PFA Tube Fittings. Temperatures from 70 to 400ºF (20 to 204 C) Working pressures up to 275 psig (18.9 bar) Sizes from 1/8 to 1/2 in.
|
|
|
- Abigayle Blankenship
- 6 years ago
- Views:
Transcription
1 PF Fittings 1 PF Fittings PF Temperatures from 70 to 400ºF (20 to 204 C) Working pressures up to 275 psig (18.9 bar) s from 1/8 to 1/2
2 2 Fittings PF Features udible click ensures tubing is inserted properly. Visual indication of proper pull-up: no gap between body hex and hex nut hex flat alignment. Smooth, molded internal wetted surfaces reduce potential for system contamination. Grooved tubing allows for higher working pressure. Wrench assembly avoids the potentially unsafe practices of hand assembly and disassembly. Materials Fittings Molded PF/STM 3307 Type I Pressure-Temperature Ratings Pressure ratings are for Swagelok PF tube fittings used with properly grooved Swagelok PF tubing. Wall, , 1/8 1/4 1/4 3/8 1/2 Temperature, F ( C) Working Pressure, psig (bar) 70 (20) 275 (18.9) 200 (13.7) 275 (18.9) 180 (12.4) 125 (8.6) 100 (37) 245 (16.8) 180 (12.4) 245 (16.8) 155 (10.6) 115 (7.9) 200 (93) 145 (9.9) 110 (7.5) 145 (9.9) 93 (6.4) 68 (4.6) 300 (148) 87 (5.9) 64 (4.4) 87 (5.9) 48 (3.3) 32 (2.2) 400 (204) 47 (3.2) 34 (2.3) 47 (3.2) 11 (0.75) 11 (0.75) Information and imensions imensions, in inches (millimeters), are for reference only and are subject to change. imensions shown with Swagelok nuts finger-tight. dimensions refer to the minimum opening. Unions F 1/8 PF (36.8) 0.50 (12.7) 0.09 (2.3) 1/2 1/4 PF (43.2) 0.60 (15.2) 0.19 (4.8) 5/8 3/8 PF (45.7) 0.67 (17.0) 0.28 (7.1) 13/16 1/2 PF (52.1) 0.90 (22.9) 0.41 (10.4) 1 Bulkhead Unions x F 1/4 PF (61.5) 1.41 (35.8) 0.60 (15.2) 0.19 (4.8) 7/8 Panel hole size is 0.70 (17.8 mm); maximum panel thickness is 0.44 (11.2 mm). x Reducing Unions x x F 3/8 to 1/4 PF (45.0) 0.67 (17.0) 0.60 (15.2) 0.19 (4.8) 13/16 1/2 to 1/4 PF (48.5) 0.90 (22.9) 0.60 (15.2) 0.19 (4.8) 1 1/2 to 3/8 PF (49.3) 0.90 (22.9) 0.67 (17.0) 0.28 (7.1) 1
3 PF Fittings 3 Information and imensions imensions, in inches (millimeters), are for reference only and are subject to change. imensions shown with Swagelok nuts finger-tight. dimensions refer to the minimum opening. PF Union lbows F wrench F 1/8 PF (23.1) 0.50 (12.7) 0.09 (2.3) 1/2 1/4 PF (28.7) 0.60 (15.2) 0.19 (4.8) 5/8 3/8 PF (31.2) 0.67 (17.0) 0.28 (7.1) 13/16 1/2 PF (36.8) 0.90 (22.9) 0.41 (10.4) 1 Union Tees F wrench x x F 1/8 PF (46.2) 0.91 (23.1) 0.50 (12.7) 0.09 (2.3) 1/2 1/4 PF (57.4) 1.13 (28.7) 0.60 (15.2) 0.19 (4.8) 5/8 3/8 PF (62.5) 1.23 (31.2) 0.67 (17.0) 0.28 (7.1) 13/16 1/2 PF (73.7) 1.45 (36.8) 0.90 (22.9) 0.41 (10.4) 1 x Male Connectors NPT F 1/8 1/8 PF (30.7) 0.50 (12.7) 0.09 (2.3) 1/2 1/4 1/8 PF (34.5) 1/4 PF (39.1) 0.60 (15.2) 0.19 (4.8) 5/8 3/8 1/4 PF /8 PF (40.6) 0.67 (17.0) 0.28 (7.1) 13/16 1/2 3/8 PF (44.2) 1/2 PF (49.0) 0.90 (22.9) 0.41 (10.4) 1 Male lbows F wrench H NPT F H 1/8 1/8 PF (23.1) 0.50 (12.7) 0.09 (2.3) 1/ (17.0) 1/4 1/8 PF (19.8) 1.13 (28.7) 0.60 (15.2) 0.19 (4.8) 5/8 1/4 PF (24.4) 3/8 1/4 PF /8 PF (31.2) 0.67 (17.0) 0.28 (7.1) 13/ (26.2) 1/2 3/8 PF (29.0) 1.45 (36.8) 0.90 (22.9) 0.41 (10.4) 1 1/2 PF (33.8)
4 4 Fittings PF Information and imensions imensions, in inches (millimeters), are for reference only and are subject to change. imensions shown with Swagelok nuts finger-tight. dimensions refer to the minimum opening. Back Ferrules ➀ 1/4 PF /8 PF /2 PF ➀ 1/8 back ferrule integral with nut. Front Ferrules 1/8 T-203-1➀ 1/4 PF /8 PF /2 PF ➀ PTF material. Plugs 1/8 PF-220-P 1/4 PF-420-P 3/8 PF-620-P 1/2 PF-820-P Nuts 1/8 1/4, 3/8, 1/2 L G flat G flat 1/8 PF-222-1➀ 1/2 1/4 PF /8 3/8 PF /16 1/2 PF imensions (mm) G L 0.57 (14.5) 0.65 (16.5) 0.68 (17.3) 0.79 (20.1) Caps F 1/8 PF-220-C 0.83 (21.1) 0.50 (12.7) 1/2 1/4 PF-420-C 0.98 (24.9) 0.60 (15.2) 5/8 3/8 PF-620-C 1.04 (26.4) 0.67 (17.0) 13/16 1/2 PF-820-C 1.18 (30.0) 0.90 (22.9) 1 ➀ 1/8 back ferrule integral with nut. L Installation PF tubing MUST be grooved for use with PF tube fittings. Use the Swagelok groove cutter tool. 1. Insert grooved PF tubing into the Swagelok PF tube fitting until a clicking sound is heard. 2. While holding fitting body steady, tighten the blue nut until there is no gap between the nut and body hexes. 3. Continue tightening until the nut and body hexes are aligned. PF Tubing and Tools For PF tubing in accordance with STM 3307, Type II, in 1/8 to 1 and 6 to 12 mm sizes, see the Swagelok Hose and Flexible Tubing catalog (MS ). The catalog also contains ordering information for the Swagelok groove cutter tool. Caution: o not mix or interchange parts with those of other manufacturers. MS-01-05, R9, October 2017
5 bout this document Thank you for downloading this electronic catalog, which is part of General Product catalog Swagelok published in print. This type of electronic catalog is updated as new information arises or revisions, which may be more current than the printed version. Swagelok Company is a major developer and provider of fluid system solutions, including products, integration solutions and services for industry research, instrumentation, pharmaceutical, oil and gas, power, petrochemical, alternative fuels, and semiconductor. Our manufacturing facilities, research, service and distribution facilities support a global network of more than 200 authorized sales and service centers in 57 countries. Visit to locate your Swagelok representative and obtain any information on features, technical information and product references, or to learn about the variety of services available only through authorized sales centers and service Swagelok. Safe Product Selection When selecting a product, the total system design must be considered to ensure safe, trouble-free performance. Function, material compatibility, adequate ratings, proper installation, operation, and maintenance are the responsibilities of the system designer and user. Warranty Information Swagelok products are backed by The Swagelok Limited Lifetime Warranty. For a copy, visit your Swagelok Web site or contact your authorized Swagelok representative. Swagelok, Ferrule-Pak, Goop, Hinging-Colleting, IGC, Kenmac, Micro-Fit, Nupro, Snoop, Sno-Trik, SWK, VCO, VCR, Ultra- Torr, Whitey TM Swagelok Company flas TM sahi Glass Co. Ltd. L-6XN TM llegheny Ludlum Corporation utoc TM utodesk, Inc. CS TM Canadian Standards ssociation evicenet TM OV Kalrez, Krytox TM upont lgiloy TM lgiloy Specialty Metals FM TM FM Global Grafoil TM GrafTech International Holdings, Inc. MC TM MC Valves Inc. Microsoft, Windows TM Microsoft Corp. NC TM NC International Nitronic TM K Steel Corporation picofast TM HansTurck KG Pillar TM Nippon Pillar Packing Company, Ltd. Rapid Tap TM Relton Corporation 15-7 PH, 17-7 PH TM K Steel Corp. Sandvik TM SandvikB Silconert TM Silcotek Corporation Simriz TM Freudenberg-NOK SolidWorks TM SolidWorks Corporation 2017 Swagelok Company
PFA Needle Valves. 4RP Series. High-purity PFA material. Working pressures up to 180 psig (12.4 bar) Temperatures up to 300 F (148 C)
Needle Valves 4RP Series 1 www.swagelok.com Needle Valves 4RP Series High-purity material Working pressures up to 180 psig (12.4 bar) Temperatures up to 300 F (148 C) 1/4, 3/8, and 1/2 in. Swagelok tube
Pipe Fittings. 1/16 to 1 in. sizes. 316 stainless steel, brass, and carbon steel. NPT, ISO/BSP, and SAE threads.
Pipe Fittings 1 www.swagelok.com Pipe Fittings PIP 1/16 to 1 sizes 316 stainless steel, brass, and carbon steel, /SP, and S threads 2 Weld, VCR, VCO, Pipe, and Vacuum Fittings Contents Nipples Page 4 Crosses
Plug Valves. P4T and P6T Series. Working pressures up to 3000 psig (206 bar) Swagelok tube fitting and NPT and ISO tapered pipe end connections
Plug Valves P4T and P6T Series 1 www.swagelok.com Plug Valves P4T and P6T Series Working pressures up to 3000 psig (206 bar) Swagelok tube fitting and NPT and ISO tapered pipe end connections 1/8 through
Toggle Valves. OG, 1G, and 92 Series. Manual and pneumatically actuated models. Straight, angle, and cross body patterns
Toggle Valves OG,, and 92 1 www.swagelok.com Toggle Valves OG,, and 92 Manual and pneumatically actuated models Straight, angle, and cross body patterns 316 SS and brass body materials 2 Needle and Metering
Diaphragm Valves. DL and DS Series. Packless, all-metal containment. Working pressures from vacuum to 3500 psig (241 bar)
Diaphragm Valves DL and 1 www.swagelok.com Diaphragm Valves DIPHRGM DL and Packless, all-metal containment Working pressures from vacuum to 3500 psig (241 bar) Temperatures from 100 to 250 F ( 73 to 121
Springless Diaphragm Valves (1.125 in.)
Springless Diaphragm Valves ( in.) DE Series 1 www.swagelok.com Springless Diaphragm Valves ( in.) For Modular Gas Systems DE Series in. C-seal and W-seal designs Available in two- and three-port configurations
Gaugeable Alloy 2507 Super Duplex Tube Fittings
Gaugeable lloy 2507 Super uplex Fittings 1 www.swagelok.com SUPR UPLX Gaugeable lloy 2507 Super uplex Fittings xcellent corrosion resistance in chloride-containing environments dvanced-geometry back ferrule
Swagelok Alternative Fuel Service (AFS) Ball Valves
Swagelok Alternative Fuel Service () Ball Valves 461 Swagelok Alternative Fuel Service () Ball Valves For High-Pressure, High-Flow Applications Swagelok Ball Valves Working pressures up to 6000 psig (413
Bellows- and Diaphragm-Sealed Multiport and Elbow Valves and Monoblock Manifolds
ellows- and Diaphragm-Sealed Multiport and Elbow Valves and Monoblock Manifolds 1 www.swagelok.com ellows- and Diaphragm-Sealed Multiport and Elbow Valves and Monoblock Manifolds Selection Guide EOW VVES
Check Valves. C, CA, CH, CP, and CPA Series. Working pressures up to 6000 psig (413 bar) Adjustable and fixed cracking pressures
Check Valves C, CA, CH, CP, and CPA Series 1 www.swagelok.com Check Valves C, CA, CH, CP, and CPA Series Working pressures up to 6000 psig (413 bar) Adjustable and fixed cracking pressures Variety of end
Check Valves. C, CA, CH, CP, and CPA Series. Working pressures up to 6000 psig (413 bar) Adjustable and fixed cracking pressures
Check Valves C, CA, CH, CP, and CPA Series Working pressures up to 6000 psig (413 bar) Adjustable and fixed cracking pressures Variety of end connections 316 stainless steel and brass materials Check Valves
Tubing Tools and Accessories
Tubing Tools and Accessories 1 www.swagelok.com Tubing Tools and Accessories Products Electric, bench top, and hand tube benders preparation tools 2 Tubing, Tubing Tools, and Welding System Contents ers
Filters. FW, F, and TF Series. Remove system particulate contaminants. Gas and liquid service. 1/8 to 1/2 in. and 3 to 12 mm end connections
s FW, F, and TF Series 1 www.swagelok.com s FW, F, and TF Series Remove system particulate contaminants Gas and liquid service 1/8 to 1/2 in. and 3 to 12 mm end connections Stainless steel and brass materials
Stream Selector System
Selector System Series 1 www.swagelok.com Selector System For Process Analyzer Applications Series Provides double-block-and-bleed (DBB) operation in a single compact module Conventional NPT and ANSI/ISA
Quick-Connects. QC, QF, QM, and QTM Series. No twisting, turning, or wrenching necessary. Single-end shutoff, double-end shutoff, and full-flow models
Quick-Connects QC, Q, QM, and QTM 1 www.swagelok.com Quick-Connects QC, Q, QM, and QTM No twisting, turning, or wrenching necessary Single-end shutoff, double-end shutoff, and full-flow models 2 Hose,
Rising Plug Valves. 4P and 5P Series. Roddable, straight-through orifice for maximum flow. Working pressures up to 6000 psig (413 bar)
Rising Plug Valves4P and 5P Series 1 www.swagelok.com Rising Plug Valves 4P and 5P Series Roddable, straight-through orifice for maximum flow Working pressures up to 6000 psig (413 bar) Packing below the
General Utility Service Needle Valves
General Utility Service Needle ValvesGU Series 1 www.swagelok.com General Utility Service Needle Valves GU Series Straight and angle patterns Stainless steel and carbon steel body material Pressures up
Bleed Valves and Purge Valves
Bleed Valves and Purge Valves 1 www.swagelok.com Bleed Valves and Purge Valves Bleed Valves Working pressures up to 10 000 psig (689 bar) Temperatures up to 850 F (454 C) 316 stainless steel, carbon steel,
VCR Metal Gasket Face Seal Fittings
lloy 2507 Super uplex Weld Fittings 1 www.swagelok.com Metal Gasket Face Seal Fittings WL 1/16 to 1 in. and 6 to 18 mm sizes High-purity stainless steels The original design, the authentic brand 2 Weld,,
Actuated Ball Valve Selection Guide
Actuated Ball Selection Guide, ISO 5211-Compliant Actuator Mounting s 1 www.swagelok.com Actuated Ball Selection Guide ISO 5211-Compliant Actuator Mounting s 40G, 40, 60, 83, H83, SK, and FKB s AFS Ball
Ultrahigh-Purity Fluoropolymer Diaphragm Valves
Ultrahigh-Purity Fluoropolymer Diaphragm s DRP Series 1 www.swagelok.com Ultrahigh-Purity Fluoropolymer Diaphragm s DRP Series Pneumatic and quarter-turn manual 2-way and 3-way models; pneumatic and manual
Diaphragm Valves. for Atomic Layer Deposition. Atomic Layer Deposition (ALD) Diaphragm Valves.
Diaphragm Valves for tomic Layer Deposition (LD) 1 www.swagelok.com Diaphragm Valves for tomic Layer Deposition LD DIPHRGM tomic Layer Deposition (LD) Diaphragm Valves Ultrahigh cycle life with high-speed
Bellows-Sealed Valves
Bellows-Sealed sb 1 www.swagelok.com Bellows-Sealed s B Working pressures up to 1000 psig (68.9 bar) Temperatures up to 900 F (482 C) 1/4, 3/8, 1/2, and 3/4 in.; 6, 10, and 12 mm end connections Brass,
Integral-Bonnet Needle Valves
Integral-Bonnet Needle ValvesO, 1, 18, 20, and 26 Series 1 www.swagelok.com Integral-Bonnet Needle Valves O, 1, 18, 20, and 26 Series Live-loaded packing system Compact design Working pressures up to 6000
Severe-Service Union-Bonnet Needle Valves
Severe-Service Union-Bonnet Needle ValvesN Series and HN Series 1 www.swagelok.com Severe-Service Union-Bonnet Needle Valves N Series and HN Series Working pressures up to 10 000 psig (689 bar) Temperatures
Swagelok Medium-Pressure, Gaugeable Tube Fit tings and Adapte r Fit tings
www.swagelok.com Swagelok Medium-Pressure, Gaugeable Fit tings and dapte r Fit tings For Pre s sure s up to 15 0 0 0 psig (1034 ba r) asy installation, no special tools required ssembly by one full turn
Instrument Manifold Systems
Manifold Systems 1 www.swagelok.com Manifold Systems, Direct, and Remote-Mount Manifolds and Modular Systems V, VB, and VL series 2-, 3-, and 5- instrument manifolds VE series 2-, 3-, and 5- direct-mount
Swagelok Ball Valve Actuation Options
Swagelok Ball Valve Actuation Options 1 www.swagelok.com Swagelok Ball Valve Actuation Options Rack and pinion pneumatic actuators, solenoid valves, and limit switches ISO 5211-compliant pneumatic actuators,
Trunnion Ball Valves. 83 Series and H83 Series. Working pressures up to psig (689 bar)
Trunnion Ball s83 Series and H83 Series 1 www.swagelok.com Trunnion Ball s 83 Series and H83 Series Working pressures up to 10 000 psig (689 bar) 1/8 to 1/2 in. and 6 to 12 mm Swagelok tube fitting or
PFA Needle Valves. 4RP Series
PFA Needle Valves 4RP Series High-purity PFA material Pressures up to 180 psig (12.4 bar) Temperatures up to 300 F (148 C) 1/4, 3/8, and 1/2 in. Swagelok PFA tube fitting end connections www.swagelok.com
Stream Selector System For Process Analyzer Applications
www.swagelok.com Selector System For Process Analyzer Applications SSV Series Provides double-block-and-bleed (DBB) operation in a single compact module Conventional NPT and ANSI/ISA 76.00.02 compatible
Gaugeable Alloy 400 Mechanically Attached Pipe and Tube Fittings
www.swagelok.com Gaugeable Alloy 400 Mechanically Attached and Fittings For use with MIL-T-16420K 70/30 and 90/10 copper-nickel tubing and pipe Excellent corrosion resistance in chloride-containing environments
Stream Selector System
www.swagelok.com Selector System For Process Analyzer Applications SSV Series Provides double-block-and-bleed (DBB) operation in a single compact module Conventional NPT and ANSI/ISA 76.00.02 compatible
ISO 5211-Compliant Actuators for Swagelok Ball Valves
www.swagelok.com ISO 5211-Compliant s for Swagelok Ball s 40G, 40, 60, and 83 ; and AFS Ball s Pneumatic rack and pinion actuators s meet industry standards for interface: ISO 5211, NAMUR, and VDI/VDE
S, M, L, and 31 Series. Straight-pattern flow coefficients (C v ) from to Low- and high-pressure service
www.swagelok.com Metering Valves S, M, L, and Straight-pattern flow coefficients (C v ) from 0.004 to 0.16 Low- and high-pressure service Repeatable vernier handles available rass and 316 stainless steel
Diaphragm Valves. LD Series. Working pressures up to 300 psig (20.6 bar) Shutoff, bulk-gas distribution, and isolation service
www.swagelok.com Diaphragm Valves LD Series Working pressures up to 300 psig (20.6 bar) Shutoff, bulk-gas distribution, and isolation service Cast, forged, and bar stock stainless steel body material 1/4
SSV Series. Assembly and Service Instructions. Contents. Tool Requirements
SSV Series Assembly and Service Instructions Contents Tool Requirements................. 1 Components and Hardware.......... 2 Port and Mounting Dimensions....... 3 General SSV Assembly.............. 4
Special Alloy Ball Valves
www.swagelok.com Special Alloy Ball Valves 60 Series 3/8 to 1 in. sizes Alloy 625, alloy 825, alloy 2507 super duplex stainless steel, and 6-moly materials On-off (2-way) valves Compensating seat design
Check Valves. C, CA, CH, CP, and CPA Series. Working pressures up to 6000 psig (413 bar) Adjustable and fixed cracking pressures
www.swagelok.com Check Valves C, CA, CH, CP, and CPA Series Working pressures up to 6000 psig (413 bar) Adjustable and fixed cracking pressures Variety of end connections 316 stainless steel and brass
Gaugeable Tube Fittings and Adapter Fittings
www.swagelok.com Gaugeable Fittings and dapter Fittings vailable in tube sizes from / to 2 and 2 to 50 mm Consistent gaugeability upon initial installation asy to disconnect and retighten Wide variety
Gaugeable Tube Fittings and Adapter Fittings
www.swagelok.com Gaugeable Fittings and dapter Fittings vailable in tube sizes from / to 2 and 2 to 50 mm Consistent gaugeability upon initial installation asy to disconnect and retighten Wide variety
Be llows-se aled Valve s
www.swagelok.com Be llows-se aled Valve s U Secondary containment system above the bellows Working pressures up to 2500 psig (172 bar) Temperatures up to 1200 F (648 C) 1/4, 3/8, 1/2, 3/4, and 1 in.; 6,
High-Pressure Needle Valves
www.swagelok.com High-Pressure Needle Valves Working pressures up to 4 000 psig (3100 bar) Temperatures up to 40 F (232 C) Weep holes for leak detection Packing below stem threads Nonrotating stem design
DA Series Diaphragm Valve
DA Series Diaphragm Valve Service Instructions Pneumatically Actuated Valve Toggle Valve Valve Valve Valves are shown with tube butt weld ends. These instructions also apply to DA series valves with any
Quick-Connects. QC, QF, QM, and QTM Series. No twisting, turning, or wrenching necessary
www.swagelok.com Quick-Connects QC, Q, QM, and QTM No twisting, turning, or wrenching necessary Single-end shutoff, double-end shutoff, and full-flow models 2 Quick-Connects Contents Instrumentation Quick-Connects
DL/DS Series Diaphragm Valve
DL/DS Series Diaphragm Valve Service Instructions DL Series (Lever Handle) Valve DS Series (Round Handle) Valve Valves are shown with tube butt weld ends. These instructions also apply to DL or DS series
VCR. Metal Gasket Face Seal Fittings. 1/16 to 1 in. and 6 to 18 mm sizes. High-purity stainless steels
www.swagelok.com Metal asket ace Seal ittings /6 to and 6 to 8 mm sizes igh-purity stainless steels The original design, the authentic brand 2 Metal asket ace Seal ittings ontents lands Page 4 odies Page
Pipe Fittings 1/16 to 1 in. sizes 316 stainless steel, brass, and carbon steel NPT, ISO/BSP, and SAE threads
www.swagelok.com Pipe Fittings 1/16 to 1 sizes 316 stainless steel, brass, and carbon steel, /SP, and S threads 2 Pipe Fittings Contents Nipples Page 4 dapters, Gaskets Page 6 Reducing ushings, Reducers
Bellows-Sealed Valves
www.swagelok.com ellows-sealed Valves Working pressures up to 1000 psig (68.9 bar) Temperatures up to 900 F (482 C) 1/4, 3/8, 1/2, and 3/4 in.; 6, 10, and 12 mm end connections rass, stainless steel, and
D iaphragm Valve s. for Atomic L aye r D e position. Atomic Layer Deposition (ALD) Diaphragm Valves.
www.swagelok.com D iaphragm Valve s for tomic L aye r D e position tomic Layer Deposition (LD) Diaphragm Valves Ultrahigh cycle life with high-speed actuation C v range from 0.27 to 0.62 Up to 392 F (200
Be llows-se aled Valve s
www.swagelok.com Be llows-se aled Valve s BN Series Packless valves with all-metal seal to atmosphere Working pressures up to 500 psig (34.4 bar) Temperatures up to 200 F (93 C) 1/4 to 1/2 in. and 6 to
Be llows-se aled Valve s
www.swagelok.com Be llows-se aled s B Working pressures up to 1000 psig (68.9 bar) Temperatures up to 900 F (482 C) 1/4, 3/8, 1/2, and 3/4 in.; 6, 10, and 12 mm end connections Brass, stainless steel,
KHR Series Regulators
KHR Series Regulators Maintenance Instructions Kit Contents retainer Poppet Poppet spring Poppet damper Outer body seal Inner body seal Upper piston seal seal backup ring Main piston seal vent seal Self-vent
Medium- and High-Pressure Fittings, Tubing, Valves, and Accessories
Medium- and High- Fittings, Tubing, Valves, and ccessories 1 www.swagelok.com www.swagelok.com Medium- and High- Fittings, Tubing, Valves, and ccessories FK, FKB, IPT, CTB, and Sno-Trik Series Products
DR Series Radial Diaphragm Valves
DR Series Radial Valves Service Instructions Valves with Plastic Actuators (1/2 through 1 inch) Valves with Aluminum Actuators (1/2 through 2 inch) Manual model Pneumatic model Manual model Pneumatic model
Modular Instrumentation System
www.swagelok.com Modular nstrumentation System Kenmac Series Modular 85 System Provides a standard modular instrumentation interface and mounting system: 2- and 4- valve pressure and differential pressure
Toggle Valve s. OG, 1G, and 92 Series. Manual and pneumatically actuated models. Straight, angle, and cross body patterns
www.swagelok.com Toggle Valve s OG,, and 92 Series Manual and pneumatically actuated models Straight, angle, and cross body patterns 316 SS and brass body materials Features Compact, rugged design Opens
Medium- and High-Pressure Fittings, Tubing, Valves, and Accessories
www.swagelok.com Medium- and High- Fittings, Tubing, Valves, and ccessories FK, FKB, IPT, and Sno-Trik Series Products Rated up to 60 000 psig (4134 bar) nd connections up to 1 1/2 and 12 mm NC MR0175/ISO15156
Instrument Manifolds. V, VB, and VL Series. 2-, 3-, and 5-valve instrument manifolds
www.swagelok.com Manifolds V, VB, and VL Series 2-, 3-, and 5- instrument manifolds All 316 stainless steel construction with PTFE packing Working pressures up to 6000 psig (413 bar) Temperatures up to
Ultrahigh-Purity Fluoropolymer Diaphragm Valves
www.swagelok.com Ultrahigh-Purity Fluoropolymer Diaphragm s DRP Series DuPont Teflon modified PTFE wetted parts and polypropylene actuator Meet SEMI Standard F57-0301 for ultrahigh-purity system components
Weir-Style Diaphragm Valves
www.swagelok.com Weir-Style Diaphragm s GSI Series Available in sizes 1/2 to 4 Available with a variety of end connections, including Kwik-Clamp and TS series sanitary clamp and tube butt weld 2 Weir-Style
Multihead Hydraulic Swaging Unit (MHSU) Setup and Operating Instructions
Multihead Hydraulic Swaging Unit (MHSU) Setup and Operating Instructions Up to 1 in./25 mm MHSU with base 1 in./25 mm and over MHSU with base (also for use with 5/8 and 3/4 in. SAF 2507 TM super duplex
Swagelok Alternative Fuel Ser vice (AFS) Ball Valves
www.swagelok.com Swagelok Alternative Fuel Ser vice (AFS) Ball Valves For High-Pressure, High-Flow Applications Swagelok AFS Ball Valves Working pressures up to 6000 psig (413 bar) Flow coefficients (C
Medium-Pressure Ball Valves
www.swagelok.com Medium-Pressure Ball Valves FKB Series Innovative stem seal design (patent-pending): maintains full pressure rating throughout the entire operating temperature range Bottom-loaded stem
Weir-Style Diaphragm Valves
www.swagelok.com Weir-Style Diaphragm s DW Series Standard valve sizes 1/2 to 4 in. and minivalve sizes 1/4, 3/8, and Manual and pneumatic actuation Kwik-Clamp, TS series sanitary clamp, and tube butt
Medium-Pressure Ball Valves
www.swagelok.com Medium-Pressure Ball Valves FKB Series Innovative stem and end connection seal design (patent-pending): maintains full pressure rating throughout the entire operating temperature range
Gaugeable Tube Fittings and Adapter Fittings
Gaugeable Fittings and dapter Fittings www.swagelok.com Gaugeable Fittings and dapter Fittings TUB vailable in tube sizes from / to 2 and 2 to 50 mm Consistent gaugeability upon initial installation asy
Springless Diaphragm Valves
www.swagelok.com Springless Diaphragm Valves for igh Performance DP Series Suitable for ultrahigh-purity applications 316L VIM-VAR stainless steel body Low-pressure and high-pressure models VCR, tube butt
Tr unnion Ball Valve s
www.swagelok.com Tr unnion Ball Valve s 83 Series and H83 Series Working pressures up to 10 000 psig (689 bar) 1/8 to 1/2 in. and 6 to 12 mm Swagelok tube fitting or NPT end connections 316 stainless steel
INSTRUMENTATION. Tube Fittings. Catalog Number 01-5 November,
INSTRUMNTATION Tube Fittings Catalog Number 0-5 November, 009 www.dklok.com Index Union U Tube to Tube Union Thermocouple Connector MCT Tube to Female Pipe Female Connector CF-N 9,40 Union lbow Union Tee
Figure 1: HB Series Ball Valve Cross Sectional View DISASSEMBLY WARNING: MAKE CERTAIN THE SYSTEM IN WHICH THE VALVE IS INSTALLLED IS EXHAUSTED OF ALL
Maintenance Instructions MI-142 Revision - HB Series Ball Valve MAXIMUM ALLOWABLE WORKING PRESSURES Table 1 Maximum Allowable Working Pressure versus Seat Material Seat Stainless Steel Material Body Material
Gaugeable Tube Fittings and Adapter Fittings
www.swagelok.com Gaugeable ittings and dapter ittings vailable in tube sizes from / to 2 in. and 2 to 50 mm Consistent gaugeability upon initial make-up asy to disconnect and retighten Wide variety of
VCR Metal Gasket Face Seal Fittings
VR Metal Gasket ace Seal ittings 1/8 to 1 and 6 to 18 mm sizes high-purity stainless steels www.swagelok.com VR Metal Gasket ace Seal ittings Index General Information Glands ages 4, 5, 6 odies ages 6,
Locked Bonnet Needle Valves
Locked Bonnet Needle Valves Series Working Pressures up to 6000 psig (413 bar) Temperature Range from -65 to 1200 F (- 53 C to 648 C) Flow Coefficients up to 2.18 Locked bonnet eliminates accidental disassembly
Medium-Pressure Ball Valves
www.swagelok.com Medium-Pressure Ball Valves FKB Series Innovative stem and end connection seal design (patent-pending): maintains full pressure rating throughout the entire operating temperature range
Instrument Ball Valves
www.swagelok.com Instrument all s 40 Series On-off, switching, and crossover flow paths Working pressures up to 3000 psig (206 bar) Temperatures from 50 to 150 (10 to 65 ) Low-temperature service option
ball valves ball valves 7 Series Fire Safe 2-way, 3-piece Bolted Ball Valves
7 Series Fire Safe 2-way, 3-piece Bolted Ball Valves HOKE s 7 Series Fire Safe Valves meet demanding application requirements in the production environment of chemical and petrochemical processing facilities.
Certificate of Type Approval (RQS)
Date Issued: 18/OCT/2000 Certificate Number: 00-C15300-X Certificate of Type Approval (RQS) This is to certify that Swagelok Company has met the requirements of ABS Product Type Approval for Swagelok Tube
Tool Reference Guide. Swagelok Minnesota North Dakota Appleton offers a complete line of tools and equipment to rent or purchase.
Tool Reference Guide Swagelok Minnesota North Dakota Appleton offers a complete line of tools and equipment to rent or purchase. This allows for ease and accessibility while in the work place. Whether
Calibration and Switching Module. User s Manual. A Swagelok Pre-Engineered. Subsystem. Pre-engineered subsystems available in weeks, not months.
Calibration and Switching Module User s Manual A Swagelok Pre-Engineered Subsystem Pre-engineered subsystems available in weeks, not months. Field-tested design ensures optimum system performance. Contents
Stainless Steel Valves
www.swagelok.com Stainless Steel Valves For the Sanitar y Industries Sanitary ball valves Manual and pneumatically actuated butterfly valves Disk and ball check valves ir blow check valves ir relief valves
Process Ball Valve Handle O ptions
www.swagelok.com Process Ball Handle O ptions Ha ndle K its a nd Factor y-installe d Ha ndle s Lever and oval handles Locking brackets for lever and oval handles Oval latch-lock handles Process Ball Handle
Instructions for Installation, Operation, Care and Maintenance
Bulletin 407 Rev. T Model E Alarm Check Valve Bulletin 407 Rev. T Instructions for Installation, Operation, Care and Maintenance 4 (100 mm), 6 (150 mm), 8 (200 mm) Sizes With Model E3 Trim Listed by Underwriters
DP Series Diaphragm Valve Installation and Maintenance Instructions
DP Series Diaphragm Valve Installation and Maintenance Instructions Contents Installation Actuation Actuator Orientation Welding Testing Maintenance Kit Contents Tool Requirements Exploded View Replacing
Bleed Valves and Purge Valves
www.swagelok.com Bleed Valves and Purge Valves Bleed Valves Pressures up to psig (689 bar) Temperatures up to 8 F ( C) 36 stainless steel, carbon steel, or alloy R- materials Purge Valves Pressures up
A Quick Look at Fluid System Solutions. swagelok.com
A Quick Look at Fluid System Solutions swagelok.com Who We Are Swagelok Company is a major developer and provider of fluid system solutions, including products, assemblies, and services for the research,
Quicklub Lubrication Systems
Fittings, Adapters and Accessories Divider Valve Mounting Accessories 246416 Valve mounting bracket 51304 ¼" nylon locknut for valve mounting 247023 Grade 8, ¼" valve mounting bolt 239499 Template for
Quicklub Lubrication Systems Fittings, Adapters and Accessories
Divider Valve Mounting Accessories 24646 Valve mounting bracket 5304 4" nylon locknut for valve mounting 247023 Grade 8, 4" valve mounting bolt 239499 Template for divider valve mounting (6, 8, 0 and 2
Field Service Bulletin CNG and LNG Leak Repair Tutorial
Field Service Bulletin CNG and LNG Leak Repair Tutorial ENP-552 Rev. A: July 26, 2017 1. Introduction Figure 1 Leak detection for CNG (left) is the same as LNG (right). Leak detection and repair is one
Quicklub Lubrication Systems Fittings, Adapters and Accessories
Divider Valve Mounting Accessories 246416 Valve mounting bracket 51304 ¼" nylon locknut for valve mounting 247023 Grade 8, ¼" valve mounting bolt 239499 Template for divider valve mounting (6, 8, 10 and
AV-430. Application. Features. Applicable Literature. Valve Linkage for Pneumatic Actuators General Instructions
AV-430 Valve Linkage for Pneumatic s General Instructions Application The AV-430 valve linkage is used to field assemble MK-66X1, MK-68X1, and MK-6911 actuators, as well as the obsolete MK-47X1 actuators,
Product warranty. Quality Policy. The Goal
About the Company SEALEXCEL (INDIA) PVT. LTD. is a fast growing manufacturing company in the field of design, development, production and marketing of high quality valves and fittings for international
SCREWED BONNET NEEDLE VALVES
SCREWED BONNET NEEDLE VALVES H-99 SERIES FEATURES n Blowout-Proof Stem n MAWP* up to 1, psi (69 bar) n MAWT* up to 648 C (12 F) n End connection size range: to 1" or to 25mm n Flow Coefficient (Cv) to1.5
Fluid Distribution Header
Fluid Distribution Header Application Guide A Pre-Engineered Subsystem Pre-engineered subsystems available in weeks, not months. Field-tested design ensures optimum system performance. Versatile manifold
Sample Probe Module. Application Guide
Sample Probe Module Application Guide A Swagelok Pre-Engineered Subsystem Pre-engineered subsystems available in weeks, not months. Field-tested design ensures optimum system performance. Wide range of
An Installer s Pocket Guide for Swagelok Tube Fittings
www.swagelok.com An Installer s Pocket Guide for Swagelok Fittings 2 CONTENTS Intermixing/Interchanging... 8 Metric Swagelok Fittings... 8 Installation Instructions Safety Precautions... 9 Up to /25 mm
DIT VALVE ASSEMBLY PARTS CATALOG
PARTS CATALOG Revision B October 4, 2004 THIS PAGE LEFT BLANK INTENTIONALLY 2 WARNING AFTER REPLACEMENT OF ANY PART IN THIS DEVICE, THE OPERATION OF THE DEVICE MUST PASS TESTS PRESCRIBED IN THE LATEST
Swagelok Ball Valve Actuation Options
www.swagelok.com Swagelok Ball Valve Actuation Options Rack and pinion pneumatic actuators, solenoid valves, and limit switches ISO 5211-compliant pneumatic actuators, solenoid valves, limit switches,
High Pressure Ball Valves
High Pressure Ball Valves 79 Valve Options Reliable, simple, operation for on-off service Fast acting, one quarter turn fully opens or closes the valve Maximum performance, straight through flow for minimum
THE PREMIUM QUALITY. Hydraulic Swaging Unit for Pre-Swaging Over 1. Catalog Number 01-5 March, 2009 HYDRAULICSWAGINGUNIT.
TH PRMIUM QUAITY Catalog Number 0-5 March, 009 HYRAUICSWAGINGUNIT.HS-A Hydraulic Swaging Unit for Pre-Swaging Over www.dklok.com Index Union U Tube to Tube Union Thermocouple Connector MCT Tube to Female