Operating Instructions & Parts Manual. 800 Watt Power Inverter. Model 54DC44A

Transcription

1 Operating Instructions & Parts Manual EN 800 Watt Power Inverter Model 54DC44A

2 PLEASE READ AND SAVE THESE INSTRUCTIONS. READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. PLEASE REFER TO BACK COVER FOR INFORMATION REGARDING DAYTON S WARRANTY AND OTHER IMPORTANT INFORMATION. Model #: 54DC44A _ Serial #: Purch. Date: Form 5S0000 / Printed in China RAL100/ 01 / Grainger International, Inc. All Rights Reserved

3 UNPACKING Contents: 800 Watt Inverter Cables with Clips (3x) 35 AMP Spade Fuses Inspect: After unpacking the tool, carefully inspect for any damage that may have occurred during transit. Check for loose, missing, or damaged parts. Shipping damage claims must be filed with the carrier. See General Safety Instructions on page 2, and Cautions and Warnings as shown. GETTING STARTED OPERATION TROUBLESHOOTING

4 GETTING STARTED OPERATION TROUBLESHOOTING GENERAL SAFETY INSTRUCTIONS CAUTION Do not use this inverter with a device which uses more than 800 watt power consumption. Make certain the wattage requirements are within the capacity of this inverter s output watt range. Do not connect to a 6 Volt or 24 Volt DC battery. Do not use an AC (115 volt) extension cord longer than 25 feet. Do not use a 12 Volt DC extension cord of any type or length. Start and run your vehicle hourly to prevent battery discharge. IMPORTANT: Power OFF the inverter and device(s) being used before engine start up. Do not exceed maximum input voltage of 15 Volt DC. WARNING This inverter must be connected only to a 12 Volt DC Negative Ground ignition system (most vehicles). Do not use this inverter with a Positive Ground vehicle ignition system. Consult your vehicle s owner s manual for ignition system identification. Do not connect inverter to a household or RV AC distributing circuit. Do not connect inverter to an AC load circuit in which the neutral wire is connected to ground or to negative ( ) of the DC battery power source. Improper use of this inverter can cause personal injury, property damage, and/or possible loss of life. Do not use or place this inverter near flammable materials or any location which accumulates flammable fumes. Do not operate this inverter in or near water. Do not operate inverter using wet hands. Do NOT touch the inverter clips immediately after usage. The clips may be hot and could cause minor burns. Disconnect power to the inverter when it is not in use. To avoid potential property damage, do not leave this inverter or any device operating unattended in a vehicle. Do not place this inverter in confined spaces or inside the battery compartment of a vehicle or boat. Use only in properly ventilated areas. Do not place item(s) over the inverter. Make sure that air is allowed to circulate freely around it. Do not place the inverter in direct sunlight or near any device which is generating heat above room temperature. Do not operate inverter in ambient air temperature below 32 F or above 104 F. Regularly check that all connections are secure and tight. A loose connection can create high electrical resistance and generate excessive heat which will damage the inverter. Not approved for use in conjunction with medical equipment. Reverse polarity connection will damage the inverter and possibly any connected equipment. Do not open the inverter housing case. Secure the inverter and device being operated to prevent them from moving while the vehicle is in motion. This is not a toy. Keep out of reach of children! 2 WARNING: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. NOTE: To achieve maximum inverter power output, user must run vehicle while inverter is in use. Keep these instructions for future reference. Start and run your vehicle hourly to prevent battery discharge.

5 Output voltage range VOLT AC Output current range Amps AC Output frequency (HZ) 60 HZ (+/- 3HZ) Max. Continuous power 800 Watt Surge capability (peak power) 1600 Watt/ 0.1 seconds Optimum efficiency 80% No load current draw 800 ma Wave form Modified Sine Wave Input voltage range Volts DC Input current range Amps DC Replaceable fuse (3X) 35 Amp - Spade Types AC Receptacles Dual 3 Prong Grounded USB port 5 Volt DC Amps GETTING STARTED Automatic electronic circuit features: A. High input voltage shutdown 15 Volt DC B. Low input voltage audible alarm 11 Volt DC C. Low input voltage shutdown 10.5 Volt DC D. Overload shutdown 840 Watt System display: A. System normal operation Green LED indicator B. Overload Red LED indicator C. Low/high battery Red LED indicator D. Over temperature Red LED indicator Environment operational conditions: A. Elevation (above sea level) 0 to 10,000 ft 0 to 3,048 m B. Operating 32 F to 104 F 0 C to 40 C C. Storage 32 F to 104 F 0 C to 40 C Physical: A. Inverter net weight 2.5 lbs 1.14 kgs. B. Dimensions (HXWXD) 2.89 X 4.89 X cm X cm X cm C. Clips power cable lenght cm OPERATION TROUBLESHOOTING Dry Location Use Only High Voltage Over Head Cover Keep Away From Fire Do Not Open 3

6 GETTING STARTED WARNING: Explosive GAS DANGER! Only make battery and ground connections in a well ventilated area. Battery Terminal Connection 1. Prior to connecting the inverter, make sure the inverter s ON/OFF rocker switch is in the OFF position. ON OFF 2. Attach the closed-round spade connector (red cable) to the red (+) input terminal on the inverter. 3. Attach the closed-round spade connector (black cable) to the black ( ) input terminal on the inverter. 4. Hand tighten both terminals to secure cables to input terminal using screws with rounded groove heads. Do not over-tighten. 5. Connect the red alligator clip to the vehicle battery s positive (+) terminal. 6. Connect the black alligator clip to the vehicle s chassis, engine block or a nonmoving grounded metal part of vehicle as far away from the battery as possible. 800 Watt Inverter Positive (+) Terminal Red Cable Black Cable OPERATION TROUBLESHOOTING 4 Red (+) Input Terminal Black ( ) Input Terminal Earth Ground Terminal Red Alligator Clip Black Alligator Clip Black Alligator Clip to Chassis Ground Vehicle Battery Earth Ground Connection CAUTION: Ensure the ground rod is properly buried according to local electrical codes. 1. Locate the inverter earth ground terminal (400 watt inverter rear panel). 2. Loosen the earth ground terminal hex nut by turning the hex nut counter-clockwise. 3. Connect one bare end of a #18 AWG ground wire (not included) onto the ground terminal and tighten the hex nut. 4. Connect the other bare end of the ground wire to the ground rod. NOTE: Make sure ground wire length is longer than the distance from the inverter to the ground rod to achieve a secure connection.

7 System normal operation... Green LED Indicator Over voltage... Red LED Indicator Over load... Red LED Indicator Low battery... Red LED Indicator Over temperature... Red LED Indicator Determine power requirement To determine maximum power required, add up the wattage of all devices to be operated with this inverter simultaneously. If the wattage of the device(s) is not available, but the current draw (amp) is given, simply convert to wattage using this formula: GETTING STARTED VOLT (V) X AMP (A) = WATT (W) EXAMPLE: 110 VOLT X 7 AMP = 770 WATT OPERATION TROUBLESHOOTING 5

8 GETTING STARTED OPERATION AND USAGE Inverter Operation 1.Prior to plugging in the device, make sure the device is OFF. 2.Connect the device s electrical plug into the inverter receptacle. 3.Turn the inverter ON/OFF switch, to ON position. If the inverter is working properly, a green LED indicator on the front panel will light. Now turn on the device(s). If the green indicator remains ON, then the system is operating properly. If inverter alarm sounds or red LED indicator light turns ON, turn OFF the device(s), then turn OFF the inverter immediately. See the trouble shooting guide. The inverter may have been over loaded or the input voltage may be too low. IMPORTANT: To achieve inverter maximum power output, user must run vehicle while the inverter is in use. OPERATION CAUTION: Some rechargeable devices are equipped with a separate charger, which can be connected into this inverter s AC receptacle(s). Westward inverters are engineered to be used with these products. However, certain rechargeable devices are manufactured with built-in chargers (see device s owner s manual). This category of devices may cause internal damage to inverters and should not be used with this inverter. The temperature of device(s) must be monitored for first 15 minutes of operation. Abnormally elevated temperature of device(s) is an indication that they should not be used with this inverter. USB Port Operation 1.Connect your cell phone or any other battery powered device that can be charged or powered via a USB terminal into the 800 watt inverter USB power port. Make sure the device s USB connector plug is properly seated into the 800 watt inverter USB power port. TROUBLESHOOTING 2. Your USB powered device with built-in battery(s) will start charging automatically. 3. Power on and operate your device as needed. 4. To stop charging or powering your USB powered device, switch off the USB power device. 5. Disconnect your device from the 800 watt inverter USB power port. 6 NOTE: The USB port does not support data transfer. It will only power and/or recharge USB personal devices.

9 OPERATION AND USAGE Action Typical Use and Wattage This listing is for reference purposes only. Some devices exceed the wattages listed. Before using the device refer to the device s owner s manual for actual wattage required. Not recommended for use with inductive loads, such as fluorescent lamps, compressors, motors & pumps. Video Game Console Nintendo DSi, DSL, DS...5 watt Sony PSP...6 watt Wii U...35 watt Wii w/ game screen...75 watt Xbox ONE console watt PS4 console watt Office Equipment Tablets watt Portable printer...55 watt Portable scanner...55 watt Portable fax...60 watt Desktop printer watt Laptop computer watt PC & monitor watt Business printer watt Laser jet copier watt Electronics Digital cameras...3 watt Cellular phones watt ipod /MP3 player...5 watt Blu-Ray...18 watt Cellular phone charger...30 watt DVD player watt 32 LED / LCD TV watt 55 LED / LCD TV watt 60 plasma TV watt Sound system watt Tools Cordless drill charger...15 watt Spot light / Work light watt 1/4 hp buffer watt Soldering gun watt 1/2 hp pump watt Jig saw watt Bench top saw* watt Round sander* watt Band saw* watt * Check peak power required to use these devices. 7 GETTING STARTED OPERATION TROUBLESHOOTING

10 GETTING STARTED TROUBLESHOOTING Symptom Possible Cause(s) Corrective Lack of power output. 1. Power source voltage below 10 Volt. 1. Recharge battery or replace power supply. 2. Excessive current drawn by the device(s) being operated. 2. Reduce load to maximum 800 watt. 3. Inverter not completely warmed up. 3. Power Off the AC device(s) and inverter. Disconnect the device(s) connected to the inverter. Turn the inverter on & leave running for a minimum of 2 minutes. Power off the inverter and quickly plug in the device(s) to the inverter making sure the device(s) is/are off. Power on the inverter and the device(s). Low battery alarm on all the time. 4. Inverter fuse(s) is/are blown. 1. Inadequate power or excessive voltage drop. 2. Poor battery condition. 4. Replace blown fuse(s) with (3) x 35A. TO REPLACE: Locate fuse on inverter s rear compartment. Remove fuse(s) with needle nose pliers & replace with equivalent 35A fuse(s). 1. Check and connect inverter for proper clip connection to the battery s power source. 2. Start the engine to recharge the battery. Ensure the inverter is powered off before starting engine. Replace battery if required. OPERATION Red light on. 1. Inverter is overloaded. 2. Inverter voltage below 10.5 Volt. 3. Over recommended temperature. 1. Replace load to maximum of 800 watt. 2. Charge or replace battery. 3. Turn Off inverter and ensure operartion temperature is between 32ºF - 104ºF. TROUBLESHOOTING Television/ power tool will not start. Television interference. Static/noise interference in audio system. 1. High surge wattage is required to start-up the device. Picture breaking up (snow) Sound system has weak alternating current shielding. Toggle the inverter power switch in succession a total of 5 times in order to generate the necessary power to start the device. If the device does not power on or start up in 5 cycles of on/off trials, this inverter will not work with the device. 1. Place the inverter as far as possible from TV, the antenna and the coaxial cable. TV station may be out of range. 1. Do not use inverter with low quality audio system AC current shielding. 2. Replace audio system with high quality noise filtering. Fuse blown. 8 Reverse battery polarity connection. Turn off inverter and AC voltage device. Disconnect inverter from battery power source. Replace fuse as stated above. Reconnect inverter to proper battery polarity.

11 MAINTENANCE & Maintenance Some rechargeable devices are equipped with a separate charger, which can be connected into this inverter power receptacle. Westward inverters are engineered to be used with these products. However, certain rechargeable devices are manufactured with built-in chargers (see device s owner s manual). This category of devices may cause internal damage to inverters and should not be used with this inverter. The temperature of device must be monitored for the first 15 minutes of operation. Abnormally elevated temperature of the device is an indication that they should not be used with this inverter. Power Source This inverter must be connected to a 12 Volt DC Negative Ground ignition system battery in good condition. Most vehicles are negative ground systems (see the vehicle'sowner s manual for ignition system identification). Do not connect this inverter to a 6 or 24 Volt battery system. Do not use this inverter with a positive ground vehicle to avoid damage to the inverter. GETTING STARTED PARTS LIST Ref. No. Description Part Number 1 For Repair Parts, call GRAINGER 24 hours a day 365 days a year Please provide following information: Model number Serial number (if any) Part description and number as shown in parts list 35 AMP spade fuse N/A Qty. 3 OPERATION TROUBLESHOOTING 9

12 WESTWARD ONE-YEAR LIMITED WARRANTY WESTWARD ONE-YEAR LIMITED WARRANTY. All Westward product models covered in this manual covered by this Limited Warranty are warranted by W.W. Grainger, Inc. ( Grainger ) to the original user against defects in workmanship or materials under normal use for one year after date of purchase. If the Product is part of a set, only the portion that is defective is subject to this warranty. Any Product or part which is determined to be defective in material or workmanship and returned to an authorized service location, as Grainger or Grainger s designee designates, shipping costs prepaid, will be, as the exclusive remedy, repaired or replaced with a new or reconditioned product or part of equal utility or a full refund given, at Grainger s or Grainger s designee s option, at no charge. For limited warranty claim procedures, see Warranty Service below. COVERED PRODUCTS. This Limited Warranty covers the product model(s) identified in this manual. This Limited Warranty does not cover normal wear and tear of Products or portions of them, or products or portions of them which are consumable in normal use. This warranty is void if there is evidence of misuse, mis-repair, mis-installation, abuse or alteration. WARRANTY DISCLAIMERS AND LIMITATIONS OF LIABILITY RELATING TO ALL CUSTOMERS FOR ALL PRODUCTS LIMITATION OF LIABILITY. TO THE EXTENT ALLOWABLE UNDER APPLICABLE LAW, GRAINGER S LIABILITY FOR CONSEQUENTIAL AND INCIDENTAL DAMAGES IS EXPRESSLY DISCLAIMED. GRAINGER S LIABILITY IN ALL EVENTS IS LIMITED TO AND SHALL NOT EXCEED THE PURCHASE PRICE PAID. WARRANTY DISCLAIMER. A DILIGENT EFFORT HAS BEEN MADE TO PROVIDE PRODUCT INFORMATION AND ILLUSTRATE THE PRODUCTS IN THIS LITERATURE ACCURATELY; HOWEVER, SUCH INFORMATION AND ILLUSTRATIONS ARE FOR THE SOLE PURPOSE OF IDENTIFICATION, AND DO NOT EXPRESS OR IMPLY A WARRANTY THAT THE PRODUCTS ARE MERCHANTABLE, OR FIT FOR A PARTICULAR PURPOSE, OR THAT THE PRODUCTS WILL NECESSARILY CONFORM TO THE ILLUSTRATIONS OR DESCRIPTIONS. EXCEPT AS PROVIDED BELOW, NO WARRANTY OR AFFIRMATION OF FACT, EXPRESSED OR IMPLIED, OTHER THAN AS STATED IN THE LIMITED WARRANTY ABOVE IS MADE OR AUTHORIZED BY GRAINGER. PRODUCT SUITABILITY. MANY JURISDICTIONS HAVE CODES AND REGULATIONS GOVERNING SALES, CONSTRUCTION,, AND/OR USE OF PRODUCTS FOR CERTAIN PURPOSES, WHICH MAY VARY FROM THOSE IN NEIGHBORING AREAS. WHILE ATTEMPTS ARE MADE TO ASSURE THAT PRODUCTS COMPLY WITH SUCH CODES, GRAINGER CANNOT GUARANTEE COMPLIANCE, AND CANNOT BE RESPONSIBLE FOR HOW THE PRODUCT IS INSTALLED OR USED. BEFORE PURCHASE AND USE OF A PRODUCT, REVIEW THE, AND ALL APPLICABLE NATIONAL AND LOCAL CODES AND REGULATIONS, AND BE SURE THAT THE PRODUCT,, AND USE WILL COMPLY WITH THEM. CONSUMERS ONLY. CERTAIN ASPECTS OF DISCLAIMERS ARE NOT APPLICABLE TO CONSUMER PRODUCTS SOLD TO CONSUMERS; (A) SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU; (B) ALSO, SOME JURISDICTIONS DO NOT ALLOW A LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU; AND (C) BY LAW, DURING THE PERIOD OF THIS LIMITED WARRANTY, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO CONSUMER PRODUCTS PURCHASED BY CONSUMERS, MAY NOT BE EXCLUDED OR OTHERWISE DISCLAIMED. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. THIS LIMITED WARRANTY ONLY APPLIES TO PRODUCTS PURCHASED BY UNITED STATES PURCHASERS FOR DELIVERY IN THE UNITED STATES. WARRANTY SERVICE To obtain warranty service if you purchased the covered product directly from Grainger, (i) write or call or visit the local Grainger branch from which the product was purchased or another Grainger branch near you (see for a listing of Grainger branches); or (ii) contact Grainger by going to com and clicking on the Contact Us link at the top of the page, then clicking on the us link; or (iii) call Customer Care (toll free) at To obtain warranty service if you purchased the covered product from another distributor or retailer, (i) go to for Warranty Service; (ii) write or call or visit a Grainger branch near you; or (iii) call Customer Care (toll free) at In any case, you will need to provide, to the extent available, the purchase date, the original invoice number, the stock number, a description of the defect and anything else specified in this Westward One-Year Limited Warranty. You may be required to send the product in for inspection at your cost. You can follow up on the progress of inspections and corrections in the same ways. Title and risk of loss pass to buyer on delivery to common carrier, so if product was damaged in transit to you, file claim with carrier, not the retailer or Grainger. For warranty information for purchasers and/or delivery outside the United States, please contact: Canada: Mexico: Grainger.com.mx Location not listed, contact: (or GRAINGER) DM_US