Matson Programmable Voltage Sensitive Relay MA98411

Size: px
Start display at page:

Download "Matson Programmable Voltage Sensitive Relay MA98411"

Transcription

1 Matson Programmable Voltage Sensitive Relay MA98411

2 Matson Programmable Voltage Sensitive Relay The MPVSR is a solid state electronic relay which is activated by sensing the voltage of the circuits it is connected to. The voltages at which it will either open or close are able to be programmed by the user, meaning this product is suitable for a huge variety of applications. An example of this is variable voltage output alternators increasingly found in modern vehicles. This unit can be programmed to suit the characteristics of almost all 12 volt charging systems, and handle currents of up to 150amps continuous (at 12VDC). The cut in and cut out activations are also able to be time delayed to prevent VSR chatter, as well as being able to program an alarm activation at a user defined voltage level. The MPVSR is truly the next generation of charging control. Primary Applications Parallel Charging Combining separate batteries or banks of batteries together to charge from a single source or power. Low Voltage Disconnect Automatically switching off an electrical load once the battery reaches a user defined voltage. Automatic paralleling of batteries Automatically combines two battery banks for emergency power situations. Automatic load switching Using the control terminals, the MPVSR can be a switch that will allow a load through it as long as the supply voltage is between the user defined ranges. A Heavy Duty Relay For switching loads up to 150Amps.

3 FEATURES Solid state design means no moving parts to fail Fully user programmable to set voltage and time delays User programmable to set as either normally open or normally closed Isolated design means circuit cannot backfeed Isolation between control and load circuits LED indicators and display Alarm output for remote peace of mind Water and dust resistant enclosure Can be mounted in any orientation Over temperature protection Separate emergency over-ride connection 5 year warranty WARNING Make sure you are familiar with the operation and installation requirements of the MPVSR before installing or using. Please take into account the environmental limitations of the product. The device is water and dust resistant, but is not designed to be installed in wet or excessively dusty environments. These influences may shorten the life of the product and are not covered by warranty. Never leave the load terminals uncovered, there is a high risk of short circuit, which may damage the device and it s surroundings, including people. The device should not be operated by children. Electricity can be dangerous! Short circuits can create sparks which will ignite any present flammable substances. It is critical to ensure the unit is installed in a well ventilated area AWAY FROM ANY SOURCES OF FLAMMABLE SUBSTANCES. This includes batteries and fuel!

4 LAYOUT

5 INSTALLATION Correct installation is critical for trouble free operation of the MPVSR. Failure to properly install the unit may cause it to not work correctly, and may also void its warranty. For best results please observe the following instructions. Choose a suitable location where the MPVSR can be mounted. Make sure there is adequate ventilation to allow the unit to dissipate heat, and try to install it in an area that is not too hot. Engine bays are not ideal, but if adequately mounted it is an alternative. If mounting in an engine bay, be sure to shield the unit from heat, dust and water. In other applications, avoid moisture, dust and high vibration areas. The unit can be mounted in any orientation (even upside down) but must be on a hard flat surface. Make sure you maintain at least 5cm of clearance between the unit and any other objects. Utilise all four mounting points, using appropriate fasteners for the application. Do not over tighten. WIRING It is very important to use the correct cable for your application. If the cable gauge is too small you will suffer voltage drop, reduced current, over heating of cabling and general poor performance, even failure. If you have any doubts, consult the place of purchase for the cable, the cable manufacturer, or an auto electrician. They will advise you on the continuous load the cable can carry. This MUST match the load of your application. Generally, when it comes to cable, bigger is better, and there is no substitute for good quality cable and terminals. Make sure the supply current or power is disconnected before connecting anything to the MPVSR! It is recommended that you install an inline fuse or circuit breaker as the load protection. The fuse or circuit breaker should be rated to suit the application, and should not exceed 150amps or the maximum rating of the load cable being used. Connect the required wiring to the control terminals, MAKING SURE TO USE THE CORRECT POLARITY! Connecting the polarity incorrectly will damage the unit and it will either need to be repaired or replaced. This is not covered by warranty. Note; if you do not require an alarm or manual over-ride switch, you do not need to connect anything to these terminals.

6 Note: It is very important to use appropriate terminations on your cables. Poor connections can result in overheating, damaging the MPVSR. For advice on termination please contact the place of purchase, an auto electrician, or The Matson Group. See below for termination examples. CRIMP TERMINALS FOR CONTROL TERMINATION COPPER LUG FOR LOAD TERMINATION

7 INITIAL SET UP Once the control wires are connected to the MPVSR and a power source, the device is ready to be programmed to the user s desired settings. It is worth keeping in mind that you may not need to alter the factory settings, which are listed in the table below. 12 Volt DC Upper Voltage Limit 13.7 Volts Upper Time Delay 5 Seconds Lower Voltage Limit 12.8 Volts Lower Time Delay 5 Seconds Alarm Voltage Limit 12.0 Volts Alarm Time Delay 10 Seconds State of Contacts Normally Open (n - o)

8 CONTROL PANEL STATE LCD DISPLAY RESET SET SELECTED CONTROL ACTIONS PUSH BUTTONS TO SELECT CONTROL ACTIONS To adjust the settings, observe the following procedure: NOTE; the buttons need to be pressed firmly in the centre or they will not register. This is to avoid accidental changes to programming by bumping the buttons. Press the SET button once, the screen will show OFF Press the SET button a second time. The screen will show the current setting, relating to whichever LED is illuminated around the screen. The first to come up will be the UPPER LIMIT IN VOLTS. If this setting does

9 not need to be changed you can cycle through the parameters using the UP and DOWN arrows. To change a value: When the value you want to change is displayed on the LED screen, press the SET button and the value on the screen will begin to flash. While the screen is flashing, use the UP and DOWN buttons to change the value. Pressing SET again will stop the screen flashing and save the value. Use the UP and DOWN buttons to cycle through to the next setting you would like to change, and repeat the process. Once you have set all the values to your requirements, take your hands off the unit. After 10 seconds of inactivity the unit will switch off. To reset the unit to the factory settings, follow the procedure above, cycle through the settings until you reach RESET. Press the SET button and see NO flashing. If you would like to reset the unit, use the UP or DOWN button to cycle through to see YES and press SET. This will restore the unit to factory settings and the screen will read RST.

10 COMMON APPLICATIONS Dual Battery Charging One of the major uses of the MPVSR is in dual battery charging applications. The MPVSR is used to put the two batteries or banks of batteries into parallel once the primary battery or bank reaches a certain voltage. In a 4x4 application, where a secondary battery is used for accessories such as lights, fridges or winches, it is important to protect the vehicles starting battery from being flattened by the accessories, making sure you can always start the vehicle and drive away. The MPVSR, installed between the starting battery and the secondary battery, can put the batteries in parallel once the starting battery is charged, or reaches a user defined voltage, allowing charging of both batteries to occur while the vehicle is driving. If a load is placed on the batteries whilst in parallel, and the starting battery drops to a pre-determined voltage, the MPVSR will disconnect the two batteries, allowing the secondary battery to power the accessories and protecting the starting battery. The ability to determine the cut-in and cut-out voltages of the MPVSR, specific to the vehicle, makes this product perfect for modern vehicles with VARIABLE VOLTAGE OUTPUT ALTERNATORS. Setting Guide: (note, this setup requires the MPVSR bet programmed normally open ) UPPER LIMIT IN VOLTS: This is the voltage that, when reached by the starting/primary battery, the MPVSR will put the batteries in parallel and charge both batteries. For vehicles with a VARIABLE VOLTAGE ALTERNATOR, this will need to be set relatively low, at a point just below the higher voltage output of the alternator. You will need to contact the manufacturer or dealership to find this information. LOWER LIMIT IN VOLTS: This is the voltage level that, when reached by the starting/primary battery, the MPVSR will disconnect the batteries from the parallel circuit and isolate the starting/primary battery. This needs to be set at a voltage level greater than the minimum voltage level required to start the vehicle UPPER DELAY IN SECS: This setting, in seconds, is the amount of delay the MPVSR will wait to put the batteries in parallel, after the primary/ starting battery reaches the UPPER LIMIT IN VOLTS. This delay stops VSR chatter, caused by the primary battery voltage dropping when the batteries are put in parallel and the VSR continuously connecting and

11 disconnecting the batteries. If VSR chatter is experienced, increase the delay in 20 second increments. LOWER DELAY IN SECS: This setting determines how long the primary/ starting battery will be allowed to remain at the lower limit in volts before the MPVSR cuts out and isolates the primary/starting battery. A delay is useful here because the voltage of the starting battery may drop below this point for a few seconds when starting the vehicle, but return to a safe level quickly. In this scenario you would not need to isolate the primary/ starting battery. DUAL BATTERY WIRING EXAMPLE + SENSE WIRE REMOTE OVERRIDE SWITCH BUZZER MUTE SWITCH (OPTIONAL) 12 Volt Primary Battery (Sensing) 12 Volt Secondary Battery (Charging)

12 Low Voltage Disconnect The MPVSR can be used as a low voltage cut-out device when wired in line between the load and the power source. This would be used in situations where it is important to make sure the power source is not drained too far, like a starting battery in a car, or a lithium battery being used as a power supply. In the car example, a flattened battery means you can t start the engine and you are stuck. The lithium battery power supply can be destroyed easily if it is discharged too far. In both case, low voltage protection will allow for peace of mind and longer life expectancy for the products involved. Setting Guide: (note, this setup requires the MPVSR bet programmed normally open ) UPPER LIMIT IN VOLTS: This is the setting that determines when the power would be re-connected and allow operation to resume once the power source has returned to an acceptable level. In the car example, this would be when the battery has been charged back to a safe voltage to start the vehicle. It can be as little as 0.1V above the LOWER LIMIT IN VOLTS. LOWER LIMIT IN VOLTS: This is the voltage level where you want to disconnect the load from the power source to prevent it getting too low. In the car scenario, this would be the voltage level where if it got any lower the battery would not be able to start the car. UPPER DELAY IN SECS: This is the delay setting for re-connecting the load to the power source. Delaying the re-connection allows the voltage at the power source to stabilise before the load is connected again. This is more important when the power supply is a battery. LOWER DELAY IN SECS: This is the delay setting for disconnecting the load. In the car scenario, without a delay set, the MPVSR might disconnect the load when you try to start the vehicle, as the large load when starting can drop the battery voltage significantly for a few seconds. After starting the voltage would generally rise again to a safe level, meaning it would not be necessary to disconnect the load from the battery. In this situation it could even prevent you starting the vehicle.

13 LOW VOLTAGE DISCONNECT WIRING EXAMPLE + SENSE WIRE REMOTE OVERRIDE SWITCH BUZZER MUTE SWITCH (OPTIONAL) LOAD 150A MAX 12 Volt Primary Battery (Sensing)

14 AUTOMATIC PARALLELING OF BATTERIES The MPVSR can be programmed to connect two batteries or banks together in parallel if the voltage of the primary battery gets to a predetermined voltage. For example, if the starting battery on a boat was going flat, the MPVSR could automatically connect it to the secondary or house batteries to enable it to start the motor. CAUTION: This functionality must be thought through carefully. If your starting battery is going flat, and you automatically connect your house batteries to it, and it continues to go flat without you knowing, you will be stuck with two flat battery banks! It is highly recommended to use an alarm when using this function, so you know when the batteries are in parallel. Setting Guide: (note, this setup requires the MPVSR bet programmed normally closed ) UPPER LIMIT IN VOLTS: This is the setting where the batteries will be disconnected from each other after the primary battery reaches a sufficient charge voltage. LOWER LIMIT IN VOLTS: This is the setting that determines when the batteries will be connected in parallel. This should be set at the point where the starting battery might no longer be able to start the motor, and would require assistance from another battery bank. UPPER DELAY IN SECS: This is the delay, in seconds, before the batteries are disconnected after the starting battery reaches a sufficient voltage level. LOWER DELAY IN SECS: This is the delay, in seconds, before the batteries are connected into parallel. This should be around the 10 second mark to accommodate for the voltage sag of the battery under a starting load.

15 AUTOMATIC PARALLELING WIRING EXAMPLE + SENSE WIRE BUZZER MUTE SWITCH (OPTIONAL) 12 Volt Primary Battery (Sensing) 12 Volt Secondary Battery (Charging)

16 AUTOMATIC LOAD SWITCHING The MPVSR can be programmed to perform automatic load switching, by using the control terminals for sensing a desired voltage range. This is particularly useful in remote or unmanned situation where equipment needs to be operated, but also protected from over-voltage and undervoltage damage scenarios. For example, a flashing light on a remote tower needs to be activated at night, but it is powered by a lithium battery bank that is very expensive. Wiring the light switch in series with the control terminals (positive or negative) and setting the upper and lower voltage limits to the desired range means that the light can be switched on and off as needed, but only if the battery voltage is within the safe range set by the user. Setting Guide: (note, this setup requires the MPVSR bet programmed normally open ) UPPER LIMIT IN VOLTS: This is the setting where the voltage would be re-connected to the light to allow it to operate as required again. In this example it would be the safe voltage level for the batteries to operate again. LOWER LIMIT IN VOLTS: This is the voltage level at which the light would be disconnected from the power source so as not to over-discharge the battery bank. This setting would be determined by the battery manufacturers guidelines. UPPER DELAY IN SECS: This is the delay setting for re-connecting the load to the power source. Delaying the re-connection allows the voltage at the power source to stabilise before the load is connected again. LOWER DELAY IN SECS: This is the delay, in seconds, before the power is disconnected from the light after the voltage reaches the LOWER LIMIT IN VOLTS. A delay here can be useful to prevent VSR chatter due to transient voltages and slight dips in power levels.

17 AUTOMATIC LOAD SWITCHING WIRING EXAMPLE FLOAT SWITCH LOAD 150A MAX

18 CONVENTIONAL HEAVY DUTY RELAY The MPVSR can be used as a conventional heavy duty relay for switching loads up to 150Amps continuous current at 12VDC. The control device is wired in series with the control wires and activated as required. The voltage settings should be programmed out of any range that would affect operation. Also, the relay can be set to either normally closed or normally open depending on requirements. CONVENTIONAL HEAVY DUTY RELAY WIRING EXAMPLE CONTROL SWITCH LOAD 150A MAX

19 SPECIFICATIONS Part Number Application Voltage Operating Voltage MA Volt DC and 24 Volt DC Sensing: 9V DC Minimum, 38V DC Maximum Switching: 33V DC Maximum Continuous Contact Rating Momentary Contact Rating Contact State Environmental protection Electrical Protection Standby Current Draw Standby Current Draw Operating Temperature Alarm Output Signal 150 Amps Maximum (rated at 40 o C) 500 Amps DC for a period of 10 seconds at 10% duty cycle (rated at 40 o C) User selectable normally open or closed To IP66 Thermal overload shutdown 10mA at 13.5V DC and 23mA at 27.0V DC 35mA at 13.5V DC and 55mA at 27.0V DC Ideally -25 o C to +50 o C Equal to input voltage to 200mA maximum Operating Humidity Ideally should not exceed 95% Enclosure Housing E-coated A360 (ADC 3) die cast aluminium Enclosure Cover and Injection moulded electrical grade ABS/PC Terminal Protector Load Terminals Control Terminals Dimensions Weight Tin plated copper stud Tin plated brass contact 135mm L x 85mm W x 65mm H 0.55kg

20 DIMENSIONS H 65mm L 135mm W 85mm

21 Matson Group - Warranty Against Defects Procedure Matson Group Pty Ltd 100 Links Rd, St Marys, NSW 2760 Phone: sales@matson.com.au Warranty Matson warrants its products to be free of defects for reasonable consumer use for a period of 12 months. Matson will repair or replace the warranted product and it will return the repaired products under warranty to the consumer at Matson s cost. To make a claim under this warranty, the consumer must: advise Matson of the defect as soon as it becomes apparent within 12 months of the purchase date and obtain a return authority by phoning Matson on the above number. provide satisfactory proof of purchase; and send the faulty item to the address supplied above. Exclusions from Warranty This warranty does not apply to products where: there is evidence of Improper maintenance or abuse to the products; the products have been exposed to harsh environmental conditions or those outside the specified operating conditions; Unauthorised modification is evident to the products or misuse of products; Operation outside the products specification. Warranty Disclaimers Matson s liability in respect of a breach of a consumer guarantee or any warranty made under these warranty terms and conditions for any products not of a kind ordinarily acquired for personal, domestic or household use is limited, in relation to the products to the extent

22 permissible by law and at it s option to: replacing the products or the supply of equivalent goods; the repair of the products; the payment of the cost of replacing the products or of acquiring equivalent goods; or the payment of the cost of having the products repaired. To the extent permitted by law, all other warranties whether implied or otherwise, not set out in these warranty terms and conditions are excluded and we are not liable in contract, tort (including, without limitation, negligence or breach of statutory duty) or otherwise to compensate the customer for: any increased costs or expenses; any loss of profit, revenue, business, contracts or anticipated savings; any loss or expense resulting from a claim by a third party; or any special, indirect or consequential loss or damage of any nature whatsoever caused by Matson s failure in complying with its obligations. MATSON IS NOT RESPONSIBLE FOR DAMAGE THAT OCCURS AS A RESULT OF YOUR FAILURE TO FOLLOW THE INSTRUCTIONS INTENDED FOR THE MATSON PRODUCT In the following paragraph, Our means Matson and You means the customer: Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. The benefits given to the customer in this warranty are in addition to other rights and remedies under a law in relation to the products to which this warranty applies.

23 Warranty Card (To be detatched and returned with the unit to the below address) Name: Company Name: Address: Ph: Fax: Purchased From: Date Purchased: Product Purchased (Model No.): This product is supplied with a 5 Year Warranty from date of purchase. Please Note: Should you experience any warranty related issues with this charger please call Matson Warranty Department on (02) between the hours of 8am - 4:00pm Monday - Friday. Our Warranty Department will issue instructions so please contact them before returning the charger. Proof of Purchase will be required for all warranty claims. The Matson Group Pty Ltd 100 Links Road St Marys NSW 2760 Australia Ph: (02) Fax: (02) sales@matson.com.au

24

JUMP STARTER OPERATOR S MANUAL RA1900

JUMP STARTER OPERATOR S MANUAL RA1900 JUMP STARTER OPERATOR S MANUAL RA1900 SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions for the RA1700 jump start. Read through this owner s manual carefully before

More information

OWNER S MANUAL MiniBoost

OWNER S MANUAL MiniBoost A Brand OWNER S MANUAL MiniBoost www.teambmpro.com CONTENTS Safety Precautions 3 About the MiniBoost 4 Installation 4 Personnel 4 Ventilation, Orientation, and Thermal Considerations 4 Mounting 5 Wiring

More information

Matson Jump Starter Operator s Manual

Matson Jump Starter Operator s Manual Matson Jump Starter Operator s Manual RA3800 SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions for the RA3800 Jumpstart. Read through this owner s manual carefully

More information

RU BMS Power Supply and Battery Management System Owners Guide

RU BMS Power Supply and Battery Management System Owners Guide RU2-4012- BMS Power Supply and Battery Management System Owners Guide (These instructions are intended for use by a technician familiar with electronic products) RU2-4012- BMS is a continuous duty power

More information

HE1U 1248 BMS High Efficiency 1U AC to DC Power Supply Owners Guide SPECIFICATIONS

HE1U 1248 BMS High Efficiency 1U AC to DC Power Supply Owners Guide SPECIFICATIONS HE1U 1248 BMS High Efficiency 1U AC to DC Power Supply Owners Guide (These instructions are intended for use by a technician familiar with electronic products) Integrated Smart Charger Integrated Low Voltage

More information

OWNER S MANUAL Please read this manual before operating your power supply

OWNER S MANUAL Please read this manual before operating your power supply AC-DC POWER SUPPLY Switch Mode AC-DC Power Supply Model No. PSU-1210 PSU-1223 PSU-1230 OWNER S MANUAL Please read this manual before operating your power supply Table of Contents Precautions 2 Description

More information

1000mA - 650mA Phase Dimmable LED Driver

1000mA - 650mA Phase Dimmable LED Driver Installation Guide DGLC1000C25PD 1000mA - 650mA Phase Dimmable LED Driver PATENT PENDING REGISTERED DESIGN Designed in Australia to meet Australian Standards and installation conditions DIGINET.NET.AU

More information

DALI 650mA LED Driver

DALI 650mA LED Driver Installation Guide DGLC650C18DD PATENT PENDING REGISTERED DESIGN Designed in Australia to meet Australian Standards and installation conditions DIGINET.NET.AU Diginet Control Systems Pty Ltd ABN 89 095

More information

CONGRATULATIONS ON THE PURCHASE OF YOUR THUNDER BAR DRIVING LIGHT

CONGRATULATIONS ON THE PURCHASE OF YOUR THUNDER BAR DRIVING LIGHT CONGRATULATIONS ON THE PURCHASE OF YOUR THUNDER BAR DRIVING LIGHT For your personal safety read, understand and follow the information provided in this instruction manual. 1 FEATURES High output 3W Cree

More information

DC to DC Step Up Converter Model: VTC305

DC to DC Step Up Converter Model: VTC305 DC to DC Step Up Converter Model: VTC305 Owner's Manual Please read this manual before operating your converter INTRODUCTION Step up a 12 VDC battery to between 13.5 and 17.0 or 24.0 and 27.5 VDC in 0.5

More information

AL-KO ESC USER MANUAL

AL-KO ESC USER MANUAL Vehicle Technology QUALITY FOR LIFE AL-KO ESC USER MANUAL OPERATING INSTRUCTIONS WARRANTY DETAIL About AL-KO ESC The new AL-KO ESC (Electronic Stability Control) is a sway and swerve stability control

More information

MA20DC MA20DCS 20 AMP, DC TO DC BATTERY CHARGER 20 AMP, DC TO DC BATTERY CHARGER WITH SOLAR INPUT

MA20DC MA20DCS 20 AMP, DC TO DC BATTERY CHARGER 20 AMP, DC TO DC BATTERY CHARGER WITH SOLAR INPUT MA20DC 20 AMP, DC TO DC BATTERY CHARGER MA20DCS 20 AMP, DC TO DC BATTERY CHARGER WITH SOLAR INPUT FEATURES Matson MA20DC and MA20DCS Designed to boost the low voltage found at the end of long cable lengths

More information

CONGRATULATIONS ON YOUR PURCHASE OF YOUR THUNDER BATTERY CHARGER! For your personal safety read, understand and follow the information provided in

CONGRATULATIONS ON YOUR PURCHASE OF YOUR THUNDER BATTERY CHARGER! For your personal safety read, understand and follow the information provided in CONGRATULATIONS ON YOUR PURCHASE OF YOUR THUNDER BATTERY CHARGER! For your personal safety read, understand and follow the information provided in this instruction manual & on the battery charger. This

More information

Smart By Design Flexible By Nature

Smart By Design Flexible By Nature Smart By Design Flexible By Nature A Suction System With Serious Smarts The Cattani Turbo SMART is the most powerful semi-wet suction system of its kind*. It s also the smartest. Its variable speed drive

More information

650mA Phase Dimmable LED Driver

650mA Phase Dimmable LED Driver Installation Guide DGLC650C18PD PATENT PENDING REGISTERED DESIGN Designed in Australia to meet Australian Standards and installation conditions DIGINET.NET.AU Diginet Control Systems Pty Ltd ABN 89 095

More information

SBC V In-Car Charger Dual Input (Solar MPPT & DC)

SBC V In-Car Charger Dual Input (Solar MPPT & DC) SBC-5926 12V In-Car Charger Dual Input (Solar MPPT & DC) Operation manual Keep this manual in a safe place for quick reference at all times. This manual contains important safety and operation instructions

More information

Smart Battery Charger GPC-35-MAX GPC-45-MAX GPC-55-MAX GPC-75-MAX GPC-100-MAX. Owner s Manual

Smart Battery Charger GPC-35-MAX GPC-45-MAX GPC-55-MAX GPC-75-MAX GPC-100-MAX. Owner s Manual Smart Battery Charger GPC-35-MAX GPC-45-MAX GPC-55-MAX GPC-75-MAX GPC-100-MAX Owner s Manual Table of Contents Important Safety Instructions 2 Features 3 Installation Guidelines 5 Warranty 8 1.0 Important

More information

GBC Polar A4 & A3 Laminators. Instruction Manual

GBC Polar A4 & A3 Laminators. Instruction Manual GBC Polar A4 & A3 Laminators Instruction Manual 2 Technical specifications Maximum Pouch Width Maximum Pouch Thickness Warm Up Time (2x75mic) Speed GBC A4 POLAR 241mm 2x125mic (250 Total) 5 mins 240 mm/min

More information

CONGRATULATIONS ON THE PURCHASE OF YOUR THUNDER DC TO DC BATTERY CHARGER.

CONGRATULATIONS ON THE PURCHASE OF YOUR THUNDER DC TO DC BATTERY CHARGER. CONGRATULATIONS ON THE PURCHASE OF YOUR THUNDER DC TO DC BATTERY CHARGER. For your personal safety, read, understand and follow the information provided in this instruction manual and on the battery charger.

More information

Installation and Operating Instructions for Davey HM Series Pressure Systems with Pressure Switch

Installation and Operating Instructions for Davey HM Series Pressure Systems with Pressure Switch Davey Repair or Replacement Guarantee In the unlikely event in Australia or New Zealand that this Davey product develops any malfunction within two years of the date of original purchase due to faulty

More information

"Buyer" or "you" means the person, firm or corporation to whom the order is addressed.

Buyer or you means the person, firm or corporation to whom the order is addressed. 1. Definitions "Australian Consumer Law" means the Australian Consumer Law set out in Schedule 2 to the Competition and Consumer Act 2010 (Cth) as given effect under Part XI of the Competition and Consumer

More information

OWNER S OPERATING MANUAL

OWNER S OPERATING MANUAL OWNER S OPERATING MANUAL WELD AND CUT ARC/TIG INVERTER PLASMA 30 PLASMA CUTTER TABLE OF CONTENTS Safety instructions 3-4 Weld & Cut ARC/TIG and Plasma Cutter 5 Page Installation 6 Welder Information 6-8

More information

230VAC Power Inverter 400W Owner s Manual

230VAC Power Inverter 400W Owner s Manual 400W 230VAC Power Inverter 400W Owner s Manual For safe and optimum performance, the Enerdrive epower Inverter must be used properly. Carefully read and follow all instructions and guidelines in this manual

More information

MB A 12V/24V DC PROGRAMMABLE DUAL BATTERY ISOLATOR

MB A 12V/24V DC PROGRAMMABLE DUAL BATTERY ISOLATOR MB-3688 120A 12V/24V DC PROGRAMMABLE DUAL BATTERY ISOLATOR User Manual Warning and Precautions MB-3688 is built with corrosion resistant material and the main electronic assembly is well sealed inside

More information

250W Folding Solar Panel USER MANUAL PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE USE.

250W Folding Solar Panel USER MANUAL PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE USE. 250W Folding Solar Panel.. USER MANUAL PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE USE. WARNINGS & SAFETY INFORMATION Keep the solar panel and controller away from liquids at all times. Keep

More information

OWNER S OPERATING MANUAL

OWNER S OPERATING MANUAL OWNER S OPERATING MANUAL ARC 140 AMP WELDER TABLE OF CONTENTS Page Safety instructions 3-4 Inverter Arc Welder 5 Welder Information 5 Arc 140 AMP welder set up 6 Assembly instructions 6 Operation 7 Welding

More information

Manual Installation & Operation

Manual Installation & Operation Manual Installation & Operation Model: NCxxLxx 12A or 30A Solid State Solar Charging Regulator and 12A Load Controller. 231 Patent #: 5,642,030 Applies Page 1 Warnings When Installing, connect grounds,

More information

VERSION 2017 V.1.0

VERSION 2017 V.1.0 1 2 3 VERSION 2017 V.1.0 1300 278 283 BEFORE USING THIS PRODUCT, PLEASE READ THESE INSTRUCTIONS OF USE CAREFULLY AND MAKE YOURSELF FULLY FAMILIAR WITH THE SYSTEM. PLEASE KEEP THESE INSTRUCTIONS IN A SAFE

More information

Digital echo-charge. Owner s Manual. Xantrex Digital echo-charge Battery Charger

Digital echo-charge. Owner s Manual. Xantrex Digital echo-charge Battery Charger Digital echo-charge Owner s Manual Xantrex Digital echo-charge Battery Charger INTRODUCTION The Xantrex Digital echo-charge is specially developed for charging an auxiliary battery with Freedom TM or Fleet

More information

Installation & Operators Manual

Installation & Operators Manual Installation & Operators Manual Model Serial Number Purchase Date 2007-2008 SegVator, LLC Patent Pending All Rights Reserved Important Safety Information Make sure the vehicle has a properly installed

More information

MANUAL D250SA SMARTPASS 120. Input Solar panel Earth Connection

MANUAL D250SA SMARTPASS 120. Input Solar panel Earth Connection MANUAL CONGRATULATIONS on the purchase of your new CTEK charger providing professional battery care. This charger is included in a series of professional chargers from CTEK SWEDEN AB and represents the

More information

USER S MANUAL GPC SERIES LOW VOLTAGE DISCONNECT. Galley Power LLC.

USER S MANUAL GPC SERIES LOW VOLTAGE DISCONNECT. Galley Power LLC. USER S MANUAL GPC SERIES LOW VOLTAGE DISCONNECT Galley Power LLC www.galleypower.com Table of Contents Safety Notice... 3 Disclaimer... 3 Safety Instructions... 4 1. Introduction... 5 1.1 Features and

More information

C3 Operating Instructions

C3 Operating Instructions Version 3.1 Stand 09.2014 Robert Bosch (Australia) Pty. Ltd. 1555 Centre Road Clayton, Victoria 3168 C3 Operating Instructions For further information please contact Bosch at: Australia 1300 30 70 40 www.boschautoparts.com.au

More information

12/24 VOLT AUTOMATIC SOLAR CHARGE CONTROLLER

12/24 VOLT AUTOMATIC SOLAR CHARGE CONTROLLER 12/24 VOLT AUTOMATIC SOLAR CHARGE CONTROLLER P/No.s SC320 & SC330 WARNING Please read these instructions completely prior to installation. Lead acid batteries can be dangerous. Ensure no sparks or flames

More information

Instruction Manual. Instruction Manual LIFETIME PLU Manufactured and packaged for SRGS PTY LTD ABN CONDITIONAL

Instruction Manual. Instruction Manual LIFETIME PLU Manufactured and packaged for SRGS PTY LTD ABN CONDITIONAL 12V 3300mAh MINI JUMP START 12V 3300mAh MINI JUMP START Instruction Manual Instruction Manual LIFETIME Manufactured and packaged for SRGS PTY LTD ABN 23 113 230 050 751and Gympie Road, Queensland 4501,

More information

Power InverterTM Watt. Continuous. User's Manual. WAGAN Corp. Limited Warranty Registration Form. Item no

Power InverterTM Watt. Continuous. User's Manual. WAGAN Corp. Limited Warranty Registration Form. Item no WAGAN Corp. Limited Warranty Registration Form All WAGAN Corporation products are warranted to the original purchaser of this product. Warranty Duration: This product is warranted to the original purchaser

More information

IV. PROOF OF PURCHASE: A warranty claim must be accompanied by proof of the date of purchase.

IV. PROOF OF PURCHASE: A warranty claim must be accompanied by proof of the date of purchase. PD9100 / 9200 SERIES POWER CONVERTER OWNERS MANUAL PROGRESSIVE DYNAMICS, INC. POWER CONVERTER LIMITED WARRANTY I. LIMITED WARRANTY: Progressive Dynamics, Inc. warrants its power converter to be free from

More information

SPI SS SPI SS Owners Manual

SPI SS SPI SS Owners Manual SELECTRONIC AUSTRALIA SPI 200-12SS SPI 200-24SS Owners Manual Selectronic Australia Pty Ltd. 25 Holloway Drive, Bayswater, Victoria, 3153 Rev 1 SELECTRONIC AUSTRALIA SPI 200-12SS, SPI 200-24SS OWNERS MANUAL

More information

INSTALLATION AND OPERATING INSTRUCTIONS

INSTALLATION AND OPERATING INSTRUCTIONS INSTALLATION AND OPERATING INSTRUCTIONS CS Series Pressed Stainless Steel Centrifugal Pump Please pass these instructions on to the operator of this equipment. Introduction Davey CS centrifugal pumps

More information

12/24V 30A AUTOMATIC/MANUAL WORKSHOP BATTERY CHARGER

12/24V 30A AUTOMATIC/MANUAL WORKSHOP BATTERY CHARGER 12/24V 30A AUTOMATIC/MANUAL WORKSHOP BATTERY CHARGER P/No. HDBC45 IMPORTANT SAFETY INFORMATION Please read this manual thoroughly before use and store in a safe place for future reference. WARNING Explosive

More information

12V 160A/24V 185A MANUAL WORKSHOP BATTERY CHARGER

12V 160A/24V 185A MANUAL WORKSHOP BATTERY CHARGER 12V 160A/24V 185A MANUAL WORKSHOP BATTERY CHARGER P/No. HDBC200 IMPORTANT SAFETY INFORMATION Please read this manual thoroughly before use and store in a safe place for future reference. WARNING Explosive

More information

160W Monocrystalline Folding Solar Panel USER MANUAL PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE USE.

160W Monocrystalline Folding Solar Panel USER MANUAL PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE USE. 160W Monocrystalline Folding Solar Panel.. USER MANUAL PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE USE. WARNINGS & SAFETY INFORMATION Keep the solar panel and controller away from liquids

More information

SUNC1200 / ITEM #40882 SUBMERSIBLE UTILITY PUMP OPERATIONS MANUAL

SUNC1200 / ITEM #40882 SUBMERSIBLE UTILITY PUMP OPERATIONS MANUAL SUNC1200 / ITEM #40882 SUBMERSIBLE UTILITY PUMP OPERATIONS MANUAL WWW.SUNRUNNERPOOL.COM Performance Model HP GPH of Water @ Total Feet Of Lift 0 ft. 5 ft. 10 ft. 15 ft. 20 ft. 25 ft. Max. Lift SUNC1200

More information

VADA - V60-J PRODUCT OVERVIEW CONSTRUCTION MOTOR USAGE LIMITATIONS WARRANTY

VADA - V60-J PRODUCT OVERVIEW CONSTRUCTION MOTOR USAGE LIMITATIONS WARRANTY PRODUCT OVERVIEW The VADA series of self priming jet pumps combine the functional benefits of centrifugal pumps and the practical and qualitative benefits of self-priming pumps. The Venturi system the

More information

VTC1000 Series Voltage Converter. Installation & Operation Manual

VTC1000 Series Voltage Converter. Installation & Operation Manual VTC1000 Series Voltage Converter Installation & Operation Manual INTRODUCTION All new Current Mode switching design offers increased power and reliability in a compact package. Extra input and output filtering

More information

REDI-LINE. Rugged, Reliable, DC to AC Power Conversion ELECTRIC GENERATORS USER'S GUIDE. KARAM A.L.

REDI-LINE. Rugged, Reliable, DC to AC Power Conversion ELECTRIC GENERATORS USER'S GUIDE. KARAM A.L. REDI-LINE ELECTRIC GENERATORS USER'S GUIDE Rugged, Reliable, DC to AC Power Conversion KARAM A.L. www.alternatorstarter.com 1-888-515-2726 REDI-LINE ELECTRIC GENERATOR MODEL INPUT ACTUAL OUTPUT ACTUAL

More information

Toll Free DX100. Owner's Guide. Printed in China

Toll Free DX100. Owner's Guide. Printed in China Toll Free 1 866 295 6775 www.powerbright.com DX100 Owner's Guide Printed in China 1 Introduction Thank you for purchasing thepowerbright DX100. Connected to the 12 volt outlet in your vehicle, the DX100

More information

OWNER S MANUAL SUBMERSIBLE UTILITY PUMP

OWNER S MANUAL SUBMERSIBLE UTILITY PUMP Model 51101-0 OWNER S MANUAL SUBMERSIBLE UTILITY PUMP Questions, problems, missing parts? Before returning to the store call AQUAPRO Customer Service 8 a.m. - 5 p.m., EST, Monday-Friday 1-844-242-2475

More information

Submersible Pump BIA-B10A BIA-B15A BIA-B25A BIA-B40A BIA-B42A BIA-B15VA BIA-B25VA BIA-B40VA BIA-B75A BIA-B75VA BIA-B75KA BIA-B120G

Submersible Pump BIA-B10A BIA-B15A BIA-B25A BIA-B40A BIA-B42A BIA-B15VA BIA-B25VA BIA-B40VA BIA-B75A BIA-B75VA BIA-B75KA BIA-B120G Submersible Pump BIA-B10A BIA-B15A BIA-B25A BIA-B40A BIA-B42A BIA-B15VA BIA-B25VA BIA-B40VA BIA-B75A BIA-B75VA BIA-B75KA BIA-B120G Installation & Operating Instructions BIANCO B range of submersible pumps

More information

4. TECHNICAL SPECIFICATIONS

4. TECHNICAL SPECIFICATIONS 1. SAFETY/WARNING 2. FIRST AID Before using the SCA solar maintenance battery chargers ensure the instructions have been read and understood. The SCA solar maintenance battery chargers are not intended

More information

CLEAN POWER TM CPS Series Operator s Manual

CLEAN POWER TM CPS Series Operator s Manual 12 Test Equipment CLEAN POWER TM CPS Series Operator s Manual Power Supply / Maintenance Charger for 12 Volt Systems The CPS series of power supplies / maintenance chargers are the ultimate in supplying

More information

Issue 3. Description: ROBINHOOD TAP PULL-OUT SERIES Model Numbers: TPO1200. Model may vary slightly from image pictured

Issue 3. Description: ROBINHOOD TAP PULL-OUT SERIES Model Numbers: TPO1200. Model may vary slightly from image pictured Issue 3 Description: ROBINHOOD TAP PULL-OUT SERIES 1 200 Model Numbers: TPO1200 Model may vary slightly from image pictured Overview Contents of packaging 1 x Robinhood Tap Pullout 1 x Installation kit

More information

EAGL 1-Touch Laser Level

EAGL 1-Touch Laser Level EAGL 1-Touch Laser Level Owner s Manual GENERAL INFORMATION Thank you for buying the EAGL 1-Touch laser. Although it is very simple to use, we recommend that you read this manual before operating the laser.

More information

INTELLI-CHARGE BATTERY CHARGER 12 VOLT, 7 STAGE SWITCHMODE

INTELLI-CHARGE BATTERY CHARGER 12 VOLT, 7 STAGE SWITCHMODE INTELLI-CHARGE BATTERY CHARGER 12 VOLT, 7 STAGE SWITCHMODE P/No.s IC700, IC700W, IC1000, IC1500 IMPORTANT SAFETY INFORMATION Please read this manual thoroughly before use and store in a safe place for

More information

INTELLI-POWER BATTERY CHARGER 12 VOLT, 7 STAGE SWITCHMODE. P/No.s IC700, IC700W, IC1000, IC1500

INTELLI-POWER BATTERY CHARGER 12 VOLT, 7 STAGE SWITCHMODE. P/No.s IC700, IC700W, IC1000, IC1500 INTELLI-POWER BATTERY CHARGER 12 VOLT, 7 STAGE SWITCHMODE P/No.s IC700, IC700W, IC1000, IC1500 IMPORTANT SAFETY INFORMATION Please read this manual thoroughly before use and store in a safe place for future

More information

Models DP10 & DP20 Series Low Voltage Disconnects User s Manual Rev. 1.1 October 31, 2007

Models DP10 & DP20 Series Low Voltage Disconnects User s Manual Rev. 1.1 October 31, 2007 B R A N D Models DP10 & DP20 Series Low Voltage Disconnects User s Manual Rev. 1.1 October 31, 2007 For Sales, Support and Service phone: 407-331-4793 fax: 407-331-4708 website: www.xenotronix.com email:

More information

VTC610 Series Voltage Converter. Installation & Operation Manual

VTC610 Series Voltage Converter. Installation & Operation Manual VTC610 Series Voltage Converter Installation & Operation Manual IMPORTANT SAFETY INSTRUCTIONS 1) SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions for this voltage

More information

IQS300 Series Quasi-Sine Inverter. Installation & Operation Manual

IQS300 Series Quasi-Sine Inverter. Installation & Operation Manual IQS300 Series Quasi-Sine Inverter Installation & Operation Manual INTRODUCTION State of the Art MOSFET technology coupled with unique Soft-Start circuitry guarantees reliable operation. The ON-OFF switch

More information

12 Volt 1500 Amp Intelli-Start LITHIUM JUMPSTARTER

12 Volt 1500 Amp Intelli-Start LITHIUM JUMPSTARTER 12 Volt 1500 Amp Intelli-Start LITHIUM JUMPSTARTER P/No. IS1500 IMPORTANT SAFETY INFORMATION Please read this manual thoroughly before use and store in a safe place for future reference. WARNINGS Do not

More information

The Power of Reliability INSTRUCTION MANUAL

The Power of Reliability INSTRUCTION MANUAL The Power of Reliability INSTRUCTION MANUAL SAFETY & WARNINGS Read this manual carefully and understand all Warnings and Cautions before connections are made to the Inverter. If unsure about any aspects

More information

Installation Instructions

Installation Instructions Installation Instructions Part #40120 Perfect Performance Products, LLC Painless Performance Products Division 2501 Ludelle Street Fort Worth, TX 76105-1036 800-423-9696 phone 817-244-4024 fax Web Site:

More information

DC TO AC PURE SINE POWER INVERTER PWRI18012S INSTRUCTION MANUAL

DC TO AC PURE SINE POWER INVERTER PWRI18012S INSTRUCTION MANUAL DC TO AC PURE SINE POWER INVERTER PWRI18012S INSTRUCTION MANUAL 1 A. INTRODUCTION The AIMS Power pure sine inverter product line is used for back-up power. The pure sine product line is ideal for sensitive

More information

Installation and Operating Instructions. MPPT Solar System Controller ISC3040

Installation and Operating Instructions. MPPT Solar System Controller ISC3040 Installation and Operating Instructions MPPT Solar System Controller ISC3040 ABOUT THIS MANUAL These operating instructions come with the product and should be kept with it as a reference to all user s

More information

600 Amp Battery Jumper with Air Compressor

600 Amp Battery Jumper with Air Compressor Item #2509 600 Amp Battery Jumper with Air Compressor User s manual- Read these instructions before using the unit Features Front LED Worklight Worklight Switch USB Power Ports and on/off Switch 12V DC

More information

VC-4820 Programmable DC-DC Converter with Battery Charger function USER'S MANUAL

VC-4820 Programmable DC-DC Converter with Battery Charger function USER'S MANUAL 1. INTRODUCTION VC-4820 Programmable DC-DC Converter with Battery Charger function USER'S MANUAL This MCU controlled Step Down DC-DC Converter has a digitally adjustable output in 0.2V increments. This

More information

ValveSentry USER S MANUAL PLEASE READ CAREFULLY AND SAVE

ValveSentry USER S MANUAL PLEASE READ CAREFULLY AND SAVE ValveSentry USER S MANUAL IMPORTANT! PLEASE READ CAREFULLY AND SAVE This user s manual contains important information about your ValveSentry device s operation. If you are installing this ValveSentry device

More information

10 Year Limited Warranty

10 Year Limited Warranty Power. On Your Terms. 10 Year Limited Warranty PHI 2.7 TM PHI 3.5 TM 60A SIMPLIPHI POWER, INC. REV020618 10 Year Limited Warranty: PHI 2.7 TM PHI 3.5 TM 60A 24V 48V Limited Pro-Rated Warranty Coverage

More information

OWNER S OPERATING MANUAL

OWNER S OPERATING MANUAL OWNER S OPERATING MANUAL MIG 100 GASLESS WELDER TABLE OF CONTENTS Page Safety instructions 3-4 MIG Welders 5 Welder Information 5 Gasless welder set up 6 Operation 6-10 Troubleshooting Guide 11-12 Spare

More information

TOWER MAXI T SINGLE CONVERSION ON LINE UPS SYSTEMS

TOWER MAXI T SINGLE CONVERSION ON LINE UPS SYSTEMS INSTRUCTION MANUAL TOWER MAXI T SINGLE CONVERSION ON LINE UPS SYSTEMS September 2000 TOWER UPS DISTRIBUTION (PTY) LTD 1 1. INTRODUCTION T A B L E O F C O N T E N T S 1.1 General Description... 3 1.2 Features...

More information

SUNC3000 / Item #40885

SUNC3000 / Item #40885 SUNC3000 / Item #40885 AUTOMATIC POOL COVER PUMP OPERATIONS MANUAL WWW.SUNRUNNERPOOL.COM 1 . Performance GPH of Water @ Total Feet Of Lift MODEL HP Max. Lift 0 ft. 5 ft. 10 ft. 15 ft. 20 ft. SUNC3000 1/3

More information

PROwatt 150 DC to AC Power Inverter. Owner s Guide

PROwatt 150 DC to AC Power Inverter. Owner s Guide PROwatt 150 DC to AC Power Inverter Owner s Guide About Xantrex Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with products from 50 watts mobile units to

More information

BATTERY METER SMART BATTERY GUAGE

BATTERY METER SMART BATTERY GUAGE BATTERY METER SMART BATTERY GUAGE P/No. BM320 IMPORTANT SAFETY INFORMATION Please read this instruction thoroughly before installing the product. WARNINGS Risk of explosive gas. Working in the vicinity

More information

PLATINUM SERIES. Haltech. High Power Igniter Module QUICK START GUIDE. 4 Channel - # HT Channel - # HT Channel - # HT020040

PLATINUM SERIES. Haltech. High Power Igniter Module QUICK START GUIDE. 4 Channel - # HT Channel - # HT Channel - # HT020040 PLATINUM SERIES Haltech High Power Igniter Module QUICK START GUIDE 4 Channel - # HT020032 6 Channel - # HT020036 8 Channel - # HT020040 HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL:

More information

HALLMARK INDUSTRIES INC

HALLMARK INDUSTRIES INC Performance Part No. HP. CONVERTIBLE JET PUMP USER S MANUAL GPH of Water @ Total Discharge Pressure of 40 psi Max. Pressure Max suction (shallow well) Max Suction (deep well) Max GPM (@0 head) Max Discharge

More information

Installation and Operating Instructions. Solar System Controller ISC3020

Installation and Operating Instructions. Solar System Controller ISC3020 Installation and Operating Instructions Solar System Controller ISC3020 ABOUT THIS MANUAL These operating instructions come with the product and should be kept with it as a reference to all user s of

More information

Installation and Operating Instructions. Solar System Controller ISC3030

Installation and Operating Instructions. Solar System Controller ISC3030 Installation and Operating Instructions Solar System Controller ISC3030 ABOUT THIS MANUAL These operating instructions come with the product and should be kept with it as a reference to all user s of the

More information

This document describes:

This document describes: Thank you for purchasing this product from ERM. We appreciate your interest in our unique product line as we try to offer our customers an alternative to today s traditional products. This programmable

More information

OWNER S MANUAL SELF-PRIMING PORTABLE UTILITY PUMP

OWNER S MANUAL SELF-PRIMING PORTABLE UTILITY PUMP Model 54011-0 OWNER S MANUAL SELF-PRIMING PORTABLE UTILITY PUMP Questions, problems, missing parts? Before returning to the store call AQUAPRO Customer Service 8 a.m. - 5 p.m., EST, Monday-Friday 1-844-242-2475

More information

Installation and operating instructions. Solar charge controller 10 A / 15 A / 0 A / 30 A PHOTOVOLTAIK - PHOTOVOLTAICS - PHOTOVOLTAIQUE - FOTOVOLTAICA

Installation and operating instructions. Solar charge controller 10 A / 15 A / 0 A / 30 A PHOTOVOLTAIK - PHOTOVOLTAICS - PHOTOVOLTAIQUE - FOTOVOLTAICA PHOTOVOLTAIK - PHOTOVOLTAICS - PHOTOVOLTAIQUE - FOTOVOLTAICA Installation and operating instructions Solar charge controller 10 A / 15 A / 0 A / 30 A EN 74.86 08.4 1. About this manual These operating

More information

LEV/Wn Building A Connected World

LEV/Wn Building A Connected World LEV/Wn Building A Connected World PK-93370-10-00-2B Installing and Testing a GFCI Please read this leaflet completely before getting started. A CAUTION To prevent severe shock or electrocution always turn

More information

EXTRA WIDE STEEL ROLLATOR

EXTRA WIDE STEEL ROLLATOR EXTRA WIDE STEEL ROLLATOR Product Codes: LM3882WBL Blue LM3882WBU Burgundy Extra Wide steel Rollator liquid coated painted frame. Soft touch hand brakes with locking mechanism. PVC extra wide seat. 8"

More information

Atlas ESR. User Guide. Capacitance and Equivalent Series Resistance Meter. Model ESR60 (Enhanced)

Atlas ESR. User Guide. Capacitance and Equivalent Series Resistance Meter. Model ESR60 (Enhanced) Atlas ESR Capacitance and Equivalent Series Resistance Meter Model ESR60 (Enhanced) User Guide Peak Electronic Design Limited 2004/2008 In the interests of development, information in this guide is subject

More information

Installation & Operation Manual. Electrak 10 Series / Electromechanical Linear Actuator

Installation & Operation Manual. Electrak 10 Series / Electromechanical Linear Actuator www..com Installation & Operation Manual Electrak 10 Series / Electromechanical Linear Actuator INTRODUCTION Thomson has many years of experience designing and manufacturing linear actuators for a wide

More information

Inverter User Manual

Inverter User Manual Inverter User Manual -------------for standard model DC TO AC Power Inverter CONTENTS Safety First 1. Introduction 2. Installation Guidelines 3. Using the inverter 4. Troubleshooting 5. Specifications

More information

3500W Solar Battery Charger Maximum Power Point Tracker

3500W Solar Battery Charger Maximum Power Point Tracker Page 1 of 8 This revolutionary maximum power point tracker solar charger was designed using the technology that won GSL Electronics the prestigious EDN Innovation Awards 08 and 09 and the Greentech Consensus

More information

OPERATION MANUAL SUBMERSIBLE FOUNTAIN PUMP PM2 600LV PM2 900LV PM2 1500LV PM2 2400LV PM2 4500LV

OPERATION MANUAL SUBMERSIBLE FOUNTAIN PUMP PM2 600LV PM2 900LV PM2 1500LV PM2 2400LV PM2 4500LV OPERATION MANUAL SUBMERSIBLE FOUNTAIN PUMP 804752 - PM2 600LV 804753 - PM2 900LV 804754 - PM2 500LV 804755 - PM2 2400LV 804756 - PM2 4500LV . INSTRUCTION FOR USE Please read t he operating instructions

More information

DC TO AC POWER INVERTER PWRIC150012W INSTRUCTION MANUAL

DC TO AC POWER INVERTER PWRIC150012W INSTRUCTION MANUAL DC TO AC POWER INVERTER PWRIC150012W INSTRUCTION MANUAL SAVE THIS MANUAL You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts

More information

Pro Booster 802Li. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference.

Pro Booster 802Li. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate

More information

Part Number: DBDC10 / DBDC20 DC to DC Dual Battery Charger Manual

Part Number: DBDC10 / DBDC20 DC to DC Dual Battery Charger Manual Part Number: DBDC10 / DBDC20 DC to DC Dual Battery Charger Manual For your personal safety read, understand and follow the information provided in this instruction manual. Important Safety Instructions

More information

SUNTURA SOLAR TRACKER

SUNTURA SOLAR TRACKER WindyNation SUNTURA SOLAR TRACKER SOT-TRKS-NF User s Manual Page 1 of 10 WindyNation 08/09/2012 Table of Contents 1 Introduction... 3 1.1 Limited Warranty... 3 1.2 Restrictions... 3 1.3 Warranty Claims

More information

SUPER PUMP OUT SYSTEM

SUPER PUMP OUT SYSTEM Congratulations on your purchase of the SUPER PUMP OUT SYSTEM. This instruction/parts manual is a guide for operating and servicing your BLUELINE SUPER PUMP OUT SYSTEM. Proper operation and service are

More information

Installation and operating instructions. Solar charge controller MPPT 10 A / 20 A Z Z

Installation and operating instructions. Solar charge controller MPPT 10 A / 20 A Z Z Installation and operating instructions Solar charge controller MPPT 10 A / 20 A EN 1 Contents 1. About these instructions... 3 1.1 Applicability... 3 1.2 Users... 3 1.3 Description of symbols... 3 2.

More information

Power. On Your Terms.

Power. On Your Terms. Power. On Your Terms. 10 YEAR LIMITED WARRANTY PHI 1310 TM 1 SIMPLIPHI POWER, INC. REV102016 10 YEAR LIMITED WARRANTY: PHI 1310 TM LIMITED PRO-RATED WARRANTY COVERAGE The SimpliPhi Power PHI 1310 as supplied

More information

ELECTROMECANICA CORMAR PRODUCT GUIDE 2014 R2 ELECTRO MECANICA CORMAR

ELECTROMECANICA CORMAR PRODUCT GUIDE 2014 R2 ELECTRO MECANICA CORMAR ELECTROMECANICA CORMAR PRODUCT GUIDE 2014 R2 ELECTRO MECANICA CORMAR Introduction Introducing ELECTROMECANICA CORMAR For more than 45 years, Electromecánica Cormar S.A. has been dedicated to the development

More information

Fitting Instructions

Fitting Instructions Dual Battery Kit Fitting Instructions Fitting Instructions We recommend that the is installed by a licensed auto-electrician. WARNING: Like any addition to your 12v set-up, ensure you ve installed a fuse

More information

AC Irrigation and Propagation Controllers I Four Station, 5006-I and 5006-IP Six Station

AC Irrigation and Propagation Controllers I Four Station, 5006-I and 5006-IP Six Station AC Irrigation and Propagation Controllers 5004-I Four Station, 5006-I and 5006-IP Six Station I N S T R U C T I O N M A N U A L Table of contents Introduction 1 1. Specifications 1 2. Controller Mounting

More information

PLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 QUICK START GUIDE (HT & HT059980) Version 4

PLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 QUICK START GUIDE (HT & HT059980)   Version 4 PLATINUM Series CAN WIDEBAND CONTROLLER WBC 1 & WBC 2 (HT059970 & HT059980) QUICK START GUIDE HALTECH HEAD OFFICE: PH: +612 9729 0999 FAX: +612 9729 0900 EMAIL: sales@haltech.com HALTECH US OFFICE: PH:

More information

DUAL WIDEBAND AIR/FUEL RATIO GAUGE Product Numbers: GS-W702W_Dual, GS-C702W_Dual, GS-T702W_Dual

DUAL WIDEBAND AIR/FUEL RATIO GAUGE Product Numbers: GS-W702W_Dual, GS-C702W_Dual, GS-T702W_Dual Installation Instructions Tech Support: 856.768.8300 TechSupport@GlowShiftGauges.com DUAL WIDEBAND AIR/FUEL RATIO GAUGE Product Numbers: GS-W702W_Dual, GS-C702W_Dual, GS-T702W_Dual (1) Gauge (2) Controllers

More information

DIGIGAUGE P R E S S U R E D I S P L A Y S Y S T E M I N S T R U C T I O N M A N U A L

DIGIGAUGE P R E S S U R E D I S P L A Y S Y S T E M I N S T R U C T I O N M A N U A L DIGIGAUGE P R E S S U R E D I S P L A Y S Y S T E M I N S T R U C T I O N M A N U A L Thank you for purchasing DigiGauge by ZAETECH Disclaimer DigiGauge is for show and off road use only. By using this

More information

Item no Smart AC 200 USB. User s Manual

Item no Smart AC 200 USB. User s Manual R Item no. 2402 Smart AC 200 USB User s Manual Smart AC 200 Watt with USB by Wagan Tech User s Manual Read before using this equipment Thank you for purchasing Smart AC 200 Watt with USB by Wagan Tech.

More information