VERSION 2. PVC FITTINGS & VALVES Technical Catalogue
|
|
- Patricia Gladys Burke
- 5 years ago
- Views:
Transcription
1 VERSION 2 PVC FITTINGS & VALVES Technical Catalogue
2 INTRODUCTION Plasson s innovative products revolutionized the way of connecting polyethylene pipes in the 1960 s. We started with fittings for agricultural irrigation and later developed products for urban water distribution. igh pressure PVC Fittings and Valves are part of Plasson s wide range of products. Plasson has achieved superior designs and products and a genuine commitment to quality, delivery and service. Plasson continues to strive for the future environment. By buying Plasson products you help us invest in our vision of a world where clean, pure water will be everyone s birthright. INTRODUCTION CEMENTED FITTINGS 8-17 ADAPTOR FITTINGS TREADED FITTINGS FITTINGS ACCESSORIES VALVES NORMAL SUPPORT VALVES TREADED SUPPORT CECK VALVES FOOT VALVES 46 AIR RELEASE VALVES 47 VALVES ACCESSORIES TECNICAL SPECIFICATIONS - FITTINGS TECNICAL SPECIFICATIONS - VALVES ASSEMBLY INSTRUCTIONS
3 PRODUCT LIST Socket - Cemented page Elbow - Cemented page Reducing Socket Male - Female - Cemented page Flange Adaptor with O-Ring Cemented page Tee - Cemented page Stub Flat Face to fit Cemented page Elbow - Cemented page Stub Serrated Cemented page End Cap - Cemented page Loose Flange page Union - Cemented page Blind Flange page Short Reducing Bushing - Cemented page Fixed Flange page Reducing Tee Cemented page Socket Adaptor Cemented page ose Adaptor Cemented page Reducer Adaptor M - F - Cemented page 18 3
4 PRODUCT LIST Adaptor Socket M - F - Cemented - page Tee Cemented page Reducing Tee Cemented - page Socket Adaptor Cemented with Reinforcing Ring page Elbow Cemented page Adaptor M - F - Cemented - M - page Reducer Adaptor with Reinforcing Ring Male Cemented - Female - page Tee with Reinforcing Ring Cemented page Union Adaptor F - Cemented - page Adaptor M - F - Cemented - M - page Elbow with Reinforcing Ring Cemented page Adaptor Socket Reinforcing Ring M - F page Bushing Adaptor M - F - Cemented - M - page Metal Pipe & Tap Connectors page ose Adaptor With Nut page Metal Pipe & Tap Connectors page Elbow Cemented - page Socket - page 26
5 PRODUCT LIST Reducing Socket Female - Female - page Reducer Male - Female - page Reducing Nipple page Plug page Tee page ose Adaptor page Elbow page Nipple Socket Male - Female - page Nipple page Cap page Elbow page Fixed Flange page Union Female page Nut for Unions: , , , , page Union Male - Female Cemented page Bushing for Union: page Union Male - Female - page Bushing for Unions: , page 33 5
6 PRODUCT LIST Male Union bush for items , page End for Unions: , , page One Nut Valve page One Nut Valve Male - Female - page End for Unions: , page Two Nut Valve Cemented page O-Ring for Item page Two Nut Valve page Seal for: , page O-Ring for Unions , , , page * Bistop Valve Cemented page * Bistop Valve page Two Nut Valve Cemented page One Nut Valve Cemented page Two Nut Valve page One Nut Valve page One Nut Valve Cemented page One Nut Valve Male - Female - page 42 6
7 PRODUCT LIST One Nut Valve Female - - Compression page Two Nut Valve PE End Connector page Air Release Valve page Valve End Cemented page One Nut Valve Compression PE End Connector page Check Valve Cemented page Check Valve page Knocker Tee Cemented page Valve End page Blue andle page Red andle page Valve Nut page Foot Valve Cemented page PE End Connector page Foot Valve page Air Release Valve Cemented page 47 7
8 PVC CEMENTED FITTINGS Socket - Cemented d E Z I Quality Cod d E l Z Weight PN Pack U C K U C K U C K U C K U C K U C K U C K U C K U C K U C U U U U * * * Quality certifications : U= UNI-IIP, C= NF-CSTB, K = Kiwa * DELIVERY PROGRAM 8
9 PVC CEMENTED FITTINGS Reducing Socket Male - Female - Cemented D d I L I1 d1 E Cod Dxdxd1 L l l1 E Weight PN Pack x 16 x x 20 x x 20 x x 25 x x 25 x x 25 x x 32 x x 32 x x 32 x x 32 x x 40 x x 40 x x 40 x x 40 x x 50 x x 50 x x 50 x x 50 x x 63 x x 63 x x 63 x x 63 x x 75 x x 75 x x 75 x x 75 x x 90 x x 90 x x 90 x x 90 x x 110 x x 110 x x 110 x x 110 x x 125 x x 140 x x 140 x x 200 x
10 Tee - Cemented Z I PVC CEMENTED FITTINGS E d Quality Cod d E l Z Weight PN Pack U C K U C K U C K U C K U C K U C K U C K U C K U C K U C U U U * * * * * Quality certifications : U= UNI-IIP, C= NF-CSTB, K = Kiwa * DELIVERY PROGRAM Elbow - Cemented Z I d E Quality Cod d E l Z Weight PN Pack U C K U C K U C K U C K U C K U C K U C K U C K U C K U C U U U * * * * * Quality certifications : U= UNI-IIP, C= NF-CSTB, K = Kiwa 10 * DELIVERY PROGRAM
11 PVC CEMENTED FITTINGS End Cap - Cemented d E I Quality Cod d E l Weight PN Pack U C K U C K U C K U C K U C K U C K U C K U C K U C K U C U U U Quality certifications : U= UNI-IIP, C= NF-CSTB, K = Kiwa Union - Cemented E d d I Z I1 Cod d E l L1 Z Weight PN Pack
12 PVC CEMENTED FITTINGS Short Reducing Bushing - Cemented D d I L Z Quality Cod Dxd L l z Weight PN Pack U C x U x U C x U x U x U C x U x U x U C x U x U x U C x U x U x U C x U x U x U C x U x U x U C x U x U x U C x U x U x U x x x x x x x x x x * x * x * x * x * x * x * x * x * x Quality certifications : U = UNI-IIP, C = NF-CSTB * DELIVERY PROGRAM 12
13 PVC CEMENTED FITTINGS Reducing Tee Cemented E 1 Z1 I1 E1 d1 d Z I Cod dxd1xd E E1 l l1 Z Z1 1 Weight PN Pack x 20 x x 20 x x 25 x x 20 x x 25 x x 32 x x 25 x x 32 x x 40 x x 32 x x 40 x x 50 x ose Adaptor Cemented D L E Cod d E L Weight PN Pack
14 PVC CEMENTED FITTINGS Elbow - Cemented E d Z I Quality Cod d E Z l Weight PN Pack U C K U C K U C K U C K U C K U C K U C K U C K U C K U C U U U * * * * * Quality certifications : U= UNI-IIP, C= NF-CSTB, K = Kiwa * DELIVERY PROGRAM Flange Adaptor with O-Ring Cemented Quality Cod d E E1 l Z B Weight PN Pack U U U U U U U U U U U U Quality certifications : U = UNI-IIP
15 PVC CEMENTED FITTINGS Stub Flat Face to fit Cemented Quality Cod d E E1 l Z B Weight PN Pack U U U U U U U U U U U U Quality certifications : U = UNI-IIP Stub Serrated Cemented E d B E1 I Z Quality Cod d E E1 l Z B Weight PN Pack U U U U U U U U U U U U * * * Quality certifications : U = UNI-IIP * DELIVERY PROGRAM 15
16 PVC CEMENTED FITTINGS Loose Flange S Dp E E1 Quality Cod d E E1 Dp S N Weight PN Pack U U U U U U U U U U * * * Quality certifications : U = UNI-IIP * DELIVERY PROGRAM Blind Flange Dp E S Cod d E Dp S N Weight PN Pack
17 PVC CEMENTED FITTINGS Fixed Flange Dp d I Z E S Quality Cod d I E Dp S N Z Weight PN Pack U U U U U U U Quality certifications : U = UNI-IIP 17
18 G C PVC ADAPTOR FITTINGS Socket Adaptor Cemented d B I Z Lt Cod dxg C B l Lt Z Weight PN Pack x 3/ x 1/ x 3/ x x 1.1/ x 1.1/ x x 2.1/ x x Reducer Adaptor Male - Female Cemented Cod DxdxG C B L Lt Weight PN Pack x 20 x 1/ x 25 x 3/ x 32 x x 40 x 1.1/ x 50 x 1.1/ x 50 x 1.1/ x 63 x x 75 x 2.1/ x 90 x Adaptor Socket Male - Female Cemented d B G C L Lt Cod dxg C B L Lt Weight PN Pack x 1/ x 3/ x x 1.1/ x 1.1/ x x 2.1/ x x
19 PVC ADAPTOR FITTINGS Tee Cemented E G Lt I d E Z I Cod dxgxd E l Lt Z Weight PN Pack x 3/ x 1/ x 3/ x x 1.1/ x 1.1/ x x 2.1/ x x Elbow Cemented Z Lt G E d E Cod dxg E l Lt Z Weight PN Pack x 3/ x 1/ x 3/ x x 1.1/ x 1.1/ x x 2.1/ x x Adaptor Male - Female Cemented - Male D d I L B Lt R C Cod DxdxR C B l L Lt Weight PN Pack x 12 x 3/ x 16 x 1/ x 20 x 3/ x 25 x x 32 x 1.1/ x 40 x 1.1/ x 50 x x 63 x 2.1/ x 75 x x 90 x
20 PVC ADAPTOR FITTINGS Union Adaptor Female - Cemented E d Lt Z Lt G Cod dxg E l Lt Z Weight PN Pack x 3/ x 1/ x 3/ x x 1.1/ x 1.1/ x x 2.1/ x x Adaptor Male - Female - Cemented Male - D d I L B Lt R C Cod DxdxR C B l L Lt Weight PN Pack x 16 x 3/ x 20 x 1/ x 25 x 3/ x 32 x 1 46, x 40 x 1.1/ x 50 x 1.1/ x 63 x x 75 x 2.1/ x 90 x x 110 x Bushing Adaptor Male - Female - Cemented Male - D d I L B Lt R C Cod DxdxR C B l L L1 Weight PN Pack x 20 x 3/ x 25 x 1/ x 32 x 3/ x 40 x x 50 x 1.1/ x 63 x 1.1/ x 75 x x 90 x 2.1/ x 110 x
21 PVC ADAPTOR FITTINGS ose Adaptor With Nut G E Cod GxE E Weight PN Pack /4 x x /4 x /2 x x /4 x /4 x Elbow Cemented - E G Z I d Cod dxg E Z l Weight PN Pack x 3/ x 1/ x 3/ x x 1.1/ x 1.1/ x Reducing Tee Cemented - Cod dxgxd E E1 l l1 Z Z1 1 Weight PN Pack x 1/2 x x 1/2 x x 3/4 x x 1/2 x x 3/4 x x 1 x x 3/4 x x 1 x x 1.1/4 x x 1 x x 1.1/4 x x 1.1/2 x
22 PVC ADAPTOR FITTINGS Socket Adaptor with Reinforcing Ring Cemented - Cod dxg C B l Lt Z Weight PN Pack x 3/ x 1/ x 3/ x x 1.1/ x 1.1/ x Reducer Adaptor with Reinforcing Ring Male - Cemented Female - Cod DxdxG C B L Lt Weight PN Pack x 20 x 1/ x 25 x 3/ x 32 x x 40 x 1.1/ x 50 x 1.1/ x 50 x 1.1/
23 PVC ADAPTOR FITTINGS Tee with Reinforcing Ring Cemented - Cod dxgxd E l Lt Z Weight PN Pack x 3/ x 1/ x 3/ x x 1.1/ x 1.1/ x Elbow with Reinforcing Ring Cemented - Cod dxg E l Lt Z Weight PN Pack x 3/ x 1/ x 3/ x x 1.1/ x 1.1/ x
24 PVC ADAPTOR FITTINGS Adaptor Socket Reinforcing Ring Male - Female Cod dxg C B L Lt PFA (PN( W x 1/ x 3/ x x 1¼ x 1½ x
25 PVC ADAPTOR FITTINGS Metal Pipe & Tap Connectors, with EPDM gaskets and PVC Spigot x brass nuts Female K G h L B Z E e di D C Di Cod D di G E e Z B L Di K C 5629 h Weight PN Pack , , x 21 x 2 9, ¼ , x 27 x 2 10, ½ 27 22,5 28, x 32 x x 46 x Metal Pipe & Tap Connectors, with EPDM gaskets and PVC Spigot x brass nuts Female K G h c L B Z E e Di di D Cod D di G E e Z B L Di K C 5629 h Weight PN Pack ¾ , x 21 x 2 9, , , x 27 x 2 10, ¼ x 32 x
26 PVC TREADED FITTINGS Socket - B G C Lt Z Cod G C B Lt Z Weight PN Pack / / / / / / Reducing Socket Female - Female - Cod GxG1 C B l Lt Z Weight PN Pack /2 x 3/ , x 3/ ,
27 PVC TREADED FITTINGS Reducer Male - Female - C R Lt B Lt1 G Cod RXG C B Lt Lt1 Weight PN Pack /2 x 3/ /4 x 3/ /4 x 1/ x 3/ x 1/ x 3/ /4 x 1/ /4 x 3/ /4 x /2 x 1/ /2 x 3/ /2 x /2 x 1.1/ x 3/ x x 1.1/ x 1.1/ /2 x 1.1/ /2 x x x 2.1/ x 2.1/ x Tee - Lt E G Cod G E Lt Weight PN Pack / / / / / /
28 PVC TREADED FITTINGS Elbow - Lt G E Cod G E Lt Weight PN Pack / / / / / / Nipple - B Lt R C Cod R C B Lt Weight PN Pack / / / / / / Cap - B G C Lt Cod G C B Lt Weight PN Pack / / / / / /
29 PVC TREADED FITTINGS Union Female E G G Lt Z Lt Cod G E Lt Z Weight PN Pack / / / / / / Union Male - Female Cemented - E d Lt1 B Lt R C Cod dxr Lt Lt1 E C B Weight PN Pack x 3/ , x , x 1.1/ x 1.1/ x Union Male - Female E G Lt1 B Lt R C Cod GxR Lt Lt1 E C B Weight PN Pack /4 x 3/ , x , /4 x 1.1/ /2 x 1.1/ x
30 PVC TREADED FITTINGS Reducing Nipple R1 Lt Lt1 R C B Cod RxR1 C B Lt Lt1 Weight PN Pack /2 x 3/ /4 x 3/ /4 x 1/ x 1/ x 3/ /4 x 3/ /4 x /2 x /2 x 1.1/ x 1.1/ x 1.1/ /2 x 1.1/ /2 x x x 2.1/ x 2.1/ x
31 PVC TREADED FITTINGS Plug - B Lt R C Cod R C B Lt Weight PN Pack / / / / / / ose Adaptor C R Lt B E Cod RxE C B Lt Weight PN Pack / 4 x / 8 x / 2 x / 4 x x / 4 x / 2 x x / 2 x Nipple Socket Male - Female - C R G Lt B Lt1 Cod RxG C B Lt Lt1 Weight PN Pack /8 x 1/ /2 x 3/ /4 x x 1.1/ /4 x 1.1/ /2 x /2 x 2.1/ x 2.1/ x /2 x /2 x x
32 PVC TREADED FITTINGS Elbow E G Lt Z Cod G E Z Lt Weight PN Pack / / / / Fixed Flange Dp G Lt Z E S Cod G Lt E Dp S N Z Weight PN Pack / / /
33 PVC FITTINGS ACCESSORIES Nut for Unions: , , , , , E G E1 Cod d G E E1 Weight PN / / / / / / Bushing for Union: R d Z I Cod d R l Z Weight PN / / / / / / Bushing for Unions: , R G Z Lt Cod G R Lt Z Weight PN /8 3/ / /4 1.1/ / / /2 2.1/ / /2 3.1/
34 PVC FITTINGS ACCESSORIES Male Union bush for items , B Lt R1 R C Cod R R1 Lt C B Weight PN /4 1.1/ / / /2 2.1/ / End for Unions: , , d E I Z Cod d l Z E Weight PN End for Unions: , Cod G Lt Z E Weight PN / / / / / /
35 PVC FITTINGS ACCESSORIES O-Ring for Item s d Cod ø d s ,17 3, ,1 3, ,65 5, ,16 5, ,04 5, ,92 5, ,97 5, ,84 6, ,9 6, ,77 6, ,17 6, ,27 6, ,67 6, Seal for: , e D d Cod ø d D e
36 PVC FITTINGS ACCESSORIES O-Ring for Unions , , , , s d Cod ø d s / / / / / * / * O-Ring for Unions: 5083,
37 Two Nut Valve Cemented VALVES Normal Support Cod d l Z F J K DN Weight PN Pack Two Nut Valve Cod G Lt Z F J K DN Weight PN Pack / / / / /
38 One Nut Valve Cemented VALVES Normal Support Cod d DN l Z J F K Weight PN Pack One Nut Valve Cod G DN l Z J F K Weight PN Pack / / / / / One Nut Valve Male-Female- Cod RxG Lt Z F J K DN Weight PN Pack / / / / /
39 Two Nut Valve Cemented VALVES Support Cod d l Z F J K DN Weight PN Pack Two Nut Valve Cod G Lt Z F J K DN Weight PN Pack / / / / / /
40 * Bistop Valve - Cemented VALVES Support X00 Cod G DN l Z F J K Weight PN Pack 112X X X X X X X X X X * with FPM O-Ring INDIVIDUALLY TESTED * Bistop Valve X10 Cod G DN l Z F J K Weight PN Pack 112X1003 3/ X1005 1/ X1007 3/ X X / X / X X / X X * with FPM O-Ring INDIVIDUALLY TESTED 40
41 One Nut Valve Cemented VALVES Support Cod d DN l Z J F K Weight PN Pack One Nut Valve Cod G DN l Z J F K Weight PN Pack / / / / / /
42 One Nut Valve Male-Female- VALVES Support Cod RxG Lt Z F J K DN Weight PN Pack / / / / / One Nut Valve Female--Compression F J d G K Lp Z Lt Cod dxg Lt Z Lp F J K DN Weight PN Pack /2 x /4 x x /4 x /2 x x
43 F l Two Nut Valve PE End Connector VALVES Support Cod d DN l Z J F K Weight PN Pack * * * * DELIVERY PROGRAM One Nut Valve Compression PE End Connector d J K Lp Z Cod d DN l Z Lp F J K Weight PN Pack , , , ,
44 CECK VALVES Check Valve Cemented X00 Cod d l Z F K Weight PN Pack 110X X X X X X X X X X with FPM O-ring with EPDM O-ring with PTFE coated spring + EPDM O-rings with PTFE coated spring + FPM O-rings Check Valve X10 Cod G l Z F K DN Weight PN Pack 110X1003 3/ X1005 1/ X1007 3/ X X / X / X X / X X with FPM O-ring with EPDM O-ring with PTFE coated spring + EPDM O-rings with PTFE coated spring + FPM O-rings
45 CECK VALVES Knocker Tee Cemented d I Z I Cod d l Z Weight PN Pack
46 FOOT VALVES Foot Valve Cemented X00 Cod d DN l Z F K Weight PN Pack 116X X X X X X X X X X with EPDM O-ring with FPM O-ring Foot Valve X10 Cod G DN Lt Z F K Weight PN Pack 116X / X / X / X X / X / X X / X X with EPDM O-ring with FPM O-ring
47 AIR RELEASE VALVES Air Release Valve Cemented X00 Cod d DN l Z F K Weight PN Pack 116X X X X X X X X X X with EPDM O-ring with FPM O-ring Air Release Valve X10 Cod G DN Lt Z F K Weight PN Pack 116X / X / X / X X / X / X X / X X with EPDM O-ring with FPM O-ring
48 VALVES ACCESSORIES Valve End Cemented Cod d K l Weight PN Valve End Cod G K Lt Weight PN / / / / / /
49 VALVES ACCESSORIES Blue andle Cod d E L L1 L2 Weight / ,15 61,7 24,2 37,5 11, / ,15 61,7 24,2 37,5 11, / , ,5 42, , , ,5 20, / , ,4 56, / ,9 107, ,8 38, , ,6 77,3 60, /2 45, ,8 54,9 77,9 77, ,2 42,9 152, ,7 117, ,5 47,3 185,7 75,9 109,1 168, Red andle Cod d E L L1 L2 Weight / ,15 61,7 24,2 37,5 11, / ,15 61,7 24,2 37,5 11, / , ,5 42, , , ,5 20, / , ,4 56, / ,9 107, ,8 38, , ,6 77,3 60, /2 45, ,8 54,9 77,9 77, ,2 42,9 152, ,7 117, ,5 47,3 185,7 75,9 109,1 168,8 49
50 VALVES ACCESSORIES Valve Nut Cod G E E1 Weight PN / / / / / / PE End Connector h K d l Cod d K h I W Weight * * * * DELIVERY PROGRAM 50
51 VALVES ACCESSORIES Set of 0-Rings 115 / 125 / 128 / 135 / 134 O-Ring For Stem valve code /1 Ø valve code /1 Ø valve code /1 Ø valve code Ø valve code Ø set 115 set 125 set 135 set 135 set 134 valve code /1 Ø valve code /1 Ø * valve code /1 Ø valve code Ø valve code Ø valve code Ø set 125 set 128 set 134 set 134 set 134 set /8" 20-1/2" 25-3/4" 32-1" 40-11/4" 50-11/2" 63-2" 75-21/2" 90-3" 110-4" Type ,2x1, ,2x1, ,5x ,11x1, ,78x2, ,95x2, ,04x3, ,64x3, ,82x3, ,8x3,53 O-Ring For Spacing Normal Support Valve code /1 Valve code /1 Valve code set 115 set 135 set 135 Support Valve code /1 Valve code /1 Valve code *112700/1 Valve code Valve code Valve code Valve code set 125 set 125 set 128 set 134 set 134 set 134 set /8" 20-1/2" 25-3/4" 32-1" 40-11/4" 50-11/2" 63-2" 75-21/2" 90-3" 110-4" Type ,72x2,62 Type ,5x1,5 Type ,23x2,62 Type ,23x2,62 Type 5 PTFE020 15x21x ,72x2, ,5x1, ,23x2, ,23x2,62 PTFE020 15x21x ,07x2, ,52x1, ,83x2, ,83x2,62 PTFE025 20x27x3, ,75x3, ,87x1, ,7x3, ,17x2,62 PTFE032 25x33x ,7x3, ,17x2, ,62x3, ,7x2,62 PTFE040 32x42x x5, ,7,2, ,15x3, ,42x2,62 PTFE050 40x51x5, ,7x5, ,42x2, ,63x3, ,63x3,53 PTFE063 50x63x6, ,92x5, ,62x3, ,67x3,53 PTFE075 65x82x ,79x5, ,5x3, ,7x5, ,48x5, ,5x3, ,9x5,34 PTFE090 PTFE110 80,5x95,6x7,5 100,5x116x9 O-Ring For Body Only for compression side valves 16-3/8" 20-1/2" 25-3/4" 32-1" 40-11/4" 50-11/2" 63-2" 75-21/2" 90-3" 110-4" Type 1 Type ,72x2, ,5x1, ,72x2, ,5x1, ,07x2, ,52x1, ,75x3, ,87x1, ,7x3, ,17x2, x5, ,7,2, ,7x5, ,42x2, ,92x5, ,62x3, ,79x5, ,5x3, ,48x5, ,5x3,53 Type PTFE020 Type 5 15x21x3 * Set of FPM O-Rings PTFE020 15x21x3 PTFE025 20x27x3,5 PTFE032 25x33x4 PTFE040 32x42x5 PTFE050 40x51x5,5 PTFE063 50x63x6,5 PTFE075 65x82x6 PTFE090 PTFE110 80,5x95,6x7,5 100,5x116x9 51
52 VALVES ACCESSORIES CECK - FOOT - AIR - RELEASE VALVES Set of 0-Rings *100 / 106 Gasket For Piston valve code /1 Ø valve code /1 Ø valve code /1 Ø * valve code /1 Ø * valve code /1 Ø valve code /1 Ø * valve code /1 Ø valve code /1 Ø * 16-3/8" 20-1/2" 25-3/4" 32-1" 40-11/4" 50-11/2" 63-2" 75-21/2" 90-3" 110-4" Type 1 *GP020V 12,5x20x2 *GP020V 12,5x20x2 *GP025V 17x24x2 *GP032V 22x32x2 *GP040V 38x28x3 *GP050V 51x35x4 *GP063V 58x42x4 *GP075V 57x77x4 *GP090V 72x93x4 *GP090V 110x90x4 O-Ring For Spacing Normal Support 16-3/8" 20-1/2" 25-3/4" 32-1" 40-11/4" 50-11/2" 63-2" 75-21/2" 90-3" 110-4" Type ,23x2,62 Type ,72x2, ,23x2, ,72x2, ,83x2, ,07x2, ,17x2, ,75x3, ,7x2, ,7x3, ,42x2, x5, ,63x3, ,7x5, ,67x3, ,92x5, ,7x5, ,79x5, ,47x3, ,48x5,34 O-Ring For Body 16-3/8" 20-1/2" 25-3/4" 32-1" 40-11/4" 50-11/2" 63-2" 75-21/2" 90-3" 110-4" Type ,72x2, ,72x2, ,07x2, ,75x3, ,7x3, x5, ,7x5, ,92x5, ,79x5, ,48x5,34 Spring Stainiess steel 316 core Spring Teflon coated onstanless steel 316 core Spring 16-3/8" 20-1/2" 25-3/4" 32-1" 40-11/4" 50-11/2" 63-2" 75-21/2" 90-3" 110-4" 52 Type 4 ML020 ML020 ML025 ML032 ML040 ML050 ML063 ML075 ML090 ML110 * Set of FPM O-Rings
53 TECNICAL SPECIFICATIONS - FITTINGS Product Description DESCRIPTION Precision moulded pressure pipe fittings and flanges made from PVC-U250 suitable for PVC pipe systems up to 16 bar. Our comprehensive range of items and sizes can be joined either by cold solvent cementing or through threading. Sizes and dimensions conform to international standard. All fittings are suitable for potable water, beverges, and food contact, as well as corrosive* fluid transports. * For specific chemicals, please consult your sales rep. STANDARDS Products conform to the requirments of ISO 264, 727, 2536, 3460, KIWA Criteria Std. Nr. 54 and DIN 8063, 19532, UNI EN , AFNOR and MATERIALS PVC-U250 unplasticized poly (vinyl chloride) meeting the above mentioned Standards. Injection-moulded components: PVC-U250. Metal reinforced rings: on the female threads INOX AISI 430. Gaskets and O-Rings: EPDM. MARKINGS The fittings and valves incorporate the following information moulded in relief: - PLASSON Trade Mark (registered in most countries) - Diameter of connection - Nominal pressure - Type of Material COLOUR All fittings and valves are grey, in accordance with PVC-U pressure pipeline standards. ITEMS Sockets, 45o and 90o Elbows, 90o Tees, Bushes, Unions, Reducers, Adaptors, ose Nozzles, Caps, Plugs, Nipples, Flanges, Flange Adaptors, Ball Valves, Foot Valves, Check Valves, and Air Release Valves. SANITARY LAWS The PLASSON fittings and valves conform to the sanitary laws and regulations in force in the various European Countries and in the U.S. relating to transportation of potable water, wine, beverages and food. APPLICATION FIELDS Potable water systems, irrigation systems (including fertilization), installation for wine, beer, beverages and other fluids, industrial plants, conveyence of acids, bases, salts, fresh or swimming water, ship installations. (for special installations, please contact your Plasson supplier). JOINTING TYPES The fittings and the valves are available with three types of connections: Plain ends for solvent cement jointing to pressure pipes of metric dimensions. Fourth digit in the catalogue no. is O (XXXO). ends to be screwed onto BSP threaded pipes/ fittings. Fourth digit in the catalogue no. is 1 (XXX1). A combination of ends ( adaptor fittings ) suitable for joining a PVC pipeline of the metric dimensions to a BSP threaded pipe, fitting, valve or accessory (PVC or other materials). Fourth digit in the catalogue no. is 2 (XXX2). SIZES For standard pipes of the ISO metrical range: 12, 16, 20, 25, 32, 40, 50, 63, 75, 90, 110, 125, 140, 160, 200, 225mm. And for pipes of the BSP threaded range: 1/4, 3/8, 1/2, 3/4, 1, 11/4, 11/2, 2, 21/4, 3, 4,5. TREADS PLASSON fittings are female threaded (cylindrical) and male threaded (conical) in accordance with ISO, BS 21, and UNI 339 standards. FLANGES PLASSON backing flanges are to be used in connection with the flange adaptors (catalogue no. 5500, 5510, and 5520). The number, sizes and distance between the centre of the holes conform to UNI 2223, EN , ISO 2536 and DIN 8063 for pressure classes of Bar. ACCESSORIES The fitting range is completed by some accessories such as solvent cement, primer, PTFE tape, etc. WORKING TEMPERATURES CELSIUS PFA* (PN) Bar 16 14,4 12,8 11,2 10 PFA* (PN) Bar ,25 * in accordance with EN 805 PRESSURES The fittings and valves, in accordance with EN 805 standard, have three working pressures: PTA (PA), PMA and PEA. To every PFA values are connected the following PMA and PEA: PRESSURES IN BAR PFA -PA PMA PEA , ,5 9 53
54 TECNICAL SPECIFICATIONS - FITTINGS Product Description PVC PROPERTIES The following are the required properties for injection moulded PVC-U250 fittings and valves in accordance with ISO-EN-UNI Standards: CARACTERISTICS UNITS VALUES STANDARDS Density at 23 C Kg/dm ISO 1183 Vicat 5 Kg. o C 77 ISO 306 Tensile impact strength KJ/m ISO 527 Tensile strength at break MPa 49 ISO 527 Elongation at break % 120 ISO 527 Yield stress MPa 46 ISO 527 Flexural modulus MPa 3000 ISO 527 eat conductivity at 23 o C W/mK 0,13-0,19 ASTM C 177 Specific heat at 23 o C J/Kg K Fire resistance (0,85 mm.) V 0 UL 94 Permissable working pressures in accordance with DIN SYMBOLS & DEFINITIONS FITTINGS PN - Nominal Pressure in Bar - Allowable operating pressure conveying water at 20OC during 50 years. PFA - Allowable Operating Pressure - Maximum hydrostatic pressure that a component is capable of withstanding continuously in service (EN 805:1999); for water at temperatures up to 25OC: PFA=PN. PMA - Allowable Maximum Operating Pressure - Maximum pressure occurring from time to time, including surge, that a component is capable of withstanding in service (EN 805:1999). PEA - Allowable Site Test Pressure - Maximum hydrostatic pressure that a newly installed component is capable of withstanding for a relatively short duration, in order to ensure the integrity and tightness of the pipeline (EN 805:1999). MRS: Minimum Required Strength PVC-U: Unplasticized Poly (vinyl chloride) Pressure in bars Time in years 10 C 20 C 30 C 40 C 50 C 60 C PVC-U250: Unplasticized Poly (vinyl chloride) material for injectionmoulded components, such as PLASSON fittings and valves, with a proved MRS-value of at least 25Mpa. EPDM: Ethylene Propylene Rubber FPM: Fluoride Rubber (VITON) PTFE: Polytetrafluoroethylene ABBREVIATIONS USED IN TIS CATALOGUE d, d 1 Nominal inside diameter G, G 1 Nominal size of thread in inches DN Nominal bore D, D 1 Outside diameter E, E 1 Maximum overall external diameter 1, 1 1 Internal length of cementing L, L 1, L 2 External length for cementing Lt, Lt 1 Length of thread Z Length from pipe stop to centre/other pipe stop C External size of octagon B Length of rim Dp Pitch circle diameter of bolt holes in flanges S Diameter of bolt holes in flanges N Number of bolt holes in flange e Cross section diameter of O-Ring Total length W Weight in grams 54
55 TECNICAL SPECIFICATIONS - VALVES Product Description DESCRIPTION Precision moulded valves made from upvc suitable for line pipe systems up to 16 bar. Our comprehensive range of items and sizes can be connected either by cold solvent cementing or through threading. Sizes and dimensions conform to international standards. All valves are suitable for potable water, beverages, food as well as corrosive fluid transport. MATERIALS PVC-U250 (unplasticized polyvinyl chloride) meeting the standards of DIN-BS-UNI-AFNOR, KIWA, etc O-Rings 1) EPDM (ethylene-propylene copolymer). ardness: 70 shore, unless otherwise specified 2) FPM (Fluorised-Rubber) ardness: 70 shore, unless otherwise specified Springs 1) PTFE coated stainless steel 316 core 2) Coated Springs: Teflon coated on stainless steel 316 core Gaskets (on ball) 1) PTFE (Polytetra Fluorised-Ethylene) 2) PE MARKINGS The valves incorporate the following information moulded in relief: Plasson Trade Mark (registered in most countries) Diameter of connection Nominal pressure Type of Material COLOUR All valves are grey, in accordance with PVC-U pressure pipeline standards. andles are blue or red. ITEMS Ball Valves, Check Valves, Foot Valves, Air Release Valves SANITARY LAWS The PLASSON valves conform to the sanitary laws and regulations in force in the various European Countries and in the U.S. relating to transportation of potable water, wine, beverages and food. APPLICATION FIELDS Potable water systems, irrigation systems (including fertilization), installation for wine, beer, beverages and other fluids, industrial plants, conveyence of acids, bases, salts, fresh or swimming water pool, ship installlations. (for special installations, please contact your Plasson supplier). JOINTING TYPES The valves are available with three types of connections: Plain ends for solvent cement jointing to pressure pipes of metric dimensions. Fourth digit in the catalogue no. is O (XXXO). ends to be screwed onto BSP threaded pipes/ fittings. Fourth digit in the catalogue no. is 1 (XXX1). SIZES For standard pipes of the ISO metrical range of mm: 16, 20, 25, 32, 40, 50, 63, 75, 90, 110 And for pipes of the BSP threaded range: 3/8, 1/2, 3/4, 1, 1 1/4, 1 1/2, 2, 2 1/2, 3 TREADS PLASSON valves are female threaded (cylindrical) and male threaded (conical) according with ISO 7, UNI 339, DIN 2999 and BS 21 standards. MECANICAL PROPERTIES Maximum working pressure in bars: Δ16-63: PN16 Δ75-110: PN10 Minumun pressure KNOCKER TEE: 0,2bar Minumun opening pressure Check Valves: 0,5bar PVC PROPERTIES The following are the required properties for an injection moulded PVC fittings withstanding pressures PN16 in accordance with UNI standards: CARACTERISTICS UNITS VALUES STANDARDS Density Kg/m ISO 1183 Vicat (50N) o C 76 ISO 306-B Yield stress MPa 45 ISO 527 Tensile Strength at break (23 0 ) MPa 40 ISO 527 Elongation at break % 120 ISO 527 Tensile Modulus MPa 3000 ISO 527 Unnotched j/m Notched j/m IZOD Impact ASTM 23 o C NB 270 Strength D256 0 o C NB 150 ISO180 0 o C < Permissable working pressures in accordance with DIN8062 Pressure in bars Time in years 10 C 20 C 30 C 40 C 50 C 60 C 55
56 TECNICAL SPECIFICATIONS - VALVES Product Description ABBREVIATIONS USED IN TIS CATALOGUE d F G J K DN D I L Lp Lt Z W Nominal inside diameter Distance from centre of valve to top of handle or valve Nominal size of thread in inches Length of handle Outside diameter or nut Nominal bore corresponding approx to the inside diameter of the pipe Outside diameter Internal length for cementing External length for cementing Internal length to PE pipe Length of thread Length from pipe stop to centre/other pipe stop Total length Weight in grams SYMBOLS & DEFINITIONS FITTINGS PN - Nominal Pressure in Bar - Allowable operating pressure conveying water at 20OC during 50 years. PFA - Allowable Operating Pressure - Maximum hydrostatic pressure that a component is capable of withstanding continuously in service (EN 805:1999); for water at temperatures up to 25OC: PFA=PN. PMA - Allowable Maximum Operating Pressure - Maximum pressure occurring from time to time, including surge, that a component is capable of withstanding in service (EN 805:1999). PEA - Allowable Site Test Pressure - Maximum hydrostatic pressure that a newly installed component is capable of withstanding for a relatively short duration, in order to ensure the integrity and tightness of the pipeline (EN 805:1999). MRS: Minimum Required Strength PVC-U: Unplasticized Poly (vinyl chloride) PVC-U250: Unplasticized Poly (vinyl chloride) material for injectionmoulded components, such as PLASSON fittings and valves, with a proved MRS-value of at least 25Mpa. EPDM: Ethylene Propylene Rubber FPM: Fluoride Rubber (VITON) PTFE: Polytetrafluoroethylene 56
57 ASSEMBLY INSTRUCTIONS Normal Support Instructions for connection to the system - A) Completely unscrew the ring nuts (12) and fit them to the pipe that the valve is to be connected to. B) Either glue or screw couplings (10) at the pipe ends. C) Position the valve body (5) between the two couplings. D) Lock the ring nuts for both sides. Instructions for disassembling and reassemble - Completely unscrew the ring nuts (12). Remove the valve body (5) radially. Remove the handle (1) by pulling upwards. Release the gasket support (8) by pushing the ball (4) through the valve while the valve is closed. Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFE gasket (7*) using a suitable tool in order to prevent damage. Remove the ball (4) which was previously positioned during the closing phase. Remove the stem (3) by pushing downwards and extracting it from inside the valve body. Remove the O-Ring (2*) from the stem (3) using a suitable tool. Remove the O-Ring (9*) and the PTFE gasket (7*) using a suitable tool. To assemble the valve, follow the same procedure in the opposite sequence. Notes: The valve shall be supplied with a pre-set radial seal, applicable to average operating conditions; due to particular operating conditions, it might be necessary to turn clockwise or anticlockwise the ring nuts (12) from the side of the gasket support (8) Instructions for connection to the system - A) Completely unscrew the ring nut (12) and fit it to the pipe that the valve is to be connected to. B) Either glue or screw fixed side (5) to the pipe end. C) Either glue or screw coupling (10) to the pipe end. D) Lock the ring nut. Instructions for disassembling and reassemble - Completely unscrew the ring nut (12). Remove the valve body (5) radially. Remove the handle (1) by pulling upwards. Release the gasket support (8) by pushing the ball (4) through the valve while the valve is closed. Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFE gasket (7*) using a suitable tool in order to prevent damage. Remove the ball (4) which was previously positioned during the closing phase. Remove the stem (3) by pushing downwards and extracting it from inside the valve body. Remove the O-Ring (2*) from the stem (3) using a suitable tool. Remove the O-Ring (9*) and the PTFE gasket (7*) using a suitable tool. To assemble the valve, follow the same procedure in the opposite sequence. Notes: The valve shall be supplied with a pre-set radial seal, applicable to average operating conditions; due to particular operating conditions, it might be necessary to turn clockwise or anticlockwise the ring nut (12) Instructions for connection to the system - A) Completely unscrew the ring nut (12) and fit it to the pipe that the valve is to be connected to. B) Screw fixed side (5) to the pipe end. C) Screw coupling (10) to the pipe end. D) Lock the ring nut. Instructions for disassembling and reassemble - Completely unscrew the ring nut (12). Remove the valve body (5) radially. Remove the handle (1) by pulling upwards. Release the gasket support (8) by pushing the ball (4) through the valve while the valve is closed. Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFE gasket (7*) using a suitable tool in order to prevent damage. Remove the ball (4) which was previously positioned during the closing phase. Remove the stem (3) by pushing downwards and extracting it from inside the valve body. Remove the O-Ring (2*) from the stem (3) using a suitable tool. Remove the O-Ring (9*) and the PTFE gasket (7*) using a suitable tool. To assemble the valve, follow the same procedure in the opposite sequence. Notes: The valve shall be supplied with a pre-set radial seal, applicable to average operating conditions; due to particular operating conditions, it might be necessary to turn clockwise or anticlockwise the ring nut (12). 57
58 ASSEMBLY INSTRUCTIONS Support Instructions for connection to the system - A) Completely unscrew the ring nuts (12) and fit them to the pipe that the valve is to be connected to. B) Either glue or screw couplings (10) at the pipe ends. C) Position the valve body (5) between the two couplings. D) Lock the ring nuts for both sides. Instructions for disassembling and reassemble - Completely unscrew the ring nuts (12). Completely unscrew the ring nuts (12). Remove the valve body (5) radially. Remove the handle (1) by pulling upwards. Insert the key in its seat in the gasket support (8). Completely unscrew the gasket support (8) by rotating the handle anticlockwise. Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFE gasket (7*) using a suitable tool in order to prevent damage. Remove the ball (4) which was previously positioned during the closing phase. Remove the stem (3) by pushing downwards and extracting it from inside the valve body. Remove the O-Ring (2*) from the stem (3) using a suitable tool. Remove the O-Ring (9*) and the PTFE gasket (7*) using a suitable tool. To assemble the valve, follow the same procedure in the opposite sequence. Notes: The valve shall be supplied with a pre-set radial seal, applicable to average operating conditions; due to particular operating conditions, it might be necessary to follow the instructions below before performing the final step: 1. Disconnected the handle (1) by pulling upwards. 2. Insert the key in its seat in the gasket support (8). 3. Turn clockwise or anticlockwise to adjust as required Instructions for connection to the system - A) Completely unscrew the ring nuts (12) and fit them to the pipe that the valve is to be connected to. B) Either glue or screw couplings (10) at the pipe ends. C) Position the valve body (5) between the two couplings. D) Lock the ring nuts for both sides. Remove the ball (4) which was previously positioned during the closing phase. Remove the stem (3) by pushing downwards and extracting it from inside the valve body. Remove the O-Ring (2*) from the stem (3) using a suitable tool. Remove the O-Ring (9*) and the PTFE gasket (7*) using a suitable tool. To assemble the valve, follow the same procedure in the opposite sequence Instructions for disassembling and reassemble - Completely unscrew the ring nuts (12). Remove the valve body (5) radially. Remove the handle (1) by pulling upwards. Insert the key in its seat in the gasket support (8). Completely unscrew the gasket support (8) by rotating the handle anticlockwise. Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFE gasket (7*) using a suitable tool in order to prevent damage. Notes: The valve shall be supplied with a pre-set radial seal, applicable to average operating conditions; due to particular operating conditions, it might be necessary to follow the instructions below before performing the final step: 1. Disconnected the handle (1) by pulling upwards. 2. Insert the key in its seat in the gasket support (8). 3. Turn clockwise or anticlockwise to adjust as required. 58
59 ASSEMBLY INSTRUCTIONS Support Instructions for connection to the system - A) Completely unscrew the ring nut (12) and fit it to the pipe that the valve is to be connected to. B) Either glue or screw fixed side (5) to the pipe end. C) Either glue or screw coupling (10) to the pipe end. D) Lock the ring nut. Instructions for disassembling and reassemble - Completely unscrew the ring nut (12). Remove the valve body (5) radially. Remove the handle (1) by pulling upwards. Insert the key in its seat in the gasket support (8). Completely unscrew the gasket support (8) by rotating the handle anticlockwise. Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFE gasket (7*) using a suitable tool in order to prevent damage. Remove the ball (4) which was previously positioned during the closing phase. Remove the stem (3) by pushing downwards and extracting it from inside the valve body. Remove the O-Ring (2*) from the stem (3) using a suitable tool. Remove the O-Ring (9*) and the PTFE gasket (7*) using a suitable tool. To assemble the valve, follow the same procedure in the opposite sequence. Notes: The valve shall be supplied with a pre-set radial seal, applicable to average operating conditions; due to particular operating conditions, it might be necessary to follow the instructions below before performing the final step: 1. Disconnected the handle (1) by pulling upwards. 2. Insert the key in its seat in the gasket support (8). 3. Turn clockwise or anticlockwise to adjust as required Instructions for connection to the system - A) Completely unscrew the ring nut (12) and fit it to the pipe that the valve is to be connected to. B) Screw fixed side (5) to the pipe end. C) Screw coupling (10) to the pipe end. D) Lock the ring nut. Instructions for disassembling and reassemble - Completely unscrew the ring nut (12). Remove the valve body (5) radially. Remove the handle (1) by pulling upwards. Insert the key in its seat in the gasket support (8). Completely unscrew the gasket support (8) by rotating the handle anticlockwise. Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFE gasket (7*) using a suitable tool in order to prevent damage. Remove the ball (4) which was previously positioned during the closing phase. Remove the stem (3) by pushing downwards and extracting it from inside the valve body. Remove the O-Ring (2*) from the stem (3) using a suitable tool. Remove the O-Ring (9*) and the PTFE gasket (7*) using a suitable tool. To assemble the valve, follow the same procedure in the opposite sequence. Notes: The valve shall be supplied with a pre-set radial seal, applicable to average operating conditions; due to particular operating conditions, it might be necessary to follow the instructions below before performing the final step: 1. Disconnected the handle (1) by pulling upwards. 2. Insert the key in its seat in the gasket support (8). 3. Turn clockwise or anticlockwise to adjust as required. 59
60 ASSEMBLY INSTRUCTIONS Support Instructions for connection to the system - A) Connect PE pipe to the compression nut (19). B) Completely unscrew the ring nuts (12) and fit them to the pipe that the valve is to be connected to. C) Either glue or screw couplings (10) at the pipe ends. D) Position the valve body (5) between the two couplings. E) Lock the ring nuts for both sides. Instructions for disassembling and reassemble - Completely unscrew the ring nuts (12). Remove the valve body (5) radially. Remove the handle (1) by pulling upwards. Insert the key in its seat in the gasket support (8). Completely unscrew the gasket support (8) by rotating the handle anticlockwise. Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFE gasket (7*) using a suitable tool in order to prevent damage. Remove the ball (4) which was previously positioned during the closing phase. Remove the stem (3) by pushing downwards and extracting it from inside the valve body. Remove the O-Ring (2*) from the stem (3) using a suitable tool. Remove the O-Ring (9*) and the PTFE gasket (7*) using a suitable tool. To assemble the valve, follow the same procedure in the opposite sequence. Notes: The valve shall be supplied with a pre-set radial seal, applicable to average operating conditions; due to particular operating conditions, it might be necessary to follow the instructions below before performing the final step: 1. Disconnected the handle (1) by pulling upwards. 2. Insert the key in its seat in the gasket support (8). 3. Turn clockwise or anticlockwise to adjust as required. 60
61 1 ASSEMBLY INSTRUCTIONS Support Instructions for connection to the system - A) Completely unscrew the ring nuts (12) and fit them to the pipe that the valve is to be connected to. B) Either connect to the compression fittings or electrofuse or butt weld PE spigots (20) at the pipe ends. C) Position the valve body (5) between the two couplings. D) Lock the ring nuts for both sides. Instructions for disassembling and reassemble - Completely unscrew the ring nuts (12). Remove the valve body (5) radially. Remove the handle (1) by pulling upwards. Insert the key in its seat in the gasket support (8). Completely unscrew the gasket support (8) by rotating the handle anticlockwise. Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFE gasket (7*) using a suitable tool in order to prevent damage. Remove the ball (4) which was previously positioned during the closing phase. Remove the stem (3) by pushing downwards and extracting it from inside the valve body. Remove the O-Ring (2*) from the stem (3) using a suitable tool. Remove the O-Ring (9*) and the PTFE gasket (7*) using a suitable tool. To assemble the valve, follow the same procedure in the opposite sequence. Notes: The valve shall be supplied with a pre-set radial seal, applicable to average operating conditions; due to particular operating conditions, it might be necessary to follow the instructions below before performing the final step: 1. Disconnected the handle (1) by pulling upwards. 2. Insert the key in its seat in the gasket support (8). 3. Turn clockwise or anticlockwise to adjust as required Instructions for connection to the system - A) Connect PE pipe to the compression nut (19). B) Completely unscrew the ring nuts (12) and fit them to the pipe that the valve is to be connected to. C) Either connect to the compression fittings or electrofuse or butt weld the PE spigots (20) at the pipe ends. D) Position the valve body (5) between the two couplings. E) Lock the ring nuts for both sides. Instructions for disassembling and reassemble - Completely unscrew the ring nuts (12). Remove the valve body (5) radially. Remove the handle (1) by pulling upwards. Insert the key in its seat in the gasket support (8). Completely unscrew the gasket support (8) by rotating the handle anticlockwise. Remove O-Rings (6*, 9*, 11*) from gasket support (8) and PTFE gasket (7*) using a suitable tool in order to prevent damage. Remove the ball (4) which was previously positioned during the closing phase. Remove the stem (3) by pushing downwards and extracting it from inside the valve body. Remove the O-Ring (2*) from the stem (3) using a suitable tool. Remove the O-Ring (9*) and the PTFE gasket (7*) using a suitable tool. To assemble the valve, follow the same procedure in the opposite sequence. Notes: The valve shall be supplied with a pre-set radial seal, applicable to average operating conditions; due to particular operating conditions, it might be necessary to follow the instructions below before performing the final step: 1. Disconnected the handle (1) by pulling upwards. 2. Insert the key in its seat in the gasket support (8). 3. Turn clockwise or anticlockwise to adjust as required. 61
62 ASSEMBLY INSTRUCTIONS Check Valves Instructions for connection to the system - A) Completely unscrew the ring nuts (12) and fit them to the pipe that the valve is to be connected to. B) Either glue or screw couplings (10) at the pipe ends. C) Position the valve body (5) between the two couplings. D) Lock the ring nuts for both sides. and the spring assisted piston (15) does not fall out. Remove the the spring assisted piston (15). To replace valve reverse the procedure being careful to set the O-Ring properly and grease it with silicon grease Instructions for disassembling and reassemble - Completely unscrew the ring nuts (12). Remove the valve body (13) radially. Release the gasket support (16) by pushing it and making sure that the spring (17) Instructions for connection to the system - A) Completely unscrew the ring nuts (12) and fit them to the pipe that the valve is to be connected to. B) Either glue or screw couplings (10) at the pipe ends. C) Position the valve body (5) between the two couplings. D) Lock the ring nuts for both sides. pushing it. Remove the the spring assisted piston (15). To replace valve reverse the procedure being careful to set the O-Ring properly and grease it with silicon grease. Instructions for disassembling and reassemble - Completely unscrew the ring nuts (12). Remove the valve body (13) radially. Release the gasket support (16) by Instructions for connection to the system - A) Completely unscrew the ring nuts (12) and fit them to the pipe that the valve is to be connected to. B) Either glue or screw couplings (10) at the pipe ends. C) Position the valve body (5) between the two couplings. D) Lock the ring nuts for both sides. pushing it. Remove the the spring assisted piston (15). To replace valve reverse the procedure being careful to set the O-Ring properly and grease it with silicon grease. Instructions for disassembling and reassemble - Completely unscrew the ring nuts (12). Remove the valve body (13) radially. Release the gasket support (16) by 62
63 CERTIFICATION NAVAL APPLICATION Società Certificata UNI EN ISO 9100/
64 Via Gallinea, Mele (GE) Italy Tel Fax Edition 06/2016
VERSION 3. PVC FITTINGS & VALVES Technical Catalogue
VERSION 3 PVC FITTINGS & VALVES Technical Catalogue INTRODUCTION Plasson s innovative products revolutionized the way of connecting polyethylene pipes in the 1960 s. We started with fittings for agricultural
More informationPVC FITTINGS & VALVES
PVC FITTINGS & VALVS Technical Catalogue Distributor of 1 Introuction Plasson s innovative proucts revolutionize the way of connecting polyethylene pipes in the 1960 s. We starte with fittings for agricultural
More informationstandard and industrial pipe fittings
fittings mm sizes standard and industrial pipe fittings Photo: Chlor Generators Ltd Available in a wide range of mm sizes from 10mm to 500mm, and in a choice of pressure ratings from 6 bars to 16 bars,
More informationindustrial and economy pipe fittings PVC-U Solvent Cement WELD-ON REGULAR 719 Size Code Price 500ml tin
pvcu fittings mm sizes industrial and economy pipe fittings fittings mm sizes 68 Photo: Chlor Generators Ltd Available in a wide range of mm sizes from 10mm to 500mm, and in a choice of pressure ratings
More informationMARCH Polyethylene Piping Systems.
MARCH 2017 Polyethylene Piping Systems www.plasson.com.au GLOBAL PRESENCE LOCAL COMMITMENT Get an expert on your team. Plasson has the widest range of compression, electrofusion, threaded and transitional
More informationJULY Polyethylene Piping Systems.
JULY 205 Polyethylene Piping Systems www.plasson.com.au GLOBAL PRESENCE LOCAL COMMITMENT Get an expert on your team. Plasson has the widest range of compression, electrofusion, threaded and transitional
More informationABS Pipe metric system Plain PN10
S Pipe metric system Plain PN10 t (mean) Da (min) Size Thickness Weight Length ode t Da mm kg/m m 16 1.5 0.07 3 11 565 305 20 1.6 0.10 3 11 565 306 25 1.9 0.14 3 11 565 307 35 2.1 0.21 3 11 565 308 16
More informationFITTINGS PP-H. Fittings, metric series ISO-UNI
FITTINGS for socket welding PP-H Fittings, metric series ISO-UNI FITTINGS for socket welding Series of fittings designed for conveying fluids under pressure with a hot weld connection system (socket welding).
More informationPRICE LIST E9.17 PVC-U LARGE BORE PRESSURE FITTINGS
PRICE LIST E9.17 PVC-U LARGE BORE PRESSURE FITTINGS Since 1954 FIP produces injection moulded valves and fittings in thermoplastic materials for pressure pipeline systems thus becoming nowadays the largest
More informationChapter 1 Pipes and fittings PVC - PE
Chapter 1 Pipes and fittings PVC - PE Solvent weld fittings Threaded connections Ball valves & butterfly valves Page 1-20 Page 21-33 Page 34-37 Slide valves & check valves Solvents & sealants Tools Page
More informationSECTIO N 15 Phone: (866) Fax: (888)
PVC FITTINGS SCHEDULE 40, 80, INSERT NYLON FITTINGS PVC & CPVC NIPPLES SECTIO N 15 www.cbsupplies.ca Phone: (866) 503-5523 Fax: (888) 562-2095 AGI@cbsupplies.ca PRODUCTS LIST SCHEDULE 40 PVC PRESSURE FITTINGS
More informationRapid push-in fittings for plastic tubes Series 1000
CATALOGUE > Release 8.5 > Rapid fittings Series 1000 Rapid push-in fittings for plastic tubes Series 1000 Tube external diameters: 5/3, 6/, 8/6, 10/8, 12/10, 15/12,5 mm Fittings threads: metric (M5, M6,
More information3 way ball valve S4 hand operated
General: Symbolfoto Material: PVC-U / PP / PVDF Sealing material: EPDM / FPM Ball seating joint: PTFE Ball: T- oder L-Bohrung Dimensions: DN0 (DN5 / d6 / d/8 ) DN5 d0 d/ DN0 (DN5 / d5 / d/4 ) DN5 d d DN
More informationISO-BSP FITTINGS PVC-C. TemperFIP100 adapter fittings
ISO-BSP FITTINGS PVC-C TemperFIP100 adapter fittings FITTINGS ISO-BSP Series of fittings designed for conveying fluids under pressure with threaded and cold chemical solvent weld jointing systems (solvent
More informationFITTINGS PVDF. Fittings, metric series ISO-UNI
FITTINGS for socket welding PVDF Fittings, metric series ISO-UNI FITTINGS for socket welding Series of fittings designed for conveying fluids under pressure with a hot weld connection system (socket welding)
More informationISO-BSP FITTINGS PVC-U. Adaptor fittings
ISO-BSP FITTINGS PVC-U Adaptor fittings FITTINGS ISO-BSP Series of fittings designed for conveying fluids under pressure with threaded and solvent weld cold chemical jointing systems (solvent welding)
More informationPipe Nipples / Solvent Cement / Pipe Clips 11. Diaphragm Valves / Knife Gate Valves 21
TABLE OF CONTENTS Pipe Sizing 1 Pipe 2 Tee s 3 Elbows 4 Couplings 5 Adaptors, Caps & Plugs 6 Unions 7 Reducer Bushing 8 Wye s / Clamp on Saddles 9 Flanges 10 Pipe Nipples / Solvent Cement / Pipe Clips
More informationSpears Low-Extractable SCHEDULE 80 PIPE
Spears Low-Extractable SCHEDULE 80 PIPE NOMINAL PIPE MAX. W.P. LGTHS/ PART NUMBER AVG. OD AVG. ID MIN. WALL LBS/FT SIZE PSI* CARTONS 1/2" LXT-005.840.528.147 420.202 22 3/4" LXT-007 1.050.724.154 340.273
More informationCOPRAX RANGE PIPES AND FITTINGS IN POLYPROPYLENE COP-RANDOM COPRAX. Comércio e Indústria do Plástico, Lda. AV. 16 DE MAIO Z.I.
COPRAX Comércio e Indústria do Plástico, Lda. AV. 16 DE MAIO Z.I. OVAR 3880 102 OVAR - PORTUGAL T +351 256 579 480 F +351 256 579 489 export@coprax.com www.coprax.com PIPES AND FITTINGS IN POLYPROPYLENE
More informationHAWLE - ZAK System. the threadless, restraint jointing system HAWLE. MADE FOR GENERATIONS.
HAWLE - System the threadless, restraint jointing system HAWLE. MADE FOR GENERATIONS. HAWLE - System the threadless, restraint jointing system for service connections integrated in Pipe Saddles, Service
More informationpvc-c manual valves inch sizes manual valves inch sizes Spears True Union 2000 Industrial Ball Valve
pvc-c Spears True Union 2000 Industrial Ball Valve Description: In-line double union ball valve with lockable handle Maximum Fluid Pressure at 20 C: Sizes 1 /2 to 2-16 bar; sizes 2 1 /2 to 6-10 bar All
More informationabs section guide application guide standards and approvals
abs Acrylonitrile - Butadiene - Styrene (ABS) is a rigid pressure piping system renowned for its high impact strength and durability which combine to give exceptional toughness. It is suitable for use
More informationmanual valves inch sizes
Spears True Union 2000 Industrial Vented Ball Valve Description: In-line double union ball valve Maximum Fluid Pressure at 20 C: All sizes 1 /2 to 2-16 bar; sizes 2 1 /2 to 4-10 bar; all sizes flanged
More informationPLASTICA ALFA. Compression. Fittings. Pipe Saddles. For use. with. Polyethylene. Pipe PRODUCT CATALOGUE PROUDLY IMPORTED BY.
Compression PRODUCT CATALOGUE Fittings & Pipe Saddles For use with Polyethylene Pipe DPI Trading PROUDLY IMPORTED BY www.dpitrading.co.za www.incledon.co.za Technical Information Body: black polypropylene
More information2 way ball valve S4 with integrated Praher Labeling System
Praher Plastics Austria GmbH DB/EN/DEEN///33 Technische Änderungen vorbehalten! way ball valve S4 Symbol photo Safety locking handle system This document does not constitute a guarantee, it is for initial
More informationPlastic Pressure Systems Plastic Pressure Systems
Uniclass L71161:P71 CI/SfB TPL10-IND In6 February 2016 Plastic Pressure Systems Plastic Pressure Systems Plastic Pressure Systems TPL10-IND Trade List Polypipe Terrain New Hythe Business Park Trade List
More informationWafer Check Valve Type 012 PVC-U
novel valve design with conical sealing surface for highest requirements and long service life body disc reinforced EPDM / FPM gaskets DN40 / d50 / 1½'' DN200 / d225 / 8'' operating pressure max. 10 bar
More informationd z z Le Le Elbow d L mm equiv inch 110 Le r 1) z 5 2 5 5 8 2 1 51/2 210 2 1 6 2 0 7 2 272 8 0 0 5 9 8 291 2 10 375 0 0 11 3 73 78 355 1 5 93 0 511 675 531 0 7 1 0 8 625 6 25 95 653 710 1065 686 1 7 900
More information600, 630. Diaphragm Valve, Plastic
Diaphragm Valve, Plastic Construction The /630 pneumatically operated 2/2-way valves have a low maintenance piston actuator which can be controlled by inert gaseous media. They have an integral optical
More informationPolypipe Terrain. New Hythe Business Park. College Road. Aylesford. Kent ME20 7PJ. Tel: Fax:
Uniclass L71161:P71 CI/SfB EFFTM2 In6 February 2018 Plastic Pressure Systems Plastic Pressure Systems Plastic Pressure Systems EFFTM2 Technical Manual Polypipe Terrain New Hythe Business Park Technical
More informationIRECO FITTINGS IN BRASS SERIES - FOR PLASTIC PIPES FOR ISO PIPES FROM DIAMETER 20 TO 63
11/17 0800 DESCRIPTION The IRECO 800 series compression fittings with EPDM elastomer ring washer have been conceived, designed and manufactured for plastic piping used for transporting fluids under pressure.
More informationPressure Pipes & Fittings
Pressure Pipes & Fittings Description: UPVC and CPVC pipes for hot and cold water supply under pressure. Range: Metric series fromø16 up toø315 mm, Imperial series fromø1/2" up toø1". Pressure Rating:
More informationSCHEDULE 80 PVC PRESSURE FITTINGS L80P EFFECTIVE JULY 1, 2017 REVISED PRODUCTS PRICE LIST INCLUDES: SCHEDULE 80 PVC 1/4 TO 12
PRICE GROUP DESCRIPTION 02 SCH 80 PVC through 8 92 SCH 80 PVC 10" AND LARGER VB GASKET for FLANGE DISCOUNT MULTIPLIER PRODUCTS SCHEDULE 80 PVC PRESSURE FITTINGS INCLUDES: SCHEDULE 80 PVC 1/4 TO 12 L80P
More informationfor plastic tubes CONNECTION > Series 6000 super-rapid fittings GENERAL DATA Fitting with connecting tube Sprint
> Series 6000 super-rapid fittings CATALOGUE > Release 8.8 Series 6000 super-rapid fittings for plastic tubes Sprint Tube external diameters: 3,, 5, 6, 8, 10, 12, 1, 16 mm Fittings threads: metric (M3,
More informationModular valve block MVB 100/200
Modular valve block MVB 100/200 Nominal size DN 15 Nominal size 1/2 Nominal pressure PN 6 bar www.asv-stuebbe.com/produkte/armaturen Characteristics MVB 100 Ideal for realising dosing and distribution
More informationPLASTICA ALFA. Compression. Fittings. Pipe Saddles. For use. with. Polyethylene. Pipe. DPI Trading PRODUCT CATALOGUE PROUDLY IMPORTED BY
Compression PRODUCT CATALOGUE Fittings & Pipe Saddles For use with Polyethylene Pipe DPI Trading PROUDLY IMPORTED BY www.dpitrading.co.za www.incledon.co.za Technical Information Body: black polypropylene
More informationINSERTION Adaptor for analysis
INSERTION Adaptor for analysis Type can be combined with... Universal adaptor for type 8202 and 8222 ELEMENT s in pure, aggressive or contaminated liquids Adaptation into standard piping systems or conversion
More informationPraher S4 Ball Valve. manual valves. Materials. Sizes. Pressure Rating. Features. Connections. Valve Dimensions. Actuation.
Praher S4 Ball Valve Lockable Handle Tagging Point Valve Bracket Actuation Materials Body - PVDF Ball Seat - PTFE Seals - FPM Sizes 3/8-4 /16mm - 110mm Features Lockable Handle (Lock not supplied) True
More informationPraher S4 Ball Valve. manual valves. Materials. Sizes. Pressure Rating. Features. Connections. Valve Dimensions. Actuation.
Praher S4 Ball Valve Lockable Handle Tagging Point Valve Bracket Actuation Materials Body - PVDF Ball Seat - PTFE Seals - FPM Sizes 3/8" - 4"/16mm - 110mm Features Lockable Handle (Lock not supplied) True
More informationR677. Diaphragm Valve, Plastic
Diaphragm Valve, Plastic Construction All medium wetted parts, the bonnet and handwheel of the GEMÜ 2/2-way diaphragm valve are made of plastic. The low maintenance plastic bonnet has an ergonomically
More informationBRASS FITTINGS (R410a) BRASS FITTINGS
(R410a) R410a Short Barrel Flare Nuts 5010404410A 1/4 $4.21 5010808410A 1/2 $8.52 5010504410A 5/16fl x 1/4 tube $5.73 5011010410A 5/8 $13.50 5010606410A 3/8 $7.08 5011212410A 3/4 $20.54 BRASS FITTINGS
More information.09 3.1.0 1.1 1.44 1.71 1.73 1 5 1-70-3.70 1 HOSE ADAPTORS 0.58 0.1 0.70 0.73 0.83 0.85 0.95 0.93 1.03 1.41 1.1 1.71 1.98.0..3.0 3.08 1.3 1.54 0.89 0.91 1.07 1.4 1.7 1.9 1.17.31.30 0.9 0.37 0.7 0.89 1.18
More informationPVC. Pollet Pool Group 23 HYDROTUBO HYDROTUBO ASTORE FITTINGS GRIFFON GLUE AND ACCESSORIES PVC
23 HYDROTUBO... 282 HYDROTUBO +... 283 ASTORE FITTINGS... 284 GRIFFON GLUE AND ACCESSORIES... 289 Pollet Pool Group 23 281 HYDROTUBO Flexible thermoplastic tube reinforced with polymers for suction and
More information485 - NC NO/DA DN
485 - NC 285 - NO/DA DN 25-100 The 485/285 diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. The new internal geometry of the body optimises fluid dynamic
More informationFRIATHERM multi / FRIATHERM uni Push-fit system / Press-fit system for drinking water and heating networks
fittings networks Fittings and accessories 9 Transitions, external thread, short 9 Union couplings, external thread 9 Flanges 9 FRIATHERM Component+ adhesive 10 Transition sleeves 11 s - 20 cm 11 FRIATHERM
More informationPIPING. Aluminium pipe for inert gases (5,7 m / 18,7 ft) PAGE 2/ AIRNET Ø (MM / INCH) PARTNUMBER LOT SIZE / ¾" 05
PIPING Aluminium pipe for inert gases (5,7 m / 18,7 ft) 2811 1061 05 20 / ¾" 05 2811 2061 05 25 / 1" 05 PAGE 2/99 2014-11-24 Aluminium pipe for air (2,85 m / 9,4 ft) PIPING 2811 1063 10 20 / ¾" 10 2811
More informationBall & Socket Fittings (Bauer Style)
Page 96 Ball & Socket Fittings (Bauer Style) Elbow-Bauer Style 3-1/ * *1 MM 76 89 108 133 159 194 2 300 * Locking Bar (part # 9-7318) for & 1 Lever is Sold Separately 6-9038 6-9039 6-9040 6-9041 6-9042
More informationFlowmeter DFM
Flowmeter DFM 165 50 Nominal size DN 10-65 Nominal size /8 2 1/2 Nominal pressure PN 10 bar Features Measuring range to 50,000 l/h suitable for a wide range of applications for gaseous medium types, water,
More informationCast Iron Valves. Product Information. It s all at Albion
Cast Iron Valves Product Information It s all at Albion ART 77-78 Cast Iron Ball Valve Flanged Ends Flange Mounting PN16 Only ISO 5211 Direct Mount (Not 200mm) Art 77/78 Plated Brass/Stainless Ball BS
More informationPNEUMATICALLY ACTUATED 2-WAY
482 DN 25-65 The 482 diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. The new internal geometry of the body optimises fluid dynamic efficiency by increasing
More informationFlow switches for insertion installation
Flow switches for insertion installation Threaded adapter with trimmable paddle Type VHS06 Type VK306 Technical data VHS06 VK306 Switching function Contact closes at increasing flow opens at decreasing
More informationAir Handling Piping Systems
Air Handling Piping Systems ProVent - Compressed Air System - PP Vent Duct System www.asahi-america.com Table of Contents Table of Contents Product Specification... Page 350 SOCKET PIPE AND FITTINGS Pipe,
More informationControl Components Pty Ltd. Drawing Number. Indicator Model Overview A 66.01A Side flanged connection
ABN 24 8 175 293 PO Box 212 Caringbah NSW 1495 Sydney Australia ph: +61 ()2 9542 8977 fx: +61 ()2 9542 7978 www.controlcomponents.com.au HELP@controlcomponents.com.au Magnetic Visual Level Indicators made
More informationValves for building. Y-strainers... page 204 PVC valves Ball valves... page 204 Butterfly valve... page 204 Ball check valve...
Valves for building Ball valves PN25/20... page 194 PN30/20... page 195 PN40/30 - Lead-free brass... page 196 Valve for gas... page 197 Stem extension valves... page 197 3 way valves... page 197 Mini valves...
More informationJUST PIPING, JUST FITTING. A Comprehensive Integrated Solution For Piping Systems
JUST PIPING, JUST FITTING A Comprehensive Integrated Solution For Piping Systems SF 01 DUCTILE IRON PIPE FITTINGS FD1011 FD1021 FD1022 FD1031 FD1102 FD1103 FD1111 FD1121 Double Flanged Piece Flanged spigot
More informationK-Factor. Global Installation Fittings and K-Factors. Global
K-Factor Global Installation Fittings an K-Factors Global K-Factor CD Table of Contents 5 6 7 8 13 14 21 22 27 28 35 36 37 38 39 40 47 48 49 50 51 52 59 60 61 62 63 64 65 66 67 68 79 80 81 82 83 84 91
More informationFor compressed air distribution solvent cementing with fast curing
No corrosion Clean air Solvent cementing with fast curing welding polymer Bs2d0 Fire classification: Bs2d0 For compressed air distribution solvent cementing with fast curing welding polymer Compressed
More informationValves for building. Y-strainers... page 272 PVC valves Ball valves... page 272 Butterfly valves... page 272 Ball check valves...
Valves for building Ball valves PN25/20... page 262 PN30/20...pages 262 to 263 PN40/30 - Lead-free brass... page 264 Valve for gas... page 265 Stem extension valves... page 265 3 way valves... page 265
More informationDiaphragm valve, Plastic
Diaphragm valve, Plastic Construction The GEMÜ manually operated 2/2-way diaphragm valve has a low maintenance plastic bonnet. An optical position indicator is integrated as standard. Features Suitable
More informationPraher S4 Ball Valve. manual valves. Praher Type S4 Ball Valve. Materials. Size. Pressure Rating. Features. Connections.
Praher S4 Ball Valve Praher Type S4 Ball Valve Descripti: In-line double uni ball valve with lockable handle Mounting: In any positi Maximum Fluid Pressure at 20 C: s 16mm to 7mm - 10bar; s 90mm to 110mm
More informationGeorg Fischer Waga N.V. A BIG welcome MULTI/JOINT 3000 Plus DN450 - DN600
Georg Fischer Waga N.V. A BIG welcome MULTI/JOINT 3000 Plus 40 - The original just got BIGGER and BETTER! The well-known and trusted wide range MULTI/JOINT 3000 Plus system has now been extended with the
More informationVR DN PVC-U. Check valve
VR DN 10 100 PVC-U Check valve VR DN 10 100 The VR is an angle seat check valve with weighted PVC piston that allows the passage of fluid in one direction only CHECK VALVE Connection system for solvent
More informationMULTI/JOINT 3000 Plus. The connection for all pipe diameters Restraint Non restraint DN50 DN400. Georg Fischer Waga N.V.
MULTI/JOINT 3000 Plus The connection for all pipe diameters Restraint Non restraint DN50 DN400 Georg Fischer Waga N.V. DAS ORIGINAL EL ORIGINAL HET ORIGINEEL THE ORIGINAL MULTI/JOINT 3000 Plus >> Wide
More informationDiaphragm Valve, Plastic
Diaphragm Valve, Plastic Construction The GEMÜ motorized plastic diaphragm valve has a low maintenance electric actuator and a reversible synchronous motor. It is operated via a non-self-locking reduction
More informationMULTI/JOINT. One size fits and grips all End-load resistant - Flexible DN50 - DN600
MULTI/JOINT One size fits and grips all End-load resistant - Flexible DN50 - DN600 1 MULTI/JOINT FITTINGS large tolerance fittings It means that pipes that can be fitted may have different diameters, with
More informationNSF/ANSI 61 Drinking Water System Components Health Effects
The Public Health and Safety Organization NSF Product and Service Listings These NSF Official Listings are current as of Thursday, January 08, 2015 at 12:15 a.m. Eastern Time. Please contact NSF International
More informationPlast/Joint. The mechanical connection with unique one bolt system for plastic pipes d63 d315
Plast/Joint The mechanical connection with unique one bolt system for plastic pipes d63 d315 Plast/Joint >> Quick and efficient installation due to one bolt system >> Do you encounter repairs at difficult
More informationDiaphragm Valve, Plastic
Diaphragm Valve, Plastic Construction The GEMÜ motorized plastic diaphragm valve has a low maintenance electric actuator and a reversible synchronous motor. It is operated via a non-self-locking reduction
More informationDiaphragm Valve, Plastic 2/2 way, motorized
Diaphragm Valve, Plastic / way, motorized Construction Maintenancefree electric actuator Maintenancefree toothed belt drive Reversible synchronous motor Manual override Optical position indicator Features
More informationCATALOG. Actuated Diaphragm Valve DN PVC-U / PVC-C / PP-H / PVDF / ABS SMART IN FLOW CONTROL.
CATALOG Actuated Diaphragm Valve DN 15-100 PVC-U / PVC-C / PP-H / PVDF / ABS SMART IN FLOW CONTROL. TABLE OF CONTENTS Type 186 - DN 12-15 (MA 10) 04 General information - Technical specification 04 Sectional
More informationi butt weld spigot i flanged end acc. to DIN PN 10 / 16
body material PVC-U PVC-C PP PVDF ball seat PTFE other seats iepdm ifpm i *) working temperature 0 C to 50 C 0 C to 90 C -20 C to 80 C nominal size DN to DN connection with pipe legth acc. to EN 558-1
More informationInstrumentation Products F Series Manifolds and Multi-Way Cocks
Instrumentation Products F Series Manifolds and Multi-Way Cocks Introduction Introduction The AS-Schneider Group with its headquarters in Germany is one of the World s Leading Manufacturers of Instrumentation
More information611, 671. Diaphragm Valve, Metal
Diaphragm Valve, Metal Construction The 611 and 671 manually operated 2/2-way metal diaphragm valves have a low maintenance plastic bonnet and an integral optical position indicator as standard. Features
More informationIndustrial Couplings and Fittings
Kamlok Quick Couplings: An asymmetrical coupling system, male and female parts are locked y two andles. Hose assemly for MIL-Norm couplings wit standard clamps, for DIN EN 14 420-7 couplings wit forged
More informationPVC WELL CASING & FITTINGS 20 FT. BELL-END /8 SDR21 REDUCING COUPLINGS STEEL WELL CASING & FITTINGS
Pipe Pipe & Well Casing FT. BELL-END 0 7 293 2 2 29 27 23 " SCH0 -/2" SDR7 " SDR2 " SCH0 " SCH0 FT. BELL-END 37 32 30 29 2 " SCH0 -/2" SDR7 -/" DR27. PVC WELL CASING & FITTINGS FT. BELL-END 003 7 -/ SDR2
More informationIndustrial Couplings and Fittings
Kamlok Quick Couplings: An asymmetrical coupling system, male and female parts are locked y two andles. Hose assemly for MIL-Norm couplings wit standard clamps, for DIN EN 14 420-7 couplings wit forged
More informationupvc PRESSURE AND COMPRESSION FITTINGS
upvc PRESSURE AND COMPRESSION FITTINGS Company Profile Proplastics is the leading supplier of world class plastic pipe systems for water and sewer reticulation in Southern Africa. Established in 1965,
More informationVisual Level Indicators (VLI) Plastic & Top of Tank Series Series Type Material Pipe Operating Operating Page
Visual Level Indicators (VLI) Plastic & Top of Tank Series Series Type Pipe Operating Operating Page O.D. x s Pressure Temperature Plastic thread 10 25670 PVDF 63.0 x 3.6 2.5-10 thread max. 140 C 61 Plastic
More informationACCESSORIES & FITTINGS 800 SERIES CONTROL VALVES
ACCESSORIES & FITTINGS 800 SERIES CONTROL VALVES 8 VALVE FITTING PART NUMBERS 2" & 3" PRESSURE REDUCING VALVES* 10645 8970-002 (9526-006) 1/4" tube (9526-006) Flow 8970-001 (9526-001) 8970-010 (9526-010)
More informationFittings threads: metric (M5), BSP (G1/8, G1/4, G3/8, G1/2, G3/4, G1), BSPT (R1/8, R1/4, R3/8, R1/2, R3/4, R1)
> Series 2000 pipe fittings Series 2000 pipe fittings Fittings threads: metric (M5), BSP (G1/8, G1/, G3/8, G1/2, G3/, G1), BSPT (R1/8, R1/, R3/8, R1/2, R3/, R1) The wide range of Camozzi pipe fittings,
More informationIndex. 01 PVC ball valves. 02 PP ball valves. 03 upvc Superior ball valves. 04 Butterfly valves. 05 Replacement parts.
00 00 Index 01 PVC ball valves Specifications and characteristics Two-way ball valves Three-way ball valves 3 piece unions 02 PP ball valves Specifications and characteristics Water-meter valve Ball valves
More informationGEMÜ 205 Electrically operated solenoid valve
Electrically operated solenoid valve Features Hermetic separation between medium and actuator In case of power failure operation possible by manual override Standard integral optical position indicator
More informationSolenoid Valve, Plastic
Solenoid Valve, Plastic Construction The EMÜ directly controlled 2/2-way plastic solenoid valve has a high performance coil which is hermetically separated from the medium by means of a flexible PTFE bush.
More informationode V C C C LERA FIP Formatura Iniezione Polimeri
FITTINGS PVC-U The range of PVC-U products includes a complete series of solvent weld, threaded and adaptor fittings for pipes conveying fluids under pressure at maximum working temperatures not exceeding
More informationIGATEC - Standard - Swivel Joints
IGATEC - Standard - Swivel Joints Type LW Swivel Joints with Welding Connection Swivel Joints with Threaded Connection Swivel Joints for Loading Arms Swivel Joints for Food and Pharmaceuticals IGATEC International
More informationDiaphragm Valve, Plastic
Diaphragm Valve, Plastic Construction The GEMÜ pneumatically operated 2/2-way valve has a low maintenance piston actuator which can be controlled by inert gaseous media. It has an integral optical position
More informationCamlocks. Snaplock Camlock Couplings. The original Snaplock quick release coupling. Applications
Snaplock Camlock Couplings The original Snaplock quick release coupling The tried & trusted cam coupling with the high reputation of the Snaplock brand name offering additional features to our standard
More informationFactory address: Mola sadra st., Abooreyhan st Eshtehard Industrial Town, TEHRAN/ IRAN
z d Le mm equiv inch Le r 1) z z Le L 110 5 2 5 5 8 2 Elbow d 1 51/2 210 2 1 6 2 0 7 2 272 8 0 0 5 9 8 291 2 10 375 0 0 11 3 73 78 355 1 5 93 0 511 675 531 0 7 1 0 8 625 6 25 95 653 710 1065 686 1 7 900
More informationUSING EXABOND TECHNOLOGY LINER PIPE
LINER PIPE Inside Diameter Liner Thickness DN - Nominal diameter S 1 - Liner wall thickness d 2 - Outside diameter of liner Liner material density for PVC: 1.38g/cm 3 Liner material density for PVC-C:
More informationHANDBOOK PIPING ACCESSORIES. Ed PIPING ACCESSORIES AT-ED 01/ ENG 1
HANDBOOK Ed. 2017 AT-ED 01/2017 - ENG 1 CHAPTER 3 ACCESS FITTINGS AND VALVE CORES FOR REFRIGERATION PLANTS THAT USE HCFC, HFC, HC, HFO, OR R744 REFRIGERANTS APPLICATIONS The access fittings illustrated
More informationHDPE PIPE SYSTEMS PRODUCT CATALOGUE.
HDPE PIPE SYSTEMS PRODUCT CATALOGUE www.acu-tech.com.au This is to certify that: The Trustee for The Morren Family Trust ABN 52 394 633 042 Trading As Acu-Tech Piping Systems 119 Kelvin Road Maddington
More informationVALVES. valves. valves
VALVES Plasson have been in service in excess of 45 years in many demanding applications. Proven Reliability: Safe control of water supplies for many years worldwide. Robust Construction: The use of high
More informationFE DN PVC-U. Butterfly valve
FE DN 40 200 PVC-U Butterfly valve FE DN 40 200 The FE is a butterfly valve for shutting off or regulating flow, specifically designed for water applications and equipped with a customisable Labelling
More informationDiaphragm Valve, Plastic
Diaphragm Valve, Plastic Construction The GEMÜ motorized plastic diaphragm valve has a low maintenance electric actuator and a reversible synchronous motor. It is operated via a non-self-locking reduction
More information:,Rhino SD/XD G/D 24 Vdc ISO
:,Rhino SD/XDG/D Vdc ISO ()Rhino SD/XD() SD/XD Rhino SD/XDG/D Vdc ISO Rhino SD/XD, Rhino SD/Xd, (Rhino SD/XD) 006 Nordson Corporation P/N 75606A-0 Rhino SD/XDG/D Vdc ISO 0 9 5 8 7 6 P/N 75606A-0 006 Nordson
More information611, 671. Diaphragm Valve, Metal
Distributed by: Tel: 905.677.9000 Toll Free: 1.0.486.7863 www.tricanada.com Diaphragm Valve, Metal Construction The 611 and 671 manually operated 2/2-way metal diaphragm valves have a low maintenance plastic
More informationR690. Diaphragm Valve, Plastic
Diaphragm Valve, Plastic Construction The GEMÜ diaphragm valve has a low maintenance membrane actuator which can be controlled by air or inert gases. Normally Closed (NC), Normally Open (NO) and Double
More informationLATEST ARRIVALS CATALOGUE STOCK
LATEST ARRIVALS CATALOGUE STOCK PIPES VALVES FLANGES & FITTINGS IN CARBON STEEL STAINLESS STEEL LATEST ARRIVALS!!!!!! VALVE PRODUCTS CAST IRON WAFER TYPE BUTTERFLY VALVE, PINLESS SHAFT, DUCTILE NICKEL
More informationSUPERSEDES ABS-C0811/AUG.
ABS-C0612/R JUNE 2012 SUPERSEDES ABS-C0811/AUG. 2011 SANITARY TEE REDUCING TEE TEE - Left Side Inlet 600007 1 1/4" 0 62852 60000 5 50 4,800 15.41 600015 1 1/2" 0 62852 60001 2 90 2,880 8.27 600023 2"
More informationPush-Fit Transition Coupling for PE-100/PVC-U water pipes up to 16 bar patented
Push-Fit Transition Coupling for PE-100/PVC-U water pipes up to 16 bar patented PE-100 / PVC-U pull-out resistant long type Push-Fit Transition Coupling for PE-100 and PVC-U water pipes up to 16 bar d90
More information