Section 00 Chapter 3 GENERAL SPECIFICATIONS AND SPECIAL TORQUES NH

Transcription

1 Section 00 Chapter 3 GENERAL SPECIFICATIONS AND SPECIAL TORQUES NH

2 TABLE OF CONTENTS GENERAL SPECIFICATIONS Fluid Capacities and Types Hydraulic Specifications Electrical Specifications Cab Fuse Identification and Amperage Cab Relay Identification (Facing Rear Window) Engine Compartment Fuse/Relay Identification (Power Distribution Box) Lamps and Bulbs Accessory Connectors Air Conditioner System Specifications Engine Specifications Transmission Specifications Hitch Specifications SPECIAL TORQUES

3 Fluid Capacities and Types GENERAL SPECIFICATIONS All fluid capacities listed are a guide to the quantities required. Always use dipsticks, sight glasses or level plugs to ensure that the units are filled to the correct level. Coolant Capacity TG 210 and liters 6 U.S. gal TG 255 and liters 6.5 U.S. gal Fluid Type Percent Ethylene Glycol and Water Engine Oil Capacity With Filter Change liters 5.5 U.S. Gal Without Filter Change liters 5 U.S. Gal Oil Type...NH No. 1 Engine Oil Transmission/Hydraulic System Capacity MFD liters 45.5 U.S. gal Oil Type... New Holland Ambria 134D MFD Axle Differential 10 Bolt liters 13 quarts 12 Bolts liters 12.3 quarts Supersteer (all) liters 11.1 quarts Oil Type...API GL5 SAE 85W-140 Planetary (Each) 10 Bolts liters 2.8 U.S. pints 12 Bolts liters 6.8 U.S. pints Oil Type... SAE 85W-140 Gear Lubricant Fuel Tank Standard - TG 210 and liters 130 U.S. gal Standard - TG 255 and 285 (Optional - TG 210 and 230) liters 160 U.S. gal Fuel Type... No. 2 Diesel Hydraulic Specifications Pump Type... Axial Piston, Closed Center Load Sensing Maximum Pressure at Rated Engine RPM at Pump bar 3250 psi Maximum Flow at Remote Couplers at 2000 Engine RPM Standard l/min 36 gpm Optional Mega Flow l/min 64 gpm Electrical Specifications Type of System...12 Volt Negative Ground Batteries...Two 1000 CCA Low Maintenance, Group Size 31 Alternator...Bosch 135 Amp Output Cranking Motor...Nipendenzo, 12 Volt, 4 kw 00-3

4 Cab Fuse Identification and Amperage A 52 15A ITALIAN BRAKES 5A 43 15A 44 15A A 47 30A 48 20A 49 30A ICU/PMU ECU 36 15A 37 5A 38 10A 39 10A 40 10A 41 5A 42 10A SW B+ CONTROLLER AFS TRANS CONT A A 32 5A 33 10A 34 SW B+ UNSW. B+ STOP 22 10A 23 15A 24 10A SUSP. AXLE 25 20A 26 10A 27 LIGHTS SW. B+ 5A C /F TEMP. DISPLAY 5A 15 30A 16 ICU/PMU 5A 17 5A 18 10A 19 10A 20 20A 21 10A UNSW B+ 8 20A 9 15A 10 15A 11 20A 12 30A 13 30A A1 1 5A A 4 10A 5 20A 6 10A 7 10A RI02G018 Fuse No. Circuit 1 Electronic Governor (TG 255 & TG 285) 5 2 Cruise Control 5 3 Rear Fender Worklights 20 4 Beltline Worklights 10 5 Roof Worklights 20 6 Worklight/Headlight Interlock 10 7 Battery Power to Key Switch 5 8 Headliner Shelf Auxiliary Power/3-Pin/ Cigar Outlets (Unswitched) 9 Seat Power Cab Pressurizer Blower (Continuous) 15 Fuse Amp 11 Cigar Lighter/RH Fender Console (Unswitched) Exterior 7-Pin Connector (Switched) RH Front Post/RH Fender 3-Pin Auxiliary Connectors (Unswitched) Governor (MX255 & MX285) Tractor Instrumentation (Unswitched) 5 18 High Beam Relay Dome Light/Map Light/Radio (Unswitched) Amber Flashers Tail Lights Stop Lights Strobe Light/Beacon Fuse No. 24 Mirror/Radio Ether/Horn Circuit Auto Climate Display (With Fuse = C, Without Fuse = F) 29 Seat Heater AFS (Switched) AFS (Unswitched) RH ArmRest Controller (Switched) True Ground Radar 5 35 Transmission Controller Remote Hydraulic Controller Tractor Instrumentation (Switched) 5 38 PTO/Differential Lock/MFD Controller Hitch Controller Case Data Bus, Tractor 5 42 Case Data Bus Diagnostic Connector RH Front Post/RH Fender 3-Pin Connectors (Switched) HVAC Controller Headliner Shelf 3-Pin Connectors (Switched) HVAC Blower 30 51* Front Wiper/Washer Rear Wiper/Washer Italian Brakes 5 Fuse Amp 5 (Unswitched) - Unswitched power (Continuous). (Switched) - Power available when keyswitch is in ON position. * = Circuit breaker. 00-4

5 Cab Relay Identification (Facing Rear Window) RH02G BRAKE LAMPS 6. NEUTRAL RELAY 11. GOVERNOR (KEY SWITCH) 2. OPEN 7. OPEN 12. FENDER WORK LAMPS 3. REAR ROOF WORK LAMPS 8. BELTLINE WORK LAMPS 19. CONTROLLER POWER 4. WORK LAMP INTERLOCK 9. FRONT ROOF WORK LAMPS 5. PARK LATCH 10. CAB PRESSURIZER BLOWER Engine Compartment Fuse/Relay Identification (Power Distribution Box) STARTER FUEL SHUT OFF F6 30 F7 25A 30A (D1) (D2) (3) (4) 12 30A 15A CENTER & SIDE 25A 30A F1 30 F2 1 2 HIGH BEAM LOW BEAM F8 15 F9 15A 15A 5 15 F5 15A (D1) (D2) 15 HIGH BYPASS RH02G CENTER SIDE & HID 6. FUEL SHUT OFF RELAY 11. FUEL SHUT OFF RELAY 16. DIODE 1 WORKLAMP RELAY FUSE FUSE 2. HIGH/LOW BEAM & 7. STARTER RELAY FUSE 12. CENTER AND SIDE 17. NOT USED - DIODE 2 BYPASS RELAYS FUSE WORKLAMP RELAY 3. STARTER RELAY FUSE 8. RH LO BEAM RELAY FUSE 13. HIGH BEAM RELAY 4. RH HI BEAM FUSE 9. LH LO BEAM RELAY FUSE 14. LOW BEAM RELAY 5. LH HI BEAM RELAY FUSE 10. STARTER RELAY 15. HIGH BYPASS RELAY 00-5

6 Lamps and Bulbs Application G.E. Bulb No. (Watts) Dome Lamp Bulb... Case Part No R1, (10W) Console Lamp Bulb... No. 168 Flasher Lamp Bulb... No Head Lamps... No. H4, (55W/60W Halogen) Brake Lamps (37W) Side Work Lamps...No. 885, (50W) Front and Rear Flood Lamps, Optional Fender/Rear Roof/Beltline Flood Lamps... No. H3, (55W) Tail Lamp Bulbs... No. 3157, (37W) Fender Standard Work Lamp...No. 894, (37W) Front Roof Work Lamp...No. 894, (37W) Center Grille Work Lamp...No. 885, (50W) HID Center Roof Work Lamp...New Holland Part No , (35W) Strobe Light...No. 400, (80W) Number Plate Lamp... Case Part No. P40556 Accessory Connectors 7 Terminal Electrical Outlet... Equipped for Directional Lamps, Tail lamps and 12 Volt Power for Implements with Fuse Protection 3 Pin Cab Connector (2 Standard) (2 Optional)...12 volt Power with/or with/out Key Switch and Direct Ground for Implement Controllers and Monitors! WARNING: Do not look directly into the High Intensity Discharge Lamp. Eye damage can occur. M638! WARNING: Do not tamper with the ballast on the High Intensity Discharge Lamp as it contains high voltage. Personal injury or death can occur. M

7 Air Conditioner System Specifications Refrigerant Type...HFC-134A Per ARI Standard 700 System Capacity grams 4.63 lb Compressor Manufacture...SANDEN Model...SD 7H15MD4609 Clutch Current Draw at 12 Volts...2 Amps Clearance Between Front Plate and Pulley to 0.8 mm to 0.32 inch Engine Specifications Make... CDC Model... 6TAA - Magna Force Firing Order Bore and Stroke mm x 135 mm Displacement liters Engine Speeds High Idle TG to 2505 RPM TG to 2485 RPM TG 255 and TG to 2410 RPM Rated Engine Speed All Engines RPM Low Idle All Engines to 950 RPM Valve Clearance-Engine Cold Intake Valves mm Exhaust Valves mm inch inch Transmission Specifications Number of Forward Speeds Full Power shift Reverse Speeds...4 Creeper Speeds (If Equipped)...6 Forward and 2 Reverse Hitch Specifications Type Hitch... Three Point, Category III (Convertible to II or IIIN) Lift Capacity at 24 Inch (610 mm) Behind Lift Point Standard Hitch TG 210 and Kg ( lb) TG Kg ( lb) TG Kg ( lb) Optional Hitch TG 210 and Kg ( lb) TG 255 and Kg ( lb) European Hitch TG Kg ( lb) TG 230 and Kg ( lb) TG Kg ( lb) Type Draft Arms TG 210 and Telescoping TG 255 and Rigid With Integral Quick Coupler Position Control and Draft Control... Electronic 00-7

8 SPECIAL TORQUES Alternator Mounting Bolts Nm Pulley Retaining Nuts to 70 Nm MFD Steering Cylinder and Axles King Pin Retaining Bolts to 170 Nm Socket Clamp to Steering Cylinder to 108 Nm Steering Cylinder Tapered Stud...10 Bolt / 12 Bolt Nm Tie Rod Tapered Stud Nm Differential Housing to Axle Bolts to 135 Nm Ring Gear Bolts to 190 Nm Wheel Carrier to Knuckle Bolts to 125 Nm Planetary Carrier to Wheel Hub Screws to 16 Nm Wheel Hub Drain / Filler Plug Nm Front Wheel Disc to Rim Nuts - MFD to 366 Nm Disc to Front Axle Hub Nut - MFD to 425 Nm MFD Drive Shaft Retaining Bolts to 73Nm MFD Output Shaft Bearing Cage M20 X to 485 Nm M20 X to 485 Nm Transmission Speed to Range Transmission Retaining Bolts M16 X to 260 Nm M16 X to 250 Nm M20 X to 486 Nm Range Transmission to Rear Frame M16 X to 262 Nm M16 X to 250 Nm M16 X to 250 Nm Wheel to Hub Bolts to 569 Nm Wheel Bushing Bolts to 350 Nm Axle Carrier to Rear Frame - All to 265 Nm (Thru Axle Carrier Flange Into Rear Frame) Differential and Differential Lock Ring Gear Retaining Bolts to 328 Nm Differential Lock Clutch Cage Retaining Bolts to 328 Nm Hydraulic PTO PTO Housing Retaining Bolts Nm PTO Speed Sensor to 22 Nm 74 lb ft 44 to 52 lb ft 115 to 125 lb ft 70 to 80 lb ft 10 Bolt 140 / 12 Bolt 200 lb ft 200 lb ft 90 to 100 lb ft 120 to 140 lb ft 89 to 90 lb ft 7 to 12 lb ft 30 lb ft 220 to 270 lb ft 285 to 315 lb ft 49 to 54 lb ft 277 to 358 lb ft 277 to 358 lb ft 173 to 192 lb ft 162 to 185 lb ft 317 to 358 lb ft 171 to 193 lb ft 162 to 184 lb ft 162 to 184 lb ft 390 to 420 lb ft 220 to 260 lb ft 169 to 195 lb ft 219 to 242 lb ft 219 to 242 lb ft 40 lb ft 12 to 16 lb ft 00-8

9 Hydraulics Hydraulic Pump Mounting Bolts to 151 Nm Charge / Lubrication Pump Mounting Bolts to 151 Nm Solenoid Valve Installation Torque to 25 Nm Solenoid Valve Coil Retaining Nut... 5 to 8 Nm Remote Valve Retaining Nuts to 69 Nm Load Check Valve Body to 41 Nm Load Check Poppet Spring Retainer... 4 to 5 Nm Check Valve Body to 19 Nm Check Valve Plug... 4 to 4.5 Nm PTO Spool End Plug to 25 Nm Inching Spool End Plug to 25Nm Pressure Transducer to 25 Nm Rear Hitch Top Link Mounting Bracket (M20) to 550 Nm RH and LH C Bracket Casting Bolts (M24) to 950 Nm Rocker Tie Bolt (M24) to 550 Nm Quick Coupler Latch Bolt (M16) to 125 Nm Air Conditioning Compressor Clutch Retaining Nut to 20 Nm Compressor Oil Fill Plug to 24 Nm Dust Cover Screws... 7 to 11 Nm Low / High Pressure Switch to 20 Nm 99 to 112 lb ft 99 to 112 lb ft 14 to 18.5 lb ft 4 to 6 lb ft 45 to 51 lb ft 25 to 30 lb ft 3 to 4 lb ft 12 to 14 lb ft 3 to 3.5 lb ft 14 to 18.5 lb ft 14 to 18.5 lb ft 14 to 18.5 lb ft 360 to 405 lb ft 625 to 700 lb ft 360 to 405 lb ft 70 to 90 lb ft 11 to 15 lb ft 11 to 18 lb ft 5 to 8 lb ft 10 to 15 lb ft 00-9

10 00-10