Cree XLamp XP-G2 LEDs

Transcription

1 Cree XLamp XP-G2 LEDs Product family data sheet CLD-DS51 Rev 12H Product Description FEATURES Table of Contents The XLamp XP-G2 LED builds on the unprecedented performance of the original XP-G by increasing lumen output up to 20% while providing a single die LED point source for precise optical control. The XP-G2 LED shares the same footprint as the original XP-G, providing a seamless upgrade path and shortening the design cycle. XLamp XP-G2 LEDs are the ideal choice for lighting applications where high light output and maximum efficacy are required, such as LED light bulbs, outdoor lighting, portable lighting, indoor lighting and solar-powered lighting. Available in white, outdoor white and 80-, 85- and 90-CRI white ANSI-compatible chromaticity bins Binned at 85 C Maximum drive current: 1500 ma Low thermal resistance: 4 C/W Wide viewing angle: 115 Unlimited floor life at 30 ºC/85% RH Reflow solderable - JEDEC J STD 020C Electrically neutral thermal path RoHS and REACh compliant UL recognized component (E349212) Copyright Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and XLamp are registered trademarks and the Cree logo is a trademark of Characteristics...2 Flux Characteristics...3 Relative Spectral Power Distribution Relative Flux vs. Junction Temperature Electrical Characteristics Relative Flux vs. Current Relative Chromaticity vs Current and Temperature Typical Spatial Distribution Thermal Design Performance Groups Luminous Flux Performance Groups Chromaticity Cree s Standard Chromaticity Regions Plotted on the 1931 CIE Curve Cree s Standard Cool White Kits Plotted on ANSI Standard Chromaticity Regions Cree s Standard Warm and Neutral White Kits Plotted on ANSI Standard Chromaticity Regions Cree s Standard Chromaticity Kits Bin and Order Code Formats Reflow Soldering Characteristics Notes Mechanical Dimensions Tape and Reel Packaging Cree, Inc Silicon Drive Durham, NC USA Tel:

2 Characteristics Characteristics Unit Minimum Typical Maximum Thermal resistance, junction to solder point C/W 4 Viewing angle (FWHM) degrees 115 Temperature coefficient of voltage mv/ C -1.8 ESD withstand voltage (HBM per Mil-Std-883D) V 8000 DC forward current ma 1500 Reverse voltage V 5 Forward voltage (@ 350 ma, 85 C) V Forward voltage (@ 700 ma, 85 C) V 2.9 Forward voltage (@ 1000 ma, 85 C) V 3.0 Forward voltage (@ 1500 ma, 85 C) V 3.1 LED junction temperature C 150 2

3 Flux Characteristics (T J = 85 C) The following table provides order codes for XLamp XP-G LEDs. For a complete description of the order code nomenclature, please see the Bin and Order Code Formats section (page 24). For definitions of the chromaticity kits, please see the Cree s Standard Chromaticity Kits section (page 23). Chromaticity Kit CCT Code Minimum C* Order Codes 70 CRI Typical S L51 S K K S J51 R H51 R G51 R F51 S L53 S K K S J53 R H53 R G53 R F53 S L50 S K K S J50 R H50 E K R G50 R F50 S LE1 S KE1 S JE1 R HE1 R GE1 R FE1 Notes Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a tolerance of ±2 on CRI measurements. See the Measurements section (page 26). Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code. * Flux 25 C are calculated and for reference only. 3

4 Flux Characteristics (T J = 85 C) - Continued Chromaticity Kit CCT Code Minimum C* Order Codes 70 CRI Typical E K S LE2 S KE2 S JE2 R HE2 R GE2 R FE2 Chromaticity Kit CCT Code Minimum C* Order Codes 70 CRI Typical 75 CRI Typical 80 CRI Minimum E3 F K 4750 K S LE3 S KE3 S JE3 00JE3 R HE3 00HE3 R GE3 00GE3 R FE3 00FE3 R EE3 00EE3 Q DE3 S LF4 S KF4 S JF4 00JF4 R HF4 00HF4 R GF4 00GF4 R FF4 00FF4 R EF4 00EF4 Q DF4 Notes Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a tolerance of ±2 on CRI measurements. See the Measurements section (page 26). Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code. * Flux 25 C are calculated and for reference only. 4

5 Flux Characteristics (T J = 85 C) - Continued Chromaticity Kit CCT Code Minimum C* Order Codes 70 CRI Typical 75 CRI Typical 80 CRI Minimum E4 F5 E5 Z K 4250 K 4000 K 4000 K S LE4 S KE4 S JE4 00JE4 R HE4 00HE4 R GE4 00GE4 R FE4 00FE4 R EE4 00EE4 Q DE4 S LF5 S KF5 S JF5 00JF5 R HF5 00HF5 R GF5 00GF5 R FF5 00FF5 R EF5 00EF5 Q DF5 S LE5 S KE5 S JE5 00JE5 R HE5 00HE5 00HE5 R GE5 00GE5 00GE5 R FE5 00FE5 00FE5 R EE5 00EE5 00EE5 Q DE5 00DE5 R HZ5 00HZ5 R GZ5 00GZ5 R FZ5 00FZ5 R EZ5 00EZ5 Q DZ5 00DZ5 Notes Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a tolerance of ±2 on CRI measurements. See the Measurements section (page 26). Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code. * Flux 25 C are calculated and for reference only. 5

6 Flux Characteristics (T J = 85 C) - Continued Chromaticity Kit CCT Code F6 E6 Z K 3500 K 3500 K Minimum C* S R R R R Q S R R R R Q R R R Q Order Codes 70 CRI Typical 80 CRI Typical 80 CRI Minimum 85 CRI Minimum 90 CRI Minimum 00JF6 00HF6 00GF6 00FF6 00EF6 00DF6 00JE6 00HE6 00GE6 00FE6 00EE6 00DE6 00HF6 00GF6 00FF6 00EF6 00DF6 00HE6 00GE6 00FE6 00EE6 00DE6 00GZ6 00FZ6 00EZ6 00DZ6 00HF6 00GF6 00FF6 00EF6 00DF6 00HE6 00GE6 00FE6 00EE6 00DE6 00GZ6 00FZ6 00EZ6 00DZ6 Notes Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a tolerance of ±2 on CRI measurements. See the Measurements section (page 26). Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code. * Flux 25 C are calculated and for reference only. 6

7 Flux Characteristics (T J = 85 C) - Continued Chromaticity Kit CCT Code F7 E K 3000 K Minimum C* S R R R R Q S R R R R Q Q Q Q P P Order Codes 70 CRI Typical 80 CRI Typical 80 CRI Minimum 85 CRI Minimum 90 CRI Minimum 00JF7 00HF7 00GF7 00FF7 00EF7 00JE7 00HE7 00GE7 00FE7 00EE7 00HF7 00GF7 00FF7 00EF7 00DF7 00HE7 00GE7 00FE7 00EE7 00DE7 00CE7 00HF7 00GF7 00FF7 00EF7 00DF7 00HE7 00GE7 00FE7 00EE7 00DE7 00CE7 00EE7 00DE7 00CE7 00BE7 00AE7 009E7 008E7 00EE7 00DE7 00CE7 00BE7 00AE7 009E7 008E7 Notes Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a tolerance of ±2 on CRI measurements. See the Measurements section (page 26). Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code. * Flux 25 C are calculated and for reference only. 7

8 Flux Characteristics (T J = 85 C) - Continued Chromaticity Kit CCT Code Z7 F K 2850 K Minimum C* R R R Q Q Q Q P P R R R Q Q Q Q P P P Order Codes 70 CRI Typical 80 CRI Typical 80 CRI Minimum 85 CRI Minimum 90 CRI Minimum 00GZ7 00FZ7 00EZ7 00DZ7 00CZ7 00GF8 00FF8 00EF8 00DF8 00CF8 00BF8 00GZ7 00FZ7 00EZ7 00DZ7 00CZ7 00GF8 00FF8 00EF8 00DF8 00CF8 00BF8 00DZ7 00CZ7 00BZ7 00AZ7 009Z7 008Z7 00DF8 00CF8 00BF8 00AF8 009F8 008F8 007F8 00DZ7 00CZ7 00BZ7 00AZ7 009Z7 008Z7 00DF8 00CF8 00BF8 00AF8 009F8 008F8 007F8 Notes Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a tolerance of ±2 on CRI measurements. See the Measurements section (page 26). Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code. * Flux 25 C are calculated and for reference only. 8

9 Flux Characteristics (T J = 85 C) - Continued Chromaticity Kit CCT Code E8 Z K 2700 K Minimum C* R R R Q Q Q Q P P P R R Q Q Q Q P P P Order Codes 70 CRI Typical 80 CRI Typical 80 CRI Minimum 85 CRI Minimum 90 CRI Minimum 00GE8 00FE8 00EE8 00DE8 00CE8 00BE8 00FZ8 00EZ8 00DZ8 00CZ8 00BZ8 00GE8 00FE8 00EE8 00DE8 00CE8 00BE8 00FZ8 00EZ8 00DZ8 00CZ8 00BZ8 00CE8 00BE8 00AE8 009E8 008E8 007E8 00BZ8 00AZ8 009Z8 008Z8 007Z8 00CE8 00BE8 00AE8 009E8 008E8 007E8 00BZ8 00AZ8 009Z8 008Z8 007Z8 Notes Cree maintains a tolerance of ±7% on flux and power measurements, ±0.005 on chromaticity (CCx, CCy) measurements and a tolerance of ±2 on CRI measurements. See the Measurements section (page 26). Cree XLamp XP-G2 LED order codes specify only a minimum flux bin and not a maximum. Cree may ship reels in flux bins higher than the minimum specified by the order code without advance notice. Shipments will always adhere to the chromaticity bin restrictions specified by the order code. * Flux 25 C are calculated and for reference only. 9

10 Relative Spectral Power Distribution 100% 80% Relative Radiant Power 60% 40% 20% 5000 K K CCT 3700 K K CCT 2600 K K CCT 0% Wavelength (nm) Relative Flux vs. Junction Temperature (I F = 350 ma) 120% 100% Relative Luminous Flux 80% 60% 40% 20% 0% Junction Temperature (ºC) 10

11 Electrical Characteristics (T J = 85 C) Forward Current (ma) Forward Voltage (V) Relative Flux vs. Current (T J = 85 C) 350% 300% Relative Luminous Flux 250% 200% 150% 100% 50% 0% Forward Current (ma) 11

12 Relative Chromaticity vs Current and Temperature (Warm White*) ΔCCx ΔCCy Current (ma) ΔCCx ΔCCy Tsp ( C) * Warm White XLamp XP-G2 LEDs have a typical CRI of

13 Typical Spatial Distribution 100% Relative Luminous Intensity 80% 60% 40% 20% 0% Angle (º) Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics Maximum Current (ma) Rj-a = 10 C/W Rj-a = 15 C/W Rj-a = 20 C/W Rj-a = 25 C/W Ambient Temperature (ºC) 13

14 Performance Groups Luminous Flux XLamp XP-G2 LEDs are tested for luminous flux and placed into one of the following luminous flux groups: Group Code Minimum Luminous Flux 350 ma Maximum Luminous Flux 350 ma P P P Q Q Q Q R R R R S S S S

15 Performance Groups Chromaticity Region x y Region x y Region x y Region x y A B 0C 0D R S 0T 0U A B 1C 1D R S 1T 1U A B 2C 2D R S 2T 2U A B 3C 3D R S A B 4C 4D

16 Performance Groups Chromaticity (continued) Region x y Region x y Region x y Region x y A A2 5A3 5A B B2 5B3 5B C C2 5C3 5C D D2 5D3 5D A A2 6A3 6A B B2 6B3 6B C C2 6C3 6C D D2 6D3 6D A A2 7A3 7A

17 Performance Groups Chromaticity (continued) Region x y Region x y Region x y Region x y B B2 7B3 7B C C2 7C3 7C D D2 7D3 7D A A2 8A3 8A B B2 8B3 8B C C2 8C3 8C D D2 8D3 8D

18 Cree s Standard Chromaticity Regions Plotted on the 1931 CIE Curve ANSI Cool White 5000 K 5700 K CCy K 0S 0B 6500 K 1S 0T 1B 0C 1A 0D 1R 0A 0U 0R 1T 1C 1D 1U 2S 2B 2A 2R 2T 2C 2D 2U 3S 3B 3A 3R ANSI C78.377A CCx Neutral White 0.44 CCy S 3B 3A 3R 5000 K 3U 3D 3C 3T 4R 4A 4B 4S 4U 5R 3500 K 4000 K 6S 4500 K 5T 6C3 6C2 6B3 5S 6C4 5C3 6B2 6C1 5C2 6B4 4T 6D3 5B3 5C4 6B1 6D2 5B2 5C1 6A3 6D4 5B4 5D3 6A2 6D1 4C 5B1 5D2 6A4 5A3 5D4 6A1 5A2 5D1 6U 5A4 4D 5A1 6R 5U ANSI C78.377A 6T CCx 18

19 Cree s Standard Chromaticity Regions Plotted on the 1931 CIE Curve - continued ANSI Neutral White and ANSI Warm White K K CCy B 5000 K 3C 4A 4B 4D 4500 K 4C 5A1 5A2 5B1 5B2 5A4 5A3 5B4 5B3 5D1 5D2 5C K 5C2 5D4 5D3 5C4 6A1 5C3 6A2 6B1 6A4 6B2 6A3 6B4 6D1 6B3 6D2 6C1 6D K 6C2 6D3 6C4 7A1 6C3 7A2 7A4 7B1 7A3 7B2 7D1 7B4 7D2 7B3 7D4 7C1 7D3 8A1 7C2 7C4 8A2 8A4 7C3 8B1 8A3 8D1 8B2 8B4 8D2 8D4 8B3 8C1 8D3 ANSI C78.377A 8C2 8C4 8C3 3D 3A CCx 19

20 Cree s Standard Cool White Kits Plotted on ANSI Standard Chromaticity Regions 5000 K 5000 K 6500 K K 2S 2T 3S 3B 6500 K K 2S 2T 3S 3B CCy 8000 K 1S 1T 1C 2B 2C 2D 3A CCy 8000 K 1S 1T 1C 2B 2C 2D 3A T 0S 0C 0B 0D 0A 0U 0R 1B 1A 1R 1D 1U 2A 2R 2U 3R ANSI C78.377A T 0S 0C 0B 0D 0A 0U 0R 1B 1A 1R 1D 1U 2A 2R 2U 3R ANSI C78.377A CCx CCx 5000 K 5000 K CCy K 6500 K 1S 0T 1B 0S 0C 1A 0B 0D 1R 0A 0U 0R 1T 1C 1D 1U K 2S 2B 2A 2R 2T 2C 2D 2U 3S 3B 3A 3R ANSI C78.377A CCy K 6500 K E1 1S 0T 1B 0S 0C 1A 0B 0D 1R 0A 0U 0R 1T 1C 1D 1U 5700 K 2S 2B 2A 2R 2T 2C 2D 2U 3S 3B 3A 3R ANSI C78.377A CCx CCx 5000 K 6500 K 5700 K E2 2S 2T 3S 3B CCy 8000 K 1S 1T 1C 2B 2C 2D 3A 0T 1B 1D 2A 2U 3R S 0C 0B 0D 0A 0U 0R 1A 1R 1U 2R ANSI C78.377A CCx 20

21 Cree s Standard Warm and Neutral White Kits Plotted on ANSI Standard Chromaticity Regions K CCy E K 3C 3B E4 4A 4B E K E K 8C2 8B3 8B2 7C K 7C2 7B3 7B2 8B4 8C1 8C4 8B K E6 6C3 7C4 7C1 6C2 7B4 8D2 8D3 6B3 7B1 8A3 6C4 5C3 6B2 6C1 5C2 6B4 7A2 7A3 7D2 E5 7D3 8A2 6D3 7D4 8A1 8A4 8D1 8D4 5B3 5C4 6B1 7D1 6D2 7A4 5B2 5C1 6A3 7A1 6D4 5B4 5D3 6A2 6D1 5B1 5D2 4C 6A4 5A3 5D4 6A1 5A2 5D1 5A4 ANSI 4D 5A1 C78.377A 8C3 3D 3A CCx K CCy B 5000 K F4 4B 3C 4A 3000 K 3500 K 8C2 8B3 8B2 7C K 7C2 7B3 7B2 8B4 8C1 8C4 8B K 6C3 7C4 7C1 6C2 7B4 6B3 7B1 6C4 5C3 6B2 6C1 5C2 6B4 7A2 7A3 7D2 7D3 8A2 8A3 8D2 8D3 6D3 7D4 8A1 8A4 8D1 8D4 F5 5B3 5C4 6B1 7D1 6D2 7A4 5B2 5C1 6A3 7A1 6D4 5B4 5D3 6A2 6D1 5B1 5D2 4C 6A4 5A3 5D4 6A1 5A2 5D1 5A4 ANSI 4D 5A1 C78.377A F6 F7 F8 8C3 3D 3A CCx 21

22 Cree s Standard Warm and Neutral White Kits Plotted on ANSI Standard Chromaticity Regions - Continued 0.46 CCy B 3A 5000 K 3D 3C 4A 4B 3000 K 3500 K 8C3 8C2 8B3 8B2 7C K 7C2 7B3 7B2 8B4 8C1 8C4 8B K 6C3 7C4 7C1 6C2 7B4 Z5 6B3 7B1 6C4 5C3 6B2 6C1 5C2 6B4 7A2 7A3 7D2 7D3 8A2 8A3 8D2 8D3 6D3 7D4 8A1 8A4 8D1 8D4 5B3 5C4 6B1 7D1 6D2 7A4 5B2 5C1 6A3 7A1 6D4 5B4 5D3 6A2 6D1 5B1 5D2 4C 6A4 5A3 5D4 6A1 5A2 5D1 5A4 ANSI 4D 5A1 C78.377A Z6 Z7 Z K CCx 22

23 Cree s Standard Chromaticity Kits The following table provides the chromaticity bins associated with chromaticity kits. Color CCT Kit Chromaticity Bins 6200 K 51 0A, 0B, 0C, 0D, 0R, 0S, 0T, 0U, 1A, 1B, 1C, 1D, 1R, 1S, 1T, 1U, 2A, 2B, 2C, 2D, 2R, 2S, 2T, 2U, 3A, 3B, 3R, 3S Cool White 6000 K 53 1A, 1B, 1C, 1D, 1R, 1S, 1T, 1U, 2A, 2B, 2C, 2D, 2R, 2S, 2T, 3A, 3B, 3S 6200 K 50 1A, 1B, 1C, 1D, 2A, 2B, 2C, 2D 6500 K E1 1A, 1B, 1C, 1D 5700 K E2 2A, 2B, 2C, 2D 5000 K E3 3A, 3B, 3C, 3D 4750 K F4 3C, 3D, 4A, 4B Neutral White 4500 K E4 4A, 4B, 4C, 4D 4250 K F5 4C, 4D, 5A1, 5A2, 5A3, 5A4, 5B1, 5B2, 5B3, 5B K E5 5A1, 5A2, 5A3, 5A4, 5B1, 5B2, 5B3, 5B4, 5C1, 5C2, 5C3, 5C4, 5D1, 5D2, 5D3, 5D K Z5 5A3, 5B4, 5C1, 5D K F6 5C1, 5C2, 5C3, 5C4, 5D1, 5D2, 5D3, 5D4, 6A1, 6A2, 6A3, 6A4, 6B1, 6B2, 6B3, 6B K E6 6A1, 6A2, 6A3, 6A4, 6B1, 6B2, 6B3, 6B4, 6C1, 6C2, 6C3, 6C4, 6D1, 6D2, 6D3, 6D K Z6 6A3, 6B4, 6C1, 6D2 Warm White 3250 K F7 6C1, 6C2, 6C3, 6C4, 6D1, 6D2, 6D3, 6D4, 7A1, 7A2, 7A3, 7A4, 7B1, 7B2, 7B3, 7B K E7 7A1, 7A2, 7A3, 7A4, 7B1, 7B2, 7B3, 7B4, 7C1, 7C2, 7C3, 7C4, 7D1, 7D2, 7D3, 7D K Z7 7A3, 7B4, 7C1, 7D K F8 7C1, 7C2, 7C3, 7C4, 7D1, 7D2, 7D3, 7D4, 8A1, 8A2, 8A3, 8A4, 8B1, 8B2, 8B3, 8B K E8 8A1, 8A2, 8A3, 8A4, 8B1, 8B2, 8B3, 8B4, 8C1, 8C2, 8C3, 8C4, 8D1, 8D2, 8D3, 8D K Z8 8A3, 8B4, 8C1, 8D2 23

24 Bin and Order Code Formats XP-G2 bin codes and order codes are configured in the following manner: Order Code Series XPG = XP-G Color specification 01 = Outdoor White B1 = 70 CRI minimum L1 = Standard CRI H1 = 80 CRI minimum P1 = 85 CRI minimum U1 = 90 CRI minimum Bin Code Series XPG = XP-G Color specification 01 = Outdoor White B1 = 70 CRI minimum L1 = Standard CRI H1 = 80 CRI minimum P1 = 85 CRI minimum U1 = 90 CRI minimum SSSCCC-BD-HHHH-NNNNN Kit number Internal code SSSCCC-BD-WWW-FF-G-AA Luminous flux group Internal code Color BWT = Gen 2 White Chromaticity bin Color BWT = Gen 2 White 24

25 Reflow Soldering Characteristics In testing, Cree has found XLamp XP-G2 LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used, and therefore it is the lamp or luminaire manufacturer s responsibility to determine applicable soldering requirements. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. T P Ramp-up t P Critical Zone T L to T P Temperature T L Ts max Ts min ts Preheat t S Ramp-down 25 t 25 C to Peak Time IPC/JEDEC J-STD-020C Profile Feature Lead-Free Solder Average Ramp-Up Rate (Ts max to T p ) 1.2 C/second Preheat: Temperature Min (Ts min ) 120 C Preheat: Temperature Max (Ts max ) 170 C Preheat: Time (ts min to ts max ) seconds Time Maintained Above: Temperature (T L ) 217 C Time Maintained Above: Time (t L ) seconds Peak/Classification Temperature (Tp) C Time Within 5 C of Actual Peak Temperature (tp) Ramp-Down Rate Time 25 C to Peak Temperature seconds 1-6 C/second 4 minutes max. Note: All temperatures refer to topside of the package, measured on the package body surface. 25

26 Notes Measurements The luminous flux, radiant power, chromaticity, forward voltage and CRI measurements in this document are binning specifications only and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors that are not within Cree s control and are not intended or provided as operational specifications for the products. Calculated values are provided for informational purposes only and are not intended or provided as specifications. Pre Release Qualification Testing Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp LEDs and details of Cree s pre-release qualification testing for XLamp LEDs. Lumen Maintenance Cree now uses standardized IES LM and TM methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document. Please read the Long-Term Lumen Maintenance application note for more details on Cree s lumen maintenance testing and forecasting. Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture Sensitivity Cree recommends keeping XLamp LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering. Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity. Once the MBP is opened, XLamp XP-G2 LEDs may be stored as MSL 1 per JEDEC J-STD-033, meaning they have unlimited floor life in conditions of 30 ºC/85% relative humidity (RH). Regardless of the storage condition, Cree recommends sealing any unsoldered LEDs in the original MBP. RoHS Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, RoHS Declarations for this product can be obtained from your Cree representative or from tthe Product Ecology section of the Cree website. REACh Compliance REACh substances of very high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA) has published notice of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative to insure you get the most up-to-date REACh Declaration. REACh banned substance information (REACh Article 67) is also available upon request. 26

27 Notes - Continued UL Recognized Component This product meets the requirements to be considered a UL Recognized Component with Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/UL Vision Advisory WARNING: Do not look at an exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please refer to the LED Eye Safety application note. 27

28 Mechanical Dimensions (T A = 25 C) Thermal vias, if present, are not shown on these drawings All measurements are ±.13 mm unless otherwise indicated OPTICAL REFERENCE 3.45 OPTICAL REFERENCE.50 Top View R Side View 3.30 REF REF. Anode 1.30 Bottom View Anode Alternate Bottom View Recommended PCB Solder Pad Recommended Stencil Pattern (Hatched Area is Open) 28

29 REF Bo Tape and Reel All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard. T 0.30 ± ±0.05 Do Y P2 2.0 ±0.05 (I) Po 4.0 ±0.1 (II) CATHODE SIDE E ±0.1 SECTION Y-Y XLamp XP-G2 LED R0.2 TYPICAL Ko Y D1 1.5 MIN. All dimensions in mm. R REF Bo F(III) W Ao /- 0.1 Bo /- 0.1 Ko /-0.1 F P 1 W / / /-0.1 R0.2 TYPICAL Ko SECTION Y-Y Y D1 1.5 MIN. REF R 2.24 X P1 X REF 0.59 Ao ANODE SIDE (I) (II) (III) (IV) Measured from centerline of sprocket hole to centerline of pocket. Cumulative tolerance of 10 sprocket holes is ± Measured from centerline of sprocket hole to centerline of pocket. Other material available. SECTION X-X Ao /- 0.1 Bo END /- 0.1 Ko /-0.1 F / P /- 0.1 W / ±.1 User Feed Direction (I) Measured from centerline of sprocket hole to centerline of pocket. 4±.1 (II) Cumulative tolerance of 10 sprocket 8± CATHODE SIDE STARTholes is ± ±.10 (III) Measured from centerline of sprocket hole to centerline of pocket. (IV) Other material available Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) ANODE SIDE Loaded Pockets (1000 Lamps) Leader 400mm (min.) of empty pockets with at least 100mm sealed by tape (50 empty pockets min.) Ø Ø61 ± 0.5 OD 7.5'' MEASURED AT HUB Ø MEASURED AT INSIDE EDGE 29

30 Packaging Unpackaged Reel Label with Cree Bin Code, Quantity, Reel ID Packaged Reel Label with Cree Order Code, Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Boxed Reel Label with Cree Order Code, Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Patent Label (on bottom of box) 30