Principles of Doubly-Fed Induction Generators (DFIG)

Transcription

1 Renewable Energy Principles of Doubly-Fed Induction Generators (DFIG) Courseware Sample F0 A

2

3

4 RENEWABLE ENERGY PRINCIPLES OF DOUBLY-FED INDUCTION GENERATORS (DFIG) Courseware Sample by the staff of Lab-Volt Ltd. Copyright 2011 Lab-Volt Ltd. All rights reserved. No part of this publication may be reproduced, in any form or by any means, without the prior written permission of Lab-Volt Ltd. Printed in Canada May 2011

5 Foreword Doubly-fed electric machines are basically electric machines that are fed ac currents into both the stator and the rotor windings. Most doubly-fed electric machines in industry today are three-phase wound-rotor induction machines. Although their principles of operation have been known for decades, doubly-fed electric machines have only recently entered into common use. This is due almost exclusively to the advent of wind power technologies for electricity generation. Doubly-fed induction generators (DFIGs) are by far the most widely used type of doubly-fed electric machine, and are one of the most common types of generator used to produce electricity in wind turbines. Doubly-fed induction generators have a number of advantages over other types of generators when used in wind turbines. The primary advantage of doubly-fed induction generators when used in wind turbines is that they allow the amplitude and frequency of their output voltages to be maintained at a constant value, no matter the speed of the wind blowing on the wind turbine rotor. Because of this, doubly-fed induction generators can be directly connected to the ac power network and remain synchronized at all times with the ac power network. Other advantages include the ability to control the power factor (e.g., to maintain the power factor at unity), while keeping the power electronics devices in the wind turbine at a moderate size. This manual covers the operation of doubly-fed induction generators, as well as their use in wind turbines. It also covers the operation of three-phase wound-rotor induction machines used as three-phase synchronous machines and doubly-fed induction motors. Although it is possible to use these machines by themselves, they are primarily studied as a stepping stone to doubly-fed induction generators. Doubly-fed induction generators are commonly used in wind turbines to generate large amounts of electrical power. A Principles of Doubly-Fed Induction Generators (DFIG) v

6

7 Table of Contents Introduction Principles of Doubly-Fed Induction Generators (DFIG)... 1 Doubly-fed electric rotating machines. Exercise 1 Three-Phase Wound-Rotor Induction Machine Used as a Synchronous Machine... 3 Three-phase wound-rotor induction machine used as a synchronous machine. Feeding dc current into the windings of a three-phase wound-rotor induction machine. Exercise 2 Doubly-Fed Induction Motors Doubly-fed induction motor operation. Exercise 3 Doubly-Fed Induction Generators Doubly-fed induction generator operation. Using doubly-fed induction generators to produce fixed-frequency voltages. Doubly-fed induction generators used in wind turbines. Appendix A Equipment Utilization Chart Appendix B Glossary of New Terms Appendix C Impedance Table for the Load Modules Appendix D Circuit Diagram Symbols Index of New Terms Bibliography We Value Your Opinion! A Principles of Doubly-Fed Induction Generators (DFIG) vii

8

9 Sample Exercise Extracted from Student Manual

10

11 Exercise 3 Doubly-Fed Induction Generators EXERCISE OBJECTIVE When you have completed this exercise, you will be familiar with the operation of three-phase wound-rotor induction machines used as doubly-fed induction generators. You will also know how doubly-fed induction generators are used in wind turbines to generate large amounts of electrical power. DISCUSSION OUTLINE The Discussion of this exercise covers the following points: Doubly-fed induction generator operation Using doubly-fed induction generators to produce fixed-frequency voltages Doubly-fed induction generators used in wind turbines DISCUSSION From now on, a three-phase wound-rotor induction machine operating as a doublyfed induction generator will be referred to simply as a doubly-fed induction generator. Doubly-fed induction generator operation As seen in Exercise 2, a three-phase wound-rotor induction machine can be set up as a doubly-fed induction motor. In this case, the machine operates like a synchronous motor whose synchronous speed (i.e., the speed at which the motor shaft rotates) can be varied by adjusting the frequency of the ac currents fed into the rotor windings. The same wound-rotor induction machine setup can also serve as a doubly-fed induction generator. In this case, mechanical power at the machine shaft is converted into electrical power supplied to the ac power network via both the stator and rotor windings. Furthermore, the machine operates like a synchronous generator whose synchronous speed (i.e., the speed at which the generator shaft must rotate to generate power at the ac power network frequency ) can be varied by adjusting the frequency of the ac currents fed into the rotor windings. The remainder of this exercise discussion deals with the operation of three-phase wound-rotor induction machines used as doubly-fed induction generators. In a conventional three-phase synchronous generator, when an external source of mechanical power (i.e., a prime mover) makes the rotor of the generator rotate, the static magnetic field created by the dc current fed into the generator rotor winding rotates at the same speed ( ) as the rotor. As a result, a continually changing magnetic flux passes through the stator windings as the rotor magnetic field rotates, inducing an alternating voltage across the stator windings. Mechanical power applied to the generator shaft by the prime mover is thus converted to electrical power that is available at the stator windings. In conventional (singly-fed) induction generators, the relationship between the frequency of the ac voltages induced across the stator windings of the generator and the rotor speed is expressed using the following equation. A Principles of Doubly-Fed Induction Generators (DFIG) 33

12 Exercise 3 Doubly-Fed Induction Generators Discussion = 120 (3) where is the frequency of the ac voltages induced across the stator windings of the doubly-fed induction generator, expressed in hertz (Hz). is the speed of the doubly-fed induction generator rotor, expressed in rotations per minute (r/min). is the number of poles in the doubly-fed induction generator per phase. Using Equation (3), it is possible to determine that, when the speed of the generator rotor is equal to the generator synchronous speed, the frequency of the ac voltages induced across the stator windings of the generator is equal to the frequency of the ac power network. The same operating principles apply in a doubly-fed induction generator as in a conventional (singly-fed) induction generator. The only difference is that the magnetic field created in the rotor is not static (as it is created using three-phase ac current instead of dc current), but rather rotates at a speed, proportional to the frequency of the ac currents fed into the generator rotor windings. This means that the rotating magnetic field passing through the generator stator windings not only rotates due to the rotation of the generator rotor, but also due to the rotational effect produced by the ac currents fed into the generator rotor windings. Therefore, in a doubly-fed induction generator, both the rotation speed of the rotor and the frequency of the ac currents fed into the rotor windings determine the speed, of the rotating magnetic field passing through the stator windings, and thus, the frequency of the alternating voltage induced across the stator windings. Taking into account the principles of operation of doubly-fed induction generators, it can thus be determined that, when the magnetic field at the rotor rotates in the same direction as the generator rotor, the rotor speed and the speed, of the rotor magnetic field (proportional to ) add up. This is shown in Figure 10a. The frequency of the voltages induced across the stator windings of the generator can thus be calculated using the following equation: = (4) where is the frequency of the ac currents fed into the doubly-fed induction generator rotor windings, expressed in hertz (Hz). Conversely, when the magnetic field at the rotor rotates in the direction opposite to that of the generator rotor, the rotor speed and the speed, of the rotor magnetic field subtract from each other. This is shown in Figure 10b. The frequency of the voltages induced across the stator windings of the generator can thus be calculated using the following equation: = 120 (5) 34 Principles of Doubly-Fed Induction Generators (DFIG) A

13 Exercise 3 Doubly-Fed Induction Generators Discussion, = +, Mechanical power Resulting magnetic field in the stator Rotor magnetic field (, ) Rotor speed ( ) Mechanical power AC currents ( ), =, AC currents ( ) Rotor Stator (a) Variable-frequency ac currents ( ) Variable-frequency ac currents ( ) When the stator and rotor magnetic fields rotate in the same direction Figure 10. Interaction between the rotor speed and the frequency of the rotating magnetic field created in the rotor windings of a doubly-fed induction generator. (b) When the stator and rotor magnetic fields rotate in opposite directions In other words, the frequency of the ac voltages produced at the stator of a doubly-fed induction generator is proportional to the speed, of the rotating magnetic field at the stator. The speed, of the stator rotating magnetic field itself depends on the rotor speed (resulting from the mechanical power at the rotor shaft) and the frequency of the ac currents fed into the machine rotor. Using doubly-fed induction generators to produce fixed-frequency voltages The primary reason for using a doubly-fed induction generator is generally to produce three-phase voltage whose frequency is constant, i.e., whose frequency remains equal to the frequency of the ac power network to which the generator is connected, despite variations in the generator rotor speed caused by fluctuations of the mechanical power provided by the prime mover (e.g., a wind turbine rotor) driving the generator. To achieve this purpose, the frequency of the ac currents fed into the rotor windings of the doubly-fed induction generator must be continually adjusted to counteract any variation in the rotor speed caused by fluctuations of the mechanical power provided by the prime mover driving the generator. The frequency of the ac currents that need to be fed into the doubly-fed induction generator rotor windings to maintain the generator output frequency at the same value as the frequency of the ac power network depends on the rotation speed of the generator rotor, and can be calculated using the following equation: A Principles of Doubly-Fed Induction Generators (DFIG) 35

14 Exercise 3 Doubly-Fed Induction Generators Discussion = 120 (6) where is the frequency of the ac currents that need to be fed into the doubly-fed induction generator rotor windings for to be equal to, expressed in hertz (Hz). is the frequency of the ac power network to which the doublyfed induction generator is connected, expressed in hertz (Hz). is the rotational speed of the generator rotor, expressed in rotations per minute (r/min). is the number of magnetic poles per phase in the doubly-fed induction generator. Using Equation (6), it is possible to calculate that, if the generator rotor rotates at the nominal (singly-fed) synchronous speed, the frequency of the ac currents that need to be fed into the generator rotor windings will be equal to 0 Hz (i.e., dc current). The machine would thus operate as a conventional (singly-fed) three-phase synchronous machine. When the generator rotor speed decreases below the nominal synchronous speed, the frequency of the ac currents that need to be fed into the generator windings increases accordingly and is of positive polarity. The positive polarity of the frequency indicates that the phase sequence of the three-phase ac currents fed into the rotor windings must make the rotor magnetic field rotate in the same direction as the generator rotor, as is illustrated in Figure 10a. Similarly, when the generator rotor speed increases above the nominal synchronous speed, the frequency of the ac currents that need to be fed into the generator windings increases accordingly and is of negative polarity. The negative polarity of the frequency indicates that the phase sequence of the three-phase ac currents fed into the rotor windings must make the rotor magnetic field rotate in the direction opposite to that of the generator rotor, as is illustrated in Figure 10b. For example, consider a doubly-fed induction generator having 4 magnetic poles. The generator supplies power to a 60 Hz ac power network. Considering that an external source makes the generator rotate at a speed of 1980 r/min, the frequency of the ac currents that need to be fed into the generator rotor windings can be calculated so: = r/min 4 poles = 60 Hz = 6 Hz 120 The frequency of the ac currents to be fed into the generator rotor windings so that the frequency of the generator output voltage is equal to the frequency of the ac power network is 6 Hz. The negative polarity of the frequency indicates that the magnetic field created in the rotor windings must rotate in the direction opposite to the direction of the rotor. When a doubly-fed induction generator is used to produce power at the ac power network voltage and frequency, any deviation of the generator rotor speed from the synchronous speed is compensated by adjusting the frequency 36 Principles of Doubly-Fed Induction Generators (DFIG) A

15 Exercise 3 Doubly-Fed Induction Generators Discussion of the ac currents fed into the generator rotor windings so that the frequency of the voltage produced at the stator remains equal to the ac power network frequency. In other words, the frequency is adjusted so that the speed, of the rotating magneting field passing through the stator windings remains constant. Consequently, to maintain the voltage produced at the stator equal to the ac power network voltage, a specific magnetic flux value must be maintained in the machine (more precisely at the stator windings). This can be achieved by applying a voltage to the generator rotor windings that is proportional to the frequency of the voltages applied to the rotor windings (this maintains the ratio constant and ensures a constant magnetic flux value in the machine). The value of the ratio is generally set so that the reactive power at the stator is equal to zero. This is similar to the common practice used with conventional (singly-fed) synchronous generators where the exciter current (dc current in the rotor) is adjusted so as to zero the reactive power at the stator. Doubly-fed induction generators used in wind turbines Most doubly-fed induction generators in industry today are used to generate electrical power in large (power-utility scale) wind turbines. This is primarily due to the many advantages doubly-fed induction generators offer over other types of generators in applications where the mechanical power provided by the prime mover driving the generator varies greatly (e.g., wind blowing at variable speed on the bladed rotor of a wind turbine). To better understand the advantages of using doubly-fed induction generators to generate electrical power in wind turbines, however, it is important to know a little about large-size wind turbines. Large-size wind turbines are basically divided into two types which determine the behavior of the wind turbine during wind speed variations: fixed-speed wind turbines and variable-speed wind turbines. In fixed-speed wind turbines, threephase asynchronous generators are generally used. Because the generator output is tied directly to the grid (local ac power network), the rotation speed of the generator is fixed (in practice, it can generally vary a little as the slip is allowed to vary over a range of typically 2% to 3%), and so is the rotation speed of the wind turbine rotor. Any fluctuation in wind speed naturally causes the mechanical power at the wind turbine rotor to vary and, because the rotation speed is fixed, this causes the torque at the wind turbine rotor to vary accordingly. Whenever a wind gust occurs, the torque at the wind turbine rotor thus increases significantly while the rotor speed varies little. Therefore, every wind gust stresses the mechanical components (notably the gear box) in the wind turbine and causes a sudden increase in rotor torque, as well as in the power at the wind turbine generator output. Any fluctuation in the output power of a wind turbine generator is a source of instability in the power network to which it is connected. In variable-speed wind turbines, the rotation speed of the wind turbine rotor is allowed to vary as the wind speed varies. This precludes the use of asynchronous generators in such wind turbines as the rotation speed of the generator is quasi-constant when its output is tied directly to the grid. The same is true for synchronous generators which operate at a strictly constant speed when tied directly to the grid. This is where doubly-fed induction generators come into play, as they allow the generator output voltage and frequency to be maintained at constant values, no A Principles of Doubly-Fed Induction Generators (DFIG) 37

16 Exercise 3 Doubly-Fed Induction Generators Discussion matter the generator rotor speed (and thus, no matter the wind speed). As seen in the previous section, this is achieved by feeding ac currents of variable frequency and amplitude into the generator rotor windings. By adjusting the amplitude and frequency of the ac currents fed into the generator rotor windings, it is possible to keep the amplitude and frequency of the voltages (at stator) produced by the generator constant, despite variations in the wind turbine rotor speed (and, consequently, in the generator rotation speed) caused by fluctuations in wind speed. By doing so, this also allows operation without sudden torque variations at the wind turbine rotor, thereby decreasing the stress imposed on the mechanical components of the wind turbine and smoothing variations in the amount of electrical power produced by the generator. Using the same means, it is also possible to adjust the amount of reactive power exchanged between the generator and the ac power network. This allows the power factor of the system to be controlled (e.g., in order to maintain the power factor at unity). Finally, using a doubly-fed induction generator in variable-speed wind turbines allows electrical power generation at lower wind speeds than with fixed-speed wind turbines using an asynchronous generator. It would be possible to obtain similar results in variable-speed wind turbines using a three-phase synchronous generator and power electronics, as shown in Figure 11a. In this setup, the generator rotates at a speed that is proportional to the wind speed. The ac currents produced by the generator are converted into dc current by an AC/DC converter, then converted by another AC/DC converter back to ac currents that are synchronous with the ac power network. It is therefore necessary for the power electronics devices used in such a circuit to have the size and capacity to process 100% of the generator output power. The power electronics devices used in doubly-fed induction generators, on the other hand, need only to process a fraction of the generator output power, i.e., the power that is supplied to or from the generator rotor windings, which is typically about 30% of the generator rated power. Consequently, the power electronics devices in variable-speed wind turbines using doubly-fed induction generators typically need only to be about 30% of the size of the power electronics devices used for comparatively sized three-phase synchronous generators, as illustrated in Figure 11b. This reduces the cost of the power electronics devices, as well as the power losses in these devices. 38 Principles of Doubly-Fed Induction Generators (DFIG) A

17 Exercise 3 Doubly-Fed Induction Generators Discussion Variable voltage and frequency ac current AC/DC converter AC/DC converter Synchronized ac current DC current Three-phase synchronous generator To ac power network (a) Three-phase synchronous generator Doubly-fed induction generator Synchronized ac current To ac power network AC/DC converter AC/DC converter DC current Variable voltage and frequency ac current Synchronized ac current (b) Doubly-fed induction generator Figure 11. Circuit topologies for two types of generators found in variable-speed wind turbines. To summarize, using a doubly-fed induction generator instead of an asynchronous generator in wind turbines offers the following advantages: 1. Operation at variable rotor speed while the amplitude and frequency of the generated voltages remain constant. 2. Optimization of the amount of power generated as a function of the wind available up to the nominal output power of the wind turbine generator. A Principles of Doubly-Fed Induction Generators (DFIG) 39

18 Exercise 3 Doubly-Fed Induction Generators Procedure Outline 3. Virtual elimination of sudden variations in the rotor torque and generator output power. 4. Generation of electrical power at lower wind speeds. 5. Control of the power factor (e.g., in order to maintain the power factor at unity). On the other hand, the doubly-fed induction generator requires complex power conversion circuitry which the asynchronous generator does not need. Also, the slip rings on the wound-rotor induction machine used to implement the doublyfed induction generator require periodic maintenance while no such rings are required on the rotor of the squirrel-cage induction machine used to implement the asynchronous generator. Using a synchronous generator in wind turbines offers the same advantages (see above) as when a doubly-fed induction generator is used. Both types of generator require two AC/DC converters. However, the two AC/DC converters in doubly-fed induction generators are significantly smaller than those in synchronous generators of comparable output power. This is because the AC/DC converters in doubly-fed induction generators convey only about 30% of the nominal generator output power while the AC/DC converters in synchronous generators convey 100% of the nominal generator output power. PROCEDURE OUTLINE The Procedure is divided into the following sections: Setup and connections Doubly-fed induction generator hyposynchronous operation Doubly-fed induction generator hypersynchronous operation PROCEDURE CAUTION! High voltages are present in this laboratory exercise! Do not make or modify any banana jack connections with the power on unless otherwise specified! Setup and connections In this section, you will set up a circuit containing a three-phase wound-rotor induction machine coupled to a prime mover. You will then set the measuring equipment required to study the three-phase wound-rotor induction machine operating as a doubly-fed induction generator. 1. Refer to the Equipment Utilization Chart in Appendix A to obtain the list of equipment required to perform this exercise. Install the required equipment in the Workstation. Mechanically couple the Three-Phase Wound-Rotor Induction Machine to the Four-Quadrant Dynamometer/Power Supply using a timing belt. 40 Principles of Doubly-Fed Induction Generators (DFIG) A

19 Exercise 3 Doubly-Fed Induction Generators Procedure 2. Make sure that the ac and dc power switches on the Power Supply are set to the O (off) position, then connect the Power Supply to a three-phase ac power outlet. Make sure that the main power switch on the Four-Quadrant Dynamometer/ Power Supply is set to the O (off) position, then connect its Power Input to an ac power wall outlet. Connect the Power Input of the Data Acquisition and Control Interface to a 24 V ac power supply. Connect the Low Power Input of the IGBT Chopper/Inverter to the Power Input of the Data Acquisition and Control Interface. Turn the 24 V ac power supply on. 3. Connect the USB port of the Data Acquisition and Control Interface to a USB port of the host computer. Connect the USB port of the Four-Quadrant Dynamometer/Power Supply to a USB port of the host computer. 4. Connect the equipment as shown in Figure 12. L1 Prime mover Three-phase wound-rotor induction machine L2 L3 Figure 12. Three-phase wound-rotor induction machine operating as a doubly-fed induction generator. A Principles of Doubly-Fed Induction Generators (DFIG) 41

20 Exercise 3 Doubly-Fed Induction Generators Procedure a The two AC/DC converters used to implement the doubly-fed induction generator shown in the figure above are a three-phase rectifier and a threephase PWM inverter (implemented using the IGBT Chopper/Inverter). The three-phase rectifier allows power to flow from the ac power source to the generator rotor windings only. Therefore, make sure that the Dumping switch on the IGBT Chopper/Inverter is set to the I position. This allows power that come from the generator rotor windings under certain operating conditions to be dissipated into a dump resistor integrated into the three-phase PWM inverter, as is done in many actual doubly-fed induction generators. In certain other doubly-fed induction generators, two bidirectional AC/DC converters (three-phase PWM rectifier/inverter) are used to allow power flow in both directions. This allows power coming from the generator rotor winding to be returned to the ac power source, thereby increasing the total power supplied to the source. The operation principles of the three-phase PWM rectifier/inverter, however, are beyond the scope of this manual. Connect the Digital Outputs of the Data Acquisition and Control Interface (DACI) to the Switching Control Inputs of the IGBT Chopper/Inverter using a DB9 connector cable. 5. Turn the Four-Quadrant Dynamometer/Power Supply on, then set the Operating Mode switch to Dynamometer. This setting allows the Four- Quadrant Dynamometer/Power Supply to operate as a prime mover, a brake, or both, depending on the selected function. 6. Turn the host computer on, then start the LVDAC-EMS software. In the Module Selector window, make sure that the Data Acquisition and Control Interface and the Four-Quadrant Dynamometer/Power Supply are detected. Make sure that the Computer-Based Instrumentation and Chopper/Inverter Control functions for the Data Acquisition and Control Interface are selected. Also, select the network voltage and frequency that correspond to the voltage and frequency of your local ac power network, then click the OK button to close the Module Selector window. 7. In LVDAC-EMS, open the Four-Quadrant Dynamometer/Power Supply window, then make the following settings: Set the Function parameter to Positive Constant-Torque Prime Mover/Brake. This makes the Four-Quadrant Dynamometer/Power Supply operate as a prime mover/brake with a positive (applied in cw direction) torque setting corresponding to the Torque parameter. Set the Torque parameter to 1.5 N m (8.85 lbf in). Set the Pulley Ratio parameter to 24: Principles of Doubly-Fed Induction Generators (DFIG) A

21 Exercise 3 Doubly-Fed Induction Generators Procedure 8. In LVDAC-EMS, open the Chopper/Inverter Control window, then make the following settings: Select the Three-Phase, PWM Inverter function. Set the Switching Frequency to 1000 Hz. Set the Phase Sequence to Fwd/Rev. Set the Frequency to 0.0 Hz. Set the Peak Voltage (% of DC Bus) parameter to 25%. Make sure that the to parameters are set to PWM. 9. In LVDAC-EMS, start the Metering application. Make the required settings in order to measure the doubly-fed induction generator active power at the stator and reactive power at the stator using the two-wattmeter method (meter function PQS1 + PQS2). Set another meter to measure the active power that is supplied to the motor rotor windings. Doubly-fed induction generator hyposynchronous operation In this section, you will make the doubly-fed induction generator rotate at the synchronous speed with a constant torque. You will confirm that the machine operates as a three-phase synchronous generator. You will adjust the amount of current fed into the generator rotor so that the generator reactive power at the stator is virtually equal to zero. You will then record the generator speed, mechanical power, active power at the stator, reactive power at the stator, active power at the rotor, and rotor frequency in the Data Table. You will increase the generator rotor frequency (with the same sequence at the rotor and stator) by steps of 1 Hz, each time adjusting the reactive power at the stator to 0 var, and recording the generator parameters in the Data Table. You will stop increasing the generator rotor frequency when it is no longer possible to adjust the reactive power at the stator to 0 var. 10. On the Three-Phase Wound-Rotor Induction Machine, press and hold the Protection Override push-button in order to momentarily override the overvoltage protection then, on the Power Supply, turn the three-phase ac power source on. Release the Protection Override push-button. Before starting the prime mover, make sure that the Three-Phase Wound- Rotor Induction Machine is rotating in the clockwise direction. If so, proceed directly to the next step. Otherwise, turn the three-phase ac power source off, invert the connections at two of the three phase terminals of the machine stator windings, then repeat this step from the beginning. 11. In the Chopper/Inverter Control window, start the Three-Phase, PWM Inverter. A Principles of Doubly-Fed Induction Generators (DFIG) 43

22 Exercise 3 Doubly-Fed Induction Generators Procedure In the Four-Quadrant Dynamometer/Power Supply window, start the Positive Constant-Torque Prime Mover/Brake. Is the three-phase wound-rotor induction machine now rotating at the synchronous speed, thus confirming that the machine operates as a threephase synchronous machine? Yes No Is the three-phase wound-rotor induction machine active power at the stator indicated in the Metering window positive, indicating that active power is supplied from the machine to the three-phase ac power source and thus, that the machine operates as a generator? Yes No Do your observations confirm that the three-phase wound-rotor induction machine is operating as a doubly-fed induction generator? Yes No 12. In the Chopper/Inverter Control window, adjust the value of the Peak Voltage (% of DC Bus) parameter until the doubly-fed induction generator reactive power at the stator is virtually equal to 0 var. 13. In LVDAC-EMS, open the Data Table window. Set the Data Table to record the doubly-fed induction generator speed, and mechanical power indicated in the Four-Quadrant Dynamometer/Power Supply window. Also, set the Data Table to record the doubly-fed induction generator active power at the stator, reactive power at the stator, and active power at the rotor indicated in the Metering application. Finally, set the Data Table to record the frequency of the ac currents fed into the rotor of the doubly-fed induction generator. 14. In the Data Table, click on the Record Data button to record the current values of the doubly-fed induction generator speed, mechanical power, active power at the stator, reactive power at the stator, active power at the rotor, and rotor frequency. 15. In the Chopper/Inverter Control window, increase the Frequency parameter by 1.0 Hz. Adjust the value of the Peak Voltage (% of DC Bus) parameter until the doubly-fed induction generator reactive power at the stator is virtually equal to 0 var. 44 Principles of Doubly-Fed Induction Generators (DFIG) A

23 Exercise 3 Doubly-Fed Induction Generators Procedure 16. Repeat steps 14 and 15 until the doubly-fed induction generator reactive power at the stator cannot be adjusted to 0 var anymore because the Peak Voltage (% of DC Bus) parameter is at a maximum (i.e., 100%). In the Four-Quadrant Dynamometer/Power Supply window, stop the Positive Constant-Torque Prime Mover/Brake. Doubly-fed induction generator hypersynchronous operation In this section, you will set the doubly-fed induction generator rotor frequency back to 0 Hz, and make the generator rotate at the synchronous speed with a constant torque. You will adjust the generator reactive power at the stator to 0 var. You will then reverse the phase sequence of the currents fed into the rotor windings and increase the generator rotor frequency (the phase sequence at the rotor is now opposite to that at the stator) by steps of 1 Hz, each time adjusting the generator reactive power at the stator to 0 var, and recording the generator parameters in the Data Table. You will stop increasing the generator rotor frequency when it is not possible anymore to adjust the generator reactive power at the stator to 0 var, or when the maximum power output of the prime mover is reached. You will export the data to a spreadsheet, and calculate the generator total power and efficiency using the recorded generator parameters. You will also extrapolate the generator active power at the rotor when power is returned to the three-phase ac power source. You will plot the generator mechanical power, active power at the stator, active power at the rotor, and total power as a function of the generator speed on the same graph, and analyze the results. Finally, you will plot the generator efficiency as a function of the generator speed, and analyze the results. 17. In the Chopper/Inverter Control window, stop the Three-Phase, PWM Inverter, then make the following settings: Set the Frequency to 0.0 Hz. Set the Peak Voltage (% of DC Bus) parameter to 25%. Start the Three-Phase, PWM Inverter. In the Four-Quadrant Dynamometer/Power Supply window, start the Positive Constant-Torque Prime Mover/Brake. 18. In the Chopper/Inverter Control window, adjust the value of the Peak Voltage (% of DC Bus) parameter until the doubly-fed induction generator reactive power at the stator is virtually equal to 0 var. A Principles of Doubly-Fed Induction Generators (DFIG) 45

24 Exercise 3 Doubly-Fed Induction Generators Procedure 19. In the Chopper/Inverter Control window, decrease the Frequency parameter by 1.0 Hz. a The polarity of the Frequency parameter is negative, indicating that the phase sequence at the three-phase inverter output is reversed. Therefore, whenever the Frequency parameter is decreased (e.g., when it passes from -2.0 Hz to -3.0 Hz), the frequency of the ac currents fed into the rotor windings actually increases (e.g., it passes from 2.0 Hz to 3.0 Hz). Adjust the value of the Peak Voltage (% of DC Bus) parameter until the doubly-fed induction generator reactive power at the stator is virtually equal to 0 var. 20. In the Data Table, click on the Record Data button to record the current value of the doubly-fed induction generator speed, mechanical power, active power at the stator, reactive power at the stator, active power at the rotor, and rotor frequency. Each time you record the generator parameters on the Data Table, observe if the Dumping LED on the IGBT Chopper/Inverter turns on intermittently, indicating that power is returned from the generator rotor windings to the three-phase PWM inverter and then dumped in capacitor of the IGBT Chopper/Inverter. Record the generator speed below when you observe for the first time that the Dumping LED turns on intermittently. 21. Repeat steps 19 and 20 until the doubly-fed induction generator reactive power at the stator cannot be adjusted to 0 var anymore because the Peak Voltage (% of DC Bus) parameter is at a maximum (i.e., 100%). a It is possible that the Four-Quadrant Dynamometer/Power Supply reaches its maximum mechanical power output value before the peak voltage limit is attained. If this happens, stop your manipulations and proceed directly to the next step. Generator speed at which the rotor windings begin to supply power: r/min 22. In the Four-Quadrant Dynamometer/Power Supply window, stop the Positive Constant-Torque Prime Mover/Brake. In the Chopper/Inverter Control window, stop the Three-Phase, PWM Inverter. On the Power Supply, turn the three-phase ac power source off. 23. In the Data Table window, save the recorded data, then export it to a spreadsheet application. Sort the data by using the generator speed as the reference parameter, from the lowest value to the highest. 46 Principles of Doubly-Fed Induction Generators (DFIG) A

25 Exercise 3 Doubly-Fed Induction Generators Procedure In the spreadsheet application, invert the polarity of the generator mechanical power. The polarity of the generator mechanical power is now positive. a For the purpose of plotting graphs, it is more convenient to consider the mechanical power parameter as mechanical power supplied by the prime mover to the generator (i.e., as a positive mechanical power value) than as mechanical power used by the generator (i.e., as a negative mechanical power value). In the spreadsheet application, delete the values of generator active power at the rotor that are equal to or lower than about 0 W. Using the remaining values of active power at the rotor, calculate the function relating the generator active power at the rotor to the generator speed. Then, using the function, extrapolate the actual values of active power at the rotor when power is supplied from the generator rotor windings to the three-phase ac power source. a The doubly-fed induction generator setup used in this exercise does not allow power produced by the generator rotor windings to be returned to the threephase ac power source. Because of this, it is necessary to extrapolate the actual values of active power at the rotor when power is returned to the three-phase ac power source using the directly proportional function relating the generator active power at the rotor to the generator speed. In the spreadsheet application, add a new parameter to the results: the total power generated by the doubly-fed induction generator. To calculate the generator total power, subtract the active power at the rotor from the active power at the stator. The generator total power is thus equal to the amount of power supplied to the three-phase ac power source by the generator minus the amount of power that the three-phase ac power source supplies to the generator rotor. This means that, when the active power at the rotor is negative and that power is supplied by the generator rotor windings, the active power at the rotor adds to the active power at the stator when calculating the generator total power. Finally, add another parameter to the results: the doubly-fed induction generator efficiency. To calculate the generator efficiency, divide each total power value by the corresponding mechanical power value, then multiply the result by 100 to express the efficiency as a percentage. 24. Do the results you obtained confirm that a doubly-fed induction machine operates like a variable-speed synchronous generator? Briefly explain why. 25. On the same graph, plot curves of the doubly-fed induction generator mechanical power, active power at the stator, active power at the rotor, and total power as a function of the generator speed using the results you exported to the spreadsheet application. A Principles of Doubly-Fed Induction Generators (DFIG) 47

26 Exercise 3 Doubly-Fed Induction Generators Procedure 26. Consider the three schemas shown in Figure 13 (see next page) representing the doubly-fed induction generator when the generator rotates at minimum speed, singly-fed synchronous speed, and maximum speed. Using the results you exported to the spreadsheet application, draw the power balance of the doubly-fed induction generator by filling in the arrows representing power values in the three schemas of Figure 13. Describe what happens to the doubly-fed induction generator power balance as the generator speed increases and the magnetic flux in the generator is maintained at the optimal value (i.e., when the reactive power at the stator is equal to 0 var). 27. Plot the curve of the doubly-fed induction generator efficiency as a function of the generator synchronous speed using the results you exported to the spreadsheet application. Observe the graph. Describe the relationship between the doubly-fed induction generator efficiency and the generator speed when the magnetic flux in the generator is maintained at the optimal value (i.e., when the reactive power at the stator is equal to 0 var). 28. Considering the results you obtained in this exercise, is it preferable for a doubly-fed induction generator to operate at hyposynchronous speed, synchronous speed, or hypersynchronous speed? Explain. 29. Close LVDAC-EMS, then turn off all the equipment. Disconnect all leads and return them to their storage location. 48 Principles of Doubly-Fed Induction Generators (DFIG) A

27 Exercise 3 Doubly-Fed Induction Generators Procedure W W W Prime mover DFIG At minimum rotor speed ( ) W W W W Prime mover DFIG At singly-fed synchronous speed ( ) W W W W Prime mover DFIG At maximum rotor speed ( ) W Figure 13. Power balance of the doubly-fed induction generator when the generator rotates at minimum speed, singly-fed synchronous speed, and maximum speed. A Principles of Doubly-Fed Induction Generators (DFIG) 49

28 Exercise 3 Doubly-Fed Induction Generators Conclusion CONCLUSION In this exercise, you learned how three-phase wound-rotor induction machines can operate as doubly-fed induction generators. You saw that doubly-fed induction generators operate like variable-speed synchronous generators. You also saw how doubly-fed induction generators are used in wind turbines to generate large amounts of electrical power. You learned the advantages of using doubly-fed induction generators in wind turbines. REVIEW QUESTIONS 1. How is it possible to vary the rotor speed of a doubly-fed induction generator while the amplitude and frequency of the ac power network to which the generator is connected remains constant? 2. Consider a doubly-fed induction generator whose rotor rotates in the counterclockwise direction. If the ac currents fed into the generator rotor windings create a magnetic field rotating in the clockwise direction, will the amplitude and frequency of the voltages produced by the generator be lower than, equal to, or higher than during singly-fed operation (at the same rotor speed)? 3. Consider a doubly-fed induction generator having 8 magnetic poles. The generator supplies power to a 50 Hz ac power network. Knowing that a prime mover makes the generator rotate at a speed of 900 r/min, calculate the frequency of the ac currents that need to be fed into the generator rotor windings so that the generator is synchronized with the ac power network. Also, determine the direction of rotation of the rotating magnetic field created by the ac currents fed into the generator rotor windings. 4. Consider a doubly-fed induction generator having four magnetic poles. The generator supplies power to a 60 Hz ac power network. Knowing that a prime mover makes the generator rotate at a speed of 1530 r/min, calculate the frequency of the ac currents that need to be fed into the generator rotor windings so that the generator is synchronized with the ac power network. 50 Principles of Doubly-Fed Induction Generators (DFIG) A

29 Exercise 3 Doubly-Fed Induction Generators Review Questions Determine also the direction of rotation of the rotating magnetic field created by the ac currents fed into the generator rotor windings. 5. What are the main advantages of using doubly-fed induction generators instead of asynchronous generators in wind turbines? A Principles of Doubly-Fed Induction Generators (DFIG) 51

30

31 Sample Extracted from Instructor Guide

32

33 Exercise 3 Doubly-Fed Induction Generators Exercise 3 Doubly-Fed Induction Generators ANSWERS TO PROCEDURE STEP QUESTIONS 11. Yes Yes Yes 21. Generator speed at which the rotor windings begin to supply power: 2160 r/min A Principles of Doubly-Fed Induction Generators (DFIG) 7

34 Exercise 3 Doubly-Fed Induction Generators 23. The results obtained are presented below. Doubly-fed induction generator speed, mechanical power, active power at the stator, reactive power at the stator, active power at the rotor, rotor frequency, total power, and efficiency. Speed (r/min) Mechanical power (W) Stator active power (W) Stator reactive power (var) Rotor active power (W) Rotor frequency (Hz) Total power (W) Efficiency (%) * * * * * * * Indicates results that were obtained through extrapolation. 8 Principles of Doubly-Fed Induction Generators (DFIG) A

35 Exercise 3 Doubly-Fed Induction Generators 24. Yes because the doubly-fed induction generator rotates at the synchronous speed and the synchronous speed of the generator can be modified by adjusting the value of the rotor frequency. 25. The resulting graph is shown below Mechanical power Stator active power Generator power (W) Total power 50.0 Rotor active power Generator speed Doubly-fed induction generator mechanical power, active power at the stator, active power at the rotor, and total power as a function of the generator speed. 26. The power balance of the doubly-fed induction generator when the generator rotates at minimum speed, singly-fed synchronous speed, and maximum speed are presented on the following page. A Principles of Doubly-Fed Induction Generators (DFIG) 9

36 Exercise 3 Doubly-Fed Induction Generators W W W Prime mover DFIG At minimum rotor speed ( ) W W W W Prime mover DFIG At singly-fed synchronous speed ( ) 50.6 W W W W Prime mover DFIG At maximum rotor speed ( ) 27.4 W Power balance of the doubly-fed induction generator when the generator rotates at minimum speed, singly-fed synchronous speed, and maximum speed. 10 Principles of Doubly-Fed Induction Generators (DFIG) A

37 Exercise 3 Doubly-Fed Induction Generators As the doubly-fed induction generator speed increases and the magnetic flux in the generator is maintained at the optimal value, the active power at the stator remains constant, while the active power at the rotor decreases. Consequently, the generator total power increases. Furthermore, when the generator speed reaches a certain value (in hypersynchronous operation), the rotor begins supplying active power (the polarity of active power at the rotor becomes negative), which adds up to the active power supplied by the stator. 27. The resulting graph is shown below Generator efficiency (%) Generator speed (r/min) Doubly-fed induction generator efficiency as a function of the generator synchronous speed. The doubly-fed induction generator efficiency increases slightly with the generator speed. a The relatively low efficiency of the doubly-fed induction generator is primarily due to its small size. In large doubly-fed induction generators such as the ones used in wind turbines, the generator efficiency is much higher. 28. It is preferable for a doubly-fed induction generator to operate at hypersynchronous speed as the generator efficiency increases with the generator speed of rotation. A Principles of Doubly-Fed Induction Generators (DFIG) 11

38 Exercise 3 Doubly-Fed Induction Generators ANSWERS TO REVIEW QUESTIONS 1. The rotor speed of a doubly-fed induction generator can be varied by adjusting the frequency of the ac currents fed into the generator rotor, even though the amplitude and frequency of the ac power network to which the generator is connected remains constant. 2. If the rotor of a doubly-fed induction generator rotates in the opposite direction to the magnetic field created in the rotor, the amplitude and frequency of the voltages produced by the generator will be lower than during normal singly-fed operation (at the same rotor speed). 3. The frequency of the ac currents that need to be fed into the doubly-fed induction generator rotor windings so that the generator is synchronized with the ac power network is calculated below. = r/min 8 poles = 50 Hz = 10 Hz 120 As the polarity of the rotor frequency is negative, the rotating magnetic field created by the ac currents fed into the generator rotor windings must rotate in the opposite direction to the generator rotor. 4. The frequency of the ac currents that need to be fed into the doubly-fed induction generator rotor windings so that the generator is synchronized with the ac power network is calculated below. = r/min 4 poles = 60 Hz =9 Hz 120 As the polarity of the rotor frequency is positive, the rotating magnetic field created by the ac currents fed into the generator rotor windings must rotate in the same direction as the generator rotor. 5. Using doubly-fed induction generators in wind turbines instead of asynchronous generators offers the following advantages: 1) Operation at variable rotor speed while the amplitude and frequency of the generated voltages remain constant, 2) Optimization of the amount of power generated as a function of the wind available up to the nominal output power of the wind turbine generator, 3) Virtual elimination of sudden variations in the rotor torque and generator output power, 4) Generation of electrical power at lower wind speeds, and 5) Control of the power factor (e.g., in order to maintain the power factor at unity). 12 Principles of Doubly-Fed Induction Generators (DFIG) A