Merkel Guide Ring Guivex SBK
|
|
- Esmond Benson
- 6 years ago
- Views:
Transcription
1 Product description Guide rings for piston rods can be used for very heavy loads in hydraulics. The profiling (patented) on the static side of the guide ring ensures an even distribution of stress. Product advantages Merkel guide ring SBK offers clear advantages against conventional guide strips and guide rings: replace costly metal guides the lateral forces are evenly distributed along the length of the guide ring; as a result large radial loading possible no stress peaks in the area of the edge no edge breaks optimal utilisation of guide length permits a shorter length and the overload limit is much higher the stress distribution in the contact zone encourages the entry of hydraulic oil between the guide ring and the contact area the total friction and wear are considerably reduced patented product design (patent-no. PCT/ EP95/03874) Application Mobile hydraulics, heavy duty hydraulics. Diameter 300 Designation Fabric-base laminate GW G517 Diameter > 300 Fabric-base laminate Designation Operating conditions Temperature range in C GW G517/ ydraulic oils L, LP Temperature range in C GW G517/ Water ETG (rapeseed oil) FA fluids FB fluids FC fluids EES (synthetic esters) EPG (glycol) Mineral greases FD fluids
2 Rod Seals Surface quality Surface roughness R a R max Sliding surface 0,05 0,3 mm 2,5 mm Groove base 2 mm 10 mm Groove flanks 3 mm 15 mm Percentage contact area M r >50% up to max. 90% at cutting depth c = Rz/2 and reference line C ref = 0%. Design notes Please observe our general design notes in Simrit Standard Catalogue, Merkel ydraulics Technical Principles. Tolerance recommendation D 1 8 The tolerance recommendation for dimensions D and df must be regarded in conjunction with the seal being used. The diameter d1 stated in the dimensional table must be seen solely with reference to the guide ring. The corresponding diameter of an adjacent seal installation space must be matched to the sealing element involved. Manufacturing tolerance Profile thickness S 0,01 0,06 Surface load p <80 N/mm² up to 60 C For sliding speed, see sealing system. p <40 N/mm² up to 100 C Surface force The distribution of compression on the guide bushings is not linear. When determining the permissible specific compression per unit area, the non-linear characteristic of the compression over the contact area has been taken into account The permissible loading on the guide strip is calculated by multiplying the projected area by the permissible specific compression per unit area. The depiction here shows the ideal case with parallel loading. The figure given for the permissible specific compression per unit area, however, takes into account the possible angular offset of rod or piston when the recommended guide elements are used. F F F = P x A A = d x = guide strip width F = radial loading A = projected area P = perm. compression per unit area d = rod diameter with rod guidance; piston diameter with piston guidance 2
3 Article list d D F D F1 Profile L GW G ,6 2,5 9,7 9, ,6 2,5 9,7 9, ,6 2,5 9,7 9, ,6 2, , ,6 2,5 9,7 9, ,6 2,5 9,7 9, ,6 2, , ,6 2, , ,6 2,5 9,7 9, ,6 2,5 9,7 9, ,6 2, , ,6 2,5 9,7 9, ,5 4, , ,6 2,5 9,7 9, ,6 2, , ,6 2, , ,6 2, , ,6 2,5 9,7 9, ,5 4, , ,6 2, , ,6 2, , ,5 4, , ,6 2, , ,6 2, , ,6 2, , ,6 2, , ,6 2, , ,6 2, , ,5 4, , ,5 4, , ,6 2, ,
4 Rod Seals d D F D F1 Profile L GW G ,6 2, , ,6 2, , ,6 2, , ,6 2, , ,6 2, , ,6 2, , ,6 2, , ,5 4, , ,6 2, , ,6 2, , ,6 2, , ,5 4, , ,6 2, , ,6 2, , ,5 4, , ,6 2, , ,5 4, , ,6 2, , ,6 2, , ,5 4, , ,6 2, , ,6 2, , ,6 2, , ,6 2, , ,5 4, , ,6 2, , ,5 4, , ,6 2, , ,6 2, , ,6 2, , ,5 4, , ,5 4, ,
5 d D F D F1 Profile L GW G ,6 2, , ,6 2, , ,6 2, , ,6 2, , ,6 2, , ,5 4, , ,6 2, , ,6 2, , ,6 2, , ,6 2, , ,5 4, , ,5 4, , ,6 2, , ,6 2, , ,5 4, , ,6 2, , ,5 4, , ,5 4, , ,5 4, , ,6 2, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,6 2, , ,6 2, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,6 2, ,
6 Rod Seals d D F D F1 Profile L GW G ,5 4, , ,5 4, , ,5 4, , ,6 2, , ,5 4, , ,5 4, , ,6 2, , ,6 2, , ,6 2, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,6 2, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,6 2, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,6 2, ,
7 d D F D F1 Profile L GW G ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,5 4, , ,6 1633,6 1628,1 4, , ,5 4, , Ordering example Type d D F L SBK Fabric-base laminate
Operating conditions. Surface roughness R a R max
Merkel U-Ring NI 300 Merkel U-Ring NI 300 Asymmetrical sealing lips PUR profile ring Sealing edge Material Material Code Hardness Polyurethane 94 AU 925 94 Shore A Operating conditions Material 94 AU 925
More informationMerkel Compact Seal S 8
Merkel Compact Seal S 8 Merkel Compact Seal S 8 Material Rubber head Fabric part Material Code Hardness Nitrile rubber NBR 70 NBR B209 70 Shore A Operating conditions Fig. 1 Merkel Compact Seal S 8 Product
More informationMerkel U-Ring Seal Set 0216
Merkel U-Ring Seal Set 0216 Merkel U-Ring Seal Set 0216 NBR U-ring Backring Fabric U-ring NBR Cotton fabric Code 80 NBR B246 BI-NBR B4 B248 Back-up ring Fig. 1 Merkel U-Ring Seal Set 0216 Product description
More informationMerkel U-Ring NI 300. Hydraulics Rod Seals Merkel U-Ring NI 300. Merkel U-Ring NI 300. Material. Operating conditions. Product description
Merkel U-Ring NI 300 Merkel U-Ring NI 300 Asymmetrical sealing lips PUR profile ring Sealing edge Material Material Code Hardness Polyurethane 94 AU 925 94 Shore A Operating conditions Material 94 AU 925
More informationMerkel Double Wiper PT 2
Merkel Double Wiper PT 2 Merkel Double Wiper PT 2 Material O-rings Profile ring Profile ring Material PTFE bronze compound Code PTFE B602 Fig. 1 Merkel Double Wiper PT 2 O-ring Material Code Hardness Nitrile
More informationØ range <500 mm. Ø range >500 mm. Operating conditions. Surface quality. Surface roughness R a R max
Hyraulics Ro Seals Merkel U-Ring T 20 Merkel U-Ring T 20 Merkel U-Ring T 20 PUR profile ring Material range
More informationOther materials are available on request. Operating conditions
Merkel U-Ring T 18 Merkel U-Ring T 18 Asymmetrical sealing lip POM back-up ring PUR profile ring Profile ring Coe Harness Polyurethane 95 AU V142 95 Shore A Fig. 1 Merkel U-Ring T 18 Back-up ring Polyacetal
More informationDynamic Elements Linear Slides Mechanical Drive Elements Accessories for Mechanical Drive Elements
8 Dynamic Elements Mechanical Drive Elements Accessories for Mechanical Drive Elements The Dynamic Elements product group of the MB Building Kit System contains components which enable precise linear movement.
More informationMerkel PTFE U-rings. for high level applications
Merkel PTFE U-rings for high level applications Product information Merkel PTFE U-rings Simrit, Your Global Technology Specialist for Seals and Vibration Control Simrit, Your Global Technology Specialist
More informationMerkel PRW 1 Double Wiper with Integrated Pressure Relieve. Product Information Merkel Hydraulics
Merkel PRW 1 Double Wiper with Integrated Pressure Relieve Product Information Merkel Hydraulics Simrit, Your Global Technology Specialist for Seals and Vibration Control Simrit, Your Global Technology
More informationMerkel Sealing Technology for the Ferrous & Non-Ferrous Processing Industries
Merkel Sealing Technology for the Ferrous & Non-Ferrous Processing Industries Merkel Heavy Industry 2 Merkel Sealing Technology Seals and Sealing Systems for the Ferrous & Non-Ferrous Processing Industries
More informationZURCON L-CUP. - Single Acting - Innovative Design based on U-Cup - Low Friction Properties - Material - Polyurethane Busak+ Shamban
contents (catalogue) main menu product range fullscreen/variable R ZURCON L-CUP - Single Acting - Innovative Design based on U-Cup - Low Friction Properties - Material - Polyurethane 81 82 Zurcon R L-Cup
More informationMerkel Sealing Technology for the METALLURGICAL INDUSTRY. Freudenberg Sealing Technologies
Merkel Sealing Technology for the METALLURGICAL INDUSTRY Freudenberg Sealing Technologies 2 Merkel Sealing Technology for the METALLURGICAL INDUSTRY Installation recommendations for sealing systems plus
More informationCourtesy of CMA/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800)
01_1 Miniature st Headline_36 Ball Rail pt/14.4 Systems mm second line 2 Linear Motion and Assembly Technologies Miniature Ball Rail Systems Ball Rail Systems Roller Rail Systems Linear Bushings and Shafts
More informationBall Rail Systems RE / The Drive & Control Company
Ball Rail Systems RE 82 202/2002-12 The Drive & Control Company Rexroth Linear Motion Technology Ball Rail Systems Roller Rail Systems Standard Ball Rail Systems Super Ball Rail Systems Ball Rail Systems
More informationProfi le rail guides LLR
Profi le rail guides LLR Content The SKF brand now stands for more than ever before, and means more to you as a valued customer. While SKF maintains its leadership as the hallmark of quality bearings throughout
More informationTurcon Glyd Ring. Double Acting Rubber Energized Plastic Faced Seal Material: Turcon, Zurcon and Elastomer
Turcon Glyd Ring Double Acting Rubber Energized Plastic Faced Seal Material: Turcon, Zurcon and Elastomer 15 Turcon Glyd Ring 16 Turcon Glyd Ring Turcon Glyd Ring Description Successfully used for decades,
More informationFor advanced drive technology CLAMPEX. Shaft-Hub-Connection. KTR Precision Joints CLAMPEX
technology CLAMPEX Shaft-Hub-Connection CLAMPEX KTR Precision Joints 07 technology Table of contents Page Brief information 09 Selection and calculation -5 CLAMPEX -Selection Shaft diameter = d 0 10 0
More informationMerkel Guide Ring Guivex SBK, KBK Reliable guides for rods and pistons. Product Information Merkel Hydraulics
Merkel Guide Ring Guivex SBK, KBK Reliable guides for rods and pistons Product Information Merkel Hydraulics Simrit, Your Global Technology Specialist for Seals and Vibration Control Simrit, Your Global
More information10 Thrust ball bearings
10 Thrust ball bearings Designs and variants.............. 1010 Single direction thrust ball bearings... 1010 Double direction thrust ball bearings.. 1010 Cages............................ 1010 Bearings
More informationNEW. Cone Clamping Elements Trantorque Keyless Locking Devices for very small diameters from 3 mm. E03.050e
Cone Clamping Elements Trantorque Keyless Locking Devices for very small diameters from 3 mm NEW E03.050e Backlash free positioning Excellent concentricity Quick mounting by central clamping nut Issue
More informationMERKEL P7 Wiper Single-acting rod wiper made from Polyurethane with integrated metal retainer. PUR wiper for axial-accessible housings.
Página 1 de 5 PT 1 MERKEL PT 1 Low Friction Wiper Low friction wiper consisting of one profile ring with a sealing edge and a wiper edge, as well as two O-Rings as pre-load components. A wiper for improvement
More informationMiniature Ball Rail Systems
R310EN 2210 (2004.06) The Drive & Control Company 2 Bosch Rexroth AG Linear Motion and Assembly Technologies Miniature-BRS R310EN 2210 (2004.06) Linear Motion Systems Ball Rail System Standard Ball Rail
More informationRelubricable bushings Technical catalogue
Relubricable bushings Technical catalogue 11 RL - RELUBRICABLE BEARING WITH STEEL SUPPORT 1 2 3 4 1. Polyacetal Resin 0,30-0,50 mm. 2. Porous bronze without lead 0,20-0,30 mm. 3. Steel strip 0,40-2,20
More informationSHAFT SEALS WITH PTFE COATING TCJ
SHAFT SEALS WITH PTFE COATING TCJ DESCRIPTION The TCJ profile is a shaft seal composed of a single metal cage with a rubber coating, PTFE-coated double sealing lip and integrated spring. ADVANTAGES Very
More informationOperating conditions. * Surface roughness of the sliding surface to suit the sealing component used.
Merkel Wiper P 6 Merkel Wiper P 6 Material Wiper lip Material Code Hardness Nitrile rubber NBR 85 NBR B247 85 Shore A Fluoro rubber FKM 85 FKM K664 85 Shore A Operating conditions Fig. 1 Merkel Wiper P
More informationGuide plate. Fig. 1 Construction of Slide Pack Type FBW-RUU
A Slide Pack Slide Pack Type FBW Japanese patent No. 1696446 Overseas patent resistered in the U.S. Mounting plate Ball Slide rail Seal Guide plate Stopper Fig. 1 Construction of Slide Pack Type FBW-RUU
More informationBallscrews / Linear Guideway General Catalog
Ballscrews / inear Guideway General Catalog inear Guideway 2 Introduction of ach Series 2. eavy oad Type, MSA Series A. Construction Upper Retainer Carriage nd Seal nd Cap Rail Grease Nipple Ball 45 ower
More informationSTANDARD SHAFT SEALS VB
STANDARD SHAFT SEALS VB DESCRIPTION The VB profile is a shaft seal composed of a single external metal cage with an internal rubber coating and a primary sealing lip without a spring. ADVANTAGES Good radial
More informationIntroduction of Each Series
12 Introduction of Each Series 12.1 eavy Load Type, MSA Series A. Construction LINEAR GUIDEWAY Upper Retainer Carriage End Cap End Seal Grease Nipple Ball Lower Retainer Rail 45 eavy Load Type, MSA Series
More informationSTANDARD SHAFT SEALS VC
STANDARD SHAFT SEALS VC DESCRIPTION The VC profile is a shaft seal composed of a single metal cage with a rubber coating and a primary sealing lip without a spring. ADVANTAGES Very good static sealing
More informationHydraulic fluid power Cylinders Dimensions and tolerances of housings for single-acting piston and rod seals in reciprocating applications
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 5597 ISO/TC 131/SC 7 Secretariat: JISC Voting begins on: 2018 01 29 Voting terminates on: 2018 03 26 Hydraulic fluid power Cylinders Dimensions and tolerances
More informationKANTSEAL. -Axial sealing - -Elastomers-
KANTSEAL -Axial sealing - -Elastomers- 61 62 n Description The Kantseal is agood alternative to the O Ring as an axial static seal in cases where particular demands are made. The application and handling
More informationIntermot Hydraulic Motors. Drum Brakes RC Series
Intermot Hydraulic Motors Drum Brakes RC Series TECHNICAL CATALOGUE INDEX General information Pag. 10 Technical data Pag. 14 Dimensional drawings Pag. 15 Ordering instructions Pag. 17 9 Hydraulic fluids
More informationR310EN 2211 ( ) The Drive & Control Company
eline Ball Rail Systems R310EN 2211 (2006.04) The Drive & Control Company Bosch Rexroth AG Linear Motion and Assembly Technologies Ball Rail Systems Roller Rail Systems Linear Bushings and Shafts Ball
More informationHydraulic cylinder Type CDL1
Industrial Hydraulics Electric Drives and Controls Linear Motion and Assembly Technologies Pneumatics Service Automation Mobile Hydraulics RE 17 325/01.03 Replaces: 07.02 Hydraulic cylinder Type CDL1 Series
More informationSTANDARD SHAFT SEALS SC
STANDARD SHAFT SEALS SC DESCRIPTION The SC profile is a shaft seal composed of a single metal cage with a rubber coating and a primary lip with integrated spring. ADVANTAGES Very good static sealing Very
More informationCompact Modules. with ball screw drive and toothed belt drive R310EN 2602 ( ) The Drive & Control Company
with ball screw drive and toothed belt drive R310EN 2602 (2007.02) The Drive & Control Company Bosch Rexroth AG Linear Motion and Assembly Technologies Ball Rail Systems Roller Rail Systems Linear Bushings
More informationPRODUCT OVERVIEW HIGHEST PRECISION
PRODUCT OVERVIEW If you need high precision gear reducers at a reasonable cost and you value innovation and excellent service, take a close look at our product line. You ll find a wide range of products
More informationRound Fine Centering for the mold construction. The development. Advantages
Round Fine Centering for the mold construction The development Advantages Durability: for mass production Backlash-free for very precise mold alignment Shorter cycle times High initial load capacity at
More informationCompact Seal. DUOPAC rubber fabric reinforced compact seals Type DPS and DPC. Busak+ Shamban
DUOPAC rubber fabric reinforced compact seals Type DPS and DPC Description The compact seals DUOPAC DPS and DPC types are double acting piston seals with integrated guide rings. DUOPAC has been designed
More informationG max rad Ød 2 Ød 3 ØD to to to to
Design Hallite 506 bearing strip is available in three forms: cut rings, spiral lengths and flat coils. Hallite 506 provides an extremely effective, hard wearing and easy to use bearing material. Manufactured
More information1 Mounting V-belt drive (motor pulley, fly wheel, V-belts and guard)
Mounting V-belt drive (motor pulley, fly wheel, V-belts and guard) General safety instructions, requirements and procedures 1 Mounting V-belt drive (motor pulley, fly wheel, V-belts and guard) 1.1 General
More informationDesign. Dynamic Sealing Face Ød1,ØD max Static Sealing Face Ød2,ØD2, L1 3.2 max 16 max 125 max 140 max
Design Hallite 506 bearing strip is available in three forms: cut rings, spiral lengths and flat coils. Hallite 506 provides an extremely effective, hard wearing and easy to use bearing material. Manufactured
More informationTurcon RotoGlydRing. Latest information available at Edition August
Turcon RotoGlydRing 241 242 Turcon Roto Glyd Ring n TURCON ROTARY SEALS - ELASTOMER ENERGIZED n Turcon Roto Glyd Ring Description The Turcon Roto Glyd Ring is used to seal rods, shafts, axles, bores, rotary
More informationHydraulic cylinders type CC - round heads with counterflanges to ISO nominal pressure 25 MPa (250 bar) - max 32 MPa (320 bar)
www.atos.com Table B-/E Hydraulic cylinders type CC - round heads with counterflanges to ISO 60 - nominal pressure MPa (0 bar) - max MPa (0 bar) SWC Cylinders Designer Software for assisted selection of
More informationStainless Steel Couplings, Universal Joints & Shaft Accessories
Stainless Steel Couplings, Universal Joints & Shaft Accessories E SSFC Series - Insert (3 Jaw) Type Coupling 316 stainless steel with passivated finish Precision machined bore or solid hubs Three types
More informationBEARING Polyester Fabric, Rod and Piston and Coil
ØD ØD 3 Ød 1 Ød Ød 3 ØD 1 506 BEARIN Polyester Fabric, Rod and Piston and Coil DEIN The Hallite 506 bearing strip is designed to provide an extremely effective, hard wearing, and easy-to-use bearing solution
More informationStatic and dynamic oil compatibility tests for Freudenberg radial shaft seals to release the usage in FLENDER-gear units applications (Table T 7300)
- Page of 8 Test Documentation This document is a translation of Freudenberg Sealing Technologies (FST) internal test procedure FB 7 008. In case both documents contradict each other, the iginal German
More information12.5 Ball Chain Type, SME Series
12.5 Ball Chain Type, SME Series A. Construction Carriage End Cap End Seal Grease Nipple Inner Seal Ball Bottom Seal Ball Chain 45 Rail 45 B. Characteristics The ball chain type linear guideway, SME series,
More informationORIGA SYSTEM PLUS Guides, Brakes and Valves for Modular Linear Drive Systems OSP Appendix to the Operating Instructions
ORIGA SYSTEM PLUS Guides, Brakes and Valves for Modular Linear Drive Systems OSP Appendix to the Operating Instructions TAll personnel who have anything to do with the OSP fitted with guides, brakes or
More informationVERLON No Swell Wear Rings
VERLON No Swell Wear Rings Ultra precision +.001 tolerance on cross section NO SWELL - Lowest friction Strength to 40,000 PSI Large range of widths, cross sections and diameters - metric too Features &
More informationFlexible Couplings 44
Flexible Couplings 44 RINGSPANN Registered Trademark of RINGSPANN GmbH, Bad Homburg MTY (81) 83 54 10 18 Why RINGSPANN Flexible Couplings? No connection of shafts without clutches It is a well-known fact
More informationCSM Crown T.M. Seal MACROTECH POLYSEAL, INC. 1/97 PATENT NO. 4,190,259
CSM-1000 Crown T.M. Seal MACROTECH POLYSEAL, INC. PATENT NO. 4,190,259 1/97 Crown Seal DESCRIPTION The Crown Seal is a squeeze-type seal. An O-ring is used as a loading spring and to seal the static surface.
More informationP54 PISTON SEAL TECHNICAL DETAILS. Part Number Structure. Double-Acting F E A T U R E S P54 M R N HLX. Compact piston design.
PISTON SEAL Double-Acting TECHNICAL DETAILS The Hallite P54 is a double-acting, o-ring energized, low-friction piston seal that performs well in both high- and low-pressure systems. High-performance Armorlene
More informationSeries 45 anti-rotation guide units
> Series 45 guide units CATALOGUE > Release 8.7 Series 45 anti-rotation guide units For cylinders DIN/ISO 6432 - ø2, 6, 20, 25mm For cylinders DIN/ISO 643 - ø32, 40, 50, 63, 80, 00mm» To be used with VDMA/
More informationNational Enduralube Bearings
Bearings The Worlds Most Reliable Bronze Bearing w w w. n ationalbronze.com National Bronze Mfg. Co. 800-875-3558 (Toll Free) 586-791-9044 (Fax) INTRODUCTION Since 1911 National Bronze Mfg. Co. has been
More information2006 MINI Cooper ENGINE Engine - Technical Data - Cooper (W10) & Cooper S (W11) Engine - Technical Data - Cooper (W10) & Cooper S (W11)
ENGINE, GENERAL 11 00 ENGINE IN GENERAL 2002-08 ENGINE Engine - Technical Data - Cooper (W10) & Cooper S (W11) ENGINE IN GENERAL Cylinder 4 Bore mm 77 (3.03) Stroke mm 85.8 (3.377) Effective displacement
More informationCylindrical roller bearings
Cylindrical roller bearings Cylindrical roller bearings are manufactured in a various range of constructive types and sizes, particularly single row cylindrical roller bearings but also two or more row
More informationHighly Flexible Couplings ELPEX-B Series
Siemens AG 2015 Highly Flexible Couplings ELPEX-B Series /2 Overview /2 Benefits /2 Application /2 Design / Technical data /5 Type EBWN /5 Selection and ordering data /6 Type EBWT /6 Selection and ordering
More informationProduct overview. Joints. Circlips for ball seats DIN K0714. Quick plug couplings with radial offset compensation K0709. Page 837.
Joints 825 Product overview Joints Quick plug couplings with radial offset compensation K0709 Quick plug couplings with radial offset compensation and screw-on flange K0710 Quick plug couplings with angular
More informationseries Linear guideways CG-serie 3.3 CG series
series CG-serie 3.3 CG series 3.3.1 Properties of the linear guideways, series CG The HIWIN linear guideways of the CG series with O-arrangement of the ball tracks guarantee high torque loading capacity,
More informationPrecision Modules PSK
Precision Modules PSK 2 Bosch Rexroth AG Precision Modules PSK R999000500 (2015-12) Identification system for short product names Short product name Example:: P S K - 050 - N N - 1 System = Precision Module
More informationCylindrical roller bearings for large electric motors
Cylindrical roller bearings for large electric motors Cylindrical roller bearings are typically used in belt or gear driven medium- to largesized electric motors, where heavy radial loads prevail. These
More information12.4 Miniature Type, MSC MSD Stainless Steel Series
12.4 Miniature Type, MSC MSD Stainless Steel Series A. Construction Carriage End Cap MSC Standard Type End Seal Rail MSD Wide Type Ball Retainer Bottom Seal 45 45 B. Characteristics MSC st ows with Gothic-arch
More information506E. LM Guide Actuator General Catalog
LM Guide Actuator General Catalog A LM Guide Actuator General Catalog A Product Descriptions 506E Caged Ball LM Guide Actuator Model SKR.. A2-4 Structure and Features... A2-4 Caged Ball Technology... A2-6
More informationAssortment 2013_FPT BOOK.indb /02/13 6:57 PM
Assortment Contents Why compete against your supplier when you can be our partner Chain Tensioners...14 see Chains section for details Anti-Vibration Mounts...224 Key Steel...225 Motor Rails...226 Self
More informationInner block. Grease nipple. Fig.1 Structure of LM Guide Actuator Model KR
LM Guide ctuator Model LM Guide + all Screw = Integral-structure ctuator Stopper Housing all screw Inner block Grease nipple Outer rail earing (supported side) Housing Stopper Double-row ball circuit earing
More informationQ&A Session for Advanced Linear Bearings and Guides 201 : Troubleshooting for Design Engineers
Q&A Session for Advanced Linear Bearings and Guides 201 : Troubleshooting for Design Engineers Date: April 22, 2009 Q: We are currently looking into using Self Lubricating Bushings in a high-load Off-
More informationThe Block Structure. Linear block SBG, SBS, SPG and SPS types are available. All blocks are dimensionally interchangeable.
Circular arc groove Two pint contact structure of circular arc groove. It keeps the function of self-aligning and smooth rolling performance. 45 angle of contact Four rows of circular arc groove contact
More informationFor advanced drive technology CLAMPEX. Shaft-hub-connection. KTR Precision joints CLAMPEX
technology CLAMPEX Shaft-hub-connection CLAMPEX KTR Precision joints 227 technology Table of contents Page Brief information 228 Selection and calculation 25-255 CLAMPEX -Selection Shaft diameter = d 0
More information...components in motion. Miniature Linear Guideways
...components in motion Miniature Linear Introduction Miniature linear guideway systems are widely used throughout industry for precise, compact applications. Precise and Stainless The gothic arch shape
More informationDouble-acting, magnetic, guided ø 10x2, 16x2, 20x2, 25x2, 32x2 mm
CATALOGUE > Release 8.8 > Series QX twin rod cylinders Series QX twin cylinders Double-acting, magnetic, guided ø 0x2, 6x2, 20x2, 25x2, 32x2 mm High force Precise movement Integrated guide QXB: linear
More informationChapter B-3. Chapter 3. Actuators and output devices. Festo Didactic TP101
155 Chapter 3 Actuators and output devices Festo Didactic TP101 156 An actuator is an output device for the conversion of supply energy into useful work. The output signal is controlled by the control
More informationCaged Ball LM Guide Actuator SKR
Caged Ball LM Guide Actuator SKR For details, visit THK at www.thk.com Product information is updated regularly on the THK website. CATALOG No.309-11E Integrated LM Guide and Ball Screw High-rigidity /
More informationSKF Disc Couplings. Selection
SK Disc Couplings The SK disc coupling is the ideal solution in medium to high applications that require torsional rigidity, offer some allowance for misalignment, and do not require lubrication. These
More informationHydraulic cylinders type CN - round heads with counterflanges to ISO nominal pressure 16 MPa (160 bar) - max 25 MPa (250 bar)
www.atos.com Table B80-/E Hydraulic cylinders type CN - round heads with counterflanges to ISO 600- - nominal pressure 6 MPa (60 bar) - max MPa (0 bar) SWC Cylinders Designer Software for assisted selection
More informationR310EN 2302 ( ) The Drive & Control Company
R31EN 232 (26.4) The Drive & Control Company Bosch Rexroth AG Linear Motion and Assembly Technologies Ball Rail Systems Linear Bushings and Shafts Ball Screw Drives Linear Motion Systems Basic Mechanical
More informationHunger DFE GmbH Tandem Seal. Hunger DFE Tandem Seal
Hunger DFE GmbH Tandem Seal Hunger DFE Tandem Seal Hunger DFE Tandem Seals were particularly designed for application as rod and piston seals. Two types of this product range shall be presented at this
More informationLinear Bushings and Shafts
Linear Bushings and Shafts 45 b 1cr RA 83 100.1 Linear Motion and Assembly Technologies STAR Linear Motion Technology Ball Rail Systems Standard Ball Rail Systems Ball Rail Systems with Aluminum Runner
More informationCOUPLERS 5. Fax: +44 (0)
COUPLERS Fax: +44 (0)1992 09890 3 COMPOSITE JAW COUPLERS (SERIES FS) L1 2.0 mm Max L2 2.0 mm Max L3 Bore B s 032-037 s 02-08 max features Low mass Freedom from corrosion Good damping properties Low cost
More informationSINGLE ACTING METRIC RANGE
CONTENTS Page 2 General specifications Ram Style No. Female Rod Male Rod Pin Hole 3 Part Numbering System 4 Dimensions 5 Buckling Calculations 6 Buckling Force/ Graphs 7 Load Calculations 8 PBV Flow Chart
More informationP-Quip Product Manual
1 Patent protected. P-Quip Product Manual 71000050 Revision date: January 30, 2013 Type Approved Marked Email technical@pquip.com Web page - http://www.f-e-t.com/ Instructions for the Safe Use of P-Quip
More informationHSR(Ct Grade) Cost effective Type (Ct Grade) of LM Guide Debuts STOCK DISPONIBLE ENTREGA INMEDIATA
Cost effective Type (Ct Grade) of L Guide Debuts A cost effective series of the well-established model HSR has been newly added. Optimal for the general linear guide market such as for conveyance systems!
More informationMS25 HYDRAULIC MOTORS T E C H N I C A L C A T A L O G
MS25 HYRAULIC MOTORS T E C H N I C A L C A T A L O G Modular hydraulic motors MS25 OCLAIN HYRAULICS CHARACTERISTICS Motor inertia 0.4 kg.m² Theoretical torque Max.power Max. speed Max. pressure Cams with
More informationThe Classification Chart of PMI Linear Guideways
1 The Characteristics of MI s The Classification Chart of MI s 2 (1) igh positioning accuracy, high repeatability The MI linear guideway is a design of rolling motion with a low friction coefficient, and
More informationComparison Chart. extremely difficult. Finally, separated components can rarely be re-used.
JAN 2014 Traditional Connections Why Go Keyless Keyed Bushing Systems Both QD and Taper-Lock bushing and weld-on hub systems are popular component mounting technologies. Yet both are ultimately keyed connections
More informationCLAMPEX KTR 400 Operating/Assembly instructions
1 of 10 The CLAMPEX clamping set is a frictionally engaged, detachable shaft-to-shaft connection for cylindrical shafts and bores without feather key. Table of contents 1 Technical data 2 2 Advice 2.1
More informationKLM. Application example. Linear modules Pneumatic Stroke module. 1 Single base support, SOE Adapter plate, APL 121
KLM www.comoso.com Sizes 25.. 100 Mass 0.5 kg.. 5.18 kg Driving force 50 N.. 294 N Stroke 25 mm.. 225 mm Repeat accuracy ± 0.01 mm.. ± 0.015 mm Application example 4 5 3 3 6 7 2 2 8 1 1 Pneumatic two-axis
More informationTRACK GUIDANCE SYSTEMS
EURO-BEARINGS LTD TRACK GUIDANCE SYSTEMS www.euro-bearings.com Tel. 01908 511733 email: sales@euro-bearings.com INTRODUCTION EURO-BEARINGS LTD www.euro-bearings.com Tel. 01908 511733 This linear guidance
More information2 THRUSTER WHEEL CHOCKS
2 INTERNATIONAL PATENTS APPLY 1.0 Wheel Chock Models TWCS-100-0380-0710-LH TWCS-100-0380-0710-RH TWCS-100-0711-1040-LH TWCS-100-0711-1040-RH 2 2.0 Principles of Operation International patents apply RELEASED
More informationFeatures of the LM Guide
Features of the Functions Required for Linear Guide Surface Large permissible load Highly rigid in all directions High positioning repeatability Running accuracy can be obtained easily High accuracy can
More informationFeatures of the LM Guide
Features of the Functions Required for Linear Guide Surface Large permissible load Highly rigid in all directions High positioning repeatability Running accuracy can be obtained easily High accuracy can
More informationKaydon white paper The thin section bearing of today
The thin section bearing of today by Joe Zagar, engineering specialist an SKF Group brand Thin section bearings provide space, save weight The ubiquitous ball bearing was a workhorse of industry throughout
More informationLoPro aluminium based slide system
LoPro aluminium based slide system Introducing the Hepco LoPro Hepco LoPro has been introduced to provide the designer with a lightweight yet rugged linear slide system. LoPro is aluminiumbased with steel
More informationROTARY MODULES. Rotary modules
Rotary modules Rotary modules ROTARY MODULES Series Size Page Rotary modules RM swivel unit 156 RM 08 160 RM 10 162 RM 12 164 RM 15 168 RM 21 172 RM rotor 176 RM 50 180 RM 110 182 RM 200 184 RM 310 186
More informationProduct overview. 10 Bosch Rexroth Corporation Compact Modules R310A 2602 ( ) Compact Modules CKK. Compact Modules with ball screw drive (CKK)
10 Bosch Rexroth Corporation R310A 2602 (2008.09) CKK with ball screw drive (CKK) Product overview are precision, ready-to-install linear motion systems characterized by their high performance and compact
More informationZurcon U-Cup RU /*"-8#+-8 " (&*$8 " %*+(+$4
Zurcon U-Cup RU9 Your Partner for Sealing Technology Trelleborg Sealing Solutions is a major international sealing force, uniquely placed to offer dedicated design and development from our market-leading
More informationGrooved gaskets. Types of gaskets
Types of gaskets have proven extremely useful in all areas of industry, including the most demanding sealing tasks. Our grooved gaskets can be found in conventional power plants as well as in the primary
More informationZurcon U-Cup RU2. Single Acting U-Cup Asymmetric, Double Lip, Compact Material: Zurcon
Single Acting U-Cup Asymmetric, Double Lip, Compact Material: Zurcon 121 122 U-Cup RU2 Description Today U-Cups are used primarily as seals for piston rods in hydraulic cylinders. U-Cups in polyurethane
More information