A-dec 200 P RE-INSTALLATION GUIDE

Transcription

1 A-dec 200 P RE-INSTALLATION GUIDE This document contains technical specifications for installing the A-dec 200 equipment line. Contents Structural Requirements Utility Requirements Shipping Weights Documentation References Views and Dimensions Plumbing Plan and Elevation Views A-dec 200 Chair with Support Center; Plan View A-dec 200 Chair; Elevation A-dec 200 Delivery System; Plan View A-dec 200 Delivery System; Plan View with Elevation A-dec 200 Chair with Support Center, Cuspidor, and Assistant s Instrumentation; Plan View A-dec 200 Dental Light; Plan View A-dec 200 Dental Light; Plan View with Elevation Regulatory Information Rev B

2 Structural Requirements Dental Patient Chair Interface Requirement The dental chair requires a solid, level mounting surface that meets these minimum specifications: Weight of 1000 lbs. (4450 N) for chair, dental light, delivery system, and patient. Capability to anchor chair to the floor, with a minimum pullout load of 100 lbs. (445 N) for one anchor-bolt. Utility Requirements Air NOTE Job site construction should be completed before dental equipment installation (including finished floors, ceiling, plumbing, lighting, paint, etc.). CAUTION Local regulation requires licensed plumbers and electricians to install utilities. All plumbing and utilities must conform to prevailing local codes. CAUTION The manner and method for accessing utilities within the wall is the responsibility of the design team working on the project (dental dealer, architectural services, and contractors). Utilities must be accessible without the use of tools. 1/2" (13 mm) nominal pipe compression fitting protruding 2" (51 mm) from finished floor or wall, supplied by contractor. Right angle manual shut-off valve supplied by the dental dealer and installed by contractor. Air pressure and flow of psi ( kpa), 2.5 SCFM (71 L/min) during normal use; 7.5 SCFM (210 L/min) peak intermittent flow. Air plumbing to be flushed clean before final connection to dental equipment. Water 1/2" (13 mm) nominal pipe compression fitting protruding 2" (51 mm) from finished floor or wall, supplied by contractor. Right angle manual shut-off valve supplied by the dental dealer and installed by contractor. Water pressure and flow of 60 ± 20 psi (410 ± 140 kpa), 1.5 gpm (5.7 l/min), not to exceed 40 C (104 F). Water plumbing to be flushed clean before final connection to dental equipment. Central Vacuum Central vacuum supplier must specify plumbing up to floor box utility center and its termination point in the utility center. Wet systems: NOTE The delivery system comes with a selfcontained water bottle. Municipal water is required for the cuspidor. Plumbing to terminate with 5/8" (16 mm) outer diameter (O.D.) tube protruding 1" (25.4 mm) perpendicular to the floor. 10 ± 2 inhg, 9 SCFM minimum (254 ± 51 torr, 255 L/min minimum) Gravity Drain NOTE Gravity drains are needed only on systems with a cuspidor. 1-1/2" (38 mm) nominal pipe protruding 1" (25 mm) from finished floor. Trap to be placed in line, conforming to local codes, contractor-supplied. Floor mount only. Not recommended for wall mount utilities. Measurement Acronyms Acronym N psi KPa SCFM L/min SLM inhg/torr Definition newton pounds per square inch standard liters per minute standard cubic feet per minute liters per minute standard liters per minute inches/mm of mercury (pressure) Rev B

3 Electrical 1/2" (13 mm) conduit and box with a hospital-grade power receptacle supplied by the contractor. Wire box to conform to local codes. Top of the receptacle should not be higher than 5" (127 mm) above finished floor for fit within floor box. See the following table for voltage and amperage ratings: Chair Type Required Electrical Supply Amperage Rating Amperage Breakdown 240 Volt Chair VAC, Hz, 10 Amps minimum 100 Volt Chair 100 VAC, Hz 15 Amps min (20 Amps recommended) 120 Volt Chair VAC, Hz 15 Amps min (20 Amps recommended) 10 Amps max Hz: 2 Amps chair pump motor 1.4 Amps 300-watt power supply 2 Amps ancillary products 10 Amps max Hz: 3.5 Amps chair pump motor 3.1 Amps 300-watt power supply 2 Amps ancillary products 10 Amps max Hz: 3.5 Amps chair pump motor 2.8 Amps 300-watt power supply 2 Amps ancillary products Rev B 3

4 Shipping Weights Documentation References Product/Box A-dec 200 Chair A-dec 200 Delivery System A-dec 200 Support Center A-dec 200 Dental Light Est. Shipping Weight 337 lb. (153 kg) 53 lb. (34 kg) 66 lb. (30 kg) 24 lb. (11 kg) Installation Guides: A-dec 200 Installation Guide... p/n Service Guides: A-dec 200 Service Guide p/n Instructions for Use: A-dec 200 Instructions For Use.. p/n A-dec Equip. Asepsis Guide.... p/n Regulatory and Specifications.. p/n Full-Size Templates: NOTE Use only full-scale templates for locating plumbing and electrical. A-dec 200 Full Line Product.... p/n Rev B

5 Views and Dimensions NOTE The dimensional drawings in the following pages are not to scale and are for reference only. For complete accuracy, use the appropriate full-sized templates. Plumbing Plan and Elevation Views Width of floor box cover frame Rev B 5

6 A-dec 200 Chair with Support Center; Plan View " 877 mm 27" 686 mm 21" 533 mm (Between Armrest) 6" - 12" 152 mm-305 mm 67" 1702 mm " 857 mm " 854 mm 19" 485 mm 27" 686 mm Rev B

7 A-dec 200 Chair; Elevation (shown with chair-only for clarity) 7" 178 mm 4" 102 mm 57" 1448 mm 29" 737 mm " 38 mm To Top of Seat Cushion 74" 1880 mm 15" 381 mm " 114 mm 33" 838 mm (Baseplate Only) Rev B 7

8 A-dec 200 Delivery System; Plan View (shown with only system dimensions for clarity) 25" 635 mm 20" 508 mm 24" 610 mm 28" 711 mm 29" 737mm Rev B

9 A-dec 200 Delivery System; Plan View with Elevation (shown with only system dimensions for clarity) 25" 635 mm 20" 508 mm 24" 610 mm 28" 711 mm 29" 737mm 24" 610 mm Rev B 9

10 A-dec 200 Chair with Support Center, Cuspidor, and Assistant s Instrumentation; Plan View (shown only with assistant s instrumentation dimensions for clarity) 8" 203 mm 45 11" 280 mm Rev B

11 A-dec 200 Dental Light; Plan View (shown only with dental light dimensions for clarity) 34" 864 mm " 597 mm Rev B 11

12 A-dec 200 Dental Light; Plan View with Elevation (shown only with dental light dimensions for clarity) 34" 864 mm " 597 mm 27" 686 mm Rev B

13 Rev B 13

14 Regulatory Information Regulatory information is provided with A-dec equipment as mandated by agency requirements. This information is delivered in the equipment s Instructions for Use or the separate Regulatory Information and Specifications document. If you need this information, please go to the Document Library at A-dec Headquarters 2601 Crestview Drive Newberg, OR USA Tel: Within USA/Canada Tel: Outside USA/Canada Fax: / A-dec Inc. makes no warranty of any kind with regard to the content in this document including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose Rev B Copyright 2012 A-dec Inc. All rights reserved.