SKEENA SUBDIVISION. Mile TERRACE Y 0.0 AMSBURY 9.6 EXSTEW SALVUS KWINITSA SKEENA 58.5 TYEE SOCKEYE 78.

Transcription

1 [107 ] Method of Control W SKEENA SUBDIVISION E Mile Siding Capacity In Feet DOB / TGBO SWITCHING ZONES Hot Box and Dragging Equipment Detectors RTC Radio Channel, Tones and DTMF Codes TERRACE Y AMSBURY 9.6 EXSTEW CTC SALVUS KWINITSA SKEENA 58.5 TYEE SOCKEYE 78.3 TGBO C2 T WATSON ISLAND SUBD TRK NEMOTO PRINCE RUPERT Y 94.6 M of W Channels (Ch ) (Ch ) (Ch ) (Ch ) (Ch ) 1 SIDING CONTROL TERRITORY 2 RTC II ADVANCED TRAIN CONTROL FEATURES 3 TERRACE (a) Switching Signals: 11D, 12D (b) Anti-Whistling - Except in emergency, Rule 14(l) not applicable at: Mile 1.15 (c) Mile (Crossing) AWD have been upgraded to include integration with the traffi c signals. DTMF Crossing Activator System in place and must be used when governed by Rule 103.1(b). Provisions of 103.1(b) also applicable on Track BF11 (West Pullback). CH 1 Activate Main Track DTMF # Track BF11 DTMF # Deactivate Main Track DTMF # Track BF11 DTMF # If necessary to make a reverse movement on either of the above tracks, the DTMF codes must be applied in addition to the requirements of CROR Rule 103.1(a). Lunar lights located on crossing bungalow will illuminate indicating that it is permissible for the movement to proceed onto the crossing. Movements must occupy crossing surface within 3 minutes or the warning devices will deactivate. (d) Rule 112 (ii) - applicable as follows: Terrace Tracks BF15 to BF23 1 car 1 hand brake 2 or more cars 2 hand brakes

2 [108 ] Terrace Tracks BF11 to BF14 1 car 1 hand brake 2 cars 2 hand brakes 3 or more cars 3 hand brakes (e) Designated Locomotive Tie-up BF 40, 41, 42 (f) Equipment Restrictions - Track BF68: Heaviest car permitted (including contents) 250,000 lbs. Locomotives in Groups E, F, G, and H are not permitted. Wye: Tracks BF59, 60 and 61. Speed - 6 mph. Locomotives in series EF-644e, GE-9s numbered 2643 and higher are restricted from operating on wye and connecting tracks. Loaded Coal Trains: may only operate on tracks BF11 to BF 14 inclusive. (g) Yarding Instructions: All trains must contact the Prince George Pod on CH 3 - DTMF * 1. (h) Imperial Oil Spur Track BF 27: Due to fi re hazard, locomotives are only permitted to operate up to the signs posted on this spur. No open fl ame appliances or smoking permitted while on this trackage. If reachers are required, such cars must not be equipped with an operating source of ignition. (i) Tracks BF11, 12, 13 and 14 Speed - 10 mph. 4 NEMOTO (PRG / RTI) (a) Rule 112 (ii) - applicable as follows: Ridley Island: Prince Rupert Grain Tracks SF-71, SF-72, SF-73 and SF-74; 1 car 1 handbrake 2 or more cars 2 hand brakes. (b) Rule Self restoring derail and switch: Nemoto - DTMF 10#1011-PRG. DTMF 10#1021-RTI. (c) Designated Locomotive Tie-up Ridley Island - SF 69 and SF 70 5 PRINCE RUPERT (a) Prince Rupert Intermodal - All trains entering subdivision track at Nemoto should make personal or radio contact with the Fairview Terminal crews to ensure that each has a clear understanding of the other crews intended movements and make arrangements to avoid confl ict prior to entering aforementioned trackage. If unable to contact Fairview Terminal, conact must be made with the RTC for further instructions. (b) Rule 14(l) Must be sounded one quarter mile from private crossing at Mile (c) Rule 112 (ii) - applicable as follows: Prince Rupert Yard: ALL TRACKS, 1 or more cars, 1 hand brake (d) Switches between mileages 91.0 and 94.6 may be left lined and locked in either position. (e) Prince Rupert - All tracks other than Subdivision Track west of Mileage Speed 10 mph.

3 [109 ] (f) Designated Locomotive Tie-up : Ridley Island - SF 69 and SF 70 (g) Private crossing at grade Mile Cars must not be left within 150 ft of crossing on all tracks. (h) Prince Rupert Ferry Slip. Before movements proceed onto apron, crews must fi rst ensure that all fastenings have been made secure. Speed to be governed by loading conditions and in no case exceeding 5 mph when movement is being made over apron or on the deck of barge. Movements must have air brakes cut in at all times when loading and unloading barges. Locomotives are restricted from operating over apron or deck of barge. (i) WYE - Speed 5 mph. 6 APPLICABLE ON SUBDIVISION (a) Rule 105(a) applicable on all trackage where Rule 105 applies, except sidings Exceptions: Not applicable at Terrace Tracks BF11-BF23. On these tracks, foremen requiring protection for track units must provide positive protection by locking out the track through the use of special locks or by the use of the red signals as prescribed by Rule 40.1, ensuring that they will be visible to all trains and engines, moving and or switching within these limits. (b) Locomotives must not be operated over trestle on Woodroom lead located on extreme south side of Skeena Cellulose Watson Island Pulp Mill trackage. (c) Mile 87.2 (Bridge) - Trains handling cars in excess of 276,000 lbs must not exceed 15 mph while such equipment is on bridge. (d) Slide Detector Fence Mile to Mile ft. (e) Hazard Warning System Mile to ft. Mile ft. Mile ft. Mile to ft. Mile to ft. (f) Avalanche Zones Mile 27.5 and Mile 30.0 Mile 39.3 and Mile 47.1 Mile 49.5 and Mile 53.0 Location of avalanche equipment: Mile Salvus highway maintenance camp. Mile Kwinitsa generator compound. (g) Mile Hot Box and Dragging Equipment Detector is located in an avalance zone. Whenever a train is required to be inspected as a result of a reading from this detector the following will apply during periods of avalanche warnings. DANGER: Trains may be inspected outside of the avalanche zone, but must be inspected before the suspect equipment is allowed to move over any dual control switch.

4 [110 ] Movement to the fi rst suitable inspection location must be made consistent with safety and good train handling techniques, including reducing speed immediately to 10 mph or less, in the case of a DRAGGING EQUIPMENT alarm, an immediate controlled stop must be made and the pullby provision are not applicable. 7 SPEEDS Mile Psgr Frt 0.0 to 5.4 Zone (Crossing) PSGR 35 MPH APPROACHING WITHIN 2700 FT UNTIL FULLY OCCUPIED 3.8 to to 14.7 Zone to 8.6 PSO to 13.7 PSO to 26.6 Zone to 20.7 PSO to 30.6 Zone to 26.8 PSO to 46.1 Zone to 34.5 PSO SALVUS SIDING to 38.2 PSO to 41.5 PSO to 52.6 Zone to 47.6 PSO to 64.2 Zone to 77.5 Zone to 65.3 PSO to 67.1 PSO to 72.4 PSO to 77.2 PSO to 85.6 Zone to 91.0 Zone to 87.1 PSO to 94.6 Zone (Crossing) WESTWARD 10 MPH APPROACHING WITHIN 1200 FT UNTIL FULLY OCCUPIED (Crossing) EASTWARD FROM FERRY SLIP LEAD SWITCH 10 MPH UNTIL FULLY OCCUPIED 8 SPECIAL INSTRUCTIONS APPLICABLE ON SPURS AND OTHER TRACKS (a) Mile West Fraser Mills Ltd. - Capacity 1950 ft. Switch points face east. Public Crossing at Grade: Mile 0.06 (Highway 16) - AWD: STOP signs on both sides of crossing. (b) Mile Ridley Island Lead - Extends south from Nemoto and includes Ridley Terminals Inc. and Prince Rupert Grain Ltd. Nemoto Power-Operated Switch The power operated switch (Bull Switch) is equipped with an indicator light mounted on the housing of the switch machine and displays the following indications: Green light: Route is lined for PRG. (DTMF10#1011)

5 [111 ] Yellow light: Route is lined for RTI. (DTMF10#1021) No light: Switch is not properly lined for either route and must be operated by hand. In the absence of an indication light (no light), the power-operated switch must be operated by hand. Switch must be taken off power, placed in hand position, the points must be engaged and lined for the route to be used. Switch must be lined in all instances. This condition must be reported to the RTC as soon as practicable. Prince Rupert Grain Terminal Ltd. (PRG) Before moving foul of ladder tracks, when Prince Rupert Grain (PRG) engine is in the vicinity, engine crew will make personal contact with PRG crew to ensure each has a clear understanding of the other crew s intended movements and make arrangements to avoid confl ct. CN engines must not enter PRG elevator, runaround, or transfer tracks without permission from PRG or RTC. Certain switches along the south ladder track may be operated manually or by pushbutton electric trackside control. In electric trackside control mode the position of the switch is reversed by pressing the Reverse button located in the blue box adjacent to each switch. PUSH-BUTTON MUST BE DEPRESSED UN- TIL SWITCH POINTS ARE PROPERLY LINED. Instructions for manual operation of switches are contained inside the blue box. Route Indicator lights at each switch indicate whether switch is lined for straight track or diverging route. BEFORE PROCEEDING OVER THESE SWITCHES IT MUST BE DETERMINED BY VISUAL INSPECTION OF SWITCH POINTS THAT THE SWITCH IS PROPERLY LINED REGARD- LESS OF THE INDICATION OF THE ROUTE INDICATOR LIGHT. Ridley Terminals Inc. (RTI) Movements must not enter the thaw shed, indexer or dumper unless accompanied by an employee of Ridley Terminals Inc. Restricted clearance inside THAW SHED, INDEX- ER and DUMPER. Locomotives equipped with bay windows are not permitted within the thaw shed, indexer or dumper. Awnings and wind defl ectors on all locomotives must be placed in closed position before entering the thaw shed. Crews will use extreme caution in the vicinity of the thaw shed, indexer and dumper, entraining and detraining only when train or engine is stationary and then only when necessary. Speed through thaw shed, indexer and dumper is 5 mph.