Motivia Motorization

Transcription

1 STEP BY STEP INSTALLATION INSTRUCTIONS Luxe Linen Honeycomb Shades Skylight Motivia Motorization

2 Everything You Need Table of Contents Step 1 - Getting Started....3 Overview - Motorized Honeycomb Skylight...4 Step 2 - Battery Pack Placement....5 Step 3 - Installing the Brackets....6 Step 4 - Linking the Remote...7 A Smooth Set-Up We want you to love your new window coverings and that includes having a smooth installation experience. We recommend saving this guide. If you encounter any difficulties or questions, please reach out to us for help. It s why we re here. Call us at for more info on installation. We recommend you hold on to all packaging until your window coverings are fully installed. Should something go wrong (we strongly doubt it), we want any potential returns to be a painless as possible. Step 5 - Installing the Top Rail....8 Step 6 - Installing the Bottom Rail...9 Step 7 - Installing the Tracks Step 8 - Operating the Shade Step 9 - Adjusting the Limits Step 10 - Setting Favorite Positions Step 11 - Advanced Programming Step 12 - Leveling the Shade Step 13 - Charging the Shade Battery Step 13 - Removing & Replacing Remote Battery Removing the Shade Troubleshooting Customer Service Hours Monday Friday: 6am 6pm PT Saturday Sunday: 7am 4pm PT Care & Cleaning Safety Warranty...Back Cover smithandnoble.com 1 smithandnoble.com

3 Step 1 Parts & Tools Overview Getting Started Motorized Honeycomb Skylight First, make sure you have all the parts and tools required to install your shades. ALL THE HARDWARE YOU LL NEED: Pencil, screw-driver, ¼ nut driver, level, and a drill with a 1 16 drill bit. Then find wooden studs where you ll want to attach the brackets; if you need to mount your shades to wallboard or plaster, use a secure fastener designed for hollow wall applications. For metal surfaces, pre-drill holes and use the included screws. For concrete, stone, brick, or tile surfaces, use a masonry drill and appropriate plugs, anchors, or screws. Additional fasteners other than those sent with your shade may be required. It s important when selecting a fastener to make sure it s designed to support the weight of the shade. Follow the fastener manufacturer s instruction from there on out. SCREWS MOUNTING BRACKETS PENCIL (NOT INCLUDED) LEVEL (NOT INCLUDED) SCREWDRIVER (NOT INCLUDED) POWER DRILL & LEVEL (NOT INCLUDED) 3 smithandnoble.com

4 Step 2 Battery Pack Placement Step 3 Installing the Brackets Placement of Battery Pack Shades 20" wide and wider have the rechargeable battery inside the head rail. Shades under 20" wide require the rechargeable battery to be mounted on the back of the head rail. This requires an additional 1/2" clearance for mounting. 3" Shades are shipped with the required number of brackets for proper installation. End brackets should be located approximately 3" from either end. SHADES UNDER 20" WIDE 1/2" MOUNTING BRACKETS Depending on the width of the shade, additional brackets may be necessary, evenly spaced between the two end brackets. Using the mounting bracket as a template, measure to the edge of the bracket and mark the hole locations with a pencil for drilling. When mounting brackets, make sure they are in line with each other. 5 smithandnoble.com

5 Step 4 Link Remote Step 5 Installing the Top Rail MOTOR Important: Please read through this section completely before beginning Start with the top rail/fabric assembly. The top rail is the rail with the motor The remote control has multiple channels. Before linking the remote, determine which shade you want on which channel. The standard remote has 5 channels. All shades linked to a remote will also automatically be programmed to the "ALL" channel. SETTING (black button) Located inside the headrail. Remove shade from the window to access the setting button. A HEADRAIL TOP RAIL SHADE in it. Position the rail with the front lip (A) resting on the hooks of all the brackets. Push the rail firmly up and toward the window until the groove on the rail snaps into place, (B) as shown. It is recommended to only link one shade per channel unless it is absolutely necessary to group shades other than the "all" channel. This simplifies adjusting limits and setting favorites CHANNEL DISPLAY BOTTOM RAIL Remove plastic film from the front of the remote. If battery is not already installed in the remote, follow the instructions on pg Select the channel that you want to link the shade to, using the CHANNEL selector button. 2. Press the SETTING button on the motor until the motor starts to beep. Release the button immediately after the beeps start. The motor will make 4 fast beeps followed by 5 long beeps. Press the CONFIRM button on the remote anytime during the series of long beeps. It must be pressed before the last long beep. The motor will respond with 3 fast beeps confirming that the shade has been linked. 3. Repeat step 2 for all shades that will be controlled by the same channel (it is not recommended to put more than one shade on a channel). 4. Repeat steps 1-3 to link the remaining shades to the rest of the channels. FRONT OF BACK OF UP STOP/FAVORITE DOWN CHANNEL + CHANNEL LIMIT CONFIRM B 7 smithandnoble.com

6 Step 6 Installing the Bottom Rail Step 7 Installing the Tracks Use the remote to lower the bottom rail all the way down so that it can be attached to the bottom brackets. Select the desired channel with the CHANNEL key. The channel indicator light will illuminate the channel that is on. If all 5 lights are lit, the remote will control all 5 channels at once CHANNEL DISPLAY UP STOP/FAVORITE DOWN CHANNEL + CHANNEL FRONT OF TRACK OVERLAPS FRONT OF RAILS Place the track against the front of the top and bottom rails. Attach the track with the screws provided. Space the screws no more than 12" apart. Follow the same procedure for the other track. Make sure that the 2 tracks are parallel to each other. Press the DOWN key to lower the shade. FRONT OF B 4" A ATTACHMENT SCREWS Position the rail with the front lip (A) resting on the hooks of all the brackets. Push the rail firmly down and toward the window until the groove on the rail snaps into place, (B) as shown. 12" 12" 12" 9 smithandnoble.com

7 Step 8 Operating the Shade Step 9 Adjusting the Limits Operating the Shade Set the Limits on Primary Remote 1. Select the desired channel with the CHANNEL key. The channel indicator CHANNEL DISPLAY The lower and upper limits have been set at the factory. If you need to make light will illuminate the channel that is on. If all 5 lights are lit, the remote will control all 5 channels at once. 2. Tapping the UP or DOWN keys for less than 2 seconds will move the shade in short steps. Holding the UP or DOWN keys down for more than 2 seconds UP STOP/FAVORITE DOWN CHANNEL + CHANNEL LIMIT CONFIRM adjustments to the limits, follow the instructions on page 9. Use the CHANNEL key to select the channel for the shade that needs to be adjusted. Then follow the directions below. If only adjusting one shade on a channel, unplug the other shades. before releasing, will operate the shade in the faster standard speed. 3. Press the UP or DOWN keys to raise or lower the shade. FRONT OF BACK OF Please Note: When clearing the factory set limits, both the upper and lower limits will need to be reset. 4. Press the STOP key to stop the shade anywhere along the travel. Use the CHANNEL buttons to select the channel for the shade that needs to be adjusted. Then follow the directions below. When adjusting one shade any other shades on that channel need to be temporarily unplugged. To unplug a shade, remove the shade from the window and unplug the battery pack from the motor. Repeat for all other shades on that channel. Follow the limit setting instructions on next page and then reattach plug on "turned off" shades. 11 smithandnoble.com

8 Step 9 Adjusting the Limits Step 10 Setting Favorite Positions Setting the LOWER LIMIT Setting a Favorite Position 1. Hold the LIMIT button until the shade starts beeping CHANNEL DISPLAY 1. Use the UP or DOWN buttons to position the shade at the desired "FAVORITE" position. 2. After the shade stops beeping, use the DOWN button to lower the shade. Press STOP when the shade is near the desired lower limit. 3. Press the UP and DOWN buttons to adjust the length more accurately. UP STOP/FAVORITE DOWN CHANNEL + CHANNEL LIMIT CONFIRM 2. While holding the LIMIT button, quickly press and hold the UP button. 3. Release both buttons when the shade makes a series of short beeps Using a Favorite Position 4. Press and Hold the CONFIRM button until the shade makes a series of short beeps. This locks in the lower limit. FRONT OF BACK OF 1. With the shade at either the upper or lower limit, simply press the STOP/ FAVORITE button to bring the shade to the "FAVORITE" position. 2. To go to the "FAVORITE" position from any other location, make sure the shade has been stopped for at least Setting the UPPER LIMIT three seconds before pressing the STOP/FAVORITE button. 1. Press the UP button to raise the shade. Changing a Favorite Position 2. Press STOP when the shade is near the desired lower limit. 1. Press the UP or DOWN buttons to position the shade at the desired "FAVORITE" position. 3. Press the UP and DOWN buttons to adjust the upper limit more accurately. 4. Press and Hold the CONFIRM button until the shade makes a series of short 2. While holding the LIMIT button, quickly press and hold the UP button. Release both buttons when the shade makes a series of short beeps. beeps. This locks in the upper limit. 2. To erase a "FAVORITE" position, bring the shade to the upper limit. Press and hold the LIMIT button the the back of the remote, then press and hold the UP botton. Release both buttons when the shade makes a series of short beeps. 13 smithandnoble.com

9 Step 11 Advanced Programming Step 11 Advanced Programming Replace Original Remote or Add Additional Remote MOTOR Remove/Link a Shade from One Remote/Channel to Another 1. Select the channel that you want to 1. Unlink the motor from the remote program using the CHANNEL selector button. Note: All shades on that channel will be unlinked. If you have shades on a 2. Press the SETTING button on the motor until the motor starts to beep. 3. Release the button immediately after the beeps start. The motor will make 4 fast beeps followed by 5 long beeps. SETTING BUTTON (Black) Remove from window (when needed), to access the settings button. channel that you do not want to unlink, you must temporarily unplug the motor from the battery pack (headrail). a. Select the Channel that you want to unlink using the CHANNEL selector button. 4. Press the CONFIRM button on the remote anytime during the series of long beeps. It must be pressed before the last long beep. The motor will respond with 3 fast beeps confirming that the shade has been linked CHANNEL DISPLAY UP STOP/FAVORITE b. Press and Hold the CONFIRM button. The shade will make a series of fast beeps. (4 beeps/pause/4 beeps/pause/8 beeps) c. When the series of beeps is complete, release the CONFIRM button. All shades previously linked to selected channel will 5. Repeat steps 1-4 to program the rest of the channels on a multi-channel remote. 6. ALL shades linked to a remote will also automatically be programmed to the DOWN CHANNEL + CHANNEL LIMIT CONFIRM now be unlinked. 2. Link the motor to the new remote or channel. "ALL" channel. FRONT OF BACK OF a. Follow the steps for replacing the remote to the left. b. Set the lower and upper limits by following the instructions on Pg smithandnoble.com

10 Step 12 Leveling the Shade Step 13 Charging the Shade & Remote Batteries Level the Moving Rail Motorized Skylight Shades use a system that allows easy leveling of the moving rail. It is designed to make slight adjustments (Less than 1") to level the moving rails of your shade. It is not designed to make length adjustments. ADJUSTMENT SCREWS CHARGING WIRE Charging the Shade Battery When the shade begins to operate slower than normal, it is time to charge the battery. Plug the 8.4v charger into the charging wire. The charging wire is attached to the back of the headrail at the right end. Plug the charger into an electrical outlet. Use a flat head screwdriver or a coin A red light on the charger indicates that (a quarter works the best) to turn the the battery is charging. adjustment screw to raise or lower that side of the bottom rail. The adjustment screw is on the top of the moving rail. One quarter turn of the screw will move the moving rail up or down approximately 1 4". Over-turning the adjustment screw (more than 1" of adjustment) can cause the cord to tangle or wedge inside the rail. The screw should turn easily - Do Not Force. ADJUSTMENT SCREWS If the rail is uneven at the top, raise the low side with the outer adjustment screw. If the stack is uneven at the bottom, lower the high side with the inner adjustment screw. BACK OF REMOTE PULL BATTERY TRAY OUT HERE. (turn remote over to front first, battery might fall out.) To fully charge the batteries, allow the batteries to charge for 1 hour after the light on the charger turns green. A typical charge cycle can take between 4-6 hours. Replacing the Remote Battery Remove the battery tray from the remote by inserting a fingernail into the indentation on the back of the remote. To avoid the battery falling out of the remote, remove the tray while the remote is face up. Insert the new battery (CR2430 lithium) into the battery tray so that the writing is facing up (positive up) when the remote is facing up. Slide the tray back BATTERY LITHIUM BATTERY CR2430 3V into the remote. ADJUSTMENT SCREWS BATTERY TRAY FRONT OF REMOTE 17 smithandnoble.com

11 Removing the Shade Troubleshooting To remove a shade, insert a flat blade screwdriver between the rail and the bottom back of the bracket (tab which extends out slightly from each bracket). Gently pry the screwdriver to release the bracket from the headrail. Take care not to damage the painted finish of the headrail. As you release the brackets, support the headrail to keep it from falling. Insert screwdriver and gently pry PROBLEM 1 The motor does not work and the shade is stuck in the closed position SOLUTION 2 The motor does not work 1. Recharge Battery. 3 The indicator light on the remote does not shine or the remotecontrolling range becomes shorter. Carefully pull down on the moving rail enough to allow access. Follow solution below. If this is required, limits will need to be reset. See Adjust Motor Limits section for setting limits. Replace the battery in the remote (CR2032 Lithium) For additional help call us at smithandnoble.com

12 Care & Cleaning Safety Care & Cleaning Occasional light vacuuming with a soft bristle attachment or gentle feather dusting is all that is required to keep your blinds looking fresh and neat. Most stains can be blotted with a damp sponge and mild detergent. Before using anything stronger than mild detergent and lukewarm water, test an Safety First. Style Second To None. Great style should never come at the cost of safety. Every Smith & Noble window treatment conforms strictly to today s safety standards, including permanent tie-down devices and built-in cord stops. To protect young children and pets, there s no better way to eliminate risk than to use one of our cordless products. unobtrusive corner of the shade. If you have any questions, call us at , we would be glad to help. 21 smithandnoble.com

13 Warranty Service The enjoyment of your window coverings should be everlasting, which is why our products come with a limited lifetime warranty. The warranty applies to the original owner, requires a proof of purchase and covers defects in material or craftsmanship. Shades or blinds must have been properly installed. We reserve the right to determine if your window covering warrants a repair or a replacement. In need of warranty service? Call us at and we ll arrange for a repair or replacement ASAP. SN_LL_SM_2017_1 SN Smith & Noble Home, Inc. All Rights Reserved SN 2042