INSTALLATION, START-UP AND SERVICE INSTRUCTIONS

Transcription

1 INSTALLATION, START-UP AND SERVICE INSTRUCTIONS P705 Refrigeration Condensing Units CONTENTS Page SAFETY CONSIDERATIONS INTRODUCTION HANDLING INSTALLATION Step 1 Complete Pre-Installation Checks Step 2 Select Location Step 3 Wiring Unit Step 4 Piping Step 5 Suction Line Sizing Step 6 Liquid Line Sizing Step 7 Leak Testing and Evacuation START-UP Prepare the System Refrigerant SERVICE Inspection Cleaning s Adding Oil Semi-Hermetic Compressor Hermetic and Scroll Compressor Napthenic Mineral Oils Polyolester Lubricants Alkyl Benzenes SAFETY CONSIDERATIONS Installing, starting up, and servicing refrigeration equipment can be hazardous due to system pressures, electrical components and equipment location (roofs, elevated structures, etc.). Only trained, qualified installers and service mechanics should install, start up, and service this equipment. Untrained personnel can perform basic maintenance functions such as cleaning coils. All other operations should be performed by trained service personnel. When working on the equipment, observe precautions in the literature and on tags, stickers, and labels attached to the equipment. Follow all safety codes. Wear safety glasses and work gloves. Keep quenching cloth and fire extinguisher nearby when brazing. Use care in handling, rigging, and setting bulky equipment. Before installation, always check to be sure main power to systems are OFF. al shock can cause personal injury or death. INTRODUCTION These instructions describe installation, start-up, and service for Totaline P705 refrigeration indoor, outdoor, remote and water-cooled condensing units. HANDLING Fork Lift The compressor side of the condenser unit is the heaviest side and should be facing the lift truck. Be sure the forks extend the entire length of the unit. Crane The center of gravity must be identified before lifting the unit. Holes are provided to insert bars or hooks for lifting unit. To protect the casing, condenser coil, electrical box, piping and wiring, use spreader bars. INSTALLATION Step 1 Complete Pre-Installation Checks Check unit for damage incurred during shipment. File a claim immediately with transit company if damage is found. Verify that the nameplate electrical requirements match the available power supply. Check the shipment for completeness. Step 2 Select Location OUTDOOR CONDENSING UNITS These units are installed outside on a rooftop or on the ground. Be sure to check the load capacity of roof before installing on rooftop. When selecting the location be sure to provide enough space for adequate air circulation and avoid air recirculation. Locate the unit near the power supply and evaporator. Allow accessibility to the unit for maintenance. If more than one unit is installed or if installing a unit close to a wall, a spacing distance of 4 ft is required. See Fig. 1-5 for unit dimensions. To avoid high condensing pressure, the condenser coil must face local prevailing winds or be protected from the wind. Units should be attached to a steel frame (field supplied) on the roof. The frame must be straight and level for proper unit operation. The unit should be securely bolted to the frame. INDOOR CONDENSING UNIT Adequate supply of outside air must be available. Proper ventilation must be provided to vent room air exhaust outside to avoid heat buildup. Room temperature should be maintained at a minimum of 70 F. Provide enough space for adequate air circulation and avoid air recirculation. Allow accessibility to the unit for maintenance. Step 3 Wiring Unit All system wiring must be in compliance with all applicable local and national codes. Internal wiring of fan motors, optional controls and contactors has been completed at factory. Wiring connections terminate on a single terminal block in the control panel and are clearly labeled on the unit. See Fig. 6 for typical wiring. Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. REPLACENT COMPONENTS DIVISION LITERATURE NUMBER P705-2SI CARRIER CORPORATION CATALOG NUMBER PRINTED IN U.S.A. REPLACES P705-1SI

2 REFRIGERANT RECEIVER DIMENSIONS (in.) UNIT (INTERNAL) CHARGE (lb) P705-OCH, OCZ, OCS Size (in.) A B C D E (Dia x Length) R-22 R-404A/R / x / x / x / x / / 8 x / / 4 x NOTE: Dimensions are inches. Fig. 1 P705-OCH, OCZ, OCS Outdoor Air-Cooled Condensing Units, Sizes REFRIGERANT RECEIVER FAN DIMENSIONS (in.) CHARGE (lb) UNIT (INTERNAL) ARRANGE- P705-OCS MENT Size (in.) L W A B R-22 R-404A/R-507 (Dia x Length) x / 4 x x / 4 x x (2) 10 3 /4 x 36 (2) 106 (2) x (2) 10 3 / 4 x 48 (2) 144 (2) 128 NOTE: Dimensions are inches. Fig. 2 P705-OCS Outdoor Air-Cooled Condensing Units, Sizes

3 P705-ICS WITH A CARLYLE SI-HERMETIC P705-ICS WITH A COPELAND SI-HERMETIC REFRIGERANT RECEIVER DIMENSIONS (in.) UNIT (INTERNAL) CHARGE (lb) P705-ICH, ICZ, ICS A B C D E Size (in.) (Dia x Length) R-22 R-404A/R / x / x / x / x / /8 x / / 4 x / / 4 x NOTE: Dimensions are inches. Fig. 3 P705-ICH, ICZ, ICS Indoor Air-Cooled Condensing Units, Sizes

4 UNIT P705-SCS DIMENSIONS (in.) L1 L2 H A Inlet Outlet REFRIGERANT RECEIVER (INTERNAL) Size (in.) (Dia x Length) / /2 1 /2 6 x / / / 8 7 / / 8 x / / / / / 8 x / / /8 1 1 / /4 x / / / / / 4 x NOTES: 1. Dim. L1 for standard unit. Dim. L2 is for unit with optional oil separator and/or suction accumulator. 2. Supplied on low temperature unit only. Fig. 4 P705-SCS Remote Condensing Units, Sizes CHARGE (lb) R-22 R-404A/R-507 REFRIGERANT RECEIVER DIMENSIONS (in.) UNIT (INTERNAL) CHARGE (lb) P705-WCS, MCS Size (in.) L1 L2 H A Inlet Outlet (Dia x Length) R-22 R-404A/R / /2 1 /2 6 x / / / 8 7 / / 8 x / / / / / 8 x / / /8 1 1 / /4 x / / / / / 4 x NOTES: 1. Dim. L1 for standard unit. Dim. L2 is for unit with optional oil separator and/or suction accumulator. 2. Supplied on low temperature unit only. Fig. 5 P705-WCS, MCS Water-Cooled Condensing Units, Sizes

5 /3/60 #C Contactor C Compressor CH Crankcase Heater CT Control Transformer D Oil Failure Delay F Fuse HP High-Pressure Control HSV Hot Gas Bypass Solenoid Valve LP Low Pressure Control M OFS Oil Failure Switch OSH Oil Separator Heater P Internal Protector PDS Pump Down Switch RC Run Capacitor RH Receiver Heater RT Room Thermostat SV Solenoid Valve T Terminal Block 1 Line Number By Others 480/3/60 Fig. 6 Typical Wiring 5

6 The unit must be grounded. A non-fused disconnect switch is provided at the unit. All units are wired for continuous pumpdown cycle. This prevents refrigeration migration from the evaporator to the compressor during a long off cycle with low ambient temperature at the compressor. The liquid line solenoid and thermostat must be wired properly. See Tables 1-16 for specific unit electrical data. Step 4 Piping All refrigerant system components must be installed in accordance with applicable local and national codes using proper engineering practices. Use top quality refrigeration tubing that is internally free of dirt, humidity or other contaminants. Unsealed tubing should not be used. Long radius elbows are recommended. Dry nitrogen must be swept through the lines while joints are brazed to avoid oxidation and carbon deposits. All piping should be properly supported for proper operation. See Fig. 7 and 8. IMPORTANT: The use of a calibrated pressure gage and regulator must always be used with nitrogen gas cylinders. Step 5 Suction Line Sizing (Tables 17-20) The suction line must be sized to maintain proper line velocities with a practical line pressure drop which is usually equal to 2 F. To ensure proper oil return, all horizontal lines must be sloped down toward the compressor with a pitch of 1 /4 in. per 10 ft. The horizontal line can be increased one size in the case of a very long run. In situations where it is necessary for the suction line to rise, an oil trap must be installed at the bottom of the riser. To ensure oil return through a riser in the suction line, a velocity of not less than 1000 ft per minute is required. A trap should be provided for each additional 20 ft of riser. See Fig. 9 and 10. Suction line should not be exposed to heat or the sun. If it is necessary to run suction line outside of the building or through heated areas in the building, the line must be insulated. The suction line must be insulated in any situation where the line may sweat. Step 6 Liquid Line Sizing (Tables 19 and 20) Excessive pressure drop in the liquid line must be avoided to keep a solid column of liquid at the thermostatic expansion valve (TXV). The liquid line solenoid valve should be installed in the liquid line just ahead of the TXV. Sweating of the liquid line may occur in warm ambient due to the subcooled condition of the liquid in winter operation. Step 7 Leak Testing and Evacuation Leak testing and evacuation must be done in accordance with national and local codes. Once all refrigerant connections are made, leak test all joints before charging the system with refrigerant. After leak testing, all moisture and noncondensable gas must be evacuated from the system. Attach a high vacuum line pump and gage on both high and low pressure sides of the system. Be sure all valves such as compressor, hot gas, receiver, and liquid line solenoid valves are open. Break the vacuum in the system with the refrigerant to be used. Always charge the refrigerant into the system through a new 16 cu. in. drier (fieldsupplied) in the charging manifold line. START-UP Units designed for HFC Refrigerant are supplied with polyolester (POE) oil. The oil needs to be added to the system before start-up. The required amount is listed on the unit. This oil is very hygroscopic and care should be taken when using POE. All oil must be used at once. Any remaining oil must be properly disposed of. Prepare the System 1. Add oil to system. 2. Open all refrigeration valves. 3. Connect the high side gage to the refrigerant receiver outlet valve and the suction gage to the suction fitting on the compressor. Refrigerant Add liquid refrigerant to the high side until the system pressure equals the refrigerant cylinder pressure. See Table 21 for refrigerant operating weight. R-22 REFRIGERANT Start the compressor and add refrigerant vapor through the suction connection of the compressor until the sight glass is clear. For outdoor units with flooding valve, restrict the condenser airflow to maintain 100 to 110 F condensing and add enough refrigerant to flood the condenser coil in low ambient. R-404A, R507 (or Blend) REFRIGERANT Start the compressor and add liquid refrigerant through a calibrated restrictor in the suction connection of the compressor until the sight glass is clear. SERVICE System operating temperature, oil level, and system pressure should be checked and recorded periodically to ensure stable system operation. Refer to Table 22 for troubleshooting common condensing unit systems problems. IMPORTANT: Disconnect all power before servicing. Inspection After one day of operation, check for any vibration in the unit. IMPORTANT: Compressor holddown bolts should be checked periodically and re-tightened if necessary. Cleaning It is recommended that the unit be checked periodically for dirt accumulation. Grease and dust should be removed from the fan, fan guards and drain pan. Occasional cleaning of finned surfaces can be done by first dusting the fins then cleaning with a mild detergent and warm water spray. The inner face of the coil may be cleaned by the access panel on the side of the units or by removing the fan guards. IMPORTANT: Do not use alkaline or acidic solution as it will damage the coils. Remove the fan guard to clean the inner face of the fan coil. s Fan motors are permanently lubricated for service free operation. The fan motor may restart on automatic thermal protection if the coil is frozen. The fan motor may cycle if the coil is blocked. If motor is inoperable, check the supply voltage at the motor leads. 6

7 Fig. 7 Pipe Support Example Fig. 8 Supporting Condensing Unit and Compressor to Wall Fig. 9 Suction P-Traps Fig. 10 Double Suction Riser Construction 7

8 UNIT P705-OCS, ICS Table 1 al Data Semi-Hermetic Condensing Units Carlyle Compressors P705-OCS Outdoor Air-Cooled (Sizes ); P705-ICS Indoor Air-Cooled (Sizes ) R-22, R-404A and R-507 Medium Temperature OUT Carlyle Qty Hp 030-2M2-2 06DM /1/ /1/60 1 1/ M2-5 06DM /3/ /1/ / M2-8 06DM /3/ /1/ / M2-9 06DM /3/ /1/60 1 1/ M4-2 06DM /1/ /1/60 1 1/ M4-5 06DM /3/ /1/ / M4-8 06DM /3/ /1/ / M4-9 06DM /3/ /1/60 1 1/ M2-2 06DM /1/ /1/60 1 1/ M2-5 06DM /3/ /1/ / M2-8 06DM /3/ /1/ / M2-9 06DM /3/ /1/60 1 1/ M4-2 06DM /1/ /1/60 1 1/ M4-5 06DM /3/ /1/ / M4-8 06DM /3/ /1/ / M4-9 06DM /3/ /1/60 1 1/ M2-5 06DM /3/ /1/60 1 1/ M2-8 06DM /3/ /1/ / M2-9 06DM /3/ /1/ / M4-5 06DM /3/ /1/60 1 1/ M4-8 06DM /3/ /1/60 1 1/ M4-9 06DM /3/ /1/ / M2-5 06DA /3/ /1/ / M2-8 06DA /3/ /1/60 1 1/ M2-9 06DA /3/ /1/60 1 1/ M2-5 06DR /3/ /1/ / M2-8 06DR /3/ /1/ / M2-9 06DR /3/ /1/60 2 1/ M4-5 06DR /3/ /1/60 2 1/ M4-8 06DR /3/ /1/ / M4-9 06DR /3/ /1/ / M2-5 06DR /3/ /1/60 2 1/ M2-8 06DR /3/ /1/60 2 1/ M2-9 06DR /3/ /1/ / M4-5 06DR /3/ /1/ / M4-8 06DR /3/ /1/60 2 1/ M4-9 06DR /3/ /1/60 2 1/ M2-5 06DR /3/ /1/ / M2-8 06DR /3/ /1/ / M2-9 06DR /3/ /1/ / M4-5 06DR /3/ /1/ / M4-8 06DR /3/ /1/ / M4-9 06DR /3/ /1/ / M2-5 06DM /3/ /1/60 3 1/ M2-8 06DM /3/ /1/ / M2-9 06DM /3/ /1/ / M4-5 06DM /3/ /1/ / M4-8 06DM /3/ /1/60 3 1/ M4-9 06DM /3/ /1/ / M /3/ /1/ / M /3/ /1/ / M /3/ /1/60 3 1/ M /3/ /1/ / M /3/ /1/ / M /3/ /1/ /

9 UNIT P705-OCS, ICS Table 1 al Data Semi-Hermetic Condensing Units Carlyle Compressors P705-OCS Outdoor Air-Cooled (Sizes ); P705-ICS Indoor Air-Cooled (Sizes ) R-22, R-404A and R-507 Medium Temperature (cont) Carlyle Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s Qty Hp OUT 250-2M2-5 06EA /230/3/ /230/3/ M2-8 06EA /3/ /3/ M2-9 06EA /3/ /3/ M4-5 06EA /3/ /3/ M4-8 06EA /3/ /3/ M4-9 06EA /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M2-8 06EA /3/ /3/ M2-9 06EA /3/ /3/ M4-8 06EA /3/ /3/ M4-9 06EA /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ M /3/ /3/ *Condensing units have factory-installed contactors that meet the listed electrical characteristics. P705-OCS only. 9

10 UNIT P705-OCS, ICS Table 2 al Data Semi-Hermetic Condensing Untis Carlyle Compressors P705-OCS Outdoor Air-Cooled (Sizes ); P705-ICS Indoor Air-Cooled (Sizes ) R-22, R-404A and R-507 Low Temperature OUT Carlyle Qty Hp 020-2L2-2 06DR /1/ /1/60 1 1/ L2-5 06DR /3/ /1/ / L2-8 06DR /3/ /1/ / L2-9 06DR /3/ /1/60 1 1/ L4-2 06DR /1/ /1/60 1 1/ L4-5 06DR /3/ /1/ / L4-8 06DR /3/ /1/ / L4-9 06DR /3/ /1/60 1 1/ L2-2 06DR /1/ /1/60 1 1/ L2-5 06DR /3/ /1/ / L2-8 06DR /3/ /1/ / L2-9 06DR /3/ /1/60 1 1/ L4-2 06DR /1/ /1/60 1 1/ L4-5 06DR /3/ /1/ / L4-8 06DR /3/ /1/ / L4-9 06DR /3/ /1/60 1 1/ L2-2 06DR /1/ /1/60 1 1/ L2-5 06DR /3/ /1/ / L2-8 06DR /3/ /1/ / L2-9 06DR /3/ /1/60 1 1/ L4-2 06DR /1/ /1/60 1 1/ L4-5 06DR /3/ /1/ / L4-8 06DR /3/ /1/ / L4-9 06DR /3/ /1/60 1 1/ L2-2 06DR /1/ /1/60 1 1/ L2-5 06DR /3/ /1/ / L2-8 06DR /3/ /1/ / L2-9 06DR /3/ /1/60 1 1/ L4-2 06DR /1/ /1/60 1 1/ L4-5 06DR /3/ /1/ / L4-8 06DR /3/ /1/ / L4-9 06DR /3/ /1/60 1 1/ L2-5 06DR /3/ /1/60 1 1/ L2-8 06DR /3/ /1/ / L2-9 06DR /3/ /1/ / L4-5 06DR /3/ /1/60 1 1/ L4-8 06DR /3/ /1/60 1 1/ L4-9 06DR /3/ /1/ / L2-5 06DR /3/ /1/ / L2-8 06DR /3/ /1/60 1 1/ L2-9 06DR /3/ /1/ / L4-5 06DR /3/ /1/ / L4-8 06DR /3/ /1/ / L4-9 06DR /3/ /1/60 1 1/ L2-5 06DR /3/ /1/ / L2-8 06DR /3/ /1/ / L2-9 06DR /3/ /1/ / L4-5 06DR /3/ /1/60 2 1/ L4-8 06DR /3/ /1/ / L4-9 06DR /3/ /1/ / L2-5 06DR /3/ /1/ / L2-8 06DR /3/ /1/60 2 1/ L2-9 06DR /3/ /1/ / L4-5 06DR /3/ /1/ / L4-8 06DR /3/ /1/ / L4-9 06DR /3/ /1/60 2 1/

11 UNIT P705-OCS, ICS Table 2 al Data Semi-Hermetic Condensing Units Carlyle Compressors P705-OCS Outdoor Air-Cooled (Sizes ); P705-ICS Indoor Air-Cooled (Sizes ) R-22, R-404A and R-507 Low Temperature (cont) Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s OUT Carlyle Qty Hp 150-2L2-5 06ER /3/ /1/60 3 1/ L2-8 06ER /3/ /1/ / L2-9 06ER /3/ /1/ / L4-5 06ER /3/ /1/60 3 1/ L4-8 06ER /3/ /1/60 3 1/ L4-9 06ER /3/ /1/ / L2-5 06ER /3/ /1/ / L2-8 06ER /3/ /1/60 3 1/ L2-9 06ER /3/ /1/60 3 1/ L4-5 06ER /3/ /1/ / L4-8 06ER /3/ /1/ / L4-9 06ER /3/ /1/60 3 1/ L2-5 06ER /3/ /3/ L2-8 06ER /3/ /3/ L2-9 06ER /3/ /3/ L4-5 06ER /3/ /3/ L4-8 06ER /3/ /3/ L4-9 06ER /3/ /3/ L2-5 06ER /3/ /3/ L2-8 06ER /3/ /3/ L2-9 06ER /3/ /3/ L4-5 06ER /3/ /3/ L4-8 06ER /3/ /3/ L4-9 06ER /3/ /3/ L2-5 06ER /3/ /3/ L2-8 06ER /3/ /3/ L2-9 06ER /3/ /3/ L4-5 06ER /3/ /3/ L4-8 06ER /3/ /3/ L4-9 06ER /3/ /3/ L2-5 06ER /3/ /3/ L2-8 06ER /3/ /3/ L2-9 06ER /3/ /3/ L4-5 06ER /3/ /3/ L4-8 06ER /3/ /3/ L4-9 06ER /3/ /3/ L2-5 06ER /3/ /3/ L2-8 06ER /3/ /3/ L2-9 06ER /3/ /3/ L4-5 06ER /3/ /3/ L4-8 06ER /3/ /3/ L4-9 06ER /3/ /3/ *Condensing units have factory-installed contactors that meet the listed electrical characteristics. P705-OCS only. 11

12 Table 3 al Data Semi-Hermetic Condensing Units Carlyle 2-Stage Compressors P705-OCS Outdoor Air-Cooled (Sizes ); P705-ICS Indoor Air-Cooled (Sizes ) R-22 UNIT P705-OCS, ICS Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s OUT Carlyle Qty Hp 040-2T2-5 06CC /3/ /1/ / T2-8 06CC /3/ /1/ / T2-9 06CC /3/ /1/ / T2-5 06CC /3/ /1/ / T2-8 06CC /3/ /1/ / T2-9 06CC /3/ /1/ / T2-5 06CC /3/ /1/ / T2-8 06CC /3/ /1/ / T2-9 06CC /3/ /1/ / T2-5 06CC /3/ /1/ / T2-8 06CC /3/ /1/ / T2-9 06CC /3/ /1/ / T2-5 06CC /3/ /1/ / T2-8 06CC /3/ /1/ / T2-9 06CC /3/ /1/ / T2-5 06CC /3/ /1/ / T2-8 06CC /3/ /1/ / T2-9 06CC /3/ /1/ / T2-5 06CC /3/ /1/ / T2-8 06CC /3/ /1/ / T2-9 06CC /3/ /1/ / T2-5 06CC /3/ /3/ T2-8 06CC /3/ /3/ T2-9 06CC /3/ /3/ T2-5 06CC /3/ /3/ T2-8 06CC /3/ /3/ T2-9 06CC /3/ /3/ T2-8 06CC /3/ /3/ T2-9 06CC /3/ /3/ T2-8 06CC /3/ /3/ T2-9 06CC /3/ /3/ T2-8 06CC /3/ /3/ T2-9 06CC /3/ /3/ *Condensing units have factory-installed contactors that meet the listed electrical characteristics. P705-OCS only. 12

13 UNIT P705-WCS, MCS, SCS Table 4 al Data Water-Cooled/Remote Condensing Units Carlyle Compressors P705-WCS Water-Cooled (Sizes ); P705-MCS Sea Water-Cooled (Sizes ); P705-SCS Remote Compressor (Sizes ) R-22, R-404A and R-507 Medium Temperature Carlyle Qty Hp OUT 030-2M2-2 06DM /1/ NA M2-5 06DM /3/ NA M2-8 06DM /3/ NA M2-9 06DM /3/ NA M4-2 06DM /1/ NA M4-5 06DM /3/ NA M4-8 06DM /3/ NA M4-9 06DM /3/ NA M2-2 06DM /1/ NA M2-5 06DM /3/ NA M2-8 06DM /3/ NA M2-9 06DM /3/ NA M4-2 06DM /1/ NA M4-5 06DM /3/ NA M4-8 06DM /3/ NA M4-9 06DM /3/ NA M2-5 06DM /3/ NA M2-8 06DM /3/ NA M2-9 06DM /3/ NA M4-5 06DM /3/ NA M4-8 06DM /3/ NA M4-9 06DM /3/ NA M2-5 06DA /3/ NA M2-8 06DA /3/ NA M2-9 06DA /3/ NA M2-5 06DR /3/ NA M2-8 06DR /3/ NA M2-9 06DR /3/ NA M4-5 06DR /3/ NA M4-8 06DR /3/ NA M4-9 06DR /3/ NA M2-5 06DR /3/ NA M2-8 06DR /3/ NA M2-9 06DR /3/ NA M4-5 06DR /3/ NA M4-8 06DR /3/ NA M4-9 06DR /3/ NA M2-5 06DR /3/ NA M2-8 06DR /3/ NA M2-9 06DR /3/ NA M4-5 06DR /3/ NA M4-8 06DR /3/ NA M4-9 06DR /3/ NA M2-5 06DM /3/ NA M2-8 06DM /3/ NA M2-9 06DM /3/ NA M4-5 06DM /3/ NA M4-8 06DM /3/ NA M4-9 06DM /3/ NA M /3/ NA M /3/ NA M /3/ NA M /3/ NA M /3/ NA M /3/ NA

14 UNIT P705-WCS, MCS, SCS Table 4 al Data Water-Cooled/Remote Condensing Units Carlyle Compressors P705-WCS Water-Cooled (Sizes ); P705-MCS Sea Water-Cooled (Sizes ); P705-SCS Remote Compressor (Sizes ) R-22, R-404A and R-507 Medium Temperature (cont) Carlyle Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s Qty Hp OUT 250-2M2-5 06EA /3/ NA M2-8 06EA /3/ NA M2-9 06EA /3/ NA M4-5 06EA /3/ NA M4-8 06EA /3/ NA M4-9 06EA /3/ NA M /3/ NA M /3/ NA M /3/ NA M /3/ NA M /3/ NA M /3/ NA M /3/ NA M /3/ NA M /3/ NA M /3/ NA M /3/ NA M /3/ NA *Condensing units have factory-installed contactors that meet the listed electrical characteristics. 14

15 UNIT P705-WCS, MCS, SCS Table 5 al Data Water-Cooled/Remote Condensing Units Carlyle Compressors P705-WCS Water-Cooled (Sizes ); P705-MCS Sea Water-Cooled (Sizes ); P705-SCS Remote Compressor (Sizes ) R-22, R-404A and R-507 Low Temperature Carlyle Qty Hp OUT 020-2L2-2 06DR /1/ NA L2-5 06DR /3/ NA L2-8 06DR /3/ NA L2-9 06DR /3/ NA L4-2 06DR /1/ NA L4-5 06DR /3/ NA L4-8 06DR /3/ NA L4-9 06DR /3/ NA L2-2 06DR /1/ NA L2-5 06DR /3/ NA L2-8 06DR /3/ NA L2-9 06DR /3/ NA L4-2 06DR /1/ NA L4-5 06DR /3/ NA L4-8 06DR /3/ NA L4-9 06DR /3/ NA L2-2 06DR /1/ NA L2-5 06DR /3/ NA L2-8 06DR /3/ NA L2-9 06DR /3/ NA L4-2 06DR /1/ NA L4-5 06DR /3/ NA L4-8 06DR /3/ NA L4-9 06DR /3/ NA L2-2 06DR /1/ NA L2-5 06DR /3/ NA L2-8 06DR /3/ NA L2-9 06DR /3/ NA L4-2 06DR /1/ NA L4-5 06DR /3/ NA L4-8 06DR /3/ NA L4-9 06DR /3/ NA L2-5 06DR /3/ NA L2-8 06DR /3/ NA L2-9 06DR /3/ NA L4-5 06DR /3/ NA L4-8 06DR /3/ NA L4-9 06DR /3/ NA L2-5 06DR /3/ NA L2-8 06DR /3/ NA L2-9 06DR /3/ NA L4-5 06DR /3/ NA L4-8 06DR /3/ NA L4-9 06DR /3/ NA L2-5 06DR /3/ NA L2-8 06DR /3/ NA L2-9 06DR /3/ NA L4-5 06DR /3/ NA L4-8 06DR /3/ NA L4-9 06DR /3/ NA L2-5 06DR /3/ NA L2-8 06DR /3/ NA L2-9 06DR /3/ NA L4-5 06DR /3/ NA L4-8 06DR /3/ NA L4-9 06DR /3/ NA

16 UNIT P705-WCS, MCS, SCS Table 5 al Data Water-Cooled/Remote Condensing Units Carlyle Compressors P705-WCS Water-Cooled (Sizes ); P705-MCS Sea Water-Cooled (Sizes ); P705-SCS Remote Compressor (Sizes ) R-22, R-404A and R-507 Low Temperature (cont) Carlyle Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s Qty Hp OUT 150-2L2-5 06ER /3/ NA L2-8 06ER /3/ NA L2-9 06ER /3/ NA L4-5 06ER /3/ NA L4-8 06ER /3/ NA L4-9 06ER /3/ NA L2-5 06ER /3/ NA L2-8 06ER /3/ NA L2-9 06ER /3/ NA L4-5 06ER /3/ NA L4-8 06ER /3/ NA L4-9 06ER /3/ NA L2-5 06ER /3/ NA L2-8 06ER /3/ NA L2-9 06ER /3/ NA L4-5 06ER /3/ NA L4-8 06ER /3/ NA L4-9 06ER /3/ NA L2-5 06ER /3/ NA L2-8 06ER /3/ NA L2-9 06ER /3/ NA L4-5 06ER /3/ NA L4-8 06ER /3/ NA L4-9 06ER /3/ NA *Condensing units have factory-installed contactors that meet the listed electrical characteristics. 16

17 Table 6 al Data Water-Cooled/Remote Condensing Units Carlyle 2-Stage Compressors P705-WCS Water-Cooled (Sizes ); P705-MCS Sea Water-Cooled (Sizes ); P705-SCS Remote Compressor (Sizes ) R-22 Low Temperature UNIT P705-WCS, MCS, SCS Carlyle Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s Qty Hp OUT 040-2T2-5 06CC /3/ NA T2-8 06CC /3/ NA T2-9 06CC /3/ NA T2-5 06CC /3/ NA T2-8 06CC /3/ NA T2-9 06CC /3/ NA T2-5 06CC /3/ NA T2-8 06CC /3/ NA T2-9 06CC /3/ NA T2-5 06CC /3/ NA T2-8 06CC /3/ NA T2-9 06CC /3/ NA T2-5 06CC /3/ NA T2-8 06CC /3/ NA T2-9 06CC /3/ NA T2-5 06CC /3/ NA T2-8 06CC /3/ NA T2-9 06CC /3/ NA T2-5 06CC /3/ NA T2-8 06CC /3/ NA T2-9 06CC /3/ NA T2-5 06CC /3/ NA T2-8 06CC /3/ NA T2-9 06CC /3/ NA T2-5 06CC /3/ NA T2-8 06CC /3/ NA T2-9 06CC /3/ NA *Condensing units have factory-installed contactors that meet the listed electrical characteristics. 17

18 UNIT P705-OCS, ICS Table 7 al Data Semi-Hermetic Condensing Units Copeland Compressors P705-OCS Outdoor Air-Cooled (Sizes ); P705-ICS Indoor Air-Cooled (Sizes ) R-22, R-404A and R-507 High and Medium Temperature OUT Copeland Qty Hp 008-1H2-2 KAN CAV 240/1/ /1/60 1 1/ H2-5 KAN TAC /3/ /1/ / H2-2 KAR CAV 240/1/ /1/ / H2-5 KAR TAC /3/ /1/60 1 1/ M4-2 KARB-010E-CAV 240/1/ /1/60 1 1/ M4-5 KARA-010E-TAC /3/ /1/ / H2-2 KAGB-0150-CAV 240/1/ /1/ / H2-5 KAGA-0150-TAC /3/ /1/60 1 1/ M4-2 KAKB-021E-CAV 240/1/ /1/60 1 1/ M4-5 KAKA-020E-TAC /3/ /1/ / H2-2 KAKB-0200-CAV 240/1/ /1/ / H2-5 KAKA-0200-TAC /3/ /1/60 1 1/ H2-8 ERA TAE 600/3/ /1/60 1 1/ H2-9 KAKA-0200-TAD 480/3/ /1/ / M4-5 ERCA-021E-TAC /3/ /1/ / M4-8 ERCA-020E-TAE 600/3/ /1/60 1 1/ H2-2 ERF CAB 240/1/ /1/60 1 1/ H2-5 ERF TAC /3/ /1/ / H2-8 ERF TAE 600/3/ /1/ / H2-9 ERF TAD 480/3/ /1/60 1 1/ M4-5 ERFA-031E-TAC /3/ /1/60 1 1/ M4-8 ERFA-031E-TAE 600/3/ /1/ / M4-9 ERFA-031E-TAD 480/3/ /1/ / H2-2 NRB CFB 240/1/ /1/60 1 1/ H2-5 NRB TFC /3/ /1/60 1 1/ H2-8 NRB TFE 600/3/ /1/ / H2-9 NRB TFD 480/3/ /1/ / H2-5 NRA TFC /3/ /1/60 1 1/ H2-8 NRA TFE 600/3/ /1/60 1 1/ H2-9 NRA TFD 480/3/ /1/ / M4-5 2DC3-050E-TFC /3/ /1/ / M4-8 2DC3-050E-TFE 600/3/ /1/60 1 1/ M4-9 2DC3-050E-TFD 480/3/ /1/60 1 1/ H2-5 2DD TFC /3/ /1/ / H2-8 2DD TFE 600/3/ /1/ / H2-9 2DD TFD 480/3/ /1/60 1 1/ M4-5 2DD3-050E-TFC /3/ /1/60 1 1/ M4-8 2DD3-050E-TFE 600/3/ /1/ / M4-9 2DD3-050E-TFD 480/3/ /1/ / H2-5 2DL TFC /3/ /1/60 1 1/ H2-8 2DL TFE 600/3/ /1/ / H2-9 2DL TFD 480/3/ /1/ / M4-5 2DL3-075E-TFC /3/ /1/ / M4-8 2DL3-075E-TFE 600/3/ /1/60 1 1/ M4-9 2DL3-075E-TFD 480/3/ /1/ / H2-5 2DA TFC /3/ /1/ / H2-8 2DA TFE 600/3/ /1/ / H2-9 2DA TFD 480/3/ /1/60 2 1/ M4-5 2DA3-075E-TFC /3/ /1/ / M4-8 2DA3-075E-TFE 600/3/ /1/ / M4-9 2DA3-075E-TFD 480/3/ /1/ / H2-5 3DA3A-0750-TFC /3/ /1/60 2 1/ H2-8 3DA3A-0750-TFE 600/3/ /1/ / H2-9 3DA3A-0750-TFD 480/3/ /1/ / M4-5 3DA3A-075E-TFC /3/ /1/ / M4-8 3DA3A-075E-TFE 600/3/ /1/60 2 1/ M4-9 3DA3A-075E-TFD 480/3/ /1/ /

19 UNIT P705-OCS, ICS Table 7 al Data Semi-Hermetic Condensing Units Copeland Compressors P705-OCS Outdoor Air-Cooled (Sizes ); P705-ICS Indoor Air-Cooled (Sizes ) R-22, R-404A and R-507 High and Medium Temperature (cont) Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s OUT Copeland Qty Hp 100-1H2-5 3DB3A-1000-TFC /3/ /1/60 2 1/ H2-8 3DB3A-1000-TFE 600/3/ /1/ / H2-9 3DB3A-1000-TFD 480/3/ /1/ / M4-5 3DB3A-100E-TFC /3/ /1/60 2 1/ M4-8 3DB3A-100E-TFE 600/3/ /1/60 2 1/ M4-9 3DB3A-100E-TFD 480/3/ /1/ / H2-5 3DS3A-1500-TFC /3/ /1/ / H2-8 3DS3A-1500-TFE 600/3/ /1/60 3 1/ H2-9 3DS3A-1500-TFD 480/3/ /1/60 3 1/ M4-5 3DS3A-150E-TFC /3/ /1/ / M4-8 3DS3A-150E-TFE 600/3/ /1/ / M4-9 3DS3A-150E-TFD 480/3/ /1/60 3 1/ H2-5 4DA TSK /3/ /1/60 3 1/ H2-8 4DA TSE 600/3/ /1/ / H2-9 4DA TSK 480/3/ /1/ / M4-5 4DA3-200E-TSK /3/ /1/60 3 1/ M4-8 4DA3-200E-TSE 600/3/ /1/60 3 1/ M4-9 4DA3-200E-TSK 480/3/ /1/ / H2-5 4DH TSK /3/ /3/ H2-8 4DH TSE 600/3/ /3/ H2-9 4DH TSK 480/3/ /3/ M4-5 4DH3-250E-TSK /3/ /3/ M4-8 4DH3-250E-TSE 600/3/ /3/ M4-9 4DH3-250E-TSK 480/3/ /3/ H2-5 4DJ TSK /3/ /3/ H2-8 4DJ TSE 600/3/ /3/ H2-9 4DJ TSK 480/3/ /3/ M4-5 4DJ3-300E-TSK /3/ /3/ M4-8 4DJ3-300E-TSE 600/3/ /3/ M4-9 4DJ3-300E-TSK 480/3/ /3/ H2-5 6DH TSK /3/ /3/ H2-8 6DH TSE 600/3/ /3/ H2-9 6DH TSK 480/3/ /3/ M4-5 6DH3-350E-TSK /3/ /3/ M4-8 6DH3-350E-TSE 600/3/ /3/ M4-9 6DH3-350E-TSK 480/3/ /3/ H2-8 6DJ TSE 600/3/ /3/ H2-9 6DJ TSN 480/3/ /3/ M4-8 6DJ3-400E-TSE 600/3/ /3/ M4-9 6DJ3-400E-TSN 480/3/ /3/ H2-5 4DH TSK /3/ /3/ H2-8 4DH TSE 600/3/ /3/ H2-9 4DH TSK 480/3/ /3/ M4-5 4DH3-250E-TSK /3/ /3/ M4-8 4DH3-250E-TSE 600/3/ /3/ M4-9 4DH3-250E-TSK 480/3/ /3/ H2-8 4DJ TSE 600/3/ /3/ H2-9 4DJ TSK 480/3/ /3/ M4-8 4DJ3-300E-TSE 600/3/ /3/ M4-9 4DJ3-300E-TSK 480/3/ /3/ *Condensing units have factory-installed contactors that meet the listed electrical characteristics. P705-OCS only. 19

20 UNIT P705-OCS, ICS Table 7 al Data Semi-Hermetic Condensing Units Copeland Compressors P705-OCS Outdoor Air-Cooled (Sizes ); P705-ICS Indoor Air-Cooled (Sizes ) R-22, R-404A and R-507 High and Medium Temperature (cont) Copeland Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s Qty Hp OUT 702-1H2-8 6DH TSE 600/3/ /3/ H2-9 6DH TSK 480/3/ /3/ M4-8 6DH3-350E-TSE 600/3/ /3/ M4-9 6DH3-350E-TSK 480/3/ /3/ H2-8 6DJ TSE 600/3/ /3/ H2-9 6DJ TSN 480/3/ /3/ M4-8 6DJ3-400E-TSE 600/3/ /3/ M4-9 6DJ3-400E-TSN 480/3/ /3/ *Condensing units have factory-installed contactors that meet the listed electrical characteristics. P705-OCS only. 20

21 UNIT P705-OCS, ICS Table 8 al Data Semi-Hermetic Condensing Units Copeland Compressors P705-OCS Outdoor Air-Cooled (Sizes ); P705-ICS Indoor Air-Cooled (Sizes ) R-22, R-404A and R-507 Low Temperature Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s OUT Copeland Qty Hp 008-1L2-2 KAMB-0075-CAV /1/ /1/60 1 1/ L2-5 KAMA-0075-TAC /3/ /1/ / L4-2 KAMB-007E-CAV /1/ /1/ / L4-5 KAMA-007E-TAC /3/ /1/60 1 1/ L2-2 KAJB-0100-CAV /1/ /1/60 1 1/ L2-5 KAJA-0101-TAC /3/ /1/ / L4-2 KAJB-010E-CAV /1/ /1/ / L4-5 KAJA-011E-TAC /3/ /1/60 1 1/ L2-2 KAKB-0200-CAV /1/ /1/60 1 1/ L2-5 KAKA-0200-TAC /3/ /1/ / L4-2 KAKB-011E-CAV /1/ /1/ / L4-2 KALB-015E-CAV /1/ /1/60 1 1/ L4-5 KALA-016E-TAC /3/ /1/60 1 1/ L2-2 EADB-0200-CAB 240/1/ /1/ / L2-5 EADA-0200-TAC /3/ /1/ / L4-2 EADB-021E-CAB 240/1/ /1/60 1 1/ L4-5 EADA-020E-TAC /3/ /1/60 1 1/ L2-2 EAVB-0210-CAV /1/ /1/ / L2-5 EAVA-0210-TAC /3/ /1/ / L2-9 EAVA-0210-TAD 480/3/ /1/60 1 1/ L4-2 EAVB-021E-CAV /1/ /1/60 1 1/ L4-5 EAVA-021E-TAC /3/ /1/ / L4-8 EAVA-021E-TAE 600/3/ /1/ / L4-9 EAVA-021E-TAD 480/3/ /1/60 1 1/ L2-2 LAHB-0311-CAB 240/1/ /1/60 1 1/ L2-5 LAHA-0310-TAC /3/ /1/ / L2-9 LAHA-0310-TAD 480/3/ /1/ / L4-2 LAHB-032E-CAB 240/1/ /1/60 1 1/ L4-5 LAHA-032E-TAC /3/ /1/60 1 1/ L4-8 LAHB-032E-TAE 600/3/ /1/ / L4-9 LAHB-032E-TAD 480/3/ /1/ / L2-2 2DF CFB 240/1/ /1/60 1 1/ L2-5 2DF TFC /3/ /1/60 1 1/ L2-8 2DF TFE 600/3/ /1/ / L2-9 2DF TFD 480/3/ /1/ / L4-2 2DF3-030E-CFB 240/1/ /1/60 1 1/ L4-5 2DF3-030E-TFC /3/ /1/60 1 1/ L4-8 2DF3-030E-TFE 600/3/ /1/ / L4-9 2DF3-030E-TFD 480/3/ /1/ / L2-5 2DL TFC /3/ /1/60 1 1/ L2-8 2DL TFE 600/3/ /1/ / L2-9 2DL TFD 480/3/ /1/ / L4-5 2DL3-040E-TFC /3/ /1/ / L4-8 2DL3-040E-TFE 600/3/ /1/60 1 1/ L4-9 2DL3-040E-TFD 480/3/ /1/ / L2-5 2DA TFC /3/ /1/ / L2-8 2DA TFE 600/3/ /1/ / L2-9 2DA TFD 480/3/ /1/60 1 1/ L4-5 2DA3-060E-TFC /3/ /1/ / L4-8 2DA3-060E-TFE 600/3/ /1/ / L4-9 2DA3-060E-TFD 480/3/ /1/ / *Condensing units have factory-installed contactors that meet the listed electrical characteristics. 21

22 UNIT P705-OCS, ICS Table 8 al Data Semi-Hermetic Condensing Units Copeland Compressors P705-OCS Outdoor Air-Cooled (Sizes ); P705-ICS Indoor Air-Cooled (Sizes ) R-22, R-404A and R-507 Low Temperature (cont) OUT Copeland Qty Hp 070-1L2-5 3DA3A-0600-TFC /3/ /1/60 1 1/ L2-8 3DA3A-0600-TFE 600/3/ /1/ / L2-9 3DA3A-0600-TFD 480/3/ /1/ / L4-5 3DA3A-060E-TFC /3/ /1/60 1 1/ L4-8 3DA3A-060E-TFE 600/3/ /1/60 1 1/ L4-9 3DA3A-060E-TFD 480/3/ /1/ / L2-5 3DB3A-0750-TFC /3/ /1/ / L2-8 3DB3A-0750-TFE 600/3/ /1/60 2 1/ L2-9 3DB3A-0750-TFD 480/3/ /1/60 2 1/ L4-5 3DB3A-075E-TFC /3/ /1/ / L4-8 3DB3A-075E-TFE 600/3/ /1/ / L4-9 3DB3A-075E-TFD 480/3/ /1/60 2 1/ L2-5 3DF3A-0900-TFC /3/ /1/60 2 1/ L2-8 3DF3A-0900-TFE 600/3/ /1/ / L2-9 3DF3A-0900-TFD 480/3/ /1/ / L4-5 3DF3A-090E-TFC /3/ /1/60 2 1/ L4-8 3DF3A-090E-TFE 600/3/ /1/60 2 1/ L4-9 3DF3A-090E-TFD 480/3/ /1/ / L2-5 3DS3A-1000-TFC /3/ /1/ / L2-8 3DS3A-1000-TFE 600/3/ /1/60 2 1/ L2-9 3DS3A-1000-TFD 480/3/ /1/60 2 1/ L4-5 3DS3A-100E-TFC /3/ /1/ / L4-8 3DS3A-100E-TFE 600/3/ /1/ / L4-9 3DS3A-100E-TFD 480/3/ /1/60 2 1/ L2-5 4DL TSK /3/ /1/60 3 1/ L2-8 4DL TSE 600/3/ /1/ / L2-9 4DL TSK 480/3/ /1/ / L4-5 4DL3-150E-TSK /3/ /1/60 3 1/ L4-8 4DL3-150E-TSE 600/3/ /1/60 3 1/ L4-9 4DL3-150E-TSK 480/3/ /1/ / L2-5 4DT TSK /3/ /1/ / L2-8 4DT TSE 600/3/ /1/60 3 1/ L2-9 4DT TSK 480/3/ /1/60 3 1/ L4-5 4DT3-220E-TSK /3/ /1/ / L4-8 4DT3-220E-TSE 600/3/ /1/ / L4-9 4DT3-220E-TSK 480/3/ /1/60 3 1/ L2-5 6DL TSK /3/ /3/ L2-8 6DL TSE 600/3/ /3/ L2-9 6DL TSK 480/3/ /3/ L4-5 6DL3-270E-TSK /3/ /3/ L4-8 6DL3-270E-TSE 600/3/ /3/ L4-9 6DL3-270E-TSK 480/3/ /3/ L2-5 6DT TSK /3/ /3/ L2-8 6DT TSE 600/3/ /3/ L2-9 6DT TSK 480/3/ /3/ L4-5 6DT3-300E-TSK /3/ /3/ L4-8 6DT3-300E-TSE 600/3/ /3/ L4-9 6DT3-300E-TSK 480/3/ /3/ L2-5 4DT TSK /3/ /3/ L2-8 4DT TSE 600/3/ /3/ L2-9 4DT TSK 480/3/ /3/ L4-5 4DT3-220E-TSK /3/ /3/ L4-8 4DT3-220E-TSE 600/3/ /3/ L4-9 4DT3-220E-TSK 480/3/ /3/

23 UNIT P705-OCS, ICS Table 8 al Data Semi-Hermetic Condensing Units Copeland Compressors P705-OCS Outdoor Air-Cooled (Sizes ); P705-ICS Indoor Air-Cooled (Sizes ) R-22, R-404A and R-507 Low Temperature (cont) Copeland Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s Qty Hp OUT 542-1L2-8 6DL TSE 600/3/ /3/ L2-9 6DL TSK 480/3/ /3/ L4-8 6DL3-270E-TSE 600/3/ /3/ L4-9 6DL3-270E-TSK 480/3/ /3/ L2-8 6DT TSE 600/3/ /3/ L2-9 6DT TSK 480/3/ /3/ L4-8 6DT3-300E-TSE 600/3/ /3/ L4-9 6DT3-300E-TSK 480/3/ /3/ *Condensing units have factory-installed contactors that meet the listed electrical characteristics. P705-OCS only. 23

24 UNIT P705-OCH, ICH Table 9 al Data Hermetic Condensing Units Copeland Compressors P705-OCH Outdoor Air-Cooled (Sizes ); P705-ICH Indoor Air-Cooled (Sizes ) R-22, R-404A and R-507 High and Medium Temperature Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s OUT Copeland Qty Hp 007-1M4-2 RS43C2E-CAV /1/ /1/60 1 1/ H2-2 RS47C2-IAV /1/ /1/ / M4-2 RS55C2E-CAV /1/ /1/ / H2-2 RS64C2-CAV /1/ /1/60 1 1/ M4-2 RS70C1E-PFV /1/ /1/60 1 1/ H2-2 RS70C1-PFV /1/ /1/ / H2-5 RS70C1-TFC /3/ /1/ / H2-2 CR18KQ-PFV /1/ /1/60 1 1/ H2-5 CR18KQ-TF /3/ /1/60 1 1/ M4-2 RS97CZE-CAV /1/ /1/ / M4-5 RS97CZE-TFC /3/ /1/ / H2-2 CR24KQ-PFV /1/ /1/60 1 1/ H2-5 CR24KQ-TF /3/ /1/60 1 1/ H2-9 CR24KQ-TFD 480/3/ /1/ / M4-2 CS12K6E-PFV /1/ /1/ / M4-5 CS12K6E-TF /3/ /1/60 1 1/ H2-2 CR33KQ-PFV /1/ /1/60 1 1/ H2-5 CR33KQ-TF /3/ /1/ / H2-9 CR33KQ-TFD 480/3/ /1/ / M4-2 CS14K6E-PFV /1/ /1/60 1 1/ M4-5 CS14K6E-TF /3/ /1/60 1 1/ H2-2 CR37KQ-PFV /1/ /1/ / H2-5 CR37KQ-TF /3/ /1/ / H2-9 CR37KQ-TFD 480/3/ /1/60 1 1/ M4-2 CS18K6E-PFV /1/ /1/60 1 1/ M4-5 CS18K6E-TF /3/ /1/ / H2-2 CR47KQ-PFV /1/ /1/ / H2-5 CR47KQ-TF /3/ /1/60 1 1/ H2-9 CR47KQ-TFD 480/3/ /1/60 1 1/ M4-2 CS20K6E-PFV /1/ /1/ / M4-5 CS20K6E-TF /3/ /1/ / H2-2 CR53KQ-PFV /1/ /1/60 1 1/ H2-5 CR53KQ-TF /3/ /1/60 1 1/ H2-9 CR53KQ-TFD 480/3/ /1/ / M4-2 CS27K6E-PFV /1/ /1/ / M4-5 CS27K6E-TF /3/ /1/60 1 1/ H2-2 CRN PFV /1/ /1/60 1 1/ H2-5 CRN TF /3/ /1/ / H2-8 CRN TFE 600/3/ /1/ / H2-9 CRN TFD 480/3/ /1/60 1 1/ M4-2 CS33K6E-PFV /1/ /1/ / M4-5 CS33K6E-TFS /3/ /1/ / M4-9 CS33K6E-TFD 480/3/ /1/ / *Condensing units have factory-installed contactors that meet the listed electrical characteristics. 24

25 Table 10 al Data Scroll Compressor Condensing Units Copeland Scroll Compressors P705-OCH Outdoor Air-Cooled (Sizes ); P705-ICH Indoor Air-Cooled (Sizes ) R-404A and R-507 Low Temperature UNIT P705-OCH, ICH Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s OUT Copeland Qty Hp 015-1L4-2 CF04K6E-PFV /1/ /1/60 1 1/ L4-5 CF04K6E-TF /3/ /1/ / L4-2 CF06K6E-PFV /1/ /1/ / L4-5 CF06K6E-TF /3/ /1/60 1 1/ L4-2 CF09K6E-PFV /1/ /1/60 1 1/ L4-5 CF09K6E-TF /3/ /1/ / L4-2 CF12K6E-PFV /1/ /1/ / L4-5 CF12K6E-TF /3/ /1/60 1 1/ *Condensing units have factory-installed contactors that meet the listed electrical characteristics. 25

26 Table 11 al Data Scroll Compressor Condensing Units Copeland Scroll Compressors P705-OCZ Outdoor Air-Cooled (Sizes ); P705-ICZ Indoor Air-Cooled (Sizes ) R-22 High Temperature UNIT P705-OCZ, ICZ Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s OUT Copeland Qty Hp 015-1H2-2 ZR18K4-PFV 240/1/ /1/60 1 1/ H2-2 ZR24K4-PFV 240/1/ /1/ / H2-5 ZR24K3-TF /3/ /1/ / H2-9 ZR24K3-TFD 480/3/ /1/60 1 1/ H2-2 ZR30K3-PFV 240/1/ /1/60 1 1/ H2-5 ZR30K3-TF /3/ /1/ / H2-9 ZR30K3-TFD 480/3/ /1/ / H2-2 ZR36K3-PFV 240/1/ /1/60 1 1/ H2-5 ZR36K3-TF /3/ /1/60 1 1/ H2-8 ZR36K3-TFE 600/3/ /1/ / H2-9 ZR36K3-TFD 480/3/ /1/ / H2-2 ZR42K3-PFV 240/1/ /1/60 1 1/ H2-5 ZR42K3-TF /3/ /1/60 1 1/ H2-8 ZR42K3-TFE 600/3/ /1/ / H2-9 ZR42K3-TFD 480/3/ /1/ / H2-2 ZR48K3-PFV 240/1/ /1/60 1 1/ H2-5 ZR48K3-TF /3/ /1/60 1 1/ H2-8 ZR48K3-TFE 600/3/ /1/ / H2-9 ZR48K3-TFD 480/3/ /1/ / H2-2 ZR61K3-PFV 240/1/ /1/60 1 1/ H2-5 ZR61K3-TF /3/ /1/60 1 1/ H2-8 ZR61K3-TFE 600/3/ /1/ / H2-9 ZR61K3-TFD 480/3/ /1/ / H2-5 ZR72KC-TF /3/ /1/60 1 1/ H2-8 ZR72KC-TFE 600/3/ /1/60 1 1/ H2-9 ZR72KC-TFD 480/3/ /1/ / H2-5 ZR84KC-TF /3/ /1/ / H2-8 ZR84KC-TFE 600/3/ /1/60 1 1/ H2-9 ZR84KC-TFD 480/3/ /1/60 1 1/ H2-5 ZR94KC-TF /3/ /1/ / H2-8 ZR94KC-TFE 600/3/ /1/ / H2-9 ZR94KC-TFD 480/3/ /1/60 2 1/ H2-5 ZR108KC-TF /3/ /1/60 2 1/ H2-8 ZR108KC-TFE 600/3/ /1/ / H2-9 ZR108KC-TFD 480/3/ /1/ / H2-5 ZR125KC-TF /3/ /1/60 2 1/ H2-8 ZR125KC-TFE 600/3/ /1/60 2 1/ H2-9 ZR125KC-TFD 480/3/ /1/ / *Condensing units have factory-installed contactors that meet the listed electrical characteristics. 26

27 Table 12 al Data Scroll Compressor Condensing Units Copeland Scroll Compressors P705-OCZ Outdoor Air-Cooled (Sizes ); P705-ICZ Indoor Air-Cooled (Sizes ) R-22 Medium Temperature UNIT P705-OCZ, ICZ Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s OUT Copeland Qty Hp 025-1M2-2 ZB21KC-PFV 240/1/ /1/60 1 1/ M2-5 ZB21KC-TF /3/ /1/ / M2-8 ZB21KC-TFE 600/3/ /1/ / M2-9 ZB21KC-TFD 480/3/ /1/60 1 1/ M2-2 ZB26KC-PFV 240/1/ /1/60 1 1/ M2-5 ZB26KC-TF /3/ /1/ / M2-8 ZB26KC-TFE 600/3/ /1/ / M2-9 ZB26KC-TFD 480/3/ /1/60 1 1/ M2-2 ZB30KC-PFV 240/1/ /1/60 1 1/ M2-5 ZB30KC-TF /3/ /1/ / M2-8 ZB30KC-TFE 600/3/ /1/ / M2-9 ZB30KC-TFD 480/3/ /1/60 1 1/ M2-2 ZB38KC-PFV 240/1/ /1/60 1 1/ M2-5 ZB38KC-TF /3/ /1/ / M2-8 ZB38KC-TFE 600/3/ /1/ / M2-9 ZB38KC-TFD 480/3/ /1/60 1 1/ M2-5 ZB45KC-TF /3/ /1/60 1 1/ M2-8 ZB45KC-TFE 600/3/ /1/ / M2-9 ZB45KC-TFD 480/3/ /1/ / M2-5 ZB56KA-TWC /3/ /1/60 2 1/ M2-8 ZB56KA-TWE 600/3/ /1/60 2 1/ M2-9 ZB56KA-TWD 480/3/ /1/ / M2-5 ZB75KA-TWC /3/ /1/ / M2-8 ZB75KA-TWE 600/3/ /1/60 2 1/ M2-9 ZB75KA-TWD 480/3/ /1/60 2 1/ M2-5 ZB92KA-TWC /3/ /1/ / M2-8 ZB92KA-TWE 600/3/ /1/ / M2-9 ZB92KA-TWD 480/3/ /1/60 2 1/ M2-5 ZB11MA-TWC /3/ /1/60 3 1/ M2-8 ZB11MA-TWE 600/3/ /1/ / M2-9 ZB11MA-TWD 480/3/ /1/ / *Condensing units have factory-installed contactors that meet the listed electrical characteristics. 27

28 Table 13 al Data Scroll Compressor Condensing Units Copeland Scroll Compressors P705-OCZ Outdoor Air-Cooled (Sizes ); P705-ICZ Indoor Air-Cooled (Sizes ) R-404A and R-507 Medium Temperature UNIT P705-OCZ, ICZ Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s OUT Copeland Qty Hp 025-1M4-2 ZS21K4E-PFV 240/1/ /1/60 1 1/ M4-5 ZS21K4E-TF /3/ /1/ / M4-8 ZS21K4E-TFE 600/3/ /1/ / M4-9 ZS21K4E-TFD 480/3/ /1/60 1 1/ M4-2 ZS26K4E-PFV 240/1/ /1/60 1 1/ M4-5 ZS26K4E-TF /3/ /1/ / M4-8 ZS26K4E-TFE 600/3/ /1/ / M4-9 ZS26K4E-TFD 480/3/ /1/60 1 1/ M4-2 ZS30K4E-PFV 240/1/ /1/60 1 1/ M4-5 ZS30K4E-TF /3/ /1/ / M4-8 ZS30K4E-TFE 600/3/ /1/ / M4-9 ZS30K4E-TFD 480/3/ /1/60 1 1/ M4-2 ZS38K4E-PFV 240/1/ /1/60 1 1/ M4-5 ZS38K4E-TF /3/ /1/ / M4-8 ZS38K4E-TFE 600/3/ /1/ / M4-9 ZS38K4E-TFD 480/3/ /1/60 1 1/ M4-5 ZS45K4E-TF /3/ /1/60 1 1/ M4-8 ZS45K4E-TFE 600/3/ /1/ / M4-9 ZS45K4E-TFD 480/3/ /1/ / M4-5 ZS56K4E-TWC /3/ /1/60 1 1/ M4-8 ZS56K4E-TWE 600/3/ /1/60 1 1/ M4-9 ZS56K4E-TWD 480/3/ /1/ / M4-5 ZS75K4E-TWC /3/ /1/ / M4-8 ZS75K4E-TWE 600/3/ /1/60 2 1/ M4-9 ZS75K4E-TWD 480/3/ /1/60 2 1/ *Condensing units have factory-installed contactors that meet the listed electrical characteristics. 28

29 Table 14 al Data Scroll Compressor Condensing Units Copeland Scroll Compressors P705-OCZ Outdoor Air-Cooled (Sizes ); P705-ICZ Indoor Air-Cooled (Sizes ) R-404A and R-507 Low Temperature UNIT P705-OCZ, ICZ Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s OUT Copeland Qty Hp 025-1L4-2 ZF09K4E-PFV 240/1/ /1/60 1 1/ L4-5 ZF09K4E-TF /3/ /1/ / L4-8 ZF09K4E-TFE 600/3/ /1/ / L4-9 ZF09K4E-TFD 480/3/ /1/60 1 1/ L4-2 ZF11K4E-PFV 240/1/ /1/60 1 1/ L4-5 ZF11K4E-TF /3/ /1/ / L4-8 ZF11K4E-TFE 600/3/ /1/ / L4-9 ZF11K4E-TFD 480/3/ /1/60 1 1/ L4-2 ZF13K4E-PFV 240/1/ /1/60 1 1/ L4-5 ZF13K4E-TF /3/ /1/ / L4-8 ZF13K4E-TFE 600/3/ /1/ / L4-9 ZF13K4E-TFD 480/3/ /1/60 1 1/ L4-2 ZF15K4E-PFV 240/1/ /1/60 1 1/ L4-5 ZF15K4E-TF /3/ /1/ / L4-8 ZF15K4E-TFE 600/3/ /1/ / L4-9 ZF15K4E-TFD 480/3/ /1/60 1 1/ L4-5 ZF18K4E-TF /3/ /1/60 1 1/ L4-8 ZF18K4E-TFE 600/3/ /1/ / L4-9 ZF18K4E-TFD 480/3/ /1/ / L4-5 ZF24K4E-TWC /3/ /1/60 1 1/ L4-8 ZF24K4E-TWE 600/3/ /1/60 1 1/ L4-9 ZF24K4E-TWD 480/3/ /1/ / L4-5 ZF33K4E-TWC /3/ /1/ / L4-8 ZF33K4E-TWE 600/3/ /1/60 2 1/ L4-9 ZF33K4E-TWD 480/3/ /1/ / *Condensing units have factory-installed contactors that meet the listed electrical characteristics. 29

30 Table 15 al Data Water-Cooled/Remote Condensing Units Copeland Compressors P705-WCS Water-Cooled (Sizes ); P705-MCS Sea Water-Cooled (Sizes ); P705-SCS Remote Compressor (Sizes ) R-22, R-404A and R-507 High and Medium Temperature UNIT P705-WCS, MCS, SCS Copeland Qty Hp OUT 008-1H2-2 KAN CAV 240/1/ NA H2-5 KAN TAC /3/ NA H2-2 KAR CAV 240/1/ NA H2-5 KAR TAC /3/ NA M4-2 KARB-010E-CAV 240/1/ NA M4-5 KARA-010E-TAC /3/ NA H2-2 KAGB-0150-CAV 240/1/ NA H2-5 KAGA-0150-TAC /3/ NA M4-2 KAKB-021E-CAV 240/1/ NA M4-5 KAKA-020E-TAC /3/ NA H2-2 KAKB-0200-CAV 240/1/ NA H2-5 KAKA-0200-TAC /3/ NA H2-8 ERA TAE 600/3/ NA H2-9 KAKA-0200-TAD 480/3/ NA M4-5 ERCA-021E-TAC /3/ NA M4-8 ERCA-020E-TAE 600/3/ NA H2-2 ERF CAB 240/1/ NA H2-5 ERF TAC /3/ NA H2-8 ERF TAE 600/3/ NA H2-9 ERF TAD 480/3/ NA M4-5 ERFA-031E-TAC /3/ NA M4-8 ERFA-031E-TAE 600/3/ NA M4-9 ERFA-031E-TAD 480/3/ NA H2-2 NRB CFB 240/1/ NA H2-5 NRB TFC /3/ NA H2-8 NRB TFE 600/3/ NA H2-9 NRB TFD 480/3/ NA H2-5 NRA TFC /3/ NA H2-8 NRA TFE 600/3/ NA H2-9 NRA TFD 480/3/ NA M4-2 2DC3-050E-CFB 240/1/ NA M4-5 2DC3-050E-TFC /3/ NA M4-8 2DC3-050E-TFE 600/3/ NA M4-9 2DC3-050E-TFD 480/3/ NA H2-5 2DD TFC /3/ NA H2-8 2DD TFE 600/3/ NA H2-9 2DD TFD 480/3/ NA M4-5 2DD3-050E-TFC /3/ NA M4-8 2DD3-050E-TFE 600/3/ NA M4-9 2DD3-050E-TFD 480/3/ NA H2-5 2DL TFC /3/ NA H2-8 2DL TFE 600/3/ NA H2-9 2DL TFD 480/3/ NA M4-5 2DL3-075E-TFC /3/ NA M4-8 2DL3-075E-TFE 600/3/ NA M4-9 2DL3-075E-TFD 480/3/ NA H2-5 2DA TFC /3/ NA H2-8 2DA TFE 600/3/ NA H2-9 2DA TFD 480/3/ NA M4-5 2DA3-075E-TFC /3/ NA M4-8 2DA3-075E-TFE 600/3/ NA M4-9 2DA3-075E-TFD 480/3/ NA H2-5 3DA TFC /3/ NA H2-8 3DA TFE 600/3/ NA H2-9 3DA TFD 480/3/ NA M4-5 3DA3-075E-TFC /3/ NA M4-8 3DA3-075E-TFE 600/3/ NA M4-9 3DA3-075E-TFD 480/3/ NA

31 UNIT P705-WCS, MCS, SCS Table 15 al Data Water-Cooled/Remote Condensing Units Copeland Compressors P705-WCS Water-Cooled (Sizes ); P705-MCS Sea Water-Cooled (Sizes ); P705-SCS Remote Compressor (Sizes ) R-22, R-404A and R-507 High and Medium Temperature (cont) Copeland Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s Qty Hp OUT 100-1H2-5 3DB TFC /3/ NA H2-8 3DB TFE 600/3/ NA H2-9 3DB TFD 480/3/ NA M4-5 3DB3-100E-TFC /3/ NA M4-8 3DB3-100E-TFE 600/3/ NA M4-9 3DB3-100E-TFD 480/3/ NA H2-5 3DS TFC /3/ NA H2-8 3DS TFE 600/3/ NA H2-9 3DS TFD 480/3/ NA M4-5 3DS3-150E-TFC /3/ NA M4-8 3DS3-150E-TFE 600/3/ NA M4-9 3DS3-150E-TFD 480/3/ NA H2-5 4DA TSK /3/ NA H2-8 4DA TSE 600/3/ NA H2-9 4DA TSK 480/3/ NA M4-5 4DA3-200E-TSK /3/ NA M4-8 4DA3-200E-TSE 600/3/ NA M4-9 4DA3-200E-TSK 480/3/ NA H2-5 4DH TSK /3/ NA H2-8 4DH TSE 600/3/ NA H2-9 4DH TSK 480/3/ NA M4-5 4DH3-250E-TSK /3/ NA M4-8 4DH3-250E-TSE 600/3/ NA M4-9 4DH3-250E-TSK 480/3/ NA H2-5 4DJ TSK /3/ NA H2-8 4DJ TSE 600/3/ NA H2-9 4DJ TSK 480/3/ NA M4-5 4DJ3-300E-TSK /3/ NA M4-8 4DJ3-300E-TSE 600/3/ NA M4-9 4DJ3-300E-TSK 480/3/ NA H2-5 6DH TSK /3/ NA H2-8 6DH TSE 600/3/ NA H2-9 6DH TSK 480/3/ NA M4-5 6DH3-350E-TSK /3/ NA M4-8 6DH3-350E-TSE 600/3/ NA M4-9 6DH3-350E-TSK 480/3/ NA H2-8 6DJ TSE 600/3/ NA H2-9 6DJ TSN 480/3/ NA M4-8 6DJ3-400E-TSE 600/3/ NA M4-9 6DJ3-400E-TSN 480/3/ NA *Condensing units have factory-installed contactors that meet the listed electrical characteristics. 31

32 UNIT P705-WCS, MCS,SCS Table 16 al Data Water-Cooled/Remote Condensing Units Copeland Compressors P705-WCS Water-Cooled (Sizes ); P705-MCS Sea Water-Cooled (Sizes ); P705-SCS Remote Compressor (Sizes ) R-22, R-404A and R-507 Low Temperature Copeland Qty Hp OUT 008-1L2-2 KAMA-0075-CAV /1/ NA L2-5 KAMA-0075-TAC /3/ NA L4-2 KAMB-007E-CAV /1/ NA L4-5 KAMA-007E-TAC /3/ NA L2-2 KAJB-0100-CAV /1/ NA L2-5 KAJA-0101-TAC /3/ NA L4-2 KAJB-010E-CAV /1/ NA L4-5 KAJA-011E-TAC /3/ NA L2-2 KAKB-0200-CAV /1/ NA L2-5 KAKA-020-TAC /3/ NA L4-2 KAKB-011E-CAV /1/ NA L4-2 KALB-015E-CAV /1/ NA L4-5 KALA-016E-TAC /3/ NA L2-2 EADB-0200-CAB 240/1/ NA L2-5 EADA-0200-TAC /3/ NA L4-2 EADB-021E-CAB 240/1/ NA L4-5 EADA-020E-TAC /3/ NA L2-2 EAVB-0210-CAV /1/ NA L2-5 EAVA-0210-TAC /3/ NA L2-9 EAVA-0210-TAD 480/3/ NA L4-2 EAVB-021E-CAV /1/ NA L4-5 EAVA-021E-TAC /3/ NA L4-8 EAVA-21E-TAE 600/3/ NA L4-9 EAVA-021E-TAD 480/3/ NA L2-2 LAHB-0311-CAB 240/1/ NA L2-5 LAHA-0310-TAC /3/ NA L2-8 LAH TAE 600/3/ NA L2-9 LAHA-0310-TAD 480/3/ NA L4-2 LAHB-032E-CAB 240/1/ NA L4-5 LAHA-032E-TAC /3/ NA L4-8 LAHB-032E-TAE 600/3/ NA L4-9 LAHB-032E-TAD 480/3/ NA L2-2 2DF CFB 240/1/ NA L2-5 2DF TFC /3/ NA L2-8 2DF TFE 600/3/ NA L2-9 2DF TFD 480/3/ NA L4-2 2DF3-030E-CFB 240/1/ NA L4-5 2DF3-030E-TFC /3/ NA L4-8 2DF3-030E-TFE 600/3/ NA L4-9 2DF3-030E-TFD 480/3/ NA L2-5 2DL TFC /3/ NA L2-8 2DL TFE 600/3/ NA L2-9 2DL TFD 480/3/ NA L4-5 2DL3-040E-TFC /3/ NA L4-8 2DL3-040E-TFE 600/3/ NA L4-9 2DL3-040E-TFD 480/3/ NA L2-5 2DA TFC /3/ NA L2-8 2DA TFE 600/3/ NA L2-9 2DA TFD 480/3/ NA L4-5 2DA3-060E-TFC /3/ NA L4-8 2DA3-060E-TFE 600/3/ NA L4-9 2DA3-060E-TFD 480/3/ NA L2-5 3DA TFC /3/ NA L2-8 3DA TFE 600/3/ NA L2-9 3DA TFD 480/3/ NA L4-5 3DA3-060E-TFC /3/ NA L4-8 3DA3-060E-TFE 600/3/ NA L4-9 3DA3-060E-TFD 480/3/ NA

33 UNIT P705-WCS, MCS,SCS Table 16 al Data Water-Cooled/Remote Condensing Units Copeland Compressors P705-WCS Water-Cooled (Sizes ); P705-MCS Sea Water-Cooled (Sizes ); P705-SCS Remote Compressor (Sizes ) R-22, R-404A and R-507 Low Temperature (cont) Copeland Evaporator Motor LRA Locked Rotor s Minimum Current acity Maximum Overcurrent Protection RLA Rated Load s Qty Hp OUT 080-1L2-5 3DB TFC /3/ NA L2-8 3DB TFE 600/3/ NA L2-9 3DB TFD 480/3/ NA L4-5 3DB3-075E-TFC /3/ NA L4-8 3DB3-075E-TFE 600/3/ NA L4-9 3DB3-075E-TFD 480/3/ NA L2-5 3DF TFC /3/ NA L2-8 3DF TFE 600/3/ NA L2-9 3DF TFD 480/3/ NA L4-5 3DF3-090E-TFC /3/ NA L4-8 3DF3-090E-TFE 600/3/ NA L4-9 3DF3-090E-TFD 480/3/ NA L2-5 3DS TFC /3/ NA L2-8 3DS TFE 600/3/ NA L2-9 3DS TFD 480/3/ NA L4-5 3DS3-100E-TFC /3/ NA L4-8 3DS3-100E-TFE 600/3/ NA L4-9 3DS3-100E-TFD 480/3/ NA L2-5 4DL TFC /3/ NA L2-8 4DL TFE 600/3/ NA L2-9 4DL TFD 480/3/ NA L4-5 4DL3-150E-TFC /3/ NA L4-8 4DL3-150E-TFE 600/3/ NA L4-9 4DL3-150E-TFD 480/3/ NA L2-5 4DT TFC /3/ NA L2-8 4DT TFE 600/3/ NA L2-9 4DT TFD 480/3/ NA L4-5 4DT3-220E-TFC /3/ NA L4-8 4DT3-220E-TFE 600/3/ NA L4-9 4DT3-220E-TFD 480/3/ NA L2-5 6DL TSK /3/ NA L2-8 6DL TSE 600/3/ NA L2-9 6DL TSK 480/3/ NA L4-5 6DL3-270E-TSK /3/ NA L4-8 6DL3-270E-TSE 600/3/ NA L4-9 6DL3-270E-TSK 480/3/ NA L2-5 6DT TSK /3/ NA L2-8 6DT TSE 600/3/ NA L2-9 6DT TSK 480/3/ NA L4-5 6DT3-300E-TSK /3/ NA L4-8 6DT3-300E-TSE 600/3/ NA L4-9 6DT3-300E-TSK 480/3/ NA *Condensing units have factory-installed contactors that meet the listed electrical characteristics. 33

34 Table 17 Pressure Loss of Liquid Refrigerants in Liquid Line Risers LIQUID LINE RISE (ft) REFRIGERANT Pressure Drop (Psig) and Subcooling Loss (F) Psig F Psig F Psig F Psig F Psig F Psig F Psig F Psig F Psig F R R-507, R-404A NOTE: Based on 110 F liquid temperature at bottom of riser. Table 18 Valve or Fitting Friction Expressed In Equivalent Length of Feet VALVE/FITTING TYPE L COPPER TUBE OD (in.) 1/ 2 5/ 8 7/ / / / / / / / / / / 8 Globe Valve (Open) Angle Valve (Open) Turn Through Tee Tee (Straight Through) or Sweep Below 3 / / / / Elbow or Reducing Tee (Straight Through)

35 Table 19 Line Sizes for R-22 Refrigerant P705 UNIT CAPACITY BTUH +40 F SST Equivalent Lengths (ft) +20 F SST Equivalent Lengths (ft) +10 F SST Equivalent Lengths (ft) SUCTION LINE SIZE (in.) LIQUID LINE SIZE (in.) 0 F SST Equivalent Lengths (ft) 10 F SST Equivalent Lengths (ft) 20 F SST Equivalent Lengths (ft) Receiver to Expansion Valve Equivalent Lengths (ft) ,000 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 1 /2 3 /8 3 /8 3 /8 3 /8 1 /2 1 /2 3 /8 3 /8 3 /8 3 /8 1 /2 1 /2 3 /8 3 /8 3 /8 1 /2 1 /2 1 /2 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3,000 4,000 6,000 1 /2 1 /2 1 /2 5 /8 5 /8 5 /8 1 /2 1 /2 5 /8 5 /8 5 /8 5 /8 1 /2 5 /8 5 /8 5 /8 7 /8 7 /8 5 /8 5 /8 5 /8 5 /8 7 /8 7 /8 1 /2 5 /8 5 /8 7 /8 7 /8 7 /8 5 /8 5 /8 7 /8 7 /8 7 /8 7 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 9,000 1 /2 5 /8 5 /8 5 /8 7 /8 7 /8 1 /2 5 /8 5 /8 5 /8 7 /8 7 /8 5 /8 5 /8 7 /8 7 /8 7 /8 7 /8 5 /8 7 /8 7 /8 7 /8 7 /8 7 /8 5 /8 7 /8 7 /8 7 /8 7 /8 7 /8 5 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 12,000 5 /8 5 /8 5 /8 7 /8 7 /8 7 /8 5 /8 5 /8 7 /8 7 /8 7 /8 7 /8 5 /8 7 /8 7 /8 7 /8 7 /8 7 /8 5 /8 7 /8 7 /8 7 /8 7 /8 1 1 /8 7 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 15, /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 18,000 5 /8 7 /8 7 /8 7 /8 7 /8 1 1 /8 5 /8 7 /8 7 /8 7 /8 7 /8 1 1 /8 7 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 7 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 7 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 3 /8 3 /8 3 /8 3 /8 1 /2 1 /2 24,000 5 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 7 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 7 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 7 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 3 /8 3 /8 1 /2 1 /2 1 /2 1 /2 30, /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 36, /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 42, /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 48,000 7 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 1 /2 1 /2 1 /2 1 /2 1 /2 5 /8 54,000 7 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 /2 1 /2 1 /2 1 /2 5 /8 5 /8 60,000 7 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 /2 1 /2 1 /2 5 /8 5 /8 5 /8 66, /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 72, /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 78, /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 1 /2 1 /2 5 /8 5 /8 5 /8 5 /8 1 /2 1 /2 5 /8 5 /8 5 /8 7 /8 84, /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 1 /8 90, /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 1 /8 120, /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 1 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 150, /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 1 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 180, /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 1 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 1 5 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 210, /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 2 5 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 5 /8 7 /8 7 /8 7 /8 7 /8 7 /8 5 /8 7 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 240, /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 7 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 300, /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 2 1 /8 2 5 /8 3 1 /8 3 1 /8 3 1 /8 3 5 /8 7 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 360, /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 7 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 480, /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 2 5 /8 3 1 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 2 5 /8 3 1 /8 3 5 /8 3 5 /8 3 5 /8 4 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 600, /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 2 1 /8 2 5 /8 3 1 /8 3 1 /8 3 1 /8 3 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 4 1 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 SST Saturated Suction Temperature NOTES: 1. sizes indicate maximum suction line sizes that should be used for risers. Riser size should not exceed horizontal size. Properly placed suction traps must also be used for adequate oil return. 2. All sizes shown are for O.D. Type L copper tubing. 3. Suction line sizes selected at pressure drop equivalent to 2 F. Reduce estimate of system capacity accordingly. 4. Recommended liquid line size may increase with reverse cycle hot gas systems. 5. If system load drops below 40%, double suction risers are recommended. 35

36 Table 20 Line Sizes for R-404A, R-507 Refrigerant P705 UNIT CAPACITY BTUH +20 F SST Equivalent Lengths (ft) +10 F SST Equivalent Lengths (ft) 10 F SST Equivalent Lengths (ft) SUCTION LINE SIZE (in.) LIQUID LINE SIZE (in.) 20 F SST Equivalent Lengths (ft) 30 F SST Equivalent Lengths (ft) 40 F SST Equivalent Lengths (ft) Receiver to Expansion Valve Equivalent Lengths (ft) ,000 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 1 /2 3 /8 3 /8 3 /8 1 /2 1 /2 1 /2 3 /8 3 /8 1 /2 1 /2 1 /2 1 /2 3 /8 3 /8 1 /2 1 /2 1 /2 5 /8 3 /8 1 /2 1 /2 1 /2 5 /8 5 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3,000 3 /8 3 /8 1 /2 1 /2 1 /2 5 /8 3 /8 1 /2 1 /2 1 /2 5 /8 5 /8 1 /2 1 /2 5 /8 5 /8 5 /8 7 /8 1 /2 1 /2 5 /8 5 /8 7 /8 7 /8 1 /2 1 /2 5 /8 5 /8 7 /8 7 /8 1 /2 1 /2 5 /8 5 /8 7 /8 7 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 4,000 3 /8 1 /2 1 /2 1 /2 5 /8 5 /8 1 /2 1 /2 1 /2 5 /8 5 /8 7 /8 1 /2 5 /8 5 /8 5 /8 7 /8 7 /8 1 /2 5 /8 5 /8 7 /8 7 /8 7 /8 5 /8 5 /8 5 /8 7 /8 7 /8 7 /8 1 /2 5 /8 5 /8 7 /8 7 /8 7 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 6, /8 9,000 5 /8 5 /8 7 /8 7 /8 7 /8 7 /8 5 /8 5 /8 7 /8 7 /8 7 /8 7 /8 5 /8 7 /8 7 /8 7 /8 7 /8 1 1 /8 5 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 5 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 5 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 3 /8 3 /8 3 /8 3 /8 3 /8 3 /8 12,000 5 /8 7 /8 7 /8 7 /8 7 /8 7 /8 5 /8 7 /8 7 /8 7 /8 7 /8 1 1 /8 7 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 3 /8 3 /8 3 /8 3 /8 3 /8 1 /2 15,000 18,000 24, /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 30,000 7 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 3 /8 1 /2 1 /2 1 /2 1 /2 1 /2 36,000 7 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 /2 1 /2 1 /2 1 /2 1 /2 5 /8 42, /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 48, /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 3 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 54, /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 5 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 60, /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 /2 1 /2 1 /2 5 /8 5 /8 5 /8 1 /2 1 /2 1 /2 5 /8 5 /8 5 /8 1 /2 1 /2 5 /8 5 /8 5 /8 5 /8 66, /8 13 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 1 /8 13 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 3 /8 15 /8 1 5 /8 1 5 /8 1 5 /8 1 5 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 15 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 15 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 72, /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 1 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 5 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 5 /8 1 5 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 78, /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 5 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 5 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 5 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 5 /8 5 /8 5 /8 5 /8 5 /8 7 /8 84, /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 90, /8 1 3 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 1 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 120, /8 1 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 1 3 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 1 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 5 /8 5 /8 5 /8 5 /8 7 /8 7 /8 150, /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 1 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 2 5 /8 180, /8 2 1 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 1 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 210, /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 5 /8 7 /8 7 /8 7 /8 7 /8 1 1 /8 7 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 7 /8 7 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 240, /8 2 1 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 2 5 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 300, /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 5 /8 3 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 4 1 /8 2 5 /8 2 5 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 7 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 360, /8 2 1 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 2 1 /8 2 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 2 5 /8 2 5 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 2 5 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 4 1 /8 1 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 480, /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 2 5 /8 2 5 /8 2 5 /8 2 5 /8 3 5 /8 3 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 4 1 /8 4 1 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 4 1 /8 4 1 /8 1 1 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 600, /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 2 5 /8 2 5 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 3 1 /8 3 1 /8 3 1 /8 3 5 /8 4 1 /8 4 1 /8 3 1 /8 3 1 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 4 1 /8 5 1 /8 3 1 /8 3 5 /8 3 5 /8 4 1 /8 4 1 /8 5 1 /8 1 1 /8 1 3 /8 1 3 /8 1 5 /8 1 5 /8 1 5 /8 SST Saturated Suction Temperature NOTES: 1. sizes indicate maximum suction line sizes that should be used for risers. Riser size should not exceed horizontal size. Properly placed suction traps must also be used for adequate oil return. 2. All sizes shown are for O.D. Type L copper tubing. 3. Suction line sizes selected at pressure drop equivalent to 2 F. Reduce estimate of system capacity accordingly. 4. Recommended liquid line size may increase with reverse cycle hot gas systems. 5. If system load drops below 40%, double suction risers are recommended. 36

37 LINE SIZE OD (in.) REFRIGERANT Table 21 Refrigerant Operating Weight (Lbs) in Copper Lines REFRIGERANT PER 100 LINEAR FEET L TUBING (lbs) Liquid Line Hot Gas Line SUCTION LINE AT SUCTION TPERATURE (F) / 8 R R-507, R-404A / 2 R R-507, R-404A / 8 R R-507, R-404A / 8 R R-507, R-404A / 8 R R-507, R-404A / 8 R R-507, R-404A / 8 R R-507, R-404A / 8 R R-507, R-404A / 8 R R-507, R-404A / 8 R R-507, R-404A / 8 R R-507, R-404A / 8 R R-507, R-404A

38 Table 22 System Troubleshooting Chart PROBL POSSIBLE CAUSES POSSIBLE CORRECTIVE STEPS Compressor Will Not Run 1. Main switch open. 1. Close switch. 2. Fuse blown. 2. Check electrical circuits and motor winding for shorts or grounds. Investigate for possible overloading. Replace fuse after fault is corrected. 3. Thermal overloads tripped. 3. Overloads are automatically reset. Check unit closely when unit comes back on line. 4. Defective contactor or coil. 4. Repair or replace defective part. 5. System shut down by safety devices. 5. Determine type and cause of shutdown and correct it before resetting safety switch. 6. No cooling required. 6. None. Wait unit calls for cooling. 7. Liquid line solenoid will not open. 7. Repair or replace coil. 8. Motor electrical trouble. 8. Check motor for open windings, short circuit or burn out. 9. Loose wiring. 9. Check all wire junctions. Tighten all terminal screws. Compressor Noisy or Vibrating 1. Flooding of refrigerant into crankcase. 1. Check setting of expansion valves. 2. Improper piping support on suction or 2. Relocate, add or remove hangers. liquid line. 3. Worn compressor. 3. Replace. 4. Scroll compressor rotation reversed. 4. Rewire for phase change. High Discharge Pressure 1. Noncondensables in system. 1. Remove the noncondensables. 2. System overcharged with refrigerant. 2. Remove excess refrigerant. 3. Discharge shutoff valve partially closed. 3. Open valve. 4. Fan not running. 4. Check electrical circuit. 5. Head pressure control setting. 5. Adjust control setting. 6. Dirty condenser coil. 6. Clean condenser coil. Low Discharge Pressure 1. Faulty condenser temperature regulation. 1. Check condenser control operation. 2. Suction shutoff valve partially closed. 2. Open valve. 3. Insufficient refrigerant in system. 3. Check for leaks. Repair and add charge. 4. Low suction pressure. 4. See corrective steps for low suction pressure. 5. Variable head pressure valve. 5. Check valve setting. High Suction Pressure 1. Excessive load. 1. Reduce load or add additional equipment. 2. Expansion valve overfeeding. 2. Check remote bulb. Regulate superheat. Low Suction Pressure 1. Lack of refrigerant. 1. Check for leaks. Repair leak and add charge. 2. Evaporator dirty or iced. 2. Clean evaporator. 3. Clogged liquid line filter drier. 3. Replace cartridge(s). 4. Clogged suction line or compressor 4. Clean strainers. suction gas strainers. 5. Expansion valve malfunctioning. 5. Check and reset for proper superheat. 6. Condensing temperature too low. 6. Check means for regulating condensing temperature. Low or No Oil Pressure 1. Clogged suction oil strainer. 1. Clean. 2. Excessive liquid in crankcase. 2. Check crankcase heater. Reset expansion valve for higher superheat. Check liquid line solenoid valve operation. 3. Low oil pressure safety switch defective. 3. Replace oil pressure safety switch. 4. Worn oil pump. 4. Replace oil pump. 5. Oil pump reversing gear stuck in wrong 5. Reverse direction of compressor rotation. position. 6. Worn bearings. 6. Replace compressor. 7. Low oil level. 7. Add oil. 8. Loose fitting on oil lines. 8. Check and tighten system. 9. Pump housing gasket leaks. 9. Replace gasket. Compressor Loses Oil 1. Lack of refrigerant. 1. Check for leaks and repair. Add refrigerant. 2. Excessive compression ring blowby. 2. Replace compressor. 3. Refrigerant flood-back. 3. Maintain proper superheat at compressor. 4. Improper piping or traps. 4. Correct piping. Compressor Thermal Protector Switch Open 1. Operating beyond design conditions. 1. Add facilities so that conditions are within allowable limits. 2. Discharge valve partially shut. 2. Open valve. 3. Blown valve plate gasket. 3. Replace gasket. 4. Dirty condenser coil. 4. Clean coil. 5. Overcharged system. 5. Reduce charge. 38

39 Adding Oil If oil is needed, allow the system to pump down. See Tables 23 and 24 to select proper oil. 1. Turn off all power to the unit. 2. Close the suction and discharge valves at the compressor. 3. Partially unscrew the filler hole pipe plug. Allow pressure to bleed before totally removing the plug. (The filler hole is located just above and to the left of the crankcase sight glass on most compressors.) 4. Add manufacturer approved oil through the filler hole. Be sure oil has not been exposed to air or other contaminants. 5. Replace and tighten filler hole pipe plug. 6. Re-open the compressor suction and discharge valves. 7. Restart the unit. Semi-Hermetic Compressor Oil level must be maintained at 1 /2 or 3 /4 full as indicated on the sight glass. If oil level is low, add manufacturer approved oil to the compressor. Do not over fill. Check oil level after 2 hours. Check oil level 2 days after the addition of oil. Excessive oil quantity in a system may lead to liquid slugging and compressor damage. A well balanced unit should not require any additional oil after a week of operation. If a system is requiring more oil after one week of operation, the unit must be inspected to find the location of the trapped oil. Hermetic and Scroll Compressors Hermetic and scroll compressors are shipped from the factory with the required charge of oil already in the compressor. No oil needs to be added during installation. Napthenic Mineral Oils The BR, QR, and Scroll compressors used in HCFC R-22 applications use Witco LP- 200 or Sontex 200-LT, both white oils. Since these oils are not available through normal refrigeration wholesalers, for field top-off the use of any approved mineral oil (MO) or alkyl benzene (AB) is permissible. Suniso 3GS, Capella WF32 and Calumet RO15 (pale yellow oils) are available through refrigeration wholesalers. These oils are compatible if mixed and can be used on both high and low temperature systems. Polyolester Lubricants The following polyolester lubricants have been tested and approved for use in Copeland compressors: Copeland Ultra 22CC Mobil EAL Arctic 22CC ICI Emkarate RL 32CF Thermal Zone 22CC These POE s must be used if HFC refrigerants are used in the system. They are also acceptable for use with any of the traditional refrigerants or interim blends and are compatible with mineral oils. They can therefore be mixed with mineral oils when used in systems with CFC or HCFC refrigerants. These lubricants are compatible with one another and can be mixed. The ZP scroll compressors used in HFC R-410A applications use a POE oil not available through wholesalers. Any of the POE oils listed above may be used to replace up to 50% of the original oil if necessary. Users of POE s must be aware of the hygroscopic nature of these lubricants. Care must be taken to avoid moisture absorption during handling. Alkyl Benzenes Copeland Ultra 200, Zerol 200TD, Soltex AB 200A and Thermal Zone 200 are alkyl benzene (AB) lubricants. Copeland recommends these lubricants for use as mixtures with mineral oil (MO) when using the Interim Blends such as R-401A, R-401B, R-402A, R-408A, and R-409A (MP-39, MP-66, HP80, FX-10 and FX-56). A minimum of 50% AB is required with these mixtures to assure proper oil return to the compressor. Shell and Witco R are mixtures of AB/MO. If these lubricants are used in a retrofit situation, virtually all of the existing MO must be drained prior to re-filling with these products to assure a minimum 50% AB content. 39

40 A M Polyolester Oils Mineral Oils Alkyl Benzene Oils Alkyl Benzene/ Mineral Oil Mix Acceptable Alternative Mixture of Mineral Oil and Alkyl Benzene (AB) with minimum 50% AB POE s Polyolester oils P Preferred Lubricant Choice Table 23 Refrigeration Oils Copeland Compressor REFRIGERATION OILS R-22 R-404A/R-507 Copeland Ultra 22CC A P Copeland 3MA A P (1,3) Mobil EAL ARCTIC 22 CC A P ICI (Virginia KMP) KARATE RL 32CF A P Thermal Zone 22CC A P Witco Suniso 3GS P Texaco Capella WF32 P Calumet RO15 P NOT Witco (2,3) P ACCEPTABLE Your Assurance LP-200 of Quality Penreco (2,3) ALL Totaline products Sontex 200-LTare backed with a one-year P warranty by Carrier Shritene Corporation, the world s largest manufacturer Copeland of air Ultra conditioning, 200 heating, A and Shreve Zerol 200 TD A refrigeration products. NOTES: 1. ZP Scroll A/C applications. 2. BR, QR and Scroll A/C applications. 3. Not available in field. NOT ACCEPTABLE Soltex Type AB-200A A Thermal Zone 200 A Shell A NOT Witco R A ACCEPTABLE Table 24 Refrigeration Oils Carlyle Compressor Carlyle Semi-Hermetic Compressors 06D, 06E R-22 LOW/MED/HIGH TP R-404A/R-507 LOW TP R-404A/R-507 MED TP R-404A/R-507 HIGH TP Zerol 150 RO15 E68 (Do not use SW68 for low temperature) SW68 E68 Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. REPLACENT COMPONENTS DIVISION LITERATURE NUMBER P705-2SI CARRIER CORPORATION CATALOG NO PRINTED IN U.S.A. REPLACES P705-1SI