LPRA/182000/M Double acting profile cylinders Ø mm
|
|
|
- Mae Howard
- 6 years ago
- Views:
Transcription
1 Double acting profile cylinders mm High performance, stability and reliability M/50 switches (solid state) can be mounted flush with the profile Cylinders and mountings conform to ISO (ISO 6431, VDMA and NFE ) Comprehensive range of mountings Wide temperature range Shock and vibration tested to EN 61373, Category 1, class A and B Technical features Medium: Compressed air, filtered, lubricated or non-lubricated Standard: ISO Operation: Double acting, magnetic piston, adjustable cushioning Operating pressure: bar ( psi) Operating temperature: C max. ( F max.) Air supply must be dry enough to avoid ice formation at temperatures below +2 C (+35 F). Air ports: ISO G parallel or NPT Cylinder diameters: 32, 40, 50, 63, 80, 100, 125 mm Strokes: Standard: see page below Non-standard strokes: Available ( mm) Materials: Profile barrel: anodised aluminium, End covers: pressure diecast aluminium Piston rod: stainless steel (martensitic) Piston rod seals: polyurethane Piston seals: polyurethane O-rings: nitrile rubber Technical data Cylinder (mm) Air ports 1/8 1/4 1/4 3/8 3/8 1/2 1/2 Piston rod (mm) Piston rod thread M10 x 1,25 M12 x 1,25 M16 x 1,5 M16 x 1,5 M20 x 1,5 M20 x 1,5 M27 x 2 Cushion length mm (inch) 19 (.75) 22 (.87) 24 (.94) 24 (.94) 27 (1.06) 34 (1.34) 41 (1.61) Theoretical thrusts at 6 bar (87 psi) outstroke N (lb) 482 (108) 754 (169) 1178 (265) 1870 (420) 3016 (678) 4710 (1059) 7363 (1656) Theoretical thrusts at 6 bar (87 psi) instroke N (lb) 414 (93) 633 (142) 990 (222) 1680 (378) 2722 (612) 4416 (993) 6882 (1547) Air consumption at 6 bar (87 psi) outstroke l/cm (inch 3 /inch) 0,056 (8.7) 0,088 (13.7) 0,137 (21.3) 0,218 (33.9) 0,35 (54.4) 0,55 (85.5) 0,86 (133.7) Air consumption at 6 bar (87 psi) instroke l/cm (inch 3 /inch) 0,048 (7.5) 0,074 (11.5) 0,114 (17.7) 0,195 (30.3) 0,32 (49.8) 0,51 (79.3) 0,79 (122.9) Option selector LP /182 / / Piston rod material Stainless steel martensitic (standard) Hard chromium plated Stainless steel austenitic Thread form (air ports only) ISO G parallel NPT Cylinder (mm) 032, 040, 050, 063, 080, 100, 125 Substitute C S Substitute A C Substitute Strokes (mm) 3000 max. Variants (magnetic piston) Standard Piston rod bellow Without cushion Double ended piston rod Four-positon cylinder Extended piston rod LP**/182***/MU/****/*** Substitute M MG MW JM MT MU Extension (mm) Standard strokes Cylinder (mm) Strokes (mm) N/rw/en
2 Mountings and service kit Model A AK B, G C D D2 F FH Page 5 Page 5 Page 6 Page 6 Page 6 Page 6 Page 7 Page 7 32 QM/8032/35 QM/8025/38 QA/8032/22 QA/8032/21 QA/8032/23 QA/8032/42 QM/8025/25 QA/8032/34 40 QM/8032/35 QM/8040/38 QA/8040/22 QA/8040/21 QA/8040/23 QA/8040/42 QM/8040/25 QA/8040/34 50 QM/8050/35 QM/8050/38 QA/8050/22 QA/8050/21 QA/8050/23 QA/8050/42 QM/8050/25 QA/8050/34 63 QM/8050/35 QM/8050/38 QA/8063/22 QA/8063/21 QA/8063/23 QA/8063/42 QM/8050/25 QA/8063/34 80 QM/8080/35 QM/8080/38 QA/8080/22 QA/8080/21 QA/8080/23 QA/8080/42 QM/8080/25 QA/8080/ QM/8080/35 QM/8080/38 QA/8100/22 QA/8100/21 QA/8100/23 QA/8100/42 QM/8080/25 QA/8100/ QM/8125/35 QM/8125/38 QM/8125/22 QM/8125/21 QM/8125/23 QA/8125/42 QM/8125/25 QA/8125/34 Model S SS SW UF U US Service kit Page 7 Page 7 Page 8 Page 8 Page 8 Page 8 Page 9 32 QA/8032/27 QA/8032/41 M/P19931 M/P19493 QM/8025/32 QA/8032/33 M/P40310 LQA/8032/00 40 QA/8040/27 QA/8040/41 M/P19932 M/P19494 QM/8040/32 QA/8040/33 M/P40311 LQA/8040/00 50 QA/8050/27 QA/8040/41 M/P19933 M/P19495 QM/8050/32 QA/8050/33 M/P40312 LQA/8050/00 63 QA/8063/27 QA/8063/41 M/P19934 M/P19496 QM/8050/32 QA/8063/33 M/P40313 LQA/8063/00 80 QA/8080/27 QA/8063/41 M/P19935 M/P19497 QM/8080/32 QA/8080/33 M/P40314 LQA/8080/ QA/8100/27 QA/8100/41 M/P19936 M/P19498 QM/8080/32 QA/8100/33 M/P40315 LQA/8100/ QM/8125/27 QA/8100/41 M/P19937 M/P19499 QM/8125/32 QM/8125/33 M/P71355 LQA/8125/00 N/rw/en
3 Switches Voltage V d.c. Current max. Temperature LED Features Cable length Cable type Protection class ma C ( F) PNP 2, 5, 10 m PVC 3 x 0,25 IP65 M/50/EAP/*V ma C ( F) NPN 2, 5, 10 m PVC 3 x 0,25 IP65 M/50/EAN/*V * Please insert the cable length 2, 5 or 10 m. Model Basic dimensions A WH L 2 G L8 + * G A - B VD PL PL VA E AM L 12 EE 1 EE KW ø B e 11 AP ø BA e 11 MM h 9 KV B SW L 9 BG T T BH * stroke 1 cushion screw BH ø mm BG AM AP Be 11 BAe 11 BG BH q E EE G KV KW L2 L , /8 27,5 M10x1, , /4 32 M12x1, /4 31 M16x1, /8 33 M16x1, , /8 33 M20x1, /2 37 M20x1, /2 46 M27x , L9 L12 MMh 9 PL q T SW VA VD WH at 0 mm per 25 mm Model (standard) ,5 M ,51 kg 0,06 kg LP#/182032/M/* , M , ,80 kg 0,08 kg LP#/182040/M/* ,5 46,5 M , ,33 kg 0,12 kg LP#/182050/M/* ,5 M ,80 kg 0,13 kg LP#/182063/M/* M ,25 kg 0,20 kg LP#/182080/M/* M ,81 kg 0,23 kg LP#/182100/M/* M ,5 65 8,00 kg 0,33 kg LP#/182125/M/* * Please insert standard stroke length. # Please insert A for ISO G parallel or C for NPT threads. N/rw/en
4 Cylinder variants LP./182000/JM Double ended piston rod M + 2 x L 8 + * * M L8 Model (standard) LP#/182032/MJ/* LP#/182040/MJ/* LP#/182050/MJ/* LP#/182063/MJ/* LP#/182080/MJ/* LP#/182100/MJ/* LP#/182125/MJ/* * Please insert standard stroke length. # Please insert A for ISO G parallel or C for NPT threads. LP./182000/MT Four-position cylinder L 10 + * 1 + * 2 * * L L11 L L 8 L 10 L 11 Model (standard) LP#/182032/MT/*/** LP#/182040/MT/*/** LP#/182050/MT/*/** LP#/182063/MT/*/** LP#/182080/MT/*/** LP#/182100/MT/*/** LP#/182125/MT/*/** * Please insert standard stroke length. ** Please insert standard stroke length 1 and stroke length 2 # Please insert A for ISO G parallel or C for NPT threads. * stroke length 1 and stroke length 2 N/rw/en
5 LP./182000/MG Piston rod bellow B øa A Max. Piston rod Model (standard) stroke extension B per for for bellow first further bellow bellow LP#/182032/MG/* LP#/182040/MG/* LP#/182050/MG/* LP#/182063/MG/* LP#/182080/MG/* LP#/182100/MG/* LP#/182125/MG/* * Please insert standard stroke length. # Please insert A for ISO G parallel or C for NPT threads. Mountings Front or rear stud mounting A Conforms to ISO 15552, type MX1 Piston rod swivel AK BB DD TG TG 4 B 1 F L 2 L BB DD TG kg Model (A) 32/40 17 M6 32,5/38 0,02 QM/8032/35 50/63 23 M8 46,5/56,5 0,05 QM/8050/35 80/ M10 72/89 0,08 QM/8080/ M ,14 QM/8125/35 B1 F L L kg Model (AK) 32 M10x1, ,20 QM/8025/38 40 M12x1, ,20 QM/8040/38 50/63 M16x1, ,65 QM/8050/38 80/100 M20x1, ,72 QM/8080/ M27x2 13, ,70 QM/8125/38 N/rw/en
6 Front flange B, G Conforms to ISO 15552, type MF1 and MF2 Foot mounting C Conforms to ISO 15552, type MS1 MF UF TF FB E FB MF TF UF kg Model (B, G) ,25 QA/8032/ ,35 QA/8040/ ,70 QA/8050/ ,80 QA/8063/ ,35 QA/8080/ ,20 QA/8100/ ,70 QM/8125/22 AB AH AO AT AU E T kg Model (C) ,15 QA/8032/ ,18 QA/8040/ ,30 QA/8050/ ,39 QA/8063/ ,80 QA/8080/ ,95 QA/8100/ ,40 QM/8125/21 ear clevis D Conforms to ISO 15552, type MP2 ear clevis D2 Conforms to ISO 15552, type AB6 LH UB FL B2 CB H 14 L B1 H 14 FL 1 EK f 8 B3 2 EK h 9 E AT AH AU AO ø AB T E M CB H14 EK f8 FL L LH M UB kg Model (D) ,11 QA/8032/ ,16 QA/8040/ ,22 QA/8050/ ,34 QA/8063/ ,54 QA/8080/ ,90 QA/8100/ ,70 QM/8125/23 B1 H14 B2 B3 EK h9 FL 1 2 kg Model (D2) , ,20 QA/8032/ , ,23 QA/8040/ , ,5 22 0,36 QA/8050/ , ,55 QA/8063/ , ,90 QA/8080/ , ,45 QA/8100/ , ,70 QA/8125/42 N/rw/en
7 Piston rod clevis F Conforms to DIN ISO 8140 LE CE K CL CM ø CK h11 Front or rear detachable trunnion FH Conforms to VDMA part 2, type MT 5/6 L 1 CL UW 1 TD e 9 E D H11 TL TM h14 CE CKh11 CL CM E LE K kg Model (F) 32 M10x1, ,09 QM/8025/25 40 M12x1, ,13 QM/8040/25 50/63 M16x1, ,5 0,33 QM/8050/25 80/100 M20x1, ,67 QM/8080/ M27x ,35 QM/8125/25 Dh11 L1 TDe9 TL TMh14 UW1 kg Model (FH) ,20 QA/8032/ , ,38 QA/8040/ , ,60 QA/8050/ , ,10 QA/8063/ , ,90 QA/8080/ ,50 QA/8100/ ,50 QA/8125/34 ear eye Conforms to ISO 15552, type MP4 Trunnion support S Conforms to ISO 15552, type AT4 EW FL L ø D 3 CD H 9 T 1 H 1 H7 ø D 1 F x 45 H 2 M ø D 2 A B 1 B 2 C CDH9 EW FL L M kg Model () , ,09 QA/8032/ , ,11 QA/8040/ , ,17 QA/8050/ , ,24 QA/8063/ , ,37 QA/8080/ , ,59 QA/8100/ , ,20 QM/8125/27 A B1 B2 C D1H7 D2 D3 F x 45 H1 H2 T1 kg Model (S) ,5 12 6, ,8 0,10 QA/8032/41 40/ , ,14 QA/8040/41 63/ , ,18 QA/8063/41 100/ , ,34 QA/8100/41 N/rw/en
8 LPA/182000/M Universal piston rod eye UF Conforms to DIN ISO 8139 Wide hinge SW Conforms to ISO 15552, type AB7 CN H 7 CE EN -0,1 ø CK H 9 EM G 1 ø D CA E LE AX L 1 ø S H 2 G 2 K 1 G 3 K 2 Gewinde AX CE CNH7 EN- 0,1 E LE kg Model (UF) 32 M10x1, ,09 QM/8025/32 40 M12x1, ,13 QM/8040/32 50/63 M16x1, ,33 QM/8050/32 80/100 M20x1, ,67 QM/8080/ M27x ,35 QM/8125/32 CA CKH9 D H2 EM G1 G2 G3 K1 K2 L1 S kg Model (SW) , ,6 10 6,6 0,05 M/P , ,6 11 6,6 0,07 M/P , , ,14 M/P , , ,18 M/P , , ,28 M/P , , ,42 M/P , , ,70 M/P19499 Universal rear eye U Conforms to ISO 15552, type MP6 Narrow hinge SS EN FL ø CN G 7 EM G 1 CN H 7 ø D CA E L 1 ø S H 2 G 2 K 1 G 3 K 2 CNH7 EN E FL kg Model (U) ,5 13 0,15 QA/8032/ ,25 QA/8040/ ,40 QA/8050/ ,55 QA/8063/ ,90 QA/8080/ ,50 QA/8100/ ,70 QM/8125/33 CA CNG7 D H2 EM G1 G2 G3 K1 K2 L1 S kg Model (SS) ,6 10 6,6 0,15 M/P ,6 11 6,6 0,20 M/P , ,48 M/P , ,50 M/P , ,75 M/P , ,20 M/P , ,50 M/P19937 N/rw/en
9 Swivel hinge US Conforms to VDMA part 2 EN -0,1 ø CN H 7 EU E G 1 ø D L 1 CH H 2 ø S K 1 K 2 G 2 G 3 CH CNH7 D EN -0,1 E EU G1 G2 G3 H2 K1 K2 L1 S kg Model (US) , ,6 6,6 13 0,19 M/P ,6 6,6 13 0,24 M/P , ,46 M/P , ,59 M/P , ,03 M/P , ,40 M/P , ,10 M/P ,40 M/P ,10 M/P71357 Warning These products are intended for use in industrial compressed air and rail transport systems only. Do not use these products where pressures and temperatures can exceed those listed under Technical features. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult NOGEN. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products. N/rw/en
LPRA/182000/M, ISO cylinder Magnetic piston, double acting
> > Ø 32... 125 mm > > High performance, stability and reliability > > M/50 switches can be mounted flush with the profile > > Cylinders and mountings conform to ISO 15552 (ISO 6431, VDM 24562 and NFE
PRA/181000, PRA/181000/M PRA/183000, PRA/183000/M
PA/181000, PA/181000/M M/50 switches can be mounted flush with the profile Conforms to DIN ISO 6431 and VDMA 24562 part 1 Mountings conform to DIN ISO 6431, VDMA 24562 part 2 and NFE 49-003-1 Polyurethane
PRA/182000, PRA/182000/M
Profile cylinders conforms to ISO 15552 Non-magnetic and magnetic piston Double acting Ø 32 to 125 mm High performance, stability and reliability M/50 switches can be mounted flush with the profile Cylinders
RA/8000, RA/8000/M. Pneumatic cylinders ISO 6431, VDMA and NFE Non-magnetic and magnetic piston Double acting Ø 32 to 320 mm
Pneumatic cylinders ISO 6431, VDMA 456 and NFE 49-003-1 Non-magnetic and magnetic piston Double acting Ø 3 to 30 mm Comprehensive range for the utmost versatility Conforms to DIN ISO 6431, VDMA 456 and
Our policy is one of continued research and development. We therefore reserve the right to amend,
Airmotor (Oscillator) with integrated switches Double acting Ø 50... 100 mm Complete functional unit for oscillating movement Conforms to ISO 6431 and VDMA 24562 Integrated 5/2 valve Frequency and speed
PRA/181000, PRA/181000/M PRA/183000, PRA/183000/M
PA/181000, PA/181000/M PA/183000, PA/183000/M Profile barrel with concealed tie rods Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic Piston Single Acting 32 to 100 mm
RA/192000/M. Compact cylinder ISO Magnetic piston, double acting Ø 20 to 125 mm
Compact cylinder ISO 2287 Magnetic piston, double acting Ø 20 to 25 mm Conforms to ISO 2287 M/50 switches can be mounted flush with the profile Magnetic piston as standard Seals ensure low friction operation
RA/28000, RA/ Pneumatic Cylinders ISO 6431, VDMA and NFE Non-magnetic and Magnetic, Single Acting 32 to 100 mm
Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic, Single Acting 32 to 100 mm ugged tie rod construction Polyurethane seals ensure efficient low friction operation and
LRA/8000/M/EX, LRA/8000/EX, ISO cylinder Magnetic & Non-magnetic piston, double acting
> > Ø 32... 320 mm > > Comprehensive range for the utmost versatility > > Wide temperature range > > Supplied complete with piston rod locknut > > Conforms to ISO 15552 (ISO 6431, VDM 24562 and NFE 49-003-1)
LRM/55401/M, Roundline cylinder Magnetic piston, double acting
LRM/5540/M, Roundline cylinder > > 3... 00 mm > > Clean line design > > Low friction, long life seals > > Standard magnetic piston for full control system versatility > > Non-lube operation > > Shock and
Strokes (mm) N/en
IVC cleanline Cylinder double acting, magnetic piston 32... 100 mm Cylinders and mountings conform to ISO 15552 Complete functional unit with LED display Central electrical connector, polarity-safe Integrated
12/95 N Our policy is one of continued research and development. We therefore reserve the right
Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic, Double Acting 32 to 125 mm Cylinders to VDMA Standard 24562, ISO 6431 and NFE 49-003-1 New polyurethane seals ensure
PRA/822000/M, PRA/ Smoothline cylinder Magnetic or non-magnetic piston, double acting
P/822000/M, P/822000 Smoothline cylinder > 32... 00 mm > Cylinder and mounting conform to ISO 5552 > eed or solid state switches can be mounted flush with the profile barrel > lternative air ports as standard
PRA/842000/M, PRA/ Clean Line cylinder Magnetic or non-magnetic piston, double acting
> > 32... 00 mm > > Cylinder and mounting conform to ISO 5552 > > Smooth and spherical Corrosion resitant design conforms to N 672-2, accepted in the food industry > > Special PU seals provide high performance
Our policy is one of continued research and development. We therefore reserve the right 1/98 N
ISO Cylinders Magnetic Piston Single Acting Ø 10 to 25 mm Magnetic piston as standard Conforming to ISO 6432 Corrosion resistance Nose mounting nut and piston rod locknut as standard Technical Data Medium:
RM/900/M Heavy duty cylinders Ø 1 1/4... 4
Heavy duty cylinders Ø 1 1/4... 4 Heavy duty cylinder ideal for a wide range of rail applications Extensive range of mountings Rugged, reliable long established design Magnetic piston as standard Mounting
Our policy is one of continued research and development. We therefore reserve the right
Corrosion resistant design Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Magnetic Piston Double Acting Ø 32 to 100 mm Accepted in the Food Industry Conforms to ISO 6431, VDMA 24562 and NFE
KA/8000, KA/8000/M. Cylinder Variants. Model Codes. Standard Strokes. Warning 7/97 N/UK
Stainless Steel VDMA/ISO Cylinders Non-magnetic and magnetic Piston Double Acting Ø 32 to 200 mm High corrosion and acid resistant Conforming to Standards ISO 6431, VDMA 24562 and NFE 49-003-1 Ideal for
RM/57200/M, RT/57200/M
Roundline Cylinders Magnetic Piston Double Acting Ø 8 to 63 mm Three different basic versions provide flexibility and wide range of application Magnetic piston as standard provides a wide range of control
PRA/182000, PRA/182000/M
Profile barrel with concealed tie rods Pneumatic Profile Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic Piston Double Acting Ø 32 to 125 mm M/50 Switches can be mounted flush
PVA/182000, PVA/182000/M
Smooth Line cylinders with or without integrated switches Double acting Ø 3... 100 mm Smooth and spherical profile design with concealed tie rods Special polyurethane wiper seal Body sealing conforms to
Available: Cylinders till july 2000 Spares till july /98 N
Available: Cylinders till july 2000 RM/55400/M Roundline Cylinders Magnetic Piston Double Acting 32 to 100 mm bore Magnet piston as standard provides a wide range of control options Attractive clean- line
10/97 N Our policy is one of continued research and development. We therefore reserve the right
ISO Cylinders Magnetic Piston Double Acting Ø 10 to 25 mm Magnetic piston as standard Conforming to ISO 6432 Corrosion resistance Buffer and adjustable cushioned models Supplied complete with nose mounting
PRA/182000, PRA/182000/M
Profile barrel with concealed tie rods Pneumatic Profile Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic Piston Double Acting Ø 32 to 125 mm M/50 Switches can be mounted flush
PRA/882000/M/EX, IVAC Clean Line cylinder Magnetic piston, double acting
> ø 3... 100 mm > Complete functional unit with LED display > TEX-zones depending on pilot control: zones &, II 3GD, Valve control module (VCM) zones 1 & 1, II GD, Pilot control on separate specification
Guide blocks for ISO/VDMA cylinders
Actuators Guide blocks or ISO/VDMA cylinders QA/8/51/ QA/8/61/ QA/8/81/ (long coupling) QA/8/85/ (short coupling) Ø 32 to 1 mm QA/8/61/ QA/8/51/ Conorms to ISO 6431, VDMA 24562 and NFE 49 3 1 Ensures protection
Our policy is one of continued research and development. We therefore reserve the right 10/99 N
Stainless Steel ISO Cylinders Magnetic Piston Double Acting Ø 12 to 25 mm High corrosion and acid resistance Magnetic piston as standard Conforming to ISO 6432 Suitable for applications in the Food Industry
AIR CYLINDER Series A23, A24
A23 - Magnetic A24 - Non-magnetic Double Acting s (Square type) Ø32-125 mm As per ISO 15552 / VDMA 24562 standards. Features Adjustable cushioning at both ends with elastomer pads Wide varieties of mountings
M/1000, Heavy Duty Cylinders Double Acting
> > Ø 2 to 12 (50 to 305 mm) > > Extremely rugged heavy duty construction - ideal for use in the most arduous conditions. > > Large range of bore sizes - ideal for a wide variety of industrial applications.
ACT-72. DA/8000 Double acting Ø mm
ISO/VDMA Cylinders DA/8000 Double acting Ø 32... 320 mm Conforms to ISO 6431, VDMA 24562 and NFE 49-003-1 High performance, ruggedness and reliability Extensive range of mountings Technical data Medium:
1/96 N Our policy is one of continued research and development. We therefore reserve the right
Roundline Cylinders Magnetic Piston Double cting 8 to 63 mm Very compact and shorter than the basic length of a corresponding ISO/VDM and roundline cylinder. Magnetic piston as standard provides a wide
AIR CYLINDER Series A12, A13
A12 - Non magnetic A13 - Magnetic S Double Acting ( Ø32-100 ) mm As per ISO 6431 / CETOP RP43P, RP53P standards Features Adjustable cushioning at both ends Wide varieties of mountings Low friction Long
AIR CYLINDER Series A25, A26
A25 - Magnetic A26 - Non-magnetic S Double End Double Acting - Ø32-100 mm As per ISO 15552 / VDMA 24562 standards Features Adjustable cushioning at both ends with elastomer pads Wide varieties of mountings.
NFPA Double acting imperial cylinders
> > Ø 4... 8 > > Adjustable captive cushion needle > > Constructed of the finest materials > > Magnetic piston standard > > Wide temperature range > > Shock and vibration tested to N 61373, Category 1,
ACTUATORS equipment engineering advantage
www.norgren.com/rail RAILINE PNEUMATIC MOTION & FLUID CONTROL SOLUTIONS YOU CAN SEE OUR THINKING engineering advantage ACTUATORS valves pressure switches AND transducers air line equipment fittings tubing
RM/28000/M Roundline cylinders (ISO)
RM/28000/M Roundline cylinders (ISO) Single acting, ISO 6432 - Ø 10... 25 mm Magnetic piston as standard enerally conforms to ISO 6432 High strength, double crimped end cap design Corrosion resistant Nose
Aluminium profile. Double-acting, cushioned, magnetic ø mm
> Series 4 cylinders Series 4 cylinders - Aluminium profile Double-acting, cushioned, magnetic ø 60-200 mm»» In compliance with ISO 643/ VDMA 24562 standards»» Rolled stainless steel rod»» Adjustable pneumatic
Tie rod cylinders, Series 523
Electric Drives and Controls Hydralics Linear Motion and Assembly Technologies Pneumatics Service Tie rod cylinders, Series 523 Technical data Tie rod cylinders, Series 523 Grey series, 32 25 mm ( /4"-5")
Cylinders Series 61 - Aluminium profile
CATALOGUE > Release 8. Cylinders Series 6 - Aluminium profile MOVEMENT > Cylinders Series 6 Single, double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00, 25 (ISO 5552)» ISO 5552 (corresponding to
ACT-74. Short stroke cylinders DC/91000/M, DC/93000/M Single acting Ø mm. Actuators DC/9 / /
Actuators Short stroke cylinders DC/91000/M, DC/93000/M Single acting Ø 12... 63 mm One third the basic length of a corresponding ISO/VDMA model Low friction, long life seal design Fully non-corrodible
M/ Rotary cylinders Rack & pinion version Magnetic or non-magnetic piston Double acting Ø 32 to 125 mm
otary cylinders ack & pinion version Magnetic or non-magnetic piston Double acting Ø 32 to 25 mm Suitable torques from,2 to 5,0 Nm/bar otation angles 90, 80, 270, 360 Adjustable cushioning Male and female
Series ICS and ICL Pneumatic Cylinders. Corrosion resistant stainless steel and aluminum cylinders
Series ICS and ICL Pneumatic Cylinders Corrosion resistant stainless steel and aluminum cylinders Series ICS and ICL cylinders New generation of stainless steel and clean line cylinders. Series ICS from
Double acting, cushioned, magnetic Ø mm
CATALOGUE > Release 8.7 > Series 40 cylinders Series 40 cylinders Double acting, cushioned, magnetic 60-200 - 250-320 mm In compliance with ISO 5552 standards and with the previous DIN/ISO 643 - VDMA 24562
Aluminium profile. TANDEM: Double thrust and traction forces. LOW FRICTION: Friction force reduced by over 40%
CATALOGUE > Release 8.7 > Series 6 cylinders Series 6 cylinders - Aluminium profile Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40,
Bore ø 32, 40, 50, 63, 80, 100, 125 Ports 32 = 1/8, 40/50 = 1/4, 63/80 = 3/8, 100/125 = 1/2
6 S E R I E S Cylinders Series 6 Catalog 2006 Single, double acting, magnetic (DIN/ISO 643) Bore: ø 32, 40, 50, 63, 80, 00, 25 cushioned [ /4, 9/6, 2, 2 /2, 3 /8, 4, 5 inch approximations] The Series 6
2. COMPACT CYLINDERS series STRONG (RS, RQ)
2. COMPACT CYLINDERS series STRONG (RS, RQ) A new series of compact cylinders for long s and heavy-duty applications standard supplied with oversized guides and rods, the first one with adjustable pneumatic
Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40, 50, 63, 80, 100, 125mm
CATALOGUE > Release 8.8 > Series 60 cylinders Series 60 cylinders Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40, 50, 63, 80, 00, 25mm»»
Single and double-acting, magnetic, cushioned Standard, low friction and low temperature versions ø 32, 40, 50, 63, 80, 100, 125mm
CATALOGUE > Release 8.6 > Series 60 cylinders Series 60 cylinders New version Single and double-acting, magnetic, cushioned Standard, low friction and low temperature versions ø 32, 40, 50, 63, 80, 00,
Aluminium tube and profile
> Series 63 cylinders CATALOGUE > 206 Series 63 cylinders - Aluminium tube and profile New Single and double-acting, magnetic, cushioned Versions: standard, low friction, high and low temperatures ø 32,
AIR CYLINDER Series A75, A76
A76 - n-magnetic A75 - Magnetic AIR CYLINDER Round s - Ø32, 40, 50 and 63 mm Double Acting with Adjustable Cushioning Features Available in magnetic and n magnetic version Adjustable cushioning at both
Aluminium profile. Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100 mm
> Series 62 cylinders CATALOGUE > Release 8.6 Series 62 cylinders - Aluminium profile Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 5552 standards and with the
Magnetic cylinders Series 27 1/ Double-acting, magnetic ø 20, 25, 32, 40, 50, 63 mm
CATALOGUE > Release 8.5 > Cylinders Series 27 Magnetic cylinders Series 27 Double-acting, magnetic ø 20, 25, 32, 40, 50, 63 mm»» Reduced dimensions»» Different mounting options»» Perfect alignment, perfect
M/44000/M. LINTRA Rodless cylinders Magnetic piston Double acting Ø 25 to 40 mm
LINTRA Rodless cylinders Magnetic piston Double acting Ø 5 to 40 mm New compact, space-saving design Proven sealing system Integral switch mounting Adjustable cushioning Magentic piston as standard Technical
Pneumatic cylinders, piston-ø mm Double acting with magnetic piston DIN ISO 15552
Pneumatic cylinders, piston-ø 32 100 mm Double acting with magnetic piston DIN ISO 15552 Technical data for series SL 050 450 Order code SL-032-0250-050 Series Piston-Ø Stroke length (mm) Type of cylinder
Large Bore Extruded Cylinders, ISO 6431 Series 41
Large Bore Extruded Cylinders, ISO 6431 Series 41 Double-acting cushioned, magnetic ø160-200 (DIN/ISO 6431)»» DIN/ISO 6431 VDMA 24562»» Rolled stainless steel rod»» Adjustable cushioning Cylinders Series
PRA/801000, PRA/803000, RA/801000, RA/ ISOLine cylinder, single acting
PR/80000, PR/80000, R/80000, R/80000 > ø 2... 00 mm > High performance adaptive cushioning system CS > High performance, stability and reliability Technical features Medium: Compressed air, filtered, lubricated
Profile Design Air Cylinder
Profile Design Air Cylinder Series CP5 ø, ø, ø, ø, ø, ø Features Conforms to VDMA 24 562 (parts 1 and 2), ISO 6431 and CETOP standards. Combines lightweight profile barrel design with enclosed tie rods
Series 6PF Positioning Feedback cylinders 1/ Double-acting low friction, magnetic ø 50, 63, 80, 100, 125 mm
CATALOGUE > Release 8.8 > Series 6PF cylinders Series 6PF Positioning Feedback cylinders Double-acting low friction, magnetic ø 50, 63, 80, 00, 25 mm»» In compliance with ISO 5552 standards and with the
Tie rods cylinders to ISO standard Ø
Tie rods cylinders to ISO 5552 standard 25 DESCRIPTION Cylinders series "XL" comply with ISO 5552 standard, being in this way completely interchangeable with the former cylinders to ISO 643 /VDMA 24562
-H- Note. -N- Diameters. -T- Stroke lengths. -W- Note. Standard cylinders DNU/DNUL to ISO 6431 Key features at a glance Festo AG & Co.
Standard cylinders DNU/DNUL to ISO 6431 Key features at a glance ISO and standard cylinders DNU/DNUL -H- Note For new applications use type DNC ( -54). -N- Diameters 32... 125 mm -T- Stroke lengths 10...
SERIES PRA AND TRB ISO PNEUMATIC CYLINDERS
SERIES PRA AND TRB ISO 15552 PNEUMATIC CYLINDERS Series PRA and TRB Pneumatic ISO 15552 Cylinders The next generation of ISO cylinders from AVENTICS The Series PRA and TRB cylinder series represent consistent
Single- and double-acting, cushioned, magnetic ø 32, 40, 50, 63, 80, 100 and 125 mm
> Series 90 stainless steel cylinders CATALOGUE > Release 8.8 Series 90 stainless steel cylinders Single- and double-acting, cushioned, magnetic ø 32, 40, 50, 63, 80, 00 and 25 mm» In compliance with ISO
Standard cylinders DNG/DNGZS, ISO 15552
Features Brief description Double-acting For contactless position sensing With adjustable end-position cushioning at both ends Robust tie rod design Standards-based cylinders to ISO15552 (corresponds to
Twin Rod Non Rotate Cylinders RDV and AZ
Twin Rod Non Rotate Cylinders RDV and AZ A range of twin rod cylinders designed for use in non rotate applications specifially suited to the handling and packaging environments. Offering a range of double
P1D-B Pneumatic Cylinders
P1D-B Pneumatic Cylinders According to ISO 15552 P1D-B series. This series features a profile design and is the basic ISO cylinder for simple applications where no special options are required. This series
Series 32 compact magnetic cylinders 1/ Single and double-acting, non-rotating ø 20, 25, 32, 40, 50, 63, 80, 100 mm
Series 32 compact magnetic cylinders Single and double-acting, non-rotating ø 20, 25, 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 2287»» Compact design»» Wide range of models available in different
Series 63 ISO cylinders
Series 63 ISO 15552 cylinders New versions Single and double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100, 125 mm In compliance with the ISO 15552 standard Weight reduced by 25% Low noise More
VERSION 1 / Basic cylinder T Double push tandem R Through rod F Hollow through rod. VERSION 2 D Double acting S Single acting front spring
Compact cylinders to AFNOR NF E49-004- DESCRIPTION Cylinders series BU are available from Ø 20 to Ø 00 and, complying with AFNOR NF E49-004-, they re interchangeable also without using anchorages. Besides
XG*-***-****-***-****
Technical details Cylinders > piston rod cylinders > Series XL, ISO ISO 15552, 15552, double double acting acting Operating pressure Temperature range Max. stroke Medium Materials 1... 10 bar -20 C...
Aluminium profile. Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100 mm
> Cylinders Series 62 CATALOGUE > Release 8.5 Cylinders Series 62 Aluminium profile Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 5552 standards and with the previous
Extruded Body Cylinders, ISO 6431, ISO compliant Series 61
1 ISO / VDMA Cylinders NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 Extruded Body Cylinders, ISO 6431, ISO 15552 compliant Series 61 Single or double-acting, magnetic, cushioned Standard and
Associated ranges. Body material. Stainless steel Aluminium
Associated ranges Series Body material Stainless steel Aluminium KA/8000,.../M Stainless steel tie-rod cylinders (ISO/VDMA) Double acting Ø 32 to 200 mm 216 KM/8000/M Stainless steel roundline cylinders
Series 31 compact cylinders 1/
Series 3 compact cylinders Double and single-acting, double-acting non-rotating, magnetic ø2, 6, 20, 25 mm ø 32, 40, 50, 63, 80, 00 mm UNITOP The compact dimensions allow Series 3 single and double-acting
STANDARDISED MOUNTINGS
STNDRDISED MOUNTINGS for PES / PLS cylinders conforming to ISO 15552-FNOR-DIN standard Series 434 MOUNTINGS CONFORMING TO ISO 15552 - FNOR NF ISO 15552 - DIN ISO 15552 STNDRDS B C pplications duty Construction
PRA/182000, PRA/182000/M ISO/VDMA Profile cylinders
P/182000, P/182000/M IO/VDM Profile cylinders onforms to IO 15552, IO 6431, VDM 24562 and NFE 49-003-1 Profile barrel with concealed tie rods High performance, stability and reliability Polyurethane seals
Tie-rod Cylinders, ISO 6431, ISO compliant Series 60
Tie-rod Cylinders, ISO 6431, ISO 15552 compliant Series 60 Single or double-acting, magnetic, cushioned Standard and low friction versions ø 32, 40, 50, 63, 80, 100, 125 mm In compliance with ISO 15552
M/46800/M, M/46800/HM, M/46800/PM
External guides for heavy loads over long distances Rigid, reinforced aluminium profile provides greater load support T-slots in the outer profile enable individual mounting options Precision guidance
Standard cylinders DNCB, ISO 15552
Standard cylinders DNCB, ISO 15552 Features At a glance Standards-based cylinders to ISO 15552 (corresponds to the withdrawn standards ISO 6431, DIN ISO 6431, VDMA 24 562, NF E 49 003.1 and UNI 10290)
PNEUMATIC CYLINDERS CYLINDERS ISO solutions SERIES 21 SERIES 21 CYLINDERS ISO 15552
PNEUMATIC CYLINDERS 1 2 3 4 SERIEs 21- General Information 32-100 mm diameter 21 series cylinders are manufactured to ISO 15552 standard which specifies interchangeable mounting dimensions. The cylinder
1.134 L INEAR A CTUATOR: AIR C YLINDER S ERIES C95
1.134 L INEAR A CTUATOR: AIR C YLINDER H O W M ADE I N USA T ECHNICAL T O O R D E R C95 AIR C YLINDERS C95 P ISTON R OD S Basic K Non-Rotating P ISTON - Basic D Magnetic B ORE IN MM 50 63 80 100 B S T
CYLINDERS. Moving more than air
CYLINDRS 1 Moving more than air Content 1-2 1-2 page 1.1 Round cylinders 1.1.1 RI(M) / RI(M) / RIB(M) / RID(M) Round cylinders according to ISO 6432 piston-ø 8 25 mm 3 1.1.2 Accessories for round cylinders
Tie rods cylinders to ISO standard
Tie rods cylinders to ISO 5552 standard seriescpui DESCRIPTION Cylinders series CPUI comply with ISO 5552 standard, being in this way completely interchangeable with the well-known cylinders to ISO 643
Sizes 32, 40, 50 and 63
> Series 6E electromechanical cylinders C_Electrics > 207 Series 6E electromechanical cylinders Sizes 32, 40, 50 and 63 The Series 6E cylinders are mechanical linear actuators with rod, in which the rotary
A44000, LINTRA-LITE Rodless Cylinders Non-magnetic and Magnetic Piston, double acting
> > Ø 25... 40 mm > > New compact, spacesaving design > > Proven sealing system > > Integral switch mounting > > uffer or adjustable cushioning > > Standard foot mountings Technical features Medium: Compressed
Single-acting and double-acting, magnetic Series 94: ø 16, 20, 25 mm Series 95: ø 25 mm, cushioned
> Series 94 and 95 stainless steel cylinders CATALOGUE > Release 8.7 Series 94 and 95 stainless steel mini-cylinders Single-acting and double-acting, magnetic Series 94: ø 6, 20, 25 mm Series 95: ø 25
Compact cylinders series NYD Double acting with magnetic piston, ISO M5 to G1/8 Piston Ø 20 to 100 mm
Compact cylinders series NYD Double acting with magnetic piston, ISO 21287 M5 to G1/8 Piston Ø 20 to 100 mm 200, 210 220 600, 610 620 Order code NYD-032-125-210 High force cylinder series NYDK and multiple
Single and double-acting, cushioned, magnetic. ø 32, 40, 50, 63 mm
> Series 97 stainless steel cylinders CATALOGUE > Release 8.7 Series 97 stainless steel cylinders Single and double-acting, cushioned, magnetic. ø 32, 40, 50, 63 mm»» Clean design»» Stainless steel AISI
V160C. Mould Hydraulic Systems. Hydraulic cylinders-iso 6020/2 compact 160 bar V160C
V160C Mould Hydraulic Systems Hydraulic cylinders-iso 6020/2 compact 160 bar V160C V160Ccat.GB01-2006 Hydraulic cylinders-iso 1 2 Chrome-plated steel rod, hardened or tempered and polished. Thickness of
ISO Cylinders - P1D-B
Flange MF1/MF2 Intended for fixed mounting of cylinder. Flange can be fitted to front or rear end cover of cylinder. Materials Flange: Surface-treated steel Mounting screws acc. to DIN 6912: Zinc-plated
HEAVY DUTY PNEUMATIC CYLINDERS
HEAVY DUTY PNEUMATIC CYLINDES Features: Conforms to ISO:30 standard. Double Acting, with adj. cushioning at both ends. Sizes: Ø, Ø, Ø, Ø, Ø, Ø0, Ø1, Ø0, Ø0 & Ø0. : Other bore sizes on request Seamless
Strokes Strokes Double acting. Min. stroke with 2 sensors Ø Single acting. Single acting
S version Type... Standards... Cushioning... Rated temperature... Fluid... Working pressure... Proximity switch... Mounting and accessories... Materials... Single and double acting pneumatic microcylinders,
TELESCOPIC CYLINDERS ø mm Series RT
TELESCOPIC CYLINDERS 25 63 mm Series RT The overall dimensions are one of the most imporant aspects: in comparison with a traditional ISO cylinder of the same a reduction in size of approx. 45% (with a
bar -20 C C ( C for high temperature version) 1000 mm
Technical details Cylinders > piston rod cylinders > ISO 15552, double acting Operating pressure Temperature range Max. stroke Medium Materials 1... 10 bar -20 C... +80 C ( 0... +150 C for high temperature
Hinge cylinders DW Key features
Key features At a glance Hinge cylinder for clamping components during the welding process Easy assembly thanks to swivel bearing on the bearing cap Integrated flow control Integrated end-position cushioning
Multi-position cylinders/adapter kits
Multi-position cylinders/adapter kits Multi-position cylinders ADNM Product range overview Function Version Type Piston Max. stroke Piston rod With female thread With male thread Doubleacting ADNM Single-ended
Short-stroke cylinders ADVC/AEVC
Short-stroke cylinders ADVC/AEVC q/w Worldwide: Superb: Easy: Festo core product range Covers 80% of your automation tasks Always in stock Festo quality at an attractive price Reduces procurement and storing
Double and single-acting, double-acting non-rotating, magnetic ø12, 16, 20, 25 mm ø 32, 40, 50, 63, 80, 100 mm UNITOP
CATALOGUE > Release 8.7 > Series 3 cylinders Series 3 compact cylinders Double and single-acting, double-acting non-rotating, magnetic ø2, 6, 20, 25 mm ø 32, 40, 50, 63, 80, 00 mm UNITOP» Compact design»
Cylinders DSBG to ISO 15552
Key features At a glance DIN Cylinders to ISO 15552 (corresponds to the withdrawn standards ISO 6431, DIN ISO 6431, VDMA 24562, NFE49003.1 and UNI 10290) Sturdy tie rod design Double-acting For contactless
ISOCLAIR ROUND CYLINDERS Ø 32 to 63 mm - single acting ISO CETOP with elastic cushioning
ISOCLAIR ROUND CYLINDRS 32 to 63 mm - single acting ISO 643 - CTOP with elastic cushioning SR NS Series 438 Type CIS-NA/DM GNRAL Detection quipped for magnetic position detectors Fluid Air or neutral gas,
ISO 6432 Ø mm. Page 9. Ø mm. RM/91000/M, RM/93000/M Ø mm. Ø mm ISO, VDMA, NFE. ISO, VDMA, NFE Ø 32...
Actuators Product selector table...2 Single acting cylinders Miniature roundline cylinders ( 2,5 & 4 mm)...9 ISO Roundline ( 10 to 25 mm)...10 Roundline ( 8 to mm)...20 VDMA compact ( 20 to 63 mm)...32