MAX phantom 2000 / FAST

Transcription

1 SENSORS REQUIRED FOR CFORMS TO STD 325 CLASS I, II, III, IV CERTIFIED TO CAN/CSA STD C22.2 NO. 247 High Traffic Commercial Brushless DC Low Profile Swing Gate Operators Version 13 phantom 2000 / FAST Single or BiParting Gates BiParting Gates LY Installation and Owners Manual

2

3 Table of contents Phantom Specifications Important Safety Information 325 Model Classifications 325 Required ment Protection 325 Compliant Installation Requirements Intended Use of Swing Gate Operator Installation Gate Operator Position Recommended Gate Operator Layout Layout and Arm Height Dual Gate Operators Arm Position Options Arm Connection to Gate Optional Remote Supply Kit Magic Box Solar Optional Compact Installation LY Install Warning Signs ment Protection InGround Loops Wiring operator Gate Operator System Overview ment Protection Wiring Input AC Optional Remote Supply Kit Magic Box Solar Connection Optional Operators to 1 Optional Key Switch to Operator(s) Turn / Operator matrix 1 1 Overview Wiring Overview Primary Gate Open Left / Open Right Close Timer Selectable Gate Speed Control Battery BackUp Mode AntiTailgate Single Pass AntiTailgate Radio Receiver Radio Safety Pause Gate in Motion Alarms OBD Port Black Box Maglock Loop Detectors InGround Loop Connection Plug Gate Tamper ment LEDs Emergency Vehicle / Open Inputs Gate Disable Partial Open Alarm / Alarm Reset Button Gate Status Monitoring / / Connection CLOSG cell Connection Gate Operators Communication LEDs for 1 Battery in Use LED Motor Motion LEDs Adjustments Open and Close Limits Release Handle Clamp Reverse Sensor () Maintenance Qualified gate operator technician End user/home owner Phantom 2000 Wiring Schematics Manual Release Electronic Gate Open / Close Audible Alarm Replacement Parts List Warranty Phantom options / unique features Gate Tamper Feature 36 Amp/Hr Phantom Battery Module Optional Gate Disable Feature Event History Download imum Controls LLC. All rights reserved. No part of this manual may be reproduced in any means: graphics, electronics or mechanical, including photocopying without the expressed written permission of the publisher. Materials components and specifications are subject to change without notice. 1

4 max phantom specifications 325 Class of Operation Class I, II, III, IV Gate Type Vehicular Swing Gate Gate Weight / Length: Phantom ft or ft Phantom FAST 12 ft gate per operator NOTE: The Phantom FAST is LY available for installation on biparting gates (dual operators). A single gate operator CANNOT be used. 90 Opening Time: Phantom selectable speeds from approximately 11.5 sec to 20 sec depending on the weight and length of the gate. Phantom FAST 16 selectable speeds from approximately 6 sec to 14 sec depending on the weight and length of the dual gates. Cycles per Hour AC Input Continuous Battery BackUp Cycles (Batteries fully charged): BC7 Battery Module7 Amp/Hr Batteries, approximately 450 cycles BC36 Phantom Battery Module36 Amp/Hr Batteries, approximately 2000 cycles NOTE: The number of gate cycles using LY battery backup power will vary depending on the weight of the gate, the gate length, the operating condition of the gate hardware, temperature and the amount of charge the batteries have at the beginning of the battery power only operation. Input AC Switchable: 115VAC or 230VAC single phase Motor DC Brushless (equivalent to 1 HP AC motor) Operating Temperature: 4 F to 158 F (20 C to 70 C) ment Protection: 325 Type A Inherent ( sensor) Inputs for NORMALLY D (N.C.) 325 Type B1 (photo cell) and Type B2 (sensing edge) 12 5/ /4 14 5/8 important safety information WARNG To reduce the risk of injury or death: 1. READ AND FOLLOW ALL STRUCTIS. 2. Never let children operate or play with gate controls. Keep the remote control away from children. 3. Always keep people and objects away from the gate. NO E SHOD CROSS THE PATH OF THE MOVG. 4. Test the gate operator monthly. The gate MUST reverse on contact with a rigid object or stop when an object activates the noncontact sensors. After adjusting the force or the limit of travel, retest the gate operator. Failure to adjust and retest the gate operator properly can increase the risk of injury or death. 5. Use the emergency release only when the gate is not moving. 6. KEEP S PROPERLY MATAED. Read the owner s manual. Have a qualified service person make repairs to gate hardware. 7. The entrance is for vehicles only. Pedestrians must use separate entrance. 8. SAVE THESE STRUCTIS 2

5 ul 325 model classifications AUTHORIZED PERSNEL LY CLASS I Residential Vehicular Gate Operator A vehicular gate operator (opener or system) intended for use in a home of one to four single family dwellings, or a garage or parking area associated therewith. CLASS III Industrial/Limited Access Vehicular Gate Operator A vehicular gate operator (opener or system) intended for uses in an industrial location, loading dock area or other location not intended to service the general public. URITY CLASS II Commercial/General Access Vehicular Gate Operator A vehicular gate operator (opener or system) intended for use in a commercial location or building such as a multifamily housing unit (five or more single family units) hotel, garages, retail store or other building servicing the general public. CLASS IV Restricted Access Vehicular Gate Operator A vehicular gate operator (opener or system) intended for use in a guarded industrial location or buildings such as airport security area or other restricted access locations not servicing the general public, in which unauthorized access is prevented via supervision by security personnel. ul 325 required entrapment protection This vehicular gate operator must be installed with at least two independent entrapment protection means as specified in the table and definitions below. The same type of device shall not be used for both entrapment protection means. Use of a single device to cover both the opening and closing directions is in accordance with the requirement, however, a single device is not required to cover both directions. This operator has been provided with type A entrapment protection. The installer is required to install additional entrapment protection devices in each entrapment area. Gate Type Swing Gate Slide Gate Class I & II A, B1*, B2*, C, D A, B1*, B2*, D Class III & IV A, B1*, B2*, C, D, E A, B1*, B2*, D, E A Inherent entrapment protection system. B1 Provision for connection of a noncontact sensor (photoelectric sensor or the equivalent). B2 Provision for connection of a contact sensor (edge device or the equivalent). * B1 and B2 means of entrapment protection must be MITORED. C Inherent adjustable clutch or pressure relief device. D Provision for connection of an actuating device requiring continuous pressure to maintain opening or closing motion of the gate. E An audio alarm. 3

6 ul 325 compliant installation requirements A Install the gate operator only when: 1 The operator is appropriate for the construction of the gate and the usage Class of the gate, 2 All openings of a horizontal slide gate are guarded or screened from the bottom of the gate to a minimum of 6 feet (1.83 m) above the ground to prevent a 21/4 inch (57.2 mm) diameter sphere from passing through the openings anywhere in the gate, and in that portion of the adjacent fence that the gate covers in the open position, 3 All exposed pinch points are eliminated or guarded, and 4 Guarding is supplied for exposed rollers. B The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a separate access opening. The pedestrian access opening shall be designed to promote pedestrian usage. Locate the gate such that persons will not come in contact with the vehicular gate during the entire path of travel of the vehicular gate. C The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent structures when opening and closing to reduce the risk of entrapment. Swinging gates shall not open into public access areas. D The gate must be properly installed and work freely in both directions prior to the installation of the gate operator. Do not overtighten the operator clutch or pressure relief valve to compensate for a damaged gate. E For gate operators utilizing Type D protection: 1 The gate operator controls must be placed so that the user has full view of the gate area when the gate is moving, 2 A gate operator shall additionally be provided with a placard that is marked in letters at least 1/4in (6.4mm) high with the word WARNG and the following statement or the equivalent: Moving Gate Has Potential of Inflicting Injury or Death Do Not Start Gate Unless Path is Clear. 3 An automatic closing device (such as a timer, loop sensor, or similar device) shall not be employed, and 4 No other activation device shall be connected. F Controls intended for user activation must be located at least six feet (6 ) away from any moving part of the gate and where the user is prevented from reaching over, under, around or through the gate to operate the controls. Outdoor or easily accessible controls shall have a security feature to prevent unauthorized use. G The Stop and/or Reset button must be located in the lineofsight of the gate. Activation of the reset control shall not cause the operator to start. H A minimum of two (2) WARNG SIGNS shall be installed, one on each side of the gate where easily visible. I For gate operators utilizing a noncontact sensor: 1 See instructions on the placement of noncontact sensors for each Type of application, 2 Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle, trips the sensor while the gate is still moving, and 3 One or more noncontact sensors shall be located where the risk of entrapment or obstruction exists, such as the perimeter reachable by a moving gate or barrier. J For a gate operator utilizing a contact sensor: 1 One or more contact sensors shall be located where the risk of entrapment or obstruction exists, such as at the leading edge, trailing edge, and post mounted both inside and outside of a vehicular horizontal slide gate. 2 One or more contact sensors shall be located at the bottom edge of a vehicular vertical lift gate. 3 One or more contact sensors shall be located at the pinch point of a vehicular vertical pivot gate. 4 A hardwired contact sensor shall be located and its wiring arranged so that the communication between the sensor and the gate operator is not subjected to mechanical damage. 5 A wireless device such as one that transmits radio frequency (RF) signals to the gate operator for entrapment protection functions shall be located where the transmission of the signals are not obstructed or impeded by building structures natural landscaping or similar obstruction. A wireless device shall function under the intended enduse conditions. 6 One or more contact sensors shall be located on the inside and outside leading edge of a swing gate. Additionally, if the bottom edge of a swing gate is greater than 6 inches (152 mm) above the ground at any point in its arc of travel, one or more contact sensors shall be located on the bottom edge. 7 One or more contact sensors shall be located at the bottom edge of a vertical barrier (arm). 4

7 Pedestrians must use separate entrance. intended use of swing gate operator The operator is intended for use on a VEHICAR slide gate LY. It is intended to be used WITH appropriate entrapment protection safety devices and inground vehicle loop detection system. This operator has a inherent entrapment protection system and requires additional external monitored entrapment protection devices (Noncontact cells or contact sensing edges) for each entrapment area prior to gate operation. Opening Direction cell: Helps guard against the opening gate from entrapment. Opening/Closing Direction 10K Sensing Edge: Helps protect against entrapment in hinge area. Closing Direction cell: Helps protect the gate operator from accidentally closing on vehicles in the gate s closing path and entrapment. Warning Signs: Should be installed on both sides of gate area and easily visible. Moving Gate Can Cause Serious Injury or Death KEEP CLEAR! Gate may move at any time without prior warning. Do not let children operate the gate or play in the gate area. This entrance is for vehicles only. ment Area ment Area InGround Loops: Help protect the gate operator from accidentally opening and/or closing on vehicles in the gate s path. Opening/Closing Direction 10K Sensing Edge: Helps protect the gate operator from accidentally opening and/or closing on vehicles in the gate s path. (Wireless Option) Bottom of Gate Pedestrians MUST use a separate entrance. The gate operator IS NOT intended to be used on a PEDESTRIAN gate. NOTE: sensors MUST be MITORED and NORMALLY D (N.C.) 6 or More G/CLOSG direction Gate Protection 10K Sensing Edge on Bottom of Gate: If the bottom of gate is 6 inches or higher above the ground, then a sensing edge should be installed for safety. 5

8 AC AC FUSE 7 AMP FUSE 7 AMP PUTS PUTS Limit SW Limit SW PS24 SUPPLY PS24 SUPPLY installation Read and understand this entire manual before installation. Check with the local building department prior to installing this gate operator to comply with local building code requirements. The gate must be installed in a location so that enough clearance is supplied between the gate and adjacent structures when opening and closing to reduce the risk of entrapment. Swinging gates should not open into public access areas. Gate Operator position The gate must be properly installed and work freely in both directions prior to installation of the gate operator. Gate Bracket Pivot Point Closed Position A Hinge Pivot Point Illustrations not to scale Measurement Guidelines Longer A Should be at least 1/4 the gate length. than E NOTE: Uphill or heavy gates should be at least 1/3 gate length. B 15 minimum for open gate clearance (2 thick gate). C Distance A minus 17 inches (A 17 = C). D & E Arm should be 90 from gate when and in the straight locked position when D. imum arm length is 71 inches. Locked Position Arm Pivot Point Long Arm Short Arm D Open Position E Shorter than D 15 B /SOLAR TO CTROLLER Concrete Pad 24 x 24 C Operator Pivot Point Outside Property 2 Inside Property Hood /SOLAR TO CTROLLER DO NOT allow arm to touch hood in gate s position. TOO MUCH STRESS is put on the arm in this position during gate operation. 2 Gate Frame Preferred arm position is 90 from open gate. See page 10 for arm position options and connection to gate. 6

9 AC 115V F / Replace Battery Battery FUSE 7 AMP TEST Battery Battery Error D PUTS Limit SW installation recommended Gate Operator layout Support Bar Run wiring to OPERATOR. 10K Sensing Edge Mount on end of gate and hinge area. Run wiring to OPERATOR. i Sensing Edge Use for VEHICAR traffic LY. Pedestrians MUST use a separate entrance. Install appropriate entrapment protection safety devices for the G direction and CLOSG direction of gate cycling. Install inground and loops. Install a GROUNDG ROD within 10 ft of operator. An Optional loop can be installed if desired. PS24 SUPPLY NOTE: E ment protection sensor MUST installed or operator will NOT function. It MUST be MITORED and NORMALLY D (N.C.) 1/2 6 Above Ground WARNG WARNG connect chassis to ground rod for lightning protection Battery Voltage E 1/2 24 x 24 Pad /SOLAR TO CTROLLER BC7 Battery Module Illustration not to scale CLOSG cell Beam 21 High Support Bar CLOSG cell Ground Rod 8 x 17 Conduit Area G cell Beam Secure gate operator to concrete pad with four (4) 1/2 x 3 (min) sleeve anchors. From Safety Loop Center Loop 24 G cell CLOSG cell /RS485 (Required) & Optional Key Switch InGround Loops Beam Height Just Above Gate Operator Input AC (Required) Safety Loop Exit Loop (Optional) 7

10 installation Layout and arm height The gate must be properly installed and work freely in both directions prior to the installation of the gate operator. See Gate Operator Position on page 6 for operator position and Arm Connection to Gate on page 10. Conduit Guidelines and Suggestions (See page 7) REQUIRED AC input power wire to the OPERATOR. REQUIRED DC/RS485/Optional Key Switch wires from CTROL BOX to OPERATOR. REQUIRED ment protection (photocell and/or sensing edge) to the OPERATOR. See page 14. Normally Open photocells to the CTROL BOX. See page 14. Inground loop wires to the CTROL BOX. See page 15. Illustration not to scale Control Box Support Bar: See below Arm MUST be installed level. Secure gate operator to concrete pad with four (4) 1/2 x 3 (min) sleeve anchors. 1/ Above Ground Ground Level Optional Input Note: DC low voltage power wires can be run from a remote power supply ( Magic Box) to power the gate operator if desired. See page 11 for more information. Check local building codes in your area for depth of concrete before installation. Concrete Pad DC/RS485/ Key Switch Conduit Input Concrete Depth Note: The heavier the gate, the deeper the concrete pad should be. At least two feet recommended for heavier gate. Support Bar A support bar should be installed at the gate bracket height across the ENTIRE gate to keep the gate pickets from bending. Support Bar YES 19 Gate Bracket Support Bar Too High & Not Long Enough NO 8

11 AC FUSE 7 AMP PUTS Limit SW PS24 SUPPLY AC FUSE 7 AMP PUTS Limit SW PS24 SUPPLY dual Gate Operators installation The gates must be properly installed and work freely in both directions prior to the installation of the dual gate operators. See Gate Operator Position on page 6 for operator positions. Conduit Guidelines and Suggestions REQUIRED AC input power wire to EACH gate operator. REQUIRED DC/RS485/Optional Key Switch wires from operator to the CTROL BOX. Secure EACH gate REQUIRED RS485/Optional Key Switch wires from DARY operator to the CTROL BOX. operator to concrete REQUIRED ment protection (photocell and/or sensing edge) to EACH Corresponding OPERATOR. (see below & page 14) pad with four (4) Normally open photocell to the CTROL BOX. (page 14) 1/2 x 3 (min) sleeve anchors. Inground loop wires to the CTROL BOX. (page 15) Illustration not to scale 1/2 Control Box Secondary Arms MUST be installed level. Support Bars: See bottom of page 8. Primary 6 Above Ground Input Each entrapment protection sensor MUST be connected to corresponding gate operator. Illustrations not to scale Check local building codes in your area for depth of concrete before installation. RS485/Optional Key Switch to Control Box Concrete Depth Note: The heavier the gates, the deeper the concrete pads should be. At least two feet recommended for heavier gates. Dual Gates CLOSG direction ThruBeam cell LY: See separate wiring instruction sheet. Reflector ment Area G/CLOSG direction i Sensing Edge Outside Property 19 G/CLOSG direction Sensing Edges DC/RS485/ Key Switch Conduit Input Optional Input Note: DC low voltage power wires can be run from a remote power supply ( Magic Boxes) to power the gate operators if desired. See page 11 for more information. G/CLOSG direction i Sensing Edge To Input ment Area /SOLAR TO CTROLLER to Secondary Operator or Secondary Operator NO 1 to Secondary Operator or Inside Property to Primary Operator or Primary Operator 1 to Primary Operator or /SOLAR TO CTROLLER ment Area G direction cell See page 14 for installation instructions. See pages 1819 for wiring instructions. G direction cell 9

12 AC FUSE 7 AMP PUTS Limit SW PS24 SUPPLY AC FUSE 7 AMP PUTS Limit SW PS24 SUPPLY installation Gate in Opened Position arm position options RetroFit Arm Option When replacing an existing gate operator, the arm may not be able to conform to the preferred arm position (90 from gate in open position). The positions illustrated below can be acceptable as long as the gate operator cycles smoothly and there is NO gate hesitation when gate starts cycling in either direction. 90 Gate in Opened Position 90 High Traffic Arm Option Gates in Closed Position Arms are NOT installed in ED position. If a vehicle tries to push gates open, arms will give when NOT in the locked position and allow gates to move without damaging the gate operators. The tamper relay will be activated for a few seconds which will trigger a camera or alarm system if desired. arm connection to gate After you re satisfied testing the arm in the FL and FL D positions, weld gate bracket and arm. Illustrations not to scale Full Closed Locked Position /SOLAR /SOLAR TO CTROLLER TO CTROLLER Full Open Preferred arm position is 90 from open gate. weld completely around arm tubing and gate bracket. Release Handle Clamp ReAttach Arm to Operator: Limit pin MUST fit into slot in bottom of release handle clamp directly under the arm when reattaching arm to operator. Arm MUST be installed level. Arm Slot Limit Tabs Limit Pin Gate Bracket Assembly Arm Elbow Assembly 10

13 AC 115V FUSE 7 AMP /SOLAR F / Replace Battery Battery TO CTROLLER TEST Battery Battery Error D servicing unit FUSE 7 AMP PUTS Limit SW installation optional remote power supply kit max magic box A remote power supply is for installations where it is too costly or difficult to trench a 115/230 VAC power line to the operator but instead run a low voltage power line to the operator. A Magic Box Kit (sold separately) is required to remotely install the PS24 power supply. Install the Magic Box near the 115 VAC or 230 VAC input AC power source, up to 1000 ft away from gate operator. Remove PS24 power supply from gate operator and place in Magic Box. See page 21 for Magic Box wiring instructions. NOTE: A Magic Box kit is required for EACH gate operator when using dual gate operators. Control Box ( 1) Operator Magic Box Near Source Magic Box Kit Distance See table below 2Wires, DC Low Voltage PS24 SUPPLY At Magic Box PS24 Supply Removed from Operator 115/230 VAC Source /Solar In Connector WARNG connect chassis to ground rod for lightning protection Battery Voltage E 1/2 BC7 Battery Module PS24 SUPPLY Wire Nuts AC WARNG! HIGH VOLTAGE disconnect power before Select Input Voltage: 115VAC or 230VAC 230V warranty VOED if label is REMOVED Control Box ( 1) At Gate Operator DC/RS485/ Optional Key Switch Input Conduit not supplied Input AC To Operator 24 VDC Low Voltage DC Low Voltage Ground Level Conduit Gate Weight Wire Distance Wire Gauge 2000 lbs 500 ft 10AWG 1000 ft 8AWG Concrete Pad DC Low Voltage 11

14 Battery Voltage E 1/2 F Replace Battery Battery Phantom Battery Module TEST Battery Error TO CTROLLER installation solar Optional Refer to Solar application guide. OPTIAL BC36 Phantom Battery Module /SOLAR / BC36 Solar Panel 24 Volt /Solar In Connector Wire Nuts Solar Kit BC36 Phantom Battery Module (36 Amp/Hr) Battery This OPTIAL module replaces the BC7 Battery Module in the operator. It can be used when the operator is in a high traffic cycling area (Approximately 2000 cycles using only battery power). Sold separately. Solar Panel Electronics Box Solar Kit: MUST be used when using solar power. Sold separately. Solar Panel: must be mounted facing south. It must get full sunlight throughout the day, NO shadow obstructions. Solar Kit Operator Control Box Solar Panel Electronics Box 12

15 AC FUSE 7 AMP PUTS Limit SW PS24 SUPPLY AC FUSE 7 AMP PUTS Limit SW PS24 SUPPLY installation compact installation only Use compact installation arm measurements when area between the gate and wall is 20 min to 32. DO NOT use these arm measurements for a standard installation. (For standard installation, see page 6) Illustrations not to scale Open Position Gate Bracket Pivot Point 33 Hinge Pivot Point Illustrations not to scale Closed Position /SOLAR TO CTROLLER ment Area Wall Long Arm Short Arm Arm Elbow Pivot Point 25.5 Operator Pivot Point /SOLAR TO CTROLLER 24 Cut the standard arms down to meet the shorter measurements. 20 min to Cut Long Arm Cut Short Arm 20 Cut 4 It is necessary to protect against the entrapment that could occur with this type of installation. (See entrapment protection on page 13) install warning signs A minimum of two (2) WARNG SIGNS shall be installed, one on each side of the gate where easily visible. Moving Gate Can Cause Serious Injury or Death KEEP CLEAR! Gate may move at any time without prior warning. Do not let children operate the gate or play in the gate area. This entrance is for vehicles only. Pedestrians must use separate entrance. Moving Gate Can Cause Serious Injury or Death KEEP CLEAR! Gate may move at any time without prior warning. Do not let children operate the gate or play in the gate area. This entrance is for vehicles only. Pedestrians must use separate entrance. Moving Gate Can Cause Serious Injury or Death KEEP CLEAR! Gate may move at any time without prior warning. Do not let children operate the gate or play in the gate area. This entrance is for vehicles only. Pedestrians must use separate entrance. 13

16 entrapment protection Install photocells and/or sensing edges to help protect against entrapment during cycling of the gate (entrapment protection). E entrapment protection sensor MUST be installed and connected to CLOSG direction on motor controller or operator will NOT function. ment protection sensors MUST be MITORED and NORMALLY D (N.C.). Top View IMPORTANT: Sensing edges MUST be Monitored 10K Normally Closed Type and a GEM104 module MUST be installed. Beam: 5 or LESS from D gate. Wireless Module End of Gate Options Closed Gate installation ment Area WIRELESS NOTE: Refer to the instruction sheet that comes with the wireless module for wiring and mounting instructions when using wireless option. Closed Gate Hinge Area Closed Gate Conduit CLOSG direction photocell to input, Monitored. Normally D (N.C.) 10K i Sensing Edge (N.C.) ment Area G/CLOSG Two Sided 10K Sensing Edge to or input or input Dual Gate Operators NOTE: Run EACH entrapment protection sensor to each corresponding OPERATOR S motor controller. See page 9. Side View CLOSG LY One Sided 10K Sensing Edge input See pages 1819 for wiring instructions. Bottom of Gate Gate Open The hinge area may need protection against entrapment. 10K mini sensing edge works well in this area. (/ direction, or input) G/CLOSG or Closing LY 10K (N.C.) Sensing Edge IMPORTANT: cells MUST be in alignment or fault will occur. Normally D (N.C.) G direction cell IMPORTANT: cells MUST be Monitored Normally Closed Type. 6 or More CLOSG direction cell / Sensing Edge on Bottom of Gate: If the bottom of gate is 6 or higher above the ground, then a 10K sensing edge should be installed. Gate Open G direction cell, Install just above gate operator. Beam Height: 21 Normal IMPORTANT: cells MUST be in alignment or fault will occur. ment Protection Sensing Edge, Install along entire edge of gate. 14

17 DC M M LE 1.5Sec installation inground loops Install inground loops to help protect vehicles from a moving gate. See pages 27 & 31 for wiring instructions. Outside Property 4 ft Safety Loop 4 ft 4 ft Refer to loop maunufacturer s instructions to determine specific loop dimensions. It is recommended that a licenced installer perform this work. Illustration not to scale Inside Property Side View of Saw Cut 4 ft Run inground loops conduit to CTROL BOX. Control Box Sealant Backer Rod 1 1/2 Typical Center Loop Loop Wire Saw Cut 1/4 Saw Cut Pavement 4 ft Safety Loops Are placed on each side of the gate to prevent the gate from closing on a vehicle in it s path. They will stop or reverse the cycling of the gate while a vehicle is in or near the gate s pathway. Center Loop Will LY HOLD the gate in the Full Open Position when a vehicle is on the center loop. However, it WILL NOT stop or reverse the gate once it starts to close. Exit Loop Automatically opens the gate for exiting vehicles without having to use a radio transmitter (remote control). The exit loop can be placed a minimum of 4 feet away from the safety loop or far enough away from the gate so it has opened by the time the vehicle approaches it. Inside Property LOOP 4 ft Lead Wires LOOP LOOP Safety Loop 4 ft min. Exit Loop LOOP 4 ft Safety loops need to be wired in series. Outside Property Loop lead wires are twisted 6 twists per foot minimum inside conduit. 1 Wiring TAIL TIMER D AUTOMATIC / CTROLS POSITI RADIO SPEED MOTI LE NO / CLAMP SLIPPG DISABLE ALARM 12V Tamper USE 15

18 AC F D Wiring operator Check with local building department prior to installing any permanent wiring on this gate operator. Make sure all wiring complies with local code requirements. Gate Operator System Overview Gate Operator WARNG connect chassis to ground rod for lightning protection 115V Battery Voltage E 1/2 / Replace Battery Battery FUSE 7 AMP /SOLAR TEST Battery Battery Error 1 6 BC7 Battery Module TO CTROLLER 8 PS24 SUPPLY Limit SW PUTS PS24 Supply: AC power management for the AC input power to the gate operator. See pages 20, 21 & 25. Release Handle Clamp: Manually move the gate when handle is raised. See page 37. Audible Alarm: Sounds when there is a problem with cycling the gate. Push the alarm reset button on the control box to shut off alarm (see below). Alarm can sound every time operator is cycled using LY battery backup power when turned, See page 34. DC Brushless Motor (6 million cycles) : Manages entrapment protection devices and operator motor reversing sensitivity adjustment. See pages 17, 18, 19, 23, 24 & 27. BC7 Battery Module: Battery BackUp and DC power management for the gate operator. See page 17. Limit Tabs: Adjusts the and gate positions. See page 36. Limit Switch Box: Contains the limit switches. Gate operator will NOT function when limit switch box is not connected. See page 36. Control Box DC RADIO AUTOMATIC / CTROLS TAIL M TIMER A POSITI 1 TIME 1.5Sec 2Sec M MOTI SPEED NO / CLAMP SLIPPG LE LE Tamper ALARM 12V DISABLE USE A B C 1: Manages control panel operations. Manages inputs/outputs, loops and reports problems with gate operator. See 1 Section starting on page 24. Alarm Reset Button: Push to shut off alarm and/or reset 1. See pages 27, 34 & 40. Optional Electronic Gate Open/Close Key Switch: Electronically move the gate open or closed by turning removable key in the key switch if connected to operator(s). See pages 24 & 42. B C 16

19 Wiring operator Gate Operator System Overview continued BC7 Battery Module connect to before use IMPORTANT PWR RS485 RS485 1 PWR 12V 2 ALARM /SOLAR ment Protection Sensor Guidelines PUTS LY power entrapment protection sensors with PWR 12V PWR 12V MUST be used A sensor MUST be wired to or operator WILL NOT function. Wire NORMALLY D (N.C.) In MITORED sensors LY, to each operator s when dual operators are used. Reversing Edge and/or can be wired to ANY of the 3 Inputs. Monitored Reversing Edge PWR 12V MUST be used to power MITORED sensors UNUSED inputs MUST remain JUMPERED or fault will occur. 2 3 OR Monitored TO CTROLLER Battery Voltage E 1/2 F Inputs & MUST be LEARNED to MITOR sensors. To LEARN inputs & : CAUTI: See installation instructions. ATTENTI: Voir la notice d installation. 3 4 / Replace Battery Battery Continued on next 2 pages. O N P A B C 1. MITORED Sensors MUST be wired to inputs BEFORE they can be learned. Any unused inputs MUST be jumpered. 2. Reversing Edge and/or Ce l can be wired to either input 2 or Press and HOLD the & buttons at the same time on 1 until beep is heard, learn mode begins. MOTI TEST Battery Battery Error 2 3 unused inputs Limit SW BC7 Battery Module 7 Learn mode lasts for 5 min. indicated by beeping. 4. LEDs WILL be for each detected sensor on. LEDs WILL be for BOTH s when dual operators are used. 5. Press button again within 5 min. to learn sensors and end learn mode, beeping stops. Inputs are now MITORED. ment Protection Inputs: MUST jumper PUTS G LED: Gate operator is successfully communicating with 1 when lit. H Limit SW LED: Limit Switch Sensors are successfully communicating with when lit. I LED: sensor has been activated when lit. J LED: sensor has been activated when lit. LED will light up during LEARNG mode when sensor is connected, see page 19. K cell LED: cell sensor has been activated when lit. LED will light up during LEARNG mode when sensor is connected, see next page. L LED: Edge1/Edge2/cell inputs have been activated when lit. M LED: Low voltage power is connected when lit. N RS485 Input: Factory wired for Primary operator. Wire to 1 for Secondary operator LY. O Input: for 1 and wirless receiver for edge. P 12V ment Protection Sensor Out: 12V that ALL ment protection sensors MUST use PWR 12V power. DUAL OPERATORS NOTE: Connect EACH photocell/sensing edge to the corresponding gate operator. See page 9. D E F G J L H I K M 1 2 /SOLAR Port: PS24 Supply connection. 3 Battery Voltage LEDs: Show amount of battery power available. LEDs are always when using AC power. Test battery button must be pressed to show battery power when using battery power LY. 4 / Battery Button: IMPORTANT: Battery power automatically turns when PS24 Supply AC Switch is turned. 5 Replace Battery LED: Replace battery when lit. 6 TEST Battery Button: Press to show amount of battery power available when using battery power LY (Battery voltage LEDs will light respectively). 7 Battery Error LED: Lights when there is a battery connection problem. Make sure battery plug #1 is plugged into port or there is no damaged or loose wires. ment Protection Sensor Inputs Plug: MUST be plugged into port Before use. To turn ALL to operator: 1. Turn AC Switch on PS24 Supply. Battery power remains. 2. WAIT for 15 seconds. 3. Press and HOLD (approx. 5 seconds) the RED / button until BC7 LEDs turn, then release button. LEDs will turn. A LED: Excessive current being drawn by motor when lit. B LED: sensor has been activated when lit. C Knob: 16 selectable sensitivity settings of sensor. D LED: sensitivity reached when lit. E Jog / Buttons: Push and HOLD buttons accordingly to move the gate (release the button to stop gate). WARNG: Avoid moving gate while using Jog buttons. F PUTS: /RT inputs: Can connect to an External Open/Close Key switch. Connect a single key switch to control dual gate operators, See page 24. input: Low Voltage Common connection. MITORED CLOSG direction LY input: Connects to a NORMALLY D (N.C.) Sensing Edge or cell. Closing direction activation: gate will reverse to full open position and reset close timer. Opening direction activation: gate will NOT be monitored during opening cycle. LEARNED MITORED G/CLOSG direction input: Connects to a NORMALLY D (N.C.) Sensing Edge or cell. Input MUST be LEARNED before it can MITOR a connected sensor (see page 19). Closing direction activation: gate will REVERSE to full open position but will NOT reset close timer. Another command is required for gate to resume operation. Opening direction activation: gate will REVERSE 2 inches and. Another command is required for gate to resume operation. LEARNED MITORED G/CLOSG direction input: Connects to a NORMALLY D (N.C.) Sensing Edge or cell. Input MUST be LEARNED before it can MITOR a connected sensor (see page 19). Closing direction activation: gate will. Another command is required for gate to resume operation. Opening direction activation: gate will. Another command is required for gate to resume operation. 17

20 Wiring operator : MITORED LY : LEARNED MITORED / : LEARNED MITORED / PUTS Limit SW Typical Wiring For: Jumper UNUSED ment Protection Inputs or a fault will occur. Normally Closed (N.C.) Sensor Wire Example: Inputs 2 & 3 are NOT used and MUST be jumpered to. a 10K Normally Closed (N.C.) Sensing Edge... AND/OR... a Normally Closed (N.C.) One Sided Edge PWR 12V Polarity does NOT matter 10K Edge Normally Closed GEM 104 = Obstruction BLKG = Fault M. PWR PUT GEM104 PWR RS485 RS485 Closed Gate PWR 12V G/CLOSG Two Sided 10K Sensing Edge to or input (to wireless module when using Wireless Option). To Normally Closed 10K Sensing Edge To (Polarity does NOT matter) ALARM ment Protection Sensor Guidelines PUTS LY power entrapment protection sensors with PWR 12V PWR 12V MUST be used A sensor MUST be wired to or operator WILL NOT function. Wire NORMALLY D (N.C.) MITORED sensors LY, to each operator s when dual operators In Monitored Reversing Edge are used. be wired to ANY of the 3 Inputs. power MITORED sensors JUMPERED or fault will occur. Reversing Edge and/or can PWR 12V MUST be used to UNUSED inputs MUST remain End of Gate Options (C) (N.C.) CLOSG Direction LY 2 3 OR Inputs & MUST be LEARNED to MITOR sensors. To LEARN inputs & : Monitored CAUTI: See installation instructions. ATTENTI: Voir la notice d installation MITORED Sensors MUST be wired to inputs BEFORE they can be learned. Any unused inputs MUST be jumpered. 2. Reversing Edge and/or can be wired to either input 2 or Press and HOLD the & buttons at the same time on 1 until beep is heard, learn mode begins. MOTI Learn mode lasts for 5 min. indicated by beeping. 4. LEDs WILL be for each detected sensor on. LEDs WILL be for BOTH s when dual operators are used. 5. Press button again within 5 min. to learn sensors and end learn mode, beeping stops. Inputs are now MITORED. 1 ment Protection Inputs: MUST jumper 2 3 unused inputs Limit SW PUTS Closed Gate Wireless Module Gate Edge Module (GEM104) MUST be used with EACH Normally Closed 10K type Sensing Edge. 10K Edge Normally Closed GEM 104 = Obstruction BLKG = Fault M. PWR PUT IMPORTANT Sensing devices MUST be powered by or they will NOT be MITORED. To (C) To,, or PWR RS485 RS485 PWR 12V ALARM ment Protection Sensor Guidelines PUTS LY power entrapment protection sensors with PWR 12V PWR 12V MUST be used A sensor MUST be wired to or ment Area In Monitored Reversing Edge operator WILL NOT function. MITORED sensors LY, to each operator s when dual operators are used. be wired to ANY of the 3 Inputs. power MITORED sensors Wire NORMALLY D (N.C.) Reversing Edge and/or can PWR 12V MUST be used to UNUSED inputs MUST remain JUMPERED or fault will occur. 2 3 OR Inputs & MUST be LEARNED to MITOR sensors. To LEARN inputs & : Monitored CAUTI: See installation instructions. ATTENTI: Voir la notice d installation MITORED Sensors MUST be wired to inputs BEFORE they can be learned. Any unused inputs MUST be jumpered. 2. Reversing Edge and/or can be wired to either input 2 or Press and HOLD the & buttons at the same time on 1 until beep is heard, learn mode begins. MOTI Learn mode lasts for 5 min. indicated by beeping. 4. LEDs WILL be for each detected sensor on. LEDs WILL be for BOTH s when dual operators are used. 5. Press button again within 5 min. to learn sensors and end learn mode, beeping stops. Inputs are now MITORED. 1 ment Protection Inputs: MUST jumper 2 3 unused inputs Limit SW PUTS Gate Closed Wireless Option: See separate wiring instruction sheet. CLOSG LY One Sided 10K Sensing Edge to input (to wireless module when using Wireless Option). PWR 12V Polarity does NOT matter G/CLOSG 10K i Sensing Edge to or input Closed Gate NOTE: see next page for sensor model #s and Learning and inputs. To GEM104 To GEM104 Gate Open G/CLOSG or Closing LY 10K (N.C.) Sensing Edge (Hardwired) (C) 10K i Sensing Edge (N.C.) G direction cell Normally D (N.C.) IMPORTANT: cells MUST be in alignment or fault will occur. To or To (Polarity does NOT matter) DUAL OPERATORS NOTE: Connect EACH photocell/sensing edge to the corresponding gate operator. See page 9. Recr Trans ThruBeam See next page for a specific photocell s N.C. N.O. input. Reflective Beam ment Area To Reflector IMPORTANT: cells MUST be in alignment or fault will occur. Polarity does NOT matter To MC200 To To NORMALLY D CLOSG direction cell 18

21 DC DC M M M M LE LE 1.5Sec 1.5Sec Wiring operator PUTS Limit SW Inputs 2 & 3 MUST be LEARNED to MITOR G/CLOSG direction sensors. To LEARN inputs 2 & 3 : 1. MITORED Sensors MUST be wired to inputs BEFORE they can be learned. Any unused inputs MUST be jumpered. See previous page. 2. A Sensing Edge or can be wired to either input 2 or 3. Note: CLOSG direction LY. D AUTOMATIC / CTROLS 3. Press and HOLD the button & then the button together on 1 until beep is heard, learn mode begins. NOTE: DO NOT press the button before the button or learn mode will NOT function. MOTI RADIO TAIL TIMER POSITI SPEED MOTI NO / CLAMP SLIPPG LE DISABLE Tamper ALARM 12V USE 4. LEDs WILL be for each detected sensor on. LEDs WILL be for BOTH s when dual operators are used. If an LED is not on and it should be, wiring to sensor is bad, photocells are out of alignment, photocells are wired wrong N.C. or N.O. depending on which Limit SW ht PUTS photocells are used (see below) or sensor is bad etc. and must be corrected. When all LEDs are that should be, proceed to next step. Example shows that sensors are DETECTED on inputs and. D AUTOMATIC / CTROLS 5. Press button again within 5 min. to learn sensors and end learn mode, beeping stops. Wired Inputs are now MITORED. If button is not pressed within 5 min. learn mode terminates. If no sensors are detected then factory default setting ( and are NOT Monitored) is restored. MOTI RADIO TAIL TIMER POSITI SPEED MOTI NO / CLAMP SLIPPG LE DISABLE ALARM 12V Tamper USE Compliant MITORED Normally Closed ment Protection Devices: Normally Closed Definition: When is off, relay contacts are. When is on, relay contacts are D. s: Model RG Miller Edge ReflectiGUARD ReflectiveBeam Type (Normally Closed) Model PG Miller Edge PrimeGUARD ThruBeam Type with battery operated transmitter (Normally Closed) Model EMXIRBM EMX ThruBeam Type (Normally Closed) Model EMXIRBRET EMX ReflectiveBeam Type (MUST be wired to Normally Open) Model E3KR10K4NR OMR Electric Sensor ReflectiveBeam Type (MUST be wired to Normally Open) will work with 12V Model Allen Bradley ReflectiveBeam Type (MUST be wired to Normally Open) Directwired 10K Sensing Edge: Model 10K Sensing Edge with GEM104 Module Miller Edge (Normally Closed) 10K i Edge imum Controls (Normally Closed) Requires a Miller Edge GEM104 module 10K imum Controls (Normally Closed) Requires a Miller Edge GEM104 module Sensing Edge Wireless Transmitter/Receiver: Model MGLK20 Miller Edge Monitored Gate Link Transmitter and Receiver 19

22 AC 115V F FUSE 7 AMP Battery Module / Replace TEST Battery Battery Battery Battery Error PUTS Limit SW Wiring operator input ac power Wire input AC power wire to the PS24 power supply as shown. Choose either 115V or 230V setting on input AC power selector switch. NOTE: AC power wire is required for EACH gate operator when using dual gate operators. CAUTI: MAKE SURE CIRCUIT BREAKER IS BEFORE WIRG SUPPLY PS24 FUSE 7 AMP AC 7 Amp Fuse Input AC Options Single Phase 115VAC Only 115VAC 115V Set to 115V Line (Black) WARNG HIGH VOLTAGE disconnect power before servicing unit! Terminal PS24 Supply DO NOT TURN AT THIS TIME. DANGER HIGH VOLTAGE! Line (Black) Select Input Voltage: 115VAC or 230VAC warranty if label is REMOVED VOED 230V Input AC Selector Switch CAUTI: If power selector switch is set for 115V but input power is actually 230 V, 7 Amp Fuse will blow. 115 OR 230VAC Wire Neutral (White) Neutral (White) Single Phase 230VAC Only 230VAC 230V Set to 230V Chassis (Green) Chassis (Green) IMPORTANT NOTE: Make sure there are NO exposed bare wires at the power terminal connection. Operator MUST be Properly GROUNDED PS24 SUPPLY NOTE: Consult city codes for AC line wiring. Beware of existing underground services. Ground Rod within 10 ft of operator WARNG WARNG connect chassis to ground rod for lightning protection Battery Voltage E 1/2 /SOLAR BC7 TO CTROLLER Chassis Ground Chassis TWO Chassis Grounds are located inside either end of the conduit tunnel. Ground Conduit Tunnel WARNG connect chassis to ground rod for lightning protection Proper grounding of this gate operator is a requirement for LIGHTNG PROTECTI in lightning prone areas. To be effective, ground connections should be made with a minimum 12 AWG, 600 volt insulated wire to a ground point within 10 feet of the gate operator. The ground point must be at an electrical panel, a metallic cold water pipe that runs in the earth, or a grounding rod. 20

23 Wiring operator optional remote power supply kit max magic box A Magic Box Kit (sold separately) is required to remotely install the PS24 Supply from the gate operator. Remove PS24 power supply from gate operator and install in Magic Box, plug in power supply to PS24 connector. Wire input AC power to the PS24 Supply (See page 20 for wiring). Choose either 115V or 230V setting on input AC power selector switch. Run low voltage wires (not included) from the Magic Box connection and wire to /SOLAR connector (Polarity Matters!). Plug connector into /SOLAR port on the gate operator s BC7 battery module. NOTE: A Magic Box kit is required for EACH gate operator when using dual gate operators. At Magic Box DO NOT TURN AT THIS TIME. Ground Rod within 10 ft of Box In From PS24 Connector PS24 SUPPLY PS24 Supply FUSE 7 AMP WARNG! HIGH VOLTAGE disconnect power before servicing unit removed from operator PS24 Connect Input AC wire (See page 20 for wiring) AC Select Input Voltage: 115VAC or 230VAC warranty VOED if label is REMOVED Input AC Input AC Selector Switch CAUTI: If power selector switch is set for 115V but input power is actually 230 V, 7 Amp Fuse will blow. 230V DANGER HIGH VOLTAGE! NOTE: Consult city codes for AC line wiring. Ground IMPORTANT NOTE: imum Control s remote power supply technology does NOT Polarity Matters! utilize the battery power from the BC7 Battery Module during NORMAL gate operation. Battery power is reserved for backup power LY when an AC power failure occurs. As a result, battery life is NOT shortened. This low voltage system can CTUOUSLY cycle the gate during NORMAL gate operation, perfect for high traffic gate applications. Input 115 VAC or 230 VAC Input AC CAUTI: MAKE SURE CIRCUIT BREAKER IS BEFORE WIRG Pos + To Operator 24 VDC Low Voltage Wires 10 AWG imum Magic Box MUST be Properly GROUNDED IMPORTANT: Magic Box and Gate Operator MUST EACH be Properly GROUNDED. Proper grounding is a requirement for LIGHTNG PROTECTI in lightning prone areas. To be effective, ground connections should be made with a minimum 12 AWG, 600 volt insulated wire to a ground point within 10 feet of the Magic Box and gate operator. The ground point must be at an electrical panel, a metallic cold water pipe that runs in the earth, or a grounding rod. NOTE: Beware of existing underground services. /SOLAR Port /SOLAR Connector (Included in kit). Pos + Low Voltage Wire in Conduit /SOLAR TO CTROLLER Battery Voltage E 1/2 F / Battery Replace TEST Battery Battery Battery Error BC7 Battery Module BC7 Battery Module At Gate Operator 21

24 F Replace Battery Battery Phantom Battery Module TEST Battery Error AC FUSE Limit SW Wiring operator solar power connection optional Refer to Solar application guide. NOTE: Cover solar panel from sunlight BEFORE wiring plug to solar panel to prevent a shock from occurring. Solar Kit (Sold separately) Pos + Red Polarity Matters! Black connect to before use IMPORTANT Connect to /SOLAR /SOLAR TO CTROLLER Battery Voltage E 1/2 F / Replace Battery Battery TEST Battery Battery Error BC7 Battery Module STANDARD BC7 Battery Module (Approximately 450 cycles using only battery power) To Solar Kit Connect to /SOLAR Battery Voltage E 1/2 /SOLAR TO CTROLLER / BC36 Battery BC36 Phantom Battery Module (36 Amp/Hr) PS24 SUPPLY 7 AMP OPTIAL BC36 Phantom Battery Module The OPTIAL BC36 Phantom Battery Module is for high traffic cycling areas (Approximately 2000 cycles using only battery power). A BC36 phantom module is needed for each solar power kit used (One per gate operator when dual gate operators have been installed). It replaces the BC7 Battery module in the operator s battery position (see page 45). Operator cables reconnect to the same plugs on the BC36 as they did on the BC7 battery module. WARNG connect chassis to ground rod for lightning protection 115V PUTS 22

25 AC 115V F / Replace Battery Battery FUSE 7 AMP TEST PWR Battery Error M M NO / CLAMP SLIPPG 1.5Sec Wiring operator operators to matrix 1 Unscrew motor controller from operator to gain access to RS485 connector. Schematics on page 40 of manual shows where all plugs are located to reinstall motor controller. PS24 SUPPLY TAIL TIMER D AUTOMATIC / CTROLS SPEED MOTI N CLA LE DISABLE ALARM 12V Tamper USE Battery Voltage E 1/2 /SOLAR BC7 Battery Module TO CTROLLER PWR PWR not used not used RS485 RS485 ALARM PUTS Primary/ Primary/ Single Operator Limit SW PUTS Wire to 1 5 Wires to 1 22 AWG. 5conductor twisted pair, shielded cable LE LE Connect power wire from the Primary/Single motor controller to power 1. Connect (3) three RS485 wires from the motor controller to the 1. PWR RS485 RS485 PWR not used not used ALARM PUTS Primary/Single Operator NO to 1 22 AWG. 3conductor twisted pair, shielded cable 3 Wires to 1 PWR RS485 RS485 PWR not used not used ALARM PUTS Secondary Operator BiParting Gates Connect (3) three RS485 wires from the DARY operator s motor controller to the 1. DO NOT connect PWR. NOTE: Primary/Single operator closest to control box. Control Box 1 Secondary Primary/Single 3 Wires to 1 5 Wires to 1 23

26 Wiring operator optional key switch to Operator(s) The Optional Key Switch is independent of the 1 and allows the gate to be electronically moved open or closed by turning the removable key in either direction if you choose to connect the key switch. Connect (3) three wires from the Key Switch at the Control Box to the. NOTE: Each operator is specifically wired to the Optional Key Switch when installing dual gate operators if you choose to connect the key switch. (see illustrations). Secondary PUTS Open (Green) Gnd Close (White) Key Switch Terminal Primary/Single PUTS OUTSE Property DARY SE Property 22 AWG. 3conductor twisted pair, shielded cable Primary/Single Open Optional Open/Close Key Switch Primary/Single Open (Green) Close (White) Secondary are used. PWR RS485 RS485 ment Protection Sensor Guidelines PWR 12V ALARM Key Switch Terminal operator WILL NOT function. MITORED sensors LY, to each operator s when dual operators Wire NORMALLY D (N.C.) Reversing Edge and/or can be wired to ANY of the 3 Inputs. PWR 12V MUST be used to power MITORED sensors UNUSED inputs MUST remain JUMPERED or fault will occur. CAUTI: See installation instructions. ATTENTI: Voir la notice d installation. A sensor MUST be wired to or Monitored OR LY power entrapment protection sensors with PWR 12V PWR 12V MUST be used Monitored Reversing Edge PUTS In Inputs & MUST be LEARNED to MITOR sensors. To LEARN inputs & : MITORED Sensors MUST be wired to inputs BEFORE they can be learned. Any unused inputs MUST be jumpered. 2 3 PUTS Gnd PUTS PWR RS485 RS485 PWR 12V ALARM ment Protection Sensor Guidelines PUTS LY power entrapment protection sensors with PWR 12V PWR 12V MUST be used A sensor MUST be wired to or operator WILL NOT function. Wire NORMALLY D (N.C.) In MITORED sensors LY, to each operator s when dual operators are used. be wired to ANY of the 3 Inputs. Reversing Edge and/or can Monitored Reversing Edge PWR 12V MUST be used to power MITORED sensors UNUSED inputs MUST remain OR JUMPERED or fault will occur. 2 3 Inputs & MUST be LEARNED to MITOR sensors. To LEARN inputs & : Monitored CAUTI: See installation instructions. ATTENTI: Voir la notice d installation MITORED Sensors MUST be wired to inputs BEFORE they can be learned. Any unused inputs MUST be jumpered. 2. Reversing Edge and/or can be wired to either input 2 or Press and HOLD the & buttons at the same time on 1 until beep is heard, learn mode begins. MOTI 2 3 unused inputs Learn mode lasts for 5 min. indicated by beeping. 4. LEDs WILL be for each detected sensor on. LEDs WILL be for BOTH s when dual operators are used. 5. Press button again within 5 min. to learn sensors and end learn mode, beeping stops. Inputs are now MITORED. ment Protection Inputs: MUST jumper Limit SW PUTS PUTS Secondary unused inputs Limit SW Learn mode lasts for 5 min. indicated by beeping. 4. LEDs WILL be for each detected sensor on. LEDs WILL be for BOTH s when dual operators are used. 5. Press button again within 5 min. to learn sensors and end learn mode, beeping stops. Inputs are now MITORED. ment Protection Inputs: MUST jumper 2. Reversing Edge and/or can be wired to either input 2 or Press and HOLD the & buttons at the same time on 1 until beep is heard, learn mode begins. MOTI Primary OUTSE Property DARY SE Property Primary/Single Open Control Box Key Switch Secondary Primary/Single 3 Wires to Key Switch 3 Wires to Key Switch 24