February Photograph courtesy of R Carpenter

Transcription

1 February 2012 OO gauge Kits Standard and Narrow gauge Photograph courtesy of R Carpenter 4401 Andrew Barclay Lady Margaret as built in Lady Margaret 2-4-0T Kit is etched brass and nickel with whitemetal and brass castings, handrail knobs and name plates. Needs motor, gears, gearbox, wheels, pickups, solder/adhesive, paint and transfers. GWR No In 1929 Lady Margaret was rebuilt at Swindon. The engine was returned to Oswestry where she remained until withdrawn in Kit specification as above Lady Margaret as rebuilt by the GWR. Rolling Road A test bed for steam and diesel models. Will take steam locos from an 0-4-0T to a , including an LMS Garrett. Will take diesel from an to a Peak 1Co Co1. Gauge of road can be adjusted from 12mm to 21mm. Road is a kit and requires assembly,a base (mdf or plastic) and connection to a controller. Kit 6003 End view of road.

2 OO Lineside Posters and Timetables for all companies. Printed in colour on quality paper GWR Posters and timetables. (46 in pack) 4741 SR Posters and timetables. (54 in pack) 4742 LMS Posters and timetables. (46 in pack) 4743 LNER Posters and timetables. (49 in pack) 4749 BR 1970 s and 1980 s Posters. (64 in pack) 4750 Enamel Signs 1. 2 each of 32 signs Enamel Signs 2. 2 each of 24 signs Poster Boards for stations. Includes alternate headings of BRITISH RAILWAYS, GWR, SOUTHERN, LMS or LNER for the top of the poster board. 8 boards in etched brass Modern Notice Boards As seen at the entrance to stations. Includes posters, notices and timetables from the 1990 s Container Chains for securing containers to the Conflat they were carried on Speed Signs 14 signs, some with direction arrows. Road Work Lights Working Lights for single line traffic. Includes signs and barriers AWS Ramps 11 ramps of 2 different types. Traffic Lights Control Module An electronic module to control our traffic lights. Changes the lights through the sequence of long red, red/amber to green. Needs power supply of 9-16v, AC/DC Modern Mile Posts marking full and quarter mile distances Storage Tanks 2 square tanks with filler hatch and pipe outlet. One large, one small.

3 OO OHLE 25kV OHLE Supports to model the 25kV catenary as installed on the West Coast main line and other early electrified lines. The girder or leg is a single piece brass etch which rolls up around a former. The former prevents the etch collapsing while the bends are made. After sliding the former out the girder or leg is rigid and has only one open joint. Portal Supports 4524 Heavy 4 track Light 2 track Light 4 track. Available in 1 or 3 packs Light with ladder lattice legs Light Girder extension, 80mm long Ladder/lattice legs. Kit 4530 Light 2 track portal. Portal Fittings Fittings for both light and heavy portals. These are lost wax castings that mount on 1.5mm tube (not included). Kit 4580 Register Arm with Kit 4581 Support Pulley. 3

4 OO Trolleys Kit 4485 Wickham Type 27 Ganger s Trolley The common motorized trolley seen all over BR zipping along the tracks or parked beside the tracks. Kit 4480 Wickham Type 17 Ganger s Trolley The motorized trolley built from 1930 and used by the big four. Many lasted into BR. Wickham Type 27 Kit makes a rolling model, is etched nickel and includes bearings and wheels. To help the modeller who wishes to motorise this model, top hat bearings are included. Needs solder/adhesive, paint and transfers. Wickham Type 17 Kit makes a rolling model, is etched nickel and includes bearings and wheels. To help the modeller who wishes to motorise this model, top hat bearings are included. Needs solder/adhesive, paint and transfers Wickham Trailer Can be used as a trailer or a hand trolley. Kit 4640 Wood trolley, as used from the 1920 s. Wickham Trailer For use behind the Type 27 or if reduced in width behind the Type 17. Kit is etched nickel and includes bearings and wheels. Needs solder/adhesive, paint and transfers. Kit 4641 Modern steel trolley as carried around by the rail contractors. 4 Platelayer s Trolleys The Ganger s wheel barrow seen all over the railway. Used to move chairs and tools needed to maintain the track, often dumped beside the track. Inc. wheels. E/n. Needs solder/adhesive, paint.

5 OO The Eclipse Bagnall steam loco converted to an electric loco in Kit makes a rolling model. Needs solder/adhesive, couplings, paint and transfers PB&SSR ELECTRIC Kit makes a rolling model. Needs solder/adhesive, couplings, paint, transfers to complete Wickham Type 27. Used for track gangs and as a railbus. These diminutive trolleys were supplied to narrow gauge railways across the world. Clever design enabled the same vehicle to be built to a variety of different gauges Bolster Wagon GVT bolster wagon. Includes wheels. Can be built as a flat wagon Manager s Wagon GVT inspection wagon used to check out the line. Inc. wheels Tank Wagon Used for hauling tar up the line. Inc. wheels Tipper Wagon GVT wood built tipper. Inc. wheels GVT First Coach Needs adhesive, paint, transfers and couplings GVT Coach Needs adhesive, paint, transfers and couplings.

6 OO GVT Tram coach Needs adhesive, paint, transfers and couplings. Coaches have a one piece coach body that folds into a rigid box with no awkward corner joints to make. Kits include seats and wheels. Etched brass. All need solder/adhesive, paint, transfers and couplings. Trestle, with decking and rails omitted for clarity. Steel Trestle Kit for a steel trestle. Height, length and design can be varied, can be built straight or curved. Built from 3 modules Deck Girder - 83mm long, 9mm high with rivet detail. (Not inc. - track, support timbers, walkway and handrails.) Trestle - two 60mm high A frames with tie girders. Trestle Extension - Increases trestle height in 58mm steps. A 234mm high trestle can be built.. Bending Jig - Simplifies bending parts. NOTES This list describes the current range of OO kits from N Brass Locomotives. All items are kits with either nickel silver etches, brass etches, lost wax brass castings, whitemetal castings or a combination of some or all of the above. Where appropriate they also contain additional items, e.g. wire for handrails. They also include instructions describing and illustrating the assembly of the kit. Many kits require no additional parts except adhesive/solder, and paint to complete. The more complex kits require further items, e.g. motor, wheels and gearbox.. Each description lists the further items required. ILLUSTRATIONS Illustrations in this catalogue are actual size, unless stated.. 6

7

8