# ATD WATT INVERTER

Save this PDF as:

Size: px
Start display at page:

## Transcription

2 Multiply: AMPS X 110 (AC voltage) = WATTS This formula yields a close approximation of the continuous load of your appliance Multiply: WATTS X 2 = Starting Load This formula yields a close approximation of the starting load of your appliance. Most often the start up load of the appliance or power tool determines whether your inverter has the capability to power it. To determine whether the inverter will operate a particular piece of equipment or appliance, run a test. The inverters are designed to automatically shut down in the event of a power overload. This protection feature prevents damage to the unit while testing appliances and equipment with ratings in the 2000 watt range. If an appliance in the 2000 watt range will not operate properly when first connected to the inverter, turn the inverter rocker switch ON(I), OFF(0), and ON(I) again in quick succession. If this procedure is not successful, it is likely that the inverter does not have the required capacity to operate the appliance in question. Important The inverter is designed to operate from a 12-volt power source only. Do not attempt to connect the inverter to any other power source, including any AC power source. Do not attempt to extend or otherwise modify the 12-volt power cord attached to your inverter. 110 volts of current can be lethal. Improper use of your inverter may result in property damage, personal injury or loss of life. 2

4 1. When calculating the amp/hour of the battery, find its reserve minutes" rating. This is typically is marked on the battery label along with the "Cold Cranking Amps" (CCA) rating. If you multiply the reserve minutes rating of the battery by 0.3 it will tell you the battery amp/hour. 2. To estimate the maximum battery power the inverter will require to run a piece of equipment or appliance, divide its continuous load wattage equipment by Conclusion: The reserve power of a battery with a 150 reserve minutes rating is sufficient to satisfy the continuous load demand placed on the inverter for a maximum of about one hour. (45 amps/hour-amp draw = 1 hour). Note: The type of battery you use to power your inverter is important. Batteries designed to start engines have multiple layers of very thin plates. These provide extensive surface area that will produce a powerful short burst of electrical power required to start combustion engines. Using an inverter will cause a battery to discharge and recharge often. We recommend that you use a different type of battery that is designed specifically for this type of load requirement. Deep cycle (marine) batteries generally have the highest reserve ratings. They are designed with thicker plates making them capable of withstanding repeated complete drains of power and recharging. If you do not have a deep cycle battery we recommend that you run the engine of your vehicle when operating the inverter. Connection Cable Gauges. When connecting the inverter to the power source use the thickest wire available, in the shortest length practical. If the inverter and the battery are positioned within four feet of each other, a minimum of # 4 gauge wire should be used to make the connections. When the distance between them is four to six feel, a minimum of #2 gauge wire is required. When separated by more than six feet, always use # 0 gauge wire. See last page of this manual for wire size recommendations. Connecting Your inverter. 1. Make sure the ON/OFF switch located on the front panel of the inverter is in the OFF(0) position. 2. Connect the cables to the power input terminals at the rear of the inverter. Make sure to match the negative (Black) terminal on the 12 volt power source. Then repeat this procedure with the positive (Red) terminal connecting a wire to the positive terminal of the 12V volt power source. Make sure you have a good secure connection, but do not over tighten these screws. Note: Loose connections can result in a severe decrease in voltage which may cause damage to the wires and insulation. Failure to make a proper connection between the inverter and the power source will result in reverse polarity. Reverse polarity will blow the internal fuses in the inverter and may cause permanent damage to the inverter. Damage caused by reverse polarity is not covered under the warranty. Making the connection between the Positive terminals may cause a spark as a result of current flowing to charge capacitors within the inverter. This is a normal occurrence. Due 4

5 to the possibility of sparking, however, it is extremely important that both the inverter and the 12 volt battery be positioned far from any possible source of flammable fumes or gases. Failure to heed this warning could result in fire or explosion. 3. Locate the Ground Lug Terminal at the rear of the inverter. Run a wire from this terminal to a proper grounding point using the shortest practical length wire as recommended on the last page of this manual. You can connect this wire to the chassis of your vehicle or to the grounding system in your boat. As an alternative when in remote locations the ground wire can be connected to the earth (one way to accomplish this is to attach it to a metal rod driven into the ground). Before connecting the ground, make certain that the inverter is turned off. Operating the inverter without correctly grounding the unit may result in electrical shock. 4. Turn On (I) the inverter. Make certain that the Over Load LED Indicators are not lit. 5. Turn OFF (0) the inverter. The Over Load and LEDS may briefly "blink". This is normal. The internal audible alarm may also sound a short "chirp" This is also normal. 6. When you have confirmed that the appliance to be operated is turned off, plug the appliance into one of the two 110V AC Outlets on the front panel of the inverter. 7. Turn the inverter on. 8. Turn the appliance on. Note: The audible alarm may make a momentary "chirp" when the inverter is turned OFF(0). This same alarm may also sound when the inverter is being connected to or disconnected from the 12 volt power source. When using an extension cord from the inverter to the appliance the extension cord should be no more than 50 feet long. At this length there should be no measurable decrease in power from the inverter. Television and Audio Suggestions Although these inverters are shielded and filtered to minimize signal interference, some interference with your television picture may be unavoidable, especially with weak signals. However, here are some suggestions that may improve reception. 1. First, make sure that television antenna produces a clear signal under normal operating conditions. Also, ensure that the antenna cable is properly shielded and of good quality. 2. Change the positions of the inverter, antenna cables and television power cord. 3. Isolate the television, its power cord and antenna cables from the 12 volt power source by running an extension cord from the inverter to the television set. 4. Coil the television power cord and the input cables running from the 12 volt power source to the inverter. 5. Attach a "Ferrite Data Line Filter" to the television power cord. More than one filter may be required. These filters are available at most electronic supply stores. Note: Inexpensive sound systems may emit a "buzzing" sound when operated with the inverter. This is due to inadequate filters in the sound system. There is no solution to this problem short of purchasing a sound system with a higher quality power supply. 5

6 Operating a Microwave oven with Your Power Inverter The power rating used with microwave ovens is the "cooking power" which qualifies as the power being "delivered" to the food being micro waved. The actual operating power requirement rating is higher than the cooking power rating. This is usually referenced on the back of the microwave. If the operating power requirement cannot be found on the back of the microwave, check the owner's manual or contact the manufacturer. Safety Precautions. For best results place the power inverter on a reasonably flat surface. Keep the inverter dry. Do not expose it to rain or moisture. DO NOT operate the inverter if the inverter, device being operated or any other surfaces that may come in contact with any power source are wet. Water and many other liquids can conduct electricity which may lead to serious injury or death. Avoid placing the inverter on or near heating vents, radiators or other sources of heat. Do not leave the inverter in the passenger compartment of your vehicle. Store in a cool dry place. Do not place the inverter in direct sunlight. Ideal air temperature should be between 50 F and 80 F. In order to properly disperse heat generated while the inverter is in operation, keep it well ventilated. While in use, maintain several inches of clearance around the top and sides of the inverter. Do not use the inverter near flammable materials. Do not place the inverter in areas such as battery compartments where fumes or gases may accumulate. When the inverter will be operating appliances with high continuous load ratings for extended periods, it is not advisable to power the inverter with the same batter used to power your car or truck. If the car or truck battery is utilized for an extended period, it is possible that the battery voltage may be drained to the point where the battery has insufficient reserve power to start the vehicle. It may be advisable to operate the inverter from a bank of batteries of the same type in a "parallel" configuration. Two such batteries will generate twice the amp\hours of a single battery; three batteries will generate three times the amp hours and so on. How Power Inverters Work. There are two stages in which a power inverter changes the 12 volt DC (or battery) power into 110V AC (household current). STAGE 1: The inverter uses a DC-to-DC converter to increase the DC input voltage from the power source to 145 volts DC. STAGE 2: The inverter then converts the high voltage DC into 110V AC (household current), using advanced MOSFET (Metal-Oxide-Semiconductor Field Effect Transistor) transistors in a full bridge configuration. This design provides all our inverters with the capability to start and run 6

7 difficult reactive loads, while providing excellent overload capability The waveform that is generated by this conversion is a "modified sine wave" as shown in the diagram below. The modified sine wave produced by our inverters has a root mean square (RMS) voltage of 110 volts. The majority of AC voltmeters are calibrated for RMS voltage and assume that the measured waveform will be a pure sine wave. Consequently, these meters will not read the RMS modified sine wave voltage correctly and, when measuring the inverter output, the meters will read about 20 to 30 volts too low. To accurately measure of the output voltage of the inverter, use a true RMS reading voltmeter such as a Fluke 87 Fluke 8060A Beckman 4410, Triplet 4200 or any multimeter identified as "True RMS" In Review. Never attempt to operate the inverter from any power source other than a 12 volt DC volt battery. Always disconnect the inverter when not in use. Always make certain the power cable terminal connections run Negative (-) to Negative (-) and Positive (+) to Positive (+). Check these connections frequently to make sure they are remain secure. Use the heaviest gauge wire available to connect the inverter to the power source. While connecting the inverter to the power source, make certain that the inverter is positioned far away from any potential source of flammable fumes or gases, Always ground the inverter before operating it. Make certain the power consumption of the appliance or equipment you wish to operate is compatible with the capacity of the inverter. Do not exceed 2000 watts. When attempting to operate battery chargers, monitor the temperature of the battery charger for approximately 10 minutes. If the battery charger becomes abnormally warm, disconnect it from the inverter immediately. When operating the inverter with an automobile or marine battery, start the engine every 30 to 60 minutes and let it run for approximately 20 minutes to recharge the battery. In the event of a continuous audible alarm or automatic shut down, turn the inverter OFF immediately. Do not restart the inverter until the source of the problem has been identified and corrected. To avoid battery drain, always disconnect the inverter when not in use. Do not expose the inverter to rain or moisture. Avoid placing the inverter near sources of heat or in direct sunlight. While in use, make sure the inverter is properly ventilated. Do not operate the inverter near flammable materials, fumes or gases. 7

8 Troubleshooting PROBLEM: Low or No Output Voltage Reason: Poor contact with lighter socket or battery clamps Solution: Unplug and reinsert 12 volt plug or reattach battery clamps. Reason: Using incorrect type of voltmeter to test output voltage. Solution: Use true RMS reading meter. PROBLEM: Red LED Indicator On Reason: Battery voltage below 9.5 volts. Solution: Recharge or replace battery. Reason: Equipment being operated draws too much power. Solution: Use a higher capacity inverter or do not use this equipment. Reason: Inverter is too hot (thermal shut down mode). Solution: Allow inverter to cool. Check for adequate ventilation. Reduce the load on the inverter to rated continuous power output. Reason: Unit may be defective. Solution: See Warranty and call customer service. PROBLEM: TV Interference Reason: Electrical interference from the inverter. Solution: Add a ferrite data line filter on to the TV power cord. Refer to TV & Audio section of this manual. PROBLEM: Low Battery Alarm On All The Time Reason: Input voltage below 10.5 volts. Solution: Keep input voltage above 10.5 volts to maintain regulation. Reason: Poor or weak battery. Solution: Recharge or Replace battery. Reason: Inadequate power being delivered to the inverter or excessive voltage drop Solution: Check condition of cigarette lighter socket. Clean or replace ifnecessary. Or check cable clamp connections. 8

9 PROBLEM: TV Does Not Work Reason: TV does not turn on. Solution: Try turning the inverter ON/OFF/ON. Contact TV manufacturer for start up surge specifications and/or to see if the TV is compatible with a modified sine wave. A larger inverter may be required. SPECIFICATIONS: Max. Continuous Power Watts Surge Capability (Peak Power) Watts No Load Current Draw... <1.2A Waveform...Modified Sine Wave Input Voltage Range... DC10-15V AC Receptacles V AC 3 prong grounded Fuse... 8 x 30 amp (spade type) Dimensions Wx230Lx76.5Hmm (14.84 x 9.06 x 3.01 ) Weight Ib INVERTER CABLES 200W & 400W COME WITH A CIGARETTE LIGHTER PLUG/CABLE & CLAMP ON BATTERY CABLES 800W OR GREATER MUST BE HARD WIRED TO BATTERY *USE THE THICKEST WIRE AVAILABLE IN THE SHORTEST LENGTH PRACTICAL Wattage 0'-4' Length 5'-10' Length 800W #2 AWG #0 AWG 1000W #0 AWG #2/0 AWG 1500W #0 AWG #2/0 AWG 2000W #2/0 AWG #4/0 AWG 3000W #2/0 AWG #4/0 AWG 6000W #2/0 AWG #4/0 AWG 9

### ATD WATT INVERTER

ATD-5954 1500 WATT INVERTER Welcome. This ATD product has been carefully engineered and manufactured to give you dependable operation. Please read this manual thoroughly before operating your new ATD product,

### XP800i POWER INVERTER OWNER S MANUAL

XP800i POWER INVERTER OWNER S MANUAL INTRODUCTION Dear Whistler Customer, For many of us, a vehicle is more than just transportation. It can be a mobile office, communications or entertainment center,

### XP1200i/XP1600i/XP2000i/XP3000i POWER INVERTER OWNER S MANUAL. XP1200i. XP1600i. XP2000i. XP3000i

XP1200i/XP1600i/XP2000i/XP3000i POWER INVERTER OWNER S MANUAL XP1200i XP1600i XP2000i XP3000i INTRODUCTION Dear Whistler Customer, For many of us, a vehicle is more than just transportation. It can be

### ATD WATT INVERTER

ATD 5954 1500 WATT INVERTER For use with 12V systems Input DC voltage range: DC 10V 15V Overload and short circuit protection Built in cooling fan (2) 110V AC 3 prong grounded receptacles and overload

### O W N E R ' S M A N U A L

1500 Watt DC to AC Power Inverter C o n v e r t s 1 2 V D C B a t t e r y P o w e r t o 1 1 0 V A C H o m e P o w e r O W N E R ' S M A N U A L SAVE THESE INSTRUCTIONS The recommended source of power is

### PI1500X Power Inverter User s Manual

PI1500X Power Inverter User s Manual featuring WARNING Failure to follow instructions may cause damage or explosion, always shield eyes. Read entire instruction manual before use. Warning: This product

### OWNER S MANUAL. Please read installation and operation instruction before using this Power inverter.

OWNER S MANUAL DP AUDIO Model No. DN350 12 Volt DC to 115 Volt AC 150 WATT 300WATT HIGH SURGE POWER INVERTER Please read installation and operation instruction before using this Power inverter. Contents

### Inverter User Manual

Inverter User Manual -------------for standard model DC TO AC Power Inverter CONTENTS Safety First 1. Introduction 2. Installation Guidelines 3. Using the inverter 4. Troubleshooting 5. Specifications

### Go Power! Manual. GP-1750HD Inverter GP-2500 Inverter

Go Power! Manual GP-1750HD Inverter GP-2500 Inverter Go Power! Electric Inc. PO Box 6033 Victoria, BC V8P 5L4 Tel: 866-247-6527 Fax: 866-607-6527 Email: info@gpelectric.com Table of Contents 1. INTRODUCTION...

### 5000 Watt AC Inverter

R Item no. 2012 5000 Watt AC Inverter User s Manual Thank you for purchasing this 5000 Watt DC to AC Power Inverter by Wagan Tech. With minimal care and proper treatment it will provide years of reliable

### 1000 Watt Power Inverter INSTRUCTION MANUAL HT87112-AUOXY

1000 Watt Power Inverter INSTRUCTION MANUAL HT87112-AUOXY CONTENTS Warranty 2 Introduction 3 Environmental protection 3 Specifications 3 General safety warnings and instructions 4 Important safety instructions

### GP-1000 Inverter. Go Power! Electric Inc. PO Box 6033 Victoria, BC V8P 5L4 Tel: Fax:

Go Power! Manual GP-1000 Inverter Go Power! Electric Inc. PO Box 6033 Victoria, BC V8P 5L4 Tel: 866-247-6527 Fax: 866-607-6527 Email: info@gpelectric.com Table of Contents 1. INTRODUCTION 3 2. SPECIFICATIONS

### 3000W POWER INVERTER. User Manual

3000W POWER INVERTER User Manual Posts AC outlets Digital display ON/OFF button Remote control connection port (remote control switch is not included) USB port Two set of heavy duty input cable P a g e

### Model: PIF-2000 Power Inverter Converts 12V DC Battery Power to AC Household Power

OWNERS MANUAL Model: PIF-2000 Power Inverter Converts 12V DC Battery Power to AC Household Power PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE. This manual will explain how to use the converter

### item #2204 User s Manual SHEMO TXC

item #2204 User s Manual SHEMO080100244TXC Introduction Thank you for purchasing this Wagan Pure Sine Wave DC to AC Power Inverter. It delivers a true sine wave AC identical to that of commercial power.

### Owner s Manual. PowerVerterDC-to-AC Inverter

Owner s Manual PowerVerterDC-to-AC Inverter Model: PV700HF Input V DC Output 0V, 60Hz AC Reliable AC Power Wherever You Need It Congratulations! You've purchased a high-quality Inverter designed to function

### DC-AC MODIFIED SINE-WAVE INVERTER OWNER S MANUAL SI-750HP MODEL: Please read this manual before operating your inverter.

AC C POWER SOURCE CE DC-AC MODIFIED SINE-WAVE INVERTER 110-17 Fawcett Road, Coquitlam B.C., Canada V3K 6V2 e-mail: samlex@samlexamerica.com website: www.samlexamerica.com 1-800-561-5885 MODEL: SI-750HP

### Battery Power Inverters

Battery Power Inverters Renogy 500W 1000W 2000W Pure Sine Wave Inverter Manual 2775 E. Philadelphia St., Ontario, CA 91761 1-800-330-8678 1 Version 1.4 Important Safety Instructions Please save these instructions.

### GSL Electronics Modified Sine Wave Power Inverters

GSL Electronics Modified Sine Wave Power Inverters Congratulations on choosing one of our Modified Sine Wave Inverters for your application. There are 6 models in the range, which will meet most of your

### Pure Sine Wave Inverter GP-HS1500. Owner s Manual

Pure Sine Wave Inverter GP-HS1500 Owner s Manual 2 Table of Contents Introduction 3 Specifications 4 Name and Main Function 5 Installation 7 Operation 9 Operating Limits 13 Troubleshooting 13 Maintenance

### DC TO AC POWER INVERTER

DC TO AC POWER INVERTER 12V / 24V / 48Vdc Input 115V / 230Vac Output 150W ~ 6000W Output cont. L-Series User Manual Before install and use your Inverter, read the User Manual and safety instructions. Cooler

### Pure Sine Wave Power Inverter SSW A SSW A SSW A SSW A SSW A

Pure Sine Wave Power Inverter SSW-350-12A SSW-600-12A SSW-1000-12A SSW-1500-12A SSW-2000-12A Owner's Manual Please read this manual before installing your inverter 1 IMPORTANT SAFETY INSTRUCTIONS THIS

### 230 VOLT INVERTERS. Operation Manual

230 VOLT INVERTERS Model: TL INV2500 12V 2500W Model: TLINV2500/24 24V 2500W Operation Manual MODEL Nos: TLINV2500 TLINV2500/24 Output power continuous 2500W 2500W Output power surge 5000W 5000W Overload

### About Xantrex Xantrex Technology Inc is a world-leading supplier of advanced power electronics with a product line that ranges from 50 Watt mobile uni

About Xantrex Xantrex Technology Inc is a world-leading supplier of advanced power electronics with a product line that ranges from 50 Watt mobile units to 1 MW utility-scale or standalone systems for

USER MANUAL Copyright 2006, PowerStation, LLC All rights reserved MODEL: PS5000M CONTENTS Warning Information 1 3 Introduction 4 Features 4 Getting to know your PS5000M 5-6 Operation 7 Charging before

### Pure Sine Wave Inverter Charger

Pure Sine Wave Inverter Charger Renogy 1000W 2000W Pure Sine Wave Inverter Charger Manual 2775 E. Philadelphia St., Ontario, CA 91761 1-800-330-8678 Version 1.6 1 Important Safety Instructions Please save

### AUTOMOTIVE. Inverters and Battery to Battery Chargers Information and Install Guide V1. Specifications Subject To Change Without Notice

AUTOMOTIVE Inverters and Battery to Battery Chargers Information and Install Guide V1 Specifications Subject To Change Without Notice Contents What does a power inverter do, and what can I use one for?

### AUTOMOTIVE POWER INVERTERS INSTRUCTIONS. Item #31463, #31464, #31465

AUTOMOTIVE POWER INVERTERS INSTRUCTIONS Item #31463, #31464, #31465 EASTWOOD AUTOMOTIVE POWER INVERTERS are heavy-duty professional grade pieces of equipment designed to bring 120 volt power to any automobile.

### Pro Series 6 in 1 powerstation / jumpstart

Pro Series 6 in 1 powerstation / jumpstart Model No. JSM-0599 OWNER'S MANUAL Customer Service Tel: 1-800-268-3319 Superex Canada Limited, Toronto M2H 3B8 Made in China IMPORTANT SAFETY INSTRUCTIONS 1.

### HG PI2000. How Your HG PI2000 Power Inverter Works Watt Power Inverter. Nothing comes close to a Cobra TM

Operating Instructions for Your HighGear by Cobra 2000 Watt Power Inverter HG PI2000 How Your HG PI2000 Power Inverter Works How Your Cobra Power Inverter Works The Cobra Power Inverter is an electronic

### 1000-Watt Energy Center

1000-Watt Energy Center OPERATING INSTRUCTIONS Patent Pending Sierra Wave 1000-Watt Energy Center #9675 The Sierra Wave 1000-Watt Energy Center is a heavy duty and efficient portable power center offering

### POWERSOURCEPURE INSTRUCTIONS. Pure Sine Wave Inverter. RINV1200P REINV1200P RINV2200P REINV2200P

POWERSOURCEPURE Pure Sine Wave Inverter RINV1200P REINV1200P RINV2200P REINV2200P INSTRUCTIONS Retain these instructions for future reference www.ringautomotive.co.uk OVERVIEW The Ring Pure Sine Wave (PSW)

### 1RECHARGEABLE APPLIANCES

1RECHARGEABLE APPLIANCES 1 CAUTION Certain rechargers for small nickel cadmium batteries can be damaged if connected to the unit. Two types of equipment are particularly prone to this problem: 1. Small

### AIMS POWER INVERTER 2500 WATT / 5000 WATT PEAK

AIMS POWER INVERTER 2500 WATT / 5000 WATT PEAK PWRINV 2500W ASSEMBLY AND OPERATING INSTRUCTIONS TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE. ITEM Continuous

### XPower Powerpack 600HD. Owner s Guide

by XPower Powerpack 600HD Owner s Guide About Xantrex Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with products from 50 watt mobile units to one MW utility-scale

### 800 WATT POWER INVERTER

Introduction Our Thanks to You The Cobra line of quality products includes: Operating Instructions Thank you for purchasing the Cobra CPI 850 inverter. Properly used, this Cobra product will give you many

### Item no Smart AC 200 USB. User s Manual

R Item no. 2402 Smart AC 200 USB User s Manual Smart AC 200 Watt with USB by Wagan Tech User s Manual Read before using this equipment Thank you for purchasing Smart AC 200 Watt with USB by Wagan Tech.

### 1200+ WITH TIMER V1.00 OWNERS MANUAL

1200+ WITH TIMER V1.00 1 1200+ WITH TIMER V1.00 OWNERS MANUAL CONTENTS General Information... 2 Operating Environment... 5 Features... 6 Installation Instructions... 7 Inverter Ground and Remote Sense

### ATD-5921 RECHARGEABLE 12 VOLT 18 AMP/HOUR JUMP START OWNERS MANUAL

ATD-5921 RECHARGEABLE 12 VOLT 18 AMP/HOUR JUMP START OWNERS MANUAL 900 PEAK AMPS/400 CRANKING AMPS OF STARTING POWER. STARTS CARS, TRUCKS, RV s AND BOATS WITHOUT THE NEED OF ANOTHER VEHICLE OR AC POWER

### WARNING: CAUTION: Notice : XR175 Owner's Guide

WARNING: This Unit employs Components that tend to produce arcs or sparks To prevent fire or explosion, do not install in compartments containing batteries or flammable materials - SHOCK HAZARD. DO NOT

### Models: SP3, SPSS3 Automatic Battery Charger

OWNERS MANUAL Models: SP3, SPSS3 Automatic Battery Charger PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE. This manual will explain how to use the charger safely and effectively. Please read and

### Owner s Manual & Safety Instructions

Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s

### Modified Sine Wave Inverter USER MANUAL

Modified Sine Wave Inverter USER MANUAL DC-AC Power Inverter Special Feature: Fuse: Built-out USB:5V,500mA Modified sine wave output High reliability and high efficiency High load ability Temperature and

### Operating Instructions for Your Cobra 150 Watt POWER INVERTER M ODEL CPI 150 FAULT OFF. Nothing comes close to a Cobra

Operating Instructions for Your Cobra 150 Watt INVERTER M ODEL CPI 150 Nothing comes close to a Cobra 00 Congratulations Thank you for purchasing the CPI 150 Power Inverter from Cobra. When used properly,

### ATD-5925 RECHARGEABLE 12 VOLT 18 AMP/HOUR JUMP START WITH BUILT-IN 260 PSI AIR COMPRESSOR OWNERS MANUAL

ATD-5925 RECHARGEABLE 12 VOLT 18 AMP/HOUR JUMP START WITH BUILT-IN 260 PSI AIR COMPRESSOR OWNERS MANUAL 1000 PEAK AMPS/400 CRANKING AMPS OF STARTING POWER. STARTS CARS, TRUCKS, RV s AND BOATS WITHOUT THE

### XPower Inverter 1000 Plus and 1750 Plus. Owner s Guide

XPower Inverter 1000 Plus and 1750 Plus Owner s Guide About Xantrex Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with products from 50 watt mobile units

### Owner's Manual. DC-AC Power Inverter. Models: (750W) (400W) (200W) or GENERAC

Owner's Manual DC-AC Power Inverter Models: 006180-0 (750W) 006179-0 (400W) 006178-0 (200W) 200W Model 400W/750W Models Power inverter produces powerful voltage that can cause death or great physical harm.

### Pure Sine Wave Inverter User Manual

48-3000RM 2U 19, 2 Post Rack Mount & 4 Post Open Frame Cabinet Mount Pure Sine Wave Inverter User Manual Newmar PO Box 1306 Newport Beach, CA 92663 www.poweringthenetwork.com Tel: 714-751-0488 M-483000RM

### CONVERTS 12 VOLT DC 230/240 VOLT AC POWER INVERTER POWERS HOUSEHOLD APPLIANCES FROM A 12 VOLT BATTERY

CONVERTS 12 VOLT DC 230/240 VOLT AC POWER INVERTER POWERS HOUSEHOLD APPLIANCES FROM A 12 VOLT BATTERY P/No.s IM150, IM300, IM600, IM1000, IM2000 WARNING For use with negatively earthed vehicles & systems

### OPERATOR S MANUAL. Portable Power Model No

OPERATOR S MANUAL Portable Power 1150 Model No. 28.71988 Read and follow all Safety Rules and Operating Instructions before Every Use of this Product. Save these instructions. Sears Brands Management Corporation,

INSTANT JUMPSTARTING POWER USER MANUAL Copyright PowerStation, LLC All rights reserved MODEL: PS1100 CONTENTS Warning Info 1 2 Introduction 3 Features 3 Getting to know your PS1100 4 5 Operation 6 Charging

### OPERATING INSTRUCTIONS. Note: 6V Charging. Requires Manual Shut Off.

Requires Manual Shut Off. 6 / 2 AMP,, DUAL RATE BATTER TTERY CHARGER 45005 OPERATING INSTRUCTIONS E224783 E224783 Note: 6V Charging Due to continuing improvements, actual product may differ slightly from

### 2500 WATT POWER INVERTER

Introduction Our Thanks to You The Cobra line of quality products includes: Operating Instructions Thank you for purchasing the Cobra Power Inverter CPI2590. Properly used, this Cobra product will give

### This file was converted to PDF format. If you are interested in a Microsoft PowerPoint formatted file send a request to:

This file was converted to PDF format. If you are interested in a Microsoft PowerPoint formatted file send a request to: pm_eps@nmci.usmc.mil TABLE OF CONTENTS Published by the Program Manager, Expeditionary

### S150,S300 Series Pure Sine Wave Inverter User s Manual

S150,S300 Series Pure Sine Wave Inverter User s Manual List of contents 1. Important Safety Instructions 3 1-1 General Safety Precautions 3 1-2 Precautions When Working With Batteries.. 3 2. Features...

### windynation VertaMax

VertaMax Power Inverter PIN-1500-12M PIN-3000-12M User s Manual Table of Contents 1 Introduction... 3 1.1 Features...3 1.2 Safety Information...3 1.3 Specifications...4 1.3.1 Electrical Specifications...

### AC POWER SOURCE PURE SINE WAVE DC-AC INVERTERS OWNER S MANUAL

AC POWER SOURCE PURE SINE WAVE DC-AC INVERTERS MODEL: PST-15S-12A OWNER S MANUAL Please read this manual before operating your inverter. INDEX Contents General Safety & Installation... 3 Warning... 4 Description

### Nature Power Inverters. True Sinewave Inverter Modified Sinewave Inverter. Owner s Manual

Version 1.1 Version 2 Nature Power Inverters True Sinewave Inverter Modified Sinewave Inverter Owner s Manual!!!!!!!!!!! 38304 38204 For safe and optimum performance, the Power Inverter must be used properly.

### XPower Inverter 150. Owner s Guide

by XPower Inverter 150 Owner s Guide About Xantrex Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with products from 50 watt mobile units to one MW utility-scale

### o p e r at i o n & i n s ta l l at i o n m a n u a l SOLAR ENERGY AUSTRALIA Pty Ltd ACN

PICCOLO HIGH performance SINEWAVE INVERTER Models: SEAP-12-150 SEAP-24-250 o p e r at i o n & i n s ta l l at i o n m a n u a l Serial No: Model No: SOLAR ENERGY AUSTRALIA Pty Ltd ACN 081 639 938 SYDNEY.

### VLT SERIES. True Sine Wave AC Power Inverter. Owner s Manual. Owner s Manual D Rev.B

Owner s Manual VLT SERIES True Sine Wave AC Power Inverter 60Hz Models VLT12-600 VLT12-1000 VLT12-1500 VLT24-600 VLT24-1000 VLT24-1500 VLT48-1000 VLT48-1500 50Hz Models VLTE12-600 VLTE12-1000 VLTE12-1500

### S600,S600R Series Pure Sine Wave Inverter User s Manual

S600,S600R Series Pure Sine Wave Inverter User s Manual Table of contents 1. Important Safety Information. 1 1-1 General Safety Precautions 1 1-2 Batteries Precautions.. 1 2. Features... 2 2-1 Applications..

### AUTO CHARGE D PUMP PLUS

INSTRUCTION MANUAL AUTO CHARGE D PUMP PLUS AUTOMATIC DUAL OUTPUT BATTERY CHARGER Designed Specifically for Vehicles with DDEC ENGINES MODEL #: 091-9-DPP INPUT: 120 Volt, 60 Hz, 8 Amps OUTPUT VEHICLE BATTERY:

### 2500 WATT POWER INVERTER

Introduction Our Thanks to You The Cobra line of quality products includes: Operating Instructions Thank you for purchasing the Cobra CPI 2575 inverter. Properly used, this Cobra product will give you

### AUTO CHARGE D2 MODEL #: AUTOMATIC TRIPLE OUTPUT BATTERY CHARGER INSTRUCTION MANUAL

INSTRUCTION MANUAL AUTO CHARGE D2 AUTOMATIC TRIPLE OUTPUT BATTERY CHARGER Designed Specifically for Vehicles with DDEC ENGINES MODEL #: 091-74-12 INPUT: 120 Volt, 60 Hz, 8 Amps OUTPUT VEHICLE BATTERY 1

### Villager III. User Instructions. GTIS Power Systems

Villager III User Instructions GTIS Power Systems power_systems@sil.org Introduction Figure 1: View showing Villager III and dc dc adapter The Villager III Power Bank may be used to power devices that

### DIGITAL TEMPERATURE CONTROL

Fridge / Freezer / Warmer with DIGITAL TEMPERATURE CONTROL MODEL MHD13F-DM SPECIFICATION DESIGNATION OF PARTS MODEL CAPACITY OUTER DIMENSIONS INPUT RATING ( or FREEZER) (WARMER) REFRIGERANT WEIGHT MHD13F-DM

### MODEL 6010A 6 12 VOLT BATTERY CHARGER ASSOCIATE

MODEL 600A 6 VOLT BATTERY CHARGER ASSOCIATE IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This manual contains important safety and operating instructions for the battery charger you have purchased.

### PRO-WAVE INVERTER 12 VOLT, 150W PURE SINE WAVE

PRO-WAVE INVERTER 12 VOLT, 150W PURE SINE WAVE P/No. PW150 WARNINGS For use with negatively earthed vehicles & systems only. For indoor use only. Do not expose to rain. Hazardous voltages inside do not

### 24/3000H-3PH 24/4500H-3PH 24/6000H-3PH

Manufacturer of Dimensions TM Inverters 4467 White Bear Parkway St. Paul, MN 55110 Phone: 651-653-7000 Fax: 651-653-7600 E-mail: inverterinfo@sensata.com Web: www.dimensions.sensata.com 120015D OWNERS

### 10AMP FULLY AUTOMATIC 6V & 12V BATTERY CHARGER OWNER'S MANUAL

1244502 10AMP FULLY AUTOMATIC 6V & 12V BATTERY CHARGER OWNER'S MANUAL 1. IMPORTANT SAFETY INSTRUCTIONS 1.1 SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions. 1.2

### 6 hour run time. Crossover and Chest models:

How many AMPs/Watts can the CIC Powerbox provide? Each CIC Powerbox can supply a continuous amp/watt load of 17 amps of 115-volt AC power (2,000 watts), and can supply an initial amp/watt surge of over

### OWNER S MANUAL PORTABLE POWER COMPACT & ROBUST

52731 18 AMP-HOUR 12 VOLT OVERHEAT PROTECTION JUMP START OWNER S MANUAL PORTABLE POWER COMPACT & ROBUST 18 Amp-Hour, 12 Volt Wall charger 6-gauge booster cable Built in ultra-bright LED work light Safety

### AUTO CHARGE 12 AUTOMATIC BATTERY CHARGER

INSTRUCTION MANUAL FILE: 091-165-12 reve Rev: E, page 8 DATE: 7-02-15 AUTO CHARGE 12 AUTOMATIC BATTERY CHARGER MODEL #091-165-12 NOTE : This charger is designed for vehicles with a single battery and negative

### 24 VOLT AUTOMATIC BATTERY CHARGER PART NO

24 VOLT AUTOMATIC BATTERY CHARGER PART NO. 957732 AC Input: DC Output: Battery Type: Specifications 230 volts, 50 hertz, 3.5 amps, single-phase 24 volts, 20 amps initially tapering to 6 amps 24 volt, 12

### S600,S600R Series Pure Sine Wave Inverter User s Manual

S600,S600R Series Pure Sine Wave Inverter User s Manual Table of contents 1. Important Safety Information.... 1 1-1 General Safety Precautions...... 1 1-2 Batteries Precautions... 1 2. Features... 2 2-1

### Safety, Installation And Operating Instructions For The Following Battery Charger Models: i2412, i3612, i4809, i2425, i3625, and i4818

Safety, Installation And Operating Instructions For The Following Battery Charger Models: i2412, i3612, i4809, i2425, i3625, and i4818 IMPORTANT NOTICE: Please save and read these safety, operating and

### OBE, OBEXU, ON BOARD Battery Chargers

C O R P O R A T IO N O P E R A T I N G I N S T R U C T I O N S OBE, OBEXU, ON BOARD Battery Chargers INTRODUCTION: These chargers are designed for the permanent installation on battery powered vehicles

### OBAE, OBAEXU, ON BOARD Battery Chargers

C O R P O R A T IO N O P E R A T I N G I N S T R U C T I O N S OBAE, OBAEXU, ON BOARD Battery Chargers INTRODUCTION: The OBAE line of chargers are designed for the permanent installation on battery powered

### 12 amp RMS Battery Charger

12 amp RMS Battery Charger 83-5000-12 If faults cannot be remedied, contact the Helpline on 020 8391 6767 helpline@hilka.co.uk Manufactured under license by Hilka Pro Imports GUARANTEE This product is

### LESTRONIC II BATTERY CHARGER MODEL 19740

*01679* LESTRONIC II BATTERY CHARGER MODEL 19740 PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS For correct operation of the equipment, it is important to read and be familiar with this

### MMA 160S ARC/MMA WELDER OPERATION INSTRUCTIONS

www.r-techwelding.co.uk MMA 160S ARC/MMA WELDER OPERATION INSTRUCTIONS 2 Thank you for selecting the R-Tech MMA160S Inverter Arc Welder. The MMA160S has many benefits over traditional Arc welders, including

### PSE-12125A PSE-12175A PSE-12275A

DC-AC Inverters PSE-12125A PSE-12175A PSE-12275A Owner's Manual Please read this manual before operating your Inverter INDEX INDEX Safety Instructions... 2,3 Inverters - General Information... 4,5,6 Characteristics

### DieHard,. Battery Charger 1512 Amp Fully Automatic Microprocessor Controlled. Engine Starter 100 Amp. Model No

OWNER'S MANUAL DieHard,. Battery Charger 1512 Amp Fully Automatic Microprocessor Controlled Engine Starter 100 Amp Model No. 200.71224 CAUTION: Read all Safety Rules and Operating Instructions, and follow

### MULTI-FUNCTION POWER PACK

Item #30554 MULTI-FUNCTION POWER PACK INSTRUCTIONS The ROCKWOOD MULTI-FUNCTION POWER PACK is an amazingly powerful yet compact power source fully capable of starting a vehicle repeatedly as well as providing

### PURE SINE WAVE DC-AC INVERTER

AC POWER SOURCE PURE SINE WAVE DC-AC INVERTER MODELS: PST-100S-12A PST-100S-24A OWNER'S MANUAL Please read this manual before operating your inverter. INDEX INDEX Safety Instructions... 2,3 Inverters -

### OWNERS MANUAL JANUARY 2007 ISO

Manufacturer of Dimensions TM Inverters 4467 White Bear Parkway St. Paul, MN 55110 Phone: 651-653-7000 Fax: 651-653-7600 E-mail: inverterinfo@sensata.com Web: www.dimensions.sensata.com 121231B OWNERS

### Owner's Manual. 120 Watt DC-AC Inverter Pure Sine Wave PST-12S-12A. Please read this manual before using your inverter

120 Watt DC-AC Inverter Pure Sine Wave PST-12S-12A Owner's Manual Please read this manual before using your inverter 1INTRODUCTION Thank you for choosing to purchase our inverters. Our power inverter series

### OPERATOR S MANUAL. Portable Power 950. Model No

OPERATOR S MANUAL Portable Power 950 Model No. 28.71987 Read and follow all Safety Rules and Operating Instructions before Every Use of this Product. Save these instructions. Sears Brands Management Corporation,

### OWNER S MANUAL. CAUTION: Read all Safety Rules and Operating Instructions, and follow them with each use of this product.

OWNER S MANUAL Model OMAX-6A-1B Single Bank Charger With Quick Disconnect Model OMAX-12A-1B Single Bank Charger Model OMAX-25A-1B Single Bank Charger Model OMAX-50A-1B Single Bank Charger Model OMAX-40AS-3B

### Power your day-to-day when others are power-less. Humless Sentinel User s Guide.

Power your day-to-day when others are power-less. Humless Sentinel User s Guide www. User s Guide Contents Safety Instructions page 6 Meet The Power page 7 Charging Your Unit page 12 Powering Your Devices

### CONTENTS 1. INTRODUCTION SAFTY INSTRUCTION CABLE CONNECTION SYSTEM DESCRIPTION OPERATION... 9

USER MANUAL 1 CONTENTS 1. INTRODUCTION... 1 2. SAFTY INSTRUCTION... 3 3. CABLE CONNECTION... 4 4. SYSTEM DESCRIPTION... 5 5. OPERATION... 9 6. TROUBLE SHOOTING GUIDE... 25 7. OPERATION MODES..... 27 8.

### Installation and Operating Instructions (for chargers shown below)

Installation and Operating Instructions (for chargers shown below) For additional information please call our Technical Support Group 800.742.2740 PRO CHARGING SYSTEMS, LLC 1551 Heil Quaker Boulevard,

### Pure Sine Wave DC TO AC Power Inverter. User s Manual

Pure Sine Wave DC TO AC Power Inverter User s Manual Distributed by: Tech Brands by Electus Distribution 320 Victoria Road, Rydalmere NSW Australia Tel: 1300 738 555 Fax: 1300 738 500 www.techbrands.com

About Xantrex Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with products from 50 watt mobile units to one MW utility-scale systems for wind, solar, batteries,

### OWNER S MANUAL. BATTERY CHARGER 60/20/2 Amp Fully Automatic. 275/125 AMP ENGINE STARTER With Battery Tester

OWNER S MANUAL BATTERY CHARGER 60/20/2 Amp Fully Automatic 275/125 AMP ENGINE STARTER With Battery Tester Model No. 200.71232 CAUTION: Read all Safety Rules and Operating Instructions, and follow them

### USER MANUAL. GS Series Hybrid Inverter

USER MANUAL GS Series Hybrid Inverter CONTENTS ABOUT THIS MANUAL... 1 Purpose... 1 Scope... 1 IMPORTANT SAFETY INSTRUCTIONS... 1 General Precautions... 1 Personal Precautions... 2 INSTALLATION... 3 Unpacking