Two Piece Propeller Shaft Replacement
|
|
- Randell Manning
- 5 years ago
- Views:
Transcription
1 2003 Chevrolet C Silverado 2WD [1GCGC13U93F206011] Sierra, Silverado VIN C/K Service Manual Driveline/Axle Propeller Shaft Repair Instructions Document ID: Two Piece Propeller Shaft Replacement Tools Required J Clamp Pliers Narrow Jaw Removal Procedure Important: Observe and accurately reference mark all driveline components relative to the propeller shaft and axles before disassembly. These components include the propeller shafts, the drive axles, the pinion flanges, the output shafts, etc. All components must be reassembled in the exact relationship to each other as they were when removed. In addition, published specifications and torque values, as well as any measurements made prior to disassembly must be followed. 1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. 2. Reference mark the propeller shaft (1), the universal joint strap (2), the universal bearing cap (4), the drive pinion yoke (5), and the rear axle housing (6) General Motors. All rights reserved.
2 Important: DO NOT re use the universal straps. Discard and replace with NEW. 3. Remove the rear propeller shaft bolts (3) and the universal joint strap (2). 4. Using a flat bladed tool, remove the clamp (2) securing the boot (3) to the front propeller slip yoke (4) and at the center bearing (1) by prying up the exposed end of the clamp (2). Notice: When removing the propeller shaft, do not attempt to remove the shaft by pounding on the yoke ears or using a tool between the yoke and the universal joint. If the propeller shaft is removed by using such means, the injection joints may fracture and lead to premature failure of the joint. 5. Remove the rear propeller shaft from the rear axle and the center support bearing.
3 Important: Step 6 is for those vehicles that have a slip yoke from the transmission from transfer case to the propeller shaft. 6. Reference mark the transmission or the transfer case (1), propeller shaft slip yoke (2), universal bearing cap (3), and the propeller shaft (4).
4 Important: Step 7 is for those vehicles that have the yoke attached to the output shaft. 7. Reference mark the transmission or transfer case (1), output shaft flange (2), universal joint bearing cap (3), and the propeller shaft.
5 8. Remove the center bearing support nuts (1). 9. Remove the center bearing support (2). Important: For those vehicles equipped with the yoke attached to the output shaft, proceed to step 10. Those vehicles equipped with a slip yoke, proceed to step For vehicles equipped with the yoke attached to the output shaft, use a suitable jack stand support the propeller shaft until propeller shaft is to be removed. 11. Remove the propeller shaft bolts (3), the straps (4), and the propeller shaft (2) from the transmission or the transfer case (1).
6 12. Remove the propeller shaft from the transmission or the transfer case. Installation Procedure Important: If servicing a propeller shaft with a slip yoke, proceed to step 1. If servicing a propeller shaft with the yoke attached to the output shaft of the transmission or the transfer case, proceed to step 3.
7 1. Align the reference marks on the transmission or the transfer case (1), slip yoke (2), universal bearing cap (3), and the propeller shaft. 2. Install the propeller shaft.
8 3. Align the reference marks on the transmission or the transfer case (1), output shaft yoke (2), and the propeller shaft (6). Important: When installing the propeller shaft bolts, hand tighten the bolts. DO NOT tighten them to specification until the center bearing support bolts have been installed and torqued to specifications.
9 4. Install the propeller shaft (2), the NEW straps (3), the propeller shaft bolts (3) on the transmission or the transfer case (1). 5. Position the center support bearing (1) on the frame. Notice: Refer to Fastener Notice. 6. Install the center bearing support nuts. Tighten Tighten the center support bearing nuts to 40 Y (30 lb ft).
10 7. Tighten the propeller shaft bolts (3) to specifications. Tighten Tighten the propeller shaft bolts to 25 Y (18 lb ft).
11 8. Install the boot (3) and the new clamps (2) onto the front propeller shaft slip yoke (4). Important: Ensure that the master splines on the slip yoke and the stub shaft are aligned before installing the rear propeller shaft. 9. Apply a small amount of clean chassis grease to the slip yoke and the rear propeller shaft. 10. Install the rear portion of the propeller into the front portion of the propeller shaft. 11. Align the reference marks on the rear axle housing (6), pinion yoke (5), universal bearing cap (4), and the rear propeller shaft (1). 12. Install the straps (2) and the bolts (3). Tighten Tighten the yoke retainer bolts to 25 Y (18 lb ft).
12 13. Using the J 43218, crimp the boot clamps until the dimensions shown are obtained. 14. Remove the support and lower that vehicle.
Locking Differential Adjustment (8.6 Inch Axle)
Page 1 of 9 2003 Chevrolet Chevy K Silverado - 4WD Sierra, Silverado (VIN C/K) Service Manual Driveline/Axle Rear Drive Axle - Locking/Limited Slip Rear Axle Repair Instructions Document ID: 890757 Locking
More informationTrailer Hitch Platform Package Installation
Page 1 of 9 2014 Chevrolet Silverado 1500-2WD Sierra, Silverado VIN C/K Accessory Installation Manual Accessories Trailer Hitch Platform Package Installation Table 1: Light Duty Hitch Platform Kit Contents
More informationUNIVERSAL JOINTS AND PROPELLER SHAFT
Section XII UNIVERSAL JOINTS AND SERVICE BULLETIN REFERENCE NUMBER DATE SUBJECT CHANGES UNIV JOINTS AND 537 UNIVERSAL JOINTS AND DATA AND SPECIFICATIONS Propeller Shaft Number used C-67 C-68 C-69 C-70
More informationDistributor Replacement
Page 1 of 11 2002 Chevrolet Chevy K Silverado - 4WD Sierra, Silverado (VIN C/K) Service Manual Document ID: 690165 Distributor Replacement Removal Procedure Notice: There are two procedures available to
More information2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES
2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential
More informationFront Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014. Axle
204-01 Front Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014 Axle 1 N620604 Axle pivot nut 2 N806859 Axle pivot bolt 3 3007 LH/ 3006 RH LH/ 3006 RH Axle Removal NOTICE:
More information2007 Hummer H Driveline/Axle Propeller Shaft - H3. Fastener Tightening Specifications Specification Application
2007 Driveline/Axle Propeller Shaft - H3 SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Bolt - Front Propeller Shaft CV Joint
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 6525 REAR AXLE FLIP & HANGER KIT 5 OR 6 INCH LOWERING 14&UP CHEVROLET SILVERADO / GMC SIERRA 1500 Thank you for being selective enough to choose our high quality BELLTECH PRODUCT.
More information2005 Mustang Workshop Manual
SECTION 205-00: Driveline System General Information 2005 Mustang Workshop Manual GENERAL PROCEDURES Procedure revision date: 07/29/2004 Driveline Angle Inspection Printable View (122 KB) Special Tool(s)
More informationPROPELLER SHAFT / / PROPELLER SHAFT GENERAL OVERVIEW AND OPERATION PROCESS 1. SPECIFICATION...
3310-01/3310-00/3310-06 GENERAL 1. SPECIFICATION... 3 OVERVIEW AND OPERATION PROCESS 1. OVERVIEW... 2. COMPONENT LOCATOR... 3310-01 FRONT... 3310-06 REAR... 3310-00 DISASSEMBLY AND REASSEMBLY PROPELLER
More informationSINGLE SPEED BEVEL GEAR TRANSMISSION
4. Remove one of the mounting screws for the belt guide and loosen the other. DO NOT bend the belt guide (Fig. 059). 22 TORO & LWN-BOY RER WHEEL DRIVE MODELS Transmission Removal and Belt Replacement On
More informationHP10251 KIT. Chevrolet Silverado WD / 4WD * GMC Sierra WD / 4WD * 1.5" / 2.25" Leveling Kit L6401_REV3_ECN1-1963
HP10251 KIT Chevrolet Silverado 1500 2WD / 4WD * GMC Sierra 1500 2WD / 4WD * 1.5" / 2.25" Leveling Kit *See PacPro Application Guide for proper fitment _REV3_ECN1-1963 KIT CONTENT A B C KIT CONTENTS A
More information2001 Chevrolet CORVETTE
riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly
More information2007 Hummer H Driveline/Axle Wheel Drive Shafts - H3. Fastener Tightening Specifications Specification Application
2007 Driveline/Axle Wheel Drive Shafts - H3 SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Front Wheel Drive Shaft Nut 260
More informationDistributor Replacement (HVS)
1 of 8 3/3/2018, 3:02 PM 1998 Chevrolet K Pickup - 4WD Chevy Pickup, GMC Pickup, Suburban, Tahoe, Yukon VIN C/K Service Manual Engine Engine Electrical Repair Instructions Document ID: 207477 Distributor
More informationINSTALLATION INSTRUCTION 88146
INSTALLATION INSTRUCTION 88146 Rev H FOR RANCHO SUSPENSION SYSTEM RS6547: 4WD SUBURBAN/YUKON XL, 4WD TAHOE/YUKON, & 4WD AVALANCHE READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING
More informationDriveline Service & Maintenance
Section 3-3 Driveline Inspection Driveline Service & Maintenance To prevent serious eye injury, always wear eye protection gear when you perform vehicle maintenance or service. Do not service a drivehsaft
More informationPage 1 of 5 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/19/2000 Spindle, RH and LH Shaft and Joint
More informationFRONT SEAT TRACK MOTOR. Removal
1 of 19 FRONT SEAT TRACK MOTOR Removal WARNING: - Always wear safety glasses when repairing a supplemental restraint system (SRS) vehicle and when handling an air bag module. This will reduce the risk
More informationDistributor Replacement (5.7L)
Page 1 of 13 1999 Chevrolet Chevy K Pickup - 4WD Escalade, Pickup (Classic), Suburban, Tahoe, Yukon (VIN C/K) Service Manual Engine Engine Mechanical - 5.0L and 5.7L Repair Instructions Document ID: 371340
More informationATTENTION ADVANCE SERVICE BULLETIN INFORMATION
SUBJECT: NO: 21-10-98 Loss Of Fifth Gear GROUP: Transmission EFFECTIVE DATE: Sep. 11, 1998 CHRYSLER MAIL MANAGEMENT SYSTEM DATE: AUG. 28, 1998 ATTENTION ADVANCE SERVICE BULLETIN INFORMATION The following
More information4. Control Valve (Power Steering Gearbox)
4-3 [W4A0] SERVICE PROCEDURE A: CHECKING OIL LEAKING POINTS S4M0153A (1) Power cylinder (2) Cylinder (3) Rack piston (4) Rack axle (5) Input shaft (6) Valve housing 1. OIL LEAKING POINTS 1) If leak point
More informationSTEERING COLUMN, LOWER STEERING SHAFT, AND STEERING GEAR BOX ALIGNMENT
Please note: this is a draft document it has not been validated. If you choose to use it please check all steps and, if you find something wrong or have suggestions, contact Rob Mueller. This was presented
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION CENTER BEARING SUPPORT ASSEMBLY Removal 1. With transmission in neutral and parking brake off, raise vehicle. Scribe alignment marks on all flange/yokes and slip joints to be disassembled
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 6522 REAR AXLE FLIP & SHACKLE KIT 07-UP CHEVROLET 1500 REGULAR CAB ONLY
More informationOverhaul Special Tools Required
1 of 31 Overhaul - Special Tools Required - Cylinder end seal remover attachment, 07NAD-SR3020A - Pilot collar, 07GAF-PH70100 - Valve seal ring sizing tool, 07NAG-SR3090A - Ball joint boot clip guide,
More informationDriveshaft Components
Demand the original. Driveshaft Components www.demandaam.com Demand the original. Demand the original. Only original equipment components are guaranteed to meet the same specifications as the parts they
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FOR A136 REAR DRUM TO DISC BRAKE CONVERSION KIT for 1970-75 Jeep, CJ SERIES with Dana 44 flanged axle Thank you for choosing STAINLESS STEEL BRAKES CORPORATION
More informationThe numbers below refer to the step numbers on the diagnostic table.
xtooltipelement Service Information 2004 Chevrolet C Silverado - 2WD Sierra, Silverado VIN C/K Service Manual Body Wipers/Washer Systems Diagnostic Information and Procedures Document ID: 815265 Wipers
More informationPROPELLER SHAFT PR 1
PR1 PR2 PREPARATION PREPARATION SST (SPECIAL SERVICE TOOLS) 0932520010 Transmission Oil Plug 2JZGE M/T 0932540010 Transmission Oil Plug 2JZGE A/T 0933000021 Companion Flange Holding Tool 0933050010 Propeller
More informationMAINTENANCE MANUAL. Drivelines MM Edition october/11
MAINTENANCE MANUAL Drivelines MM-96147 Edition october/11 Index 1 - Drivelines... 03 2 - Introduction... 05 3 - Inspection... 06 4 - RPL Series PermalubeTM... 12 5 - Full-Round... 23 6 - Wing-Style PermalubeTM...
More informationAssist Step Kit Installation (Side Assist Step)
Page 1 of 6 2015 Chevrolet Silverado - 2WD Cheyenne, Sierra, Silverado Accessory Installation Manual Accessories Exterior Trim Accessories Accessories Document ID: 2741491 Assist Step Kit Installation
More informationDRIVE AXLE - 4WD MODELS WITH INTEGRAL HOUSING
DRIVE AXLE - 4WD MODELS WITH INTEGRAL HOUSING 1988 Toyota Celica DRIVE AXLES Toyota Integral Housing Celica (Rear) DESCRIPTION housing. Drive axle assembly is hypoid type with integral carrier AXLE RATIO
More informationPROPELLER SHAFT & DIFFERENTIAL CARRIER SECTIONPD CONTENTS
PROPELLER SHAFT & DIFFERENTIAL CARRIER SECTIONPD CONTENTS PREPARATION...2 PROPELLER SHAFT...5 On-Vehicle Service...6 Removal and Installation...7 Inspection...7 Disassembly...7 Assembly...8 ON-VEHICLE
More informationTransmission Diesel Engines
Page 1 of 17 SECTION 307-01B: Automatic Transaxle/Transmission TorqShift 6 2011 F-250, 350, 450, 550 Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 11/12/2010 Transmission
More informationADVANCE ADAPTERS INC. Fixed Yoke kit (S.Y.E. Kit)
ADVANCE ADAPTERS INC. Fixed Yoke kit (S.Y.E. Kit) Instruction Sheet P/N: 50-7905 & 50-7906 KIT CONSISTS OF: No. Qty Part No. Description 1. 1 51-7906 TAILHOUSING, DIECAST 2. 1 52-7905 SHAFT, MAIN OUTPUT
More informationDocument ID: This PI was superseded to change labor operation time from.4 to.5. Please discard PIP4307G.
Page 1 of 5 2006 GMC Truck GMC K Sierra - 4WD Sierra, Silverado (VIN C/K) Service Manual Driveline/Axle Rear Drive Axle #PIP4307H: MAP sensor Icing Or P0106 - keywords 6.6 6.6L absolute air DTC engine
More informationSpicer Driveshafts. Service Manual. DSSM3264 September 2007
Spicer Driveshafts Service Manual DSSM3264 September 2007 Table of Contents Safety...................... 1 General Safety.......................... 1 Component Safety...................... 2 Driveline...........................
More informationADVANCE ADAPTERS INC. P/N: NP231 SHORT SHAFT "FIXED YOKE" KIT
Paso Robles, CA 93447 PAGE 1 OF 10 Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 06-24-02 KIT CONSISTS OF: No. Qty Part No. Description 1. 1 51-7906 TAILHOUSING, DIECAST 2. 1 52-7905 SHAFT,
More information2004 DRIVELINE/AXLE. Rear Drive Axle - Corvette. Fastener Tightening Specifications Specification Application
2004 DRIVELINE/AXLE Rear Drive Axle - Corvette SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Differential Case Bolts 55 N.m
More informationExhaust System Installation for Chevrolet Silverado and GMC Sierra PN , , , , ,
Exhaust System Installation for Chevrolet Silverado and GMC Sierra PN-140535, 140536, 140537, 140538, 140539, 140540 ***** Please compare the parts in the box with the bill of materials provided *****
More informationONLY AFTER ALL MEASUREMENTS HAVE BEEN TAKEN. Remove any components in the chassis that may interfere with the retarder and/or mounting hardware.
Tools Needed Transmission jack Hand held calculator Mechanics hand tools Torque wrench (up to 250 lb.-ft) ½ heavy duty drill or frame drill Tape measure Straight edge Electronic Angle meter (Spicer Anglemaster
More informationSteering Gearbox Disassembly
Steering Gearbox Disassembly Steering Rack Disassembly 5. Unbend the lock washer. Before disassembling the gearbox, wash it off with solvent and a brush. Do not dip seals and O-rings in solvent. 1. Remove
More informationTOYOTA COROLLA LOWERING SPRINGS Preparation
Preparation Part Number: PTR07-02140 Kit Contents Item # Quantity Reqd. Description 1 2 Front Spring 2 2 Rear Spring 3 1 Hardware 4 1 Instruction Form Hardware Bag Contents Item # Quantity Reqd. Description
More information2012 Expedition, Navigator Workshop Manual
Item Part Number Description 1 W720586 Differential housing cover bolt (12 required) 2 4033 Differential housing cover 3 Differential bearing cap bolts (part of 4010) (4 required) 4 Differential bearing
More information1 M-3000-H4 F150 4X4 Lowering Kit
READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.
More informationTECHNICAL BULLETIN. Yoke Removal and Installation Procedure for Meritor Drive Axles. Remove the Yoke and Pinion Seal WARNING CAUTION CAUTION.
Issued 11-99 TECHNICAL BULLETIN Yoke Removal and Installation Procedure for Meritor Drive Axles Remove the Yoke and Pinion Seal Figure 1 WARNING Park the vehicle on a level surface. Block the wheels to
More informationHalfshaft. Special Tool(s) Differential Plug (T89P-4850-B) Differential Seal Protector Halfshaft Removal Tool
Halfshaft Special Tool(s) Differential Plug 205-294 (T89P-4850-B) Differential Seal Protector 205-461 Halfshaft Removal Tool 205-475 Hub Remover/Replacer 204-069 (T81P-1104-C) Metric Hub Remover Adapter
More informationInstallation Instructions for the Tera low range Dana 20 (LOW20)
Installation Instructions for the Tera low range Dana 20 (LOW20) Tera Manufacturing, Inc. 5251 South Commerce Dr. Murray, Utah 84107 Phone/801.288.2585 Fax/801.288.2571 www.teraflex.biz Attention: Verify
More informationInstallation Instructions Truckin Suspension Lift Kit 1999-Newer DODGE DAKOTA-DURANGO (Rack and Pinion)
Installation Instructions Truckin Suspension Lift Kit 1999-Newer DODGE DAKOTA-DURANGO (Rack and Pinion) Important! Read all instructions before attempting any work on the vehicle. DO NOT DISSASSEMBLE ANY
More informationThis bulletin is being revised to update the Warranty information. Please discard Corporate Bulletin Number (Section Suspension).
1 of 3 8/6/2011 9:07 PM 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer VIN S/T Service Manual Document ID: 2088947 Subject: Models: Rattle, Clunk, Pop, Snap Noise from Front and/or
More informationDRIVE SHAFT ALIGNMENT
DRIVE SHAFT ALIGNMENT 1988 Jeep Cherokee 1988 Drive Shafts Alignment DESCRIPTION Drive shafts are balanced, one-piece, tubular shafts with universal joints at each end. Number used in vehicle varies: one
More informationFuel System Diagnosis
Page 1 of 6 2004 Chevrolet Chevy K Silverado - 4WD Sierra, Silverado (VIN C/K) Service Manual Engine Engine Controls - 6.6L (LLY) Diagnostic Information and Procedures Document ID: 1460257 Fuel System
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
ZJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 6 page REAR SUSPENSION... 14 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION
More informationDRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I
DRIVE AXLE 1990 Nissan 240SX 1990 DRIVE AXLES Rear Axle - R200 240SX, 300ZX DESCRIPTION & OPERATION The axle assembly is a hypoid type gear with integral carrier housing. The pinion bearing preload adjustment
More informationDRIVE SHAFT LOCATION INDEX
DRIVE SHAFT LOCATION INDEX 2005 DRIVELINE/AXLE Drive Shaft - MX-5 Miata Fig. 1: Identifying Drive Shaft Location DRIVE SHAFT PRE-INSPECTION 1. Inspect the dust boot on the drive shaft for cracks, damage,
More informationYukon Gear & Axle D30, D44 & GM 8.5" Hardcore Locking Hub Installation Guide
Yukon Gear & Axle D30, D44 & GM 8.5" Hardcore Locking Hub Installation Guide PLEASE READ COMPLETELY BEFORE INSTALLATION Application Guide: YHC70005 D30 & D44 30spl - YA WU-08 Spin Free - D30, 30 spline
More informationCondition/concern. Recommendations/Instructions
#PI1354C: Information on Vibration Analysis and Diagnostic - (Aug 14, 2015) Subject: Information on Vibration Analysis and Diagnostic 2014 Chevrolet Silverado 1500 2015 Chevrolet Silverado 1500 Models:
More informationIf it exceeds the maximum specification, replace the propeller shaft.
If it exceeds the maximum specification, replace the propeller shaft. Maximum runout o 0.4 mm {0.016 in} 2. Inspect the play and rotation of the joint by turning the universal joint in the directions shown
More informationA REPAIR KIT PART NUMBER IS AVAILABLE AND CONTAINS ALL THE PARTS NORMALLY REPLACED DURING A STANDARD MAINTENANCE REPAIR.
AZ Pump Instructions PUMP NOT RUNNING PROPERLY: Check to be sure air pressure is reaching the pump, check to be sure air filter is not clogged; clean or replace as required. Check to be sure fluid filter
More informationService Bulletin PRELIMINARY INFORMATION
Service Bulletin PRELIMINARY INFORMATION File in Section: - Bulletin No.: PI1376 Date: December, 2014 Subject: Front Seat Lateral Movement and/or Click Type Noise While Driving Models: 2015 Cadillac Escalade
More informationDRIVE AXLE - INTEGRAL HOUSING
DRIVE AXLE - INTEGRAL HOUSING 1993 Toyota Celica 1993 DRIVE AXLES Toyota Differentials & Axle Shafts - Integral Housing Toyota; Celica All-Trac DESCRIPTION Drive axle assembly is a hypoid type with integral
More information1999 Toyota RAV DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2. AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2
1999-2000 DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2 DESCRIPTION & OPERATION On RAV4 models, axle shafts transfer power from transaxle to front wheels (FWD), or front and rear wheels
More informationFRONT AXLE 26-1 CONTENTS GENERAL INFORMATION... 2 HUB AND KNUCKLE ASSEMBLY SERVICE SPECIFICATIONS... 4 DRIVE SHAFT LUBRICANTS...
26-1 FRONT AXLE CONTENTS GENERAL INFORMATION.................. 2 SERVICE SPECIFICATIONS................. 4 LUBRICANTS.............................. 4 SEALANTS AND ADHESIVES.............. 5 SPECIAL TOOLS...........................
More informationSUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
More informationTL REPAIR MANUAL. Telma model FV61-00 (FU831310) replacement on Dana 19060S axle. Page 1 of 8 30jun10
TL103035 REPAIR MANUAL Telma model FV61-00 (FU831310) replacement on Dana 19060S axle Page 1 of 8 30jun10 Exploded view TL103035 Stator carrier Telma Unit Flange Yoke Page 2 of 8 30jun10 Disassembly 1.
More informationSTaSIS Engineering B6 B7 Streetsport Suspension
STaSIS Engineering B6 B7 Streetsport Suspension SS Suspension Kit Parts List Qty Description Part Number 1 STaSIS adjusted Koni cadmium plated dampers (2 front, 2 rear) 1150-5061 Special Tools Required
More informationIT IS RECOMMENDED THAT SPECIAL TOOL OT38793 (ELECTRONIC VIBRATION ANALYZER) BE USED TO HELP PINPOINT THE ROOT CAUSE OF THE VIBRATION.
NUMBER: 03-02-99 GROUP: Axles And Propshafts DATE: Mar. 26, 1999 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
More informationPROPELLER SHAFT AND UNIVERSAL JOINTS
PROPELLER SHAFT AND UNIVERSAL JOINTS 16-1 GROUP 16 PROPELLER SHAFT AND UNIVERSAL JOINTS CONTENTS Page Page Ball and Trunnion Universal Joint. 4 Propeller Shaft (TY-1) 7 Center Bearing (TY-1) 8 Propeller
More informationPRELIMINARY INFORMATION
Service Bulletin File in Section: - Bulletin No.: PI1354A Date: December, 2014 PRELIMINARY INFORMATION Subject: Information on Vibration Analysis and Diagnostic Models: 2014 Chevrolet Silverado 1500 2015
More informationFRONT AXLE Click on the applicable bookmark to selected the required model year
FRONT AXLE 26-1 FRONT AXLE CONTENTS GENERAL INFORMATION.................. 2 SERVICE SPECIFICATIONS................. 4 LUBRICANTS.............................. 4 SEALANTS AND ADHESIVES.............. 5 SPECIAL
More informationSECTION Front Drive Axle/Differential
205-03-i Front Drive Axle/Differential 205-03-i SECTION 205-03 Front Drive Axle/Differential CONTENTS PAGE Axle... 205-03-2 205-03-2 Front Drive Axle/Differential 205-03-2 Axle Special Tool(s) C-Frame
More information2006 Dodge RAM of 10 11/15/ :03 PM REMOVAL. Subarticles. Submodel: SLT Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS
EAR-PINION/RING - REMOVAL AND INSTALLATION 1 of 10 11/15/2012 12:03 PM 2006 Dodge RAM 1500 Submodel: SLT Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Subarticles GEAR-PINION/RING - REMOVAL GEAR-PINION/RING
More informationSUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS
DN SUSPENSION 2-1 SUSPENSION TABLE OF CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION - 4x2... 6 page FRONT SUSPENSION - 4x4... 14 REAR SUSPENSION... 23 ALIGNMENT TABLE OF CONTENTS page AND OPERATION WHEEL
More informationPROPELLER SHAFTS 16-1 PROPELLER SHAFTS CONTENTS
Z PROPELLER SHAFTS 16-1 PROPELLER SHAFTS CONTENTS page GENERAL INFORMATION... 1 PROPELLER SHAFT REPLACEMENT... 7 SERVICE DIAGNOSIS/PROCEDURES... 3 page TORQUE SPECIFICATIONS... 14 UNIVERSAL JOINT REPLACEMENT...
More informationService Bulletin Trucks
Volvo Trucks rth America, Inc. Greensboro, NC USA This Service Bulletin replaces Service Bulletin 084 01, Special Tools, Group 4 (11.2003), Publication no. PV776 TSP 20 000363. Service Bulletin Trucks
More informationModel 4360 Teardown and Reassembly Instructions
Clean the outside surface of the transaxle. Place the shifter in neutral position. Remove detent cover screw (item 3), detent cover (item 4), detent springs (item 5), and detent balls (item 6). Use a magnet
More informationNP231 SHORT SHAFT "FIXED YOKE" KIT
Page 1 of 11 KIT CONSISTS OF: No. Qty Part No. Description 1. 1 51-7905 TAILHOUSING, DIECAST 2. 1 52-7905 SHAFT, MAIN OUTPUT 3. 1 300474 SEAL WASHER, REAR YOKE 4 1 300475 YOKE, C.V. REAR 5. 1 300476 NUT,
More informationShort-throw Shifter Installation Guide
Short-throw Shifter Installation Guide Removal Procedure 1) Remove the shift control knob. A. Lift up on the rear portion of the shift control closeout boot retaining ring and detach the retaining ring
More informationPR 3. PROPELLER SHAFT FRONT PROPELLER SHAFT ASSEMBLY (for 4WD) DISASSEMBLY
OPELLER SHAFT FRONT OPELLER SHAFT ASSEMBLY (for 4WD) 3 C029928 DISASSEMBLY 1. INSPECT FRONT OPELLER SHAFT ASSEMBLY (a) Check that the propeller shaft is not damaged or deformed. If necessary, replace the
More informationInstallation Guide for the Extreme Short Shaft Kit
INSTALLATION GUIDE Tera Manufacturing, Inc. 5251 South Commerce Dr. Murray, Utah 84107 Phone/801.288.2585 Fax/801.713.2313 www.teraflex.biz Installation Guide for the Extreme Short Shaft Kit Part #004444400
More informationINSTALLATION INSTRUCTION 88148
INSTALLATION INSTRUCTION 88148 Rev C For Rancho Suspension Systems RS6548, RS6549 & RS6550: GM 2500HD, 2500, and 1500HD Trucks READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION
More informationNP231 SHORT SHAFT "FIXED YOKE" KIT FOR NON-CV YOKES AND FLANGE YOKES
KIT CONSISTS OF: No. Qty Part No. Description 1. 1 51-7906 TAILHOUSING, DIECAST 2. 1 52-7905 SHAFT, MAIN OUTPUT 3. 1 300474 SEAL WASHER, REAR YOKE 4. 1 300476 NUT, REAR YOKE 5. 1 300480 SEAL WASHER, FRONT
More informationINSTALLATION INSTRUCTION 88051
INSTALLATION INSTRUCTION 88051 For Rancho Suspension System RS6551: Chevrolet 2500 Suburban & 2500 Avalanche READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT
More informationInstallation Instructions Truckin Suspension 6.5 Suspension Lift Kit DODGE DAKOTA-DURANGO (worm and sector)
Installation Instructions Truckin Suspension 6.5 Suspension Lift Kit 1997-1999 DODGE DAKOTA-DURANGO (worm and sector) Important! Read all instructions before attempting any work on the vehicle. DO NOT
More information1984 Dodge W250 PICKUP
1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
TJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 5 page REAR SUSPENSION... 12 ALIGNMENT INDEX page GENERAL INFORMATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION
More informationTRANSMISSION AND TRANSFER CASE
XJ TRANSMISSION AND TRANSFER CASE 21-1 TRANSMISSION AND TRANSFER CASE TABLE OF CONTENTS page AX5 MANUAL TRANSMISSION... 1 NV3550 MANUAL TRANSMISSION... 42 AUTOMATIC TRANSMISSION 30RH... 88 page AW 4 AUTOMATIC
More informationSUSPENSION 2-1 SUSPENSION CONTENTS
TJ SUSPENSION 2-1 SUSPENSION CONTENTS page ALIGNMENT... 1 FRONT SUSPENSION... 6 page REAR SUSPENSION... 13 ALIGNMENT INDEX page DESCRIPTION AND OPERATION WHEEL ALIGNMENT... 1 DIAGNOSIS AND TESTING SUSPENSION
More informationDirector P. O. Box 1904 Service Engineering Operations Dearborn, Michigan Ford Customer Service Division
Michael A. Berardi Ford Motor Company Director P. O. Box 1904 Service Engineering Operations Dearborn, Michigan 48121 Ford Customer Service Division TO: SUBJECT: All U.S. Ford and Lincoln Dealers August
More informationTransmission Overhaul Procedures-Bench Service
How to Install the Auxiliary Countershaft Assembly Special Instructions To make auxiliary section assembly easier, you can make an auxiliary section fixture out of a 2" x 12" piece of wood. 3' 1' 3" 4.56"
More informationPart # WD Jeep Wrangler TJ Stage I 3 to 4 Lift Now Manufactured With Chromolly Arms PRO COMP SUSPENSION. Suspension Systems that Work!
PRO COMP SUSPENSION Suspension Systems that Work! Part # 55495 97-2002 4WD Jeep Wrangler TJ Stage I 3 to 4 Lift Now Manufactured With Chromolly Arms This document contains very important information that
More informationSTEERING SYSTEM - MANUAL
Article Text ARTICLE BEGINNING 1991-92 STEERING Chrysler Motors/Mitsubishi - Manual Steering - Rack & Pinion Dodge; Colt, Colt Vista, Colt 200, Eagle; Summit Mitsubishi; Eclipse, Mirage, Precis DESCRIPTION
More information1989 Jeep Cherokee. STEERING COLUMN' '1989 STEERING Jeep Steering Columns STEERING COLUMN STEERING Jeep Steering Columns
STEERING COLUMN 1989 STEERING Jeep Steering Columns DESCRIPTION All models use collapsible steering columns. All columns have integral ignition switch and locking device. Optional tilt wheel is available
More informationTechnical Service BULLETIN
Technical Service BULLETIN September 16, 2002 Title: Models: 01 02 Sequoia BR005-02 BRAKES TSB REVISION NOTICE: March 5, 2004: A torque specification on page 9, step 24, was changed. September 8, 2003:
More informationC5 Corvette M/T Differential Strut Installation Instructions
1 P a g e 6930B Derek Dr. Fort Wayne, IN 46803 Phone: 260-245-0352 Fax: 260-245-0358 www.hoosierpe.com C5 Corvette M/T Differential Strut Installation Instructions Application: 1997-2004 C5 Corvette with
More informationRear Axle Single-Reduction Carrier
Revised 08-0 Rear Axle Single-Reduction Carrier Model MS-3 Maintenance Manual MM-030 Service Notes Service Notes Notes About This Manual This manual provides instructions for Meritor s model MS-3 single-reduction
More informationThis file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
More informationCOMPONENTS REAR DIFFERENTIAL COMPONENTS
COMPONENTS REAR DIFFERENTIAL COMPONENTS REMOVAL 1. Drain the differential gear oil. 2. Remove the rear disk brake. 3. Remove the parking brake and cable. 4. Remove the stabilizer bar. 5. Pull out the
More informationMANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2)
MANUAL TRANSMISSION 7B 1 RODEO TRANSMISSION MANUAL TRANSMISSION MUA 5C (4X2, 4X4) AND TREMEC T5R(4X2) CONTENTS Service Precaution...................... 7B 2 General Description..................... 7B
More information