PRA/182000, PRA/182000/M ISO/VDMA Profile cylinders
|
|
- Byron Lamb
- 6 years ago
- Views:
Transcription
1 P/182000, P/182000/M IO/VDM Profile cylinders onforms to IO 15552, IO 6431, VDM and NFE Profile barrel with concealed tie rods High performance, stability and reliability Polyurethane seals ensure efficient low friction operation and long life witches can be mounted flush with the profile barrel TEHNIL DT Medium: ompressed air, filtered, lubricated or non-lubricated Operation: P/182000: djustable cushioning P/182000/M: Magnetic piston, adjustable cushioning Operating pressure: bar Operating temperature: max. onsult our Technical ervice for use below +2 MTEIL Profile barrel: anodized aluminium End covers: pressure diecast aluminium Piston rod: stainless steel (Martensitic) Piston rod seals: polyurethane Piston seals: polyurethane O-rings: nitrile rubber TNDD MODEL Ø Piston rod Ø Port size MODEL Non-magnetic Magnetic Magnetic non-rotating EOIE eed switch with integral 5m cable anjo flow control traight fitting Tube diameter in bold Elbow fitting ervice kit Non-magnetic Magnetic /8 P/182032/* P/182032/M/* P/182032/N2/* M/50/LU/5V 0K Q/8032/ /4 P/182040/* P/182040/M/* P/182040/N2/* M/50/LU/5V 0K Q/8040/ /4 P/182050/* P/182050/M/* P/182050/N2/* M/50/LU/5V 0K Q/8050/ /8 P/182063/* P/182063/M/* P/182063/N2/* M/50/LU/5V 0K Q/8063/ /8 P/182080/* P/182080/M/* P/182080/N2/* M/50/LU/5V 0K Q/8080/ /2 P/182100/* P/182100/M/* P/182100/N2/* M/50/LU/5V 0K Q/8100/ /2 P/182125/* P/182125/M/* M/50/LU/5V 0K Q/8125/00 * Insert stroke length in mm For information on additional magnetic switches see page Other fittings are available, please see section 7 tandard strokes Ø Other strokes available For further information
2 OPTION ELETO P /182 / / Non-standard variants High temperature version: 150 max. Hydraulic (Ø mm) Piston rod material tainless steel martensitic Hard chromium plated tainless steel austenitic T H ylinder Ø Variants (magnetic piston) tandard pecial wiper/seal low friction Piston rod Without cushion Without cushion, low friction and special wiper/seal Four-positon cylinder Non-rotating piston rod (internal) Locking unit (passive) arrel turned at 90 (for use with guideblocks Q/8000/51 and.../61) Extended piston rod P*/182***/MU/****/*** /W6/ M W2 X2 M MW X4 JM W4 MT N2 L4 MIL MU Extension (mm) trokes (mm) 3000 max. Variants (non-magnetic piston) tandard None pecial wiper/seal W1 Low friction X1 Piston rod Without cushion W Without cushion, low friction X3 J special wiper/seal W3 Four-positon cylinder IT Non-rotating piston rod (internal) N1 Locking unit (passive) L2 arrel turned at 90 (for use with guideblocks Q/8000/51 and.../61) IIL Extended piston rod IU P*/182***/IU/****/*** /W5/ Extension (mm) Note: If option is not required, disregard option position within part number eg. /182100/M/100. For combinations of cylinder variants consult our technical service. Please note that heat resistant seals are not available for all variants. This options selector explains only the cylinder variants. dditional variants/options are not possible
3 P/182000, P/182000/M IO/VDM Profile cylinders MOUNTIN anjo U W uide block D D2 U UH FH UH K UF F eed switch FH Ø K, D D2 F FH 32 QM/8032/35 QM/8025/38 Q/8032/22 Q/8032/21 Q/8032/23 Q/8032/42 QM/8025/25 Q/8032/34 40 QM/8032/35 QM/8040/38 Q/8040/22 Q/8040/21 Q/8040/23 Q/8040/42 QM/8040/25 Q/8040/34 50 QM/8050/35 QM/8050/38 Q/8050/22 Q/8050/21 Q/8050/23 Q/8050/42 QM/8050/25 Q/8050/34 63 QM/8050/35 QM/8050/38 Q/8063/22 Q/8063/21 Q/8063/23 Q/8063/42 QM/8050/25 Q/8063/34 80 QM/8080/35 QM/8080/38 Q/8080/22 Q/8080/21 Q/8080/23 Q/8080/42 QM/8080/25 Q/8080/ QM/8080/35 QM/8080/38 Q/8100/22 Q/8100/21 Q/8100/23 Q/8100/42 QM/8080/25 Q/8100/ QM/8125/35 QM/8125/38 QM/8125/22 QM/8125/21 QM/8125/23 Q/8125/42 QM/8125/25 Q/8125/34 Ø W UF UH U U 32 Q/8032/27 Q/8032/41 M/P19931 M/P19493 QM/8025/32 PQ/182032/40 Q/8032/33 M/P Q/8040/27 Q/8040/41 M/P19932 M/P19494 QM/8040/32 PQ/182040/40 Q/8040/33 M/P Q/8050/27 Q/8040/41 M/P19933 M/P19495 QM/8050/32 PQ/182050/40 Q/8050/33 M/P Q/8063/27 Q/8063/41 M/P19934 M/P19496 QM/8050/32 PQ/182063/40 Q/8063/33 M/P Q/8080/27 Q/8063/41 M/P19935 M/P19497 QM/8080/32 PQ/182080/40 Q/8080/33 M/P Q/8100/27 Q/8100/41 M/P19936 M/P19498 QM/8080/32 PQ/182100/40 Q/8100/33 M/P QM/8125/27 Q/8100/41 M/P19937 M/P19499 QM/8125/32 PQ/182125/40 QM/8125/33 M/P71355 For details of mountings see page uide blocks Ø MODEL MODEL 32 Q/8032/51/* Q/8032/61/* 40 Q/8040/51/* Q/8040/61/* 50 Q/8050/51/* Q/8050/61/* 63 Q/8063/51/* Q/8063/61/* 80 Q/8080/51/* Q/8080/61/* 100 Q/8100/51/* Q/8100/61/* * Insert stroke length in mm from table on the right. For details of guide blocks see page Note: Q/8 _/51* = Plain bearing. Q/8 _/61* = all bearing. tandard strokes for guide block Ø Other stroke lengths are not available, use nearest standard stroke. Maximum stroke 500 mm
4 I DIMENION P/ WH L8 + # - M KW L 2 VD L 12 PL EE 1 PL EE V E ø e 11 KK P ø e 11 MM h 9 KV W L 9 T H T H ø mm 1 ushion screw MODEL Ø M P Ø e11 Ø e11 H E EE KK KV KW L2 P/182032/ , /8 27,5 M10x1, P/182040/ , /4 32 M12x1, P/182050/ /4 31 M16x1, P/182063/ /8 33 M16x1, P/182080/ , /8 33 M20x1, P/182100/ /2 37 M20x1, P/182125/ /2 46 M27x ,5 45 MODEL Ø L8 L9 L12 Ø MMh9 PL T W V VD WH at 0 mm per 25 mm P/182032/ ,5 M ,51 kg 0,06 kg P/182040/ , M , ,80 kg 0,08 kg P/182050/ ,5 46,5 M , ,33 kg 0,12 kg P/182063/ ,5 M ,80 kg 0,13 kg P/182080/ M ,25 kg 0,20 kg P/182100/ M ,81 kg 0,23 kg P/182125/ M ,5 65 8,00 kg 0,33 kg 1-065
5 P/182000, P/182000/M IO/VDM Profile cylinders YLINDE VINT P/182000/J, P/182000/JM ylinder with double ended piston rod MODEL Ø ZM L8 P/182032/J P/182040/J P/182050/J P/182063/J P/182080/J P/182100/J P/182125/J ZM + 2 x # L 8 + # P/182000/N1, P/182000/N2 ylinder with non-rotating piston rod MODEL Ø Max. torque P/182032/N ,5 Nm P/182040/N ,0 Nm P/182050/N ,5 Nm P/182063/N ,5 Nm P/182080/N ,5 Nm P/182100/N ,5 Nm - P/182000/IT, P/182000/MT Four-position cylinder MODEL Ø L 8 L 10 L 11 P/182032/.T P/182040/.T P/182050/.T P/182063/.T P/182080/.T P/182100/.T P/182125/.T L 10 + #1 + #2 L 8 + #1 L11 L 8 + #2 P/182000/, P/182000/M Piston rod MODEL Ø Ø Max. stroke per Piston rod extension for first P/182032/ P/182040/ P/182050/ P/182063/ P/182080/ P/182100/ P/182125/ for further ø 1-066
PRA/822000/M, PRA/ Smoothline cylinder Magnetic or non-magnetic piston, double acting
P/822000/M, P/822000 Smoothline cylinder > 32... 00 mm > Cylinder and mounting conform to ISO 5552 > eed or solid state switches can be mounted flush with the profile barrel > lternative air ports as standard
More informationPRA/182000, PRA/182000/M
Profile cylinders conforms to ISO 15552 Non-magnetic and magnetic piston Double acting Ø 32 to 125 mm High performance, stability and reliability M/50 switches can be mounted flush with the profile Cylinders
More informationPRA/842000/M, PRA/ Clean Line cylinder Magnetic or non-magnetic piston, double acting
> > 32... 00 mm > > Cylinder and mounting conform to ISO 5552 > > Smooth and spherical Corrosion resitant design conforms to N 672-2, accepted in the food industry > > Special PU seals provide high performance
More informationRA/8000, RA/8000/M. Pneumatic cylinders ISO 6431, VDMA and NFE Non-magnetic and magnetic piston Double acting Ø 32 to 320 mm
Pneumatic cylinders ISO 6431, VDMA 456 and NFE 49-003-1 Non-magnetic and magnetic piston Double acting Ø 3 to 30 mm Comprehensive range for the utmost versatility Conforms to DIN ISO 6431, VDMA 456 and
More informationRA/192000/M. Compact cylinder ISO Magnetic piston, double acting Ø 20 to 125 mm
Compact cylinder ISO 2287 Magnetic piston, double acting Ø 20 to 25 mm Conforms to ISO 2287 M/50 switches can be mounted flush with the profile Magnetic piston as standard Seals ensure low friction operation
More informationPRA/181000, PRA/181000/M PRA/183000, PRA/183000/M
PA/181000, PA/181000/M M/50 switches can be mounted flush with the profile Conforms to DIN ISO 6431 and VDMA 24562 part 1 Mountings conform to DIN ISO 6431, VDMA 24562 part 2 and NFE 49-003-1 Polyurethane
More informationPRA/181000, PRA/181000/M PRA/183000, PRA/183000/M
PA/181000, PA/181000/M PA/183000, PA/183000/M Profile barrel with concealed tie rods Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic Piston Single Acting 32 to 100 mm
More informationStrokes (mm) N/en
IVC cleanline Cylinder double acting, magnetic piston 32... 100 mm Cylinders and mountings conform to ISO 15552 Complete functional unit with LED display Central electrical connector, polarity-safe Integrated
More informationLRA/8000/M/EX, LRA/8000/EX, ISO cylinder Magnetic & Non-magnetic piston, double acting
> > Ø 32... 320 mm > > Comprehensive range for the utmost versatility > > Wide temperature range > > Supplied complete with piston rod locknut > > Conforms to ISO 15552 (ISO 6431, VDM 24562 and NFE 49-003-1)
More informationLPRA/182000/M, ISO cylinder Magnetic piston, double acting
> > Ø 32... 125 mm > > High performance, stability and reliability > > M/50 switches can be mounted flush with the profile > > Cylinders and mountings conform to ISO 15552 (ISO 6431, VDM 24562 and NFE
More informationLPRA/182000/M Double acting profile cylinders Ø mm
Double acting profile cylinders 32... 125 mm High performance, stability and reliability M/50 switches (solid state) can be mounted flush with the profile Cylinders and mountings conform to ISO 15552 (ISO
More informationRA/28000, RA/ Pneumatic Cylinders ISO 6431, VDMA and NFE Non-magnetic and Magnetic, Single Acting 32 to 100 mm
Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic, Single Acting 32 to 100 mm ugged tie rod construction Polyurethane seals ensure efficient low friction operation and
More informationRM/28000/M Roundline cylinders (ISO)
RM/28000/M Roundline cylinders (ISO) Single acting, ISO 6432 - Ø 10... 25 mm Magnetic piston as standard enerally conforms to ISO 6432 High strength, double crimped end cap design Corrosion resistant Nose
More informationOur policy is one of continued research and development. We therefore reserve the right
Corrosion resistant design Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Magnetic Piston Double Acting Ø 32 to 100 mm Accepted in the Food Industry Conforms to ISO 6431, VDMA 24562 and NFE
More informationKA/8000, KA/8000/M. Cylinder Variants. Model Codes. Standard Strokes. Warning 7/97 N/UK
Stainless Steel VDMA/ISO Cylinders Non-magnetic and magnetic Piston Double Acting Ø 32 to 200 mm High corrosion and acid resistant Conforming to Standards ISO 6431, VDMA 24562 and NFE 49-003-1 Ideal for
More informationACT-74. Short stroke cylinders DC/91000/M, DC/93000/M Single acting Ø mm. Actuators DC/9 / /
Actuators Short stroke cylinders DC/91000/M, DC/93000/M Single acting Ø 12... 63 mm One third the basic length of a corresponding ISO/VDMA model Low friction, long life seal design Fully non-corrodible
More information12/95 N Our policy is one of continued research and development. We therefore reserve the right
Pneumatic Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic, Double Acting 32 to 125 mm Cylinders to VDMA Standard 24562, ISO 6431 and NFE 49-003-1 New polyurethane seals ensure
More informationM/ Rotary cylinders Rack & pinion version Magnetic or non-magnetic piston Double acting Ø 32 to 125 mm
otary cylinders ack & pinion version Magnetic or non-magnetic piston Double acting Ø 32 to 25 mm Suitable torques from,2 to 5,0 Nm/bar otation angles 90, 80, 270, 360 Adjustable cushioning Male and female
More informationPRA/182000, PRA/182000/M
Profile barrel with concealed tie rods Pneumatic Profile Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic Piston Double Acting Ø 32 to 125 mm M/50 Switches can be mounted flush
More informationRM/900/M Heavy duty cylinders Ø 1 1/4... 4
Heavy duty cylinders Ø 1 1/4... 4 Heavy duty cylinder ideal for a wide range of rail applications Extensive range of mountings Rugged, reliable long established design Magnetic piston as standard Mounting
More informationACT-72. DA/8000 Double acting Ø mm
ISO/VDMA Cylinders DA/8000 Double acting Ø 32... 320 mm Conforms to ISO 6431, VDMA 24562 and NFE 49-003-1 High performance, ruggedness and reliability Extensive range of mountings Technical data Medium:
More informationPRA/182000, PRA/182000/M
Profile barrel with concealed tie rods Pneumatic Profile Cylinders ISO 6431, VDMA 24562 and NFE 49-003-1 Non-magnetic and Magnetic Piston Double Acting Ø 32 to 125 mm M/50 Switches can be mounted flush
More informationPVA/182000, PVA/182000/M
Smooth Line cylinders with or without integrated switches Double acting Ø 3... 100 mm Smooth and spherical profile design with concealed tie rods Special polyurethane wiper seal Body sealing conforms to
More informationOur policy is one of continued research and development. We therefore reserve the right to amend,
Airmotor (Oscillator) with integrated switches Double acting Ø 50... 100 mm Complete functional unit for oscillating movement Conforms to ISO 6431 and VDMA 24562 Integrated 5/2 valve Frequency and speed
More informationLRM/55401/M, Roundline cylinder Magnetic piston, double acting
LRM/5540/M, Roundline cylinder > > 3... 00 mm > > Clean line design > > Low friction, long life seals > > Standard magnetic piston for full control system versatility > > Non-lube operation > > Shock and
More informationStandards ISO Max. particle size 50 µm. Pressure for determining piston forces. Materials: Polyurethane
Ports: - double-acting with magnetic piston Cushioning: elastic Piston rod: external thread 1 Standards ISO 21287 Compressed air connection Internal thread Working pressure min./max. 1 bar / 10 bar Ambient
More information10/97 N Our policy is one of continued research and development. We therefore reserve the right
ISO Cylinders Magnetic Piston Double Acting Ø 10 to 25 mm Magnetic piston as standard Conforming to ISO 6432 Corrosion resistance Buffer and adjustable cushioned models Supplied complete with nose mounting
More informationPRA/801000, PRA/803000, RA/801000, RA/ ISOLine cylinder, single acting
PR/80000, PR/80000, R/80000, R/80000 > ø 2... 00 mm > High performance adaptive cushioning system CS > High performance, stability and reliability Technical features Medium: Compressed air, filtered, lubricated
More informationAvailable: Cylinders till july 2000 Spares till july /98 N
Available: Cylinders till july 2000 RM/55400/M Roundline Cylinders Magnetic Piston Double Acting 32 to 100 mm bore Magnet piston as standard provides a wide range of control options Attractive clean- line
More informationISO 6432 Ø mm. Page 9. Ø mm. RM/91000/M, RM/93000/M Ø mm. Ø mm ISO, VDMA, NFE. ISO, VDMA, NFE Ø 32...
Actuators Product selector table...2 Single acting cylinders Miniature roundline cylinders ( 2,5 & 4 mm)...9 ISO Roundline ( 10 to 25 mm)...10 Roundline ( 8 to mm)...20 VDMA compact ( 20 to 63 mm)...32
More informationPRA/882000/M/EX, IVAC Clean Line cylinder Magnetic piston, double acting
> ø 3... 100 mm > Complete functional unit with LED display > TEX-zones depending on pilot control: zones &, II 3GD, Valve control module (VCM) zones 1 & 1, II GD, Pilot control on separate specification
More informationRM/57200/M, RT/57200/M
Roundline Cylinders Magnetic Piston Double Acting Ø 8 to 63 mm Three different basic versions provide flexibility and wide range of application Magnetic piston as standard provides a wide range of control
More informationOur policy is one of continued research and development. We therefore reserve the right 1/98 N
ISO Cylinders Magnetic Piston Single Acting Ø 10 to 25 mm Magnetic piston as standard Conforming to ISO 6432 Corrosion resistance Nose mounting nut and piston rod locknut as standard Technical Data Medium:
More informationAssociated ranges. Body material. Stainless steel Aluminium
Associated ranges Series Body material Stainless steel Aluminium KA/8000,.../M Stainless steel tie-rod cylinders (ISO/VDMA) Double acting Ø 32 to 200 mm 216 KM/8000/M Stainless steel roundline cylinders
More information2. COMPACT CYLINDERS series STRONG (RS, RQ)
2. COMPACT CYLINDERS series STRONG (RS, RQ) A new series of compact cylinders for long s and heavy-duty applications standard supplied with oversized guides and rods, the first one with adjustable pneumatic
More informationOur policy is one of continued research and development. We therefore reserve the right 10/99 N
Stainless Steel ISO Cylinders Magnetic Piston Double Acting Ø 12 to 25 mm High corrosion and acid resistance Magnetic piston as standard Conforming to ISO 6432 Suitable for applications in the Food Industry
More informationM/1000, Heavy Duty Cylinders Double Acting
> > Ø 2 to 12 (50 to 305 mm) > > Extremely rugged heavy duty construction - ideal for use in the most arduous conditions. > > Large range of bore sizes - ideal for a wide variety of industrial applications.
More informationACT-132. DC/91000/M, DC/93000/M Single acting Ø mm DC/9 / /
Series 90000 ompact Actuators D/91000/, D/93000/ Single acting Ø 12... 63 mm ne third the basic length of a corresponding IS/VDA model ow friction, long life seal design Fully non-corrodible specification
More informationM/146000, M/146100, M/146200
LINTR PLUS rodless cylinders Magnetic piston and non-magnetic piston Double acting Ø 3 to 50 mm New lightweight design extrusion with universal mounting grooves Proved and patented sealing system Dust
More informationCylinders ISO Bores from 32 to 125 mm
Cylinders ISO 5552 ores from 32 to 25 mm Double acting Standard executions Version Profile Tube Symbol Type STANDARD MAGNETIC AMA AMT For the magnetic reed switches type ASV and ASC see from page.0.. For
More informationCylinders DIN ISO 6431 and VDMA Bores from 32 to 125 mm
Double acting Standard executions Version Shape of barrel Symbol Type MAGNETIC STANDARD AMA AMT 1 For the magnetic reed switches type ASV see from page 1.110.1. For coupling cylinders/reed swiches/brackets
More informationM/46800/M, M/46800/HM, M/46800/PM
External guides for heavy loads over long distances Rigid, reinforced aluminium profile provides greater load support T-slots in the outer profile enable individual mounting options Precision guidance
More informationSeries ICS and ICL Pneumatic Cylinders. Corrosion resistant stainless steel and aluminum cylinders
Series ICS and ICL Pneumatic Cylinders Corrosion resistant stainless steel and aluminum cylinders Series ICS and ICL cylinders New generation of stainless steel and clean line cylinders. Series ICS from
More information1/96 N Our policy is one of continued research and development. We therefore reserve the right
Roundline Cylinders Magnetic Piston Double cting 8 to 63 mm Very compact and shorter than the basic length of a corresponding ISO/VDM and roundline cylinder. Magnetic piston as standard provides a wide
More informationTie rod cylinders, Series 523
Electric Drives and Controls Hydralics Linear Motion and Assembly Technologies Pneumatics Service Tie rod cylinders, Series 523 Technical data Tie rod cylinders, Series 523 Grey series, 32 25 mm ( /4"-5")
More informationNEN Series NFPA Aluminum Cylinders
NEN Series NP luminum ylinders 1-1/2" to 4" bore sizes ompetitively priced Magnetic piston standard djustable cushion standard Sleeve nut construction standard Stocked strokes Technical data Medium: iltered
More informationStandards NFE Max. particle size 50 µm. Pressure for determining piston forces. Materials:
Piston rod cylinders Short-stroke and compact cylinders 1 Standards NFE 49004 Compressed air connection Internal thread Ambient temperature min./max. -20 C / +80 C Medium temperature min./max. -20 C /
More informationStandards NFE Max. particle size 50 µm. Pressure for determining piston forces. Materials:
Ports: - double-acting with magnetic piston Cushioning: elastic Piston rod: Internal thread, 1 Standards NFE 49004 Compressed air connection Internal thread Ambient temperature min./max. -20 C / +80 C
More informationACTUATORS equipment engineering advantage
www.norgren.com/rail RAILINE PNEUMATIC MOTION & FLUID CONTROL SOLUTIONS YOU CAN SEE OUR THINKING engineering advantage ACTUATORS valves pressure switches AND transducers air line equipment fittings tubing
More information1.134 L INEAR A CTUATOR: AIR C YLINDER S ERIES C95
1.134 L INEAR A CTUATOR: AIR C YLINDER H O W M ADE I N USA T ECHNICAL T O O R D E R C95 AIR C YLINDERS C95 P ISTON R OD S Basic K Non-Rotating P ISTON - Basic D Magnetic B ORE IN MM 50 63 80 100 B S T
More informationAIR CYLINDER Series A23, A24
A23 - Magnetic A24 - Non-magnetic Double Acting s (Square type) Ø32-125 mm As per ISO 15552 / VDMA 24562 standards. Features Adjustable cushioning at both ends with elastomer pads Wide varieties of mountings
More informationSERIES PRA AND TRB ISO PNEUMATIC CYLINDERS
SERIES PRA AND TRB ISO 15552 PNEUMATIC CYLINDERS Series PRA and TRB Pneumatic ISO 15552 Cylinders The next generation of ISO cylinders from AVENTICS The Series PRA and TRB cylinder series represent consistent
More informationAIR CYLINDER Series A25, A26
A25 - Magnetic A26 - Non-magnetic S Double End Double Acting - Ø32-100 mm As per ISO 15552 / VDMA 24562 standards Features Adjustable cushioning at both ends with elastomer pads Wide varieties of mountings.
More informationISOCLAIR ROUND CYLINDERS Ø 8 to 25 mm - single acting ISO 6432-CETOP-AFNOR
ISOCLAIR ROUND CYLINDERS to mm - single acting ISO 6432-CETOP-AFNOR FEATURES Good resistance to corrosive elements (barrel and stainless steel rod) SER SES Series 435 Type C-AS C-AS/DM GENERAL Detection
More informationAluminium profile. TANDEM: Double thrust and traction forces. LOW FRICTION: Friction force reduced by over 40%
CATALOGUE > Release 8.7 > Series 6 cylinders Series 6 cylinders - Aluminium profile Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40,
More informationAluminium tube and profile
> Series 63 cylinders CATALOGUE > 206 Series 63 cylinders - Aluminium tube and profile New Single and double-acting, magnetic, cushioned Versions: standard, low friction, high and low temperatures ø 32,
More informationISOCLAIR ROUND CYLINDERS Ø 8 to 25 mm - single acting ISO 6432-CETOP-AFNOR
ISOCLAIR ROUND CYLINDERS to mm - single acting ISO 6432-CETOP-AFNOR FEATURES Good resistance to corrosive elements (barrel and stainless steel rod) GENERAL Detection Equipped or not for magnetic position
More informationPNEUMATIC CYLINDERS CYLINDERS ISO solutions SERIES 21 SERIES 21 CYLINDERS ISO 15552
PNEUMATIC CYLINDERS 1 2 3 4 SERIEs 21- General Information 32-100 mm diameter 21 series cylinders are manufactured to ISO 15552 standard which specifies interchangeable mounting dimensions. The cylinder
More informationAIR CYLINDER Series A75, A76
A76 - n-magnetic A75 - Magnetic AIR CYLINDER Round s - Ø32, 40, 50 and 63 mm Double Acting with Adjustable Cushioning Features Available in magnetic and n magnetic version Adjustable cushioning at both
More informationMax. particle size 5 µm. Pressure for determining piston forces. Materials:
Rodless cylinders Rodless cylinder 1 Working pressure min./max. 2 bar / 8 bar Ambient temperature min./max. -10 C / +60 C Medium Compressed air Max. particle size 5 µm Oil content of compressed air 0 mg/m³
More informationVERSION 1 / Basic cylinder T Double push tandem R Through rod F Hollow through rod. VERSION 2 D Double acting S Single acting front spring
Compact cylinders to AFNOR NF E49-004- DESCRIPTION Cylinders series BU are available from Ø 20 to Ø 00 and, complying with AFNOR NF E49-004-, they re interchangeable also without using anchorages. Besides
More informationStandard strokes (for all diameters) Stroke tolerance (ISO 15552)
Series 19-192 Cylinders according to standard ISO 12 COIHT Construction characteristics nd plates Rod Barrel Rod-guide bushing Piston Seals Cushion adjusting screws die-casting aluminium C chromed steel
More informationAluminium profile. Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100 mm
> Series 62 cylinders CATALOGUE > Release 8.6 Series 62 cylinders - Aluminium profile Double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00 mm»» In compliance with ISO 5552 standards and with the
More informationSeries 63 ISO cylinders
Series 63 ISO 15552 cylinders New versions Single and double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 100, 125 mm In compliance with the ISO 15552 standard Weight reduced by 25% Low noise More
More informationMechanically Jointed Rodless Cylinder High Precision Guide Type. How to Order 16 G 300 L M9N. Stroke. Refer to Standard Stroke table.
Mechanically Jointed Rodless ylinder igh Precision uide Type eries MY/T ø, ø, ø T MY uide type igh precision guide with single axis igh precision guide with double axis ymbol Nil TN TF Type M thread Rc
More informationCylinders Series 61 - Aluminium profile
CATALOGUE > Release 8. Cylinders Series 6 - Aluminium profile MOVEMENT > Cylinders Series 6 Single, double-acting, magnetic, cushioned ø 32, 40, 50, 63, 80, 00, 25 (ISO 5552)» ISO 5552 (corresponding to
More informationAIR CYLINDER Series A12, A13
A12 - Non magnetic A13 - Magnetic S Double Acting ( Ø32-100 ) mm As per ISO 6431 / CETOP RP43P, RP53P standards Features Adjustable cushioning at both ends Wide varieties of mountings Low friction Long
More informationShort-stroke cylinder, Series KHZ Ports: M5 - G 1/4 Single-acting, retracted without pressure Cushioning: elastic Piston rod: Internal thread
: - G 1/4 Single-acting, retracted without pressure Cushioning: elastic Piston rod: Internal 1 Compressed air connection Internal Ambient temperature min./max. -25 C / +80 C Medium temperature min./max.
More informationTwin Rod Non Rotate Cylinders RDV and AZ
Twin Rod Non Rotate Cylinders RDV and AZ A range of twin rod cylinders designed for use in non rotate applications specifially suited to the handling and packaging environments. Offering a range of double
More informationShort-stroke cylinder, Series SSI Ports: M5 - G 3/8 double-acting with magnetic piston Cushioning: elastic Piston rod: Internal thread
Ports: - G 3/8 double-acting with magnetic piston Cushioning: elastic Piston rod: Internal thread 1 Standards ISO 15524 Compressed air connection Internal thread Ambient temperature min./max. - C / +80
More informationSingle and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40, 50, 63, 80, 100, 125mm
CATALOGUE > Release 8.8 > Series 60 cylinders Series 60 cylinders Single and double-acting, magnetic, cushioned Standard, low friction, low temperatures and tandem versions ø 32, 40, 50, 63, 80, 00, 25mm»»
More informationSingle and double-acting, magnetic, cushioned Standard, low friction and low temperature versions ø 32, 40, 50, 63, 80, 100, 125mm
CATALOGUE > Release 8.6 > Series 60 cylinders Series 60 cylinders New version Single and double-acting, magnetic, cushioned Standard, low friction and low temperature versions ø 32, 40, 50, 63, 80, 00,
More informationGuide blocks for ISO/VDMA cylinders
Actuators Guide blocks or ISO/VDMA cylinders QA/8/51/ QA/8/61/ QA/8/81/ (long coupling) QA/8/85/ (short coupling) Ø 32 to 1 mm QA/8/61/ QA/8/51/ Conorms to ISO 6431, VDMA 24562 and NFE 49 3 1 Ensures protection
More informationConstruction characteristics. Technical characteristics. End plates Rod Barrel Rod-guide bushing Piston
Construction characteristics nd plates Rod Barrel Rod-guide bushing Piston Seals Cushion adjusting screws die-casting aluminium C3 chromed steel or stainless steel aluminium alloy anodised spheroid bronze
More informationANTI-CORROSIVE CYLINDERS WITH TIE RODS Ø 32 to 125 mm - double acting - ISO with adjustable pneumatic cushioning
ANTI-CORROSIVE CYLINDERS WITH TIE RODS 32 to 125 mm - double acting - ISO 15552 with adjustable pneumatic cushioning NS Series S FEATURES The cylinders are designed for use in corrosive environments: chemical,
More informationExtruded Body Cylinders, ISO 6431, ISO compliant Series 61
1 ISO / VDMA Cylinders NORTH AMERICAN CYLINDER & ACTUATOR CATALOG > Release 8.5 Extruded Body Cylinders, ISO 6431, ISO 15552 compliant Series 61 Single or double-acting, magnetic, cushioned Standard and
More informationM/146000/EX, M/146100/EX, M/146200/EX, LINTRA PLUS cylinder Magnetic & Non-magnetic piston, double acting
M/46000/X, M/4600/X, M/4600/X, LINTR PLUS cylinder > Ø 6... 80 mm > New lightweight design extrusion with universal mounting grooves > Proved and patented sealing system > Interchangeability with series
More informationBore ø 32, 40, 50, 63, 80, 100, 125 Ports 32 = 1/8, 40/50 = 1/4, 63/80 = 3/8, 100/125 = 1/2
6 S E R I E S Cylinders Series 6 Catalog 2006 Single, double acting, magnetic (DIN/ISO 643) Bore: ø 32, 40, 50, 63, 80, 00, 25 cushioned [ /4, 9/6, 2, 2 /2, 3 /8, 4, 5 inch approximations] The Series 6
More informationTECHNICAL CHARACTERISTICS
2 or 3-stage telescopic pneumatic cylinder Considering its high technological contents, this cylinder series represents without doubt the product with the highest degree of technical research and evolution
More informationProfile Design Air Cylinder
Profile Design Air Cylinder Series CP5 ø, ø, ø, ø, ø, ø Features Conforms to VDMA 24 562 (parts 1 and 2), ISO 6431 and CETOP standards. Combines lightweight profile barrel design with enclosed tie rods
More informationPneumatic cylinders series CX Double acting with magnetic piston, ISO 15552, stainless steel G1/8 to G1/2 piston Ø 32 to 100 mm
Pneumatic cylinders series CX Double acting with magnetic piston, ISO 15552, stainless steel 000 400 Order code CX-032-0250-000 Note: Piston Ø 125, 160 and 200 on request. Series Piston Ø Stroke length
More informationISO CYLINDERS Ø ACTUATORS
ISO 15552 CYLINDERS Ø 250-320 1 Cylinders made to ISO 15552 available in various versions and with a wide range of accessories: double-acting single-or through-rod with or without cushioning configuration
More informationDouble-acting, magnetic, cushioned ø16, 25, 32, 40, 50, 63, 80
> Cylinders Series 50 CATALOGUE > Release 8.5 Rodless cylinders Series 50 Double-acting, magnetic, cushioned ø6, 25, 32, 40, 50, 63, 80»» Four ports on each chamber»» Possibility to supply both chambers
More informationTELESCOPIC CYLINDERS ø mm Series RT
TELESCOPIC CYLINDERS 25 63 mm Series RT The overall dimensions are one of the most imporant aspects: in comparison with a traditional ISO cylinder of the same a reduction in size of approx. 45% (with a
More informationAluminium profile. Double-acting, cushioned, magnetic ø mm
> Series 4 cylinders Series 4 cylinders - Aluminium profile Double-acting, cushioned, magnetic ø 60-200 mm»» In compliance with ISO 643/ VDMA 24562 standards»» Rolled stainless steel rod»» Adjustable pneumatic
More informationProfile cylinders Euromec, Series 168
Electric Drives and Controls Hydralics Linear Motion and Assembly Technologies Pneumatics Service Profile cylinders Euromec, Series 68 Technical data Profile cylinders Euromec, Series 68 Double-acting,
More information-H- Note. -N- Diameters. -T- Stroke lengths. -W- Note. Standard cylinders DNU/DNUL to ISO 6431 Key features at a glance Festo AG & Co.
Standard cylinders DNU/DNUL to ISO 6431 Key features at a glance ISO and standard cylinders DNU/DNUL -H- Note For new applications use type DNC ( -54). -N- Diameters 32... 125 mm -T- Stroke lengths 10...
More informationStandard cylinders DNG/DNGZS, ISO 15552
Features Brief description Double-acting For contactless position sensing With adjustable end-position cushioning at both ends Robust tie rod design Standards-based cylinders to ISO15552 (corresponds to
More informationRT2 RT3. ORIGINAL UNIVER Original design and technology. INDUSTRIALIZED Industrialized components and advanced technology
RT Telescopic cylinders RT2 2 stages 25 mm ORIGINAL UNIVER Original design and technology INDUSTRIALIZED Industrialized components and advanced technology REDUCED DIMENSIONS 60% less than standard cylinders
More informationTie-rod Cylinders, ISO 6431, ISO compliant Series 60
Tie-rod Cylinders, ISO 6431, ISO 15552 compliant Series 60 Single or double-acting, magnetic, cushioned Standard and low friction versions ø 32, 40, 50, 63, 80, 100, 125 mm In compliance with ISO 15552
More informationA44000, LINTRA-LITE Rodless Cylinders Non-magnetic and Magnetic Piston, double acting
> > Ø 25... 40 mm > > New compact, spacesaving design > > Proven sealing system > > Integral switch mounting > > uffer or adjustable cushioning > > Standard foot mountings Technical features Medium: Compressed
More informationISO Technical details
Cylinders > piston rod cylinders > assembly groups > BP IO 15552 Technical details Operating pressure Cylinder with brake system XBP brake system 3... 6 bar Temperature range -10 C... +50 C Max. stroke
More informationISO CYLINDERS SERIES HCR (High Corrosion Resistance) ACTUATORS
ISO 15552 CYLINDERS SERIES HCR (High Corrosion Resistance) 1 ISO 15552 CYLINDERS SERIES HCR (High Corrosion Resistance) In some applications, the cylinders are exposed to aggressive environments (e.g.
More informationHinge cylinders DW Key features
Key features At a glance Hinge cylinder for clamping components during the welding process Easy assembly thanks to swivel bearing on the bearing cap Integrated flow control Integrated end-position cushioning
More informationClimax Pneumatics Cnomo NFE Cylinders
Climax Pneumatics Cnomo NFE 49001 Cylinders End Caps Tube Tie Rods Seals Piston Rod Diecast Aluminum Anodized Aluminum Zinc Coated or Stainless Steel Polyurethane Chromium Coated Steel Working Pressure
More informationPneumatic cylinders, piston-ø mm Double acting with magnetic piston DIN ISO 15552
Pneumatic cylinders, piston-ø 32 100 mm Double acting with magnetic piston DIN ISO 15552 Technical data for series SL 050 450 Order code SL-032-0250-050 Series Piston-Ø Stroke length (mm) Type of cylinder
More informationPage Product family Series Microcylinders 8 mm according to ISO 64 standard M mm according to ISO 6431 / VDMA 24562 standard K KD - 19 High-Tech Rotating pneumatic cylinders 1 mm R - Compact cylinders
More informationLinear/swivel clamp CLR
Key features Functional description The linear/swivel clamp CLR is used for all types of clamping. Through the combination of the linear and swivel motion of the piston rod, it is possible to insert and
More informationOptions selector for T, VT, and ET V T S R 3 / 8 R C E N 1-1/8 5. 5/16" or 3/8"
Series T, T & VT Tiny Tim TUTORS /" and -/8" bore Single and double rod end styles Viton seals optional for higher temperatures Technical data Medium: ompressed air, filtered, lubricated or non-lubricated
More informationClimax Pneumatics. Cnomo NFE Cylinders Easley, South Carolina
Climax Pneumatics Cnomo NFE 49001 Cylinders 1-800-732-8704 Easley, South Carolina End Caps Tube Tie Rods Seals Piston Rod Diecast Aluminum Anodized Aluminum Zinc Coated or Stainless Steel Polyurethane
More information