Ni - Cd THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY. THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
|
|
- Shanon Lee
- 6 years ago
- Views:
Transcription
1 50 Installation Instructions mergency Lighting quipment! IPORTNT SFURDS! WHN USIN LTRIL QUIPNT, SI SFT PRUTIONS SHOULD LWS FOOWD, INLUDIN TH FOOWIN: RD ND FOOW SFT INRUTIONS 1. To prevent high voltage from being present on red & yellow output leads prior to installation, inverter connector must be open. Do not join inverter connector until installation is complete and power is supplied to the emergency ballast. 2. This product is for use with one or two T8, T9, T10,T12 fluorescent lamps or one W (2 4 ) T5 lamp, including standard, energy saving, HO, VHO, circline, U-shaped lamps, and long compacts. It also operates one 13 42W 4-pin compact fluorescent lamp. It also operates one W Philips LD T8 InstantFit lamp: , , , , , , , , , , , , , , , ake sure all connections are in accordance with the National lectrical ode and any local regulations. 4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and inverter connector of the emergency ballast before servicing. 5. This emergency ballast is for factory or field installation in either the ballast channel or on top of the fixture. 6. This product is suitable for use in damp locations where the ambient temperature is 0º minimum, +50º maximum. Product is also suitable for installation in sealed and gasketed fixtures. Product is not suitable for heated air outlets and wet or hazardous locations. 7. n unswitched power source is required (120 through 277 V, 50 or 60 Hz). 8. Do not install near gas or electric heaters. 9. Do not attempt to service the battery. sealed, no-maintenance battery is used that is not field replaceable. ontact the manufacturer for information on service. 10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 11. Do not use this product for other than intended use. 12. Servicing should be performed by qualified service personnel. 13. quipment should be mounted in locations and at heights where it will not be subjected to tampering by unauthorized personnel. UTION: Verify that all replacement lamp types marked on the installed luminaire are also identified as suitable for use with this inverter/charger pack. SV THS INRUTIONS Ni - d THIS PRODUT ONTINS RHRL NIKL-DIU TTR. TH TTR U RLD OR DISPOSD OF PROPRL. 08/26/15 Philips mergency Lighting 236 t. Pleasant Rd. ollierville, TN US Tech Support Fax
2 INTION WRNIN: TO PRVNT HIH VOLT FRO IN PRSNT ON & OUTPUT LDS PRIOR TO INTION, INVRTR ONNTOR U OPN. DO NOT JOIN INVRTR ONNTOR UNTIL INTION IS OPLT ND POWR IS SUPPLID TO TH RN. P #1 NOT: ake sure the necessary branch circuit wiring is available. n unswitched source of power is required. The emergency ballast must be fed from the same branch circuit as the ballast. ININ TH RN > Disconnect power from the fixture. Remove the ballast channel cover and install the emergency ballast either in the ballast channel or on top of the fixture.* Remote mounting distance must be less than half the maximum remote mounting distance for the ballast. onsult ballast manufacturer before remote installation. > Depending on the type of fixture in use install emergency ballast using one of the methods illustrated below. > ounting Height: This product meets or exceeds the NFP minimum light requirements with all loads, down to the smallest rated lamp load, at heights up to 7.17ft (2.2m). any factors influence emergency illumination levels, such as the lamp load selected, luminare design, and environmental factors therefore end use verification is necessary. For field installations, when the attached luminaire is mounted at heights greater than 7.17ft (2.2m), the level of illumination must be measured in the end application to ensure the requirements of NFP 101 and local codes are satisfied. INSID Inside allast hannel HNNL INSID Inside RIP Strip Fixture FIXTUR ON On TOP Top OF of Fixture FIXTUR * For installation on top of the fixture, wire bundle covers (R-60) may be required by state or local codes. These covers are available from the manufacturer as an accessory kit and must be ordered separately. all your local distributor or the factory for complete information. P #2a ININ TH 2W-ITS ON FIXTUR SURF > Drill a 1/2" hole and install the test switch as shown. > Wire the test switch per wiring diagrams provided on these instructions. > If wired correctly, the 2W-ITS indicator light should be ON when power is supplied to the fixture, indicating that the emergency ballast battery is charging. fter installing, mark with the "PUSH TO T" and "HRIN INDITOR LIHT" labels. Hex Nut Drill or Punch a 1/2 Hole Fixture or Test/onitor Plate Violet rown 2 Wire Illuminated Test Switch P #2b ININ TH 2W-ITS ON TH HNNL OVR > Drill or punch a 7/8 inch hole in ballast channel cover and insert bushing. > Slide the 2W-ITS tube up or down to adjust the height and visibility of the charging indicator light. > If the tube is too long, cut the plastic tubing to necessary length. > fter cutting the tube to the proper length, assemble the 2W-ITS. To assemble the 2W-ITS: > Feed the switch leads through the plastic tubing. > Insert the white bushing in the opposite end of tube from the switch body. > Pull switch leads and use provided tie wrap to secure leads snug against white bushing. > Unscrew hex nut to apply tension to leads. Plastic Tube Tie Wrap White ushing PUSH TO T 2 Wire Illuminated Test Switch NOT: fter installing the test switch, 2 mark with the appropriate label. 2 PUSH TO T
3 INTION P #3 WIRIN TH RN > Determine the type of ballast installed in the fixture. > Select the appropriate wiring diagram on back to connect the emergency ballast to the ballast and lamp(s). ake sure all connections are in accordance with the National lectrical ode and any local regulations. > fter installation is complete, supply power to the emergency ballast and join the inverter connector. > t this point, power should be connected to both the ballast and the emergency ballast, and the harging Indicator Light should illuminate indicating the battery is charging. > short-term discharge test may be conducted after the emergency ballast has been charging for one hour. harge for 24 hours before conducting a long-term discharge test. Refer to OPRTION. OPRTION > In a readily visible location, attach the label "UTION - This Unit Has ore Than One Power onnection Point. To Reduce The Risk Of lectric Shock, Disconnect oth The ranch ircuit-reakers Or Fuses nd mergency Power Supplies efore Servicing." During normal operation power is applied, the charging indicator light is illuminated, indicating that the battery is being charged. When power fails, the ballast automatically switches to emergency power (internal battery), operating either one or two lamps for a minimum of 90 minutes. When power is restored, the emergency ballast returns to the charging mode and delays ballast operation for three seconds to prevent false-tripping of ballast (end-of-lamp-life) shutdown circuits. INTNN lthough no routine maintenance is required to keep the emergency ballast functional, it should be checked periodically to ensure that it is working. The following schedule is recommended: 1. Visually inspect the charging indicator light monthly. It should be illuminated. 2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. One or two lamps should operate at reduced illumination. 3. onduct a 90-minute discharge test once a year. One or two lamps should operate at reduced illumination for at least 90 minutes. WIRIN DIRS! RFR N SRVIIN INDITD THS HKS TO QULIFID PRSONNL! The following diagrams are typical schematics only. ay be used with other ballasts. onsult the factory for other wiring diagrams. mergency allast and allast must be fed from the S RNH IRUIT. IPORTNT TXT: RFR TO TL 1 RRDIN ND ONNTOR Table 1 ONNTOR OPN ONNTOR OPN ONNTOR LOSD JUPR WIR ONNTOR LOSD JUPR WIR LP (DITR) (1, 1¼, 1½ ) T8,T9,T10,T12 LON OPT S TP Single or ipin 4-PIN (211) TWIN/QUD/TRIPL 4-PIN TWIN-TU (24q, x24q) OPT T5 & T5 HO INITUR IPIN WTT (Length) W (2'-4') W (5' -8') NO. of LPS (RN) ONNTOR ONNTOR 1 LOSD OPN 2 OPN LOSD 1 OPN LOSD W 1 LOSD OPN W 1 LOSD OPN W 1 LOSD OPN W (2'-4') 1 LOSD OPN HO IRLIN W 1 LOSD OPN 2D 4-PIN (R10q) W 1 LOSD OPN Philips LD T8 InstantFit ipin W 1 LOSD OPN The supplied brown jumper wire can be used to connect either the brown wires or the violet wires. 3
4 FI RN ND U FD FRO TH S RNH IRUIT TPIL SHTIS ONL. USD WITH OTHR S. ONSULT TH FTOR FOR OTHR WIRIN DIRS. WIRIN DIR for 1-LP emergency operation ON (1) LP RPID RT W SWITH INVRTR ONNTOR OON (+) (-) LK R N L/LK LK 1 LP RPID RT LP FI ON (1) LP INNT RT W SWITH INVRTR ONNTOR OON (+) (-) LK R N L/LK LK 1 LP INNT RT LP FI TWO (2) LP RPID RT FI D TWO (2) LP INNT RT W SWITH INVRTR ONNTOR OON (+) (-) LK R N L/LK LK 2 LP RPID RT LP 1 ( RN) LP 2 W SWITH INVRTR ONNTOR OON (+) (-) LK R N L/LK LK LP 1 ( RN) LP 2 2 LP INNT RT FI THR (3) LP RPID RT FI F THR (3) LP INNT RT W SWITH INVRTR ONNTOR OON (+) (-) LK R N L/LK LK 3 LP RPID RT /WHT /WHT LP 1 ( RN) LP 2 LP 3 W SWITH INVRTR ONNTOR OON (+) (-) LK R N L/LK LK 3 LP INNT RT LP 1 ( RN) LP 2 LP 3 FI FOUR (4) LP RPID RT FI H FOUR (4) LP INNT RT W SWITH INVRTR ONNTOR OON (+) (-) LK R N L/LK LK 4 LP RPID RT /WHT /WHT LP 1 ( RN) LP 2 LP 3 LP 4 W SWITH INVRTR ONNTOR OON (+) (-) LK R N L/LK LK 4 LP INNT RT LP 1 ( RN) LP 2 LP 3 LP 4 FI I ON (1) LP OPT RPID RT INVRTR ONNTOR (+) (-) R N L/LK LP OON LK 1 LP RPID RT LK FI J TWO (2) LP RPID RT P DIIN OON INVRTR ONNTOR S1 S2 (+) (-) LK R N L/LK LK LK 2 LP RPID RT DIIN LP 1 ( RN) LP 2 4
5 (P) (P) (P) (P) WIRIN DIRS FOR 2-LP RN OPRTION (2-4, W LPS ONL) Two-lamp emergency operation is not possible with all ballasts. onsult the factory for any ballast other than those shown. FI K TWO (2) LP RPID RT FI L TWO (2) LP INNT RT W SWITH INVRTR ONNTOR OON (+) (-) LK R N LP 1 L/LK LP 2 2 LP RPID RT LK W SWITH INVRTR ONNTOR OON (+) (-) LK R N L/LK LK LP 1 LP 2 2 LP INNT RT FI THR (3) LP RPID RT FI N THR (3) LP INNT RT W SWITH INVRTR ONNTOR OON (+) (-) LK R N LP 1 ( RN) L/LK LP 2 ( RN) 3 LP RPID RT LP 3 LK W SWITH INVRTR ONNTOR OON (+) (-) LK R N L/LK LK 3 LP INNT RT LP 1 LP 2 LP 3 ( RN) ( RN) FI O FOUR (4) LP RPID RT FI P FOUR (4) LP INNT RT W SWITH INVRTR ONNTOR OON (+) (-) LK R N LP 1 ( RN) L/LK LP 2 4 LP RPID RT /WHT LP 3 /WHT LK LP 4 ( RN) W SWITH INVRTR ONNTOR OON (+) (-) LK R N L/LK LK LP 1 ( RN) LP 2 ( RN) 4 LP INNT RT LP 3 LP 4 FI Q TWO (2) OPT LP RPID RT INVRTR ONNTOR (+) (-) R N L/LK LP 1 LK OON 2 LP RPID RT LK LP 2 FI R WIRIN DIRS for RN-ONL fixtures ON (1) LP WITHOUT (16W-215W) FI S TWO (2) LPS WITHOUT (17W-40W) INVRTR ONNTOR (+) (-) LK R N L/LK LP INVRTR ONNTOR (+) (-) LK R N L/LK LP 1 LP 2 OON (P) OON (P) FI T ON (1) 4-PIN OPT LP WITHOUT (16W-55W) INVRTR ONNTOR (+) (-) LK OON (P) R N L L S T L/LK (P) (P) LP 5
Ni - Cd THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY. THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
LP600U Installation Instructions UNIVRSL INPUT, SLF-TIN MRN LIHTIN QUIPMNT! IMPORTNT SFURDS! WHN USIN LTRIL QUIPMNT, BSI SFT PRUTIONS SHOULD LWS B FOOWD, INLUDIN TH FOOWIN: RD ND FOOW SFT INRUTIONS 1.
More informationB30ST ! IMPORTANT SAFEGUARDS! SAVE THESE INSTRUCTIONS. Installation Instructions SELF-TESTING EMERGENCY LIGHTING EQUIPMENT
B30 Installation Instructions SLF-TIN MRN LIHTIN QUIPMNT WHN USIN LTRIAL QUIPMNT, BASI! IMPORTANT SAFUARDS! SAFT PRAUTIONS SHOULD ALWAS B FOOWD, INLUDIN TH FOOWIN: RAD AND FOOW A SAFT INRUTIONS 1. To prevent
More informationNi - Cd THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY. THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
P600STU Installation Instructions UNIVRSA INPUT, SF-ING MRGNC IGHTING QUIPMNT! IMPORTANT SAFGUARDS! WHN USING CTRICA QUIPMNT, ASIC SAFT PRCAUTIONS SHOUD AWAS FOOWD, INCUDING TH FOOWING: RAD AND FOOW A
More informationPSL600 MVOLT SD INSTALLATION INSTRUCTIONS ! IMPORTANT SAFEGUARDS!
PS600 MVOT SD INSTAATION INSTRUCTIONS! IMPORTANT SAFGUARDS! WHN USING CTRICA QUIPMNT, ASIC SAFT PRCAUTIONS SHOUD AWAS FOOWD, INCUDING TH FOOWING: RAD AND FOOW A SAFT INSTRUCTIONS 1. To prevent high voltage
More informationB33 INSTALLATION INSTRUCTIONS ! IMPORTANT SAFEGUARDS!
33 INSTAATION INSTRUCTIONS! IMPTANT SAFGUARDS! WHN USING CTRICA QUIPMNT, ASIC SAFT PRCAUTIONS SHOUD AWAS FOOWD, INCUDING TH FOOWING: RAD AND FOOW A SAFT INSTRUCTIONS 1. To prevent high voltage from being
More informationWHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING THE FOLLOWING:
SURE-LITES Installation Instructions For FBP-1-40X IMPTANT SAFEGUARDS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING THE FOLLOWING: 1. READ AND FOLLOW ALL
More informationNi - Cd THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY. THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
LD7UNVCL Installation Instructions MGNCY LD DIV CLASS 2 OUTPUT WHN USING LCTICAL QUIPMNT, BASIC! IMPOTANT SAFGUADS! SAFTY PCAUTIONS SHOULD ALWAYS B FOLLOWD, INCLUDING TH FOLLOWING: AD AND FOLLOW ALL SAFTY
More informationInstallation Instructions
When using this lighting device the safety precautions should be followed at all times. PLEASE READ CAREFULLY AND FOLLOW ALL INSTRUCTIONS F YOUR OWN SAFETY 1. This device is designed for indoor use. Do
More information3. Please ensure the electricity connections conform to the National Electrical Code and local regulations if applicable.
FLUORESCENT EMERGENCY BALLAST WARNING: When using this lighting device, safety precautions should be followed at all times. CAUTION: Verify that all replacement lamp types marked on the installed luminaire
More informationBAL3000 BAL3000. Fluorescent Emergency Ballast Lumens. Specification Sheet. Emergency Ballast 1/19/2012. Project: Catalog#: Approved by:
1/19/2012 Fluorescent 1450-3000 Lumens Works in conjunction with an AC ballast to convert new or existing fluorescent fixtures into unobtrusive emergency lighting Maintains illumination of one or two lamps
More informationUL AND CODE COMPLIANCE
BAL500 FLUORESCENT EMERGENCY BALLAST 500 Lumens APPLICATION The BAL500 fluorescent emergency ballast works in conjunction with the AC ballast to convert new or existing fluorescent fixtures into emergency
More informationKT-EMRG-1400-SL /B. 3. Please ensure the electricity connections conform to the National Electrical Code and local regulations if applicable.
FLUORESCENT EMERGENCY BALLAST WARNING: When using this lighting device, safety precautions should be followed at all times. CAUTION: Verify that all repalcment lamp types marked on the installed luminaire
More informationBAL1400 FLUORESCENT EMERGENCY BALLAST Specification-grade One or two-lamp emergency illumination
BAL1400 FLUORESCENT EMERGENCY BALLAST Specification-grade One or two-lamp emergency illumination APPLICATION The BAL1400 fluorescent emergency ballast works in conjunction with the AC ballast to convert
More informationINSTRUCTION MANUAL IMPORTANT SAFEGUARDS. When using electrical equipment, basic safety precautions should always be followed, including the following:
INSTRUCTION MANUAL IMPORTANT SAFEGUARDS SERIES D LIGHTING EQUIPMENT When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY
More informationFLUORESCENT EMERGENCY BALLAST Lumens. When using this lighting device safety precautions should be followed at all times
FLUORESCENT 400 Lumens INSTALLATION INSTRUCTIONS When using this lighting device safety precautions should be followed at all times PLEASE READ CAREFULLY AND FOLLOW ALL INSTRUCTIONS FOR YOUR OWN SAFETY.
More informationBAL3000 FLUORESCENT EMERGENCY BALLAST Specification-grade: Up to 3500 lumens One or two-lamp emergency illumination
BAL3000 FLUORESCENT EMERGENCY BALLAST Specification-grade: Up to 3500 lumens One or two-lamp emergency illumination APPLICATION The BAL3000 fluorescent emergency ballast works in conjunction with an AC
More informationInstallation and Operation Instructions 10/04/13
ELI-S-100 With DIMMING CAPABILITIES Installation and Operation Instructions eli series emergency lighting inverters NRTL/C! IMPORTANT SAFEGUARDS! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS
More informationSURE-LITES FBP140XLP Instruction Manual
SURELITES Instruction Manual IMPORTANT SAFEGUARDS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE OBSERVED INCLUDING THE FOLLOWING: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. CAUTION:
More informationINSTRUCTION MANUAL. IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following:
SERIES E Emergency Lighting Equipment IMPTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
More informationBALT5-800 LOW-PROFILE FLUORESCENT EMERGENCY BALLAST
BALT5-800 LOW-PROFILE FLUORESCENT EMERGENCY BALLAST APPLICATION The BALT5-800 low-profile fluorescent emergency ballast works in conjunction with the AC ballast to convert new or existing fluorescent fixtures
More informationUFO-RP2 FLUORESCENT BATTERY PACK IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
FLUORESCENT BATTERY PACK IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. - To
More informationUFO-RP3 FLUORESCENT BATTERY PACK IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
FLUORESCENT BATTERY PACK IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS. - To
More informationMorris Products 53 Carey Road, Queensbury, NY 12804
Catalog Number 790 UPC Number 60986790 Description Low Profile Emergency Lighting allast 500 Lumen T5 & T8 Fixtures Features For both normal and emergency Flourescent lighting. In the event of a Power
More informationINSTRUCTION MANUAL IMPORTANT SAFEGUARDS. When using electrical equipment, basic safety precautions should always be followed, including the following:
INSTRUCTION MANUAL IMPORTANT SAFEGUARDS SERIES D LIGHTING EQUIPMENT When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY
More informationInstallation And Operation Instructions For FHSCP-UNV Series Emergency LED Drivers Models: FHSCP-UNV-5WL, 7.8WL, 10.7WL, 13.
Installation And Operation Instructions For FHSCP-UNV Series Emergency LED Drivers Models: FHSCP-UNV-5WL, 7.8WL, 10.7WL, 13.7WL, 17WL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety
More informationINSTRUCTION MANUAL. IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following:
IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. CAUTION To prevent electrical
More informationSAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS EMERGENCY FLUORESCENT BATTERY PACK MODEL PS300, PSQ500, PS600, PS1400 CAUTION: For safety and proper operation, read and follow instructions carefully before installation. FIELD
More informationEEQ SERIES COMPACT FLUORESCENT EMERGENCY FACTORY SEALED LIGHTING FIXTURES
INSTALLATION, OPERATION & MAINTENANCE DATA SHEET (EEQ SERIES COMPACT FLUORESCENT EMERGENCY FACTORY SEALED LIGHTING FIXTURES) EEQ SERIES COMPACT FLUORESCENT EMERGENCY FACTORY SEALED LIGHTING FIXTURES CAUTION:
More informationInstallation Instruction
T F W 604.549.9379 604.549.9555 fluxwerx.com Installation Instruction DRIVER ENCLOSURE Ceiling Type Version Grid Battery Pack GRID MOUNT INSTALL OPTIONS OPTION 1: Standard Vertical Grid drivers can be
More informationIMPORTANT SAFEGUARDS
INSTRUCTION MANUAL NON-INTERRUPTIBLE AC INVERTER SYSTEM MODEL EAC FTM 350 FOR EMERGENCY LIGHTING POWER IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed,
More informationHIGHBAY RAIL 400W INSTALLATION INSTRUCTIONS
TM INSTALLATION INSTRUCTIONS IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Fixtures must be wired in accordance with the National Electrical Code and
More informationSAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
Champ Fluorescent Luminaires DMVFB Auxiliary Series - 52, 64, & 84 Watt Installation & Maintenance Information SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE IF 1713 IMPORTANT SAFEGUARDS READ AND FOLLOW
More informationStrip Fixture URS Light Bar Retrofit Installation Instructions Revised:
Strip Fixture URS Light Bar Retrofit Installation Instructions Revised: 20180126 These instructions do not purport to cover all details or variations in components nor to provide for every possible contingency
More informationUniversal Retrofit System Installation Instructions Revised:
Universal Retrofit System Installation Instructions Revised: 20150624 These instructions do not purport to cover all details or variations in components nor to provide for every possible contingency to
More informationAEROBAY INSTALLATION INSTRUCTIONS
AEROBAY INSTALLATION INSTRUCTIONS AEROBAY IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Fixtures must be wired in accordance with the National Electrical
More informationSPECIFICATION SHEET :FH6-DUAL-3000L. Project Type Model # Remarks
Project Type Model # Remarks Description: Firehorse Emergency Ballast for use with or without AC ballast designed to add emergency lighting when main AC power is interrupted for minimum of 90 minutes at
More informationCat# DC LED Array Emergency Driver
Cat# 72918 DC LED Array Emergency Driver Morris DC LED Array Emergency Driver provides emergency operation of DC LED arrays during loss of AC power. In the event of AC power failure, the 72918 will operate
More informationINSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR NEW YORK 18 WATT SERIES
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR NEW YORK 18 WATT SERIES IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following:
More informationSAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be
More informationMANUFACTURED IN THE UK
The Trojan range of energy efficient bulkhead fittings are manufactured with a polycarbonate base and diffuser. Together with a poured gasket the Trojan leads vandal-resistant IP65 technology. With a hinged
More information2D products are warranted for one year, the expected life of the ballast and/or Emergency module is 5 years
2D products are warranted for one year, the expected life of the ballast and/or Emergency module is 5 years The Trojan range of energy efficient bulkhead fittings are manufactured with a polycarbonate
More informationR. STAHL Schaltgeräte GmbH Geschäftsbereich Leuchten Nordstraße Weimar, Germany
ECOLUX 6608 Series 6608/5 Explosion Protected Fluorescent Emergency Light Fixtures for Hazardous and Corrosive Applications Please read this entire document before beginning any work. 1. Safety Instructions
More informationThis Driver Will Operate Constant Current LED Arrays With a Working Voltage Between 11-56VDC And Not Exceeding 20W.
FHS2-UNV-56S SPECIFICATION SHEET: This Is An Original Product From Fulham Co., Inc Description: Emergency LED Driver For Back-up Lighting. This Driver Will Operate Constant Current LED Arrays With a Working
More informationSure-Lites. Installation Instructions for the Sure-Lites UX Self Powered Exit Sign with Self Diagnostics. IB505037EN Important Safeguards
049-289 Sure-Lites Installation Instructions for the Sure-Lites UX Self Powered Exit Sign with Self Diagnostics. WARNING Risk of Fire/Electric Shock If not qualified, consult an electrician. WARNING Risk
More informationR. STAHL Schaltgeräte GmbH Geschäftsbereich Leuchten Nordstraße Weimar, Germany
, INC. ECOLUX 6600 Series 6600/5 Explosion Protected Fluorescent Light Fixtures for Hazardous and Corrosive Applications Please read this entire document before beginning any work. 1. Safety Instructions
More informationInstallation Documentation ID-2663
Installation Documentation ID-2663 FLEXXA LP INDIRECT, SEMI-INDIRECT SYSTEMS Ergoline Modular Instructions included with this package: Document 266-pend 266-end 266-joint General Description Flexxa LP
More informationSAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION IMPORTANT SAFEGUARDS! When using electrical equipment, basic safety precautions should always be
More informationLED 2/3/4ft T8 Tube 120V
E-T8-1200-YR LED 2/3/4ft T8 Tube 120 Our LED Tubes utilize the latest LED chips as the light source, whilst using the standard T8 end caps, which makes it easy to install and replace traditional fluorescent
More informationLED W IMPORTANT: not provide. contact the. fire. LED only. entrap heat. applications. carry high GENERAL: Compare. material.
2016 Philips Lighting Holding B.V. All rights reserved. AEROSCAPE LED W WALL SCONCE IMPORTANT: Read carefully before installing. All work should be performed by a qualified Electrician. These instructions
More informationMaxLite LED UTILITY WRAP FIXTURES
General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions
More informationAssembly Instructions Retrofitting
Assembly Instructions Retrofitting These instructions are for replacing existing lighting fixtures or systems with our new, higher efficiency TLS, drivers and controls. www.tls-lumisign.com 514-858-6556
More informationSPECIFICATION SHEET : FHS2-UNV-36L
SPECIFICATION SHEET : FHS2-UNV-36L This Is An Original Product From Fulham Co., Inc Description : Emergency LED Driver For Back-up Lighting This driver will operate constant current LED arrays with a working
More informationDoc Ref: WD024/2/11/12 Fern-Howard Ltd. 2 Newman Lane, Alton, Hampshire, GU34 2QR. Reg. No
The Galileo II range of decorative, wall or ceiling mounted luminaires, are as versatile as they are attractive. The range is available in two body sizes, 350mm and 425mm diameter, and in a variety of
More informationBulletin 1494V Variable Depth, Flange Operated Circuit Breaker Kits for 125A, 150A 250A and 400A Frame Sizes
ulletin 494V Variable epth, Flange Operated ircuit reaker Kits for 5A, 50A 50A and 400A Frame Sizes ATTENTION: To prevent electrical shock, disconnect from power source before installing or servicing.
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS!
IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS. When using electrical equipment, basic safety precautions should always be followed including the following: DISCONNECT AC POWER SUPPLY BEFORE
More informationIMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following:
ZR-RK Series LED Retrofit Troffer Kit Includes: ZR22RK and ZR24RK Standard and Emergency Luminaires IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed
More informationSelf-Testing Industrial Series
Series: AS-I (Maint.-Free) Self-Testing Industrial Series Emergency Lighting Equipment Instructions for INSTALLATION OPERATION SERVICE SPECIFICATIONS 1300650 1300654 1300666 1300754 1300823 1300886 Hubbell
More informationSTOP BEFORE YOU BEGIN READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY
STOP BEFORE YOU BEGIN READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY WARNING Risk of fire or electrical shock. LED retrofit installations require knowledge of luminaire electrical systems. If not qualified,
More informationMANUFACTURED IN THE UK
The Galileo II range of decorative, wall or ceiling mounted luminaires, are as versatile as they are attractive. The range is available in two body sizes, 350mm and 425mm diameter, and in a variety of
More informationIMPORTANT SAFEGUARDS READ THIS MANUAL AND FOLLOW ALL SAFETY INSTRUCTIONS THOROUGHLY BEFORE OPERATING THE EMIU INVERTER SYSTEM SAVE THESE INSTRUCTIONS
THIS UNIT CONTAINS A RECHARGEABLE VALVE-REGULATED LEAD ACID BATTERY. PLEASE RECYCLE OR DISPOSE OF PROPERLY. IMPORTANT SAFEGUARDS INTERRUPTIBLE EMERGENCY LIGHTING UNIT INVERTER INSTRUCTION MANUAL When using
More informationULTRA PERFORMANCE LED TUBE INSTALLATION INSTRUCTIONS
Ultra Performance LED Tube Installation Instructions Page 1 of 7 ULTRA PERFORMANCE LED TUBE INSTALLATION INSTRUCTIONS These instructions do not purport to cover all details or variations in components
More informationIMPORTANT SAFEGUARDS READ THIS MANUAL AND FOLLOW ALL SAFETY INSTRUCTIONS THOROUGHLY BEFORE OPERATING THE LMIU INVERTER SYSTEM SAVE THESE INSTRUCTIONS
THIS UNIT CONTAINS A RECHARGEABLE VALVE-REGULATED LEAD ACID BATTERY. PLEASE RECYCLE OR DISPOSE OF PROPERLY. IMPORTANT SAFEGUARDS INTERRUPTIBLE EMERGENCY LIGHTING UNIT INVERTER INSTRUCTION MANUAL When using
More informationEMIU 720W Mini Inverter
THIS UNIT CONTAINS A RECHARGEABLE VALVE-REGULATED LEAD ACID BATTERY. PLEASE RECYCLE OR DISPOSE OF PROPERLY. INTERRUPTIBLE EMERGENCY LIGHTING UNIT INVERTER INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION.
Installation Instructions 2RTLEDR/2RTLEDRT Relight Assembly READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION. IMPORTANT SAFETY INSTRUCTIONS WARNING:
More informationSpectron Industrial Series
1300650 1300654 1300666 1300754 1300823 1300886 Table B Constant Value per Voltage System Wire Size (Maximum Voltage Drop 5%) System 6 Volt 12 Volt 24 Volt Wire Size #12 #10 #8 #6 #12 #10 #8 #6 #10 #12
More informationLED AC DRIVERLESS FLOODLIGHTS WITH PIR FOR MODEL: FLAC10BPIR, FLAC20BPIR, FLAC30BPIR & FLAC50BPIR
INTRODUCTION The LED AC Driverless Floodlights with PIR include a hanging / mounting bracket and a 100cm cable. SPECIFICATION LED 800-4000lm IP65 180-240V IK07 6000K 50Hz >80 Ra 10W- 50W Dimensions: FLAC10BPIR:
More informationACCESSORY KIT INSTALLATION INSTRUCTIONS
ACCESSORY KIT INSTALLATION INSTRUCTIONS Low Ambient Accessory For Air Cooled Split-System Air Conditioners HA 300, HB 360 / 480 / 600, HF-25, HL-30 / -40 / -50 Models GENERAL These split-system condensing
More informationDoc Ref: WD029/2/11/12 Fern-Howard Ltd. 2 Newman Lane, Alton, Hampshire, GU34 2QR. Reg. No
Clean design lines give the Meridian range a leading edge for internal, easily maintained fittings. A straightforward design with a twist and lock diffuser means user-friendly maintenance and cost savings
More informationOperating Instructions
DuroSite & SafeSite Area Light with Adapters Important Information: These instructions contain safety information, read and follow them carefully. Dialight will not accept any responsibility for injury,
More informationACCESSORY KIT INSTALLATION INSTRUCTIONS
ACCESSORY KIT INSTALLATION INSTRUCTIONS Low Ambient Accessory For Air Cooled Split-System Air Conditioners HA300, HB360/480/600, HF-25, HL-30/-40/-50 and J25HA, J30/40/50 HB Models GENERAL These split-system
More informationInstallation Instructions Central Battery Units
Phone: 605.542.4444 concealite.com! Installation Instructions s Please Save These Instructions Important Safeguards Read and Follow All Safety Instructions When using electrical equipment, basic safety
More informationwww.greenelectricalsupply.com 1x4 2x2 & 2x4 Read all instructions and warnings before attempting installation. RISK OF FIRE OR ELECTRIC SHOCK. LED RETROFIT INSTALLATION REQUIRES KNOWLEDGE OF LUMINAIRES
More informationProduct Installation Instruction LED Tube Lamp Retrofit Kits
Regular T8 internal driver single end Product Installation Instruction LED Tube Lamp Retrofit Kits 1 General Description LED Tube Light adopts the new type LED as the light source, using the standard T8
More informationECO CFL. with Photocell. Instructions. Model: ECO2DD Model: ECO3DD
ECO1DD WITHModel: PHOTOCELL Model: ECO2DD Model: ECO3DD ECO1DD.1 ECO2DD.1 Instructions ECO3DD.1 I nn S& TORp eurca tti ni O Installatio g N I n Ss t r u c t i o n s ECO CFL ECOFlood CFL Light with Photocell
More informationELECTRONIC FLUORESCENT BALLASTS
Ordering Information How to Order Philips Lighting has developed the industry s broadest distribution system for electronic ballasts. More than 000 stocking distributors nationwide. For information on
More informationInstallation Guide. WARNINGS Read all instructions and warnings before attempting installation
Installation Guide WARNINGS Read all instructions and warnings before attempting installation ALWAYS MAKE ABSOLUTELY SURE THE POWER IS OFF WHEN PERFORMING THE FIXTURE MODIFICATION. DURING INSTALLATION,
More informationDMC-500 TM. DC Motor Drive Control. Operation / Installation Manual Manual Part Number: S8M5003 Date: August 11, Computer Weld Technology, Inc.
omputer Weld Technology, Inc. 070 Old ammel N Houston Rd. Houston, TX 77086 Telephone: (7) 46-8 Fax: (7) 46-50 DM-500 TM D Motor Drive ontrol Operation / Installation Manual Manual Part Number: S8M500
More informationDeSoto NEMA 4X EMERGENCY LIGHTING UNIT. U.S. Versions: 6V- DM90X618 / DM90X654 12V- DM90X1254 / DM90X12100 INSTALLATION INSTRUCTIONS
DeSoto U.S. Versions: 6V- DM90X618 / DM90X654 12V- DM90X1254 / DM90X12100 NEMA 4X EMERGENCY LIGHTING UNIT INSTALLATION INSTRUCTIONS U.S. Patent No.s 6,135,624; 6,193,395; 6,502,044 B1; D505,222; IMPORTANT
More informationInstallation and Operation Instructions SERVICE BY QUALIFIED PERSONNEL ONLY
ELI-S-600 120 Volt ELI SERIES EMERGENCY LIGHTING INVERTERS Installation and Operation Instructions! IMPORTANT SAFEGUARDS! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED,
More informationInstruction/Installation Manual
Instruction/Installation Manual Retrofit:LED Tube Lamp 4ft. Fluorescent T8/T10 Replacement 1 SECTION 1 - General Information Kit components:1-led Tube, 1-Label and 1-Set of Instructions Models were only
More informationSURFACE/CEILING & SUSPENDED MOUNT INSTALLATION
SURFE/CEILING & SUSPENDED MOUNT INSTALLATION E477827 E477827 APPLICATION NL luminaires are designed for use indoors, outdoors, wet locations, areas containing moisture, dirt, corrosion, vibration and rough
More informationINSTALLATION INSTRUCTION W Track Recessed 120V Flangeless
W Track Recessed 120V Flangeless WT4-RTL, WT8-RTL, WT12-RTL SAFETY INSTRUCTION Read all of these instructions before installing the track system. Turn off power at main switch before installing or modifying
More informationELECTRONIC FLUORESCENT BALLASTS
Ordering Information How to Order Philips Lighting has developed the industry s broadest distribution system for electronic ballasts. More than 3000 stocking distributors nationwide. For information on
More informationResilient-Seated Gate Valves with Vertical or Cross Wall Post Indicator
Worldwide ontacts www.tyco-fire.com Resilient-Seated Gate Valves with Vertical or ross Wall Post Indicator General Description TYO Resilient-Seated Gate Valves with Vertical and ross Wall Indicators are
More informationResilient-Seated Gate Valves with Vertical or Cross Wall Post Indicator
Worldwide ontacts www.tyco-fire.com Resilient-Seated Gate Valves with Vertical or ross Wall Post Indicator General Description TYO Resilient-Seated Gate Valves with Vertical and ross Wall Indicators are
More informationDUSK-TO-DAWN LIGHT MODEL #GU8813-BZ-I, #GU8813-WH-I
ITEM #0333554, #0333553 DUSK-TO-DWN LIGHT MODEL #GU8813-BZ-I, #GU8813-WH-I Utilitech & UT Design and Grounded in Quality are registered trademarks of LF, LL. ll Rights Reserved. Français p. 7 Español p.
More informationLED Utility Wrap Fixture
Operating Instruction Please read and save these instructions. Read through this owner s manual carefully before using product. Protect yourself and others by observing all safety information, warnings,
More informationACCESSORY KIT INSTALLATION INSTRUCTIONS
ACCESSORY KIT INSTALLATION INSTRUCTIONS Low Ambient Accessory For Air Cooled Split-System Air Conditioners YD360/480/600, YJ-30/-40/-50 and J30/40/50 YD Models 642546-UAI-A-080 GENERAL Standard operation
More informationBattery Control Center - Diesel
Service Manual CAUTION: All servicing of the Battery Control Center should be done only by a qualified Service Technician. Inadvertent shorts inside the Battery Control Center could result in severe damage
More informationWiring Diagram and Circuits, Vehicle. Specifications 400/4. Fuse/Relay/Circuit Breaker Identification, LH DR, Positions 1 through 25
54.01 Wiring iagram and ircuits, Vehicle use//ircuit reaker Identification, LH R, Positions 1 through 25 PMLayout * use//ircuit reaker Identification, LH R, Positions 1 through 25 PMLayout * 1 Hazard-Warning
More informationModel: ECO1FL Model: ECO2FL Model: ECO3FL. Installation & Operating Instructions ECO CFL Flood Light Uncontrolled
Model: ECO1FL Model: ECO2FL Model: ECO3FL Installation & Operating Instructions ECO CFL Flood Light Uncontrolled 2x 2x 20W 4 x 32mm 1 Ø6mm 60mm 35mm 6 x 30mm 2 Slaving For ECO CFL Flood Light Uncontrolled
More informationEmergency lighting units PC COMBO
T5 PC, 220 240 V 50/60 Hz Linear fluorescent lamps Product description Combination of electronic ballast and emergency lighting unit For T5 fluorescent lamps Low-profile casing (21 x 30 mm cross-section)
More informationINSTALLATION INSTRUCTIONS For Light*Waves Flex II Kit with 300-Watt remote transformer
IMPORTANT SAFETY INSTRUCTIONS READ ALL OF THESE BEFORE INSTALLING THE TRACK SYSTEM. SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS TO OR CHANGES TO THE SYSTEM ARE MADE. THIS IS A 12-VOLT SYSTEM
More informationMODELS 2 & 4 Top Conduit Linears
INSTALLATION AND MAINTENANCE MANUAL SAFESITE AND DUROSITE LED LINEAR FIXTURE Document No: 9100-127-1885-99 Rev E December, 2016 MODELS 2 & 4 Top Conduit Linears These instructions contain important safety
More informationNON MAINTAINED TWIN SPOTLIGHT WALL MOUNT LED EMERGENCY LIGHT
Model No. PEL00581 NON MAINTAINED TWIN SPOTLIGHT WALL MOUNT LED EMERGENCY LIGHT 1 Please read these instructions carefully before starting installation and retain for future reference. The centre page
More informationDeSoto EMERGENCY LIGHTING UNIT. U.S. Versions: 12V- DM (P2 & P3) / DM / DM INSTALLATION INSTRUCTIONS
DeSoto U.S. Versions: 12V- DM80212100 (P2 & P3) / DM80212150 / DM80212450 EMERGENCY LIGHTING UNIT INSTALLATION INSTRUCTIONS U.S. Patent No.s D419,097; 6,135,624; 6,193,395; 6,502,044 B1 Canadian Patent
More informationFOR USE WITH MODEL NUMBERS:
INSTALLATION AND MAINTENANCE MANUAL SAFESITE /DUROSITE HZx/ STW SERIES WITH MOUNTING ACCESSORIES Document No: 9100-127-2297-99 Rev C AUGUST 2015 FOR USE WITH MODEL NUMBERS: HZXXXXXW01 HZXXXXXW45 HZXXXXXS45
More information1,2,3... As easy as. Mark 10 Powerline. For Compact Fluorescent Lamps
s easy as 1,2,3... Mark 10 Powerline immable allasts Listed 704G Philips dvance Mark 10 Powerline immable allasts make converting your existing fixtures easy. For companies looking to make their fixed-output
More informationFHS2-UNV-36L INSTALLATION INSTRUCTIONS
Emergency LED Driver Universal Voltage: 100-277VAC, 50/60Hz Output Wattage: 1.2-20W Output Current: 700mA Max. Output voltage range of 12-55VDC This Driver Will Operate The Following LED Modules: Any LED
More informationELECTRONIC FLUORESCENT BALLASTS
ELECTRONIC FLUORESCENT LLSTS Fluorescent allasts Optanium mbistar SmartMate Standard T5HO PureVOLT 1 ELECTRONIC FLUORESCENT LLSTS Fluorescent allasts Fluorescent allasts - - Optanium High-efficiency electronic
More information