BRAKE PADS REPLACEMENT
|
|
- Bennett Cross
- 5 years ago
- Views:
Transcription
1 KLR650 Homepage Contact Me You must remove the "REMOVE-THIS" in my address for it to work. This is a hobby website dedicated to the Kawasaki KLR650 motorcycle. I make no claim concerning the accuracy of the procedures, nor do I guarantee the success of any work done using them. All users of the material found here are advised that there is no real or implied warranty associated in any way with the website content, and that all content available here is for use at your own risk. Copyright 2001 Mark's KLR Pages All Rights Reserved No copying or other redistribution by any method will be permitted without my express written permission. Links Miscellaneous Info D.I.Y. Tips Grease 101 Technical Articles BRAKE PADS REPLACEMENT The wheel does not have to be removed from the bike to replace the pads on either the front or rear of the bike. This is a relatively easy job, but the brake pads on the rear, especially, can be a little annoying. FRONT Caliper A1 Brochure Conversions KLR650 FAQ Painting Plastic Forms Maintenance Log Shim Record Chart Pictures Corbin Saddle Procedures in PDF 12v Waterproof Outlet REAR Caliper
2 Acerbis Disk Installation Balancer Adjustment Brake Pads Cam Chain Timing Carb Air Mixture Carb Rain T-Mod Decalifornication Doohickey Upgrade Easy Lift Fork Oil Change Horn Upgrade Hydraulic Clutch JC Whitney Trunk Maier Woods Pro FRONT: Mirror Mount Repair Oil Screen Cleaning TIME-SERT Radiator Cooling Mod Ramp Loading Safety Switch Bypass Shark Fin Installation Shim Storage
3 Box Shim Value Table SuperBrace To start, this is not necessary, but you'll probably find it easier to replace the brake pads if the caliper is able to be moved freely about. If you choose to do this, you only have to remove the nut behind the reflector that holds the entire assembly to the tab on the fork tube - pointed to by the arrow in the above picture. Swingarm Maint Torque Values Tube Valve Tools Valve Adjustment Vista-Cruise Lock Water Pump Seals Wheel Alignment The caliper is held in place by two bolts, marked in the picture above by two red dots. Remove the bottom one, and then the top. Hold the caliper as you remove the top bolt so that it doesn't swing free.
4 The rear is shown in the photo above, but the idea is the same. It's my suggestion that you either hang the caliper by its frame in such a way that you can easily work on it, or that you have something like a 5 gallon pail available to lay the caliper on. Don't allow the caliper to just hang by the brake line, tie it up with rope or wire. On the front, I hung the caliper with a rope around it and the handlebars. Shown above is the start of the procedure. Note the "legs" of the hairpin sticking out at the top of the "U" just above the Galfer text. That isn't a bolt, but rather a pin with a bolt head. Turn the pin until the head of the hairpin is sticking out and available - (as in the last picture of this front procedure) - and remove it with needle nose pliers, or whatever works best for you.
5 Pull the pin, soldier! The picture above shows the pin being removed. When the pin has been removed, get a grip on the caliper mount and press the pads down to put the piston into a fully open position. This will take some effort, but not a tremendous amount. Carefully apply a very light, even coat of grease to the pin to ease reinstallation. The picture above shows the start of the pad removal. The piston is fully open, so the top pad can be swung out and removed from the mounting
6 post. NOTE: Look at the spring clip where the top pad rests, showed most clearly on the left side. Note that the ends are "L" shaped, the pad frame sits into the clip and into the "L" for correct operation. The bottom pad comes up and out with a gentle push from the bottom. The above picture shows the caliper with both pads removed. NOTE: I've found that for a few years now I've had to slightly enlarge the hole in the pads because I couldn't get the pin through otherwise. Your experience may be different...
7 The bottom pad fits easily into place, and should be done now. As shown above, I found it was easier to line up both pad frame holes by inserting the pin into the bottom pad, and then holding the pad securely in place with my thumb. Put the upper pad on the mounting post, remove the pin, and swing the upper pad into place. Make sure the upper pad frame is fitted correctly into the spring clip, resting in the "L" shaped arms. Insert the pin down through the hole in the caliper and the two holes in the pad frames. Insert the hairpin. The picture above shows the completed job. The piston will still be fully compressed, so it will be an easy job to slip the pads over the rotor. I'd suggest blue Loctite on the caliper mounting bolts. Torque them to: 25 N-m, 2.5 Kg-m, 18 ft-lb Remount the brake line holder if you removed it. I use a little blue Loctite on this, also. Just snug is correct. REAR:
8 To provide free movement of the caliper, I suggest removing this rear line holder, as shown above. Remove the two caliper mounting bolts, shown in the picture above, and marked with red dots. As with the front, remove the bottom bolt, and then hold the caliper as you remove the top bolt.
9 It's my suggestion that you either hang the caliper by its frame in such a way that you can easily work on it, or that you have something like a 5 gallon pail available to lay the caliper on, and work on it there. Don't allow the caliper to just hang by the brake line, tie it up with rope or wire. The above picture shows the caliper at the start of the replacement. As with the front, you'll want to compress the piston as fully as possible to
10 make the removal of the first pad - and later reinstallation of the pads over the rotor - easier. The bottom pad is removed first, as shown above. It comes up with a push from underneath without too much trouble if the piston is fully compressed, which gives it room to get past the mounting plate and upper pad frame.
11 With the bottom pad out, the next thing to do is remove the upper pad. Put your thumbs on the plate in the middle, marked with the RED line. Put your hands on and around the caliper body, and push the plate down, in the direction of the YELLOW arrow. You should now be able to slide the top pad up, and over the mounting posts. You may find it works best to get the pad off one post at a time using a slight rocking motion. If it doesn't come off, you need to compress that middle plate more.
12 Reinstallation is easier because everthing is already pretty much set the best way for it. Drop the lower pad into place, making sure you set it correctly into place. Install the upper pad. Try moving it onto the two mounting posts all at once, or over one post at a time, rocking it slightly into place.
13 The above picture shows the completed installation of the pads. Note that with the piston still compressed, there is ample room for the pads to easily fit over the rotor. Remount the caliper over the rotor, and torque the bolts to the appropriate value. (I'd suggest blue Loctite on the caliper mounting bolts.) Torque them to: 25 N-m, 2.5 Kg-m, 18 ft-lb I like a small amount of blue Loctite on the screw that holds the brake line bracket in place. Just snug is correct.
This is a hobby website dedicated to the Kawasaki KLR650 motorcycle. I make no claim concerning the
KLR650 Homepage Contact Me You must remove the "REMOVE-THIS" in my email address for it to work. This is a hobby website dedicated to the Kawasaki KLR650 motorcycle. I make no claim concerning the accuracy
More informationThis is a hobby website dedicated to the Kawasaki KLR650 motorcycle. I make no claim concerning the
KLR650 Homepage Contact Me You must remove the "REMOVE-THIS" in my email address for it to work. This is a hobby website dedicated to the Kawasaki KLR650 motorcycle. I make no claim concerning the accuracy
More informationThis is a hobby website dedicated to the Kawasaki KLR650 motorcycle. I make no claim concerning the
KLR650 Homepage Contact Me You must remove the "REMOVE-THIS" in my email address for it to work. This is a hobby website dedicated to the Kawasaki KLR650 motorcycle. I make no claim concerning the accuracy
More informationInstalling the Audiovox CCS-100 Cruise Control.
Installing the Audiovox CCS-100 Cruise Control. This article was written by: Lon Lawrence w650kawasaki@leaco.net Cruise Control : Audiovox CCS-100 ($89) Webpage : www.summitracing.com Message: I've installed
More informationThanks for Ordering The Kawasaki KLX Adjustable Lowering Kit From
www.scootworks.com Thanks for Ordering The Kawasaki KLX Adjustable Lowering Kit From READ THIS BEFORE UNPACKING YOUR KIT! This instruction booklet contains detailed steps for installing the rear suspension
More informationPrerequisites: Shop Manual (recommended) pages 3-9 through 3-13.
Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961
More informationDIY: Shiver Valve Check, Illustrated
DIY: Shiver Valve Check, Illustrated By Petemoss, AF1 Forum Tools needed: 4mm allen wrench to remove all the fairing pieces 2.5mm allen wrench to remove battery holder 5mm allen wrench for valve cover
More informationHow to install Front Brake Pads on your GT, V6
Time Necessary: Approximately 1.5 hours Tools Required: How to install Front Brake Pads on your 99-04 GT, V6 Jack Jack stands Torque wrench Ratchet Lug wrench 15mm socket 12mm socket Large C-clamp Syringe
More informationInstalling Rear Brake Pads on a WK Jeep
Installing Rear Brake Pads on a WK Jeep Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your rear brake pads. This is what I did after
More informationINSTALLATION PROCESS: FK003D945-7 Complete Front, Rear, and Clutch A.B.S. KIT Harley Davidson FLH Touring Models
INSTALLATION PROCESS: FK003D945-7 Complete Front, Rear, and Clutch A.B.S. KIT 2014-2017 Harley Davidson FLH Touring Models Parts List: 4 Lines 1 Brake Light Switch Adapter 7 Single banjo bolts 2 Caliper
More informationRekluse Motor Sports. The e-axle KTM. Installation Guide Copyright 2006 Rekluse Motor Sports e-axle Revision 1.
Rekluse Motor Sports The e-axle 2003 2007 KTM Installation Guide Copyright 2006 Rekluse Motor Sports e-axle Revision 1.000 RMS 2733 195-2733C Manual Revision: 032207 Rekluse Motor Sports, Inc. 110 E. 43
More informationWARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil.
WARNING: the engine does not come with oil in it. Please fill the oil before starting. The 200cc hardknock requires 9/10 of a quart of oil. Things needed for assembly. -2 tubes of blue loc-tite. I don
More informationThanks for Ordering The Vulcan 800A Front Wheel Adapter from READ THIS BEFORE UNPACKING YOUR KIT!
Thanks for Ordering The Vulcan 800A Front Wheel Adapter from READ THIS BEFORE UNPACKING YOUR KIT! This instruction booklet contains detailed steps for installation of your Vulcan 800A Front Wheel Adapter
More informationINSTALLATION GUIDE. Kawasaki KLR Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE Kawasaki KLR650 191-640 Manual Revision: 030308 2007 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714
More informationHow I installed new brake pads on my i with Sport Package (should be fine for other E39 s) By Robert B.
How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) How I installed new brake pads on my 1999 528i with Sport Package (should be fine for other E39 s) By
More informationOVERHAULING BRAKE CALIPERS GUIDE by Mr. Stefnwolf. This guide is for a 1982 GSX750ET but I expect most of the GS series to be similar if not the same.
OVERHAULING BRAKE CALIPERS GUIDE by Mr. Stefnwolf This guide is for a 1982 GSX750ET but I expect most of the GS series to be similar if not the same. Badly corroded calipers (caused by moisture in the
More informationSherco Setup and Lubrication Guide
Sherco Setup and This guide is designed to provide the Sherco owner with instructions on how to: Set up a new bike Clean and re-oil the air filter Change the transmission oil Change the fork oil Repack
More informationHow To: Fix That Ugly Hanging E-Brake Cable A CFans Members Mod Project by dirtydawg
How To: Fix That Ugly Hanging E-Brake Cable A CFans Members Mod Project by dirtydawg Skill Level: Easy Disclaimer: Please use caution and seek professional assistance when necessary. ColoradoFans.com,
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationThere was some debate whether or not there was a write up, with Pictures, for replacing the ignition switch.
Replacing the Ignition Switch - Step by Step with Pictures. http://forums.audiworld.com/showthread.php?p=18927576 (Corey 02ALMSTT) (With updates/corrections by Dave F.) February 1, 2013 (I = Corey, mostly)
More informationHow to Replace the Main Axle Gear on the Bachmann Spectrum GScale using the NWSL # upgrade gear.
How to Replace the Main Axle Gear on the Bachmann Spectrum GScale 4-4-0 and 2-6-0 Mogul (2001era), using the NWSL #2223-6 upgrade gear. By Paul M. Newitt (all text and photos Copyright Paul M. Newitt,
More informationRekluse Motor Sports. The z-start Clutch GAS GAS. 200, 250, and strokes. 400 and strokes
Rekluse Motor Sports The z-start Clutch GAS GAS 200, 250, and 300 2-strokes 400 and 450 4-strokes Installation Guide Copyright 2002-2004 Rekluse Motor Sports z-start Revision 3.000 RMS100 Gas Gas z-start
More informationN62 & N62-TU Valve Stem Seal Tool Kit
N62 & N62-TU Valve Stem Seal Tool Kit Part #: AGA-N62-VST-K Problem: You have a smoking BMW due to bad valve stem seals. The valve stem seal problem is that the old valve stem seal becomes hard over time
More informationRear Parking Brake Cable (93 Cobra)
Rear Parking Brake Cable (93 Cobra) Materials in the box: Brake Cable Tools Needed: One jack and four jack stands. One socket wrench with a 12mm, 13mm ( ½ inch, 12 point DEEP WALL DO NOT FORGET THIS) and
More informationConnecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
More informationRear Wheel Removal (by BassCliff)
Rear Wheel Removal (by BassCliff) Hello to my GS riding friends! After picking up a nail in my rear tire (while on the freeway at 75mph!) I thought I would take a few pictures to help illustrate the rear
More informationINSTALLATION GUIDE CRF150R Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE CRF150R 191-810 Manual Revision: 032508 2002 Rekluse Motor Sports Rekluse Motor Sports, Inc. 110 E. 43rd Street Boise, Idaho 83714 208-426-0659
More informationupper and lower ball joints ( I went with Moog from rockauto.com): two K80026 and two K8607T
Parts required: two 5C3Z*4A322*AA = hub / steering knuckle o-ring two AC3Z*1S175*A = updated axle shaft "dust seal" two 5C3Z*3254*A = steering knuckle / axle shaft seal upper and lower ball joints ( I
More informationMopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion
Mopar 8 3/4 & 9 3/4 (Dana) Installation Instructions Rear Disc Conversion This kit is for either Mopar 8 ¾ or Mopar 9 ¾ (Dana). This kit is designed to work with axles with either GM 5 x 4.75 Bolt Pattern
More informationReplace C1U-H47 Carburator on Homelite
Replace C1U-H47 Carburator on Homelite Weed Whacker It's cheaper, quicker, and more reliable to replace your carburetor with a new one, rather than rebuilding it. Written By: Gil ifixit CC BY-NC-SA www.ifixit.com
More informationM52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit
Home BMW Solutions Porsche Solutions DIY Tech Engine Services Dyno Services Machining About Contact Store Tool Rental M52tu-M54 VANOS Assembly & Timing Using G.A.S. Professional Cam Tool Kit This procedure
More informationRekluse Motor Sports. The z-start Clutch CRF 250R. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision RMS112 CRF 250R
Rekluse Motor Sports The z-start Clutch CRF 250R Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.000 RMS112 CRF 250R 191-212 Manual Revision: 091205 Rekluse Motor Sports, Inc.
More informationFitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE
Part Number DA1112 Fitting Instructions For The TDV6 EGR Blanking Kit To A 2006 Model Discovery 3 TDV6 GHSE You do this modification at your own risk. Britpart won t be held responsible for what is written
More information6th generation (2015+) Mustang Harness Mount Bar Installation Instructions
R-1180 6th generation (2015+) Mustang Harness Mount Bar Installation Instructions A. Install harness bar 1. Remove front seats. First remove the plastic bolt covers front and rear using a small flat head
More informationApplication(s) > Items Supplied > Instruction Manual >
301 E. La Palma Ave., Yorba Linda, Ca 97 Ph. 714.69.10, Fax. 714.69.5016 Items Supplied > Application(s) > www.fi000r.com 1 Fi000R Fuel Injection Module Zip Ties 1 Velcro Strip Oxygen Sensor Eliminators
More informationINSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE CROSS COUNTRY / CROSS ROADS / HARD BALL RAKE KIT
INSTALLATION INSTRUCTIONS FOR THE MOTOR TRIKE CROSS COUNTRY / CROSS ROADS / HARD BALL RAKE KIT Thank you for choosing the Motor Trike Cross Country / Cross Roads / Hard Ball rake kit. We ask that you read
More informationSetting The Sag. We ve gathered up a few tutorials on setting the sag. Read them over and decide which one makes the most sense to you.
Setting The Sag Setting the sag on your bike is the first step in correctly adjusting your suspension. We here at MotorPsycle.com want you to have a safe, great-handling bike. A suspension set up too hard
More informationRekluse Motor Sports. The z-start Clutch KTM LC4 ( )
Rekluse Motor Sports The z-start Clutch KTM LC4 (1999 2005) Installation Guide Copyright 2002-2004 Rekluse Motor Sports z-start Revision 3.000 RMS630 KTM LC4 191-280 Manual Revision: 103105 Rekluse Motor
More information55-64 Full Size Chevy
55-64 Full Size Chevy Installation Instructions Power Disc Conversion 9 slimline booster pictured Your new disc brake conversion kit can be bolted up with standard hand tools. The only tools you may not
More informationSignature Series A/F/X Body GM Installation Instructions Power Disc Conversion
Signature Series A/F/X Body GM Installation Instructions Power Disc Conversion 64-72 A Body / 67-69 F Body / 62-74 X Body Your new disc brake conversion kit can be bolted up with standard hand tools. The
More informationFinal Assembly Instructions Portside Cruiser
Final Assembly Instructions Portside Cruiser Thank you for buying your new bicycle from L.L.Bean. Read these instructions carefully before beginning the final assembly. Prior to shipping, our expert cycling
More informationFull Size GM Installation Instructions
Full Size GM Installation Instructions Rear Disc Conversion 55 64 Full Size GM (Impala, Bel Air, etc.) This kit is for axle with a 3 3/8 spread center to center on the top two bolt holes (pictured left).
More informationRekluse Motor Sports. The z-start Clutch CRF 250X. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision RMS116 CRF 250X
Rekluse Motor Sports The z-start Clutch CRF 250X Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.000 RMS116 CRF 250X 191-216 Manual Revision: 103105 Rekluse Motor Sports, inc.
More informationSTEPS FOR REMOVING REAR ASHTRAY & CUP HOLDER, CENTER ARMREST, E- BRAKE CONSOLE, FRONT ASHTRAY, LOWER CENTER CONSOLE AND GLOVE BOX
Please give credit where credit is due! This DIY was completed ENTIRELY by the hardest working VW Vortex moderator on the site!! Gary Thompson, Ph.D. - vortex ID VGRT6, email address vgrt6@yahoo.com. Please
More informationRekluse Motor Sports, Inc. The z-start Clutch. Husaberg ( )
Rekluse Motor Sports, Inc. The z-start Clutch Husaberg (1989-2003) Installation Guide Copyright 2002-2004 Rekluse Motor Sports z-start Revision 3.000 RMS125 Husaberg 89-03 191-225 Manual Revision: 012805
More informationArrow Shark 2015 E-Starter V4 Owner Manual
Arrow Shark 2015 E-Starter V4 Owner Manual The Arrow Shark E-Starter V3 has successfully been available in the market for over three years now. During that time, we have never stopped seeking ways to improve
More informationFord Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours
Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Tools Required: Ratchet and socket set Torque wrench Large adjustable wrench Needle nose pliers A dozen
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More informationRekluse Motor Sports. The z-start Clutch. Cannondale
Rekluse Motor Sports The z-start Clutch Cannondale Installation Guide Copyright 2002-2004 Rekluse Motor Sports z-start Revision 3.000 RMS105 Cannondale 191-205 Manual Revision: 091304 Rekluse Motor Sports,
More informationHow many miles do you have on that KLR? Last update: September 3, 2018
How many miles do you have on that KLR? Last update: September 3, 2018 A red-letter day for my KLR back in 2013. The addition of the "1" and the comma seemed like a requirement. As the miles pile on my
More informationRekluse Motor Sports. The z-start Clutch DRZ400 KLX400. Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.
Rekluse Motor Sports The z-start Clutch DRZ400 KLX400 Installation Guide Copyright 2002 Rekluse Motor Sports z-start Revision 3.000 RMS160 KLX400 DRZ400 z-start Clutch 191-260 Manual Revision: 103105 Rekluse
More informationCHAPTER 2: HEAD, BARREL, SUMP, BIGENDS, ALTERNATOR
CHAPTER 2: HEAD, BARREL, SUMP, BIGENDS, ALTERNATOR Posted on the Wildguzzi forum by Pete Roper: December 10, 2005: Contents: Head, barrel and sump off, bigend bearings, alternator off Pic 2-01: Note that
More informationCALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL
CALIFORNIA TRIMMER MOWER MAINTENANCE MANUAL 2 Table of Contents Section 1: General Information Page Handle Assembly Instructions 4 Maintenance All Models 6 Oil Change Procedures All Models 9 Height Adjustment
More informationDoor Panel Removal & Window Stop Adjustment
Door Panel Removal & Window Stop Adjustment By: Jeff Wolford Disclaimer: This is simply an article of how I fixed my car. I m not responsible if you break, scratch, or mess up anything following my example.
More informationLowering Spring Installation on a Mustang GT
Lowering Spring Installation on a 99-04 Mustang GT This installation is very the same installation that many of the 79-04 Mustangs excluding Cobra require. Time to install: 2-3 hours to do alone with a
More informationSteve Saunders Goldwing Forums > Steve Saunders Goldwing Forums > Reference and FAQ Forum > Balancing GL1500 Carbs
Skype update. You can now easily activate Skype in your forum profile, allowing you to talk in real time with other forum members. Just go to MY ACCOUNT, click PROFILE and scroll down to the Skype field,
More informationInstallation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
More information2003 CR-V - A/T Shift Cable Replacement-Print Preview
Page 1 of 7 2003 CR-V - A/T Shift Cable Replacement 1. Raise the front of the vehicle, or lift the vehicle up, and make sure it is securely supported. 2. Remove the driver's dashboard lower cover, and
More informationBe sure to read and go over all pages before you start your installation
Yamaha Gen-2 V-MaxV Holeshot Superbike Bars Installation Guide Pre-Installation Note Be sure to read and go over all pages before you start your installation Preparation for Installation A) It is recommended
More informationParking Brake Components*
CORVETTE PARKING BRAKE REBUILD '65 TO 67 (AND BEYOND) Tim Welsh and Dave Zuberer The information here was compiled by Tim Welsh (Buns) and Dave Zuberer (DZVette) and is based on our experiences in changing
More informationPerformance Brake Caliper Guide Bushing Set Installation Guide
Performance Brake Caliper Guide Bushing Set Installation Guide Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those
More informationInstalling LED lights in a Hypercharger By Keith Edwards Joker s Wild! (Wildjokr)
Installing LED lights in a Hypercharger By Keith Edwards Joker s Wild! (Wildjokr) THINGS YOU WILL NEED: A Hypercharger (duh!) LEDs (The ones I got were from Benny Bryant at Fantasies on Wheels in Sylacauga,
More informationCHASSIS CONTENTS FRONT WHEEL 6-1 FRONT BRAKE 6-6 FRONT FORK 6-14 STEERING STEM 6-20 REAR WHEEL AND REAR BRAKE 6-25 SUSPENSION 6-31 REAR SWING ARM 6-36
CHASSIS CONTENTS FRONT WHEEL 6-1 FRONT BRAKE 6-6 FRONT FORK 6-14 STEERING STEM 6-20 REAR WHEEL AND REAR BRAKE 6-25 SUSPENSION 6-31 REAR SWING ARM 6-36 6 6-1 CHASSIS FRONT WHEEL REMOVAL Support the machine
More informationThis write-up is subject to revision. PM me, eb2143 at tdiclub.com and I will update it if there are inaccuracies, typos, missing information, etc.
1 A4 Door Switch Replacement, 1.0 Notes on this guide: The following guide is mostly a combination of two write-ups by VgRt6 on Vwvortex.com. Specific threads located here: http://forums.vwvortex.com/showthread.php?1015107
More informationFull Size GM Installation Instructions Rear Disc Conversion
Full Size GM Installation Instructions Rear Disc Conversion 65 68 Full Size GM (Impala, Bel Air, etc.) This kit is for axles with a 3 3/8 spread center to center on the top two bolt holes (pictured left).
More informationRekluse Motor Sports. The z-start Clutch. Husaberg
Rekluse Motor Sports The z-start Clutch Husaberg Installation Guide Copyright 2002-2004 Rekluse Motor Sports z-start Revision 3.000 RMS126 Husaberg 04+ 191-226 Rekluse Motor Sports, inc. 110 E. 43 rd Street
More informationLMB-C6 CF Senior Member
LMB-C6 CF Senior Member Rotor install DIY... ****** FRONT: ****** Remove the wheel. To remove the rotor you need to remove the caliper and the bracket. There are 2 bolts for the caliper (top smaller bolt
More informationMustang 7.5 Limited Slip Differential (28 Spline) V8; V6:
Mustang 7.5 Limited Slip Differential (28 Spline) 79-85 V8; 86-10 V6: Required Tools: Ratchet Wrench Torque Wrench 1/2", 5/16, 3/4", 12mm and 15mm Sockets Lug nut Wrench Dial Indicator Digital Measuring
More informationBMW E46 Convertible Hydraulic Line #23 Replacement Guide Created by taylor192 of E46Fanatics.com
BMW E46 Convertible Hydraulic Line #23 Replacement Guide Created by taylor192 of E46Fanatics.com BMW E46 Line #23 Replacment Guide, page 1 of 23 Background: Line #23 runs from the valve block on the driver's
More informationInstalling the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version)
Installing the Wireless Charging upgrade kit in a 2018 XT5 (Platinum version) September 2, 2018 Tools needed: Wireless charger upgrade kit Plastic trim tools 7 mm nut driver Background: I purchased the
More informationAmTryke Adult Recumbent Model JT2000 #50-FC-2000
AmTryke Adult Recumbent Model JT2000 #50-FC-2000 TOOLS Needed for Assembly 5 mm Allen Wrench 8 mm Socket or Wrench 10 mm Socket or Wrench 14 mm Socket or Wrench 15 mm Socket or Wrench 22 mm Socket or Adjustable
More informationThis document provides instructions for removing and installing a Front Wheel / Rotor on a Ducati Superbike. The torque values used are for the 748/916/996 from 1994 to 2001 and may be applicable for later
More informationTorque specifications Stainless steel ft. lbs Aluminum ft. lbs
INSTALLATION PROCESS: FK003D802-8 Complete Brake Line Kit 2013 Kawasaki VN1700 Voyager Custom ABS 2013 Kawasaki VN1700 Vaquero ABS Torque specifications Stainless steel 15-17 ft. lbs Aluminum 12-15 ft.
More informationModifications to my KLR Last update: May 30, 2016
Modifications to my KLR Last update: May 30, 2016 This article discusses modifications from stock that I have made to my 2004 KLR... primarily to either make it last longer, safer to ride, or easier to
More informationA/F/X Body GM Installation Instructions Manual Disc Conversion
A/F/X Body GM Installation Instructions Manual Disc Conversion 64-72 A Body / 67-69 F Body / 62-74 X Body DBMC09 & PVK71 pictured above (Booster, master & valve setups may vary by upgrades selected) Your
More information60 76 A Body Mopar Power Disc Conversion Installation Instructions
62-72 B & E BodyMopar 60 76 A Body Mopar Power Disc Conversion Installation Instructions Special A-Body only parts shown below (In addition to parts above for A-Body cars, part # MDC66DC & MDC46DC) Your
More informationA/F/X Body GM Installation Instructions
A/F/X Body GM Installation Instructions Power Disc Conversion 64-72 A Body / 67-69 F Body / 68-74 X Body 9 slimline booster pictured Your new disc brake conversion kit can be bolted up with standard hand
More informationGearbox Assembly 101. Introduction. Before Beginning. By Mark Schutzer 4/13/06
Gearbox Assembly 101 By Mark Schutzer 4/13/06 Introduction If you are planning to re-motor an old brass locomotive you may want to upgrade to a new gearbox at the same time. The early 60 s and 70 s gearboxes
More informationPORSCHE V r Valve Timing Instructions. Copyright 2009 Written by Mike Frye Edited my Adam G.
PORSCHE 928 32V r Valve Timing Instructions Copyright 2009 Written by Mike Frye Edited my Adam G. Sections: Overview.3 Disclaimer/warnings/things to watch for 4 Terms and naming conventions used in this
More information1986 Rear Disk Brake Upgrade. All hard lines mounted to the rear axle with mounting screws. 1/4" fittings
1986 Rear Disk Brake Upgrade Being well prepared for a project of this size is the key to success. I thought I was well prepared by doing a lot of research and getting all of the required parts before
More informationOwners manual. Öhlins Superbike front fork FG 170
Owners manual Öhlins Superbike front fork FG 0 Including: Setting up your fork Changing springs and seals Service the fork Trouble shooting Technical info Spare parts & tools Öhlins super bike front fork
More informationTSS Fit Kit Installation Instructions Timbersled Snow Bike System
TSS Fit Kit Installation Instructions Timbersled Snow Bike System Information needed before you start: Read the entire installation instructions before starting. The instruction sheet is universal for
More informationChanging the Struts on a WK Jeep CRD
Changing the Struts on a WK Jeep CRD Step by Step By Chirpz Disclaimer: I do not claim that this procedure is the right way or even the best way to change your struts. This is what I did after reading
More informationwhat you need to do is hit the taper housing as hard as you can with your hammers AT THE SAME TIME and at a slight angle, what will happen is you
first things first, get the car on axle stands and the wheels off. Open the bonnet to let more light through to the area in which you'll be working. The following guide shows the passenger side being done
More informationINSTALLATION & USER S GUIDE
REKLUSE MOTOR SPORTS The Rekluse Core EXP Kit with Adjustable Slave Cylinder INSTALLATION & USER S GUIDE Doc ID: 191-7704A Doc Rev: 102915 OVERVIEW This kit replaces the OEM core clutch components including
More informationA /F/X Body Instruction Packet Rear Disc Conversion
A /F/X Body Instruction Packet Rear Disc Conversion 64-72 A Body / 67-81 F Body / 62-74 X Body This kit is for axles with a 3 1/8 spread center to center on the top two bolt holes (pictured left). If your
More informationBrake System Rebuilding the brake calipers
Page 1 of 39 Brake System Rebuilding the brake calipers Written by the backyard hack mechanic Sean750 Document history: # 14 Jan 2004 added pictures of rear caliper rebuild kit # 13 Nov 2004 added more
More informationINSTALLATION GUIDE. KTM 125, 144, Stroke KTM 250, Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF Manual Revision:
REKLUSE MOTOR SPORTS The z-start Pro Clutch INSTALLATION GUIDE KTM 125, 144, 200 2-Stroke KTM 250, 300 2-Stroke KTM 250 SXF, XC, XC-W KTM 450, 505 SXF 191-836 Manual Revision: 050307 2002 Rekluse Motor
More informationCentral Braking Castors
Central Braking Castors Congratulations for choosing Australia's famous Fallshaw castors Version 3 These instructions are in 4 sections... 1/ Configuration Preferred combinations of castor layout. 2/ Requirements
More informationDIY Bi-Metallic Strip
DIY Bi-Metallic Strip An introduction to the applications of thermal expansion and two-way switching. Written By: Mahaaveer BN 2018 Page 1 of 14 INTRODUCTION A bi-metallic strip is used to convert a temperature
More informationSteering Damper for FLH Harley-Davidson Bikes/Trikes
Steering Damper for FLH Harley-Davidson Bikes/Trikes I have spoken with several HD Touring model trikers, who are looking for increased feel in the steering department. Some want to cure a slight wobble
More informationAt Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job.
At Mark's suggestion I thought I'd write this up so future Coupe lovers can have as much fun* as I did with this job. My enormous thanks to forum members, particularly glorfindel, for their advice when
More informationM1A1 Thompson Upgrade
M1A1 Thompson Upgrade If you are mechanically inclined at all. This should be no problem. I'll start off with a list of things you will need. Thompson M1A1 Whisky Cigarettes Tools: Flat screwdriver No.
More informationUSE THE PARTS LIST BELOW TO MAKE SURE YOUR KIT IS COMPLETE BEFORE INSTALLATION. IF ANY PIECES ARE MISSING, PLEASE CONTACT:
1962-1967 Chevy Nova Pro-Touring Front Suspension Installation Instructions Tech line: 1-855-693-1259 www.totalcostinvolved.com Read and understand these instructions before starting any work! USE THE
More informationInstalling Stage II Kit KTM EXC/F ( )
Installing Stage II Kit KTM EXC/F (2017-18) Thank you for choosing 2Tall Racing. We have spent countless hours of R&D and testing to ensure you receive the highest quality product on the market today.
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationBarton Short Throw Shifter 11/12 V6, GT Mustang:
Barton Short Throw Shifter 11/12 V6, GT Mustang: Tools Required: 10mm deep socket Socket wrench 10 extension for socket wrench Jack Jack stand Small piece of wood Small hook tool (recommended) *can be
More informationCHASSIS CONTENTS EXTERIOR PARTS 7-1 FRONT WHEEL 7-2 FRONT BRAKE 7-6 HANDLEBARS 7-13 FRONT FORK 7-15 STEERING 7-23 REAR WHEEL 7-26 REAR BRAKE 7-30
CHASSIS CONTENTS EXTERIOR PARTS 7- FRONT WHEEL 7-2 FRONT BRAKE 7-6 HANDLEBARS 7-3 FRONT FORK 7-5 STEERING 7-23 REAR WHEEL 7-26 REAR BRAKE 7-30 REAR SHOCK ABSORBER 7-32 SWING ARM 7-33 7 7- CHASSIS EXTERIOR
More informationThanks for Ordering The Honda VLX Adjustable Lowering Kit from READ THIS BEFORE UNPACKING YOUR KIT!
Thanks for Ordering The Honda VLX Adjustable Lowering Kit from READ THIS BEFORE UNPACKING YOUR KIT! This instruction booklet contains detailed steps for installing the Adjustable Lowering kit on your Honda
More informationRear End Installation and Bearing Kit - 8.8in (86-12 V8; V6)
Rear End Installation and Bearing Kit - 8.8in (86-12 V8; 11-13 V6) Tools Required: Jack Stands 5 Floor Jack 2 Oil Pans 1 Wheel Blocks 2 Differential Oil 3 qts Friction Modifier 3 bottles Tube of Black
More information