CATALOG

Transcription

1 CATALOG

2 The Advantages of TM10 HST Machines Produced by DST-URAL Contents 1 Modern industrial engineering at DST-URAL Plant Direct engineering documentation transfer to the automated industrial equipment Usage of modern lathes, including welding machines (KAWASAKI, MOTOMAN, ABB) that are used for the first time at Russian tractor manufacturing plants. Quality Control Department, Pre-Delivery Inspection, Service, Claim Procedure are all in one. This helps to have short feedback to the Production. DST-URAL Plant... 2 Advantages of TM10 HST of DST-URAL... 4 TM10 HST9 Bulldozer... 8 TM10 HST10 Bulldozer TM10 HST12 Bulldozer TM10 HST15 Bulldozer TM10 HST20 Bulldozer Pipe Layer Machines Cable Layer Machines Self-Propelled Welding Machine TM10.00B HST9 MTO1 Crawler Tractor DST-URAL Products «DST-URAL» Plant is a modern plant for producing bulldozers and special machines on the chassis of a crawler 2 3

3 2 3 Hydrostatic Power Bosch- Rexroth, DANFOSS, Linde Hydraulics The transmission consists of six elements: 4 hydraulic (pump motors), 2 on-board gearboxes. Maximal traction through all the operation range Maneuverability is ensured by stepless speed and direction change, including pivot turn with 100% of traction The hydraulic system and on-board planetary gearboxes are protected from overloads by maximal pressure and temperature breakers All the transmission is completely tight. The controller is in protective case, thus it is protected from water and mud. In contrast to hydro-mechanical and mechanical transmissions HST can be submerged, and the tank should just be washed afterwards. Hexagonal Cab, Automation Improved visibility of blade edges Travel and implement control with joysticks Twindow insulation and efficient cab heater ROPS/FOPS protective systems; grates, Fleko protection from the trees, AC, etc. On-board navigation controller recording all the key operation parameters in the black box is installed 4 Full-length truck protection 4 5 Engine 5 Hydraulic pump 6 TM10 Maintainability The largest dealer and service network on the territory of Russia and CIS countries, mobile service teams at the manufacturer s plant YMZ 236, 238, 536, 652 engines are the most large-scale diesel engine for special machines in the Russian Federation. 95% of the undercarriage is standardized with B10 (T170), B11, B12, D85, D155, SD32. Popular elements of the undercarriage: the track with a closed joint, track rollers on journals and idlers, track adjuster. Top manufacturer devices in combination with protective breakers are used in the hydrostatic power transmissions. They are always in stock in Moscow, Chelyabinsk, Khabarovsk. They are mostly used in special machines (excavators). HST Scheme the Simplest The reliability is improved due to less number of transmission elements and no turning friction coupling. HST pump operation is max 75% of maximal rpm. The performance factor is 75-80% depending on the operation mode (more than for hydro-mechanical transmission: ~70%) Improved roadability thanks to constant traction on each side, up to track counter travel. Traction is maintained at turns. Hydraulic motor Planetary triple reduction on-board gearbox Undercarriage Simple structure On-board gearboxes are independent from the crawler truck Universal for all environments and operations: abrasive media, quarries, road construction.

4 New TM10 bulldozer with YMZ engine and mechanical transmission analogous to B10 (ChTZ-URALTRAC) was patented. The tests were carried out in the Republic of Belarus; basing on the test results the Belarus Ministry of Transport recommended the bulldozer as the optimal solution in terms of technical and economic parameters. A new TM10 bulldozer with hydrostatic power transmission (Bosch-Rexroth HST) was commercialized. The selection of such HST is explained by successful utilization of this transmission by the leading manufacturers: Liebherr, CAT, Komatsu, John Deere, CHETRA. The main units are welded with KAWASAKI and MOTOMAN. TM10 HST9 Bosch-Rexroth (Germany) bulldozer was commercialized, with m up to 18 t. Large-scale universal machine. The Plant represented by DST- URAL Ltd. was listed as one of the largest manufacturers of building machines in Russia Heavy quarry bulldozer TM10 HST20 (weight is t) was manufactured From DST-URAL Plant has been manufacturing certified roadbuilding machinery: the main machine is own-produced TM10 bulldozer with YMZ, Cummins, Deutz engines. TM10 was modernized: control joysticks, on-board computer, and polymeric paint were introduced. Dealer and service centers were established in Russia and CIS countries. Thanks to usage of Bosch-Rexroth hydrostatic power transmission TM10 came very close to world-known manufacturers in terms of productivity, efficiency and reliability. Total plant output was more than 150 special machines per year. Implementation of high-efficient welding robots to weld the frame for one cycle, a separate precise robotic welding shop with total area of sq.m was organized. Prospective assessment of constructing a new Plant having the capacity of special crawler machines per month. 6 7

5 8 9

6 Bulldozer TM10 HST9 Undercarriage Frame Track rollers Number of track rollers Track chain Track shoe width Track shoe grouser Bearing area Track adjuster linear load-bearing structure made of HSS steel, high welding accuracy lifetime lubricated, on sliding bearings (journals) 6 bottom rollers + side sprocket/ 2 carrier rollers on each side 42 track shoes 500 mm 65 mm 2.86 m2 hydraulic On-board gearboxes Control Brake system hydrostatic with electronic control hydraulic pump coupled with hydraulic motor with stepless transmission shift planetary (PMP, Italy) electric and hydraulic servo hydraulic (pilot-operated check valve), normally closed multiple-disc clutches Power, hp 180, t 17,5 Engine YMZ-236 Power, kw/hp 132/180 Implement Control Operating volume 11,15 l hydraulic, separate for each device Blade volume, m3 5,0 Traction, t 23 Generator 24V/55A Storage battery 2*12V 2*132Ah Pre-heating with autonomous 14TC-10 Teplostar heating function Hydraulic pump Control valve Filtration Hydrosila NSh-100 Output: 200 l/min Max pressure: 20 MPa sectional (Belarus) double filtration: at suction, full-flow at discharge 10 11

7 Cab and Control Cab Seat Safety Travel and attachable implement control hexagonal, improved visibility, with springs, twindow insulation, climate control system (heating and ventilation), cab air circulation, enlarged cab filter, circulation air filter, windscreen, rear window and door window wipers and washers, sun blind ergonomic, with springs, two-point seat belt, seat switch ROPS/FOPS, open door fixation 4-position joysticks Bulldozer TM10 HST10 Filling Values Cooling system Fuel tank Engine lubrication system 50 l 320 l 29 l and implement hydraulic system 200 l Traction force, kn ,0 4,0 6,0 8,0 10,0 12,0 Speed, km/h Parameters under Load Speed limit at 2100 rpm, forward 11 km/h backward 11 Power, hp Blade volume, m3 5,0, t Traction, t Engine YMZ-236/238 Power, kw/hp 132/180 Operating volume l Generator 24V/55A Storage battery 2*12V/ 2*132Ah Pre-heating with 14TC-10 Teplostar autonomous heating function 12 13

8 Undercarriage Cab and Control Frame Track rollers linear load-bearing structure made of HSS steel, high welding accuracy lifetime lubricated, on sliding bearings (journals) Cab hexagonal, improved visibility, with springs, twindow insulation, climate control system (heating and ventilation), cab air circulation, enlarged cab filter, circulation air filter, windscreen, rear window and door window wipers and washers, sun blind Number of track rollers 6 bottom rollers + side sprocket/ 2 carrier rollers on each side Seat ergonomic, with springs, two-point seat belt, seat switch Track chain Track shoe width Track shoe grouser Bearing area 42 track shoes on each side 500 mm 65 mm m2 Safety Travel and attachable implement control ROPS/FOPS, open door fixation 4-position joysticks Track adjuster hydraulic Filling Values Cooling system 50 l On-board gearboxes hydrostatic with electronic control hydraulic pump coupled with hydraulic motor with stepless transmission shift planetary (PMP, Italy) Fuel tank Engine lubrication system and implement hydraulic system 320 l 29 l 200 l Control electric and hydraulic servo Brake system hydraulic (pilot-operated check valve), normally closed multiple-disc clutches Implement Control hydraulic, separate for each device Hydraulic pump Hydrosila NSh-100 Output: 200 l/min Max pressure: 20 MPa Control valve sectional (Belarus) Filtration double filtration: at suction, full-flow at discharge Traction force, kn ,0 4,0 6,0 8,0 10,0 12,0 Speed, km/h Parameters under Load Speed limit at 2100 rpm, forward-11 km/h backward

9 Bulldozer TM10 HST12 Undercarriage Frame Track rollers Number of track rollers Track chain Track shoe width Track shoe grouser Bearing area Track adjuster linear load-bearing structure made of HSS steel, high welding accuracy lifetime lubricated, on sliding bearings (journals) 7 bottom rollers on each side/ 2 carrier rollers on each side 45 track shoes on each side 500 mm 65 mm 3.15 m2 hydraulic On-board gearboxes Control hydrostatic with electronic traction control. Speed shift under load, full-time all-track drive including counter travel of pivot turn hydraulic pump coupled with hydraulic motor with stepless transmission shift. planetary (PMP, Italy) electric and hydraulic servo Power, hp 240, t 21 Engine YMZ-536; 6-cylinder, 4-stroke, in-line, with direct fuel injection, turbocharged, water-cooled with supercharged air intercooler of the airto-air type installed on the vehicles Brake system hydraulic (pilot-operated check valve), normally closed multiple-disc clutches Implement Control Blade volume, m3 5,0 Traction, t 28 Power, kw/hp at nominal rpm Operating volume Generator Storage battery 176,5/240 6,65 l AC, 24V, 100A, with installed voltage regulator 2*12V/ 2*132Ah Hydraulic pump Control valve Filtration hydraulic, separate for each device Hydrosila NSh-100 Output: 200 l/min Max pressure: 20 MPa sectional (Belarus) double filtration: at suction, full-flow at discharge Starting device electric starter, 24V nominal voltage, 4 kw nominal power 16 17

10 Cab and Control Cab Seat Safety Travel and attachable implement control hexagonal, improved visibility, with springs, twindow insulation, climate control system (heating and ventilation), cab air circulation, enlarged cab filter, circulation air filter, windscreen, rear window and door window wipers and washers, sun blind ergonomic, with springs, two-point seat belt, seat switch ROPS/FOPS, open door fixation 4-position joysticks Filling Values Cooling system Fuel tank Engine lubrication system and implement hydraulic system 60 l 320 l 29 l 200 l Traction force, kn Parameters under Load Speed limit at 2100 rpm, forward 11 km/h backward ,0 4,0 6,0 8,0 10,0 12,0 Speed, km/h 18 19

11 Bulldozer TM10 HST15 Undercarriage Frame Track rollers Number of track rollers Track chain Track shoe width Track shoe grouser Bearing area Track adjuster linear load-bearing structure made of HSS steel, high welding accuracy lifetime lubricated, on sliding bearings (journals) 7 bottom rollers on each side/ 2 carrier rollers on each side 41 track shoes on each side 560 mm 80 mm 3.93 m2 hydraulic On-board gearboxes Control Brake system hydrostatic with electronic control hydraulic pump coupled with hydraulic motor with stepless transmission shift. planetary (PMP, Italy) electric and hydraulic servo hydraulic (pilot-operated check valve), normally closed multiple-disc clutches Power, hp 300, t 26 Engine YMZ-238 (turbocharged) Power, kw/hp 242/330 Implement Control Operating volume 14,86 l hydraulic, separate for each device Blade volume, m3 8,7 Traction, t 40 Generator Storage battery Pre-heating with autonomous heating function 24V/55A 2*12V/ 2*132Ah 14TC-10 Teplostar Hydraulic pump Control valve Filtration Hydrosila NSh-100 Output: 200 l/min Max pressure: 20 MPa sectional (Belarus) double filtration: at suction, full-flow at discharge 20 21

12 Cab and Control Cab Seat Safety Travel and attachable implement control hexagonal, improved visibility, with springs, twindow insulation, climate control system (heating and ventilation), cab air circulation, enlarged cab filter, circulation air filter, windscreen, rear window and door window wipers and washers, sun blind ergonomic, with springs, two-point seat belt, seat switch ROPS/FOPS, open door fixation 4-position joysticks Bulldozer TM10 HST20 Filling Values Cooling system Fuel tank 60 l 390 l Engine lubrication system 29 l and implement hydraulic system 200 l Traction force, kn Parameters under Load Speed limit at 2100 rpm, km/h forward 11 backward 11 Power, hp 412, t 38,5 Engine YMZ-652, turbocharged Power, kw/hp 303/ Operating volume 11,12 l ,0 4,0 6,0 8,0 10,0 12,0 Speed, km/h Blade volume, m3 10 Traction, t 51 Generator Storage battery Pre-heating autonomous function with heating 24V/55A 2*12V/ 2*132Ah Webasto Thermo E

13 Undercarriage Cab and Control linear, three-point support of crawler trucks with equalizer beam Cab hexagonal, improved visibility, with springs, twindow insulation, climate Frame load-bearing structure made of HSS steel, high welding accuracy control system (heating and ventilation), cab air circulation, enlarged cab filter, circulation air filter, windscreen, rear window and door window wipers Track rollers lifetime lubricated, on sliding bearings (journals) and washers, sun blind Number of track rollers 7 bottom rollers + side sprocket / 2 carrier rollers on each side Seat ergonomic, with springs, two-point seat belt, seat switch Track chain Track shoe width Track shoe grouser Bearing area 41 track shoes 560 mm 80 mm 3.93 m2 Safety Travel and attachable implement control ROPS/FOPS, open door fixation 4-position joysticks Track adjuster hydraulic Filling Values Cooling system Fuel tank 80 l 680 l hydrostatic with electronic control Engine lubrication system 35 l hydraulic pump coupled with hydraulic motor with stepless transmission shift and implement hydraulic system 200 l On-board gearboxes planetary (PMP, Italy) Control electric and hydraulic servo Brake system hydraulic (pilot-operated check valve), normally closed multiple-disc clutches Implement Control hydraulic, separate for each device Hydraulic pump Hydrosila NSh-100 Output: 200 l/min Max pressure: 20 MPa Control valve sectional (Belarus) Traction force, kn Parameters under Load Speed limit at 2100 rpm, forward 11 km/h backward 11 Filtration double filtration: at suction, full-flow at discharge 0 2,0 4,0 6,0 8,0 10,0 12,0 Speed, km/h 24 25

14 26 27

15 Modern Pipe Laying Machines On TM10B2 HST chassis TO HST, TG HST, TG HST, TG HST 1 2 Use 3 Hydraulic Planetary (BDF) Boom and Hook Winches Planetary winches (PMP, Italy) with hydraulic drive (Danfoss or analogous) Hydro motor lifetime is max motor hours Planetary winch mechanism with normally closed multiple-disc clutches. Automatic hook release is an option. of Modern HST Provides perfect maneuverability up to pivot turn Ensures high reliability Speed shift from 0 km/h to 10 km/h is stepless and smooth The Engine from a Basic Tractor: YMZ-238 or Cummins 8.3 (6.7) Reserve power (240 hp) ensures operation at nominal rating enhancing the lifetime (>10000 motor hours) Hexagonal Cab with Ergonomic Operator s Seat Provides 360 vision in horizontal plane and 120 in vertical plane, thanks to the sunroof the operator can control the cargo in any location Hosting equipment is controlled with joysticks; it allows changing the boom reach and regulating hook lift simultaneously. Turn control with a joystick when moving AZK-110 to prevent overloads and tip over when hoisting a cargo, to protect when working in the area of power transmission lines, information on the cargo weight being hoisted, max load capacity, boom reach, boom angle Perfect Maneuverability Precise operator s message to both track chains allowing pivoting the machine with max load. This can be used to facilitate turning and moving aside a heavy pipe Construction Features of Rigid Undercarriage and Configuration Crawler trucks are rigidly connected making a single structure with the frame through bolt joins The frame allows maintaining the undercarriage and on-board gearboxes without dismantling them from the hoisting devices Offset axis of boom fixation allows lifting the boom vertically Solid even armored bottom improves flotation on timberland and weak soil V8 scheme without a turbine has no traction turbo lag in the range of rpm. Ensures the state of equilibrium with minimal vibration Generator for elevated current (55A) provides lighting and charging when idling. Reliable Cummins 8.3 or Cummins 6.7 is standardized with KAMAZ

16 Pipe Layer Machines TO HST TG HST т 15 Load capacity of TO12 Calculated load capacity Undercarriage Frame Track rollers Number of track rollers rigid, four-point load-bearing structure made of HSS steel, high welding accuracy lifetime lubricated, on sliding bearings (journals) 7 bottom rollers on each side / 2 carrier rollers on each side Engine Power, kw/hp 132/ /240 YMZ-236/YMZ-238 Load capacity, t 10 ПБ Operation range according to Industrial Safety Rules Boom reach relative to tip over rib, m Track chain Track shoe width Track shoe grouser Track adjuster 45 reinforced track shoes on each side 900 mm 65 mm hydraulic Min rated consumption, g/kw (g/hp) 214 (157) 202 (150) 65 Load capacity of ТG20 Operator s Seat. Travel Control 60 Operating volume l / l Cab hexagonal, improved visibility, twindow insulation, with springs Torque / torque backup / reserve power Electric starter Generator 667 Nm at rpm 883 Nm at rpm St / 8.1 kw 24V/55A т Calculated load capacity ПБ Safety Seat Travel and attachable implement control emergency hatch, FOPS, outer battery compartment ergonomic, with seat belt 4-position joysticks Storage battery Pre-heating with autonomous heating function 2*12V/ 2*132Ah 14TC-10 Teplostar Load capacity, t Operation range according to 5 Industrial Safety Rules Boom reach relative to tip over rib, m On-board gearboxes Control Brake system Hydrostatic Power Bosch-Rexroth, DANFOSS, Linde Hydraulics hydraulic pump coupled with hydraulic motor with stepless transmission shift. planetary (Italy) electric and hydraulic servo hydraulic (pilot-operated check valve), normally closed multiple-disc clutches 30 31

17 Pipe Layer Equipment The values in brackets are given for 9m boom Hook is actuated through a sheave system with a winch Pipe Layer Machines TG HST Hoisting height: Hook lowering height Hoisting/ lowering speed Counterweight is built of 2 plates Winch Nominal load capacity at 2.5 m boom reach Max calculated load capacity 5.9 (7.9) m 2.5 m from m/sec to m/sec non-detachable, weight is 4000 kg double-drum with hydraulic drive 12t / 20 t 25 t/ 40 t Engine YMZ-238 (turbocharged) Power, kw/hp 242/330 Min rated consumption, g/kw (g/hp) 214 (157) Operating volume l Torque / torque 1180 Nm at rpm backup / reserve power Electric starter St / 8.1 kw Filling Values Attachable Implement Control System Generator Storage battery 24V/80A 2*12V/ 380 Ah Cooling system 60 l hydraulic, separate for each device Pre-heating with autonomous heating function 14TC-10 Teplostar Fuel tank Engine lubrication system On-board gearbox and attachable implement hydraulic system 400 l 32 l 8 l 150 l Hydraulic pump Max pressure Control valve Filtration PSM MPa sectional (Belarus) double filtration: at suction, full-flow at discharge Undercarriage Frame rigid, four-point load-bearing structure made of HSS steel, high welding accuracy Track rollers lifetime lubricated, on sliding bearings (journals) Operating, t 24,2 Specific ground pressure (from mpa the equipment) Number of track rollers Track chain Track shoe width Track shoe grouser Track adjuster 7 bottom rollers on each side / 2 carrier rollers on each side 45 reinforced track shoes on each side 900 mm 65 mm hydraulic, manual 32 33

18 On-board gearboxes Control Brake system Hydrostatic Power Bosch-Rexroth, DANFOSS, Linde Hydraulics hydraulic pump coupled with hydraulic motor with stepless transmission shift. planetary (Germany/Italy) electric and hydraulic servo hydraulic (pilot-operated check valve), normally closed multiple-disc clutches Pipe Layer Equipment The values in brackets are given for 9m boom Load capacity at 2.5 m (1.22 m) boom reach, t nominal is 30 Max calculated is 61 Winch Boom length, m 8,6 Boom weight, t 1,9 2 pcs with hydraulic drive Hook single Operator s Seat. Travel Control Cab hexagonal, improved visibility, twindow insulation, with springs Mass of the counterweight with the frame 9 Rope size, diameter x length hook: 21 mm x 74m / 21 mm x 84 m Boom: 21 mm x 68 m / 21 mm x 78 m Safety Seat emergency hatch, FOPS, outer battery compartment ergonomic, with seat belt Filling Values Attachable Implement Control System Travel and attachable implement control 4-position joysticks Cooling system Fuel tank Engine lubrication system On-board gearbox and attachable implement hydraulic system 60 l 500 l 32 l 8 l 200 l hydraulic, separate for each device Hydraulic pump PSM Max pressure 28 MPa Control valve sectional (Belarus) Filtration double filtration: at suction, full-flow at discharge Operating, t 44 / 52 Specific ground pressure (from the equipment) 0.09 mpa 34 35

19 Pipe Layer Machines TG HST Engine On-board gearboxes Control Hydrostatic Power Bosch-Rexroth, DANFOSS, Linde Hydraulics hydraulic pump coupled with hydraulic motor with stepless transmission shift. planetary (Germany/Italy) electric and hydraulic servo YMZ / Russia Power, kw/hp 242/330 Min rated consumption, 214 (157) g/kw (g/hp) Operating volume l Torque / torque backup / reserve power 1180 Nm at rpm Electric starter St / 8.1 kw Generator 24V/80A Storage battery 2*12V/ 380Ah Pre-heating with 14TC-10 Teplostar autonomous heating function Load capacity of TG HST, tons т ,8 т т Load capacity according to SAE J743 B Load capacity according to ISO т Cab hexagonal, improved visibility, twindow insulation, with springs Operation range according to Industrial Safety Rules Load capacity according to Industrial Safety Rules Boom reach relative to tip over rib, m Brake system Operator s Seat. Travel Control Safety Seat Travel and attachable implement control hydraulic (pilot-operated check valve), normally closed multiple-disc clutches forced ventilation, emergency hatch, FOPS, outer battery compartment ergonomic, with seat belt 4-position joysticks Undercarriage Frame Track rollers Number of track rollers Track chain Track shoe width Track shoe grouser Bearing area Track adjuster rigid load-bearing structure made of HSS steel, high welding accuracy lifetime lubricated, on sliding bearings (journals) 8 bottom rollers on each side / 2 carrier rollers on each side 48 track shoes / 860 mm / 88mm / 6.45 m2 48 track shoes / 960 mm / 88mm / 7.2 m2 48 track shoes / 1010 mm / 88mm / 7.52 m2 hydraulic, manual 36 37

20 Pipe Layer Equipment The values in brackets are given for 9m boom Hook Max boom height Max extended boom Min hoisting/ lowering speed is actuated through a sheave system with a winch hoisting height 7.5 m Hook lowering height: 2.5 m hoisting height 2 m Hook lowering height: 8 m 0.01 m/sec 0.13 m/sec Modern CABLE LAYER MACHINES TM10.00 HST15 KVG-280, TM10.00 HST12 KVG-220 Boom welded box-shaped structure. It is actuated through a sheave system with a winch Boom reach min is 1.22 m, max is 9 m Filling Values Cooling system Fuel tank 80 l 700 l Attachable Implement Control System hydraulic, separate for each device Max pressure 30 MPa With hydrostatic power transmission, track width is 600 mm ( mm as an option) Engine lubrication system 32 l Control valve sectional (Belarus) On-board gearbox and attachable implement hydraulic system 8 l 250 l Filtration double filtration: at suction, fullflow at discharge Description TM10.00B HST9 with KVG-220 TM10.00 HST15 with KVG-280 Cable laying depth, mm Operating Cable diameter, mm Up to 50 (up to 80 as an option) Up to 50 (up to 80 as an option), t 60 Detachable counterweight, t 14 Boom, t 2,5 Provisional weight on the frame, t 6 Vehicle weight without provisional elements (boom, under boom, platform, all the 38 counterweights, blocks with hooks) Specific ground pressure (depending on the track width 860/960/1010 mm) 0.99 / 0.89 / 0.84 mpa Pipe diameter, mm 32, 40, 50, 63 32, 40, 50, 63 Cable laying speed, km/h Number of drums, pcs: - Drum diameter is 2250 mm 2 2(3) - Drum diameter is 2500 mm 2 2 Layer part turn to the left and to the right, mm option 1225 Operating weight without cable, kg

21 Main Advantages Efficient cable and pipe laying in the ground with surface hardness range from 1 to 4 Thanks to 8-roller truck and 600 mm track it made it possible to decrease ground pressure in comparison with the basic tractor; that allows using the cable layer machine on soft ground (waterlogged, boggy, peaty). Transport width clearance is 2500 mm. HST allows implementing traction parameters and ensures perfect maneuverability; and allows performing large scale laying operations. Maximal traction is 31 t is provided at speed up to 1.8 km/h. It is possible to set the layer part of the machine at 1225 mm on both sides in horizontal plane. This provides cable laying in complex environment. KVG-280 knife vibration in vertical direction leads to 30-60% decrease of traction resistance depending on soil harness and travel speed Self-loading and offloading of the cable drum Research development SELF-PROPELLED WELDING MACHINE On the chassis of TM10 HST9 tractor Self-Propelled Welding Machine on the chassis of TM10 HST9 crawler tractor is a special motorized mechanism used in completion with welding equipment. The welding equipment on the tractor is used during construction, overhaul and regular maintenance of gas and oil pipelines and other welding during erection. Crawler Tractor TM10.00B HST9 MTO1 KVG-1(2) On TM10.00B HST12 tractor chassis, track width is 900 mm Description PVG-1 KVG-1 KVG-2 Cable laying depth, mm Cable diameter, mm Up to 80 Up to 80 Up to 80 Pipe diameter, mm 32, 40, 50, 63 32, 40, 50, 63 32, 40, 50, 63 Turn, mm TM10.00B HST9 MTO1 Crawler Tractor is a platform for special equipment. The machine is dedicated for transporting and power driving of snow tamper. In general, the complex is dedicated for constructing winter roads. The complex is a research development; it greatly improves the quality of road surface with 3-time reduction of constructing cost for winter roads. Besides, the crawler tractor TM10.00B HST9 MT01 can be used as a platform for drilling machines (USh2T type), manipulators with welding machines and other special implements; it is dedicated for pipeline construction and transportation of cargo or passenger (berthing) bodies. The peculiarity of TM10.00B HST9 MTO1 Crawler Tractor is big load capacity, but flotation capacity is better than wheeled chassis

22 TM10.00 HST 9 Tractor TM10.00 HST 10 Tractor Diesel motor YMZ-236M / Cummins (180 hp) Diesel motor YMZ-236M2 / Cummins (180 hp) Nominal traction on the track is 14 t Nominal traction on the track is 15 t Max is 20 t Max is 20 t Reserve power (torque backup): 25% Reserve power (torque backup) ~ 25% Basic model with hydrostatic transmission (HST is analogous with Liebherr) Track Configuration 500/700 mm 6 bottom rollers 14.5 t engine preheater, separator-filter, FOPS, ROPS, armored bottom Basic model with Hydrostatic Power Bosch- Rexroth, DANFOSS, Linde Hydraulics Configuration 6 bottom rollers engine preheater, separator-filter, FOPS, ROPS, armored bottom 15.5 t TM10.10 HST 9 Bulldozer TM10.10 HST 10 Bulldozer The bulldozer with straight half-u blade with hydraulic skewness (E-type) Rigid tow hook 16.5 t The bulldozer with straight half-u blade with hydraulic skewness (E-type) Rigid tow hook 17.7 t TM10.11 HST 9 Bulldozer TM10.11 HST 10 Bulldozer The bulldozer with straight half-u blade with hydraulic skewness (E-type) With single shank ripper (H-type) 17.9 t The bulldozer with straight half-u blade with hydraulic skewness and single/triple shank ripper 19 t TM10.10B HST 9 Bulldozer (Swamp Buggy) TM10.10B HST 10 Bulldozer (Swamp Buggy) The bulldozer with a straight blade (B4-type) - Configuration for swamp buggy track is 900 (700) mm wide, 7 bottom rollers 19 t The bulldozer with straight blade (B4-type), configuration for swamp buggy Rigid tow hook, track is 900 (700) mm wide 7 bottom rollers 20 t 42 43

23 TM10.00 HST 12 Tractor TM10.00 HST 15 Tractor Diesel motor YMZ-238 / Cummins (240 hp/180 hp) Diesel motor YMZ-238B / Cummins (300 hp) Nominal traction on the track is 14 t Nominal traction on the track is 20 t Max is 24 t Max is 28 t Basic model with hydrostatic transmission (HST Germany, Italy, is analogous with Liebherr) 7 bottom rollers Reserve power (torque backup): 25% Configuration engine preheater, separator-filter, glass unit, FOPS, ROPS, armored bottom 17.2 t Basic model with hydrostatic transmission (HST is analogous with Liebherr) Track 500 mm (700 mm) 7 bottom rollers Reserve power (torque backup) 40% Configuration engine preheater, separator-filter, glass unit, FOPS, ROPS, armored bottom 20.7 t TM10.10 HST 12 Bulldozer TM10.10 HST 15 Bulldozer The bulldozer with straight half-u blade with hydraulic skewness Rigid tow hook 19.5 t The bulldozer with straight half-u blade (E15-type) with hydraulic skewness and rigid tow hook 23.7 t TM10.11 HST 12 Bulldozer TM10.11 HST 15 Bulldozer Tractor with bulldozer attachment and ripper The bulldozer with straight half-u blade with hydraulic skewness With single shank ripper (H-type) 20.7 t Tractor with bulldozer attachment and ripper The bulldozer with straight half-u blade (E15-type) with hydraulic skewness, and single shank ripper (15H2-type) 26.3 t TM10.10B HST 9 Bulldozer (Swamp Buggy) TM10.10B HST 15 Bulldozer (Swamp Buggy) The bulldozer with straight blade Configuration for swamp buggy (B41-type), rigid tow hook track is 900 (700) mm wide 20.4 t The bulldozer with straight blade (15B41-type) - Configuration for swamp buggy with rigid tow hook Track width 900 (700) mm Tractor with bulldozer 24,3 t Tractor with bulldozer attachment attachment 44 45

24 PIPE LAYER CRANE TO12.24 HST TG30.50 HST Engine YMZ-236M2 (180 hp) Engine YMZ-238B (300 hp) Winch hydraulic drive - Nominal load capacity 12 t (at 2.5 m) Length of the boom 7 m / 9 m Winch planetary gearbox (Italy) Hydrostatic Power Load capacity 12 t Pipe Layer Crane Planetary winch hydraulic drive Nominal load capacity Length of the boom Load capacity - 30 t (at 2.5 m) 7 m / 9 m hydrostatic power 30 t Pipe Layer Crane TG20.32 HST TG HST Engine YMZ-238M2 (240 hp) Engine YMZ (400 hp) Winch hydraulic drive - Track 900 mm (700 mm) Nominal load capacity 20 t (at 2.5 m) Length of the boom 7 m / 9 m Winch planetary gearbox (Italy) hydrostatic power Load capacity 20 t Planetary winch hydraulic drive Nominal load capacity Length of the boom Load capacity - 50 t (at 2.5 m) 8.6 m hydrostatic power 50 t Pipe Layer Crane Pipe Layer Crane 46 47

25 TM10.00 PG Track Loader TM10.00B HST 12 KVG-2(1) Description PG-35 PG-50 PG-70 Track 900 mm Tractor chassis TM10.00 HST9 TM10.00 HST12 TM10.00 HST15 Dedicated for cable and pipe laying up to 63 mm diameter The loader on HST9/ HST12/ HST15 chassis Engine, kw/ hp Maximal traction on the track, t Bucket capacity, m3 Nominal load capacity, t YMZ-236M 132/180 YMZ-238M2 176/240 YMZ-238B 220/ Cable layer machine KVG2 (KVG1) on TM10.00B HST12 chassis Cable laying depth Speed of cable laying Layer part turn to the left and to the right of the machine (without tractor) For accelerated cable laying 1.2/ 1.5 m ~4-6 km/shift 1140 mm (no) 5000 kg a pre-ripper is used on a separate bulldozer TM10.00 HST 12 KVG 220 MT-10 Universal Transporter Cable layer machine KVG 220 on the chassis of TM10.00 HST 9 Cable laying depth 1500 mm Cable diameter up to 50 mm (up to 80 mm as an option) Layer part turn to the 1140 mm left and to the right TM10.00 HST 15 KVG 280 Description MT10-10 MT10-15 МТ10-20 Engine, kw/ hp YMZ- 236M 132/180 YMZ- 238M2 176/240 YMZ- 238B 220/300 Track basic width, mm 500 (900) 700(900) 900 (1100) Operating weight, t Max load capacity*, t Speed of cable laying ~11 km/shift MT10-20 Chelyabinets-32 and KS-55733B Universal all-terrain Gross weight, t Cable laying depth 1500 mm transport platform, 32 t load Cable diameter up to 50 mm (up to 80 mm as an capacity Cable layer machine KVG option) 280 on the chassis of TM10.00 HST 15 Rollers 7 pcs * the machine completeness can be different from the one shown in the pictures/descriptions Layer part turn to the 1140 mm left and to the right 48 49

26 TM10.00 HST9 Hydraulic Mulcher TM10.00B HST9, USh-2T4V Drilling Machine Grasp 2000 mm For drilling seismic exploration, exploration, geotechnical, technical and other wells Rotor diameter: 500 mm PTO shaft- Provides rotary auger drilling of The mulcher with hydraulic drive on TM10.00 HST9 chassis Operating speed Tree diameter Possibility to attach implements TM10.00B HST9, MBSh10 Drilling Machine up to 5 km/h mm any capacity and grasp Multi-purpose drilling machine on TM10.00B HST9 chassis driven Conditional depth of drilling Drilling tool mm diameter wells; dry rotary core drilling and core drilling with compressed air of up to 190 mm wells; percussive rotary core drilling and non-core drilling using downhole hammers with an auger 60 m With compressed air 100 m Pneumatic hammer 50 m not included in the price Bulldozer blade possible to install Tool feed hydraulic drive auger drilling tool Maximal drilling depth m Drilling diameter mm TM10.00B HST9, MBSh10 Drilling Machine Output Производительность up to 120 m/h до 120 м / ч TM10.00 HST9, BTC-150BM (BTC- 150G) Drilling Machine TM10.00 HST9, ATM01 Trencher Roller-bit (auger) Drive drilling in soft, frozen rocks, at blasting, when mining from PTO shaft, hydraulic (BTC- 150G) Trencher. TM10.00 HST9 chassis Width 280 mm Depth 2 m Options width 140/400 mm depth 2.7 m Tilt hydraulic pusher - Tractor Drilling Machine on TM10.00 HST9 chassis Toll feed hydraulic drive up to 30 degrees In rocks drilling depth is up to 32 m, 160 mm wells Output m/h 50 51

27 TM10.00B HST9 PT-25G Trailer crane on TM10.00B HST9 chassis Track Dedicated for loading Winch drive Max load capacity Max hoisting height 900 mm off-loading and installation during maintenance of drilling and oilfield equipment. Suspended cargo can be moved. hydraulic 25 t (at 2.5 m boom reach) 8.5 m TTM10.00 HST9 PM-6.3 Winch drive Max load capacity Max hoisting height from the tractor motor through PTO shaft 6.3 t (at 2.3 m boom reach) 6 m Installation Elevator +7 (800) Free throughout Russia 28P, Geroev Tankograda str., Chelyabinsk, (351) tm10.ru info@tm10.ru «DST Ural» 52 53