INSPIRE 1. Quick Start Guide V1.4

Transcription

1 INSPIRE Quick Start Guide V.4

2 INSPIRE The Inspire is a professional aerial filaking and photography platfor that is ready to fly right out of the box. Featuring an onboard caera equipped with a 0 lens and -axis stabilized gibal, it shoots sharp p stills and stable video at up to 4K. Its retractable landing gear pulls up out of view, giving the caera an unobstructed 60 degree view of the world below. An advanced flight controller akes the Inspire stable, safe and easy to fly indoors or out. The brand new Vision Positioning Syste gives it the power to hover in position at low altitudes even without GPS. Like all DJI flight controllers, it is also able to return hoe if reote controller signal is lost or if the low battery warning is triggered. The Inspire boasts a axiu flight speed /s* and a axiu flight tie of 8 inutes* using one fully charged 4500Ah Intelligent Flight Battery Travel Mode Flight Mode Landing Gear Up Landing Gear Down Landing Mode. Gibal and Caera 9. Intelligent Flight Battery. Caera Micro-SD Card Slot 0. Power Button. Vision Positioning Syste. Battery Level Indicators 4. Transforation Mechanis. Aircraft Status Indicator 5. Front LEDs. Aircraft Micro-USB Port 6. Motors 4. Caera Micro-USB Port 7. Propellers 5. Gibal Lock 8. Rear LEDs * Please note that axiu flight speed and axiu run tie were tested in a lab environent. These statistics are for reference only, as conditions in your area ay vary.

3 Reote Controller The axiu transission distance of the Inspire reote controller is k*. The reote controller also allows you to control the landing gear or activate Return to Hoe with a tap. Other buttons allow instant photo capture, video recording, picture review and gibal control. A DJI Lightbridge-based HD video downlink is built-in, letting you see what your caera sees on your obile device in real tie HD. The app also allows you to change caera settings and activate Master/Slave ode so that one person can fly while other controls the gibal independently. The aster and slave controllers counicate using a 5.8Ghz wireless signal, and have a counication range with each other of up to 50 eters.the controller s LiPo battery has a axiu run tie of approxiately four hours and can be charged by plugging directly into the controller.. Power Button. Transforation Switch. Return to Hoe (RTH) Button 4. Control Sticks 5. Status LED 6. Battery Level LEDs 7. Power Port 8. Mobile Device Holder 9. Antennas 0. Handle Bar 8 9 Folded Gibal Dial 0 6. Caera Settings Dial. Video Recording Button 4. Flight Mode Switch 7 5. Shutter Button 6. Playback Button 7. Mini-HDMI Port 8. Micro-USB Port 9. CAN-Bus Port 0. USB Port. Back Buttons (Reserved) Connect to the obile device * Please note that the ax transission distance were tested in a lab environent. This statistic is for reference only, as conditions in your area ay vary.

4 Fly Safe Calibrating the Copass: Make sure to calibrate the copass in every new flight location. The copass is very sensitive to electroagnetic interference, which can cause abnoral copass data leading to poor flight perforance or even failure. Regular calibration is required for optiu perforance. Recalibrate the copass when: a) The Aircraft Status Indicator is blinking red and yellow. b) Flying in a new location. DO NOT calibrate your copass where there is a chance of strong agnetic interference, such as agnetite, parking structures, and steel reinforceents underground. DO NOT carry ferroagnetic aterials with you during calibration such as keys or cellular phones. DO NOT calibrate beside assive etal objects. If the Flight Status LED is showing solid red, then try to calibrate again. If it is blinking red and yellow alternately after placing the aircraft on the ground, the copass has detected agnetic interference. Change your location. P Mode: Safe to fly. In this ode, the Inspire has a strong GPS signal and can use the Vision Positioning Syste allowing it to hover accurately in position indoors and out. If outdoors, this ode also eans that a Hoe Point has been locked so that it can Return to Hoe if the control signal is lost. GPS Positioning If you are not in this ode, toggle the Flight Mode Switch to P position to enable it. The Flight Mode Switch is locked in P ode by default. Refer to the User Manual on how to unlock the switch. There are three states in P ode. P-GPS: GPS works best when outdoors in a wide open area, and your Inspire uses GPS to hover in place when the GPS signal is strong. P-OPTI: If GPS is not available, the aircraft can use the Vision Positioning Syste to hover accurately. P-ATTI: Neither GPS or Vision Positioning Syste available, aircraft is using only its baroeter for positioning, so only altitude is controlled. Note that the Vision Positioning Syste ay not work properly when the Inspire is flying over water, over surfaces without a clear pattern, or in a low light environent. Vision Positioning Altitude.5 Return to Hoe: Return to hoe When the GPS signal is strong, the aircraft will be able to record a Hoe Point and return to the Hoe Point when needed. The GPS location is recorded when the GPS signal icon in the DJI GO app is either yellow or green. The aircraft will return to the Hoe Point autoatically in the following cases (all require a strong GPS signal). Sart RTH: When you press the RTH button on the reote controller or in the App. Low Battery RTH: The DJI GO app notifies users to take action when the battery level falls to a specified threshold. Failsafe RTH: When the reote controller signal is lost. While returning hoe, its altitude can be adjusted by the user to avoid obstructions. Tall buildings ay affect the reote controller signal. The Failsafe Return to Hoe procedure will be triggered if the signal is lost. Be sure fly higher than any nearby buildings to avoid crashing. Flight Liits: The Inspire is not peritted to fly within no-fly zones as specified by local laws and regulations. Please visit here: for ore inforation. Environental Considerations:. Do not fly in severe weather conditions. This includes high wind, snow, rain and sog.. Only fly in open areas. Tall buildings and steel structures ay affect the accuracy of the onboard copass and GPS signal.. Avoid fro obstacles, crowds, high voltage power lines, trees or bodies of water. 4. Miniize electroagnetic interference by not flying in areas with high levels of electroagnetis, including obile phone base stations or radio transission towers. 5. Aircraft and battery perforance is subject to environental factors such as air density and teperature. Be very careful when flying 4700 feet (4500 eters) or ore above sea level as battery and aircraft perforance ay be reduced. 6. The Inspire cannot operate in P ode or use GPS at polar latitudes. It only can fly in ATTI ode and use the Vision Positioning Syste.

5 Appendix 95 g 400 g 5 5 /s 4 /s /s (ATTI ode, no wind) 4500 Approxiately 8 inutes -0 C to 40 C Gibal (Model: ZENMUSE X) Angular Vibration Range ±0.0 Controllable Range Pitch: -90 to +0 Pan: ±0 Max Controllable Speed Pitch: 0 /s Pan: 80 /s Vision Positioning Velocity Range Altitude Range Operating Environent Operating Range 45 0 Aircraft (Model: T600) Weight (Battery Included) Maxiu Weight of Payload Max Tilt Angle Max Ascent Speed Max Descent Speed Max Speed Max Altitude Above Sea Level Max Flight Tie Operating Teperature Range 8 4 <8 /s (Altitude ) 5 c-500 c Surface with clear pattern and adequate lighting (Lux > 5) 0-50 c Caera (Nae/Model: X/FC50) Sensor Sony EXMOR /. Effective pixels:.4m (total pixels:.76m) Lens FOV (Field Of View) 94 0 (5 forat equivalent) f/.8 ISO Range (video) (photo) Electronic Shutter Speed 8 s-/8000 s Iage Max Size 4000x000 Still Photography Modes Single shoot; Burst shooting: /5/7 fraes Auto Exposure Bracketing (AEB): /5 bracketed fraes at 0.7EV Bias; Tie-lapse Video Recording Modes UHD (4K): 4096x60p 4/5, 840x60p 4/5/0 FHD: 90x080p 4/5/0/48/50/60 HD: 80x70p 4/5/0/48/50/60 Max Bitrate Of Video Storage 60 Mbps Supported File Forats FAT/exFAT Photo: JPEG, DNG Video: MP4/MOV (MPEG-4 AVC/H.64) Supported SD Card Types Micro SD, Max capacity: 64GB. Class 0 or UHS- rating required Operating Teperature Range 0 C to 40 C Reote Controller (Nae: C) Operating Frequency Transitting Distance Video Output Port Operating Teperature Range Battery Intelligent Flight Battery (Model: TB47, Standard) Capacity 4500 Ah Voltage. V Battery Type LiPo 6S High voltage battery Energy 99.9 Wh Net Weight 570 g Operating Tege -0 C to 40 C Max Charging Power 80 W Intelligent Flight Battery (Model: TB48, Optional) Capacity 5700 Ah Voltage.8 V Battery Type LiPo 6S High voltage battery Energy 9.6 Wh Net Weight 670 g Operating Tege -0 C to 40 C Max Charging Power 80 W This Quick Start Guide is subject to change without prior notice. 8 Charger (Model: A4-00PA) Voltage 6. V Rated Power 00 W 9.7 MHz-97.7 MHz (Japan only) 5.75 GHz-5.85 GHz.400 GHz-.48 GHz k (outdoor and unobstructed) USB, Mini-HDMI -0 C to 40 C 6000 Ah LiPo S FCC ID SS-WM6040 FCC ID SS-GL65850 This device coplies with part 5 of the FCC Rules. Operation is subject to the following two conditions: () This device ay not cause harful interference, and () this device ust accept any interference received, including interference that ay cause undesired operation. YC.BZ.S000

6 Using INSPIRE Watch the video tutorials on the official DJI website and read the following docuents before using your Inspire for the first tie: Inspire Quick Start Guide, Disclaier, Intelligent Flight Battery Safety Guidelines, Inspire Safety Guidelines, In the Box, Inspire User Manual.. Download the DJI GO App. Watch the Tutorial Videos Search DJI GO on the App Store or Google Play and download the app to your obile device. Watch the tutorial videos at or in the DJI GO app. DJI GO app The tutorial videos For the best user experience, please use obile devices with ios 8.0 (or higher) and Android 4.. (or higher). Read the Inspire User Manual in the DJI GO app or official DJI website for ore details.. Check Battery Levels Press the Power Button once on both the Intelligent Flight Battery and reote controller to check battery levels. The Intelligent Flight Battery ust be fully charged before using it for the first tie. Make sure both batteries are adequately charged before each flight. Press the power button once then press again and hold for seconds to power on the reote controller. Repeat to power off. Press the power button once, then press again and hold for seconds to power on the Intelligent Flight Battery. Repeat to power off. High Battery Level Low Battery Level High Low 4. Charging Only use the official DJI Inspire charger for your Intelligent Flight Battery and reote controller. To charge the Inspire Intelligent Flight Battery or the reote controller, connect it to power through the port to a suitable power source (00-40V 50/60Hz). It is recoended to turn off the batteries before charging. Use the included charger to charge the Intelligent Flight Battery and the reote controller battery. When fully charged, the battery LEDs on the Intelligent Flight Battery and reote controller will turn off. A B A B

7 5. Preparing the Reote Controller Tilt the Mobile Device Holder to the desired position then adjust the antennas as shown. The strength of the reote controller signal is different when the antenna position is different. Strong Weak The transission signal between the aircraft and reote controller will perfor best when within the optial transission range. If the signal is weak, fly the aircraft closer to you to achieve optial signal perforance. Press the button on the side of the Mobile Device Holder to release the clap. Place your device onto the clap and adjust the clap to hold it securely. Connect your obile device to the reote controller with a USB cable. Plug one end of the cable into your obile device, and the other end into the USB port on the back of the reote controller. If you have purchased an Inspire with dual reote controllers, the Master reote controller will connect to the aircraft autoatically when powered on. Master/Slave ode is disabled by default. Activate it and set it up through the DJI GO app. The Master reote controller s Status LED will show solid green when it connected to the aircraft. The Slave reote controller s Status LED will show solid blue when it is connected to the Master controller. Connecting the Master reote controller to the Slave reote controller: On the Master reote controller, launch the DJI GO app and go to the Caera page. Then tap on the top of your screen to enter the reote controller settings window. Tap Activate Master/Slave Mode and select Master. Then enter your desired connection password for the Slave reote controller. On the Slave reote controller, select Slave and tap Search to find the Master reote controller. Select the Master reote controller fro the Master RC List and input the connection password. Do not use other.4ghz devices at the sae tie to avoid signal interference. 6. Preparing the Aircraft The aircraft is in Travel Mode during delivery. Follow these steps to change it to Landing Mode before your first flight: Insert the Intelligent Flight Battery into the battery copartent. Power on the reote controller and the Intelligent Flight Battery. Toggle the Transforation Switch up and down at least four ties. Repeat to change aircraft to Travel Mode. Power off the aircraft before ounting the gibal and caera. Travel Mode Landing Mode If you have purchased the dual reote controller version, you ust use the Master reote controller to deactivate Travel Mode.

8 7. Mounting the Gibal and Caera Reove the Gibal Cover. Rotate the Gibal Lock to the unlocked position (to the right when facing the nose of the aircraft). Insert the gibal by aligning the white ark on the gibal with white ark on the Gibal Lock. Rotate the gibal lock back into the locked position (to the left when facing the nose of the aircraft). Gibal Cover Gibal Lock Mounting Place Gibal Connector Locked 8. Preparing for Flight Place the aircraft on a flat surface, in an open space, with the back facing you. Move the Flight Mode Switch to the right to select P ode. ( P ode is Positioning ode, A ode is ATTI ode, and the F ode is Function ode. ) Power on the reote controller. Power on the aircraft and wait for the self-check to coplete. Do not ove the aircraft during the self-check. Ensure the reote controller is linked to the aircraft before flight. Re-link the reote controller to the aircraft if it fails to connect. Refer to the INSPIRE User Manual on how to link. 5 Ensure the reote controller and your obile device are connected with a USB cable. Launch the DJI GO app when connecting to the aircraft for the first tie, and follow the instructions within the app. 6 Launch the DJI GO app and tap Caera. Ensure the aircraft is functioning norally by copleting the Checklist.Beginner Mode is enabled by default when you launch the DJI GO app for the first tie. The aircraft s altitude and flight distance is restricted when flying in Beginner Mode. We recoend you fly in Beginner Mode when using the aircraft for the first tie. You ay disable Beginner Mode in the settings page of the DJI GO app. 7 Calibrate the copass by tapping the Aircraft Status Bar in the app and selecting Calibrate. Then follow the on-screen instructions. 8 For 45s Propeller, install the propellers with a white dot onto the ounting plates that have a white dot, and install the propellers without a white dot onto the ounting plates that do not have a white dot. Press the propeller down onto the ounting plate and rotate in the lock direction until secure. For 45 Propeller, attach propellers with the black nut onto otors with the black dot and spin counter-clockwise to secure. Attach propellers with gray nut onto otors without a black dot and spin clockwise to secure. Place all propellers onto the correct otor and tighten by hand to ensure security before flight DJI GO App 7 8 When not in P ode, the Inspire will only aintain altitude, not position, and will drift with wind or user inputs. Return to Hoe is not available in F ode. 9. Reote Controller Operation The reote controller is by default set to Mode ( throttle controlled by the left-hand stick ). Adjust the tilt angle of caera by using the Gibal Dial. Left Stick Right Stick UP Forward Left Turn Left B a ck w ard UP Forward Left Turn Left Right Turn Right Down Right Turn Right Down B a ck w ard You can set the reote controller to different odes using the DJI GO app. Gibal Dial

9 0. Flight Auto Taking - Off & Landing: Safe to Fly (GPS) ( In the Caera screen of the DJI GO app ) Before taking off, ake sure the aircraft status bar in the DJI GO app shows Safe to Fly (GPS). Otherwise, the aircraft cannot hover in place and record the Hoe Point. Tap and confir your selection. The aircraft will autoatically take off, retract its landing gear, and hover at. eters after you tap and confir Auto Take-off. Tap and confir your selection. The landing gear will lower and the aircraft will autoatically land. Manual Take - off & Landing Return to Hoe Start the otors by pulling both control sticks to the botto inside (or outside) corners. Release the sticks once the otors start. Slowly push the left (throttle) stick up to take off. Once in the air, toggle the Transforation Switch up to raise the landing gear. Toggle the Transforation Switch up Start / Stop the otors RTH Button. Press and hold the return hoe button until the LED surrounding the button is blinking white, and the return hoe procedure is in process. Press once to stop the procedure. OR Left stick / Up (Slowly) Gently pull the left (throttle) stick down to lower the aircraft until it touches the ground. Pull both sticks to the botto inside corners to stop the otors. After flight, change the aircraft back into Travel Mode. Do not attept this at the beach, over grass, or over onochroatic carpet. Then place the aircraft on a flat surface and reove the gibal and caera for transport. Reote Controller Status LED Aircraft Status Indicator Description Slowly: Safe to fly,gps working X. The DJI GO app notifies users to take action when the battery level falls to a specified threshold. This warning threshold can be set within the DJI GO app. The aircraft will land iediately when it reaches Critical Low Battery Level Warning. Left stick / Down (Slowly) It is highly recoended that you only take off when the Aircraft Status bar is green. The aircraft cannot take off if the Critical Low Battery Warning is active. The Intelligent Flight Battery ust war-up if the outside teperature is low. A warning will display in the DJI GO app. Rotating propellers can be dangerous. Do not start the otors when there are people nearby and always fly in a wide open area. Never stop the otors during flight. Power off the aircraft prior to switching off the reote controller after landing. Appendix Double: Vision Positioning Syste working, no GPS. Failsafe: The Inspire will enter RTH ode if reote controller signal is lost. user to avoid obstructions. Using the Caera Slowly: P-ATTI or ATTI Quickly: Not connected to reote controller B-B-B... Aircraft low battery warning or reote controller error. B B... Reote controller has been idle for 5 inutes. Quickly: Critical low battery level warning Slowly: Low battery level warning Adjust the caera paraeters using the Caera Settings Dial on the reote controller or through the DJI GO app. Press the Shutter Button/Video Record Reote controller is functioning norally and is connected to the aircraft. Reote controller is in Slave Mode and is connected to the aircraft. While returning hoe, its altitude can be adjusted by the Reote controller is functioning norally but is not connected to the aircraft. Reote controller is in Slave Mode and not connected to the aircraft. The App s RTH Button Button to capture photos or record videos. Adjust the tilt of the gibal using the Gibal Dial. Download photos and video fro the SD card to your obile device through the DJI GO app. You ay also use a SD card reader to export files to your PC. Solid: Critical error Learn ore inforation fro: Blinking Alternately: Copass calibration required 04 DJI. All Rights Reserved Designed by DJI. Printed in China.

10 INSPIRE Creativity Unleashed