AC centrifugal fan - RadiCal

Transcription

1 RE5-RB6- ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone Fax Limited partnership Headquarters Mulfingen County court Stuttgart HR 59 General partner Elektrobau Mulfingen GmbH Headquarters Mulfingen County court Stuttgart HRB 59 Nominal data Type Motor RE5-RB6- ME7-EI Phase ~ ~ Nominal voltage VC Frequency Hz 5 6 Type of data definition ml ml Valid for approval / standard CE CE Speed min - 75 Power input W 5 9 Current draw..7 Motor capacitor µf 5 5 Capacitor voltage VDB 5 5 Capacitor standard P (CE) P (CE) Min. back pressure Pa Min. ambient temperature C -5-5 Max. ambient temperature C 7 55 Starting current.5. ml = Max. load me = Max. efficiency fa = Running at free air cs = Customer specs cu = Customer unit Subject to alterations Data according to ErP directive Installation category Efficiency category Static Variable speed drive No Specific ratio *. * Specific ratio = + p fs / Pa ctual Request Request 5 Overall efficiency η es % 5 5 Efficiency grade N Power input P e kw. ir flow q v m³/h 9 Pressure increase p fs Pa 9 Speed n min Data definition with optimum efficiency. LU-85 The ErP data is determined using a motor-impeller combination in a standardised measurement configuration. Item no Revision 859 Release -5-8 Page / 5 ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 () Fax +9 () info@de.ebmpapst.com

2 RE5-RB6- Technical features Mass Size Surface of rotor Material of impeller Number of blades 7 Direction of rotation kg 5 mm Coated in black P plastic Clockwise, seen on rotor Type of protection IP ; Depending on installation and position as per EN 6-5 Insulation class "F" Humidity class F- Max. permissible ambient motor temp. (transp./ storage) Min. permissible ambient motor temp. (transp./storage) Mounting position Condensate discharge holes Operation mode Motor bearing Touch current acc. IEC 699 (measuring network Fig., TN system) Motor protection Cable exit Protection class Product conforming to standard pproval + 8 C - C Shaft horizontal or rotor on bottom; rotor on top on request Rotor-side S Ball bearing <.75 m Thermal overload protector (TOP) wired internally Variable I (if protective earth is connected by customer) EN 65-; CE CCC; EC Item no Revision 859 Release -5-8 Page / 5 ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 () Fax +9 () info@de.ebmpapst.com

3 RE5-RB6- Product drawing ccessory part: Inlet nozzle , not included in the standard scope of delivery Depth of screw max. mm Connection line silicone G.5 mm², x brass lead tips crimped Connection screen U blue Z brown U black PE green/yellow Item no Revision 859 Release -5-8 Page / 5 ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 () Fax +9 () info@de.ebmpapst.com

4 RE5-RB6- Charts: ir flow 5 Hz Druck p f s[pa]für Rho=,kg/m^ qv[cfm] qv[m^/h] ,9,8,7,6,5,,,,,9,8,7,6,5,,,,,9,8,7,6,5,,,, pfs_e[in HO] ir performance measured as per ISO 58 Installation category. For detailed information on the measuring set-up, please contact ebm-papst. Suction-side noise levels: Lw measured as per ISO 7 / Lp measured with m distance to fan axis. The values given are valid under the measuring conditions mentioned above and may vary according to the actual installation situation. With any deviation from the standard set-up, the specific values have to be checked and reviewed with the unit installed. Measured values U V f Hz n min P e W I Lp in Lw in qv m /h p fs Pa 55 U = Supply voltage f = Frequency n = Speed P e = Power input I = Current draw Lp in = Sound pressure level inlet side Lw in = Sound power level inlet side qv = ir flow p fs = Pressure increase Item no Revision 859 Release -5-8 Page / 5 ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 () Fax +9 () info@de.ebmpapst.com

5 RE5-RB6- Charts: ir flow 6 Hz Druck p f s[pa]für Rho=,kg/m^. qv[cfm] 6 8.,.5, ,8,6,,,8,6,, pfs_e[in HO] ir performance measured as per ISO 58 Installation category. For detailed information on the measuring set-up, please contact ebm-papst. Suction-side noise levels: Lw measured as per ISO 7 / Lp measured with m distance to fan axis. The values given are valid under the measuring conditions mentioned above and may vary according to the actual installation situation. With any deviation from the standard set-up, the specific values have to be checked and reviewed with the unit installed. 5,8,6 5,, 5,8 5,6, qv[m^/h]...6.8, Measured values U V f Hz n min P e W I Lp in Lw in qv m /h p fs Pa 5 7 U = Supply voltage f = Frequency n = Speed P e = Power input I = Current draw Lp in = Sound pressure level inlet side Lw in = Sound power level inlet side qv = ir flow p fs = Pressure increase Item no Revision 859 Release -5-8 Page 5 / 5 ebm-papst Mulfingen GmbH & Co. KG Bachmühle D-767 Mulfingen Phone +9 () Fax +9 () info@de.ebmpapst.com