UNENCLOSED 90 /ADJACENT EXIT PLATFORM (NO PIT)

Transcription

1 TECHNICAL DATA/SPECIFICATIONS RATED LOAD: INPUT POWER SOURCE: DRIVE: INTERMEDIATE REDUCTION: FINAL DRIVE: MOTOR CONTROLLER: SPEED: 750 lbs maximum Volt 8 Amp 60 Hz dedicated service Volt 3 Amp 60 Hz battery charger. 1/2 hp motor, 1750 rpm, 90 VDC, continuous duty. VPL-3100B: 1/2 hp motor, 1750 rpm, 24 VDC, continuous duty. VPL-3200B: 1 hp motor, 1750 rpm, 24 VDC, continuous duty. Dual 4L style Poly-V belts and pulleys, 3.94:1 pulley reduction. VPL-3100: 1 dia. ACME screw w/bronze nut and bronze safety back up nut. VPL-3200B: 1.25" dia. ACME screw w/bronze nut and bronze safety back up nut. 24 VAC Relay control. 24 VDC Relay control. 9 feet per minute maximum. 10 feet per minute maximum PERFORMANCE STANDARDS USA FOOD & DRUG ADMINISTRATION: CLASS II, 510(K) Exempt, File No , Product Code: PCE ANSI/ASME: A Section 5 Safety Standards for Platform Lifts and Stairway Chairlifts CSA B Lifts for Persons with Physical Disabilities (Residential Application) ANSI/ASME: CSA B /ASME-A Elevator and Escalator Electrical Equipment SHEET 1 OF 5

2 BOX (VPL-3100 SERIES) F 36 7/8" BOX (VPL-3200B SERIES) 9 15/16" J K C L OF PLATFORM G H RIGHT HAND UNIT SHOWN VPL-3200B SERIES: SOLID BACKING FROM TOP OF UNIT DOWN 10" (WALL LOADING 200 LBS.) 10" D E HANDRAIL B 14 7/8" RAMP UP A 42" SIDE WALLS 34 1/2" CONTROLS 34" HAND RAIL *MIN. TO OF VPL-3175 IS 28" C MAX* TO SHEET 2 OF 5 NOTES: 1) ACCESS RAMP CAN BE MOUNTED ON EITHER SIDE OF THE PLATFORM 2) SEE ILS FOR LANDING DETAIL/ALIGNMENT

3 ANCHOR POINT LOCATIONS/SLAB DETAIL TECHNICAL SPECIFICATIONS ATTACHMENT: VPL MUST BE FASTENED TO CONCRETE SLAB USING FOUR (4) 1/2" (3/8" BOLT) X MINIMUM 2-1/2" LONG CONCRETE ANCHORS SUITABLE FOR THE ENVIRONMENT. FOLLOW SELECTED CONCRETE ANCHOR MANUFACTURERS GUIDELINES AND APPLICABLE CODES. REQUIREMENTS: 4" THICK 3500 PSI MINIMUM COMPRESSIVE STRENGTH, REINFORCED CONCRETE SLAB. N MIN SLAB M 24 5/16" 4 1/8" 39 7/8" P MIN SLAB 3/8"-3/4" L 33 3/16" 9/16" DIA. HOLE (4) PLACES UNITS WITH 90 /ADJACENT EXIT PLATFORM SHEET 3 OF 5

4 BOX (VPL-3100 SERIES) F 36 7/8" BOX (VPL-3200B SERIES) 9 15/16" K L C L OF PLATFORM RIGHT SWING PLATFORM SHOWN OPEN G H J RIGHT HAND UNIT SHOWN VPL-3200B SERIES: SOLID BACKING FROM TOP OF UNIT DOWN 10" (WALL LOADING 200 LBS.) RIGHT & LEFT SWING PLATEFORM S AVAILABLE NOT SHOWN 10" D E HANDRAIL B 14 7/8" RAMP UP CLOSED A 42" SIDE WALLS 34 1/2" CONTROLS NOT SHOWN 34" HAND RAIL *MIN. TO OF VPL-3175 IS 28" C MAX* TO SHEET 4 OF 5 NOTES: 1) ACCESS RAMP & PLATFORM CAN BE MOUNTED ON EITHER SIDE OF THE PLATFORM 2) SEE ILS FOR LANDING DETAIL/ALIGNMENT

5 ANCHOR POINT LOCATIONS/SLAB DETAIL TECHNICAL SPECIFICATIONS ATTACHMENT: VPL MUST BE FASTENED TO CONCRETE SLAB USING FOUR (4) 1/2" (3/8" BOLT) X MINIMUM 2-1/2" LONG CONCRETE ANCHORS SUITABLE FOR THE ENVIRONMENT. FOLLOW SELECTED CONCRETE ANCHOR MANUFACTURERS GUIDELINES AND APPLICABLE CODES. REQUIREMENTS: 4" THICK 3500 PSI MINIMUM COMPRESSIVE STRENGTH, REINFORCED CONCRETE SLAB. P MIN SLAB N 24 5/16" 4 1/8" 39 7/8" 3/8"-3/4" RIGHT SWING OPEN Q MIN SLAB M 33 3/16" 9/16" DIA. HOLE (4) PLACES UNITS WITH 90 /ADJACENT EXIT PLATFORM WITH PLATFORM SHEET 5 OF 5