cross members 12 on center. Heaviest duty available for this application. The flatbed shall be attached to the truck frame with a minimum of 3 shear plates per side. Attached with a minimum of two 5/8 diameter grade eight bolts to the truck frame. Decking shall be fabricated of 3/16 steel diamond plate. The rear potion of the bed shall have a ¼ smooth steel plate welded to the bed measuring approximately 76 long x 96 wide. Additional bracing shall mounted underneath the flatbed. Exact location of the support bracing shall be determined at the pre-build meeting. 1/2 Rope hooks on all crossmembers. Steel inboard stake pockets on each side of the frame rail. These pockets shall be spaced to accommodate the side fence western gates. Furnish and install two (2) anti-sail mud flaps just behind rear dual wheels and tires. Furnish and install two (2) aluminum mud flaps just forward of the rear dual wheels and tires. A dock type bumper shall be fabricated and installed upon the rear of bed. It shall be fabricated using minimum 6 C channel type steel. This bumper shall meet or exceed OMCS code The rear of the truck shall be equipped with a 2 tow receiver. A tow hook, Kerins K-300 Multi Hitch, 8 ton rated combination ball and pintle with square tube adapter, Kerins model K-650. This adapter shall be bolted to the K-300 hitch with grade 8 bolts, washers and nylok nuts. Ball shall be 2-5/16. Hitch height shall be set at 19 to center of ball. Rear hitch to include two D rings for attachment of trailer safety chains. The D rings shall be Fleet Engineers model # , mounted one each side of pintle hook receiver. These rings shall hang from bottom of bumper into open air, swing type. There shall be a 7-pin electrical connector, Cole Hersee model # with split pin, flush mount in bumper, and protective boot number 11178, mounted 12 to the drivers side of the hitch on bumper. HEADBOARD: Furnish and install a 1/8 diamond plate headboard with cutout for rear window. Headboard shall be built to withstand heavy-duty use. Cutout shall be covered with a minimum ¾ #9 expanded metal. Headboard shall be full width of bed and be at least 2 above cab. Headboard shall be fully framed with heavy-duty 4 channels. Page 13 of 25

2 SIDE FENCE: There shall be two (2) removable fence western gate. All sections shall be fabricated using 1 x 6 hardwood slats ( bottom slats to be two 1 x 6 = 12 high, steel stakes and western gate locks The western gate fences shall be mounted toward the front of flat bed. A horizontal pipe ½, (with ends flattened and welded to the steel stakes), shall act as lifting supports on the outside of each rack section. Fence shall be the same height as the headboard. The two front fences shall interlock with the headboard. CHAIN RAILING: A post and chain railing shall be installed around the center of the platform just behind the front western gates. The steel railing will be constructed of 1-1/2 square tubing and be 42 high in order to meet OSHA requirements. The ladder entrance areas shall be able to be closed off with a safety chain. SIDE LADDERS: Two fold-up ladders on each side of the bed. The ladders shall be capable of being locked in the down position and also have the capability of being locked in the up position. The step treads shall be fabricated from grip strut material. Both ladders shall have a threestep ladder, 16 wide, installed just behind the chain railing, around the center of the flat bed, passenger and driver side. Two steel grab handles shall be mounted above the ladders on the left and right side of the bed. Furnish and install one (1) fixed access ladder positioned to give access to the rear of bed. PLATFORM: There shall be a 2 x 8 platform of adequate height to facilitate loading of the kettles. TOOL BOXES: Furnish and install two (2) 48 x 18 x 18 steel tool box, (or as large as space permits) Box- Master weather proof style with lockable handle that a # five size Master padlock will fit. The toolbox shall be frame mounted to driver s and passenger side, just behind side ladders. Two ¼ holes for drainage in the bottom of each toolbox. Boxes to have door chains. Two (2) storage bins shall be install on the rear of the truck. One storage bin to be above the deck to the rear of the kettles and one to be bellow the deck between the frame rails at the rear of the deck. Exact dimensions shall be determined at the pre-bid meeting. Page 14 of 25

3 AUXILIARY LIGHTING AND SAFETY ITEMS: The tail, brake, back-up, and running lights shall be LED. A Superior Signal model SY810LED, 55 long by 13 high with amber LED lamps shall be mounted just behind the kettles on a heavy-duty riser. This arrow board shall be raised approximately 48 high x 96 wide and be clearly visible from the rear of truck. Framing for the vertical uprights shall be a 2 x 2 x 1/4 steel square tubing. The horizontal cross bar shall also be 2 x 2 x ¼ steel square tubing. On the base of the vertical risers shall be a 2 ½ x 2 ½ x 3/16 square tube, approximately 12 high. The vertical tubes shall be inserted into this square tubing, welded to the floor board and welded to the vertical tubes. Controller for arrow board shall be mounted within easy reach of driver. Controller shall not be mounted on the floorboard of cab. Exact height of riser shall be determined at the prebid meeting. Controllers shall be controlled through the Diamond Logic switches. This switch shall be the first switch from the left and be labeled REAR ARROW BOARD. Arrow Board shall be protected through an appropriate size automatic circuit breaker. A second Superior Signal model SY810LED, 55 long by 13 high with amber LED lamps shall be mounted on top of the cab protector. This arrow board shall be raised so as to be visible from the front of the vehicle. Controller for arrow board shall be mounted within easy reach of driver. Controller shall not be mounted on the floor of cab. Exact height of riser shall be determined at the pre-bid meeting. Controller shall be controlled through the chassis factory Diamond Logic switches. This switch shall be the second switch from the left and be labeled FRONT ARROW BOARD. Arrow Board shall be protected through an appropriate size automatic circuit breaker. Furnish two Whelen model # L31HAF LED amber beacons with brush guard Whelen model #L360BGB mounted on the top corners of arrow board risers. Rear beacons shall be controlled through the chassis factory Diamond Logic switches. This switch shall be the third switch from the left and labeled REAR BEACONS. These beacon lights shall be protected through an appropriate size automatic circuit breakers. Furnish one Whelen model # L31HAF LED amber beacon with brush guard Whelen model #L360BGB mounted on top of the cab visible from the front, passenger and driver side. Front beacon shall be controlled through the chassis factory Diamond Logic switches. This switch shall be fourth from the left and labeled FRONT BEACON. Four work lights, 12 volt Betts model with clear flood bulb model 4466 shall be furnished and installed on the truck. The front work lights shall mounted on top of cab protector, outer front corners of the cab protector. The two rear work lights shall be mounted on the underside of rear beacon riser cross bar. The front work lights shall be controlled through the chassis factory Diamond Logic switches. This switch shall be the fifth switch from the left, labeled FRONT WORK LIGHTS. The rear work lights shall be controlled through the Diamond Logic switches. This switch shall be the sixth switch from the left and labeled REAR WORK LIGHTS. Additional turning indicators shall be mounted, one on each side of the bed, located at the lower front corners of the bed. These lights shall be Truck-Lite, Super 60 Page 15 of 25

4 series, kit number # 60115Y amber in color. The lights shall also activate with the marker lights. It shall be acceptable to allow these side turn signal lights to be mounted integrally into the side rails without the use of the brackets or off set to the underside of the truck bed. These side light shall take the place of any OEM mounted side lights. The right turn signal shall be equipped with an audible alarm, Preco model # LDA50. This shall be accomplished by wiring the right turn audible alarm through the right front turn signal. Furnish and install a Provision back up camera model TV-505 A full system with 7 LCD color monitor, to allow the operator to see what is behind the vehicle. A 5-lb Amerex model 500 fire extinguisher with mounting bracket 861H shall be installed as close as possible to the driver s side door. The fire extinguisher shall be mounted so the control handle is toward the rear of the truck. Standard Brand first aid kit, model # 34-25PFG 1` mounted inside cab. Dietz 3-flare holder with 30 minute flares installed inside the cab near driver s compartment. Vehicle shall be equipped with a Preco back-up alarm model # 1060 bac-a-larm. A set of triangular hazard reflectors shall be furnished and installed, located behind the passenger seat. ATTENTION: All wiring to all electrical systems shall be routed through protective conduit and be weatherproof. Wiring shall have adequate protective covers wherever there is a possibility of contact with any other components. Separators shall be used where applicable. No tape or adhesive fasteners will be accepted. All wiring shall be routed to be clear of all heat sources and shall be protected from any present or potential source of snags, abrasions or sharp edges. All controls, control panels. warning gauges, and switches shall be marked as to function with stamped or engraved stainless steel or aluminum labels. All electrical loads shall be protected through automatic circuit breakers, appropriately sized to load and labeled as to function. Note: It shall be the responsibility of the successful bidder to communicate with the manufacture of all the electrical accessories and equipment being outfitted on the truck so that the appropriate wiring, connectors, switches, control panels, and circuit breakers can be determined. NOTE: See attached diagram for layout specifics. FINISH: The body shall be primed with a rust inhibitor and painted automotive type paint, gloss black in color. The entire understructure shall be undercoated. Before painting, all surfaces must be cleaned of rust, oil, grease, dirt, mills scales, other foreign materials. Page 16 of 25

5 WARRANTY: Body shall be warranted for 12 months parts and labor with no deductible charges. Warranty shall commence when the City accepts delivery of vehicle. SECTION 4 THERMOPLASTIC KETTLES: The thermoplastic tank on the kettle shall be cylindrical in shape, vertically mounted, have a minimum capacity of 2000 pounds, and shall be capable of heating blocks and granulated thermoplastic. The kettles shall be bolted through the framing of the flatbed and chassis. The tanks shall be heated indirectly by a diesel fired gun type burner with a minimum rating of 250,000 BTU. There shall be an electric start to ignite the burners on the kettles. A hinge cover shall be placed in a position as to guard the diesel burner assemblies. This cover shall be hinged from the top, attached to the burner heat shield, fold down and latch to the top of the deck. Final design shall be approved at the first inspection trip. These kettles shall be mounted towards the rear on the deck of the flat bed truck, The transfer chute shall discharge thermoplastic towards the rear to the truck. The minimum length of the chutes shall be approximately 42 long and 32 from the end of chute to ground level. Exact dimensions shall be determined at the first inspection trip. Furnish and install a right angle 3 threaded male pipe on the output of the kettles. Furnish a Molasses valve, McMaster Carr 3 NPT female, part # , delivered loose. The burner shall be vented at the top of the kettle, each vent shall be provided with a rain cap to prevent rain from entering the heating chamber. Heat transfer shall be by #46 heat transfer oil contained by an insulated jacket surrounding the thermoplastic tank. The heat transfer fluid tank shall be equipped with a level indicator to indicate the proper level of the heat transfer oil and shall be properly vented to prevent pressure buildup. Agitator shall be driven by a hydraulic motor rotating a minimum of 30 RPM, a clearance between the agitator blades and the side of the tank not to be more than one-quarter (1/4) of an inch. Each agitator shall be equipped with two or more blades and reverse agitator. A flow control valve shall be provided to adjust the speed of the agitator without changing the speed of the engine. Direct reading thermometer to indicate the thermoplastic temperature shall be marked THERMOPLASTIC. Direct reading thermometer to indicate the heat transfer fluid temperature shall be marked HEAT TRANSFER FLUID. Burner shall be controlled by an adjustable temperature controller with a digital temperature readout of the heat transfer oil. Page 17 of 25

6 A safety shutoff shall be installed to shut off fuel and the gun burner in the event the gun burner does not ignite and maintain combustion. Extended handle on the discharge valve at least seven inches in length to facilitate operation from ground level. Discharges trough at least 24 inches in length. All controls for the auxiliary engine and the kettles shall be placed next to the ladder entrance on the curb side of the equipment deck as to be seen by the operator from ground level. Both kettles and auxiliary engine shall draw fuel from the chassis fuel tank. Plumbing shall meet or exceed all DOT & NFDA regulations. Both kettles and auxiliary engine shall operate a minimum single 12 hour work shift without refueling. All fittings, hoses, and fuel lines shall be routed through protective tubing and shall have adequate protective covers wherever there is a possibility of contact with any other components. All fuel lines shall be routed to be clear of all heat sources and be protected from any present or potential source of snags, abrasions or sharp edges. All fuel lines shall be securely fastened to chassis using heavy-duty type fasteners. AUXILIARY ENGINE: Shall be EPA certified 2008 Tier 4 diesel fueled engine, Yanmar model # 2TNV70-ASA rated at 13.7 HP, 23.8 ft-lb of 2600 RPM, four (4) cycle, water-cooled with sufficient horsepower to operate the agitator shall be furnish and installed or approved equal. This engine shall be Bio-Diesel B20 compatible. The engine shall be a volt system, equipped with an electric starter, approved air cleaner, muffler, 40 amp alternator, and a variable speed governor. Auxiliary engine shall be enclosed inside a open aired compartment, with the dimension approximately 26 wide x 90 long with enough height clearance for engine size. The top cover shall provide access to the engine compartment and have an automatic hold-open device(s). Cover shall be fully hinged with stainless steel piano hinge. Engine compartment shall be equipped with a hasp capable of accepting a #6 Master brand pad lock. The engine compartment shall be securely anchored to the sub-floor. The cover shall be made of heavy-duty diamond plate and have anti-skid material applied on the entire top surface of the engine cover. The front, left, and right sides of engine compartment shall be fabricated from # 9 expanded metal to allow air flow for the auxiliary engine. Framing shall be heavy-duty angle iron. Rear portion of engine compartment shall be a solid piece of diamond plate material. This engine compartment shall have the capacity to support two (2) 300-lb person. Exhaust fumes shall directed away from any work station area. Exact location of tail-pipe shall determined at the pre-bid meeting. Any exposed exhaust pipe that has the potential to come into contact with personnel or other areas of the truck shall be covered by a stainless steel shield. Page 18 of 25

7 Auxiliary engine shall have an independent battery for starting and operation of auxiliary engine. Battery shall be isolated from chassis batteries. Battery shall be charge through the auxiliary engine alternator. Fuel supply to auxiliary engine shall be from the factory chassis fuel tank. Plumbing shall meet or exceed all DOT & NFDA regulations. All fittings, hoses, and fuel lines shall be routed through protective tubing and shall have adequate protective covers wherever there is a possibility of contact with any other components. All fuel lines shall be routed to be clear of all heat sources and be protected from any present or potential source of snags, abrasions or sharp edges. An in-line fuel filter shall be installed between the fuel tank and auxiliary engine, with a minimum micron rating of 10. This fuel filter shall be easily accessible for maintenance. All fuel lines shall be securely fastened to chassis using heavyduty type fasteners. Hydraulic pump shall be coupled directly to this engine, mounted under equipment deck. HYDRAULIC: The hydraulic system shall be a positive displacement pump. Furnish and install a directional control valve. Furnish and install an appropriate hydraulic pump that shall be rated to produce at least 1 ¼ the amount of flow and pressure required to power the agitators of both kettles. Furnish and install a hydraulic reservoir tank with enough capacity to operate the agitators. The fill orifice shall be clearly labeled in English as to the contents and type of hydraulic oil. The tank shall have a drain on the bottom of the tank that shall allow fluid to drain unobstructed to the ground. This drain plug shall have at least a ¾ plug. Tank exit line shall be controlled with a stainless steel ¼ turn type ball valve. Tank shall have a spin on/off type filter on the return side. The filter shall be isolated on both side of the filter housing with ¼ turn stainless steel ball type valve. The hydraulic tank shall have a site gauge for full fluid level, temperature and pressure gauge located adjacent to the hydraulic tank. All hydraulic hoses shall be machined crimped hose fittings. ELECTRIC HEATER: Overnight temperature maintenance shall be provided with an electric heater capable of maintaining the product at a minimum of 150ºF. Maximum power source for the electric heater shall not exceed 120 volts. MISCELLANEOUS: Kettles shall have adequate guards to cover moving parts. Vehicles shall have placard, stencils and decals indication potential hazards. Shall have easy access to service the battery, engine, hydraulic filter, and hydraulic reservoir. Page 19 of 25

8 TRAINING: Successful bidder shall provide a qualified instructor(s) on the operations and safety procedures of the Thermoplastic Kettles. This class shall be for a minimum of one (1) 8 hour work day for at least five (5) City of San Francisco equipment operator personnel. Training shall take place at a City specified location. Successful bidder shall provide a qualified instructor(s) to conduct training class(es) on the mechanical repairs of the Thermoplastic Kettles. This class shall be for a minimum of one (1) 8 hour work day for two (2) City of San Francisco mechanical personnel. Training shall take place at a City specified location. MANUALS: Two (2) complete set of operator s, repair, and parts manual shall be supplied with the completed unit upon delivery. These manuals shall include all hydraulic and electric diagrams. Complete set of manuals for the auxiliary engine shall also be supplied. WARRANTY: The auxiliary engine, hydraulic system, and kettles shall be warranted for a period of one (1) year, parts and labor with no deduction. This warranty shall commence when the City accepts delivery of vehicle. PAINT: All exposed metal surface shall be cleaned and prepared to be primed with a rust and heat preventative and finished in a high heat resistant paint. DOCUMENTATION: Bidders shall provide with their bid response: Detailed concept installation drawing of the proposed installation, and stability calculation using the Trailer Win software program and detailed weight distribution. Failure to supply such with the bid submission shall disqualify the prospective bidder. Page 20 of 25

9 REAR ARROWBOARD FACTORY MULTIPLEX SWITCH PANEL FRONT ARROWBOARD REAR BEACONS FRONT BEACONS DRAWING NOT TO SCALE FRONT WORK LIGHTS REAR WORK LIGHTS Page 21 of 25

10 ATTACHMENT D BID EXCEPTION SHEETS Return with Bid if any exceptions are taken Please Note: All exceptions to the City s bid requirements must be listed on the sheets provided. Only those exceptions that are listed on the sheets provided will be evaluated. Any material exceptions may result in the rejection of the bid and the bidder will not receive further consideration. *Section Title, Line Number, & Page Number Description Page 22 of 25

11 Page 23 of 25

12 Page 24 of 25

13 Page 25 of 25

CITY AND COUNTY OF SAN FRANCISCO Veh # EQUIPMENT SPECIFICATIONS FOR A THERMOPLASTIC SERVICE TRUCK 06/19/2012

CITY AND COUNTY OF SAN FRANCISCO Veh # EQUIPMENT SPECIFICATIONS FOR A THERMOPLASTIC SERVICE TRUCK 06/19/2012 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 SPECIAL: Furnish and install a Pro-gard,

More information

Line Body Canopy and Accessories:

Line Body Canopy and Accessories: ATTACHMENT A Heavy Crew Truck Line Body and Accessories Installation. TMWA provided cab & chassis specifications are provided on last page The Cab & Chassis will be a Freightliner (All Other Items Referenced

More information

SPECIFICATIONS FOR TRUCK EQUIPPED WITH AERIAL LIFT AND SERVICE BODY Pennsylvania Department of Military and Veteran Affairs

SPECIFICATIONS FOR TRUCK EQUIPPED WITH AERIAL LIFT AND SERVICE BODY Pennsylvania Department of Military and Veteran Affairs Page 1 of 5 SPECIFICATIONS FOR TRUCK EQUIPPED WITH AERIAL LIFT AND SERVICE BODY Pennsylvania Department of Military and Veteran Affairs Insulated Telescopic Articulating type aerial lift with the following

More information

RUGGED CONSTRUCTION SUPERIOR DESIGN IN TRUCK BODY FABRICATION

RUGGED CONSTRUCTION SUPERIOR DESIGN IN TRUCK BODY FABRICATION RUGGED CONSTRUCTION SUPERIOR DESIGN IN TRUCK BODY FABRICATION A DIVISION OF PB9600 STANDARD PLATFORM/ STAKE BODIES SHOWN EQUIPPED WITH 12' Body with Optional Wood Floor Triple Window in Bulkhead Stake

More information

STATE OF MINNESOTA PRICING Page % DISCOUNT

STATE OF MINNESOTA PRICING Page % DISCOUNT TRAILERS: DUMP BODY, LOWBOYS, FLATBED, TAG, SLIDE AXLE, UTILITY, GOOSENECK, ENCLOSED, ETC. Vendor Name: Truck Utilities Inc Contact Person: Paul Warner Street Address: 2370 English Street P.O. Box: City,

More information

GRANITE SERIES TRUCK BED

GRANITE SERIES TRUCK BED GRANITE SERIES TRUCK BED GRANITE TRUCK BED DETAILS Flatbed is available in 7' - 8'6" - 9'4" - 11'4" lengths Skirted flatbed with integrated tool boxes Polyester powder coated steel diamond-plate deck,

More information

NOTICE OF BID. The City of Pigeon Forge is receiving bids on three trucks for the Public Works Department.

NOTICE OF BID. The City of Pigeon Forge is receiving bids on three trucks for the Public Works Department. NOTICE OF BID The City of Pigeon Forge is receiving bids on three trucks for the Public Works Department. Specifications may be obtained from the Public Works Department in City Hall between the hours

More information

One (1) New Trailer Mounted Thermoplastic Pavement Marking Unit Bid No Notice to Bidders

One (1) New Trailer Mounted Thermoplastic Pavement Marking Unit Bid No Notice to Bidders CITY OF SAN LEANDRO INVITATION FOR BIDS SUBMIT BID TO: City of San Leandro Purchasing Department 835 East 14th Street San Leandro, CA 94577 FOR FURTHER INFORMATION CONTACT: Julie Jenkins Purchasing Agent

More information

ACCEPT ONLY THE BEST

ACCEPT ONLY THE BEST ACCEPT ONLY THE BEST Cab & Chassis The truck shall be supplied by the customer. CET Fire Truck Glider kit #7 Revised January 10 th 2018 The glider kit is made for dual rear wheels truck with a «back-of-cab-to

More information

NOTICE OF BID. The City of Pigeon Forge is receiving bids on four trucks for the Public Works Department.

NOTICE OF BID. The City of Pigeon Forge is receiving bids on four trucks for the Public Works Department. NOTICE OF BID The City of Pigeon Forge is receiving bids on four trucks for the Public Works Department. Specifications may be obtained from the Public Works Department in City Hall between the hours of

More information

City of New Haven. 101 FRONT STREET PO BOX 236 NEW HAVEN, MO Phone * * Fax

City of New Haven. 101 FRONT STREET PO BOX 236 NEW HAVEN, MO Phone *  * Fax City of New Haven 101 FRONT STREET PO BOX 236 NEW HAVEN, MO 63068 Phone 573-237-2349 * www.newhavenmo.org * Fax 573-237-4696 August 20, 2014 Request for Bids, Medium Duty Truck City of New Haven The City

More information

and Original Series Pickup Lift Mounting Instructions T-150-T T-150 PART#5177 T-150-T

and Original Series Pickup Lift Mounting Instructions T-150-T T-150 PART#5177 T-150-T Fullsize Chevy & GMC Trucks- 988-999 Toyota Tundra- 2000-2006 Toyota T-00-993-999 Preparing the Gate r ve and Original Series Pickup Lift Mounting Instructions. Remove the mounting hardware which is banded

More information

ALLEGAN COUNTY ROAD COMMISSION SPECIFICATION FOR BIDS

ALLEGAN COUNTY ROAD COMMISSION SPECIFICATION FOR BIDS ALLEGAN COUNTY ROAD COMMISSION SPECIFICATION FOR BIDS PROPOSAL FOR DUMP BOX BODIES, V BOX SPREADERS, UNDER BODY SCRAPERS, PLOW WINGS, FABRICATION AND ASSEMBLY OF COUNTY DUMP TRUCKS Board of County Road

More information

and Original Series Pickup Lift Mounting Instructions Fleetside Chevy & GMC Trucks Fleetside 4-door Chevy & GMC Trucks T-100

and Original Series Pickup Lift Mounting Instructions Fleetside Chevy & GMC Trucks Fleetside 4-door Chevy & GMC Trucks T-100 r ve and Original Series Pickup Lift Mounting Instructions Fleetside Chevy & GMC Trucks - 1960-1987 Fleetside 4-door Chevy & GMC Trucks - 1988-1991 Preparing the Gate 1. Remove the mounting hardware which

More information

and Original Series Pickup Lift Mounting Instructions Fullsize Chevy & GMC Trucks: 1500 & 2500 LD HD & 3500HD BOLT-ON GUSSET

and Original Series Pickup Lift Mounting Instructions Fullsize Chevy & GMC Trucks: 1500 & 2500 LD HD & 3500HD BOLT-ON GUSSET r ve and Original Series Pickup Lift Mounting Instructions Fullsize Chevy & GMC Trucks: 1500 & 2500 LD 1999-2007 2500HD & 3500HD 2000-2007 Preparing the Gate 1. Remove the mounting hardware which is banded

More information

and Original Series Pickup Lift Mounting Instructions Fullsize Nissan Titan Trucks present T-420 BOLT-ON GUSSET PART#5257

and Original Series Pickup Lift Mounting Instructions Fullsize Nissan Titan Trucks present T-420 BOLT-ON GUSSET PART#5257 and Original Series Pickup Lift Mounting Instructions Fullsize Nissan Titan Trucks- 2004-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket

More information

Appendix A - Group 8 SPECIFICATION, JEA CLASS 122+: ONE TON SRW 4X4 8 UTILITY BODY Extended Cab Unit UPDATED August 10, 2018

Appendix A - Group 8 SPECIFICATION, JEA CLASS 122+: ONE TON SRW 4X4 8 UTILITY BODY Extended Cab Unit UPDATED August 10, 2018 1. SCOPE It is the intent of the JEA to purchase EIGHT (8) ONE Ton FORD F-350 Extended Cab SRW 4X4 with BRAND FX 56LS 8 COMPOSITE UTILITY BODYs with Various Configurations, Up-Fits and Options. All units

More information

G-170. r ve Pickup Lift Mounting Instructions Fullsize Chevy & GMC Trucks- 1500, 2500 & 3500: 2007-present

G-170. r ve Pickup Lift Mounting Instructions Fullsize Chevy & GMC Trucks- 1500, 2500 & 3500: 2007-present Fullsize Chevy & GMC Trucks- 1500, 2500 & 3500: 2007-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket kit (Figure 1 and Table 1). 18-5/8"

More information

Specification Sheet Form Rev

Specification Sheet Form Rev 10000 CDC S1 Sales Administration Use Only Quote Number Quote Revision Shop Order Number Serial Number(s) Date CUSTOMER SALESPERSON MODEL : Customer Name : Salesperson Name : 10000 CDC S1 PART NO./DRAWING

More information

STATE OF MINNESOTA PRICING Page % DISCOUNT

STATE OF MINNESOTA PRICING Page % DISCOUNT STATE OF MINNESOTA PRICING Page % DISCOUNT Contract end Date March 1, 2018 TRAILERS: DUMP BODY, LOWBOYS, FLATBED, TAG, SLIDE AXLE, UTILITY, GOOSENECK, ENCLOSED, ETC. Vendor Name: Truck Utilities Inc Contact

More information

2. Compartments 2 compartments with gallons front to rear with double bulkheads

2. Compartments 2 compartments with gallons front to rear with double bulkheads January 10, 2016 STE # 11602 & 11605 (Ref. QT 3098/STE#10741-10744) ST&E SPECIFICATIONS FOR 4,000 US GALLON DOT-407 DOUBLE CONICAL STAINLESS STEEL INSULATED TWO COMPARTMENT TANDEM TRANSPORT TANK PREPARED

More information

SELF DRILL SCREWS FILLER STRIP

SELF DRILL SCREWS FILLER STRIP r ve Pickup Lift Mounting Instructions Fullsize Ford Trucks- F-150 2015-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket kit (Figure

More information

FLORIDA SHERIFFS ASSOCIATION, FLORIDA FIRE CHIEFS ASSOCIATION, & FLORIDA ASSOCIATION OF COUNTIES

FLORIDA SHERIFFS ASSOCIATION, FLORIDA FIRE CHIEFS ASSOCIATION, & FLORIDA ASSOCIATION OF COUNTIES P a ge 1 FLORIDA SHERIFFS ASSOCIATION, FLORIDA FIRE CHIEFS ASSOCIATION, & FLORIDA ASSOCIATION OF COUNTIES *Effecitive dates for Bid 15-11-0116 are: February 1, 2015 through March 31, 2016. SPECIFICATION

More information

Appendix A - Group 7 SPECIFICATION, JEA CLASS 119+: ONE TON SRW 4X4 PICKUP Extended Cab Unit UPDATED August 10, 2018

Appendix A - Group 7 SPECIFICATION, JEA CLASS 119+: ONE TON SRW 4X4 PICKUP Extended Cab Unit UPDATED August 10, 2018 1. SCOPE It is the intent of the JEA to purchase TWO (2) ONE Ton FORD REGULAR GAS EXTENDED CAB SRW 4X4 Pickup Trucks with Various Configurations, Up-Fits and Options. [ONE LWB 8 and ONE SWB 6 6 ] All Units

More information

SNOW PLOW, FRAME, HYDRAULIC SYSTEM, DUMP BODY, WING, SPREADER AND PRE-WET TANK SYSTEM

SNOW PLOW, FRAME, HYDRAULIC SYSTEM, DUMP BODY, WING, SPREADER AND PRE-WET TANK SYSTEM DEKALB COUNTY HIGHWAY DEPARTMENT SNOW PLOW, FRAME, HYDRAULIC SYSTEM, DUMP BODY, WING, SPREADER AND PRE-WET TANK SYSTEM Sealed proposal for the furnishing and installing of snow plow, frame, hydraulic system,

More information

Flashing Arrow Panel - 615/815 T/Y

Flashing Arrow Panel - 615/815 T/Y Flashing Arrow Panel - 615/815 T/Y All LED 15-Lamp Portable Flashing Arrow Panel Product Specifications American Signal Company FAP X 15 Page 1 of 8 6/11/17 2755 Bankers Industrial Drive Atlanta, GA 30360

More information

IC-35-D. Engineering Spec. Page 1 of 8 Date: June 2006

IC-35-D. Engineering Spec. Page 1 of 8 Date: June 2006 Engineering Spec IC-35-D Page 1 of 8 Replaces: Form HD14D Dated: May 24 BMC s IC-35-2D is a Self-Propelled Industrial Crane designed for in-plant lifting and material handling applications. It has special

More information

Specification Sheet Form Rev

Specification Sheet Form Rev Sales Administration Use Only Customer Quote Number Quote Revision Shop Order Number Serial Number(s) Date : Customer Name Salesperson Model : Salesperson Name : 8400 DDC S1 Part / Drawing Number : 730-8400

More information

IC-20-G. Engineering Spec. View thousands of Crane Specifications on FreeCraneSpecs.com. Page 1 of 7 Date: June 2006

IC-20-G. Engineering Spec. View thousands of Crane Specifications on FreeCraneSpecs.com. Page 1 of 7 Date: June 2006 Engineering Spec IC-20-G Page 1 of 7 Replaces: Form BD104G Dated: May 2004 The IC-20-1G is a self-propelled industrial crane designed for in-plant lifting and material handling applications. It is powered

More information

APPENDIX A GROUP 2 SPECIFICATION, JEA CLASS 116: HALF TON 4X2 SWB (6 6 Bed) PICKUP TRUCK Standard Cab Units UPDATED JUNE 12, 2018

APPENDIX A GROUP 2 SPECIFICATION, JEA CLASS 116: HALF TON 4X2 SWB (6 6 Bed) PICKUP TRUCK Standard Cab Units UPDATED JUNE 12, 2018 1. SCOPE It is the intent of the JEA to purchase FIFTEEN (15) HALF-TON 4X2 Standard Cab SWB (6 6 Bed / ALL UNITS) Pickup Trucks with Various Configurations, Up-Fits and Options. [15 Standard Cab]. All

More information

Pyrolance, LLC SPECIFICATIONS FOR DIESEL ENGINE DRIVEN ULTRA HIGH PRESSURE FIRE FIGHTING SYSTEM B2000 M-D

Pyrolance, LLC SPECIFICATIONS FOR DIESEL ENGINE DRIVEN ULTRA HIGH PRESSURE FIRE FIGHTING SYSTEM B2000 M-D SPECIFICATIONS FOR DIESEL ENGINE DRIVEN ULTRA HIGH PRESSURE FIRE FIGHTING SYSTEM B2000 M-D 1 HIGH PRESSURE FIRE FIGHTING SPECIFICATIONS Scope and General Design Requirements A fire fighting system shall

More information

T-52. r ve Pickup Lift Mounting Instructions Chevy / GMC- Colorado/ Canyon: 2015-present. Preparing the Gate. Installing the Bolt-on Gussets

T-52. r ve Pickup Lift Mounting Instructions Chevy / GMC- Colorado/ Canyon: 2015-present. Preparing the Gate. Installing the Bolt-on Gussets Chevy / GMC- Colorado/ Canyon: 2015-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting bracket kit (Figure 1 and Table 1). LEFT BRACKET (RIGHT

More information

TENDER 2019 OR 2020, ONE AND A HALF TON EXTENDED DOUBLE CAB/CHASSIS, 4X4, DUMP BODY TRUCK

TENDER 2019 OR 2020, ONE AND A HALF TON EXTENDED DOUBLE CAB/CHASSIS, 4X4, DUMP BODY TRUCK Municipality of the County of Colchester Recreation Department 1 Church Street, Truro, NS B2N 3Z5 Telephone: (902) 897-3185 TENDER 2019 OR 2020, ONE AND A HALF TON EXTENDED DOUBLE CAB/CHASSIS, 4X4, DUMP

More information

SECTION AXIAL HVAC FANS

SECTION AXIAL HVAC FANS SECTION 233413 - AXIAL HVAC FANS 1. PART 1 GENERAL 1.1. RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification

More information

EQUIPPED WITH. 3/8 Rubrail On Many Models LED Lighting Plug & Play Modular Sealed Wiring Harness Solid One Piece Rear Tailboard

EQUIPPED WITH. 3/8 Rubrail On Many Models LED Lighting Plug & Play Modular Sealed Wiring Harness Solid One Piece Rear Tailboard 8/9/16 EQUIPPED WITH BUILT TO WORK. BUILT TO LAST. Due to our unparalleled value proposition, CM Truck Beds has become a product of choice for commercial fleets and work truck users for many years. Whether

More information

650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present

650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present Installing the Base Plate 1. Examine the interior

More information

Heavy-Duty Truck Bodies and Truck Tool Boxes for Tree Care and Landscape Professionals

Heavy-Duty Truck Bodies and Truck Tool Boxes for Tree Care and Landscape Professionals Heavy-Duty Truck Bodies and Truck Tool Boxes for Tree Care and Landscape Professionals THE FIRST CHOICE IN: Chip Bodies Utility Tree Vehicles UTV Truck Tool Boxes Landscape Bodies A CUT ABOVE THE REST

More information

1. SCOPE 2. MODEL: 3.1 Base Curb Weight: not to exceed 7800 lbs. PAGE 1 OF 6

1. SCOPE 2. MODEL: 3.1 Base Curb Weight: not to exceed 7800 lbs. PAGE 1 OF 6 1. SCOPE It is the intent of the JEA to purchase FOUR (4) 3/4 Ton LWB Pickup / Utility Trucks with various up-fits and options (two (2) Fleet Side Pickup Bodies and two (2) Utility Bodies). All units must

More information

ABS Components Air Compressors Air Dryers & Cartridges Air Tanks. Air Disc Brakes Bearings Brake Pads Brake Rotors Brake Shoes & Kits Camshafts & Kits

ABS Components Air Compressors Air Dryers & Cartridges Air Tanks. Air Disc Brakes Bearings Brake Pads Brake Rotors Brake Shoes & Kits Camshafts & Kits Air Brake Systems ABS Components Air Compressors Air Dryers & Cartridges Air Tanks Air Valves Brass Fittings Composite Fittings Coiled Air Hoses Glad Hands Nylon Tubing Rubber Hoses Tire Valves Brake &

More information

GALLATIN PUBLIC UTILITIES

GALLATIN PUBLIC UTILITIES GALLATIN PUBLIC UTILITIES Bid Proposal Item: Single Axle Dump Truck Bid Date: Company Address: Phone Number: Manufacturer: Bid Information (1) Prices F.O.B., 249 Hancock Street, Gallatin, Tennessee 37066.

More information

OUR TRUCKS OFF-ROAD FUEL/LUBE TRUCKS MECHANICS TRUCKS... 3 LIGHT DUTY SERVICE BODY TRUCKS... 5 VACUUM TRUCKS LIGHT DUTY DUMP TRUCKS...

OUR TRUCKS OFF-ROAD FUEL/LUBE TRUCKS MECHANICS TRUCKS... 3 LIGHT DUTY SERVICE BODY TRUCKS... 5 VACUUM TRUCKS LIGHT DUTY DUMP TRUCKS... OUR TRUCKS During the past 85 years, we have grown into one of America s largest manufacturers and dealers of commercial service vehicles. We deliver internationally, with sales and service provided throughout

More information

Cantilever Series Mounting Instructions Fullsize Sprinter Van (US) All except WB (AA) present

Cantilever Series Mounting Instructions Fullsize Sprinter Van (US) All except WB (AA) present Fullsize Sprinter Van (US) All except 3500 144 WB (AA)- 2007-present Preparing the Gate 1. Remove the platform, mounting kit, license plate assembly, and bridge assemblies, which are banded to the main

More information

Price per loaded mile for delivery $ 2.25 Delivery Time Frame in calendar days ARO

Price per loaded mile for delivery $ 2.25 Delivery Time Frame in calendar days ARO Flatbeds Contract end Date 09-30-18 Vendor Name: Contact Person: Street Address: P.O. Box: City, State, Zip Phone #: Toll Free #: Fax #: Email Address: Website: Bert's Truck Equipment, Inc Jim McLaughlin

More information

2014 HEIL DOT407AL 9240GL, DOUBLE CONICAL, TANDEM AXLE, CRUDE OIL TRANSPORT WITH PUMP & CENTRIFUGE NV1309 VIN: 5HTDL4527D7H45530

2014 HEIL DOT407AL 9240GL, DOUBLE CONICAL, TANDEM AXLE, CRUDE OIL TRANSPORT WITH PUMP & CENTRIFUGE NV1309 VIN: 5HTDL4527D7H45530 2014 HEIL DOT407AL 9240GL, DOUBLE CONICAL, TANDEM AXLE, CRUDE OIL TRANSPORT WITH PUMP & CENTRIFUGE NV1309 VIN: 5HTDL4527D7H45530 VESSEL 1) Design Two piece barrel, 5454-H32 aluminum alloy for shell. 5454-0

More information

Hale Trailer Brake & Wheel Heil

Hale Trailer Brake & Wheel Heil Hale Trailer Brake & Wheel Heil 711061-711070 Model Code Capacity Compartments Shape Shell Material Head Material Operating Pressure Barrel Description APXS 1040-1, Aluminum, Pneumatic dry bulker, Interior

More information

PLATFORM BODIES. Platform Bodies. Made in the USA VERSATILE DURABLE RUGGED

PLATFORM BODIES. Platform Bodies. Made in the USA VERSATILE DURABLE RUGGED PLATFORM BODIES Made in the USA Platform Bodies VERSATILE DURABLE RUGGED Platform Bodies Premium materials, superb craftsmanship, and advanced production techniques make Reading Platform Bodies the preferred

More information

650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present

650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior

More information

M-B Companies, Inc. Specification. Model 245. Self Propelled Intermediate Striper. High Pressure Airless. Options. Revised September 27, 2006

M-B Companies, Inc. Specification. Model 245. Self Propelled Intermediate Striper. High Pressure Airless. Options. Revised September 27, 2006 M-B Companies, Inc. Administration Pavement Marking Equipment Divisions 1615 Wisconsin Avenue EAST COAST DIVISION WEST COAST DIVISION P.O. Box 200 79 Montgomery Street 2490 Ewald S.E. New Holstein, WI

More information

APPENDIX A GROUP 6 SPECIFICATION, JEA CLASS 122: ONE TON SRW 4X4 PICKUP

APPENDIX A GROUP 6 SPECIFICATION, JEA CLASS 122: ONE TON SRW 4X4 PICKUP ( Asset Coordinator Truck) 1. SCOPE It is the intent of the JEA to purchase ONE (1) ONE Ton FORD DIESEL EXTENDED CAB SRW 4X4 Pickup Truck 8 BED with Various Configurations, Up-Fits and Options. Unit must

More information

M-B Companies, Inc. Specification. Model 155 PLS-155. Palletized Striper. High Pressure Airless. 2 x 55 Gallon Drum. Standard Rev. 2 January 11, 2008

M-B Companies, Inc. Specification. Model 155 PLS-155. Palletized Striper. High Pressure Airless. 2 x 55 Gallon Drum. Standard Rev. 2 January 11, 2008 M-B Companies, Inc. Administration Pavement Marking Equipment Divisions 1615 Wisconsin Avenue EAST COAST DIVISION WEST COAST DIVISION P.O. Box 200 79 Montgomery Street 2490 Ewald S.E. New Holstein, WI

More information

SPECIFICATION, JEA CLASS 133+ UP-FITS, DESIGN/BUILD: FLATBED/CAB GUARDS, REEL ATTACHMENTS, FABRICATION / ASSEMBLY ETC. UPDATED July 05, 2018

SPECIFICATION, JEA CLASS 133+ UP-FITS, DESIGN/BUILD: FLATBED/CAB GUARDS, REEL ATTACHMENTS, FABRICATION / ASSEMBLY ETC. UPDATED July 05, 2018 1. SCOPE It is the intent of the JEA to award a contract to DESIGN/BUILD/INSTALL Flatbeds with Cab Guards, Three Independently Removable Reel Stands with Complete Tow Package/Off-Road Hitch Assembly s

More information

ADDENDUM 3 - APPENDIX A - TECHNICAL SPECIFICATIONS ONE (1) 3 TON 4X2 CARGO REEL CAB/CHASSIS

ADDENDUM 3 - APPENDIX A - TECHNICAL SPECIFICATIONS ONE (1) 3 TON 4X2 CARGO REEL CAB/CHASSIS 1. SCOPE It is the intent of the JEA to purchase ONE (1) 3T 4X2 CARGO REEL REGULAR CAB/CHASSIS (Chassis Only). Truck Chassis must be tested and delivered to JEA Fleet Facility (5717 New Kings Road Jacksonville,

More information

INSP Aerial Periodic Inspections

INSP Aerial Periodic Inspections The Aerial Periodic Inspection course features five individual segments covering the Terex Utilities Aerial Platform Periodic Inspections. The training outlines the Terex Utilities inspection form as well

More information

KM 8000 TEDD SPECIFICATION

KM 8000 TEDD SPECIFICATION KM 8000 TEDD SPECIFICATION Table Contents Technical Product Specifications Item 1 KM International KM 8000TEDD Asphalt Hotbox Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 Section 7 Section

More information

TOWN OF FARRAGUT. Bid Specifications For 2017 Dump Truck. William McKelvey Public Works Director Municipal Center Drive Farragut, TN 37934

TOWN OF FARRAGUT. Bid Specifications For 2017 Dump Truck. William McKelvey Public Works Director Municipal Center Drive Farragut, TN 37934 TOWN OF FARRAGUT Bid Specifications For 2017 Dump Truck William McKelvey Public Works Director TOWN OF FARRAGUT 11408 Municipal Center Drive Farragut, TN 37934 (865) 966-7057 BID SPECIFICATIONS for 2017

More information

REQUEST FOR QUOTE. Half Ton Trucks CONTRACT NO ADDENDUM NO.2

REQUEST FOR QUOTE. Half Ton Trucks CONTRACT NO ADDENDUM NO.2 REQUEST FOR QUOTE Half Ton Trucks CONTRACT NO. 19-130080-01 ADDENDUM NO.2 ISSUE DATE: March 15, 2019 1.0 GENERAL This addendum forms part of the contract documents and is to be read, interpreted and coordinated

More information

Specialists in Aluminium & Steel Tray Bodies. Contents

Specialists in Aluminium & Steel Tray Bodies. Contents Specialists in Aluminium & Steel Tray Bodies Duratray Transport Equipment are manufacturers of quality aluminium and steel tray bodies and associated accessories. Duratray have implemented a quality assurance

More information

P Original Series Cargo Van Lift Mounting Instructions Fullsize Ford Van present. Preparing the Gate

P Original Series Cargo Van Lift Mounting Instructions Fullsize Ford Van present. Preparing the Gate Fullsize Ford Van- 1992-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting kit (Figure 1 and Table 1). S-400-40 STRAP VAN MOUNTING EAR BENT BRACKET

More information

BID FOR A ONE (1) ONE-TON AND A HALF (5500 SERIES) CREWCAB TRUCK WITH DUMP BED. BID OPENING February 15, 2017 AT 10:00 A.M.

BID FOR A ONE (1) ONE-TON AND A HALF (5500 SERIES) CREWCAB TRUCK WITH DUMP BED. BID OPENING February 15, 2017 AT 10:00 A.M. P. O. B o x 1 5 4 0 T h o m a s v i l l e, G A 3 1 7 9 9 2 2 9-2 2 7-7 0 0 0 F A X 2 2 9-2 2 7-3 2 4 3 w w w. t h o m a s v i l l e. o r g BID FOR A ONE (1) ONE-TON AND A HALF (5500 SERIES) CREWCAB TRUCK

More information

9,000 lb. Forklift w/tire Changing Attachment (Propane) Req. 18-GA Georgia Ports Authority. Section 3 - Performance Specs Page 1 of 7

9,000 lb. Forklift w/tire Changing Attachment (Propane) Req. 18-GA Georgia Ports Authority. Section 3 - Performance Specs Page 1 of 7 In this Request For Sealed Bid, the "Required" column means that the bidder must comply with the specifications as indicated, or will be considered non-responsive. The specifications in the "Desired" column

More information

Bid Specifications HP935WCU PORTABLE AIR COMPRESSOR

Bid Specifications HP935WCU PORTABLE AIR COMPRESSOR Bid Specifications HP935WCU PORTABLE AIR COMPRESSOR GENERAL: TANDEM AXLE; STANDARD Working weight 10400 lbs 4717 kg Length 203.5 5.169 m Width 79.6 2.022 m Height 93 2.362 m Track 65.2 1.656 m Tire Size

More information

COLLEGE COMMUNITY SCHOOL DISTRICT BID SHEET. THREE (3) 78 PASSENGER TRANSIT STYLE SCHOOL BUSES and ONE (1) 65 PASSENGER LIFT BUS

COLLEGE COMMUNITY SCHOOL DISTRICT BID SHEET. THREE (3) 78 PASSENGER TRANSIT STYLE SCHOOL BUSES and ONE (1) 65 PASSENGER LIFT BUS COLLEGE COMMUNITY SCHOOL DISTRICT BID SHEET THREE (3) 78 PASSENGER TRANSIT STYLE SCHOOL BUSES and ONE (1) 65 PASSENGER LIFT BUS Bid #1 Three (3) 2010 (78) Passenger Transit Style School Buses and One (1)

More information

1. SCOPE 2. MODEL: 3. CHASSIS (CREW CAB 4X4 DIESEL) 3.1 Base Curb Weight: not to exceed 7000 lbs. 3.2 WB: / Short Wheel Base.

1. SCOPE 2. MODEL: 3. CHASSIS (CREW CAB 4X4 DIESEL) 3.1 Base Curb Weight: not to exceed 7000 lbs. 3.2 WB: / Short Wheel Base. ( Asset Coordinator Trucks) 1. SCOPE It is the intent of the JEA to purchase TWO (2) ONE Ton RAM DIESEL CREW CAB SRW 4X4 Pickup Trucks 6 6 BED with Various Configurations, Up-Fits and Options. All units

More information

POLAR ALUMINUM, ELLIPTICAL, TAPERED, BAFFLED, D.O.T. 406 TRAILER ATB

POLAR ALUMINUM, ELLIPTICAL, TAPERED, BAFFLED, D.O.T. 406 TRAILER ATB POLAR ALUMINUM, ELLIPTICAL, TAPERED, BAFFLED, D.O.T. 406 TRAILER ATB6 9500-5 15218-15221 2016 BARREL DESCRIPTION Model: ATB6 9500-5, aluminum, elliptical, tapered, baffled, DOT 406 trailer Code: DOT 406

More information

PLATFORM OPTIONS INDEX

PLATFORM OPTIONS INDEX EFFECTIVE: MARCH 8, 2017 Cargo/Load Management Options Exterior Options Reciever Hitch CL-V & ICC Bumper 14 Receiver Hitch CL-V Drawbars 14 Receiver Hitch CL-IV & ICC Drawbars 15 ICC Bumper 15 Tailskirt

More information

KNAPHEIDE PLATFORM BODIES

KNAPHEIDE PLATFORM BODIES KNAPHEIDE Knapheide has been designing and manufacturing platform bodies since the introduction of the Model T. Today, Knapheide continues to produce the highest quality platforms available. With selections

More information

RT-300-B. Tech Spec. Preliminary Information. * 30,000 pounds capacity at 10 ft. radius. * 4-wheel drive. * 4-wheel steer

RT-300-B. Tech Spec. Preliminary Information. * 30,000 pounds capacity at 10 ft. radius. * 4-wheel drive. * 4-wheel steer Tech Spec RT-300-B * 30,000 pounds capacity at 10 ft. radius * 4-wheel drive * 4-wheel steer * 360 degree continuous rotation * 60 ft. of full power main boom reach RT-300-2B CAPACITIES APPLY TO OPERATION

More information

TT-15 INSTALLATION INSTRUCTIONS SHOWN WITH OPTIONAL 2 PC. ALUMINUM PLATFORM AND LIGHT KIT

TT-15 INSTALLATION INSTRUCTIONS SHOWN WITH OPTIONAL 2 PC. ALUMINUM PLATFORM AND LIGHT KIT TM TOPLIFTER Tailgates By THIEMAN TT-15 INSTALLATION INSTRUCTIONS SHOWN WITH OPTIONAL 2 PC. ALUMINUM PLATFORM AND LIGHT KIT! IMPORTANT! KEEP IN VEHICLE! PLEASE READ AND UNDERSTAND THE CONTENTS OF THIS

More information

INVITATION TO BID ONE (1) 10-FOOT DUMPBODY DUMP TRUCK WITH DIESEL / CNG OPTIONS

INVITATION TO BID ONE (1) 10-FOOT DUMPBODY DUMP TRUCK WITH DIESEL / CNG OPTIONS P. O. B o x 1 5 4 0 T h o m a s v i l l e, G A 3 1 7 9 9 2 2 9-227- 7 0 0 0 F A X 2 2 9-227- 3 2 4 3 w w w. t h o m a s v i l l e. o r g INVITATION TO BID ONE (1) 10-FOOT DUMPBODY DUMP TRUCK WITH DIESEL

More information

Bolt on handle and mounting kit included in price. Bolt on handle and mounting kit included in price.

Bolt on handle and mounting kit included in price. Bolt on handle and mounting kit included in price. Extruded Plain Extruded aluminum provides strength, yet weighs less than other models with the same solid construction and protection. Extruded plain model is a great economical cab protector, while still

More information

-1- SPECIFICATIONS PERMANENTLY MOUNTED CONE SETTER PLATFORM ATTACHMENT INDEX

-1- SPECIFICATIONS PERMANENTLY MOUNTED CONE SETTER PLATFORM ATTACHMENT INDEX -1-002086 PERMANENTLY MOUNTED CONE SETTER PLATFORM ATTACHMENT INDEX I. GENERAL EQUIPMENT : A. Intent Statement B. Cone Setter Platform II. III. 1. General Specifications 2. Mounting Components 3. Close

More information

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS TECHNICAL SPECIFICATIONS GENERAL PURPOSE: The purpose of these specifications is to describe for purchase, a 2018 or newer 10-14 passenger airport shuttle bus with rear mounted handicap lift. This bus

More information

Tube Fired Hot Tack Distributors

Tube Fired Hot Tack Distributors www. Tube Fired Hot Tack Distributors 600 & 1,000 Gallon Capacity LD600T Marathon pumping distributors will save time on road maintenance, road construction, airport work, parking lots or wherever hot

More information

AUXILIARY BATTERY BOX INSTALLATION INSTRUCTIONS

AUXILIARY BATTERY BOX INSTALLATION INSTRUCTIONS AUXILIARY BATTERY BOX INSTALLATION INSTRUCTIONS The original TOMMY GATE hydraulic lift Assembling the Auxiliary Battery Box 1. Remove the cover from the auxiliary battery box by removing the two nuts and

More information

B-1125 DANKO STOCK. DANKO XL SKID UNIT UPF Defender Poly Tank

B-1125 DANKO STOCK. DANKO XL SKID UNIT UPF Defender Poly Tank FIRE PUMP DANKO XL SKID UNIT UPF Defender Poly Tank A Waterous 2515LE pump shall be provided and bolted directly to the specified engine and capable of the following performance: Max Pressure - 75 GPM

More information

VACUUM TANK LINE PAGE 1 VACUUM TANK LINE AmthorInternational.com

VACUUM TANK LINE PAGE 1 VACUUM TANK LINE AmthorInternational.com VACUUM TANK LINE PAGE 1 VACUUM TANK LINE 434.656.6233 AmthorInternational.com PAGE 2 TABLE VACUUM OF CONTENTS TANK LINE TABLE OF CONTENTS Page 3 Introduction Page 4 Code Vacuum Tanks Page 6 Non-Code Vacuum

More information

COMMONWEALTH OF PENNSYLVANIA DEPARTMENT OF CONSERVATION & NATURAL RESOURCES BUREAU OF FORESTRY DIVISION OF FOREST FIRE PROTECTION

COMMONWEALTH OF PENNSYLVANIA DEPARTMENT OF CONSERVATION & NATURAL RESOURCES BUREAU OF FORESTRY DIVISION OF FOREST FIRE PROTECTION COMMONWEALTH OF PENNSYLVANIA DEPARTMENT OF CONSERVATION & NATURAL RESOURCES BUREAU OF FORESTRY DIVISION OF FOREST FIRE PROTECTION Specifications for 500-Gallon Wildland Fire Flatbed Unit *Unless indicated

More information

RAMPMASTER SPECIFICATIONS

RAMPMASTER SPECIFICATIONS RAMPMASTER SPECIFICATIONS RAMPMASTER 15,000 GALLON WD STANDARD SPECIFICATION POWER MODULE ENGINE: ENGINE EQUIPMENT: COOLING: AIR INTAKE: EXHAUST: TRANSMISSION: REAR/DRIVE AXLE: FRONT AXLE: AIR BRAKE SYSTEM:

More information

SECTION FIRST RESPONDER SERIES HEAVY DUTY PERSONNEL LOCKERS DEBOURGH MFG. CO. 10/15/2013

SECTION FIRST RESPONDER SERIES HEAVY DUTY PERSONNEL LOCKERS DEBOURGH MFG. CO. 10/15/2013 SECTION 10501 FIRST RESPONDER SERIES HEAVY DUTY PERSONNEL LOCKERS DEBOURGH MFG. CO. 10/15/2013 PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General

More information

TROXELL COMPANY, INC E. HWY. 114 RHOME, TEXAS 76078

TROXELL COMPANY, INC E. HWY. 114 RHOME, TEXAS 76078 GENERAL CONSTRUCTION TROXELL COMPANY, INC. Specification Sheet 9250GL (220bbl) DOT407, Aluminum, Double Conical, Single Compartment, Tandem Axle Crude, Oil Tank Trailer MODEL: TRX407AL-220-1-DC-2-P NV-1407

More information

Pennsylvania State Police Tactical Mounted Unit. 25,500# GVWR Crew Cab Tractor

Pennsylvania State Police Tactical Mounted Unit. 25,500# GVWR Crew Cab Tractor Pennsylvania State Police Tactical Mounted Unit 25,500# GVWR Crew Cab Tractor The following pages specify the design and component requirements for a crew cab truck tractor. In addition to the vehicle

More information

SPECIFICATIONS FOR ONE CARB CERTIFIED CNG POWERED 13,000 GVWR CAB & CHASSIS SERVICE TRUCK WITH UTILITY BODY GENERAL CONDITIONS

SPECIFICATIONS FOR ONE CARB CERTIFIED CNG POWERED 13,000 GVWR CAB & CHASSIS SERVICE TRUCK WITH UTILITY BODY GENERAL CONDITIONS SPECIFICATIONS FOR ONE CARB CERTIFIED CNG POWERED 13,000 GVWR CAB & CHASSIS SERVICE TRUCK WITH UTILITY BODY GENERAL CONDITIONS The intent of this specification is to describe one minimum 13,000 lb GVWR

More information

Darley UHP-HV Diesel Specification 1

Darley UHP-HV Diesel Specification 1 Darley UHP-HV Diesel Specification 1 This dual pump is designed for either a powerhead type unit or a full module. The module provides a self-contained diesel powered slide-in type ultra high pressure

More information

BID FOR ONE (1) 1 TON CREW CAB TRUCK WITH SERVICE BODY OPENING APRIL 11, 2019 AT 10:00 A.M.

BID FOR ONE (1) 1 TON CREW CAB TRUCK WITH SERVICE BODY OPENING APRIL 11, 2019 AT 10:00 A.M. P. O. B o x 1 5 4 0 T h o m a s v i l l e, G A 3 1 7 9 9 2 2 9-2 2 7-7 0 0 0 F A X 2 2 9-2 2 7-3 2 4 3 w w w. t h o m a s v i l l e. o r g BID FOR ONE (1) 1 TON CREW CAB TRUCK WITH SERVICE BODY OPENING

More information

IC-200-G. Tech Spec. Industrial Crane. 15-Ton Max. Capacity Under 8 Feet Wide. Manufacturing Corp. Rated Capacity Limiter...

IC-200-G. Tech Spec. Industrial Crane. 15-Ton Max. Capacity Under 8 Feet Wide. Manufacturing Corp. Rated Capacity Limiter... Tech Spec IC-2-G Industrial Crane -Ton Under 8 Feet Wide Rated Capacity Limiter... Standard Capacity on Outriggers... 3, lbs Pick and Carry Capacity... up to 17, lbs Height... 7 11 Width... 7 1-1/2 Boom

More information

KNAPHEIDE PLATFORM BODIES

KNAPHEIDE PLATFORM BODIES www.knapheide.com KNAPHEIDE PLATFORM BODIES Knapheide has been designing and manufacturing Platform Bodies since the introduction of the Model T. Today, Knapheide continues to produce the highest quality

More information

SPECIFICATION, JEA CLASS 117: HALF TON 4X4 SWB (6 6 Bed) PICKUP TRUCK Crew Cab & Standard Cab Units UPDATED JULY 27, 2018

SPECIFICATION, JEA CLASS 117: HALF TON 4X4 SWB (6 6 Bed) PICKUP TRUCK Crew Cab & Standard Cab Units UPDATED JULY 27, 2018 1. SCOPE It is the intent of the JEA to purchase TWENTY SEVEN (27) HALF Ton 4X4 SWB (6 6 Bed / ALL UNITS) Pickup Trucks with Various Configurations, Up-Fits and Options. [19 Crew Cab and 9 Standard Cab].

More information

Albemarle County Virginia Brush Fire Truck Specification

Albemarle County Virginia Brush Fire Truck Specification Albemarle County Virginia Brush Fire Truck Specification Purpose: This specification is intended to be used for the procurement of Brush Fire Suppression Apparatus for the Fire Departments & Companies

More information

VACUUM TANK LINE PAGE 1 VACUUM TANK LINE AmthorInternational.com

VACUUM TANK LINE PAGE 1 VACUUM TANK LINE AmthorInternational.com VACUUM TANK LINE PAGE 1 VACUUM TANK LINE 434.656.6233 AmthorInternational.com PAGE 2 TABLE VACUUM OF CONTENTS TANK LINE TABLE OF CONTENTS Page 3 Introduction Page 4 Code Vacuum Tanks Page 6 Non-Code Vacuum

More information

Cantilever Series Mounting Instructions Ram Promaster Extended Body (AH) Present

Cantilever Series Mounting Instructions Ram Promaster Extended Body (AH) Present Ram Promaster Extended Body (AH)- 2014-Present Preparing the Gate 1. Remove the platform, mounting kit, and bridge assemblies, which are banded to the main assembly. Leave the banding that holds the folding

More information

Remount Proposal. Everest Emergency Vehicles 1133 Rankin Street St Paul, MN Eric Olson

Remount Proposal. Everest Emergency Vehicles 1133 Rankin Street St Paul, MN Eric Olson Remount Proposal Customer Dealer Everest Emergency Vehicles 1133 Rankin Street St Paul, MN 55116 651-236-8943 Eric Olson Module: INFORMATION 0.1.60 ****** Ambulance Re-chassis / Refurbish ****** * * Old

More information

NOTICE OF BID. The City of Pigeon Forge is receiving bids on five trucks for the Public Works Department.

NOTICE OF BID. The City of Pigeon Forge is receiving bids on five trucks for the Public Works Department. NOTICE OF BID The City of Pigeon Forge is receiving bids on five trucks for the Public Works Department. Specifications may be obtained from the Public Works Department in City Hall between the hours of

More information

this equipment. Does Not

this equipment. Does Not SPECIFICATIONS FOR THE SUPER SEALCOATER 550 TRAILER MOUNTED SEALCOAT APPLICATOR 420 N. Roosevelt Ave. Chandler AZ 85226 +1 800 528 8242 +1 602 276 0406 FAX +1 480 961 0513 www.crafco.com MARCH 2014 The

More information

FLORIDA SHERIFFS ASSOCIATION, FLORIDA FIRE CHIEFS ASSOCIATION, & FLORIDA ASSOCIATION OF COUNTIES

FLORIDA SHERIFFS ASSOCIATION, FLORIDA FIRE CHIEFS ASSOCIATION, & FLORIDA ASSOCIATION OF COUNTIES FLORIDA SHERIFFS ASSOCIATION, FLORIDA FIRE CHIEFS ASSOCIATION, & FLORIDA ASSOCIATION OF COUNTIES SPECIFICATION #23 TRACTOR-DRAWN AERIAL APPARATUS ALL ITEMS FACTORY INSTALLED UNLESS OTHERWISE INDICATED

More information

Chevrolet 1500HD 135. Chevrolet 2500HD 135. Ford E150SD 138. Ford E250SD 138

Chevrolet 1500HD 135. Chevrolet 2500HD 135. Ford E150SD 138. Ford E250SD 138 The following specifications are provided in order to describe and specify the design, construction, materials and equipment utilized and installed in the fabrication of a Swab Model ARF-6V Modular Fiberglass

More information

Cantilever Series Mounting Instructions Chevy Express (AD) present

Cantilever Series Mounting Instructions Chevy Express (AD) present Chevy Express (AD)- 2003-present Preparing the Gate 1. Remove the platform, mounting kit, and bridge assemblies, which are banded to the main assembly. Leave the banding that holds the folding cylinder

More information

IC-200-F. Tech Spec. Unmatched in Features and Performance

IC-200-F. Tech Spec. Unmatched in Features and Performance Tech Spec IC-2-F Unmatched in Features and Performance * Rated Capacity Limiter...Standard * Capacity on outriggers..., lbs. * Pick and carry capacity... up to 17, lbs. * Height...7 11-1/2 * Width...8

More information

Heavy-Duty Truck Bodies and Truck Tool Boxes for Tree Care Professionals

Heavy-Duty Truck Bodies and Truck Tool Boxes for Tree Care Professionals Heavy-Duty Truck Bodies and Truck Tool Boxes for Tree Care Professionals THE FIRST CHOICE IN: Chip Bodies Removable Roof Chip Bodies Truck Tool Boxes A CUT ABOVE THE REST About ARBORTECH Established in

More information

TENDER 2018 OR 2019, ONE AND A HALF TON CAB/CHASSIS, 4X4, DUMP BODY TRUCK

TENDER 2018 OR 2019, ONE AND A HALF TON CAB/CHASSIS, 4X4, DUMP BODY TRUCK Municipality of the County of Colchester Public Works Department 1 Church Street, Truro, NS B2N 3Z5 Telephone: (902) 897-3175 TENDER 2018 OR 2019, ONE AND A HALF TON CAB/CHASSIS, 4X4, DUMP BODY TRUCK Sealed

More information

Mantis Rerailer General Specifications

Mantis Rerailer General Specifications 2008 General Specifications 1. Typical Operating Parameters 2. General 1.1 Operating temperatures will typically be between 20 F (7 C) to 110 F (43 C). 1.2 Relative humidity ranges between 20% and 100%.

More information