2.3. Molded Case Circuit Breakers. Series C. Accessories Selection Guide and Ordering Information

Transcription

1 Molded Case Circuit s Series C.3 Accessories Selection Guide and Ordering Information Line and load terminals provide wire connecting capabilities for specific ranges of continuous current ratings and wire types. Except as noted, terminals comply with Underwriters Laboratories Standards UL 486A and UL 486B. Unless otherwise specified, F- circuit breakers are factory equipped with load terminals only. Amperes Terminal Body Material Ordering Information F- circuit breakers and molded case switches have load terminals only as standard equipment. When standard line-end terminals (same as standard load-end terminals) are required, add Suffix L to the circuit breaker catalog number. When nonstandard or optional line and/ or load terminals are required, order by style number. Specify if factory installation is required. Wire AWG Wire mm Package of Three Terminals Standard Pressure Terminals 0 (EHD) Steel Cu/AI T0FB 100 Steel Cu/AI 14 1/ T100FB 5 Aluminum Cu/AI 4 4/ TA5FD Optional Pressure Terminals 50 Aluminum Cu/AI TA50FB 100 Aluminum Cu/AI 14 1/ TA100FD 00 Stainless steel Cu 4 4/ T150FB 5 Copper Cu 4 4/ T5FD 5 Aluminum Cu/AI kcmil TA5FDK3 3 5 Aluminum Cu/AI kcmil TA5FDK Use on FDE, HFDE and FDCE electronic trip only. Not for use with ED, EDH, EDC breakers. 3 Includes terminal shield kit. Adds approximately 3 inches (76.) to breaker height. Available for use on three-pole breaker only. 4 Replacement use only. Volume 4 Circuit Protection CA E August V4-T-147

2 .3 Molded Case Circuit s Series C Washer Wire Clamp 3T0FB 3T100FB, 3T150FB 3TA5FD Assemble wire clamp to bottom of conductor as shown. Insert collar enclosing conductor as shown. Locate nut on top of conductor and tighten securely with screw and washer. Caution: must surround conductor. Washer Washer 3TA50FB 3TA100FD 3TA5FDK3 (Up to 150 mm ) Assemble collar on top of conductor as shown. Tighten securely with screw and washer. Nut slides onto conductor and is held in position by a screw and lockwasher. Extrusion Clip Insert collar enclosing conductor and center on extrusion on collar. Install clip with legs on top of conductor and snap end around bottom of collar. Assemble collar on top of conductor as shown. Tighten securely with screw and washer. Terminal shield must be used with this collar. Note: For 185 mm, use 3TA5FDK1. Same illustration for 3TA5FDK V4-T-148 Volume 4 Circuit Protection CA E August 016

3 Molded Case Circuit s Series C.3 Product Selection FD Series C High Performance Ratings Product Amperes 480 Vac (UL) 600 Vac (UL) FDC 3P thermal-magnetic only With limiter FD IC Rating 00 kaic at 600 Vac 1 Ampere Rating Limiter Terminals Amperes Load Terminals (For Line Mounted Limiters Only) with Line Side Mounted Current Limiter 1 Line and load terminal included. Two interphase barriers provided, mounted on line end of limiter, catalog number FJ1PBK. 3 Four interphase barriers provided, () line end of breaker, () load end of limiter. 4 Load side breaker terminations included for units configured with line mounted limiters. with Load Side Mounted Current Limiter 3 Thermal-Magnetic 40 FDC3040Q01 FDC3040YQ0 45 FDC3045Q01 FDC3045YQ0 50 FDC3050Q01 FDC3050YQ0 60 FDC3060Q01 FDC3060YQ0 70 FDC3070Q01 FDC3070YQ0 80 FDC3080Q01 FDC3080YQ0 90 FDC3090Q01 FDC3090YQ0 100 FDC3100Q01 FDC3100YQ0 110 FDC3110Q01 FDC3110YQ0 15 FDC315Q01 FDC315YQ0 150 FDC3150Q01 FDC3150YQ0 175 FDC3175Q01 FDC3175YQ0 00 FDC300Q01 FDC300YQ0 Terminal Body Material Wire mm AWG Wire / of s Standard Pressure Terminals 50 Aluminum Cu/Al #8 350 (1) TA50FJ 4 Amperes Terminal Body Material Wire AWG Wire mm Package of Three Terminals Standard Pressure Terminals 100 Steel Cu/AI 14 1/ T100FB 5 Aluminum Cu/AI 4 4/ TA5FD Volume 4 Circuit Protection CA E August V4-T-71

4 .4 Molded Case Circuit s Definite Purpose Features Base Mounting Hardware English base mounting hardware is included with GP frame only. For all other frames, order base mounting hardware separately as per the table to the right. Both line and load terminals are included with GP- Definite Purpose breakers. For all other frames, add L for line and load terminals to be included or W for no terminals. Accessories End Cap Accessory Kit End caps for line and load conductor termination are optional with each breaker. End caps secure the conductor with a ring-type connector. The kit includes one end cap, three cap screws, three nuts and three lock washers. Series C Accessories For internal accessories, see Page V4-T-73. For external accessories, see Page V4-T-304. Base Mounting Hardware English Metric GP Included FP BMH1 BMH1M KP BMH3 BMH3M LP BMH4 BMH4M MP BMH5 BMH5M Note: Base mounting hardware, is included with GP- breakers. A separate catalog number is not required. Line and Load Termination Optional Termination 1 Package of three terminals. Replacement use only. End Cap Accessory Kit Awg Wire (mm) Wire Bolt Size English Bolt Size Metric Torque Lb In Torque Nm GP Wire #14 1/ Cu only Included Amperes Awg Wire Wire with Control Wire Termination FP 100 #14 #10 Cu/Al 3T100FB #8 Cu/Al 3T100FB #6 #4 Cu/Al 3T100FB #3 4/0 Cu/Al 3T100FB 1 00 #3 4/0 Cu only 3T150FB 1 5 #4 4/0 Cu/Al 3TA5FB 1 5 #6 300 Cu/Al 3TA5FDK3 1 5 #6 300 Cu/Al 3TA5FDK 1 KP (1) Cu/Al TA350K 400 3/0 50 () Cu/Al 3TA400K 1 3TA400KCW LP () Cu/Al TA60LD TA60LDCW () Cu/Al 3TA603LDK 1 3TA603LDKCW MP 800 3/0 400 (3) Cu/Al TA800MA TA800MACWT () Cu/Al TA801MA TA801MACWT V4-T-334 Volume 4 Circuit Protection CA E August 016

5 Molded Case Circuit s Specialty s.6 Accessories Selection Guide and Ordering Information Enclosures 1 General Purpose Surface or flush mounting ampere range 600 Vac, 500 Vdc 1 enclosed breakers are designed for use in commercial buildings, apartment buildings and other areas where a general purpose enclosure is applicable. The breaker is front operable and is capable of being padlocked in either the ON or OFF position. Ratings through 100 amperes are listed with Underwriters Laboratories as approved for service entrance application. Both surface and flush mounted enclosures are available. 3R Rainproof Surface Mounting Interchangeable hubs (through 400 amperes) ampere range 600 Vac, 500 Vdc This general purpose outdoor service center employs a circuit breaker inside a weatherproof sheet steel breaker enclosure to serve Enclosure Selection Data Amperes FG 15 5 JG KG LG NG Enclosure Class 1 3R 1 1 3R 1 1 3R 1 1 3R 1 1 3R 1 as a main disconnect and protective device for feeder circuits. Ratings through 100 amperes are listed by Underwriters Laboratories as suitable for service entrance application. 1 Dustproof Surface Mounting No knockouts or other openings ampere range 600 Vac, 500 Vdc The 1 enclosure is designed in line with specifications for special industry applications where unusually severe conditions involving oil, coolant, dust and other foreign materials exist in the operating atmosphere. The handle padlocks in the OFF position and the cover is interlocked with the handle mechanism to prevent opening the cover with the circuit breaker in the ON position. Ratings through 100 amperes are listed by Underwriters Laboratories as suitable for service entrance application. SFDN5 RFDN5 JFDN5 SJDN50 RJDN50 JJDN50 SKDN400 RKDN400 JKDN400 SLDN600 RLDN600 JLDN600 SNDN100 RNDN100 JNDN100 Options and Accessories Standard Terminals Max. Amp Rating Neutral Kits, Insulated and Groundable Internal Accessories Auxiliary Switch AWG Wire mm FG / T100FB 1 FG / TA5FD 1 JG kcmil TA50KB KG kcmil TA350K KG 400 3/0 50 kcmil () TA400K 1 LG kcmil () TA603LDK NG kcmil () TA700NB1 NG /0 400 kcmil (3) TA1000NB1 NG 100 4/0 500 kcmil (4) TA100NB1 Max. Enclosure Rating (Amperes) Main Lug Size Cu/Al Ground Lug Size Cu/Al 100 (1) 14 1/0 (1) 14 1/0 INK (1) kcmil (1) kcmil INK (1) kcmil or (1) kcmil INK400 () 1/0 50 kcmil 600 () kcmil (1) kcmil INK (3) 1/0 to 750 kcmil or (4) 1/0 to 750 kcmil Factory Mounted 1A-1B Field Kit (1) 6 50 kcmil INK100 Factory Mounted A-B Field Kit FG 3 A06 A1X1PK A13 AX1RPK JG A06 A1XPK A13 AXPK KG A06 A1X3PK A13 AX3PK LG A06 A1X4PK A13 AX4PK NG A06 A1X5PK A13 AX5PK Shunt Trip Factory Field Kit Rating Mounted FG Vdc S0 SNT1LP03K JG 1 4 Vdc S4 SNTP04K KG 1 4 Vdc S4 SNT3P04K LG 1 4 Vdc S0 SNT4LP03K NG 1 4 Vdc S0 SNT5LP03K 1 Package of three terminals. Other accessories are available. Same as standard frame breakers. 3 Field installation on the FG is not UL listed. Volume 4 Circuit Protection CA E August V4-T-345

6 .6 Molded Case Circuit s Specialty s DC Terminal Wire s Ampacity Note: RGHDC breakers include six rear connectors as standard. Molded Case Switches Eaton s DC molded case switches are used in applications requiring a compact, high-capacity disconnect. They are UL 489 listed and have automatic high instantaneous current protection. These devices do not provide overload protection. Molded Case Switches Note 1 Four-pole frame with two-pole connected in parallel. Terminal Body Material Wire AWG Wire / of s mm of Terminals Included Standard Terminal EGEDC, EGSDC, EGHDC 100 Aluminum Cu/Al 14 1/ TA15EF HFDDC 0 Steel Cu/Al (1).5 4 (1) 3 3T0FB 100 Steel Cu/Al 14 1/0 (1).5 50 (1) 3 3T100FB 5 Aluminum Cu/Al 4 4/0 (1) 5 95 (1) 3 3TA5FD JGEDC, JGSDC, JGHDC 50 Stainless steel Cu (1) (1) 1 T50FJ HJDDC 50 Aluminum Cu/Al kcmil (1) (1) 1 TA50KB HKDDC 5 Aluminum Cu/Al kcmil (1) (1) 1 TA300K 350 Aluminum Cu/Al kcmil (1) (1) 1 TA350K 400 Aluminum Cu/Al 3/0 50 kcmil () (1) 3 3TA400K LGEDC, LGSDC, LGHDC 400 Aluminum Cu/Al 500 (1) (1) 1 TA350LK 630 Aluminum Cu/Al 500 kcmil () () 1 TA63L 630 Aluminum Cu/Al 500 kcmil () () 3 3TA63LK HLDDC 500 Aluminum Cu/Al 3/0 350 kcmil () () 1 TA60LD 600 Aluminum Cu/Al kcmil () () 3 3TA603LDK HMDLDC 600 Aluminum Cu/Al kcmil () 1 TA700MA1 800 Aluminum Cu/Al 3/0 400 kcmil (3) 1 TA800MA NBDC 700 Aluminum Cu/Al 3/0 400 kcmil (3) (3) 1 TA1000NB1 800 Aluminum Cu/Al 3/0 400 kcmil (3) (3) 1 TA1000NB1 900 Aluminum Cu/Al 3/0 400 kcmil (3) (3) 1 TA1000NB Aluminum Cu/Al 3/0 400 kcmil (3) (3) 1 TA1000NB1 100 Aluminum Cu/Al 4/0 500 kcmil (4) (4) 1 TA100NB1 Continuous Ampere Rating at 40 C Interrupting Capacity (Volts DC) Poles in Series With Without 600 Vdc HFDDC3100KL HFDDC3100KW HFDDC3150KL HFDDC3150KW HFDDC35KL HFDDC35KW JGKDC350KSG JGKDC350KSW HJDDC350K HJDDC350KW HKDDC3400K HKDDC3400KW 65 3 LGKDC3400KSG LGKDC3400KSW LGKDC3630KSG LGKDC3630KSW 35 3 HLDDC3600K HLDDC3600WK HMDLDC3800K HMDLDC3800WK 500 Vdc EGK3100KSG EGK3100KSW 50 Vdc HFDDC100KL HFDDC100KW HFDDC150KL HFDDC150KW 5 50 HFDDC5KL HFDDC5KW HLDDC100K 1 HLDDC100WK 1 V4-T-356 Volume 4 Circuit Protection CA E August 016

7 Molded Case Circuit s Specialty s.6 Accessories Amperes End Cap Terminals For Use with Ring Terminals External Accessories Padlockable Handle Lock Hasp Wire AWG Wire (No. s) E F/E FM 100 Cu/AI #14 1/0 (1) 3T100FB (package of three) 150 Cu #4 4/0 (1) 3T150FB (package of three) E J/E JM 50 Cu #4 350 (1) T50KB E K/E KM/E KW 5 Cu #3 350 (1) T300K 350 Cu (1) T350K 400 Cu /0 50 () 3T400K (three-pole kit) E LME/E LMZ 400 Cu/AI (1) 3TA631LK E L/E LM/E LW 400 Cu/AI 4/0 600 (1) 3TA401LDK (three-pole kit) 600 Cu () T60LD E M/E MM/E MW 600 Cu () /0 500 kcmil T600MA1 600 Cu/AI () kcmil TA700MA1 800 std. Cu/AI (3) 3/0 400 kcmil TA800MA 800 Cu/AI () kcmil TA801MA 800 Cu (3) 3/0 300 kcmil T800MA1 E N/E NM 700 Cu /0 500 () T700NB Cu 3/0 500 (3) T1000NB1 100 Cu 3/0 400 (4) T100NB Cu/AI (4) TA1600RD 000 Cu/AI 600 (6) TA000RD Amperes Metric E F/E FM 150 KPEK1 KPEMK1 E J/E JM 50 KPEK KPEMK E K/E KM/E KW 400 KPEK3 KPEMK3 E LME/E LMZ 400 L3RTWK E L/E LM/E LW 600 KPEK4 KPEMK4 E F/E FM E J/E JM E K/E KM/E KW E LME/E LMZ E L/E LM/E LW E M/E MM/E MW E N/E NM E R/E RM PLK1 PLK3 PLK3 LPHL HLK4 HLK4 PLK5 HLK6 Imperial Volume 4 Circuit Protection CA E August V4-T-391