EU TF coils status. A.Bonito Oliva F4E Magnets Project Manager
|
|
- Lily Carr
- 6 years ago
- Views:
Transcription
1 EU TF coils status A.Bonito Oliva F4E Magnets Project Manager Slide 1
2 Presentation Outline TF coils Main Manufacture Steps Procurement strategy Status of the production Contracts and industries involved One of main challenges: interfaces management Slide 2
3 The TF coils: main parameters 16500mm 10 TF Coils produced in Europe 9TF coils Produced in Japan Weight : 300t/coil!
4 EU TF coils: Composed by 2 main components COIL CASES from Japan The TF coils is composed by the winding pack inside a stainless coil case. WINDING PACK: Composed by 7 Double Pancakes staked and impregnated together
5 EU TF coils: Manufacture of a double pancake (DP) RP manufacture DP Heat treatment (650 C) Winding Conductor Transfer conductor into radial plate RP grooves Conductor insulation CP laser welding Impregnation Ground insulation
6 g EU TF coils procurement split in 3 contracts Completion of 10 TF coils Manufacture of 10 Winding Packs Winding Pack s main components Coil Case from JAEA Conductor from EU,RF,CN & US Manufacture of 70 Radial Plates Radial Plate
7 Contracts for EU TF coils Manufacture of 70 Radial Plates Contract placed on December 2012 Consortium CNIM - SIMIC (50-50 production) Main sub-suppliers: 3 Portal Machines: CRENAU, INNSE-Berardi (twin PM), PAMA Forged sectors (50-50): Thyssen-Grodtiz & Forgiatura Vienna Cover plate suppliers: Calvi for cold drawing, Kersten for bending.
8 Contracts for EU TF coils Manufacture of 70 Double Pancakes and 10 Winding Packs Contract placed on July 2010 Consortium ASG-Iberdrola-Elytt Main place of production : ASG La Spezia Main tooling suppliers: Winding tooling, Insertion tooling, WP impregnation tooling: TPA Brianza Turn Insulation and DP VPI: Elytt Furnace: Terruzzi Laser welding: TTM group
9 Contracts for EU TF coils Cold test and Insertion of 10 Winding Packs Contract Placed in May 2014 Main suppliers: SIMIC BNG Main Place of production: Porto Marghera, Italy Main Tooling: Cryoplant: BNG-Messer Gap Filling: Hedrich
10 Main challenge: Interfaces between suppliers Many supplier and sub-suppliers involved High level of technical risks: never done before on this scale and very complex technology! Very complex interfaces: An example: Radial Plate and Double Pancake RP and DP are produced by 2 different suppliers In order to be able to fit the conductor inside the radial plate groove, the double spiral trajectory of the DP and of the RP groove must match perfectly (within tenths of mm) over a length of about 700m!
11 DP vs RP interface This is interface is very delicate to manage due to the combination of the demanding requirement on both suppliers and to the potential financial consequences in case one DP cannot fit the RP groove ( up to 10MEuros if we have to throw away both!) How did we manage it? 1. R&D: In order to reduce technical uncertainty F4E placed initially 2 contracts to manufacture 2 RP prototypes: finally a mix of the 2 technology was selected. This R&D also gave an indication of the achievable tolerances.
12 DP vs RP interface (II) 2. Initial Risk mitigation Initially in order to reduce risks for the industries (and for us ), we selected a conservative route where RP groove is machined only after as-built DP conductor trajectory is known. 3. Rigorous quality control In order to master the technology we introduced many intermediate quality controls which gave the capability to detect and correct issues at an early stage 4. Adaptation of strategy to learning curve Once technology reached a comfortable level we moved to parallel production of RP and DP, saving several months on the schedule. This gives benefit to ITER schedule and to the suppliers reducing waiting time.
13 So in summary our recipe has been: R&D to select best technology Initial conservative approach to minimize initial risks Rigorous intermediate quality to master better technology Flexibility to adapt manufacturing strategy to learning curve Did we succeed in mastering this interface?
14 TF coils Series Production Status Process No. units completed Notes Radial Plates fabrication Double Pancakes Winding 14 (2 TF coils) 25 (more than 3 TF Coils!) Production rate: 1 every 13 days Production rate >1/2 weeks DP Heat Treatment 15 HT cycle ~1 month DP Transfer & Insertion 11 Process time ~1 week DP Conductor Insulation DP Cover Plate Laser Welding 8 Process time ~3-4 weeks 4
15 Successfully completion superconducting full size Prototype Double Pancake! The first-ever Double Pancake prototype has been successfully completed and passed all acceptance tests! 15
16 Thanks Slide 16
ITER Magnets Update European perspective
ITER Magnets Update European perspective Hannu Rajainmaki, Boris Bellesia, Alessandro Bonito-Oliva, Eva Boter, Thierry Boutboul, Eugen Bratu, Marc Cornelis, John Fanthome, Robert Harrison, Peter Readman,
More informationPF Coil 2-6 Supply. Main technical aspects. P. Valente
PF Coil 2-6 Supply Main technical aspects P. Valente PF Coils EI Information Meeting Cadarache, 19 February 2013 This presentation is intended for reference purposes only and is not a legally binding document
More informationPF Coil Fabrication Overview
PF Coil Fabrication Overview PF Coils Information Meeting Barcelona - 15 th October 2012 This presentation is intended for reference purposes only and is not a legally binding document PF Building Layout
More informationProgress of the JT-60SA Project
Progress of the JT-60SA Project P. Barabaschi, Y. Kamada, H. Shirai For the JT-60SA Integrated Project Team EU: F4E-CEA-ENEA-CNR/RFX-KIT-CIEMAT-SCKCEN JA: QST C.R.FRASCATI- ITALY 1 JT-60SA Project Agreement
More informationTorus Coil. Construction and Geometry for Modeling. D. Kashy CLAS12 Collaboration Meeting March 6, 2018
Torus Coil Construction and Geometry for Modeling D. Kashy CLAS12 Collaboration Meeting March 6, 2018 Introduction We all know in general what the CLAS12 Torus is In this talk I will attempt to explain
More informationJT-60SA Newsletter. Cryoplant arrives at the JAEA Naka Site. No. 65, 31 May Headline
JT-60SA Newsletter Headline Cryoplant arrives at the JAEA Naka Site No. 65, 31 May 2015 After the successful discharge at the port of Hitachi on 21 March 2015, the refrigerator cold box (RCB) and the auxiliary
More informationBarcelona, 26/06/2018
Barcelona, 26/06/2018 F4E_D_2CEBYC Subject: In accordance with the provisions defined in Article 124 of the Commission Delegated Regulation (EU) No 1268/2012 1, the table below summarizes modifications
More informationGENERAL ATOMICS ITER CEnTRal SolEnoId ModulE FabRICaTIon September 2018
GENERAL ATOMICS ITER Central Solenoid Module Fabrication September 2018 ITER Central Solenoid The heart of the international fusion energy device The Central Solenoid (CS) is the heart of ITER. The 5-story,
More informationGENERAL ATOMICS ITER CENTRAL SOLENOID MODULE FABRICATION
GENERAL ATOMICS ITER CENTRAL SOLENOID MODULE FABRICATION January 2018 ITER Central Solenoid The heart of the international fusion energy device The Central Solenoid (CS) is the heart of ITER. The 5-story,
More informationOverview of the ITER In-Vessel coil (IVC)
Overview of the ITER In-Vessel coil (IVC) 1. Purpose of the market survey With the present survey we would like to get from the Domestic Agencies a list of potential suppliers around the world for the
More informationGENERAL ATOMICS ITER CEnTRal SolEnoId ModulE FabRICaTIon August 2016
GENERAL ATOMICS ITER Central Solenoid Module Fabrication August 2016 ITER Central Solenoid The heart of the international fusion energy program The Central Solenoid (CS) is the heart of ITER. The 5-story,
More informationStatus of ITER at the Transition to Construction
Status of ITER at the Transition to Construction Guenter Janeschitz Deputy Head of Central Integration Office ITER Organisation Page 1 Outline Fusion Basics and History of ITER (very brief): ITER and its
More informationKSTAR Assembly. National Fusion Research Center, Daejeon, Korea
1 FT/2-2 KSTAR Assembly H. L. Yang, H. K. Kim, K. M. Kim, J. W. Sa, S. T. Kim, H. T. Kim, K. H. Hong, W. C. Kim, K. H. Kim, Y. S. Kim, J. Y. Kim, C. H. Choi, Y. K. Oh, Y. M. Park, M. Kwon, J. S. Bak, G.
More informationFuture opportunities for Industry
Neutral Beam Test Facility Heating Neutral Beam Injectors Electron Cyclotron Power Supplies and Sources Tullio Bonicelli and the NB&EC PSS Project Team with thanks to all European Laboratories and Industries
More informationSAFETY ON EVERY CURVE
SAFETY ON EVERY CURVE STEERING AHEAD The Mission of the Willi Elbe Group 2 Comprehensive development expertise, constantly up-to-date operational management, and state-of-the-art production. Discover here
More informationPrototyping of Axial Flux Permanent Magnet Motors
Prototyping of Axial Flux Permanent Magnet Motors Ferhat Daldaban and Emrah Çetin Faculty of Engineering Department of Electrical and Electronics Engineering Erciyes University, Turkey Contents; //CV //Axial
More informationDevelopment of a Superconducting High-Speed Flywheel Energy Storage System
Juni 2015 Development of a Superconducting High-Speed Flywheel Energy Storage System W. Walter 8. Braunschweiger Supraleiterseminar 2015 Outline Background SC bearing prototype Technology demonstrator
More information9-O-3A-4 Cryogenic system for the 43 T Hybrid Magnet at LNCMI Grenoble From the needs to the commissioning
9-O-3A-4 Cryogenic system for the 43 T Hybrid Magnet at LNCMI Grenoble From the needs to the commissioning L. Ronayette, G. Caplanne, P. Hanoux, R. Pfister, M. Pissard, P. Pugnat CNRS-LNCMI, Grenoble,
More informationReluctance Motors Synchrel Design & Optimisation
Reluctance Motors Synchrel Design & Optimisation A Switched Reluctance Alternative Incorporating Novel Features The End Result 1 Existing Design Procedure Electromagnetic Design A Switched Reluctance solution
More informationCosting of Test Articles Ancillary Equipment and Costing Methodology
Costing of Test Articles Ancillary Equipment and Costing Methodology 0.504 m x 1.71 m x 0.413 m C. Wong, S. Malang, M. Youssef, N. Morley, M. Ulrickson and the TBM design team US ITER-TBM Meeting August
More informationInstallation of High Speed Blowers
Installation of High Speed Blowers Cuts Electrical Costs & Improves Operations Thomas Schaffer, PE DBIA Senior Associate Outline Background Evaluation Blower Features Blower Project Examples Existing Conditions
More informationOverview of ITER Magnet System and European Contribution
2011 IEEEINPSS 24th Symposium on Fusion Engineering S03Dl Overview of ITER Magnet System and European Contribution C. Sborchia, E. Barbero Soto, R. Batista, B. Bellesia, A. Bonito Oliva, E. Boter Rebollo,
More informationTechnical Summary for BOP-Group 5 Installation Works The BOP Group 5 works include installation and commissioning of all the Items included in
IDM UID T244BP VERSION CREATED ON / VERSION / STATUS 03 May 2017 / 1.2 / Approved EXTERNAL REFERENCE / VERSION Technical Specifications (In-Cash Procurement) Technical Summary for BOP-Group 5 Installation
More information4.1. Manufacturing field F2 Preformed and field coil windings
4.1 Manufacturing field F2 Preformed and field coil windings 4.1.2.2 Manufacturing field F2 - Preformed and field coil windings 4.1.2.2.1 Range of services preformed coils One of the most important areas
More informationThe Results of the KSTAR Superconducting Coil Test
1 FT/3-2 The Results of the KSTAR Superconducting Coil Test Y. K. Oh, Y. Chu, S. Lee, S. J. Lee, S. Baek, J. S. Kim, K. W. Cho, H. Yonekawa, Y. Chang, K. R. Park, W. Chung, S. H. Lee, S. H. Park, I. S.
More informationUpdate on superconducting high-speed flywheel energy storage systems
Page 1 Babcock Noell GmbH Update on superconducting high-speed flywheel energy storage systems Michael Gehring, Achim Hobl, Wolfgang Walter, Cristian Boffo Babcock Noell GmbH Outline Page 2 Motivation
More informationVacuum pumps for the ESRF EBS project Michael Hahn
3 rd Rencontres Nationales DU RESEAU TECHNOLOGIES DU VIDE SEVRIER, 10 13 October 2016 Vacuum pumps for the ESRF EBS project Michael Hahn On behalf of the EBS Accelerator Project Team OUTLINE Project definition
More informationRisk Based Maintenance
Dai Richards ABB Eutech Risk Based Maintenance ABB Industries - 1 - Overview Delivering sustainable improvements is hard No time Changing priorities BU concepts appear well understood ABB Industries -
More informationDevelopment and Validation of A Dual Titanium Alloy Dual Microstructure BLISK
Development and Validation of A Dual Titanium Alloy Dual Microstructure BLISK Olaf Roder, MTU Aero Engines, Jean-Pierre Ferte, SNECMA, Ernst Gach, BSTG, Jose Mendez, CNRS-ENSMA, Marc Anglada, UPC and Antonio
More informationEU Procurement of In Vessel Components for ITER
EU Procurement of In Vessel Components for ITER State of progress and next steps Patrick Lorenzetto ITER Business Forum 2013, Toulon, 21 22 March 2013 1 Content Blanket First Wall Procurement Package Blanket
More informationReview and update on MAGLEV
EUROPEAN CRYOGENICS DAYS 2017 (Karlsruhe, Germany, September 13, 2017) Review and update on MAGLEV Hiroyuki Ohsaki The University of Tokyo, Japan Outline Review and update on MAGLEV 1. Introduction 2.
More informationDesign specifications
Design specifications Design To relevant standards: IEC, VDE, DIN, ISO, EN With squirrel-cage or slipring rotor Degree of protection IP 55 / IP 65 Cooling method IC511, suitable for both indoor and outdoor
More informationITER G A0 FDR R1.0
2.1 Magnets 2.1.1 Magnet System General Description 1 2.1.1.1 System Description and Main Parameters 1 2.1.1.2 Physical and Functional Interfaces 4 2.1.1.3 Heat Loads 6 2.1.2 Magnet Structures 7 2.1.2.1
More informationPDS COLLISION AVOIDANCE AACSA UNDERGROUND IMPLEMENTATION LEARNINGS
PDS COLLISION AVOIDANCE AACSA UNDERGROUND IMPLEMENTATION LEARNINGS Coal South Africa - 11 June 2015 Prepared for the SACEA Workshop 1 PDS BACKGROUND NEW DENMARK EXAMPLE SUCCESSES CHALLENGES AACSA COLLISION
More informationApproaches to Maintenance. S. Malang
Approaches to Maintenance S. Malang FNST Meeting, UCLA, August 12-14, 2008 Areas involved in the selection of methods for blanket maintenance: (Emphasis may be different for FNF and DEMO) - Segmentation
More informationMuni Forward: Get On Board! Siemens S200 SF Light Rail Vehicle
Muni Forward: Get On Board! Siemens S200 SF Light Rail Vehicle 07 15 2014 SAN FRANCISCO, CALIFORNIA 1 The Right Vehicle to Meet Increasing Demand for Rail Transit in the City Meets Central Subway time-table
More informationMinac. Mobile heat generators
Minac Mobile heat generators Introducing the Minac The Minac range of complete mobile induction systems is even easier to use than its acclaimed predecessor. A ready-to-use system, all that has to be done
More informationGlobal VPI Insulated Indirectly Hydrogen-Cooled Turbine Generator for Single-Shaft Type Combined Cycle Power Generation Facilities
Global VPI Insulated Indirectly Hydrogen-Cooled Turbine Generator for Single-Shaft Type Combined Cycle Power Generation Facilities YAMAZAKI Masaru NIIKURA Hitoshi TANIFUJI Satoshi ABSTRACT Fuji Electric
More informationHYSYS System Components for Hybridized Fuel Cell Vehicles
HYSYS System Components for Hybridized Fuel Cell Vehicles J. Wind, A. Corbet, R.-P. Essling, P. Prenninger, V. Ravello This document appeared in Detlef Stolten, Thomas Grube (Eds.): 18th World Hydrogen
More informationF4E NEWS. ITER Worksite Components Components Innovation Documentary. Fusion for Energy Newsletter No. 21 / May 2017
F4E NEWS Fusion for Energy Newsletter No. 21 / May 2017 ITER Worksite Components Components Innovation Documentary Buildings get ready to receive the first equipment Europe s first diagnostic components
More informationSeventh Framework Programme THEME: AAT Breakthrough and emerging technologies Call: FP7-AAT-2012-RTD-L0 AGEN
Seventh Framework Programme THEME: AAT.2012.6.3-1. Breakthrough and emerging technologies Call: FP7-AAT-2012-RTD-L0 AGEN Atomic Gyroscope for Enhanced Navigation Grant agreement no.: 322466 Publishable
More informationEnergy efficiency in New Member States and Candidate countries. Policies, potentials and needed action
Energy efficiency in New Member States and Candidate countries. Policies, potentials and needed action Paolo Bertoldi and Bogdan Atanasiu European Commission, Directorate General Joint Research Center
More informationDifferential Expansion Measurements on Large Steam Turbines
Sensonics Technical Note DS1220 Differential Expansion Measurements on Large Steam Turbines One of the challenges facing instrumentation engineers in the power generation sector is the accurate measurement
More informationProgress Report. Low and Realistic Winter Temperature TF WLTP 21 th - January The European Commission s science and knowledge service
The European Commission s science and knowledge service Joint Research Centre Progress Report Low and Realistic Winter Temperature TF WLTP 21 th - January 2018 C. Astorga CALEDAR OF TELCO & MEETING (after
More informationSteve Hsu, September Alternative Fuels & Vehicles Technology and Trend
Steve Hsu, September 6 2013 Alternative Fuels & Vehicles Technology and Trend 1 Agenda Introduction Hydrogen / Fuel Cell Vehicles Overview Electricity Vehicles Overview Wireless Charging System for Vehicles
More informationThe Regional Municipality of York. Purchase of Six Battery Electric Buses
1. Recommendations The Regional Municipality of York Committee of the Whole Transportation Services January 10, 2019 Report of the Commissioner of Transportation Services Purchase of Six Battery Electric
More informationCreating A Greener Energy Future For the Commonwealth. Massachusetts Solar Carve-Out (SRECs): Overview & Program Basics.
Massachusetts Solar Carve-Out (SRECs): Overview & Program Basics December 18, 2012 Outline Learn how the solar PV market has grown in MA since 2007 Understand the policy design of the MA Solar Carve-Out
More informationContent. 04 The Company. 13 Key to symbols. 22 Double walled tanks heads. 14 Dished heads table. 06 The catalogue and guide for the consultation
GENERAL CATALOGUE Content 04 The Company 06 The catalogue and guide for the consultation 08 Certifications 10 Technical notes 12 Materials 13 Key to symbols 14 Dished heads table 16 Dished head type D
More informationGROUP PRESENTATION. Milan, March 27 th &28 th 2012 SOGEFI GROUP
GROUP PRESENTATION Milan, March 27 th &28 th 2012 1 PARIS, March OCTOBER 27 & 28 2012 11th WORLD LEADER Sogefi is a world leader in the design and manufacturing of engine filtration, air intake and cooling
More informationUK gas and electricity supplies. A review of the winter John Greasley and Simon Griew Commercial. UK Transmission
UK gas and electricity supplies A review of the winter 2003-04 John Greasley and Simon Griew Commercial UK Transmission Agenda What were we saying before the winter? What happened in electricity? What
More informationPresented by B. Nelson for the QPS team QPS Conceptual Design Review June 23-24, 2003 ORNL
QPS Project Implementation Presented by B. Nelson for the QPS team QPS Conceptual Design Review June 23-24, 2003 ORNL Presentation Outline Fabrication Plans How we plan to build QPS R&D, primarily Modular
More informationTechnical Summary. Contract for Procurement of Manual Valves, Relief Valves, Control Valves, and Valve Actuators (IO/15/CFT/11867/ACS CP/3)
Purpose Technical Summary Contract for Procurement of Manual Valves, Relief Valves, Control Valves, and Valve Actuators (IO/15/CFT/11867/ACS CP/3) The purpose of this Call for Nominations is to establish
More informationOFF-PEAK DELIVERIES. Ontario Trucking Association June 26 th, Goods Movement Office Transportation Policy Branch Ministry of Transportation
OFF-PEAK DELIVERIES Ontario Trucking Association June 26 th, 2015 Goods Movement Office Transportation Policy Branch Ministry of Transportation 2 Outline Off-Peak Deliveries Pilot Background Phase One
More informationTABLE OF CONTENTS. Issue Date Subject Hoses Affected Fittings Affected Page A Crimp Specification Updates 120J
TABLE OF CONTENTS Issue Date Subject Hoses Affected Fittings Affected Page 2017-02-24A 120J 4200 2 2016-07-04A 141-20 4200 3 4400 5000 2016-07-04B 122-12 4200-12 4 122A-12 2016-07-04C 124PLUS-08 4400-08
More informationIntegrated Powertrain Simulation for Energy Management of Hybrid Electric Vehicles
Integrated Powertrain Simulation for Energy Management of Hybrid Electric Vehicles October 24 th, 2011 Kentaro Watanabe Nissan Motor Co., Ltd. 1 Outline 1. Motivation 2. Simulation technology 3. Recent
More information2011 Special Reliability Assessment: Power Interdependency in the United States
2011 Special Reliability Assessment: A Primer on the Natural Gas and Electric Power Interdependency in the United States John Moura Highlights Key differences exists between gas and electricity producers
More informationEVSE Standards Status Gery Kissel SAE J1772 Task Force Lead July 26, 2011
EVSE Standards Status Gery Kissel SAE J1772 Task Force Lead July 26, 2011 Contents Charging Configurations and Ratings Document Status Revision Plan DC Fast Charge Standardization DC Fast Charge Coupler
More informationDriving Efficiency In Commercial Vehicle Engine Lubricants. Nigel Britton, Technical Manager
Driving Efficiency In Commercial Vehicle Engine Lubricants Nigel Britton, Technical Manager 5 th April 2017 Topics The drivers for greater efficiency in heavy duty commercial vehicles Why fuel economy
More informationIntegrated Engine and Aftertreatment System Technology for EPA 2010 Heavy-duty Emissions Regulations
Integrated Engine and Aftertreatment System Technology for EPA 2010 Heavy-duty Emissions Regulations Presented by: Rakesh Aneja Engine Systems and Technology Detroit Diesel Corporation Series 60 MBE 900
More informationNo. 64, 30 April 2015
JT-60SA Newsletter No. 64, 30 April 2015 Headline Ceremony for JT-60SA On 20 April 2015, JAEA held a Celebration of the delivery of main components and start of their on-site installation by EU, and completion
More informationAdvanced Catalyst Systems for HDD On-Road BS VI and Off-Road Trem IV
ECMA 11 th International Conference & Exhibition - 2018, Pune, India, Oct. 25-26, 2018 Advanced Catalyst Systems for HDD On-Road BS VI and Off-Road Trem IV Weiyong Tang, Ph.D. Mobile Emissions Catalysts
More informationEnergy ITS: What We Learned and What We should Learn
Energy ITS: What We Learned and What We should Learn July 25, 2012 TRB Road Vehicle Automation Workshop Sadayuki Tsugawa, Dr. Eng. NEDO Energy ITS Project Leader Professor, Department of Information Engineering
More informationMOST MODERN COMBINATION PICKLING AND GALVANIZING LINE
MITHALESHWAR YADAV SENIOR SALES MANAGER DANIELI INDIA LTD. 4 TH GALVANIZING COATING & PROFILING SUMMIT 12 TH FEBRUARY 2016 MUMBAI MOST MODERN COMBINATION PICKLING AND GALVANIZING LINE COMBINATION PICKLING
More informationCity of Philadelphia Renewable Energy Power Purchasing RFP Pre-Proposal Meeting
City of Philadelphia Renewable Energy Power Purchasing RFP Pre-Proposal Meeting City Energy Office October 25, 2017 For Participants on the Phone Follow along with slides posted at: http://www.philaenergy.org/public_bids/renewable-energypower-purchasing-agreement-request-for-proposal/
More informationINFODAY Brussels, June 23,2009 Griet Van Caenegem, Directorate G Components and Systems Unit Microsystems
European Green Cars Initiativethe ICT call5 INFODAY Brussels, June 23,2009 Griet Van Caenegem, Directorate G Components and Systems Unit Microsystems OUTLINE Context: recovery package European Green Cars
More informationKey Stellarator Engineering Issues and Constraints
Key Stellarator Engineering Issues and Constraints P. Heitzenroeder for the NCSX Engineering Team ARIES Meeting at PPPL - October, 2002 1 How The Engineering of a Compact Stellarator Differs from Most
More informationTire Uniformity Machine, LIBROTA
Tire Uniformity Machine, LIBROTA Shinichiro IKAI *1, Yasuhiro MATSUSHITA *2 *1 Machinery Business Industrial Machinery Division Industrial Machinery Department *2 Machinery Business Industrial Machinery
More informationValue Paper Author: Mats G Olsson. IDC, Interstand Dimension Control Field experience at Shiu Wing Steel, Hong Kong
Value Paper Author: Mats G Olsson IDC, Interstand Dimension Control Field experience at Shiu Wing Steel, Hong Kong Field experience at Shiu Wing Steel, Hong Kong Synopsis Field experience is proving not
More informationThe g-2 Project at FNAL. Horst Friedsam John Kyle IWAA 2014 at Beijing October 2014
Horst Friedsam John Kyle IWAA 2014 at Beijing 13-17 October 2014 Outline History and project purpose P5 and the Muon Campus development The meaning of the gyromagnetic ratio g Alignment requirements Status
More informationThis chapter gives details of the design, development, and characterization of the
CHAPTER 5 Electromagnet and its Power Supply This chapter gives details of the design, development, and characterization of the electromagnets used to produce desired magnetic field to confine the plasma,
More informationThe Wendelstein 7-X trim coil system
1 The Wendelstein 7-X trim coil system Thomas Rummel, Konrad Riße, Frank Füllenbach, Matthias Köppen, Johann Kißlinger, Tom Brown, Ron Hatcher, Stephen Langish, Mike Mardenfeld, and Hutch Neilson Abstract
More informationABB Power Cables Service Turnkey Cable Repairs Three Reference Cases
ABB Power Cables Service, ABB Power Cables Service Turnkey Cable Repairs Three Reference Cases July 16, 2013 Slide 1 ABB Power Cables Service Success Repair Story Wind Farm, United Kingdom, March 2012
More informationPrecision Station Stopping Progress Update
Washington Metropolitan Area Transit Authority Precision Station Stopping Progress Update Presented to: The Board of Directors; Customer Service, Operations and Safety Committee By PlanninghDevelopmenthEngineeringhConstruction
More informationChallenges With Underground High Voltage Transmission SCE Tehachapi Renewable Transmission Project First 500 kv Underground T/L in North America
Challenges With Underground High Voltage Transmission SCE Tehachapi Renewable Transmission Project First 500 kv Underground T/L in North America Noe Bargas, PE Supervising Senior Civil Engineer Southern
More informationHeavy-Duty Diesel Engine Trends to Meet Future Emissions Standards (Euro VI)
Heavy-Duty Diesel Engine Trends to Meet Future Emissions Standards (Euro VI) Andrew Nicol AECC Technical Seminar on Heavy-Duty Vehicle Emissions (Euro VI) Brussels 25 October 2007 Contents Emissions Legislation
More informationHigh Quality Coil Manufacturing
a Parsons Peebles company High Quality Coil Manufacturing Superior quality coils for high voltage motors, generators and traction motors delivered in days, not weeks 02 High Quality Coil Manufacturing
More informationSiemens AG SIMOTICS T-1FW3 Torque Motors. The Powerful Torque Motors. Edition February Brochure. siemens.
SIMOTICS T-1FW3 Torque Motors The Powerful Torque Motors Brochure Edition February 2017 siemens.com/torquemotors The powerful torque motors Overview The right torque at the right moment this is decisive
More informationMIT ICAT M I T I n t e r n a t i o n a l C e n t e r f o r A i r T r a n s p o r t a t i o n
M I T I n t e r n a t i o n a l C e n t e r f o r A i r T r a n s p o r t a t i o n Standard Flow Abstractions as Mechanisms for Reducing ATC Complexity Jonathan Histon May 11, 2004 Introduction Research
More informationThe Easy Way to Electromobility
European Green Car Initiative 10 July 2012, Brussels Panel Impact and future Outlook The Easy Way to Electromobility 1 Outline Enabling tech are evolving fast: Promote ambitious EU targets Relative risk
More informationSmall Scale Cooler: Extending Space Developed Technology into Adjacent Markets
C19_043 1 Small Scale Cooler: Extending Space Developed Technology into Adjacent Markets P. Iredale, C. F. Cheuk, N. Hardy, S. Barclay, M. Crook 1, G. Gilley 1 and S. Brown 1 Honeywell Hymatic, Redditch,
More informationMinac. Mobile heat generators
Minac Mobile heat generators Introducing the Minac The Minac range of complete mobile induction systems is even easier to use than its acclaimed predecessor. A ready-to-use system, all that has to be done
More informationOPTIMIZE PERFORMANCE
DuraTaq TM Compound Comparison Chart 1 USING CUSTOM BELT MODIFICATIONS TO OPTIMIZE PERFORMANCE beltcorp.com BELT CORPORATION Using Custom Belt Modifications to Optimize Performance Introduction Belt modifications
More informationImproving Valve Fugitive Emissions Performance
Improving Valve Fugitive Emissions Performance Steve McJones and Rich Sobilo March 6, 2014 Steve McJones Advisor Pressure Vessels, Piping and Valves BP Refining & Logistics Technology Support BP Refineries
More informationUser Manual for the RAMK Rotational Absolute Magnetic Kit Encoder
VISHAY MCB www.vishay.com Variable Resistors By Frederic Bourget and Emmanuel Lemelle INTRODUCTION The purpose of this user manual is to define the precautions for unpacking, mounting, and using RAMK encoder
More informationDesign and evaluate vehicle architectures to reach the best trade-off between performance, range and comfort. Unrestricted.
Design and evaluate vehicle architectures to reach the best trade-off between performance, range and comfort. Unrestricted. Introduction Presenter Thomas Desbarats Business Development Simcenter System
More informationEvaluating the Techno-Economics of Retrofitting CO2 Capture Technologies in an Integrated Oil Refinery (Progress Report) Stanley Santos
Evaluating the Techno-Economics of Retrofitting CO2 Capture Technologies in an Integrated Oil Refinery (Progress Report) Stanley Santos IEA Greenhouse Gas R&D Programme Industry CCS Workshop Vienna, Austria
More informationENGINEERING & SERVICES PVT LTD
ENGINEERING & SERVICES PVT LTD www.sankalpenggservices.com CERTIFICATIONS About Sankalp Incorporated in 1996, Sankalp focused in Oil & Gas Field Components, primarily OCTG, Well Head, Drilling and Down
More informationABS keeps the vehicle steerable, even during an emergency braking
ABS keeps the vehicle steerable, even during an emergency braking under all road conditions 1 Contents! Safety systems in vehicles! Why do you need ABS?! How does ABS work?! What are the benefits of ABS?!
More informationCompact HH-553 Handheld Riveter
Copyright 2008 Society of Automotive Engineers, Inc. 08 FAS 0014 Compact HH-553 Handheld Riveter Zory Taskar, Brian Tocco, Isao Uetake (MHI, Japan) Electroimpact, Inc. ABSTRACT The handheld (HH) electromagnetic
More informationSiemens AG Synchronous linear motor 1FN6. The electrical gear rack. Brochure September Motors
The electrical gear rack Brochure September 2008 Motors Overview Linear motors are preferred for applications with linear axes in machine and plant engineering with stringent requirements for dynamic response
More informationAdditive Manufacturing at voestalpine
Additive Manufacturing at voestalpine Current applications from Topology optimization, tool manufacturing and special engineering www.voestalpine.com AGENDA 2 05. October 2017 Additive Manufacturing at
More informationVolvo. Volvo Cars is the passenger vehicle maker now owned by Ford Motor Company, using the Volvo Trademark. AB Volvo. Worldwide
Volvo Volvo Cars is the passenger vehicle maker now owned by Ford Motor Company, using the Volvo Trademark. AB Volvo Type Public (OMX: VOLV B) Founded 1927 by SKF Headquarters Gothenburg, Sweden Area served
More informationTHE Gersh Budker Prize PRIZE FOR.THE SUCCESSFUL CONSTRUCTION AND COMMISSIONING OF THE SPALLATION NEUTRON SOURCE
THE Gersh Budker Prize PRIZE FOR.THE SUCCESSFUL CONSTRUCTION AND COMMISSIONING OF THE SPALLATION NEUTRON SOURCE EPAC08, Genoa (Italy) 26 June 2008 1451 1506 1918 1977 Norbert Holtkamp Principal Deputy
More informationSUSPENSION 04 CLAMPS
SUSPENSION CLAMPS 04 4 SUSPENSION CLAMPS 57 Contents General... 58 Suspension clamp trunnion type, forged,... 63 Suspension clamp trunnion type, forged, with bigger angle of deflection, for aluminium based
More informationHRSG Operational Challenges and Siemens Solutions
Intelligent Energy Solutions HRSG Operational Challenges and Siemens Solutions Gary Gong Ph.D P.E. Siemens Energy Inc 4400 N Alafaya Trl Orlando, FL 32766 Siemens Energy, Inc. Siemens 2010. All Energy,
More informationYanmar Introduces Two High-Power Industrial Diesel Engines
News Release April 23, 2018 Yanmar Co., Ltd. Yanmar Introduces Two High-Power Industrial Diesel Engines 4TN107 Industrial Diesel Engine OSAKA, Japan (April 23, 2018) Yanmar has developed two new high-power
More informationPV Master OPERATION MANUAL
PV Master OPERATION MANUAL GoodWe Technical Services Center December, 2017 Ver. 1.00 BRIEF INTRODUCTION PV Master is an external application for GoodWe inverters to monitor or configure inverters or to
More informationPre Commercial Procurement Austrian Pilot Calls
Pre Commercial Procurement Austrian Pilot Calls MLE Innovation Procurement, November 29th 2017, Madrid Jeannette Klonk, Austrian Research Promotion Agency ANCHORING PCP IN THE AUSTRIAN R&I POLICY CONTEXT
More informationUltrasonic and Magnetic Particle Testing of New Railway Wheels
19 th World Conference on Non-Destructive Testing 2016 Ultrasonic and Magnetic Particle Testing of New Railway Wheels Wolfram A. Karl DEUTSCH 1, Wolfgang WEBER 1, Klaus MAXAM 1, Mathias RAZENG 1, Frank
More informationReduced Stopping Distance: Why the Mandate?
Reduced Stopping Distance: Why the Mandate? According to the Federal Motor Carrier Safety Administration (FMCSA): Overall the fatality rate for large truck crashes was 66 percent higher than passenger
More information